Specification Tapped holes f. coupl Scope Allocation of the JED Numbers General...
|
|
- Kelley Parsons
- 5 years ago
- Views:
Transcription
1 WABCO Specification Class: Engineering Guidelines Class No.:62 Tapped Holes for Couplings JED according to ISO Previous Edition Abbreviated Title Tapped holes f. coupl Scope Allocation of the JED Numbers General Tapped Holes and Male Fittings Tapped hole dimensions according to JED Male Fittings and Dimensions according to ISO Representation on Drawings Representation on the Outline Drawing, Document Code 605/ Representation on the Sectional Drawing, Document Code 606/652 and Component Drawing, Document Code 607/ Minimum Center Spacing of Tapped Holes Tightening Torques Maximum Permissible Tightening Torque for the Tapped Holes Maximum Permissible Tightening Torques for the Coupling... 7 Continuation page 2 to 7 Group Standards Responsible for the Contents TRI: 002 Approved by Doc. Code Rev. 408 A
2 JED-464 : Page 2 1 Scope This specification defines the dimensions of tapped holes and shows the representation of dimensioning in the Component, Blank and Outline Drawings. Tapped holes, as defined in this specification, with a conical sealing surface, of the metric series, used in pneumatic braking systems on road vehicles using compressed air at a pressure below 2 MPa (20 bar) are designed for couplings according to the system of the PARKER, RAUFOSS and ANOFLEX Companies. This specification corresponds to ISO :1998 The previous issue of this specification ( ) contained dimensions as defined by Renault. The difference between the two versions consists in the increased length of the 10 countersinking, e.g. 2,4 mm instead of 2,0 mm for dimension M22 x 1, Allocation of the JED Numbers In old documents (approx to 2002), the standard JED-464 is indicated. In these cases, manufacture may also be made in accordance with the JED which is newly defined in the present document. In all documents to be newly created or revised, JED has to be indicated in order to clearly show the relation with the current version of the company standard. 2 General The dimensions apply to machining. The tapped holes made in accordance with the present specification are also suited for pipe couplings with flat gaskets or WABCO thrust ring and O-ring, provided that the male fitting has the profile defined in ISO : issue 1998, ISO : issue or DIN Form A: issue
3 JED-464 : Page 3 3 Tapped Holes and Male Fittings 3.1 Tapped hole dimensions according to JED D 2 ISO 965-6H D 3 + 0,4 0,1 D 4 D 5 1) 2) min. D 6 Min. l 1 min. l l 2 1) max. l 3 +0,4 M10 x 1 10, , ,5 1 1,6 M12 x 1, ,5 11,5 14 M14 x 1, ,5 11,5 14 1,5 2,4 M16 x 1, , ,5 M22 x 1, ,5 15, ) Maximum recommended depth of the centering face to allow sufficient engagement of the wrench to ensure appropriate tightness of fittings and lock-nuts. D 2 - medium as defined in ISO 965-1, i.e., tolerance quality 6H. If a deviating tolerance is required for machining, the indication has to be e.g. M22 x 1,5-6e / JED D 7 has to be selected in accordance with the desired nominal width. In the lower third (no O-ring contact!) of the O-ring sealing surface, tooling marks are acceptable.
4 JED-464 : Page Male Fittings and Dimensions according to ISO D 2 ISO g min. max. D 6 D 1 l 4 l 5 l 6 0 0,1 min. + 0, ,4 O-ring 1) (Inner diameter x cross-sectional diameter) M10 x 1 13,2 19,6 8,55 1,5 1,5 8 8 x 1,25 M12 x 1, ,9 9,85 9,4 x 2,1 M14 x 1, ,9 11,85 2 2, ,4 x 2,1 M16 x 1, ,3 13,85 13,4 x 1,9 M22 x1, ,1 19,85 2,5 19 x 2 1) Unless otherwise specified, O-rings shall have a minimum hardness of 70 IRHD, e. g. JED-7080M0
5 JED-464 : Page 5 4 Representation on Drawings The representations of holes in the documents have to show the finished condition which is stored as UDF (User Defined Feature) in the Pro/E (3D-CAD) repetition part database. The arrangement of the designation of thread on the projection line may be chosen, but the allocation has to be clear. 4.1 Representation on the Outline Drawing, Document Code 605/653 On customers request, tapped holes shall be indicated in the Outline Drawing only with their nominal diameter and reference to JED-464-0, e. g. M22x1,5 / JED The arrangement of these indications in a table including additional data may be useful.
