Mounting of poles and foundations Rette produkt Til rette opgave
|
|
- Collin Weaver
- 5 years ago
- Views:
Transcription
1 Mounting of poles and foundations Rette produkt Til rette opgave 12/04/2018
2 Burying and mounting poles General When mounting poles, the door of the pole must always match the specific pole, with which it was produced. This goes especially for conical poles where a number is found in both pole and door that indicates the affiliation. Be aware that it can be necessary to have isolation material between the foot of the pool and the bolts for poles with foundations. This is due to risk of galvanic corrosion caused by a big discrepancy in anodic value. It s recommended that poles for burying are accompanied by cable sleeve cuffs if no cable tubing is added. Poles with foot must have, as specified in EN 40, oversized washer acc. to ISO Foundation bolts for these poles should be fastened with a torque wrench acc. to size, steel type and eventual lubricant. Surface treatment Steel poles normally have 60µ of galvanization acc. to EN Winged foundations are made in alu-zinc which normally have 20-25µ alu-zinc corresponding to µ heat galvanization. Aluminum poles normally have 20-25µ anodizing. Mounting height In some cases, it can be necessary or an advantageous to change the depth of the hole. The door should as a base always be minimum 300 mm above terrain. Otherwise there is distinguished between 3 situations as specified below. Bolts over terrain, with the foot of the pole in the level of the terrain, makes maintenance easy. Density of soil Foundations placed 200mm under terrain. pole itself be visible. Furthermore the extra depth increases the stability of the pole. Placement of the pole 500 mm over terrain is sometimes used in parking spaces to protect the pole from collision. Here it s important to calculate the pole for a foundation going 500mm above terrain. The maximum deviation allowed is +20 mm. Be aware that security poles must be mounted specifically in relation to the soil. Loose soil Compressed soil Placement of the pole 200 mm under terrain is the aesthetic solution. 200 mm is enough to hide the foot of the pole and bolts, thus letting only the the
3 Mounting and placement Soil Poles are either for burying or foundation. Ready made foundations and poles for burying goes under the category of pile foundation. These derive their strength from the surrounding soil. It s therefore very important to guarantee the quality of the soil before the pole is mounted. Soil is usually classified as clay, silt and sand soils. The type of soil is determined by the grain size. Sand soil has a large grain size followed by silt and clay has the smallest. Each type of soil acts differently and it can thus be difficult to determine the bearing capacity of the soil. At Daintra we use stable gravel as standard soil. Burying and compression For burying poles, it s recommended that the hole dug is wider than 3 times the diameter of the largest width of the foundation. This ensures that the soil used as filler is responsible for the bearing capacity of the foundation. When mounting a pole in slanted terrain, it s recommended that a shoulder for the foundation is built with the depth of the foundation as a minimum radius. Before the foundation is placed a compressed layer of soil is made in the bottom of the hole. This can be done with stable gravel. The hole is adjusted to the burying mark on the pole for buried poles or the foundation. The compression is carried out acc. to the Eurocode. Typically, the soil is compressed in layers of mm using the appropriate methods such that the expected bearing capacity is acquired. Soil type Age Cu ϕ c' Peat Pg Gyttja Pg Clay Pg Sand Pg Clay Sg Melt w. clay Gc Met w. sand Gc Boulder clay Gc Moraine sand Gc Cu/c undrained/effective cohesion, ϕ friction angle, Pg post glacial, Sg late glacial, Gc glacial Stepped poles are adjusted with a bubble level either placed on the foot or the pole. For conical poles place a bubble level on the foot. To check conical poles, a block corresponding to the conicity of the pole is placed at 2 meters. Here, a bubble level can be placed for measuring. For poles placed in environments with damaging vibrations, a vibration dampener can be used. The pole is mounted directly at the foundation only if the surface is sufficiently even. For high poles and poles in risk of big vibration, any gap between the foot and the foundation should be filled with non shrinking concrete mortar. Areas of risk Be aware of the soil conditions. High groundwater reduces bearing capacity. Peat and other soils with high content of organic materials have high risk of displacement. The water content in clay has a big impact, since the clay can either become liquid or lose its cohesive properties. Mounting in frozen soil can result in displacements when heated. Casting of concrete foundation Foundation bolts are placed in a casting template, and then lowered into the wet concrete. The casting template rests on the concrete surface until the hardening has completed. Be aware that it takes the concrete 21 days to harden. Concrete quality: C25/30 or better. Reinforcement of the concrete has to be calculated. Mounting The casting template is removed and the nuts are fastened and leveled. Then the pole is mounted with washer and nuts. Bottom nut is placed 10 mm above the foundation. The foot must supported with concrete if the distance is more than 20 mm from nut to foundation. To minimize the risk of settlements in the soil it s recommended that the foundation is filled inside. For this, it s not needed to compress the soil. Notice that the wrong choice of compression in some cases could be harmful for the bearing capacity of the soil. Drain There must always be a drain for the pole. If the space between the foot and the foundation is full of concrete mortar a drain must be made to avoid water collection. This also goes for the bottom fill if it s made of concrete. Mounting and stabilization of pole When mounting cylindrical poles a bubble level is placed on the foot* or the pole for measurement. *Foundation placed in height of terrain
4 Steel foundations STEP 1 Before burying, check that the pole and foundation fit together. After, the foundation is buried according to aforementioned considerations, see ( Mounting and placement section). STEP 2 When mounting the foundation, the top nut and disc is removed. The nuts are adjusted such that the fitting plate is level. The pole is then mounted in level based on the buried foundation. Vibration dampeners can be attached between the pole foot and foundation plate. Remember isolation tubing on bolts for aluminum poles. STEP 3 Keep one nut of distance between the two bottom nuts for eventual fine tuning of the pole s inclination. Nuts are tightened with a torque wrench acc. to foundation specifications. Protection caps are attached to the bolts to secure a long life span.
