Installa on Guide: Fence Distributors. YourNextFence.com
|
|
- Erick Marshall
- 5 years ago
- Views:
Transcription
1 YourNextFence.com
2 Plan Your Fence each line by dividing the length of each line in inches by 96. Round any remainder up. 2
3 Calculate Materials * For standard single gates (46 1/4 opening) : (1) small Trex gate panel, (1) steel post insert, and (1) Trex single gate hardware kit. * For standard double gates (130 3/4 opening) : (2) large Trex gate panels, (2) steel gate post inserts, and (1) Trex double gate hardware kit. Tools Needed Before you begin Stakes Circular Saw String Line Drill you dig. Marking Paint Pencil Check local HOA and zoning laws Hammer Tape Measure Shovel Wheelbarrow 4 Level 12 Miter Saw which may regulate the height and placement of your fence. Apply for local permits as directed by local code. Post Hole Digger Digging Bar Speed Square Finish Nail gun eyes and ears. For a step by step installa on video, visit: 3 3
4 Exploded View B C D E A C C A. 1 Post B. 1 Post Cap C. 4 Fence Brackets D. 1 Top Rail F E. 19 Pickets F. F G C G. 4
5 Step 1: Determine Install Method 1. Step Method: This method gradually steps up the slope and the rails remain level. This may leave gaps under the fence. The downhill post will need to be set taller. Longer posts may be required. When laying out the fence post spacing, measure on a level line from one post to another. 2. Following the Grade: This method follows the grade or slope with the rails parallel to the ground. The post spacing may need to be reduced to avoid rails being too short because of the angle. 3. The fence can different height. Post spacing will need to be reduced. Pickets will need to be cut to height. 5 5
6 Step 2: Stake and String pins so that stakes will not be disturbed when digging holes, and approx. 4-5 inches inside of property pins to insure no encroaching on neighbors. 2. string every 96 2 in from the string to mark center of hole (see Fig. 1). Notes: Laying out posts ) on center. 96 centers. o 90.2 (68 x 12 = 812 / 9 = Fig. 1 6
7 Step 3: Dig Holes 1. Dig holes for the posts making sure not to disturb the stakes for the string. The string may be removed and replaced a er holes are dug. The holes should be approximately 12 diameter and 30 deep (depending on local codes). Holes should be dug so that they allow equal amounts of concrete on all sides of posts ( ee ig. 2) Fig. 2 Step 4: Set Posts 1. Plumb and level each post to the string line using a post level or 4 level* Make sure that the posts are next to but not pushing the string line. Fill the hole with concrete and brace if necessary un l concrete is cured. low concrete to dry hours (depending on temperature) before building. This line is pulled posts to set line post is pulled to keep the post in line. Fig. Fig. 4 *Note: If se ng posts to height begin by se ng all end, corner and transi on (post w ere grade changes) posts first. Posts should be 74 1/2 inches high**. String a line from the top of these posts set the remainder of the posts to the height of the string. (see ig. 4) **Refer to page 14 for measurements for fence heights other than
8 Step 5: Cut Posts 1. Cut the tops of the posts f posts not set to height ark all end, corner and transi on posts at 74 1/2 * ** above grade and string a line from these post ( ig. ) ark all posts and cut to the height of the string using a circular saw. Fig. 5 Typical Post Reve l If greater reve l is desired increase post height. **Refer to page 14 for measurements for fence heights other than 6. 8
9 Using 1 5/8 fence screws, a ach the Fence brackets to the post as follows: A ach a bracket* 5 3/4 down from the top of the post. A ach a bracket 73 5/8 ** down from the top of the post (see ig. ) If the fence is on a slope, the brackets on the downhill side will need to be lowered so that the rails flow smoothly. 5 3/4 Fig. 73 5/8 74 1/2 *Note: For angles use angle adaptors with the fence brackets. Each adapter provides a 22.5 of adjustment **Refer to page 14 for measurements for fence heights other than
10 Mark the aluminum bo om rail, bo om rail covers, and top length by holding them next to the post.* (see ig. ) for Cut the aluminum bo om rail with a nonferrous metal cu ng blade. Cut the aluminum 1/2 shorter (do not cut the bo om rail covers shorter) to avoid scratching the post during installa on. If the distance between posts is 91 the aluminum rail will not need to be cut. Cut top rail and bo om rail covers with miter saw Set the top rail in place over the brackets. Leave the rail in place while marking and cu ng the remaining rails, to ensure all rails fit properly. Slide the bo om rail covers over the aluminum bo om rail as shown (see Fig. 8). Place the assembled bo om rail over the bo om brackets with the deeper channel facing down. Fig. Fig. deeper channel over bo om brackets 10
