ROCK STAR. User Guide. Windshield Repair System. Part# RSR Equalizer Industries, Inc.

Size: px
Start display at page:

Download "ROCK STAR. User Guide. Windshield Repair System. Part# RSR Equalizer Industries, Inc."

Transcription

1 ROCK STAR Windshield Repair System Part# RSR800 User Guide 2012 Equalizer Industries, Inc. Revision 11/10/17

2 11. Clean the area that you have worked on with a good glass cleaner and a paper towel. VBA1443 Cleaning & Maintenance 1. Clean the resin off of (and out of) your injector, o-rings and bridge with our cleaning solution. *Keeping these items clean and free of build up assures no contamination on you next repair, proper functioning of the tools, and will increase the longevity of the tools. Failure to properly clean and maintain these items could result in voiding your warranty! 3.5 mm thick 13 mm outer diameter 6 mm inside diameter 2.5 mm thick 10 mm outer diameter 4 mm inside diameter 2 mm thick 13 mm outer diameter 10 mm inside diameter 2 mm thick 12 mm outer diameter 8 mm inside diameter 1 VOR

3 Always wear safety glasses and nitrile gloves when repairing a windshield! Inspection And Assessment - 1. Examine the damaged area from the inside and outside of the vehicle. Look for hidden cracks, moisture, contamination or previous repair attempts. 2. Determine if the damage is within the scope of your technical experience to repair. 3. Assess to make sure that the windshield is at the appropriate temperature. Ideal temperature is between 65 F to 85 F plus or minus 5 F. Preparing the Rock Chip - 1. Place the mirror on the inside of the windshield, under the damaged area. 2. Clean around the damaged area. Be sure to place a nitrile glove-covered finger over the rock chip in order to keep from contaminating the break. 2

4 3. Using the probe, remove broken glass debris from the chip. 4. If moisture is present in the break, dry out by using the windshield chip moisture evaporator. 5. If the rock chip area is not open, consider drilling the chip. At a slow setting start to drill into the glass but be careful not to drill into the PVB (Poly Vinyl Butyral) Preparing the Bridge and Injector Assembly - 1. Place the injector tip o-ring on the end of the injector assembly. To do so, use a small drop of resin to wet the injector assembly tip and then put the o-ring in place. 3

5 2. Screw the injector assembly into the bridge. If the rock chip area is larger than the o-ring on the injector assembly tip, then add the large pit adaptor onto the unit. 3. Place a light film of vacuum cup lubricant onto the vacuum cup of the bridge and on the two bridge adjusting screws. Once the bridge and injector assembly is set up on the glass this will help to move the unit if the o-ring placement needs to be adjusted. 4

6 4. Make sure that the injector assembly and bridge adjusting screws are backed out enough so that they do not make contact with the glass until the vacuum cup is fully engaged on the glass. Note: If the injector assembly and bridge adjusting screws are not backed far enough out, this could result in applying pressure and causing further damage to the break. Setting Up the Bridge and Injector Assembly - 1. Place the bridge and injector assembly onto the glass so that the injector tip o-ring is over the rock chip. 2. Secure the bridge by flipping the vacuum cup lever. 3. Screw the injector assembly down until the o-ring makes contact with the surface of the glass. 4. Screw the bridge adjusting screws down equally until the o-ring has a flat look to its appearance. This will ensure that the o-ring is snug enough to create an airtight seal. Note: Always make sure not to over-tighten the injector assembly or the bridge adjusting screws. This could cause further damage to the break. 5

7 Injection Procedure - 1. Loosen the injector pressure rod. 2. Remove the injector from the barrel. 3. Place between 3 to 5 drops of resin into the injector barrel. *Always make sure to use the right resin for the job. If the temperature of the work area is warm or the job is at high altitude; always use a thicker resin. If the temperature of the work area is cool or at sea level use a thinner resin. 4. Wet the two o-rings on the injector tip using resin. 5. Place the injector back into the injector barrel making sure that the groove on the injector lines up with the retaining screw. Adjust the retaining screw so that the threaded end of the screw slips into the groove and is just tight enough for the injector to move freely up and down but not be removed from the barrel (the end of the groove on the injector will catch the retaining screw and stop). 6

8 6. Now push the injector in until it hits the bottom of the barrel. 7. Tighten the injector pressure rod. 8. Pull the injector up until the end of the groove makes contact with the retaining screw. Fully tighten the retaining screw. You are now in the vacuum phase. 9. Hold vacuum for one minute. 10. Next, release the vacuum by loosening the injector pressure rod. 11. Then re-tighten the injector pressure rod to secure the seal. 12. Next, loosen the retaining screw and push the injector in a downward motion until the point when you feel resistance. Then tighten the retaining screw. You are now in the pressure phase. 13. Hold pressure for two minutes. Note: For stubborn breaks, you might have to repeat the vacuum to pressure cycle until the break is fully filled. Applying a little pressure on your break with your probe will flex the break and help move resin into the tight areas. 7

9 Curing Procedure - 1. When the repair is to your satisfaction, release the pressure by loosening the injector pressure rod. 2. Release the lever on the vacuum cup. 3. Remove the bridge and injector assembly. 4. Wipe away any residual resin. 5. Apply a drop of pit filler resin. 6. Place a mylar square cure sheet onto the pit filler resin. Be sure to gently place the cure sheet in a downward laying motion and let gravity do the rest. 8