6 JED-464 : Page Representation on the Sectional Drawing, Document Code 606/652 and Component Drawing, Document Code 607/651 On request of the Orderfulfilment Process, tapped holes shall be represented in the Sectional Drawing and Component Drawing only with the indication of the contour, nominal diameter and reference to JED-464-0, e. g. M22 x 1,5 / JED-464-0
7 JED-464 : Page 7 5 Minimum Center Spacing of Tapped Holes The indications of minimum center spacing L refer to straight male stud couplings and double-end flat flare nut wrenches according to DIN D 1 Hole Spacing L Usual widths Recommended sizes Minimum sizes across flats M10 x M12 x 1, M14 x 1, M16 x 1, M22 x 1, Tightening Torques 6.1 Maximum Permissible Tightening Torque for the Tapped Holes On the Outline Drawings, the maximum permissible tightening torque of the tapped holes (without fittings) applies as defined in JED-366. Deviating values (which might, for instance, be due to lower material strength of the body, e.g. plastic material) have to be indicated. 6.2 Maximum Permissible Tightening Torques for the Coupling On the Outline Drawings and Sectional Drawings, the tightening torque and the tolerance have to be indicated at all tapped holes shown with the fitting. The indications, maintenance and assembly instructions of the individual fitting manufacturers have to be observed.
Specification
Previous Edition Specification 2018-06 Class: Executing guidelines Class No.:62 Tapped holes for push-in connections JED system Voss Company 388 Abbreviated Title 2016-04 Tapped h.push-in con. Voss 852
More informationISO INTERNATIONAL STANDARD. Road vehicles Pneumatic braking systems Part 1: Pipes, male fittings and tapped holes with facial sealing surface
INTERNATIONAL STANDARD ISO 4039-1 First edition 1998-08-15 Road vehicles Pneumatic braking systems Part 1: Pipes, male fittings and tapped holes with facial sealing surface Véhicules routiers Dispositifs
More informationSpecification D data models
Previous Edition Specification 2017-04 Class: Dimensions, tolerances Class No.:01 Documentation of components by means of 3D data models 516 Part name (for databases) 2009-09 3D data models 852 005 160
More informationSpecification
Specification 2001-09 Class: Executing guidelines Class No.:62 Date of Manufacture on WABCO Products JED 226 Prev. Edition Abbreviated Title 1994-11 Date of manuf.wabco prod. 852 002 260 4 1 Scope...2
More informationDETAIL SPECIFICATION SHEET FITTING, INSTALLATION, FLARED TUBE AND HOSE, SWIVEL
INCH-POUND MS33786B 12 February 2013 SUPERSEDING MS33786A 1 February 1985 DETAIL SPECIFICATION SHEET FITTING, INSTALLATION, FLARED TUBE AND HOSE, SWIVEL This specification is approved for use by all Departments
More informationJED Specification
JED Specification 2008-08 Class: Engineering guidelines Class No.:07 Marking of WABCO products JED 341 Previous Edition Abbreviated Title 1988-12 Marking of WABCO products 852 003 410 4 1 Scope...3 2 Types
More informationAssembly instructions
Assembly instructions Important notes on VOSS assembly instructions In order to ensure maximum performance and functional reliability of VOSS products, the respective assembly instructions, operating conditions
More informationOWNER: POSITION AUTHOR: POSITION Dan Boettcher Director of Engineering Richard Richardson Vice-Dir of Engineering
KRESS CORPORATION ENGINEERING Design of Thru and Threaded Holes Standard DOC ID 095007 REVISION A TYPE PORTAL OWNER: POSITION AUTHOR: POSITION Dan Boettcher Director of Engineering Richard Richardson Vice-Dir
More informationAssembly instructions
Assembly instructions Important notes on VOSS assembly instructions In order to ensure maximum performance and functional reliability of VOSS products, the respective assembly instructions, operating conditions
More informationClamping devices 521
Clamping devices 521 522 Product overview Clamping devices Adjustable straps K0001 Hook clamps K0012 Goose-neck straps with long slot K0002 Page 526 Hook Clamps with collar K0013 Page 535 Equipped clamps
More informationEnsat driving tools...