11 Step 8: Install Pickets Cut two pickets to a ach to the posts an each end. The picket sits inside the aluminum rail and should be cut to fit just below the top bracket (see Fig. 9). Insert the first picket into the aluminum rail, and secure it to the post using three 1 5/8 exterior screws (see Fig. 10). If the posts are set at 8 on center, the first and last picket will face the same direc on. For shorter sec ons, the first and last pickets may face in opposite direc ons. Insert pickets into the bo om rail, alterna ng their orienta on so they interlock (see Fig 1 ) If the last picket is ght t may be easier to remove the second to last picket and reinsert it by sliding it down from above a er the last picket is screwed to the post (see ig. 1 ) Fig. Fig. 1 Fig. 1 Fig. 1 11
12 Step 9: Install Top Rail and Secure Pickets by star ng at one end and se ng the rail over one fence bracket gradually lowering over the pickets. Secure the top rail to the fence brackets using 1 5/8 exterior screws through the top of the rail at each end (see Fig. 1 ) Fig. 1 If the pickets are not all interlocked ghtly: ull all of the pickets ght towards one post (see ig 1 ). Secure the third to the last picket through the top and bo om rails with finish nails or composite screws (see Fig 1 ) Fig. 1 Fig
13 3. venly space the last picket (see ig. 1 ) and secure it through the top and bo om rails with fasteners (finish nails or composite screws) (see Fig. 17). Place addi onal fasteners through every other pioket to prevent ra ling. Fig. 1 Fig. 4. Place post cap onto the post and secure using adhesive or finish nails (see Fig. 18). Fig. 1 For a step by step installa on video, visit:
14 Trex Seclusions (all heights) 14
15 Install Single Gate A. Fence posts B. Gate Panel C. E. Gate Latch F. Gate Striker G. Gate Handle D. Gate Hinge 10 15
16 Step 1: Set the Single Gate Posts A. * faces away from gate opening. B. Set posts into post holes. Hole Dimensions for standard gate openings are 30 deep by 12 wide. However, con- C. The opening (measuring from the inside face of one post to inside face of the other post) for a standard size Trex Seclusions Gate panel should be 46 1/4. Inside faces of posts should be parallel with each other. (**The opening for a standard Large Size Trex Gate panel is 65 3/4 wide) Custom heights and widths are available. Note: Due to concrete cure -3 days before gate is installed. *Note: If the Hinge Post is not connected to a fence panel or if a large gate panel is used it may be necessary to use a Heavy 16
17 Step 2: Install the Gate Panel A. Using a 3/8 6 1/2 selfdrilling screws. Pre-drilling with a 3/16 B. Place the gate panels in the opening. Adjust the gates so that the top rail lines up with the top rail of the fence. C. Using the supplied 1 1/2 self- D. hinge bracket to the hinge post. D 6 x4 A B C x
18 1. 36 from the ground (or to desired height) using the supplied 1 1/2 self-drilling screws. The latch should be oriented so the catch is on the gate-swing side of the post. The catch will face up or A 2. Using the supplied 1 1/2 selfto the gate panel, lining the striker rod up with the catch on the post latch. Gate swing Catch 3. Catch B gate panel upright, using the supplied 1 self-drilling screws. Han- 3/4 from the edge of the gate panel. Gate swing x4 C The height must be staggered. Step 4: Make any Final Adjustments 1. T 11/16 wrench Due to weather and temperature changes, periodic hinge adjustment may be necessary to as- 18
19 Install Double Gate A. Fence post B. Gate Panel C. D. Gate Hinge E. Gate Latch F. Gate Striker G. Gate Handle H. Drop Rod B2 B1 H BACK SIDE OF B2 6 19
20 Step 1: Set the Double Gate Posts A. * opening. B. Set posts into post holes. Hole Dimensions for standard gate openings are 30 deep by 12 wide. However, consult local condepth. C. The opening (measuring from the inside face of one post to inside face of the other post) for a standard size Trex Seclusions Gate panel should be 91 1/2 wide**. The Inside faces of posts should be parallel with each other. (**The opening for a double gate using standard Large Size Trex Gate panels is 130 1/2 wide) Custom heights and widths are available. Note: Due to concrete cure -3 days before gate is installed. *Note: If the Hinge Post is not connected to a fence panel or if a large gate panel is used it may be necessary to use a Heavy. 20
21 Step 2: Install the Gate Panel A. Using a 3/8 6 1/2 self-tapping Screws. Pre-drilling with a 3/16 B. Place the gate panels in the opening. Adjust the gates so that the top rails line up with each other and with the top rail of the fence. C. Using the supplied 1 1/2 self- D. hinge post. D 6 x4 A B C x
22 1. - only one panel is in use) approximately 36 from the ground (or to desired height) using the supplied 1 1/2 self-drilling screws. The latch should be oriented so the catch is on the gate-swing side of the post. The catch will face up or down depend- A Gate swing 2. Using the supplied 1 1/2 selfthe gate panel, lining the striker rod up with the catch on the post latch. Catch 3. Catch B panel upright, using the supplied 1 self-drilling screws. Handles should 3/4 from the edge of the gate panel. The height must be Gate swing x4 C staggered. Step 4: Make Any Final Adjustments 1. T 11/16 wrench Due to weather and temperature changes, periodic hinge adjustment may be necessary to as- 22