5 Concrete foundations STEP 1 Before burying it is checked that the pole and foundation fits together. After, the foundation is buried according to aforementioned considerations, see ( Mounting and placement section). STEP 2 When mounting the foundation the top nut and disc is removed. The nuts are adjusted such that they are level. The pole is then mounted in level based on the buried foundation. Vibration dampeners can be attached between the pole foot and the bottom foundation nuts and discs. Remember isolation tubing on bolts for aluminum poles. STEP 3 Keep one nut of distance between the bottom nuts and the foundation for eventual fine tuning of the pole s inclination. Nuts are tightened with a torque wrench acc. to foundation specifications. Protection caps are attached to the bolts to secure a long life span.
6 Wing foundations STEP 1 Before burying it is checked that the pole and foundations fit together. Then the digging is done with attention to the potential risks. (see risks under Mounting and placement ). STEP 2 If two sets of wings are attached, they are to be placed over and under the cable exit and are turned 90 degrees in relation to each other. One in the bottom as far down as possible. One in the top 100 mm under the surface of the terrain. If only one set of wings, it s placed 100 mm under the terrain. STEP 3 The wings are attached with 4xM5 bolts and nuts. See accompanying bolt bag for size check. Can also be had with 2xM10 bolts. The pole is leveled in the dug out hole and the filler is compressed ( Mounting and placement ) Top/bottom wing foundation can also be replaced with concrete, universal or ring foundations.
7 Maintenenace General maintenance Movable parts by the door are lubricated once per year. Every fifth year it s recommended to conduct a visual inspection of the pole and its foundation. If necessary, the bolts and lock nuts are tightened. Galvanized surfaces If galvanized surfaces are damaged they must be repaired acc. to DS 1461 with paint containing zinc. Painted surfaces It s recommended to regularly wash/rinse painted surfaces of road salt and dirt. To prolong the durability wash with detergent containing wax. Hereafter a good wax is used for final treatment. This procedure is recommended to be done at least once a year. Damages are to be repaired as soon as possible after the damage is done. Thermoplastic surfaces Can be washed with environmentally friendly detergents. Scratches and cracks can be corrected with heat or repaired with thermoplastic material, which is applied with heat. Treatment of foundation bolts Foundation bolts must be lubricated with grease before mounting the pole. Hereafter it s recommended to use grease filled protection caps, in order to allow for easier tightening of the bolts later on. Retightening of the bolts should happen for the first time after 2-3 years, then every fifth year. Black foundation bolts can, in cases of corrosive environments, be lubricated with paint containing zinc. Galvanized or stainless bolts can also be ordered. In very corrosive environments or where further protection is desired, the bottom of the pole can get a root treatment until 200mm above terrain. The foot of the pole and bolts are treated with a C5 treatment. Protection caps for foundation bolts: Delivered in sets of 4 pcs. for i.a.: M20 bolts El. nr M24 bolts El. nr M27 bolts El. nr M33 bolts El. nr M39 bolts El. nr Anodized surfaces Anodized aluminum surfaces need a certain maintenance. The coating effectively protects against corrosion, wear and tear, and keeps the soil from depositing on the surface. In very polluted environments, such as industrial areas, it is necessary to periodically clean the poles to maintain their lifespan. In practice the frequency with which the poles are cleaned depends on how aggressive the environment is. It s best to clean with a neutral and synthetic detergent applied to a cloth or soft brush. Then the poles are to be washed with water. Hardened dirt can be removed with a light grinding detergent or shed fiber with neutral polishing powder. Always avoid sodium, bases and acids.