nsat driving tools... On this page, you can configure the optimum tool for your application. A configuration is provided in the following as an illustrative example. The article number is composed of two
More informationKerkau Manufacturing. B16.5 Flange Book
Kerkau Manufacturing B16.5 Flange Book TABLE OF CONTENTS Revision 1 Title Page Table of Contents Tolerance Page Permissible Imperfections Dimensions of Flange Facings (all pressure rating classes) Dimensions
More informationUNIT 9b: SCREW FASTENERS Introduction Functions Screw Features Elements Terms of a Thread Profile
UNIT 9b: SCREW FASTENERS Introduction A mechanical screw is a cylinder or cone that has a helical ridge called a thread. A helix has one or more turns, so a screw can have several turns. If the helix is
More informationDETAIL SPECIFICATION SHEET FITTINGS - INSTALLATION OF FLARED TUBE, STRAIGHT, THREADED CONNECTORS, DESIGN STANDARD FOR
INCH-POUND MS21344A 4 October 2016 SUPERSEDING MS21344 17 August 1971 DETAIL SPECIFICATION SHEET FITTINGS - INSTALLATION OF FLARED TUBE, STRAIGHT, THREADED CONNECTORS, DESIGN STANDARD FOR This specification
More informationThread and End Connection
www.swagelok.com and End Connection I d e n t i f i c a t i o n G u i d e Contents Introduction and End Connection Terminology.. 4 General Terminology................... 5 Step-by-Step Identification
More informationNELSON STUD WELDING ACCESSORY SPECIFICATION: Stud Weld Gun Imperial Dimension Chucks
Type 1 4 #2 Morse Taper Mounting NELSON STUD WELDING ACCESSORY SPECIFICATION: Stud Weld Gun s Below is a list of standard imperial chucks for use in welding Nelson studs. The chucks are listed with both
More informationEngineering Data Gas Spring Clamps
Engineering Data Gas Spring Clamps The New Industry Standard This product may be covered by one or more patents or patent applications. See http://www.standardlifters.com/patents.html for details. 12/13
More informationMAG-CONV Basic, 48, 48R & Midline Front Mount
Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total
More informationAssembly instructions
Assembly instructions Important notes on VOSS assembly instructions In order to ensure maximum performance and functional reliability of VOSS products, the respective assembly instructions, operating conditions
More informationFord Water Meter Couplings & Accessories
Section H 2/2001 Ford Water Meter Couplings & Accessories The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260/563-3171 FAX: 1-800-826-3487 Overseas
More informationI-W07/W77. Couplings DETAIL A WARNING. Photo Showing Pipe with Weld Seam Ground 6 inches/152 mm Back from Pipe End and an AGS Groove
WARNING Read and understand all instructions before attempting to install any Victaulic piping products. These products must be used only on pipe that is prepared to Victaulic Advanced Groove System (AGS)
More informationMATERIAL AND EQUIPMENT STANDARD FOR METRIC TYPE FASTENERS (SCREWS, BOLTS, STUDS, NUTS AND WASHERS) ORIGINAL EDITION DEC. 1997
MATERIAL AND EQUIPMENT STANDARD FOR METRIC TYPE FASTENERS (SCREWS, BOLTS, STUDS, NUTS AND WASHERS) ORIGINAL EDITION DEC. 1997 This Standard is the property of Iranian Ministry of Petroleum. All rights
More informationThe Ensat self-tapping threaded
The nsat self-tapping threaded insert nsat is a self-tapping threaded insert with external and internal threads,cutting slots or cutting bores. A continuous process of further development has brought about
More informationTECH SHEET PEM - REF / AXIAL THREAD CLEARANCE. SUBJECT: Method for providing adequate axial thread clearance
SUBJECT: Method for providing adequate axial thread clearance In our long history of working with customers in the application of our self-clinching nuts, PennEngineering has seen numerous instances of
More informationEngineering Data Rail Lifters
Engineering Data Rail Lifters Bolt On Ready Stock Rails This product may be covered by one or more patents or patent applications. See http://www.standardlifters.com/patents.html for details. 12/13 - Rev.