23 Step 5: Mount the Drop Rod A. - Reverse the drop rod brackets depending on which side of the gate the drop rod is to be mounted. B. 3 from the 2 self-drilling screws on the inside edge of the gate panel upright and 1 self-drilling screw on the face of the gate pan- 14 from the C. 24 el and 2 to the center of the screw holes from the edge of the gate panel. A. D. where the drop rod hits. If the gate is over a concrete pad, drill an 8 deep hole using a 3/4 masonry bit for the drop rod to slide into when the gate is closed. For gates over soil, dig a hole 8 wide x 18 deep below the rod, fill it with concrete, and insert an 8 long 3/4 PVC pipe in the concrete for the drop rod to slide B. 2 C
24 TM Care And Maintenance Clean fence to remove dirt and debris. Soap, hot water and a so brush are all that needed Water Spots, Leaf Staining and Wood Tannins Scuffs & Abrasions Rust Stains, Ground-In Dirt and Grime and Pigment Staining Oil and grease Stains Mold & Mildew Pressure Washer Sanding Disposal Trex Company does not recommend sanding. Sanding will change the appearance of the surface of Trex Material and will void the warranty. Do not burn Trex products. Trex is a federally registered trademark of Trex Company, Inc., Winchester, Virginia. Horizons COMPOSITE FENCING SYSTEM is an exclusive product and trademark of FDS Distributors, Inc., Provo, Utah. Contact us YourNextFence.com Sales@YourNextFence.com 15
Installa on Guide: Fence Distributors. YourNextFence.com
TM YourNextFence.com Plan Your Fence each line by dividing the length of each line in inches by 97. Round any remainder up. 2 Calculate Materials Tools Needed Stakes Circular Saw String Line Drill Marking
More informationInstallation Guide: Fence
N Installation Guide: Fence Visit trexfencing.com Trex Horizons Fencing www.trexfencing.com PLESE RE REFULLY Trex Horizons Fence olors Saddle Woodland rown Winchester Grey* *When it is new, Winchester
More informationUNIVERSAL PANEL AND GATE
PVC Fencing / Residential Style UNIVERSAL PANEL AND GATE INSTALLATION INSTRUCTIONS Fencing Without Boundaries TM 1 BEFORE YOU START, IT S IMPORTANT TO CHECK......That fence footings do not exceed legally
More informationFENCE INSTALLATION GUIDE 8 HIGH WALLS
FENCE INSTALLATION GUIDE 8 HIGH WALLS 1.866.648.9336 www.simtekfence.com INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers of SimTek decorative
More informationRanch Rail Vinyl Fence
Ranch Rail Vinyl Fence INSTALLATION INSTRUCTIONS These instructions are to be used as general guidelines for the installation of your vinyl fence under normal installation conditions. Local conditions
More informationCertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS. Fence Installation Guide 3', 4' & 6' High
CertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS Fence Installation Guide 3', 4' & 6' High INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers
More informationSEMI-PRIVACY PANEL AND GATE INSTALLATION INSTRUCTIONS
SEMI-PRIVACY PANEL AND GATE INSTALLATION INSTRUCTIONS 1 BEFORE YOU START, IT S IMPORTANT TO CHECK: That fence or the fence post footings do not exceed your lot lines of your property. If you can locate
More informationSECTION 19: Endwood Fusion Welded Gate Installation Guide
SECTION 19: Endwood Fusion Welded Gate Installation Guide ASSEMBLY AND INSTALLATION FOR: Fusion Welded Gates Gate Frame with Full Size Pickets Privacy & Board on Board California & Shadowbox Gate width
More informationInstallation Instructions. Tools Needed. Tape measure. Level. Shovel or Post hole digger. Concrete. Drill. Stakes. Mallet or hammer.
Installation Guide EcoStone Fence 1330 West 400 North Orem, UT 84057 Toll Free 1.866.648.9336 Tel. 1.801.655.5236 Fax 1.801.655.5240 www.ecostonefence.com Installation Instructions Introduction. These
More informationOPEN PICKET PANEL AND GATE INSTALLATION INSTRUCTIONS
For All Your Vinyl Fencing Needs OPEN PICKET PANEL AND GATE INSTALLATION INSTRUCTIONS 1 BEFORE YOU START, IT S IMPORTANT TO CHECK: That fence or the fence post footings do not exceed your lot lines of
More informationPRIVACY FENCE WITH LATTICE INSTALLATION INSTRUCTIONS
PRIVACY FENCE WITH LATTICE INSTALLATION INSTRUCTIONS These instructions are to be used as general guidelines for the installation of your vinyl fence under normal installation conditions. Local conditions
More informationFENCE INSTALLATION GUIDE 6 HIGH FENCE
FENCE INSTALLATION GUIDE 6 HIGH FENCE 1.866.648.9336 www.simtekfence.com INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers of SimTek decorative
More informationPRIVACY FENCE WITH SCALLOPED PICKET INSTALL INSTRUCTIONS
PRIVACY FENCE WITH SCALLOPED PICKET INSTALL INSTRUCTIONS These instructions are to be used as general guidelines for the installation of your vinyl fence under normal installation conditions. Local conditions
