FOR YOUR SAFETY: READ ALL INSTRUCTIONS CAREFULLY

Size: px

Start display at page:

Download "FOR YOUR SAFETY: READ ALL INSTRUCTIONS CAREFULLY"

Cory Lang
5 years ago
Views:

1 MODEL 2020F FOR YOUR SAFETY: READ ALL INSTRUCTIONS CAREFULLY

2 Table of Contents General safety instructions for Power Tools 1 Main specification 2 Unpacking and checking contents 2 List of loose parts in the box and bags. 3 Getting to know your drill press..4 Assembly.. 5 Lubrication 6 Maintenance 6 Wire diagram 6 Trouble shooting. 9 Repair parts.. 10 General safety instructions for Power Tools 1.KNOW YOUR POWER TOOL Read and understand the ower's manual and labels affixed to the tool.learn its application and limitations as well as the specific potential hazards peculiar to this tool. 2.GROUND ALL TOOLS This tool is equipped with an approved 3 conductor and a 3 prong grounding type plug to fit the proper grounding type receptacle. 3.KEEP GUARDS IN PLACE In working order and in proper adjustment and alignment. 4.WEAR PROPER APPAREL Do not wear loose clothing,gloves,neckties,or jewelry (rings,wrist,watches) to get caught in moving parts.wear protective hair covering to contain long hair.roll long sleeves above the elbow. 5.USE SAFETY GOGGLES 6.KEEP WORK AREA CLEAN Cluttered areas and benches invite accidents.floor must not be slippery due to wax or sawdust. 7.KEEP CHILDREN AWAY -1-

3 Main Specification Drill Capacity Chuck Capacity Sewing Spindle Taper Distance,Spindle to column Max.Spindle travel Column Diameter Motor Base Size Table Size Overall Height 32mm / 1-17/64 in. 20mm / 25/32 in. 510mm / 20 in. MT3 255mm / 10-3/64 in 120mm / 4-23/32 in. 92mm / 3-5/8 in. 120V, Single Phase,1500W mm / 22-53/ /32 in mm / 18-45/ /32 in 1710mm / 67-21/64 in. Range of spindle speeds 12 speeds Motor Speed Spindle Speeds (min -1 ) 60Hz 1700 min Dimensions Totals(L M H) mm / 57-3/ / /64 in. Net weight 120KGS / 265 lbs. Unpacking and checking contents 1.Unpacking and checking contents Separate all the parts from packaging materials and check each item make sure all items are acco for before discarding any packing material. Item Description Qty A Table (square or Round ). 1 B Column Support Asm. 1 C Owner's Manual 1 D Box of Loose Parts.. 1 E Bag of Loose Parts.. * F Base. 1 G Head Asm Remove the protective oil that is applied to the table and column.use any ordinary household type grease and spot remover 3.Apply a coat of paste wax to the table and column to prevent rust.wipe all parts thoroughly with

4 clean dry cloth. -2-

5 n. n.. ounted h

7 List of Loose Parts in the box and bags -3-

8 Getting to know your drill press - 4-

9 Assembly Refer to the figure install all parts correctly, tighten the screw and bolts securelly. 1 Collar-Rack 2. Screw-Hex Soc Set M6* Support Table w/indicator 4 Crank 5 Handle-Crank 6 Rack 7 Screw-Hex Soc Set M10* support Column 9 Screw-Hex Hd M12* Base 11 Tube-Column 12 Table Lock 13 Worm-Elevation 14 Table w/scale 15 Key Chuck 16 Head Asm

10 Lubrication All of the BALL BEARING are packed with grease at the factory.they require no further lubrication. Periodically lubricate the table elevation machanism,the SPLINES (grooves) in the spindle,and the RACK (teeth of the quill),see "Getting to know your drill press." Maintenance Frequently blow out any dust that may accumulate inside the motor. A coat of automotive type paste was applied to the table and column will help to keep the surfaces clean. Wire diagram - 6-