8 Frederiksværkvej 24 DK-3600 Frederikssund Tel
MERRY GO ROUND ITEM NO: 8030
MERRY GO ROUND ITEM NO: 8030 OWNER S MANUAL CAUTION: This unit is designed to be used safely by up to 4 children between the ages of 3 years to 8 years old with a maximum weight of 00 pounds (45.4 kgs)
More informationTHE HANDY GARDEN SHED. SNSD-E Owner s Manual
THE HANDY GARDEN SHED SNSD-E Owner s Manual 1 BEFORE YOU START Owner s Manual Prior to installation, it is important that you contact your local government authority to determine if building approval is
More informationEdgerail Aluminum Bridge Railing System Specification & Installation Instructions
Edgerail System Specification & Installation Instructions Hill & Smith, Inc 1000 Buckeye Park Road Columbus, Ohio 43207 Tel: 614-340-6294 Fax: 614-340-6296 www.hillandsmith.com Section A System Specification
More informationOptimast Installation Method Statement. F108.
Optimast Installation Method Statement. F108. Contents Page 1) Product Description. 2) Durability....... 3) Profile & Baseplate..... 4) Anchor Cradle and Foundation Stud Set Detail Drawings 4a) 127...
More informationINSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: ,
INSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: 2010-2014 CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: 32-21020, 32-21025 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 CONTOUR BAR TORQUE WRENCH 2 1
More informationIPA BESLAG FOR SCHÜCO ALU INSIDE NORDIC A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45)
IPA BESLAG FOR SCHÜCO ALU INSIDE NORDIC 2015 A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45) 98 35 15 00 3 FITTINGS FOR SCHÜCO ALU INSIDE NORDIC Table of contents PAGE SCHÜCO
More informationSYW Industry Sdn. Bhd. Stud Anchor. Hexagon Nut / Flange Nut. U - Bolt (c/w 2 Nuts) Steel Band. 1 of 8
SYW Industry Sdn. Bhd. Stud Anchor Hexagon Nut / Flange Nut U - Bolt (c/w 2 Nuts) Steel Band 1 of 8 BT Anchor (MM size) Expansion Anchor 2 of 8 Set Anchor Sleeve Anchor with Flange Nut 3 of 8 BT Anchor
More informationIPA FITTINGS FOR SCHÜCO ALU INSIDE NORDIC A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45)
IPA FITTINGS FOR SCHÜCO ALU INSIDE NORDIC 2017 A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45) 98 35 15 00 3 FITTINGS FOR SCHÜCO ALU INSIDE NORDIC Table of contents PAGE SCHÜCO
More informationAdjustable Feet Castors Accessories for Floor Elements
Adjustable Feet Castors Accessories for Floor Elements Products in this section Levelling Knuckle Feet Threaded spindles for infinite height adjustment Metal or plastic foot plate Knuckle Feet X Compatible
More informationINSTRUCTION MANUAL Q-HYDRAULIC
Dat: 15.04.02 No: 94-BA 5039E/1b TABLE OF CONTENTS Part III 3.0 Type code explanation 3.1 Service connections 3.2 Impeller clearance adjustment 3.2.1 Wear of wearing parts 3.2.2 General notes to adjustment
More informationSprinkler wet pipe and dry pipe. For FM approval of the dry pipe model "I" shall be used. SBF 120: 7 applies to model "E".
Product Name Nordic Flow FM Thin Wall Pipes Application Sprinkler wet pipe and dry pipe. For FM approval of the dry pipe model "I" shall be used. SBF 120: 7 applies to model "E". Manufacturing Standard
More informationPLAY HOUSE IMPORTANT
IMPORTANT Page 1 PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationUSER MANUAL Nord-Lock X-series washers
USER MANUAL Nord-Lock X-series washers JOINT GUIDE 3 ASSEMBLY INSTRUCTIONS 4 TECHNICAL DATA 5 TORQUE GUIDE 5 THE EXCEPTIONAL SYSTEM THAT PREVENTS BOLT LOOSENING AND SLACKENING Nord-Lock X-series washers
More informationThread protection accessories are installed at the MODIX production factory and delivered with couplers.