10 7. Cure the break for approximately three minutes using either an ultra violet lamp or the use of natural sun light. *Always make sure to let the break cure to the required allotted time. Do Not rush this process. The outer part of the break might be cured but the actual pit may not be. It is very important that it be cured all the way through. 8. Remove the mylar square cure sheet. 9. With the use of a new razor blade, scrape the cured resin in a back and forth, up and down motion until the resin is even and level with windshield. 10. Apply a small amount of pit polish and vigorously buff with a soft cloth or paper towel until the pit resin is shiny. 9

11 11. Clean the area that you have worked on with a good glass cleaner and a paper towel. VBA1443 Cleaning & Maintenance 1. Clean the resin off of (and out of) your injector, o-rings and bridge with our cleaning solution. *Keeping these items clean and free of build up assures no contamination on you next repair, proper functioning of the tools, and will increase the longevity of the tools. Failure to properly clean and maintain these items could result in voiding your warranty! 3.5 mm thick 13 mm outer diameter 6 mm inside diameter 2.5 mm thick 10 mm outer diameter 4 mm inside diameter 2 mm thick 13 mm outer diameter 10 mm inside diameter 2 mm thick 12 mm outer diameter 8 mm inside diameter 1 VOR

12 Additional Accessories RB497 VUV1447 VCD1464 VPT1489 MS492 DL1093 BNG418 BNL820 VTR1448 VTL1449 VMR1450 VML1451 VPF1452 VPL1453 VAF1471 VAL1472 TRR652 TRO653 VPO1455 VCB1454 AVL Oakmont Drive Round Rock Texas Toll Free USA & Canada: International: Fax:

Windshield Repair Instruction Manual

Windshield Repair Instruction Manual Windshield Repair Instruction Manual 1 of 9 Table of Contents 1. Know the benefits of WSR... 3 2. Types of breaks... 3 3. Repair limitations... 3 4. Equipment introduction... 3 5. Safety... 4 6. Preparation

More information

FRAMED SLIDING DOOR FOR TUB OR SHOWER ENCLOSURE 6150A-7150A

FRAMED SLIDING DOOR FOR TUB OR SHOWER ENCLOSURE 6150A-7150A FRAMED SLIDING DOOR FOR TUB OR SHOWER ENCLOSURE 6150A-7150A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com

More information

1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A

1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A 1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com

More information

FRAMED SLIDING DOOR FOR TUB OR SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS

FRAMED SLIDING DOOR FOR TUB OR SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS FRAMED SLIDING DOOR FOR OR SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS QCI5023 REV. 0 Page 1 Certified 06/22/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay out and

More information

1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward.

1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward. Figure 1 Miniature Quick Change Applicators, of the end feed type, are designed to crimp end feed strip terminals to prestripped wires. Each applicator is set up to accept the strip form of certain specific

More information

Frameless Fixed Panel Slider QCI5279

Frameless Fixed Panel Slider QCI5279 Frameless Fixed Panel Slider QCI5279 F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com Frameless Fixed Panel

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS BUILDERS CHOICE FRAMED Bypass Door Model: L0516 (Tub Height), L0517 (Shower Height) Rev. 09.20.13 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage.

More information

tile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE:

tile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: redi DOOR INSTALLATION INSTRUCTIONS tile redi Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: 3000 Door-Door Header, sliding doors RDQCI5301

More information

935 RODA VINESSE NEED INSTALLATION HELP? DOUBLE ROLLERS FRAMELESS DOOR INSTALLATION INSTRUCTIONS QCI XX/XX/XXXX. Call BASCO ( )

935 RODA VINESSE NEED INSTALLATION HELP? DOUBLE ROLLERS FRAMELESS DOOR INSTALLATION INSTRUCTIONS QCI XX/XX/XXXX. Call BASCO ( ) INSTALLATION INSTRUCTIONS 935 RODA DOUBLE ROLLERS FRAMELESS DOOR NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday VINESSE QCI0286 1 XX/XX/XXXX 935 Roda Parts List With double rollers

More information

Fender Protectors. To ensure a successful installation, please read all of these instructions prior to starting.

Fender Protectors. To ensure a successful installation, please read all of these instructions prior to starting. Fender Protectors To ensure a successful installation, please read all of these instructions prior to starting. General Instructions All Tough Stuff Protective Products use a waterproof contact adhesive.