More informationTRADITIONAL & SCALLOP PICKET INSTALLATION INSTRUCTIONS
TRADITIONAL & SCALLOP PICKET 1 WHAT YOU LL NEED TO INSTALL POWER AUGER OR POST HOLE DIGGER(CLAMSHELLS) SHOVEL DIGGING BAR (OPTIONAL) BRIGHT COLORED SPRAY PAINT STRING LINE STAKES AND LEVEL CORDLESS OR
More informationInstallation Guide. Capped Cellular PVC Fencing. Table of Contents. Storage and Handling Tools Needed Fence Layout and Locating Posts
Capped Cellular PVC Fencing Installation Guide Table of Contents Storage and Handling Tools Needed Fence Layout and Locating Posts Installation instructions 4 x 4 Over Sleeve Post - 3.5 Rail Privacy Shadowbox
More informationGood Neighbour INSTALLATION GUIDE GOOD NEIGHBOUR FENCING BEFORE YOU START TOOLS AND HARDWARE REQUIRED
INSTALLATION GUIDE Good Neighbour GOOD NEIGHBOUR FENCING Stratco Good Neighbour fencing is both strong and attractive. Its design allows clean and uncluttered lines to be enjoyed by neighbours on both
More informationResidential Fencing Picket. Installation Guide
Residential Fencing Picket. Installation Guide Jabiru Picket Fence White Contents Getting Started 4 Installation Tips 4 Shortening a Panel Tools Required 5 Instructions 6 3 Getting Started Congratulations
More informationTREX fencing. form + function = fabulous trex fencing Trex Seclusions and Trex Surroundings
TREX fencing form + function = fabulous trex fencing Trex Seclusions and Trex Surroundings A Trex fence. How neighborly. Whether the goal is privacy, safety or a stunning garden backdrop, a Trex fence
More informationPRO-RIB FENCE PANELS INSTALLATION GUIDELINES. Virtually Maintenance Free Available in 24 Colors Custom Heights Available by the Inch
PRO-RIB FENCE PANELS INSTALLATION GUIDELINES Virtually Maintenance Free Available in 24 Colors Custom Heights Available by the Inch www.midwestmanufacturing.com Page 2 TOOLS NEEDED Measuring Tape Drill
More information6a. Eight Steps to Chain-Link Fence Installation
6a. Eight Steps to Chain-Link Fence Installation Before You Start You will need the following tools to install your chain-link fence: Post hole digger Wheelbarrow, shovel and hoe for mixing concrete Tape
More informationPRIVACY INSTALLATION FOR: Standard 6 H x 8 W Privacy Fence 4 x 4 Post Sleeve & Brackets Dog Ear or Straight-Edge Pickets 1.75 x 3.
PRIVACY INSTALLATION FOR: Standard 6 H x 8 W Privacy Fence 4 x 4 Post Sleeve & Brackets Dog Ear or Straight-Edge Pickets 1.75 x 3.5 Rail Storage and Handling Fence Preparation and Layout Locate and Set
More informationAluminum Pre-Built Fence For Standard & Heavy-Duty Series
ALUMFENCEA-BOM Aluminum Pre-Built Fence For Standard & Heavy-Duty Series INSTALLATION INSTRUCTIONS Read all instructions prior to installing product. Refer to manufacturers safety instructions when operating
More informationSHADOWBOX INSTALLATION FOR: Standard 6 H x 8 W Shadowbox Fence 5 x 5 Routed Posts Dog Ear or Straight-Edge Pickets 1.75 x 3.5 Rail
SHADOWBOX INSTALLATION FOR: Standard 6 H x 8 W Shadowbox Fence 5 x 5 Routed Posts Dog Ear or Straight-Edge Pickets 1.75 x 3.5 Rail Storage and Handling Fence Preparation and Layout Locate and Set Posts
More informationALUMINUM FENCE. Additional freight charges may apply depending on order size. Please call for quote at
ALUMINUM FENCE Additional freight charges may apply depending on order size. Please call for quote at 1-888-662-1788 Powder Coat Finish FORGERIGHT Fences are offered in the choice of three colors: Black,
More informationRANCH RAIL FENCE INSTALLATION INSTRUCTIONS
1 WHAT YOU LL NEED TO INSTALL POWER AUGER OR POST HOLE DIGGER(CLAMSHELLS) SHOVEL DIGGING BAR (OPTIONAL) BRIGHT COLORED SPRAY PAINT STRING LINE STAKES AND LEVEL CORDLESS OR POWER DRILL WITH DRILL AND SCREW
More informationINSTALLATION MANUAL. 2. Check with local utility companies for locations of underground cables or pipe lines.
INSTALLATION MANUAL Install our maintenance free fencing system yourself! About 90% of our residential clientele install our fencing systems themselves. Why hire and pay someone to install it when you
More informationGOOD NEIGHBOUR FENCING INSTALLATION GUIDE GOOD NEIGHBOUR FENCING BEFORE YOU START TOOLS AND HARDWARE REQUIRED
GOOD NEIGHBOUR FENCING Stratco Good Neighbour fencing is both strong and attractive. Its design allows clean and uncluttered lines to be enjoyed by neighbours on both sides of the fence. Good Neighbour
More informationIMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS PACKED INSIDE.
ASSEMBLY GUIDE Newport Vinyl Picket Fence with Post and No-Dig Steel Pipe Anchor Kit (6 H x 7 W) 68 / in /6 in 6 in / in 7/8 in 8 / in 6 in in Ground 4 in This fence can easily be trimmed down horizontally
More informationFence System Components
Fence System Components Line Post Interior Flat Exterior Flat Gothic Caps Section Top Rail Picket Exterior Ball New England Bottom Rail Corner Post End/Gate Post Gate 3/4" ON EACH SIDE ADJUSTABLE NYLON
More informationINSTALLATION MANUAL. 2. Check with local utility companies for locations of underground cables or pipe lines.