More informationMECHANICAL ASSEMBLY John Wiley & Sons, Inc. M. P. Groover, Fundamentals of Modern Manufacturing 2/e
MECHANICAL ASSEMBLY Threaded Fasteners Rivets and Eyelets Assembly Methods Based on Interference Fits Other Mechanical Fastening Methods Molding Inserts and Integral Fasteners Design for Assembly Mechanical
More informationFasteners. Bolts. NAPA FastTrack Counter Sales Training Fasteners Page 1. Figure 1. Typical Measurements for a Bolt or Hex Head Cap Screw
Fasteners Many types and sizes of fasteners are used in the automotive industry. Each fastener is designed for a specific purpose and condition. One of the most commonly used type of fastener is the threaded
More informationUNSIGNED HARDCOPY NOT CONTROLLED
Subject: APPROVED BY STATUS PURPOSE AFFECTED FUNCTIONS s Manager, Hardware Engineering Maintenance Revisioin Establishes requirements for the manufacture and inspection of pipe threads. L-3 Communications
More informationUnderstanding pipe threads: types and designations
WHITE PAPER 8008 Understanding pipe threads: types and designations By Mark Schmidt Applications Engineer CPC (Colder Products Company) Different types of screw threads have evolved for fastening and hydraulic
More informationGB/T Translated English of Chinese Standard: GB/T NATIONAL STANDARD OF THE
GB/T 9-00 Translated English of Chinese Standard: GB/T9-00 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS.00.0 J 0 GB/T 9-00 Replacing GB/T
More informationCH # 8. Two rectangular metal pieces, the aim is to join them
CH # 8 Screws, Fasteners, and the Design of Non-permanent Joints Department of Mechanical Engineering King Saud University Two rectangular metal pieces, the aim is to join them How this can be done? Function
More informationB-Too Drilling and Tapping Machine Instruction and Maintenance Manual
B-Too Drilling and Tapping Machine Instruction and Maintenance Manual Thank you for your purchase of the B-Too Drilling and Tapping Machine. Please read and understand this short operation manual. Our
More informationRamp Door OEM INSTALL MANUAL
Ramp Door OEM INSTALL MANUAL TABLE OF CONTENTS System and Safety Information 2 Weight Ratings 2 Ramp Door 2 Patio Door 2 Resources Required 2 Installation 3 Notes 5 System and Safety Information The following
More informationDirectional valves Electrically operated Series 563, 565, 567. Brochure
Directional valves Electrically operated Brochure 2 Directional valves Electrically operated 3/2-directional valve, Series 563 Qn = 1350 l/min plate connection Electr. connection: Plug, Form B, industry
More informationMETRIC FASTENERS 1520 METRIC FASTENERS
1520 METRIC FASTENERS METRIC FASTENERS A number of American National Standards covering metric bolts, screws, nuts, and washers have been established in cooperation with the Department of Defense in such
More informationThe Ensat self-tapping threaded insert...
The nsat self-tapping threaded insert... nsat is a self-tapping threaded insert with external and internal thread, cutting slots or cutting bores. A continuous process of further development has brought
More informationA q u a r i u s 3 5 M e d i u m a n d A q u a r i u s 3 5 W i d e
Pool 35 Focus and Pool 35 Wide User Manual A q u a r i u s 3 5 M e d i u m a n d A q u a r i u s 3 5 W i d e User Manual This manual describes the following products: Product numbers 033 0750 and 033 0755.
More informationPipe Restrainers series C Restrainers for use on IPEX Bionax AWWA CI OD C909 PVCO Pipe with MJ or Push-On Fittings
Pipe Restrainers series 1000 1000C Restrainers for use on IPEX Bionax AWWA CI OD C909 PVCO Pipe with MJ or Push-On Fittings INFORMATION Restrainers for restraining mechanical joint or push-on fittings
More information2-JAW SELF-CENTERING RADIAL PNEUMATIC GRIPPER (SERIES PS)
PS 2-JAW SELF-CENTERING RADIAL PNEUMATIC GRIPPER (SERIES PS) Double-acting radial motion. The gripping force is constant throughout the entire stroke (from 0 to 90, both opening and closing). Lightweight:
More informationTerraBrute CR (4-12 ) Pipe Installation Guide
1.0 Introduction TerraBrute CR is an integral-bell restrained-joint PVC pipe that meets the performance requirements of AWWA C900 (1). It has a slight modification that allows the joints to be locked for
More informationProcedure for Wrench Calibration and Snug Tightening
Procedure for Wrench Calibration and Snug Tightening 1. Scope: This procedure provides the method for calibration of a manual torque wrench or an adjustable impact wrench and the snug tightening procedure