More information

Elcometer Muller Laboratory Grinder

Elcometer Muller Laboratory Grinder English Elcometer 2000 Muller Laboratory Grinder Operating Instructions English is a registered trademark of Elcometer Limited. All other trademarks acknowledged. Copyright Elcometer Limited. 2009. All

More information

5. Carefully remove the printer from the lower boxed foam support and place it on a solid, level base where it will be used

5. Carefully remove the printer from the lower boxed foam support and place it on a solid, level base where it will be used PROJET 1200 QUICKSTART GUIDE Before you get started you will need: Lint-free paper towels A pair of nitrile gloves Saftety glasses OPENING YOUR PROJET 1200 NOTE: Make sure you save all of your packaging

More information

Model: SCD430 SCD640. Installation & Operation Guide P/N SCD640-95

Model: SCD430 SCD640. Installation & Operation Guide P/N SCD640-95 Model: SCD430 SCD640 Installation & Operation Guide P/N SCD640-95 Model SCD430 and SCD640 Kurt has two Self-Centering vises, a four-inch jaw width (SCD430) and a six-inch jaw width (SCD640). Jaw opening

More information

Unit No. 6150, 7150 Deluxe Framed Sliding Tub/Shower Enclosure

Unit No. 6150, 7150 Deluxe Framed Sliding Tub/Shower Enclosure INSTALLATION INSTRUCTIONS Unit No. 6150, 7150 Deluxe Framed Sliding Tub/Shower Enclosure QCI0023 Rev. 1 Page 1 of 8 Certified 8/20/10 MAINTENANCE: Two primary materials are used to manufacture your new

More information

tile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE:

tile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: redi DOOR INSTALLATION INSTRUCTIONS tile redi Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: 1100 Door-Door Framed sliding doors RDQCI5023

More information

How to use a Touch Up Bottle & Brush

How to use a Touch Up Bottle & Brush How to use a Touch Up Bottle & Brush Tech Tips General Definitions Base Color (Basecoat): A color coat requiring a clear coat. Base Color provides color and appearance, while the clear coat provides gloss

More information

High Speed Air Turbine Handpiece

High Speed Air Turbine Handpiece OPERATION MANUAL High Speed Air Turbine Handpiece Please read this Operation Manual carefully before use and file for future reference. Handpiece should not be used with friction grip burs exceeding 18.5

More information

SETTING UP THE MODEL 210B

SETTING UP THE MODEL 210B SETTING UP THE MODEL 210B SAFETY PRECAUTIONS FOR THE MODEL 210B System Under Pressure: Shut off air supply and disconnect air hose before disassembling or disconnecting parts. Flying Debris: During boring,

More information

Standard Kit #1 (3-way switch)

Standard Kit #1 (3-way switch) Standard Kit #1 (3-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable

More information

Frameless Inline Door QCI5250

Frameless Inline Door QCI5250 INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5250 FRAMELESS PANEL / DOOR / PANEL QCI0249 REV. 3 Page 1 Certified 10/12/12 Parts List with pivot hinges *Quantities may vary. QCI0249 REV. 3 Page 2

More information

SUPER PRO GUN & SUPER PRO GUN II

SUPER PRO GUN & SUPER PRO GUN II MAGNUM VENUS PRODUCTS Maintenance & Repair Manual Part No. M6707-1-1 Revision 04.14.01 Maintenance & Repair Corporate HQ & Mfg. Phone: (727) 573-2955 Fax: (727) 571-3636 Email: info@magind.com Web: www.magind.com

More information

3 Emergency Breakaway Coupling

3 Emergency Breakaway Coupling SM64227 July 2008 Applicable addition manuals: N/A Aerospace Group Conveyance Systems Division Carter Ground Fueling Maintenance & Repair Manual 3 Emergency Breakaway Coupling Model 64227 Table of Contents

More information

QCI0029 REV. 1 Page 1 of 11 Certified 07/06/05

QCI0029 REV. 1 Page 1 of 11 Certified 07/06/05 QCI0029 REV. 1 Page 1 of 11 Certified 07/06/05 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure: tempered glass and anodized aluminum. To assure a long lasting finish

More information

INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233

INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233 INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233 QCI5233 Rev 0 Page 1 Certified 06/20/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay

More information

4.2 - PUMP MAINTENANCE MODELS: AC, AS, WC, WS

4.2 - PUMP MAINTENANCE MODELS: AC, AS, WC, WS 4.2 - PUMP MAINTENANCE MODELS: AC, AS, WC, WS 4.2.1 - EXPLODED VIEW DRAWING REF NO. 1 2 4 QTY 3 1 1.5 5 ¾ HP HP HP HP HP DESCRIPTION PART # 1 CASE 1.25 x 1 NPT 018266 1 CASE 1.25 X 1 NPT 018268 1 CASE

More information

TYPE 3740/3740D WET/DRY RUNNING CARTRIDGE SPLIT SEAL

TYPE 3740/3740D WET/DRY RUNNING CARTRIDGE SPLIT SEAL 1 Foreword These instructions are provided to familiarize the user with the seal and its designated use. The instructions must be read and applied whenever work is done on the seal, and must be kept available

More information

Frameless Fixed Panel Slider

Frameless Fixed Panel Slider INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need

More information

Pump Replacement Manual. Bill Wallace by Wallace Marine Services, Inc.

Pump Replacement Manual. Bill Wallace by Wallace Marine Services, Inc. by Wallace Marine Services, Inc. Maintain Your Equipment The Easy Way Bill Wallace 843-693-4336 info@willyvac.com www.willyvac.com Pump Replacement Manual 1 How to change the water pump on the Willy Vac

More information

Palladian/ Keystone Models 202/204 Maintenance Kit

Palladian/ Keystone Models 202/204 Maintenance Kit Palladian/ Keystone Models 202/204 Maintenance Kit Please read all of the instructions before you begin. Confirm that you have all the necessary tools and parts required. Allow about one hour to complete

More information

3/8 FRAMELESS BYPASS SLIDING SHOWER ENCLOSURE

3/8 FRAMELESS BYPASS SLIDING SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS 3/8 FRAMELESS BYPASS SLIDING SHOWER ENCLOSURE QCI-5017 QCI5017 Rev. 3 Page 1 of 9 Certified 12/6/17 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage.