INSTALLATION MANUAL Install our maintenance free fencing system yourself! About 90% of our residential clientele install our fencing systems themselves. Why hire and pay someone to install it when you
More informationVinyl Fence and Railing
Vinyl Fence and Railing WHY PRO ELITE & PRO GUARD VINYL? Virtually maintenance free Weather resistant Safe, strong, durable, and ideal for all climates No painting, sanding, or maintenance required Easy
More informationT r e x Art i s a n Se r i e s Railing
T r e x Art i s a n Se r i e s Railing I n s t a l l a t i o n In s t ru c t i o n s Trex Railing Components A. Trex Top Rail B. Trex Bottom Rail C. Trex Railing Support Bracket D. TrexExpress Railing
More informationInstallation Fence Guide Kodiak Iron. Exceptional Fencing Extraodinary Customer Service
Installation Fence Guide Kodiak Iron Exceptional Fencing Extraodinary Customer Service Kodiak Fence System Installation Guide Thank you for the purchasing the Kodiak Fence System. Fence installation is
More informationVinyl Fence Installation Instructions. Privacy Fence Installation Instructions
Privacy Fence Installation Instructions Tips Before You Start - Read this instruction sheet completely. - During fence assembly, work on a soft, non-abrasive surfaces where possible to avoid - scratching
More informationFENCE INSTALLATION GUIDE 3, 4, & 6 HIGH FENCE
FENCE INSTALLATION GUIDE 3, 4, & 6 HIGH FENCE 1.866.648.9336 www.simtekfence.com INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers of SimTek
More informationFlex Fence Instruction Manual
The Safer Stronger Smarter Choice Flex Fence Instruction Manual Table of contents 2 3 4 4 5 5 6 7 8 10 10 11 11 12 13 13 15 18 18 19 20 22 Table of contents Supplies, tools and equipment Introduction Laying
More informationPost & Rail Crossbuck
Post & Rail Crossbuck 1. Getting Started 6. Crossbuck Be sure to call underground prior to digging Assemble gates (if necessary) and decide where they will be located Stake out the fence line Space and
More informationASPEN STYLE. ORNAMENTAL GATE INSTALLATION GUIDE 3 Rails, Pressed Top/Flat Bottom Model No. EGBR5842-N2P
1 ASPEN STYLE ORNAMENTAL GATE INSTALLATION GUIDE 3 Rails, Pressed Top/Flat Bottom Model No. EGBR5842-N2P INSTALLATION VIDEO AVAILABLE AT: video01.xcelfence.com Item Description Gate installation and assembly
More informationInstallation Instructions for. Before You Begin TOOLS REQUIRED
Composite Railing System STEP-BY-STEP Installation Instructions for Spectrum Composite Railing Virtually maintenance free 20-year warranty EverNew Spectrum Railing system is designed to work with a number
More informationPVC Fencing Install Instructions
PVC Fencing Install Instructions Step 1-Pounding the Galvanized Steel Posts Call your local area utility company to come mark underground lines before any digging or pounding any posts into the ground.
More informationCXT PRO RAILING INSTALLATION INSTRUCTIONS For Installations Using Aluminum and Glass Balusters Sold Separately
CXT PRO RAILING INSTALLATION INSTRUCTIONS For Installations Using Aluminum and Glass Balusters Sold Separately CCRR-0171 PFS AA-652 Drill/power screwdriver Assorted drill bits Hammer Miter or circular
More information10 x 10 Flat Top Two Tone Pergola
0 x 0 Flat Top Two Tone Pergola Models: Bordeaux ASSEMBLY GUIDE OPTIONAL ACCESSORIES Arch Kit System ( Arches) Privacy Fence Panel System ( Panels & Middle Post) Bolt Down Bracket Kit ( for Pergola) Ver.0-00
More informationDecorative Driveway Gate Installation Manual
Decorative Driveway Gate Installation Manual Installation Instructions for All Single and Dual Gate Kits IMPORTANT: Before digging the holes for your installation, be sure to contact the appropriate utility
More informationQwik-Fence Installation Instructions
Qwik-Fence Installation Instructions 1 Tools Required The following installation instructions should be used as a guide for installing Folding Guard Qwik-Fence Partitions. Good common sense and appropriate
More information10 x 10 Arch Top Pergola
0 x 0 Arch Top Pergola I N S T A L L A T I O N G U I D E O P T I O N A L A C C E S S O R I E S Privacy Fence Panel System ( Panels & Middle Post Included) Bolt Down Bracket Kit (Set of ) Additional Shade
More informationINSTALLATION MANUAL FACE MOUNT FOR DOG-EAR & SQUARE TOP PICKETS. STYLE BOARD ON BOARD (Privacy) SHADOWBOX (Semi-Private) TRADITIONAL (Semi-Private)
STYLE BOARD ON BOARD (Privacy) SHADOWBOX (Semi-Private) TRADITIONAL (Semi-Private) INSTALLATION MANUAL FACE MOUNT FOR DOG-EAR & SQUARE TOP PICKETS Questions, problems, missing parts? Before returning to
More informationInstallation Guide. Step-by-Step Guide
Installation Guide Step-by-Step Guide Thank you for choosing one of our quality products. We are the industry leaders in designer panel fencing. This product will provide you with years of trouble free
More information6 1/2 x 6 1/2 Flat Top Pergola
6 / x 6 / Flat Top Pergola A S S E M B L Y G U I D E Models: Portland, Liberty O P T I O N A L A C C E S S O R Y Bolt Down Bracket Kit V.-0506 Ta b l e o f Co n t e n t s PAGE The Introduction & Overview......................................................