More informationFord Raptor Venom Front Bumper Installation Instructions
PREPARATION 2010 2014 Ford Raptor Venom Front Bumper Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend
More informationInstallation Tools. Pipe Cutters for steel and cast iron pipes 598. Deburring Reamer / for stainless steel pipes 600. for copper pipes 602
596 597 Installation Tools Pipe Cutters for steel and cast iron pipes 598 Pipe Cutters / Pipe Deburring Reamer for stainless steel pipes 600 Pipe Cutters / Pipe Deburring Reamer / Calibrating Tool for
More information2-jaw parallel self-centering pneumatic gripper (series GM)
GM -jaw parallel self-centering pneumatic gripper (series GM) Double acting. The rugged construction lends itself to heavy duty applications for a trouble free long life without maintenance. Wide choice
More informationEnclosed Partition Installation Instructions
Nissan NV1500/2500/3500 High Roof Partition Kit Part #: DTC 1502-036 V1.0.08.06.18 IMPORTANT INSTALLATION STEPS ARE DENOTED USING A STOP SIGN. THESE STEPS MUST BE PERFORMED IN THE SPECIFIED ORDER TO ENSURE
More informationPneumatics x x x x x 80 std. 80 x x 160. Pneumatic Joining Plates. Pneumatic End Plates
Pneumatics M 1 x x x x x x Pneumatic Joining Plates x x x x x std. x x Pneumatic End Plates x x x x Pneumatic End Connectors x x x x Pneumatic Corner Connectors x x x x Pneumatic Joining Connectors x x
More informationISO INTERNATIONAL STANDARD. Fasteners Torque/clamp force testing. Éléments de fixation Essais couple/tension. First edition
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 16047 First edition 2005-02-01 Fasteners Torque/clamp force testing Éléments de fixation Essais couple/tension Reference number ISO 16047:2005(E)
More informationZero Point Clamping System. ZERO lock BALL lock
Zero Point Clamping System ZERO lock BALL lock kap3 kap 263 Technical information regarding ZERO lock Zero Point Clamping System Application The modularly designed, flexible ZERO lock Zero-Point Clamping
More informationConduit Assemblies. Complex Assembly - FLEXAquick System
ccessories Conduit ssemblies Conduit ssemblies Complex ssembly - FLEXquick System 236 Conduit ssemblies Simple ssembly Finished Products ccessories Conduit ssemblies 237 ccessories Conduits Conduits Straight
More information2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions
2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2.
More informationISO INTERNATIONAL STANDARD. Metallic tube connections for fluid power and general use Part 6: 60 cone connectors with or without O-ring
INTERNATIONAL STANDARD ISO 8434-6 First edition 2009-08-15 Corrected version 2010-05-01 Metallic tube connections for fluid power and general use Part 6: 60 cone connectors with or without O-ring Raccordements
More informationSCREW THREADS. = minor diameter. d 3. d 2. = pitch diameter
ISO : 6 Part 2 DIN : Part /20 Metric (ISO) screw thread, coarse series -M- T-00 T-002 for M to incl. M,4, fit H/6h The bold lines indicate the maximum material profiles. The maximum material profile of
More informationflexible couplings for pipe connections with axial restraint
www.arpol.com A R P O L F I X flexible couplings for pipe connections with axial restraint 1 TABLE OF CONTENTS Advantages & installation Sealing & anchoring system 4 5 Nominal charts 6 Material specifications
More informationManufacturing Instructions
May 2016 Manufacturing Instructions Assembly and disassembly SN 200-6 ICS 25.020 Dimensions in mm Supersedes SN 200-6:2010-09 Table of contents Page 1 Scope... 1 2 Normative references... 1 3 Terms and
More informationBALANTINE WALL-MOUNT FAUCET INSTALLATION
SKU(s): 911574, 911575 BALANTINE WALL-MOUNT FAUCET INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware
More informationISO INTERNATIONAL STANDARD. Hexagon bolts with flange with metric fine pitch thread Small series Product grade A
INTERNATIONAL STANDARD ISO 15072 First edition 1999-12-15 Hexagon bolts with flange with metric fine pitch thread Small series Product grade A Vis à tête hexagonale à embase cylindro-tronconique, à filetage
More informationMounting Instructions For 3-Piece Namur Style Mounting Bracket To 2-Way 60 Series Valves
Mounting Instructions For 3-Piece Namur Style Mounting Bracket To 2-Way 60 Series Valves NOTE: These instructions apply only to 60 series ball valves with bodies containing external mounting nibs. External
More informationSprinkler wet pipe and dry pipe. For FM approval of the dry pipe model "I" shall be used. SBF 120: 7 applies to model "E".