11 - 7-

12 Trouble Shooting TROUBLE PROBABALE CAUSE REMEDY Noisy Operation Drill bit burns Drill bit leads off hole not round Wood splinters on underside Workpiece turn loose from hand Drill bit binds in workpiece Excessive drill bit runout or wobble 1.Incorrect belt tension. 2.Dry Spindle. 3.Loose spindle pulley 4.Loose motor pulley 1.Incorrect speed. 1.Adjust tension. 2.Lubricate spindle. 3.Checking tightness of retaining nut on pulley,and tighten if necessary. 4.Tighten setscrews in pulleys. 1.Change speed. 2.Chips not coming out of hole. 2.Retract drill bit frequently to clear chips. 3.Dull drill bit 4.Feeding too slow 5.Not lubricated 1.Hard grain in wood or lengths of cutting lips and/or angles not equal 2.Bent drill bit 1.No "back up material" under workpiece. 1.Not supported or clamped properly. 1.Workpiece pinching drill bit or excessive feed pressure. 2.Improper belt tension. 1.Bent drill bit 2.Worn spindle bearings. 3.Drill but not properly installed in chuck 4.chuck not properly installed. 3.Resharpen drill bit. 4.Faster the speed. 5.Lubricate drill bit. 1.Resharpen drill bit correctly. 2.Replace drill bit. 1.Use "back-up material" 1.Support working or clamp it. 1.Support working or clamp it. 2.Adjust temsion. 1.Use a straight drill bit. 2.Replace bearings. 3.Install drill bit properly. 4.Install chuck properly. Quill Returns too slow or too fast 1.Spring has improper tension. 1.Adjust spring tension. Chuck will not stay atached to spindle if falls off when trying to install it. 1.Dirty,grease,or oil on the 1.Using a household detergent clean the tapered inside surface of chuck tapered surface of the chuck and spindle to or on the spindles tapered remove all dirt,grease and oil. surface. -8-

13 Repair Parts Key No. Description FIGURE1 PARTS LIST Key No. 1 Collar-Rack 10 Base 2 Screw-Hex Soc Set 11 Tube Column M6* Pin-Table Lock Description 3 Support-Table w/indicator 13 Nut-Hex Hd M8* Crank 14 Screw-Hex Hd M20* Handle-Crank 15 Table w/scale 6 Rack 16 Pin-Gear 7 Screw-Hex Soc Set 17 Clamp-Column M10* Gear-Helical 8 Support-Column 19 Worm-Elevation 9 Screw-Hex HdM12*

14 Repair Parts FIGURE2 PARTS LIST Key No. Description 1 Nut-Lock M20*1.5 2 Ring-Locking 3 Washer 4 Bearing-Ball 20mm 5 Washer-Rubber 6 Tube-Quill 7 Key-drill 8 Key-Chuck 9 Chuck 10 Arbor 11 Spindle 12 Bearing-Ball 30mm 13 Bearing-Thrust -10-

15 Repair Parts FIGURE3 PARTS LIST Key No. Description Key No. Description 1 Belt-"V"A29 11 Lock Washer Ext M6 2 Bearing-Ball 15mm 12 Washer Foam 3 Pully-Center 13 Guard-Pulley w/labels 4 Pivot-Ldler 14 Ring-Retaining 5 Pulley-Motor 15 Bearing-Ball 30mm 6 Screw-Soc Set M8* Spacer-Bearing 7 Screw-Pan HD M5* Insert-Pulley 8 Clamp-Cord 18 Pulley-Spindle 9 Bushing-Rubber 19 Nut-Pulley 10 Screw-RD Washer Hd 20 Belt-"V"A33 M6* Knob -11-

16 -12-

17 FIGURE4 PARTS LIST Key No. Description Key No. Description 1 Screw-Hex HD M8* Box Switch 2 Lever-Adjusting 27 Screw-Pan Cr M6* Support-Motor Bracket 28 Switch 4 Mount-Motor 29 Screw-Self Tap Pan Hd 5 Lockwasher 12mm M4.2* Nut-Hex M8* Key-Switch 7 Motor 31 Cover-Switch Plate 8 Nut-Hex M8* Switch-Locker 9 Washer 8 33 Screw-Pan Cr M6* Cord-Motor 34 Lead-3" 11 Screw-Hex HD M8* Screw-Soc Hd Cap 12 Support-Motor Bracket M8* knob-motor Adjusting 36 Screw Special Set 14 Handle-Belt Tension M10* Screw-Soc Set M10* Nut-Hex M10* Lock-Depth Screw 38 Seat-Spring 17 Guide Scale 39 Pin-Roll 6*16 18 Knob 40 Spring-Torsion 19 Rod 41 Cap-Spring 20 Hub 42 Nut-Hex M12* Ring-Depth Stop W/Scale 43 Cord-Power 22 Pin-Stop 44 Pin-Roll 2.5*10 23 Screw-Soc Hd Cap 45 Head w/pointer and Trim M8* Connector-Wire 24 Lock-Washer-Ext M5 47 Screw-Pan Cr M6* Screw-Pan Cr M5* Socket-Bulb -13-

Instruction Manual DP58P. Pedestal Drilling Machine

Instruction Manual DP58P. Pedestal Drilling Machine DP58P Pedestal Drilling Machine Instruction Manual IMPORTANT For your safety read instructions carefully before assembling this product. Save this manual for future reference. Woodworking Machines & Accessories