Pour un décor qui sort véritablement de l ordinaire! For a decor that really stands out!

Size: px

Start display at page:

Download "Pour un décor qui sort véritablement de l ordinaire! For a decor that really stands out!"

Robyn Mason
5 years ago
Views:

1 Pour un décor qui sort véritablement de l ordinaire! For a decor that really stands out! Technique d installation Installation Technique 1 Installation horizontale Tracez une ligne de niveau en calculant un dégagement de ¾ au bas du mur + la largeur de la planche. Horizontal installation Draw a level line leaving a ¾ in. space between the line and the bottom of the wall + the width of the boards. Scannez ce code pour accéder à la vidéo d installation. Scan this code to access the installation video.

2 - Pour le premier et dernier rang, utilisez seulement les planches de même épaisseur.

- Appliquez de la colle à construction sur le premier rang et répétez l étape de collage seulement tous les 4 rangs ainsi que sur le dernier.

- Pour jointer bout à bout les planches, seulement les apposer les unes contre les autres et répétez l opération de fixation.

- Apply construction glue to the first row and repeat this step only to every fourth row and to the last row.

- To butt joint the boards, place them one against the other and repeat the anchoring process.

2 2 - Pour le premier et dernier rang, utilisez seulement les planches de même épaisseur. - Alignez le haut des planches avec la ligne de niveau, partie femelle vers le haut. - Appliquez de la colle à construction sur le premier rang et répétez l étape de collage seulement tous les 4 rangs ainsi que sur le dernier. - Avec une cloueuse à finition ou des attaches métalliques, fixez les planches au mur. - Pour jointer bout à bout les planches, seulement les apposer les unes contre les autres et répétez l opération de fixation. - For the first and last rows, only use boards of the same thickness. - Align the top of the boards with the level line with the female part facing up. - Apply construction glue to the first row and repeat this step only to every fourth row and to the last row. - Using a brad nailer or metal fasteners, install the boards on the wall. - To butt joint the boards, place them one against the other and repeat the anchoring process. 3 - À partir du second rang, vous pouvez utiliser les planches minces (7.6 mm) et les planches épaisses (11.6 mm) en alternant ou au gré de votre fantaisie. - Répétez l opération pour tous les rangs. - Pour le dernier rang au haut du mur, nous suggérons de terminer avec des planches minces (7.6 mm). Ce qui permet l installation d une moulure de fi nition à votre guise. - From the second row on, use alternating thin (7.6 mm) or thick (11.6 mm) boards or whatever your heart desires. - Repeat for all rows. - For the last row at the top of the wall, we suggest ending with thin (7.6 mm) boards, which will allow the installation of a fi nishing moulding to your liking.

The best way to see the other side of the decor! Quick and easy to install!

Reverso allows you to transform your decor within a few hours and reveal the living or

Available in boxes of 10 reversible panels in two different colours so you can create a

Sandalwood Contour White Product specifications 10 per box of 3/8 inch x 12 inches x 24

melamine finish - Reversible Endless design possibility!

The plan will serve as a reference during the installation of your panels.

This will allow to properly start the installation process, even if your wall is not

Apply construction adhesive to the back of your first panel and align it with the level

3 The best way to see the other side of the decor! Quick and easy to install! No need to devote your entire week-end! Reverso allows you to transform your decor within a few hours and reveal the living or working environment of your dreams! Available in boxes of 10 reversible panels in two different colours so you can create a multitude of designs! Sandalwood Contour White Product specifications 10 per box of 3/8 inch x 12 inches x 24 inches Box coverage of 20 ft 2 Installation Technique Easy to install - Reversible 2 sides melamine finish - Reversible Endless design possibility! Suggested Designs 1 Choose your pattern and draw a plan on a sheet of paper. The plan will serve as a reference during the installation of your panels. 2 3 First of all, draw a level line. This will allow to properly start the installation process, even if your wall is not perfectly straight. Don t rely on the wall, the level line is your starting point. Apply construction adhesive to the back of your first panel and align it with the level line. You will then have to glue most of the other panels, depending on the pattern you have chosen. Scan this code to access the installation video on walldesign.ca 4 To secure the panel once it has been glued, insert the strips in the grooves. 5 Nail into the strips at a 45 degree angle. This will allow to camouflage the nail heads and provide a smoother finish. Support Canadian Products. Save Canadian Jobs. walldesign.ca

4 Installation guide For a decor that really stands out!

5 Characteristics of the Product The manufacturing process of the D3D panels includes different steps. In the end, the panels could be slightly curved. Not to worry! This is absolutely normal. The curve will completely and readily disappear if you follow the suggested installation instructions. A : MDF ¾ MDF with a white melamine backing the standard model. Panel Sizes and Angles of the Design The D3D panels are available in the following standard format: 48 x 96. All models are also available in a sixty-inch-wide version; please note that this version is only offered with the standard MDF option and at a slight additional cost. Each model includes a recurrent design on all four sides. They can therefore be installed side by side and you simply have to superimpose them to extend the motif. The angle of the designs on the standard versions is vertical, but nonstandard panels with horizontal motifs are also available at an additional cost. Recurrent designs are only available with the 48 x 96 panels. Installation Two installation methods are suggested for the D3D panels : Applying a PL Premium type construction adhesive on the back of the panels and installing them on a solid surface. It is recommended to use finishing nails to secure the panels until the adhesive has completely dried. Using Z-Clips is highly recommended when the thickness of the panels is such that the clips can be screwed into them. The panels can be cut with a table saw, a circular saw or a jigsaw. To cut out the areas for your electrical outlets, simply measure the location of the outlets and drill four holes at each extremity. The rectangle can then be easily cut out with a jigsaw. Installation guide 2

The Finishing Touch All D3D panels are sold unfinished (MDF). It is highly recommended to sand the panels before painting them. On some models, the use of a paint gun gives better results.