Product Name Nordic Flow FM Thin Wall Pipes Application Sprinkler wet pipe and dry pipe. For FM approval of the dry pipe model "I" shall be used. SBF 120: 7 applies to model "E". Manufacturing Standard
More informationThe MUELLER method of making a main to service connection using the MUELLER E-5 Small Drilling Machine. Hand or power. kpa/34.
MUELLER SMALL DRILLING MACHINES 2.1 Shaded area indicates change Rev. 9-09 MUELLER Co. manufactures several different small drilling machines for drilling holes from 7/16" to 2" in all types of pipe. Machines
More informationThread and Connector Identification
How to Use this Section This section is intended as an aid to identifying the most popular threads on hydraulic hose couplings and adaptors, and hydraulic equipment. BSP, Metric, American and Japanese
More informationbolts: G Cr-1/5Mo (A193 B7) 16 x M20 (EN ISO 4014) MPR GASKET 'SP' PETRO 4,0mm 363 x 323 x 4,5 mm (2 pieces)
test condition: 20 C 44 bar load condition 1: 206 C 18 bar load condition 2: 210 C 26 bar bolts: G41400 1Cr-1/5Mo (A193 B7) 16 x M20 (EN ISO 4014) gasket: MPR GASKET 'SP' PETRO 4,0mm 363 x 323 x 4,5 mm
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationFRAME BRACKET. Doing Our Best to Provide You the Best. Ford F250, F350 & F parts list. Page 1. 2/17 HJ32002,Rev 2.
2/17 HJ32002,Rev 2 BOlt torque specifications MEtRiC BOlts size Grade torque 8mm 8.8 23 ft/lbs. 10mm 8.8 45 ft/lbs. 12mm 8.8 78 ft/lbs. 14mm 8.8 125 ft/lbs. standard BOlts size Grade torque 5/16 5 18 ft/lbs.
More information1 Scope. 2 Normative references. 3 Dimensions. Page 2 DIN :
Page 2 1 Scope This standard specifies dimensions and technical delivery conditions for stud bolts with metric thread made of steel, stainless steel or nonferrous metal. 2 Normative references This standard
More informationAssmann Corporation of America TANK INSTALLATION AND USE GUIDELINES FOR BULK STORAGE TANKS
Assmann Corporation of America TANK INSTALLATION AND USE GUIDELINES FOR BULK STORAGE TANKS General Information Assmann polyethylene storage tanks are manufactured to give you the toughest, most reliable
More informationT : F : Revised June 2013
Revised June 2013 W R A, O USA T: 800 321 7950 440 998 2788 F: 440 992 2925... 2 INSTRUCTIONS FOR 3/4, 1, 1-1/4 DIAMETER TAPS FIGURE 1 A B C D E F G HOT TAP SPINDLE HOT TAP SLEEVE HOT TAP FEED SCREW ADAPTER
More informationThe MUELLER method of making a main to service connection using the MUELLER E-5 Small Drilling Machine. The main is drilled out under pressure.