Installation of MODIX Rebar Coupler Identification of the product The type of MODIX Rebar Coupler can be identified by the marking on the product. Size of the Coupler can be identified also according to
More informationRoller Guides C-Rail Systems Linear Guide Systems Ball-Bearing Guide Bushes Ball-bush block guides Shafts Accessories for Linear Slides
Roller Guides C-Rail Systems Linear Guide Systems Ball-Bearing Guide Bushes Ball-bush block guides Shafts Accessories for Linear Slides Application example linear systems, drives and accessories 1 2 3
More informationSpiral Slide
IMPORTANT Page 1 PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationinstallation guide 1 GUIDE#: PWB-wwpontoon-pol-004
f250 pontoon WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This WakeWorks tower fits Pontoon boats with 96 to 102 inch wide beam widths. This measurement is taken from
More informationLeveling Feet, Base Plates and Casters
Leveling Feet, Base Plates and Casters 77 Leveling Foot 1 1 Fastening to profile end Fastening in T-slot of profile For leveling tables and light equipment. Ratchet-type height adjustment requires no tools.
More informationPLANISHING HAMMER STAND OWNER S MANUAL
PLANISHING HAMMER STAND OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious
More informationH O O P RAC K. Simple Security
H O O P RAC K Simple Security The Hoop Rack is a proven design that provides high security and easy bike parking. The Hoop Rack uses thick pipe construction and the full radius of the bend makes the Hoop
More informationDowntown Rack. Custom logo option available
Custom logo option available Downtown Rack The Downtown Rack uses thick, square-tube construction that can t be cut with a pipe cutter. The extended width of the Downtown Rack makes for easy bike parking
More informationStreet Design. MALL seating. Mall bench product details. Mall technical specification. Mall accessories. Mall material finishes
Street Design established in 1986 UK street furniture designers & manufacturers, Leicestershire LE12 8LD Contact us MALL seating As UK based, designers and manufacturers, Street Design can manufacture
More informationMAST ARMS & POLES. Ornamental Pole Top & Bases
Ornamental Pole Top & Bases Pelco s decorative pole top and bases make the traffic signal aesthetically pleasing to the eye. In addition to the standar 4-piece, Pelco also manufactures the bases with an
More informationBASEBALL FOUL POLES GROUND SLEEVE MOUNTED
X X Page 1 of 6 GROUND SLEEVE INSTALLATION Ground Sleeve Foul Pole Size "A" F39901 32' and 40' 67 5/8" F39902 24' 67 5/8" F39903 16' 43 5/8" 00402000 12' 29 3/8" 7" ONE SET OF SLOTS MUST BE PARALLEL AND
More informationNew Product Release: October 2014 Boone Racks
New Product Release: October 2014 Boone Racks Double Fido Fountain Mounting: Surface NOTE: THESE ROUGH-IN DIMENSIONS MAY VARY ½: (13 mm) PLUS OR MINUS NOTE: All dimensions subject to manufacturing variance
More informationH HD Adult Wheelchair Swing Frame & Hangers(perm) IMPORTANT
Page 1 IMPORTANT PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationStreet Design. BUCKLAND seating. Buckland bench product details. Buckland technical specification. Buckland accessories. Buckland material finishes
Street Design established in 1986 UK street furniture designers & manufacturers, Leicestershire LE12 8LD Contact us BUCKLAND seating As UK based, designers and manufacturers, Street Design can manufacture
More informationAssembly instructions
Assembly instructions SF 55 / SF 55c SF 75 / SF 75c / SF 75H A B B C D Scope of delivery: Safety instructions: A. Top rail B. Vertical profile C. Floor rail D. Hinged panel, sliding panel Accessories pack
More informationInstallation Instructions TMW Antenna Tower Mount for 4ft (1.2m) Antennas.
Description The following pages show the steps required to assembly and fit the antenna mount to a vertical tower pipe of diameter 48 to 115 mm (1.9 to 4.5"). This mount provides ±20 azimuth or ±15 elevation
More informationSwerve Rack CUSTOM RACKS AVAILABLE
CUSTOM RACKS AVAILABLE Swerve Rack The design of the Swerve mirrors the bike frame, thus providing superior bike support while making it easy to secure both the bike frame and wheel with a standard u-lock.
More informationPV-ezRack PostMount 1-A Installation Guide
PV-ezRack PostMount 1-A Installation Guide NO.: PZ10A -IM06-10 Version:V1.0 Editor: Edit date: Check by: Audit by: Approve by: File record Content Editor Date V1.0 English Bronze 2015.4.17 CONTENT 1. Introduction..