6 The Finishing Touch All D3D panels are sold unfinished (MDF). It is highly recommended to sand the panels before painting them. On some models, the use of a paint gun gives better results. A thermoplastic finish can also be applied to the D3D panels, which allows you to match them with existing melamine colours. A new range of innovative and avant-garde products that, combined with your vision, will allow you to create the decor of your dreams. Enter into the D3D dimension! WALL D3d PANEL Z-Clip murdesign.ca / walldesign.ca Installation guide 3

7 Installing your WallDesign Panels The following are illustrations of all the tools and accessories needed to successfully install your WallDesign panels. Installation technique 1 A few simple precautions will guarantee a problem-free installation of your long-lasting panel. Take into account the humidity level of the room in which you will be installing the panels. In the case of wood-based products, the humidity level has an impact on the wood s expansion and contraction. The room s relative humidity must not be less than 30% or higher than 50%. Above all, store your WallDesign panels for a period of 48 to 72 hours in the room where you plan to install them: it is essential that they acclimatize to the room temperature and humidity. Lay the panels fl at on their m (8-ft) lengths against the wall to allow for adequate ambient air fl ow between the panels.

2 Even the simplest installations require some

They also need to be clean, dry and fi rm.

The panels can be directly installed on studs, but we

which will enhance the joints quality and provide

For below-grade installations or exterior walls, use a

3 A strong start will guarantee successful results.

At the base of the wall, draw a reference line using your

This will enable you to make sure that your panels are

476-cm (3/16-in) gap against corners, windows and doors,

4 5 The panels must be securely fastened.

you apply it all around to the back-side perimeter and

8 2 Even the simplest installations require some preparation. Your walls must be as level as possible. They also need to be clean, dry and fi rm. This preparation is crucial to obtaining optimal results. The panels can be directly installed on studs, but we strongly recommend adding furring strips horizontally, which will enhance the joints quality and provide increased solidity. For below-grade installations or exterior walls, use a 4-mil vapour barrier underneath each panel. 3 A strong start will guarantee successful results. Always work with a level. At the base of the wall, draw a reference line using your level. This will enable you to make sure that your panels are straight, even if your walls are not square. Leave a cm (3/16-in) gap against corners, windows and doors, and at the top and bottom of each panel. 4 5 The panels must be securely fastened. Before securing the panels, dry-fit them first to make sure they fit properly. Use a construction or panel adhesive on the back of each panel. A cm (¼-in) adhesive bead will be enough, as long as you apply it all around to the back-side perimeter and forming a repetitive S pattern to the rest of the back side for a drywall application. For a direct-to-stud/furring strip application, apply the same cm (¼-in) adhesive bead to each stud or furring strip. Finish securing each panel using a brad nailer. Make sure to do the nailing in the grooves so that the nails are less visible; this will provide a smoother fi nish.

6 In construction, joints are always somewhat touchy areas. Reinforce each joint with this helpful hint.

Cutting 7 All WallDesign panels are made from HDF, the same 8 component that goes into laminate fl ooring. To cut a panel, use a laminate fl ooring blade on a table saw with the fi nish side up.

jigsaw with a fi ne toothed blade to cut the outlet. Maintenance Wash the wall panels using a clean cloth and mild soap. Avoid using a stronger soap, as it may alter the paint fi nish.

If you want to re-paint your panels, you will fi rst need to scuff the surface lightly to make sure the new paint adheres well to the panels. For a ceiling application, leave a 0.

9 6 In construction, joints are always somewhat touchy areas. Reinforce each joint with this helpful hint. Apply a wood glue-type adhesive to the joint to prevent the panels from separating after their installation. Afterwards, simply remove the excess glue according to the manufacturer s instructions. Cutting 7 All WallDesign panels are made from HDF, the same 8 component that goes into laminate fl ooring. To cut a panel, use a laminate fl ooring blade on a table saw with the fi nish side up. If you want to use another type of power saw such as a portable circular saw or an outlet, measure and mark down the perimeter to be cut; drill a hole into each corner of the perimeter, and use a jigsaw with a fi ne toothed blade to cut the outlet. Maintenance Wash the wall panels using a clean cloth and mild soap. Avoid using a stronger soap, as it may alter the paint fi nish. Miscellaneous You can complete your decor with trim and chair rails. Miter cutting can be done on a tail cutter for a clean fi nish on the outside or inside corners. If you want to re-paint your panels, you will fi rst need to scuff the surface lightly to make sure the new paint adheres well to the panels. For a ceiling application, leave a cm (¼-in) gap all around the perimeter. Use a strong, high-quality construction adhesive and drive more nails than in a wall application. You re off to a good start. Continue installing your panels. Different fi nishing options are available. The panels can be installed on a full wall or you can leave a space for mouldings. The inner and outer corners can be simply glued one over the other or you can choose to install them at a 45 degree angle, which provides a more refi ned cachet to your fi nal results. For panels at the base of your walls, you can easily coordinate them with your wall panels and install a chair rail to create a dramatic effect to your decor. Now, sit back and admire your work... and, especially, enjoy! WallDesign is a plus, not only for your walls, but for your quality of life! walldesign.ca

Installation Instructions Palladium Wall Panels - Demountable Factory Finished Edges and Field Cut Edges

Installation Instructions Palladium Wall Panels - Demountable Factory Finished Edges and Field Cut Edges Please read all instructions before installing Palladium Wall Panel System. 1. Before installation: a. Acclimate Palladium Panels, reveals, adhesives and wall substrates to room temperature 24 hours before