More information

INSTALLATION INSTRUCTIONS FIXED PANEL SLIDER FRAMELESS DOOR / PANEL. QCI0280 Page 1 Cer fied 6/27/14

INSTALLATION INSTRUCTIONS FIXED PANEL SLIDER FRAMELESS DOOR / PANEL. QCI0280 Page 1 Cer fied 6/27/14 INSTALLATION INSTRUCTIONS FIXED PANEL SLIDER FRAMELESS DOOR / PANEL QCI0280 Page 1 Cer fied 6/27/14 VINA-935 Parts List ITEM NO. 1 2 NUMBER DESCRIPTION QTY. CLZ2278-13A (44"-47") CLZ2878-13A (56"-59")

More information

SETTING UP THE MODEL 85B

SETTING UP THE MODEL 85B SETTING UP THE MODEL 85B SAFETY PRECAUTIONS FOR THE MODEL 85B System Under Pressure: Shut off air supply and disconnect air hose before disassembling or disconnecting parts. Flying Debris: During boring,

More information

Masking: Each mirrored sheet is well protected by a durable paint backing and

Masking: Each mirrored sheet is well protected by a durable paint backing and STORAGE Horizontal storage: If mirror sheets are stored flat, care must be taken to avoid warping, slipping and scratching. If different sizes are stored together the largest panels should at the bottom

More information

8" BENCH SHEAR INSTRUCTIONS. Item #20198

8 BENCH SHEAR INSTRUCTIONS. Item #20198 8" BENCH SHEAR INSTRUCTIONS Item #20198 Your EASTWOOD 8 BENCH SHEAR for metal cutting is designed for quickly and cleanly cutting mild steel, aluminum and other metals. Torque-amplifying, compound linkage

More information

Clarinet/Bass Clarinet Care

Clarinet/Bass Clarinet Care Flute/Piccolo Care When assembling your instrument, be careful that pressure is not applied to the keys or rods. Do not put it together at an angle and then wiggle it together. Make certain each part is

More information

Frameless Bypass Slider

Frameless Bypass Slider INSTALLATION INSTRUCTIONS Frameless Bypass Slider QCI-5301 Heavy Glass Bypass Slider with Exposed Rollers QCI5301 Rev 0 Page 1 Certified 11/1/2016 Tools: To install your New Shower Enclosure, you may need

More information

H8508 Impact Wrench SERVICE MANUAL. Model (Serial Code FWN) Model (Serial Code FWP)

H8508 Impact Wrench SERVICE MANUAL. Model (Serial Code FWN) Model (Serial Code FWP) SERVICE MANUAL H8508 Impact Wrench Model 48755 (Serial Code FWN) Model 48760 (Serial Code FWP) Read and understand all of the instructions and safety information in this manual before operating or servicing

More information

EXIT DEVICE OPERATION FIRE DOOR LABELS, STRIKES AND FRAME SCREWS FOR INFORMATION CALL OR VISIT RITEDOOR.COM

EXIT DEVICE OPERATION FIRE DOOR LABELS, STRIKES AND FRAME SCREWS FOR INFORMATION CALL OR VISIT RITEDOOR.COM RECORD & LABELS WHAT THIS OWNER'S CAN DO FOR YOU It explains exactly how The Rite Door operates. It explains periodic maintenance requirements necessary to assure reliable operation. It explains simple

More information

The DeltaGrip System. Safety and Operating Instructions. Trigger. Air Supply Connection. Handle Assembly. Air Line Assembly.

The DeltaGrip System. Safety and Operating Instructions. Trigger. Air Supply Connection. Handle Assembly. Air Line Assembly. The DeltaGrip System Safety and Operating Instructions Trigger Air Supply Connection Handle Assembly Air Line Assembly Punch Die Pneumatic Diaphragm Assembly Shackle, Pin & Jam Nut Jaw Frame Shoulder Screw

More information

Assembly Manual. OLM Retractable Canopy for 12X16 Breeze Pergola by Outdoor Living Today. Revision #12 October 4, 2017

Assembly Manual. OLM Retractable Canopy for 12X16 Breeze Pergola by Outdoor Living Today. Revision #12 October 4, 2017 Assembly Manual OLM Retractable Canopy for 12X16 Breeze Pergola by Outdoor Living Today Revision #12 October 4, 2017 Care and Maintenance - Canopy should be removed in winter to reduce the chance of collapse

More information

Maintenance & Parts list for:

Maintenance & Parts list for: Maintenance & Parts list for: Industrial gun GB 2 Juni 2017 This Maintenance & Parts list for industrial gun is prepared by : Winchester Europe Service V. Parbst & Søn as a comprehensive maintenance guide