More informationS W E RV E RAC K. Simple Security. Simple Stability.
S W E RV E RAC K Simple Security. Simple Stability. The Swerve Rack is a proven design that provides high security and easy bike parking. The Swerve Rack uses thick pipe construction and the full radius
More informationINSTALLATION INTRUCTIONS
INSTALLATION INTRUCTIONS Page 1 of 9 Installation Instructions 1. 2. Check all items against parts list to ensure all parts have been included (see pages 6,7,8,9). Locate and drill holes for concrete footings.
More informationInstalling a COMROD AS1R Whip Antenna with Anchor Post
Installing a COMROD AS1R Whip Antenna with Anchor Post IS10012 Issue 1.0...15 September 2010 Nautel Limited 10089 Peggy's Cove Road, Hackett's Cove, NS, Canada B3Z 3J4 T.877 6 nautel (628835) or +1.902.823.2233
More informationHEICO FASTENING SYSTEMS. Simple Fast Reliable HEICO-TEC TENSION NUT
HEICO FASTENING SYSTEMS Simple Fast Reliable HEICO-TEC TENSION NUT WWW.HEICO-TEC.COM HEICO-TEC TENSION NUT SIMPLE FAST RELIABLE For a secure joint with a HEICO-TEC tension nut, no electric, hydraulic,
More informationBi-partite gouge auger model P
Bi-partite gouge auger model P Manual Meet the difference Eijkelkamp Soil & Water Nijverheidsstraat 30, 6987 EM Giesbeek, the Netherlands T +31 313 880 200 E info@eijkelkamp.com I www.eijkelkamp.com 2018-07
More informationDatasheet: Douglas Fir Swing Frame suspension height 2,50 m (Art.-No ) incl. post shoes
Datasheet: Douglas Fir Swing Frame suspension height 2,50 m (Art.-No. 4577-1-250) incl. post shoes 1 Space required: 4.20 x 4.00 m, safety area: 4.20 x 8.20m Height of fall 2.35 m 2 Surface material Description
More informationAGILITY. ROTA WEB CLIMBER 3.3m PROD. CODE SIZE AGE RANGE F/ FALL HEIGHT HEAVIEST PART TOTAL WEIGHT ROTAWEB33. 8 TO mm 73kg 115kg
AGILITY ROTA WEB CLIMBER.m PROD. CODE SIZE AGE RANGE F/ FALL HEIGHT HEAVIEST PART TOTAL WEIGHT Dia. m x.m High 8 TO 4 00mm 7kg 5kg SPECIFICATION Centre Upright: Made from 6" diameter aluminium tube to
More informationInstructions for Fitting, Operating and Maintenance
EN Instructions for Fitting, Operating and Maintenance Side hinged door / GDP Personnel Door 1 327 010 RE / 05.2011 ENGLISH Contents 1 Safety Instructions... 3 1.1 Qualified persons... 3 1.2 Symbols and
More informationInstallation & Owner's Manual
Step N Tilt Lawn Aerator 2 The Easy Way to Revitalize Your Lawn Installation & Owner's Manual 2013 Model SNT99 U.S. Patent Pending May be used with two or four tines With optional soil core container IMPORTANT:
More informationSIGNALS AND LIGHTING FIELD GUIDE
CHAPTER 16 SIGNAL AND LIGHT POLES SIGNAL AND LIGHT POLES The standards and requirements for installing traffic control signal and light poles are presented in this chapter. 16.1 Traffic Control Signal
More informationPlanishing hammer stand For use with SKU Planishing hammer
Planishing hammer stand For use with SKU 94847 Planishing hammer Model 96300 Assembly And Operation Instructions Please Note: Planishing Hammer not included with Stand. Due to continuing improvements,
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationMODEL 2EA/2EB DOOR INSTALLATION INSTUCTIONS
Dover Roller Shutters wants to THANK YOU for your purchase of the 2EA/2EB Aluminum Roll-Up Door! BEFORE INSTALLATION Please carefully read the instruction manual completely. Carefully unpack the contents
More informationN35 ALUMINIUM ROLL-UP DOOR INSTALLATION MANUAL
N35 ALUMINIUM ROLL-UP DOOR INSTALLATION MANUAL DOVER ROLLER SHUTTERS 295 COMMERCE WAY P.O. BOX 420 UPPER SANDUSKY, OH 43351 Dover Roller Shutters wants to THANK YOU for your purchase of the N35 Aluminum