More informationCottage Picket Gate. 6 in in in in
S S E M LY I N S T R U T I O N S www.newenglandarbors.com ottage Picket Gate 1.875 in 6 in 43.75 in 22.5 in 2 48.5 in Please read through before starting assembly. heck ox for These ontents (1 ox) In the
More informationPost & Rail. Includes: Crossbuck, 2-Rail, 3-Rail and 4-Rail POST SUPPORT OPTIONS
Post & Rail Includes: Crossbuck, 2-Rail, 3-Rail and 4-Rail STAGGER RAIL ENDS FOR GREATER STRENGTH ALLOW 1-1/2" GAP ON HINGE SIDE OF GATE AND 1-1/4" ON LATCH SIDE OF GATE HARDWARE DIG HOLES 30" MINIMUM
More informationPlain Jane Vinyl Gate REALLY. Important stuff to know about installing your WamBam gate
Plain Jane Vinyl Gate RELLY Important stuff to know about installing your WamBam gate. 1-877-778-5733 www.wambamfence.com CLEVER JOE Your Installation Buddy 02.2017 Reality Check 1 - Read Over Fence Instructions
More informationVINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS
P a g e 1 VINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS Shown: 8' x 12' Vinyl Classic Pergola with 12" Top and Main Runner Spacing The design of this pergola is based on all posts being installed
More informationINSTALLATION MANUAL BRACKET MOUNT FOR DOG-EAR PICKETS & SQUARE TOP PICKETS
STYLE BOARD ON BOARD (Privacy) SHADOWBOX (Semi-Private) TRADITIONAL (Semi-Private) INSTALLATION MANUAL BRACKET MOUNT FOR DOG-EAR PICKETS & SQUARE TOP PICKETS Questions, problems, missing parts? Before
More informationFENCES AND GATES
FENCES & GATES 32 31 00 Natures Composites NATURES COMPOS TES fence. deck. landscape. TM Natures Composites 1302 Industrial Park Ave. Torrington, WY 82240 Tel: 307-532-9942 Fax: 307-532-9943 Email: jw@naturescomposites.com
More informationVinyl Fence Products. Installation Guidelines. Hyde Park with H-Post Fence
Vinyl Fence Products Installation Guidelines Hyde Park with H-Post Fence Hyde Park with H-Post Privacy Fence 1. Getting Started Be sure to call underground prior to digging Assemble gates (if necessary)
More information1. Layout. Step 1. Step 2. Step 3. Fig. 1
1-3/8 Panel Clamp Tools You Will Need: Tape Measure, Mason s String, Stakes, Hole Digger, Shovel, Level, Wheelbarrow, Wrenches or Adjustable Wrench, Hacksaw, Pliers, Cutting Pliers, Fence Stretcher and
More informationAFCO-Rail Post INSTALLATION INSTRUCTIONS AFCO-RAIL POST
AFCO-Rail Post INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Drill Bits (for the appropriate fastener) Drill (with adjustable clutch, recommended) Level String Line Tape Measure Tools to install fasteners
More informationThe following instructions will guide you through the installation of your new vinyl railing stair kit.
Installation Guide Vinyl Standard Stair Railing Tools Required Protective eye glasses Tape measure Variable speed drill/screwdriver Rotary hammer or hammer drill and masonry percussion bit recommended
More informationNervous Nelly Vinyl Gate REALLY. Important stuff to know about installing your WamBam gate
Nervous Nelly Vinyl Gate RELLY Important stuff to know about installing your WamBam gate. 1-877-778-5733 www.wambamfence.com CLEVER JOE Your Installation Buddy 02.2017 Reality Check 1 - Read Over Fence
More information10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.0-7 Table of Contents PAGE Introduction & Overview...................................................... Pergola Materials Overview..............................................................
More informationASPEN STYLE. ORNAMENTAL FENCE INSTALLATION GUIDE 3 Rails, Pressed Top/Flat Bottom Model No. NBR7958-NPF
1 ASPEN STYLE ORNAMENTAL FENCE INSTALLATION GUIDE 3 Rails, Pressed Top/Flat Bottom Model No. NBR7958-NPF INSTALLATION VIDEO AVAILABLE AT: video01.xcelfence.com Item Description Fence installation and assembly
More informationMurphy Door DIY Hardware Installation Manual
Murphy Door DIY Hardware Installation Manual The Murphy Door Bi-Folding Bookshelf was designed to install IN FRONT of existing door ways, replacing the door or doors while concealing the door way. In MOST
More informationBefore You Begin IMPORTANT. Always wear safety glasses when cutting and drilling railing or decking products.
Before You Begin IMPORTANT Always wear safety glasses when cutting and drilling railing or decking products. HELPFUL HINTS Use carbide-tipped, multi-purpose blade for cutting. Do not lay components on
More information12 x 12 Flat Top Pergola
x Flat Top Pergola Model: Regency, Roosevelt ASSEMBLY GUIDE OPTIONAL ACCESSORIES: Bolt Down Bracket Kit Canvas Weave Shade Kit Privacy Wall Pergola Planter ( for Pergola) (Regency Only) (Regency Only)
More information10 x 10 Flat Top Pergola
0 x 0 Flat Top Pergola A S S E M B L Y G U I D E Models: Venetian, Tuscany, Luxor, Acadia O P T I O N A L A C C E S S O R I E S Arch Kit System ( Arches) Privacy Fence Panel System ( Panels & Middle Post)
More informationInstallation Instructions for. Handrail Component System
Handrail STEP-BY-STEP Installation Instructions for Handrail Component System Rise in Inches Run in Inches 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 13.5 14 14.5 15 8.5 47 45 43 42 40 39 38 36 35 34 33 32
More informationMODERN PERGOLA INSTALLATION GUIDE. When only the best will do.