MUELLER SMALL DRILLING MACHINES 2.1 Rev. 9-09 MUELLER Co. manufactures several different small drilling machines for drilling holes from 7/16" to 2" in all types of pipe. Machines are available in hand
More informationHandout Activity: HA043
Handout Activity: HA043 Student/Intern information: Name Date Class Summary There are many different fasteners used in automotive applications, including screws, bolts, studs & nuts. Washers & chemical
More informationPARTITION INSTALLATION INSTRUCTIONS
PARTITION INSTALLATION INSTRUCTIONS 2015 Chevrolet Tahoe PPV / Part Number 5703FW, FWA & FEW Do not attempt to install this product on any vehicle equipped with third row seating! Parts List Distributed
More informationHigh-quality pressure transmitter For general industrial applications Model S-10
Electronic pressure measurement High-quality pressure transmitter For general industrial applications Model S-10 WIKA data sheet PE 81.01 for further approvals see page 4 Applications Machine building
More informationThis installation guide applies to this part n /description: Amarok 4 cyl. Snorkel
4-cyl. 1570 0000 This installation guide applies to this part n /description: 1570 0000 Amarok 4 cyl. As on: 10.2017 Page 1 of 9 SEIKEL GmbH 4-cyl. Important To ensure proper function and optimal quality
More informationTWIN ROD CYLINDERS 6 CONTENTS
CAD drawing data catalog is available. ACTUATORS GENERAL CATALOG TWIN ROD CYLINDERS6 CONTENTS TWIN ROD CYLINDERS 6 Features 745 Specifications/Order Codes 747 Inner Construction and Major Parts 748 Dimensions
More information1/2/2016. Lecture Slides. Screws, Fasteners, and the Design of Nonpermanent Joints. Reasons for Non-permanent Fasteners
Lecture Slides Screws, Fasteners, and the Design of Nonpermanent Joints Reasons for Non-permanent Fasteners Field assembly Disassembly Maintenance Adjustment 1 Introduction There are two distinct uses
More informationNAVSEA STANDARD ITEM T9074-AS-GIB-010/271, Requirements for Nondestructive Testing Methods
NAVSEA STANDARD ITEM ITEM NO: 009-48 DATE: 29 JUL 2011 CATEGORY: II 1. SCOPE: 1.1 Title: Pressure Seal Bonnet Valve; repair (shop) 2. REFERENCES: 2.1 S9086-CJ-STM-010/CH-075, Fasteners 2.2. T9074-AS-GIB-010/271,
More information18000 HDL FOUR POST LIFT LB CAPACITY INSTALLATION AND OWNER'S MANUAL
18000 HDL FOUR POST LIFT 18000 LB CAPACITY INSTALLATION AND OWNER'S MANUAL WARNING! Do not raise a vehicle unless the front stops are in place, the parking brake is set, and the wheels are chocked. Stay
More informationISO INTERNATIONAL STANDARD. Fasteners Torque/clamp force testing. Éléments de fixation Essais couple/tension. First edition
INTERNATIONAL STANDARD ISO 16047 First edition 2005-02-01 Fasteners Torque/clamp force testing Éléments de fixation Essais couple/tension Reference number ISO 16047:2005(E) ISO 2005 PDF disclaimer This
More informationHusqvarna Construction Products North America Instruction Sheet: Sealed Blade Shaft Kit
Purpose: Installation of Sealed Bladeshaft Kit for models shown. Note: Modification of frame is required for retrofit onto older models. Models: Magnum Super Mag Special, Dimas FS6500, Magnum 38 Special,
More informationInstruction Sheet RADIO FREQUENCY SYSTEMS. Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) No Rev.
Instruction Sheet No. 412764 Rev. B ECO 12469 Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) These Installation Instructions are valid for antennas in the following version: reflector 2.4
More informationframe bracket Dodge x 2 & 4 x 4 (6-1/2 & 8 Boxes Includes Mega Cab)
, Rev 4 02/19 frame bracket 8552026 Dodge 3500 4 x 2 & 4 x 4 (6-1/2 & 8 Boxes Includes Mega Cab) 14 5 7 2 4 11 9 10 17 3 6 1 8 13 15 16 18 12 ITEM PART # DESCRIPTION QTY. 1 00085.50 FLAT WASHER 10 2 00248
More informationAccessories for sensors
Accessories for sensors Mounting and installation Adapters for pressure sensors: Hex AF width 27 ZBM 01 Adapter female thread G1/4 male thread G1/2 B, DIN EN 837-1 Part no.: 257276 Flat seal ring Cu 6.2x17.5x2.0
More informationSPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS
UDC 621.882.211 [669.14.018.291] IS : 3757-1985 (Reaffirmed 2003) Edition 3.2 (1989-07) Indian Standard SPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS ( Second Revision ) (Incorporating Amendment Nos.
More informationSpecification
Specification 2018-04 Class: Test Instruction, Conditions of delivery Class No.:61 Technical conditions of delivery for elastomer parts JED 220 Previous Edition Part name (for databases) 2015-06 Elastomer,
More informationTypical Group D Rear Acoustical Cover Installation
SERIES 60 SERVICE MANUAL 1. Gear Case Cover 5. Bolt 2. Gear Case 6. Acoustical Cover 3. Acoustical Cover Snap 7. Acoustical Cover 4. Acoustical Cover Clip 8. Nut Figure 1-179 Typical Group D Rear Acoustical
More informationJARVIS. Model Brisket Scissor EQUIPMENT... TABLE OF
Model 423-17 Brisket Scissor EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page Model 423--17... 4037003 Air Filter / Regulator / Lubricator 3022003 Air Hose Assembly... 3059018 Balancer...