More informationRotaplay Rock 'n' Bowl
Rotaplay Rock 'n' Bowl PROD. CODE SIZE AGE RANGE F/ FALL HEIGHT HEAVIEST PART TOTAL WEIGHT Ø065mm x 820mm High 2-0 Years 920mm.5 Kg 05 Kg SPECIFICATION Solid steel components made from steel to BS 970
More informationWith time, the evolution of anchors have led to different designs More than one anchor type may be suitable for a particular purpose Thus there are
Supreme range of Soil & rock anchors Introduction Used to anchor into concrete, masonry, stone With time, the evolution of anchors have led to different designs More than one anchor type may be suitable
More informationKD Table Base Assembly and Top Attachment Instructions
KD Table Base Assembly and Top Attachment Instructions 4011xx 5000xx 7014xx 8001xx 8206xx Congratulations on the purchase of your Tropitone furniture. Read through all steps before starting assembly. CAUTION:
More informationA Disc Golf Course Is Built in Three Phases
Instructions for Building a DiscGolfPark This guide contains detailed installation instructions for each DiscGolfPark product: DisCatcher target, InfoBoard, TeeSign and TeePad. Installing DiscGolfPark
More informationOwner's Manual & Assembly Instructions
BO01 Owner's Manual & Assembly Instructions PATIO COVER/CARPORT Model No. PC1010 Attached 705221006 UNIT DIMENSIONS *Size rounded off to the nearest foot CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST
More informationNAVSEA STANDARD ITEM
NAVSEA STANDARD ITEM FY-19 DATE: 01 OCT 2017 CATEGORY: I 1. SCOPE: 1.1 Title: Threaded Fastener Requirements; accomplish 2. REFERENCES: 2.1 Standard Items 2.2 S9086-CJ-STM-010/075, Fasteners 3. REQUIREMENTS:
More informationOne-sided rack, hot-dip galvanized Space between bicycles 350 mm length approx.kg Part-No. Two-sided rack, hot-dip galvanized
Bicycle rack Sturdy and space-saving due to alternating high and low racks. Racks can be bolted to form a serial system, with boreholes for anchoring or plugging. Bicycle parking rack Frame of angular
More informationPROformanceHoops.com
PROformanceHoops.com WHAT MAKES US DIFFERENT? We promote quality family playtime, fitness and fun by delivering your family the safest, most stable and most durable in-ground basketball hoop in the industry.
More informationHorizontal Cable Systems
ALUMINUM RAILING INSTALLATION INSTRUCTIONS v2012 orizontal Cable Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 1A) Coastal applications:
More informationBMW E46 Coupe 3dr MP Bolt in (BMW Race Days Only) Roll Cage (B045) Fitting Instructions
BMW E46 Coupe 3dr MP Bolt in (BMW Race Days Only) Roll Cage (B045) Fitting Instructions Unwrap the mounting points/ends of the roll cage and unpack the individual fitting kits. Try to leave wrapping on
More informationS-BT screw-in stainless steel and carbon steel threaded studs
S-BT screw-in stainless steel and carbon steel threaded studs Product data Dimensions S-BT-MR M10/15 SN 6 S-BT-MR M10/15 SN 6 AL**) S-BT-MR W10/15 SN 6 S-BT-MR W10/15 SN 6 AL**) S-BT-MR M10/15 SN 5 ***)
More informationLand Rover Defender 90/110/ th Anniversary Style Front Cage Fitting Instructions
Land Rover Defender 90/110/130 60 th Anniversary Style Front Cage Fitting Instructions Cambridge House Unwrap the roll cage and unpack the individual fitting kits. At this point it is recommended that
More informationINSTALLATION INSTRUCTIONS
PART NO. 911000T 911000PS 915000T 915000PS PRODUCT DESCRIPTION: Sport Bar 2.0, Full size Textured Black Sport Bar 2.0, Full size Polished Stainless Steel Tubes Sport Bar 2.0, Mid size Textured Black PRODUCT
More informationWALCOOM. Walcoom Corporation POST ANCHOR.