MODERN PERGOLA INSTALLATION GUIDE When only the best will do. TOOLS LIST Drill(s) 3/8" Magnetic Driver (s) 12" Drill Extension #2 Square Drive bit for Drill or Driver Level Tape Measure Hammer Drill if
More informationINSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS.
INSTALLATION INSTRUCTIONS FOR REPLACEMENT FORGENT WOOD GLASTRA WINDOWS RECOMMENDATIONS FOR COMMON INSTALLATION OF ALL REPLACEMENT WINDOWS. Installer: DO NOT DISCARD Please leave the Installation Guide
More informationINSTALLATION MANUAL BRACKET MOUNT FOR DOG-EAR PICKETS & SQUARE TOP PICKETS
STYLE BOARD ON BOARD (Privacy) SHADOWBOX (Semi-Private) TRADITIONAL (Semi-Private) INSTALLATION MANUAL BRACKET MOUNT FOR DOG-EAR PICKETS & SQUARE TOP PICKETS Questions, problems, missing parts? Before
More informationINSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS.
INSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS. Installer: DO NOT DISCARD Please leave the Installation Guide with the home owner
More informationCertainTeed. Vinyl Fence Installation Guidelines. Routed Rails and Posts. Heavyweight Pickets. Steel Reinforced Bottom Rail
CertainTeed Vinyl Fence Installation Guidelines Table of Contents System Components 1 Tools and Materials 2 General Information 3 Assembling Sections Traditional Picket Fence Cape Cod, Yorkshire 4-5 Danbury,
More informationManchester Vinyl Picket Gate with Posts (42 Wide x 42 Tall)
ASSEMBLY INSTRUCTIONS Manchester Vinyl Picket Gate with Posts (4 Wide x 4 Tall) /4 in / in 4 in 6 in 45 /8 in 4 in 8 in 4 / in Gate Opening in Ground 49 / in Outside Posts This Gate is designed to be integrated
More informationCottage Picket Gate A S S E M B LY I N S T R U C T I O N S
S S E M LY I N S T R U T I O N S ottage Picket Gate 1 7/8 6 43 3/4 22 1/2 48 1/2 Please read through before starting assembly. heck ox for These ontents (1 ox) In the event of missing or defective parts
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationPORCH RAIL INSTALLATION INSTRUCTIONS. Level Rail... 2 Stair Rail... 8 Care & Maintenance, Finishing... 15
PORCH RAIL INSTALLATION INSTRUCTIONS Level Rail... 2 Stair Rail... 8 Care & Maintenance, Finishing... 15 COMPONENT LIST LEVEL RAIL KIT Porch Rail was designed to meet the most stringent building codes.
More informationLenox Slide Lock Pergola
ASSEMBLY GUIDE Models: Lenox OPTIONAL ACCESSORIES Bolt Down Bracket Kit ( for Pergola) Ver.0-076 Table of Co n t e n t s Introduction & Overview...................................................... Pergola
More informationTwo Panel Frameless Bypass Door
INSTALLATION INSTRUCTIONS Two Frameless Bypass Door Series 00 Please Record Model Number From Carton Label Here Please read these instructions carefully to familiarize yourself with the required tools,
More informationPORCH-LOC INSTALLATION INSTRUCTIONS
PORCH-LOC INSTALLATION INSTRUCTIONS 2017 HB&G Building Products, Inc. Porch-Loc Installation Instructions NOTE: DISCARD THE INSTALLATION INSTRUCTIONS AND HARDWARE THAT CAME IN YOUR PERMAPOST PACKAGING
More informationSteady Freddy Vinyl Gate REALLY. Important stuff to know about installing your WamBam gate
Steady Freddy Vinyl Gate RELLY Important stuff to know about installing your Wamam gate. 1-877-778-5733 www.wambamfence.com CLEVER JOE Your Installation uddy This Gate is lso Designed to Fit the ig en
More informationRAILING. Installation Guide
RAILING Installation Guide THE BEST CHOICE FOR STRONG & DURABLE RAILING SYSTEMS Our exclusive manufacturing process ensures our vinyl railing will provide superior strength plus it is virtually maintenance
More informationDowntown Rack. Custom logo option available
Custom logo option available Downtown Rack The Downtown Rack uses thick, square-tube construction that can t be cut with a pipe cutter. The extended width of the Downtown Rack makes for easy bike parking
More informationThe Heritage Pergola
Eye Level Corporation One Trefoil Drive Trumbull, CT 06611 USA Phone: 888.782.1760 Fax: 888.782.1761 www.@eyelevelliving.com The Heritage Pergola Installation Instructions ARBORS COLUMNS HOSE REELS MAILBOX
More information6 1/2 x 6 1/2 Wood Grain Flat Top Pergola
6 / x 6 / Wood Grain Flat Top Pergola A S S E M B LY G U I D E Models: Lakewood OPTIONAL ACCESSORY Bolt Down Bracket Kit Ver /AUG/0 Ta b l e o f Co n t e n t s PAGE The 6.5 x 6.5 Wo o d Grain Flat Top
More information6 1/2 x 6 1/2 Wood Grain Flat Top Pergola
/ x / Wood Grain Flat Top Pergola A S S E M B LY G U I D E Models: Lakewood OPTIONAL ACCESSORY Bolt Down Bracket Kit V.-09 Ta b l e o f Co n t e n t s The PAGE Introduction & Overview.......................................................