More information

OPERATOR S MANUAL FOR MODEL BLADE GRINDER

OPERATOR S MANUAL FOR MODEL BLADE GRINDER OPERATOR S MANUAL FOR MODEL 88-021 BLADE GRINDER Table of Contents Page Blade Grinder Safety and User Instructions 2 Unpacking the Grinder 5 Assembling the grinder 6 Adjusting the grinding angle 8 Adjusting

More information

ARROW SAW PRECISE CUT 8000 RPM WITH DUST COLLECTING ATTACHMENT INSTRUCTION BOOK MODEL NO

ARROW SAW PRECISE CUT 8000 RPM WITH DUST COLLECTING ATTACHMENT INSTRUCTION BOOK MODEL NO ATTENTION If any components of this unit are broken or the unit does not operate properly, please contact Cabela s Customer Service. Retail Store Purchases: 1-800-905-2731 (U.S. & Canada) Catalog and Internet

More information

Installation Instructions Trektop NX

Installation Instructions Trektop NX Installation Instructions Trektop NX Vehicle Application: Jeep Wrangler Unlimited TJD 2004 2006 Part Number: 56821 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question. Click

More information

Tuff Tread. 502 W. Montgomery STE 120 Willis, TX PH: (800) FAX: (888)

Tuff Tread. 502 W. Montgomery STE 120 Willis, TX PH: (800) FAX: (888) Motor Brush Holder Assembly Installation Instructions Never use a sanding stone or comm stone on the commutator of a Noramco Fitness Treadmill motor. The commutator of a motor that has been properly broken

More information

User s Manual. A highly versatile chuck featuring easy to attach and release jaws for midi- and full-sized woodworking lathes

User s Manual. A highly versatile chuck featuring easy to attach and release jaws for midi- and full-sized woodworking lathes User s Manual Barracuda 5 Quick-Change Jaw System Chuck A highly versatile chuck featuring easy to attach and release jaws for midi- and full-sized woodworking lathes #CSCBARR5 IMPORTANT: Read this manual

More information

DASH KIT INSTALLATION

DASH KIT INSTALLATION ÿÿÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿ ÿÿÿ ÿÿÿÿÿ ÿÿ ÿÿÿ ÿÿÿÿÿÿÿÿÿÿÿÿÿÿ ÿÿÿÿÿÿÿÿÿÿ ÿÿÿÿ ÿÿÿÿ ÿÿ ÿÿÿÿÿ ÿÿÿÿÿÿÿÿ PROUDLY MADE IN THE USA DASH KIT INSTALLATION These instructions are aimed at the do-it-yourself installer. Read

More information

Page 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16

Page 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16 R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LACPACC-002 LACPACC-003 LACP-16TxxLP5 (0.5-in lead screw pitch) LACP-16TxxL1 (1-in lead screw pitch) C P I R K 4 ea Flanged

More information

675 Quick N Stall Neo Angle Framed Hinge Shower Enclosure

675 Quick N Stall Neo Angle Framed Hinge Shower Enclosure INSTALLATION INSTRUCTIONS 675 Quick N Stall Neo Angle Framed Hinge Shower Enclosure Call Technical Dept @ 1-800-452-2726 QCI1003 Page 1 of 9 Certified 10/01/09 INSTALLATION NOTES: Unpack your unit carefully

More information

Transform Cable Rail MUST be installed on 4" x 4" wooden posts sleeved with Transform post sleeves to support cable tension!

Transform Cable Rail MUST be installed on 4 x 4 wooden posts sleeved with Transform post sleeves to support cable tension! CABLE RAIL INSTALLATION INSTRUCTIONS OVERVIEW...2 LEVEL...3 STAIR...13 Transform Cable Rail MUST be installed on 4" x 4" wooden posts sleeved with Transform post sleeves to support cable tension! 1 Need

More information

SCION FR-S REAR SPOILER Preparation

SCION FR-S REAR SPOILER Preparation Preparation Part Number: PT938-18130-XX Kit Contents Item # Quantity Reqd. Description 1 1 Spoiler 2 2 Strut 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 M6 x 1 Nut with

More information

MANUAL TNS Series Nut Splitter

MANUAL TNS Series Nut Splitter TNS Series OPERATION AND MAINTENANCE MANUAL TNS Series Nut Splitter MODELS TNS-012, TNS-100, TNS-104, TNS-108, TNS-112, TNS-200, TNS-208, & TNS-300 1025 Conroy Place, Easton, PA. 18040 U.S.A. Phone: +1

More information

Chainsaws. Chainsaw engines need the regular maintenance covered in the rest of this course.