More informationw w w. h d o n l i n e s h o p. d e AUTOMATIC COMPRESSION RELEASE TOOL GENERAL INSTALLATION -J04654 REV Kit Number Models
-J05 REV. 008-0- GENERAL Kit Number 98-08 Models AUTOMATIC COMPRESSION RELEASE TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationGB/T Translated English of Chinese Standard: GB/T NATIONAL STANDARD OF THE
Translated English of Chinese Standard: GB/T7307-2001 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 21.040.20 J 04 GB/T 7307-2001 eqv ISO
More informationLPK1550 Hydraulic Crimping Tool 15-ton
SERVICE MANUAL LPK1550 Hydraulic Crimping Tool 15-ton Serial Code FYF Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register
More informationOverview. Branched connection (using an o-let or saddle component) Profile (hole) cut into the pipe run. Pipe is not broken
Overview A piping component (to cut) for routed system is considered when the component is placed onto a pipe run and a profile cut occurs in the pipe route at the inserted point. See Content Center Piping
More informationAir Cooled Engine Technology. Roth 9 th Ch 2 Tools & Measuring Pages 21 43
Roth 9 th Ch 2 Tools & Measuring Pages 21 43 1. A combination wrench has one end and one end. Box & Open Square & Round Ratcheting & Gear 2. A or flare nut wrench is used on metal tubing connection fittings.
More informationSensyTemp TSBA (BA R) Resistance thermometer for building automation, machine construction and environmental engineering
Change from one to two columns Data Sheet 10/10-3.61-EN Rev. D SensyTemp TSB (B R) Resistance thermometer for building automation, machine construction and environmental engineering Measurement made easy
More informationIS INTERNATIONAL STANDARD. Slotted countersunk flat head screws (common head style) - Product grade A. Vis 9 mktaux d t&e fraisee fendue -
INTERNATIONAL STANDARD IS0 2009 Third edition 1994-04-01 Slotted countersunk flat head screws (common head style) - Product grade A Vis 9 mktaux d t&e fraisee fendue - Grade A Reference number IS0 2009:1994(E)
More informationInstallation and Operational Instructions for ROBA -DS couplings Type 95. _ (disk pack HF) Sizes
95. _ (disk pack HF) Sizes 6 22 Please read these Operational Instructions carefully and follow them accordingly! Ignoring these Instructions may lead to malfunctions or to coupling failure, resulting
More informationPressure transmitter for general industrial applications Model A-10
Electronic pressure measurement Pressure transmitter for general industrial applications Model A-10 WIKA data sheet PE 81.60 Applications Machine building Machine tools Measurement and control technology
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 8133 Third edition 2014-11-15 Hydraulic fluid power Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) compact series Transmissions hydrauliques Dimensions
More informationREPLACING THE CAT SEAL IN THE 90AD EXTRUDER
T S B D S D 0 0 0 4 T E C H N I C A L S E R V I C E B U L L E T I N REPLACING THE CAT SEAL IN THE 90AD EXTRUDER 1-8 0 0-2 7 8-3 3 5 3 w w w. j c s t e e l e. c o m 2018 J.C. Steele & Sons, Inc. SAFETY
More informationSURFACE VEHICLE STANDARD
400 Commonwealth Drive, Warrendale, PA 15096-0001 SURFACE VEHICLE STANDARD J365 Issued 1968-10 Revised 1994-08 REV. AUG94 Submitted for recognition as an American National Standard Superseding J365 FEB85
More informationAVK High Strength Blind Threaded Fasteners. Ideal for blind applications
High Strength Blind Threaded Fasteners Ideal for blind applications AVK Spinwall Technology How Hole Fill Works For You As the AVK insert is installed, the knurled body expands 360 to create hole fill.
More informationF l a t S c r e e n A R M S I n s t a l l a t i o n
ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)
More informationFord Couplings For Pipe And Tubing
Section J 6/2002 Ford Couplings For Pipe And Tubing The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260/563-3171 FAX: 1-800-826-3487 Overseas
More informationISO INTERNATIONAL STANDARD. Rolling bearings Accessories Part 2: Locknuts and locking devices Dimensions
INTERNATIONAL STANDARD ISO 2982-2 Second edition 2001-04-15 Rolling bearings Accessories Part 2: Locknuts and locking devices Dimensions Roulements Accessoires Partie 2: Écrous à encoches et dispositifs
More information