More informationSwerve Rack CUSTOM RACKS AVAILABLE
CUSTOM RACKS AVAILABLE Swerve Rack The design of the Swerve mirrors the bike frame, thus providing superior bike support while making it easy to secure both the bike frame and wheel with a standard u-lock.
More informationTREX TRANSCEND RAILING
RAILING NOTES:» RAILINGS ARE DESIGNED TO BE INSTALLED OVER THE DECKING FRAME OR ON INSIDE OF RIM JOIST. NOTCHING OF PRESSURE-TREATED POSTS OR POSTS INSTALLED ON OUTSIDE OF RIM JOIST IS NOT ALLOWED.» All
More information10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.-007 Table of Contents PAGE 0x0 Trellis Pergola Introduction & Overview...................................................... Pergola Materials Overview..............................................................
More informationAssembly Instructions
10' and 12' Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/20/09 Cedar Gazebo Assembly Instructions
More information> Installation Instructions
SmarterFence BY BEDFORD TECHNOLOGY > Installation Instructions BEFORE YOU START > Check to see if a permit is needed in your area. > Check with your local utility companies to locate any underground utilities.
More informationInstallation Manual for
Installation Manual for Biscayne, Sanibel, St. Augustine All Single and Dual Decorative Steel Driveway Models 3121 Hartsfield Road Tallahassee, Florida, USA 32303 Telephone GTO Sales: 1-800-543-GATE (4283)
More informationINSTALLATION MANUAL VERANDA ENCLAVE RAILING. Model # SEC17 EW R15 PRE W/H SEC17 EW R15 KD W/HW SEC17 EWS R13 KD W/H
Model # SEC17 EW R15 PRE W/H SEC17 EW R15 KD W/HW SEC17 EWS R13 KD W/H INSTALLATION MANUAL VERANDA ENCLAVE RAILING Questions, problems, missing parts? Before returning to the store, call Veranda Customer
More informationInstallation Instructions Free-Standing Pergola
Outdoor Distinctions 303 W. Carmel Drive Carmel, IN 46032 844.345.2424 www.outdoordistinctions.com Free-Standing Pergola Harmony Series (14 x 10, 14 x 12, 14 x 14, 14 x 16, 14 x 18, 14 x 20) 1 (14 x 10,
More information6 1/2 x 6 1/2 Wood Grain Flat Top Pergola
/ x / Wood Grain Flat Top Pergola A S S E M B LY G U I D E Models: Lakewood OPTIONAL ACCESSORY Bolt Down Bracket Kit V.- Ta b l e o f Co n t e n t s The PAGE Introduction & Overview.......................................................
More information12 x 12 Flat Top Pergola
x Flat Top Pergola Model: Regency, Roosevelt A S S E M B L Y G U I D E O P T I O N A L A C C E S S O R Y Bolt Down Bracket Kit ( for Pergola) Ver./MAR 0 Ta b l e o f Co n t e n t s PAGE x Flat Top Pergola
More information12 x 12 Flat Top Pergola
x Flat Top Pergola A S S E M B LY G U I D E Model: Freemont OPTIONAL ACCESSORY Bolt Down Bracket Kit ( for Pergola) Ver /NOV 00 AI-BP0-0- Ta b l e o f Co n t e n t s PAGE x Flat Top Pergola Introduction
More informationClassic Vinyl Stair Railing. Installation Guide
Classic Vinyl Stair Railing Installation Guide THE BEST CHOICE FOR STRONG & DURABLE RAILING SYSTEMS Our exclusive manufacturing process ensures our vinyl railing will provide superior strength plus it
More informationPARTS INCLUDED IN FIXED STAIR CABLE RAIL KIT:
175 SERIES FIXED STAIR CABLE RAIL - INSTALLATION INSTRUCTIONS PARTS INCLUDED IN FIXED STAIR CABLE RAIL KIT: FIXED STAIR TOP RAIL (1) A FIXED STAIR BOTTOM RAIL (1) B D UPPER SADDLE BRACKET (1) C BRACKET
More informationWindsor Arbor. Parts List: General Information: Tools required: Assembly & installation Instructions
Windsor Arbor Assembly & installation Instructions Parts List: General Information:» Read through carefully before beginning assembly.» When assembling components, place on a clean, flat, non-abrasive
More informationInstallation Guide. for E-Series/Eagle Clad Hinged Inswing French Door
Installation Guide for E-Series/Eagle Clad Hinged Inswing French Door Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place.
More information12 x 12 Flat Top Pergola
x Flat Top Pergola Model: Freemont A S S E M B L Y G U I D E O P T I O N A L A C C E S S O R Y Bolt Down Bracket Kit ( for Pergola) Ver.-057 Ta b l e o f Co n t e n t s PAGE x Flat Top Pergola Introduction
More information