Chainsaws. Chainsaw engines need the regular maintenance covered in the rest of this course. Student Chainsaws Chainsaw engines need the regular maintenance covered in the rest of this course. All chainsaws use 2-stroke engines. These engines work hard in very dusty conditions. Check especially:

More information

Explorer Wiring Kit (assembled)

Explorer Wiring Kit (assembled) Explorer Wiring Kit (assembled) For Vintage, Firestorm & Standard Series Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers

More information

VARIABLE SPEED WOOD LATHE

VARIABLE SPEED WOOD LATHE MODEL MC1100B VARIABLE SPEED WOOD LATHE INSTRUCTION MANUAL Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Version: 2015.02.02

More information

INSTALLATION INSTRUCTIONS JEEP SCRAMBLER FAST TRAC TOP PART #108-21X

INSTALLATION INSTRUCTIONS JEEP SCRAMBLER FAST TRAC TOP PART #108-21X INSTALLATION INSTRUCTIONS JEEP SCRAMBLER FAST TRAC TOP PART #108-21X Thank you for purchasing Specialty s Convertible Top for your Jeep vehicle. It has been designed for great fit and long wear. Please

More information

ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE

ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE INSTALLATION INSTRUCTIONS ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE Copyright Alumax Bath Enclosures 2013. All rights reserved. G03980847 5-1-13 !WARNINGS! INSTALLATION WARNINGS a) Alumax Bath

More information

Fig Remove chain cover plate bolts. Fig Remove hammer member. Fig Loosen set screws at base of 12-tooth sprocket.

Fig Remove chain cover plate bolts. Fig Remove hammer member. Fig Loosen set screws at base of 12-tooth sprocket. Fig. 17.2. Remove chain cover plate bolts. Fig. 17.1. Remove hammer member. Fig. 17.3. Remove chain cover plate. Fig. 17.4. Loosen set screws at base of 12-tooth sprocket. Page 61 Fig. 17.5. Remove socket

More information

1/4 FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE 1400A-1700A-1800A

1/4 FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE 1400A-1700A-1800A 1/4 FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE 1400A-1700A-1800A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com

More information

Javelin Integra Inspired Design Precision Engineering

Javelin Integra Inspired Design Precision Engineering Javelin Integra Inspired Design Precision Engineering USER INSTRUCTIONS Thank you for choosing the Keencut Javelin Integra. Every effort has been made to bring you a precision engineered product with the

More information

INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5232

INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5232 INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5232 QCI5232 Rev 0 Page 1 Certified 06/20/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay

More information

PRODUCT: BALDUR + ODEN

PRODUCT: BALDUR + ODEN R INSTALLATION INSTRUCTIONS PRODUCT: BALDUR + ODEN CONFIGURATION: SINGLE DOOR MOUNT: GLASS MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com . TOOLS + MATERIALS REQUIRED

More information

TYPE 3740XL EXTRA LARGE WET RUNNING CARTRIDGE SPLIT SEAL

TYPE 3740XL EXTRA LARGE WET RUNNING CARTRIDGE SPLIT SEAL 1 Foreword These instructions are provided to familiarize the user with the seal and its designated use. The instructions must be read and applied whenever work is done on the seal, and must be kept available

More information

Frameless Bypass Slider

Frameless Bypass Slider INSTALLATION INSTRUCTIONS Frameless Bypass Slider QCI-5301 3/8 or 1/4 Glass Bypass Slider with Exposed Rollers QCI5301 Rev 1 Page 1 Certified 6/5/2017 Tools: To install your New Shower Enclosure, you may

More information

DX60 Block Plane 05P70.01

DX60 Block Plane 05P70.01 DX60 Block Plane 05P70.01 U.S. Des. Pat. D612,701 The body of this block plane by Veritas is ductile cast iron, a material much more durable as well as more stable than gray iron, having been fully stress

More information

Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide

Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide The following guidelines should be followed to lubricate the three main parts of the 400QMD mount. The QMD stands for Quartz Micro-Drive controller.

More information

Fixed Upper Sash Replacement Guide for Andersen 400 Series Woodwright Springline Single-Hung Windows

Fixed Upper Sash Replacement Guide for Andersen 400 Series Woodwright Springline Single-Hung Windows Fixed Upper Sash Replacement Guide for Andersen 400 Series Woodwright Springline Single-Hung Windows Manufactured Between September 2005 and October 2006 Read all instructions carefully before attempting

More information

Side and rear window, assembly overview

Side and rear window, assembly overview 64-7 Side and rear window, assembly overview 1 - Side/rear window Removing Unbroken Page 64-9 Broken Page 64-11 Installing Page 64-13 Curing time Page 64-21 Re-sealing Page 64-25 2 - PUR adhesive sealant

More information

Standard Kit #1 (5-way switch)

Standard Kit #1 (5-way switch) Standard Kit #1 (5-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable

More information

V-Groover SIMPLEX INSTRUCTION AND OPERATION MANUAL M O DEL 703. For best results use only authentic Logan blades.

V-Groover SIMPLEX INSTRUCTION AND OPERATION MANUAL M O DEL 703. For best results use only authentic Logan blades. www.logangraphic.com SIMPLEX M O DEL 703 INSTRUCTION AND OPERATION MANUAL For best results use only authentic Logan blades CAUTION: BLADES EXTREMELY SHARP Use replacement blades #1258 Logan Graphic Products,

More information

SECTION side windows round corners

SECTION side windows round corners 03-701.00/ 1 SECTION 03-701.00 2011SE08 GENERAL DESCRIPTION The windows installed on Nova vehicles may be a onepiece fixed type, or may consist of an upper and lower section, separated by a transom. The

More information

RAMPAGE P R O D U C T S. BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED

RAMPAGE P R O D U C T S. BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED RAMPAGE P R O D U C T S 84 (+/- 1/4 ) BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO 1966-1977 TOOLS REQUIRED 3/8 WRENCH 7/16 WRENCH ½ WRENCH #2 PHILLIPS SCREWDRIVER 1/8 DRILL BIT 9/64 DRILL BIT 5/32 DRILL

More information

Top spin Nr /

Top spin Nr / Top spin Nr. 1840 0000 / 1840 1000 Bedienungsanleitung 21-6680 28052014 / A Made in Germany Ideas for dental technology Top spin Nr. 1840 0000 / 1840 1000 Contents 1. Introduction...2 1.1 Symbols...2 2.