WALCOOM Walcoom Corporation Walcoom is a corporate that specialized in producing and selling various wire mesh and relative accessories. The production base of Walcoom Corp. is located in Anping county,
More informationPost & Rail. Includes: Crossbuck, 2-Rail, 3-Rail and 4-Rail POST SUPPORT OPTIONS
Post & Rail Includes: Crossbuck, 2-Rail, 3-Rail and 4-Rail STAGGER RAIL ENDS FOR GREATER STRENGTH ALLOW 1-1/2" GAP ON HINGE SIDE OF GATE AND 1-1/4" ON LATCH SIDE OF GATE HARDWARE DIG HOLES 30" MINIMUM
More informationWave Bike Rack specs SPECS AND INSTALL INSTRUCTIONS. Deluxe Wave Style Bike Rack. Series Names & Model # s. Product maintenance. Thermoplastic Coating
SPES ND INSTLL INSTRUTIONS Deluxe Wave Style ike Rack SKU: Series Names & Model # s 8 F7WIRQ InGround Post Mount Wave ike Racks Wave ike Rack specs KP/G3, KP/G5, KP/G7, KP/G9, KP/G11, KP/G13 Plate Surface
More informationdesignmasterfence.com
designmasterfence.com > INDEX > WHAT IS DESIGNMASTER? > PRODUCTS APPLICATIONS 2 3 > CLASSIC FENCE PANEL Specs & Advantages > CLASSIC FENCE POST Specs, Advantages & Installation > BRACKETS & ACCESSORIES
More informationFENCE INSTALLATION GUIDE 8 HIGH WALLS
FENCE INSTALLATION GUIDE 8 HIGH WALLS 1.866.648.9336 www.simtekfence.com INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers of SimTek decorative
More informationWALCOOM. Walcoom Corporation SAFETY GRATING.
WALCOOM Walcoom Corporation SAFETY GRATING Diamond-Strut Safety Grating Diamond-Strut safety grating is made of carbon steel, stainless steel or aluminum by cold forming. It can be divided into three types:
More informationCreate cable assemblies to fit your style
2015 Feeney (11/15) Quick-Connect Brochure #2015-975B Create cable assemblies to fit your style Quick-Connect Solutions Guide The fast and easy way to create your own CableRail assemblies! Our CableRail
More informationTelephone: Fax: Web site:
Street Design established in 1986 UK street furniture designers & manufacturers, Leicestershire LE12 8LD Contact us BEXLEY seating As UK based, designers and manufacturers, Street Design can manufacture
More informationAlways be your solar support
Always be your solar support Installation Manual CG ground mounting system Version 2016 1.0 www.antaisolar.com Contents 一.Product Introduction... 2 二.Installation Tools & Equipment... 3 三.System Components...
More informationGrand Slam 370 Installation Instructions
Grand Slam 370 Installation Instructions Patent #7,114,283 TACO Metals Inc., 50 NE 179 Street Miami, Florida 33162 info@tacomarine.com TACOmarine.com Your Kit Contains 2- Grand Slam 370 mounts 4-5/16"
More informationOperating manual. TruTool N 500 (1A1) english
Operating manual TruTool N 500 (1A1) english Table of Contents 1. Safety...4 1.1 General safety information...4 1.2 Specific safety information...5 2. Description...6 2.1 Correct use...7 2.2 Technical
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Gen II Mount System For 2011-2012 Dodge Ram HD 4500/5500 Bracket Kit 90160 Your safety, and the safety of others, is very important. To help you make informed decisions
More informationDual Arm Tilt LCD Mount
Installation Manual model # 51324 M o u n t i n g S y s t e m s Dual Arm Tilt LCD Mount Fits Displays 13 to 32 Supports Up to 50 lbs (23 kgs) Projection from Wall from 3 to 17 Meets VESA Standards 50/75/100,
More informationOperator's manual. TruTool N 1000 (1B1) english
Operator's manual TruTool N 1000 (1B1) english Table of contents 1. Safety...4 1.1 General safety information...4 1.2 Specific safety information...5 2. Description...6 2.1 Intended use...7 2.2 Technical
More informationH O O P RAC K. Simple Security
H O O P RAC K Simple Security The Hoop Rack is a proven design that provides high security and easy bike parking. The Hoop Rack uses thick pipe construction and the full radius of the bend makes the Hoop
More informationTAPTITE Fasteners. High Performance Thread Rolling Screws for Metals
TAPTITE 2000 Fasteners High Performance Thread Rolling Screws for Metals TAPTITE 2000 thread forming technology joins two unique concepts and advances fastener performance to new levels. TAPTITE 2000 fasteners
More informationAssembly instructions TerraWing Foundation System
Industriell Effektivitet i Terrängen TM Rev: Date: Nyköping 2014-11-26 Assembly instructions TerraWing Foundation System Copyright 2014 TerraWing AB Thank you for choosing the TerraWing Foundation System
More informationFS Uno mounting instructions. 2 Pile driving (Ramming) 5. 6 Components list Torque specifications 15
FS Uno System Mounting instructions CONTTS Page 1 General - Safety, planning and tools 2 2 Pile driving (Ramming) 5 3 Rack overview - Components and fasteners 6 4 Mounting of the individual assembly groups
More informationInstruction Manual for installing
Instruction Manual for installing Preloaded (HSFG) Bolting with TurnaSure DIRECT TENSION INDICATORS CE Marked EN 14399-9 TurnaSure LLC TABLE OF CONTENTS Introduction... 1 Theory of Preloaded Bolting Assemblies...
