Single-point fixing serie S32/35

Transcription

1 MNET Single-point fixing Single-point fixing serie S2/ The basic component within the MNET system is the single-point fixing a basic rather than cylindrical bore in the glass, has a tapered countersunk bore for a perfect seated fit to the glass. These give a flush finish of the singlepoint fixing in all applications. The three-dimensional adjustability incorporated within the fitting ensures ideal compensation for structural and drilling tolerances. onstraint-free transmission of all the forces acting on the glass to the substructure is also ensured. omponents 1 lip-on cover 2 Pin internal thread onical sleeve 4 Gasket Fixing djustment screw Threaded rod M8 with small head (eg DIN 912). Length and type to suit wallplug. Wallplug on site to suit wall construction. Installation and adjustment 1 2 -dimensional adjustment perture for post-installation adjustment of screw Post-installation adjustment of ± 2 mm horizontally and vertically by rotating the oblong hole. 4 djustment screw allows offset from wall to be altered depending on type of fitting. Transfer the drilling points from the installation drawing to the wall. Drill anchor holes for wall plugs. Undo adjustment fastener and secure to the wall. Only lightly tighten fastener so that it can still be moved. Mount the fixing and washer and fit the glass. Undo the adjustment fastener and then secure in final position. lign single-point fixings and secure with grub screw. Fit tapered nut and clamping ring and tighten with special wrench (tightening torque 1 Nm). lip on covers. 4 07/04

2 Type and ordering information Ø Ø Ø Ø not offset mm offset mm offset mm offset mm not Order No Order No Order No Order No Order No Order No Order No Order No mm: Order No mm: Order No mm: Order No mm: Order No mm: Order No mm: Order No mm: Order No mm: Order No mm: Order No mm: Order No mm: Order No mm: Order No /04

3 MNET The system approach is very much in evidence in the case of the interconnecting components. Elements such as clamping and angle connectors of various designs and also interconnecting fasteners of various lengths can be combined in order to attach glass of different thicknesses at any required angle to the floor, to ceilings, to walls and to plinth supports. Single-point fixings flush with the glass are also used for this interconnection and glass-to-glass system. Tolerances are compensated by sloted holes in the interconnecting fasteners Ordering information 1 Pivoting glass clamp 8-12 mm Order No Glass thickn mm Order No Glass thickn mm Order No Pivoting wall fixing Order No olumn eiling/floor fixing Order No lamping connector Order No mm 82 mm Length 2. mm Order No mm 10 mm Length 0 mm Order No Length 82 mm Order No Length 10 mm Order No /04

4 -180 Glass/Glass onnector for double panel -180 Ordering information Glass/Glass 8-12 mm 2. mm Order No Glass / Glass ø ø2 ø20 0 mm Order No mm Order No / 0 / 82 / 10 mm 10 mm Order No Glass / Wall ø20 ø 8-12 mm glass thickness 2. / 0 / 82 mm 2. Wall 2. mm Order No mm Order No omponents and assembly of the glass fixing 1 2 Glass Glass 7 8 ø 2 see page 82 mm Order No onnector for Material 1.40 Order No Material Order No omponents and assembly of the wall fixing 8 see page via oblong hole 9 grub screw 10 Threaded rod M8 with small head (eg DIN 912). Length and type to suit wallplug dimensional adjustment via oblong hole Wallplug on site to suit wall construction. omponents 1 lip-on cover 2 onnecting bolt onical collar 4 onical sleeve Gasket Pivoting clamp 7 onnecting bolt 8 to suit length 9 onnecting bolt 10 Pivoting clamp 11 Fixing plate 07/04 7

5 MNET Ordering information with clamping disc lamping connector Order No Single-point countersunk orner connector Glass/ceiling, Glass/floor connection omponents/ Installation or steel cable 1 2 ø20 ø (only supporting function) Order No eiling fixing (bearing function) Order No with clamping disc Order No via oblong hole 4 Hanging glass from the ceiling is permissible where there is other support for the glass sheet. 2-dimensional adjustment Threaded rod M8 with small head (eg DIN 912). Length and type to suit wallplug. Grub screw 4 Wallplug on site to suit wall construction. 7 omponents 1 onnecting bolt 2 Pivoting clamp onnecting bolt 4 Gasket Pivoting clamp Fixing plate 7 olumn lip-on cover Height adjustment via grub screw Single-point fixing countersunk Single-point fixing clamping disc Fixing with cheesehead screw DIN 7984 M10 x..., or oval-head wood screw DIN x... depending on ceiling fixing requirements and wallplug type (by others) 8 07/04

6 Glass preparation for single-point fixings and corner connections For ESG and VSG out of ESG. Recommended centres for fixed glazing element max. 800 ±0. max. 800 ±0. ±0. ountersunk holes for countersunk single-point fixings ø ø2 ylindrical bore for clamping disc single-point fixings ø Dimension Dimension Dimension ngle Wall Dimension Dimension 2. Plan view orner connectors Glass/Glass ngle Dimension orner connectors Dimensions in mm orner connectors Glass/Glass ngle / ngle Length of Dimensions for 10 mm glass thickness (consider other glass thicknesses). / / / 0 Length of Dimensions for 10 mm glass thickness (consider other glass thicknesses). / / / 7/ 72/70 87./8 lamping connector 10 Ensure compliance with minimum glass/bore clearances as per glass manufacturer recommendations ylindrical bore Ø1 0 orner connector glass/ceiling orner connector glass/floor eiling fixing (bearing) eiling 41, Decke KS Floor Vertically adjustment ± 2. Glass preparation with a tolerance of max. ± 0. mm is recommended. 07/04 9