More information

R2C Performance Products 7550 Industrial Drive Forest Park, IL Ph: (708)

R2C Performance Products 7550 Industrial Drive Forest Park, IL Ph: (708) Congratulations on your purchase of the finest Sprint Car Filter and stack sealing system available. This system has been designed for unparalleled ease of assembly, disassembly and cleaning while providing

More information

In this step-by-step guide we will teach you how to. Your kit includes:

In this step-by-step guide we will teach you how to. Your kit includes: How to install your SSR speaker refoaming kit (View all of our DIY instructions by visiting www.springfieldspeakerstore.com and clicking on the DIY Instructions tab) In this step-by-step guide we will

More information

SETTING UP THE MODEL 210B-2 SRA

SETTING UP THE MODEL 210B-2 SRA SETTING UP THE MODEL 210B-2 SRA SAFETY PRECAUTIONS FOR THE MODEL 210B-2 SRA System Under Pressure: Shut off air supply and disconnect air hose before disassembling or disconnecting parts. Flying Debris:

More information

A socket contact support (supplied separately) must be installed onto the locator assembly.

A socket contact support (supplied separately) must be installed onto the locator assembly. Figure 1 PRO CRIMPER III Hand Tool Assembly 1976444 1 consists of PRO CRIMPER III Hand Tool Frame 354940 1 and Die Assembly 1976444 2. The tool assembly is used to crimp the contacts listed in Figure 1.

More information

ALWAYS TURN FIXTURE OFF/DISCONNECT POWER AND ALLOW TO COOL BEFORE PERFORMING ANY MAINTENANCE, INCLUDING RELAMPING AND CLEANING!

ALWAYS TURN FIXTURE OFF/DISCONNECT POWER AND ALLOW TO COOL BEFORE PERFORMING ANY MAINTENANCE, INCLUDING RELAMPING AND CLEANING! 100 Craftway, P.O. Box 128 Littlestown, Pennsylvania 17340-0128 Phone: 800-331-4185 Fax: 717-359-9672 INSTALLATION INSTRUCTIONS: S AND AREA/WALKWAY LISTED INSTRUCTION SHEET CONTENTS SHEET 1 SHEET 1 - General

More information

HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet

HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet Read the enclosed instructions and recommendations before any installations CONTENTS Dead-Length Collet Adaptation

More information

B-Too Drilling and Tapping Machine Instruction and Maintenance Manual

B-Too Drilling and Tapping Machine Instruction and Maintenance Manual B-Too Drilling and Tapping Machine Instruction and Maintenance Manual Thank you for your purchase of the B-Too Drilling and Tapping Machine. Please read and understand this short operation manual. Our

More information

ULTRA CUTTER PRO OPERATORS INSTRUCTION MANUAL. This manual covers all models 9, 11 and 13 HP

ULTRA CUTTER PRO OPERATORS INSTRUCTION MANUAL. This manual covers all models 9, 11 and 13 HP ULTRA CUTTER PRO OPERATORS INSTRUCTION MANUAL This manual covers all models 9, 11 and 13 HP Per OSHA 1926.503 it is the machine owner s responsibility to ensure that all workers using this Ultra Cutter

More information

#4500 BULLET SIZER & LUBRICATOR

#4500 BULLET SIZER & LUBRICATOR #4500 BULLET SIZER & LUBRICATOR Assembly Your new #4500 Bullet Sizer and Lubricator has been fully assembled at the factory, However, to facilitate packaging and shipping, the handle has been dismounted.

More information

INSTRUCTION BOOKLET AND WARRANTY INFORMATION 6 BENCH GRINDER

INSTRUCTION BOOKLET AND WARRANTY INFORMATION 6 BENCH GRINDER INSTRUCTION BOOKLET AND WARRANTY INFORMATION 6 BENCH GRINDER Part No.: SW1250 PLEASE READ CARE AND SAFETY INSTRUCTIONS BEFORE USE SPECIFICATIONS Part No.: SW1250 Input Voltage: 240V Frequency: 50Hz Rated

More information

Installation Instructions. Mesh Grille

Installation Instructions. Mesh Grille Installation Instructions Part Number 81114 I-sheet Rev. A1 Mesh Grille For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain

More information

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED RAMPAGE P R O D U C T S 84 (+/- 1/4 ) INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO 1966-1977 TOOLS REQUIRED 3/8 WRENCH 7/16 WRENCH ½ WRENCH #2 PHILLIPS SCREWDRIVER 1/8 DRILL

More information

Mechanical Frappe Press

Mechanical Frappe Press Mechanical Frappe Press Operation Manual CONTENTS OPERATIONAL INSTRUCTIONS PRECAUTIONS PART NAMES INCLUDED ITEMS BASIC OPERATION MAINTENANCE REPLACEMENT PARTS Thank you for using The Frapptastic Five Mechanical

More information

Repair Instructions ISC. Experience In Motion. ISC1PX Single Pusher Seal

Repair Instructions ISC. Experience In Motion. ISC1PX Single Pusher Seal Repair Instructions ISC ISC1PX Single Pusher Seal Experience In Motion These instructions are written for trained, experienced technicians familiar with the basic principles and tools involved in the installation,

More information

Frameless Inline Door With Return QCI5263

Frameless Inline Door With Return QCI5263 INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges

More information

Pressure Balance Shower Only Dual Control (Volume & Temperature) Ceramic Disc Cartridge Platinum Shower Trim Kit

Pressure Balance Shower Only Dual Control (Volume & Temperature) Ceramic Disc Cartridge Platinum Shower Trim Kit Shower Only PL8900-00 & TR-SH Pressure Balance Shower Only Dual Control (Volume & Temperature) Ceramic Disc Cartridge Platinum Shower Trim Kit - Installation Instructions Before Your Installation Read

More information

Side Rabbet Plane 05P44.01

Side Rabbet Plane 05P44.01 Side Rabbet Plane 05P44.01 U.S. Des. Pat. D596,475 The side rabbet plane is a specialty plane used for cleaning up or trimming the sidewalls of rabbets, dadoes or grooves to ensure a perfect fit with the

More information

VYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4

VYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4 VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7

More information

COYOTE ENTERPRISES, INC. RIMLOC BLAST WHEEL MAINTENANCE & ASSEMBLY MANUAL

COYOTE ENTERPRISES, INC. RIMLOC BLAST WHEEL MAINTENANCE & ASSEMBLY MANUAL COYOTE ENTERPRISES, INC. RIMLOC BLAST WHEEL MAINTENANCE & ASSEMBLY MANUAL Parts & Machinery for the Abrasive Blast Industry 27301 East 121st Street Coweta, Oklahoma 74429 (918) 486-8411 Fax (918) 486-8412

More information

15 Dovetail Jig. Instruction Manual. Part # 3452

15 Dovetail Jig. Instruction Manual. Part # 3452 15 Dovetail Jig Instruction Manual Part # 3452 CAUTION: Please read, understand, and follow all manufacturers instructions, guidelines and owners manuals that come with your power tools. Peachtree Woodworking

More information

SAFETY AND OPERATING MANUAL

SAFETY AND OPERATING MANUAL SAFETY AND OPERATING MANUAL 2 General Power Tool Safety Warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire

More information

Sailcloth Fabric Replacement Top and Doors Installation Instructions

Sailcloth Fabric Replacement Top and Doors Installation Instructions Sailcloth Fabric Replacement Top and Doors Installation Instructions For: Wrangler/TJ 1997-2002 Part Number: 79121 This product is only designed for the vehicles listed above. DO NOT INSTALL THIS PRODUCT

More information

CHRYSLER 300 CLUB Chrysler 300 Interior Door Star Emblem Replacement

CHRYSLER 300 CLUB Chrysler 300 Interior Door Star Emblem Replacement CHRYSLER 300 CLUB 1964 Chrysler 300 Interior Door Star Emblem Replacement Dec 2014 Rev 4. Congratulations! You have purchased one of the finest replacement emblems made for your 1964 Chrysler 300. Please

More information

Application Notes! RIGID MATERIALS. Rigid material standards. Printing on Rigid Materials with the Gerber Solara ion & Gerber CAT UV

Application Notes! RIGID MATERIALS. Rigid material standards. Printing on Rigid Materials with the Gerber Solara ion & Gerber CAT UV Printing on Rigid Materials with the Gerber Solara ion & Gerber CAT UV This document instructs on the proper use of rigid materials when printing on the flat bed of the Gerber Solara ion & Gerber CAT UV.

More information

Removing and Replacing the Y-truck

Removing and Replacing the Y-truck Service Documentation Removing and Replacing the Y-truck To remove and replace the Y-truck you will need the following tools: 4mm Allen wrench 12mm stamped flat wrench #2 Phillips screwdriver (magnetic

More information

INSTRUCTION MANUAL SM-330/ 430/ 936/ (Semi-Automatic Divider Rounder)

INSTRUCTION MANUAL SM-330/ 430/ 936/ (Semi-Automatic Divider Rounder) INSTRUCTION MANUAL SM-330/ 430/ 936/ 1136 (Semi-Automatic Divider Rounder) INSTRUCTION IMPORTANT INSTRUCTION THE INFORMATION IN THIS MANUAL IS CRUCIAL, MAKE SURE THAT THIS MANUAL HAS BEEN MADE AVAILABLE

More information

INFINITY-Z SHOWER DOOR / TUB DOOR INSTALLATION INSTRUCTION. MODEL #s 01-Chrome

INFINITY-Z SHOWER DOOR / TUB DOOR INSTALLATION INSTRUCTION. MODEL #s 01-Chrome INFINITY-Z SHOWER DOOR / TUB DOOR INSTALLATION INSTRUCTION IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical

More information