More informationCAVALIER. Shower Door Installation Instructions
CAVALIER Shower Door Installation Instructions IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More informationSECTION SITE FURNISHINGS FOR CFCRT. 1. American Society for Testing and Materials (ASTM).
PART 1 - GENERAL 1.1 SECTION INCLUDES A. Benches. B. Trash receptacles. C. Bike storage. 1.2 REFERENCE STANDARDS A. Including but not limited to: 1. American Society for Testing and Materials (ASTM). 1.3
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Brush Guard Kit Kit no. 67730 (black), 67731 (stainless) for GMC Trucks Your safety, and the safety of others, is very important. To help you make informed decisions about safety,
More informationHOME GYM Owner s Manual
HOME GYM Owner s Manual Content Content-------------------------------------------------------------1 Safety precautions----------------------------------------------------2 Assembly instruction-------------------------------------------------3-12
More informationInstallation of HORIZONT and HORIZONT HIGH pool enclosures
Installation of HORIZONT and HORIZONT HIGH pool enclosures Rev. 19.10.2017 PARTS LIST Parts for rail installation: Rail screw 6 x 60 Plastic anchor 10 x 50 Rail connector Arrest wedge [R-L] Pop rivet 4
More informationSECTION MASONRY ANCHORAGE AND REINFORCEMENT. Display hidden notes to specifier. (Don't know how? Click Here)
PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 04080 MASONRY ANCHORAGE AND REINFORCEMENT Display hidden notes to specifier. (Don't know how? Click Here) A. Post installed masonry anchors. B. Miscellaneous
More informationmiramondo Technical Informations 1/6 Passepartout Concrete
1/6 Passepartout Concrete Technical Informations Passepartout Concrete 2/6 Dimensions 590 600 1785 590 600 1785 250 150 400 700 Hole pattern for mounting 590/1785 504/1699 43 590 324 133 D 12 Passepartout
More informationDisclaimer. Socket Products Socket depth limits maximum torque. Torque figures are based on 80% of maximum torque for a given key size.
E546 V3 (1/17) Disclaimer Torque values listed in this book are based on mathematical calculations and experimental data. The values are valid only when the matched strength system listed is used. The
More informationUP139 CRUISE-A-LONG (STANDARD) NATURAL COATED DECK COATED RAMP DESCRIPTION SQUIRREL PANEL BACK WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL 90 AN
UP39 CRUISE-A-LONG (STANDARD) NATURAL COATED DECK COATED RAMP DESCRIPTION SQUIRREL PANEL BACK WALL CLEAR BUBBLE CRUISE RAIL SQUARE SPIRAL WHEEL 90 ANGLE BRACKET TUBE BRACKET TUBE WARNING LABEL PLATE HARDWARE
More informationInstallation Instructions
Installation Instructions Playworld Systems Model XX1407 Square Picnic Table w/coated Top & Frame Installation Preparation Recommended Crew:...Two (2) adults Installation Time:...1 man-hour Assembly View
More informationinstallation guide 1 GUIDE#: pwb-wwtowv1-pol-003
g300 WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This WakeWorks wakeboard tower fits motor boats with 76-108 inch wide beam widths. This measurement is taken from the
More informationMANUAL FOR. SHAFT GROUNDING ASSEMBLY WITH mv-meter AND AMPLIFIER FOR ALARM OUTPUTS
MANUAL FOR SHAFT GROUNDING ASSEMBLY WITH mv-meter AND AMPLIFIER FOR ALARM OUTPUTS BAC ORDER NO: 539600 Copyrigth: BAC CORROSION CONTROL A/S Færøvej 7-9 DK-4681 Herfølge Denmark telephone +45 7026 8900
More informationInstallation and Operational Instructions for ROBA -DS couplings Type 95. _ (disk pack HF) Sizes
95. _ (disk pack HF) Sizes 6 22 Please read these Operational Instructions carefully and follow them accordingly! Ignoring these Instructions may lead to malfunctions or to coupling failure, resulting
More informationSILICONE RESIN PAINT FOR MASONRY FACADES
TIKKURILA SILICONE RESIN PAINT FOR MASONRY FACADES DESCRIPTION Water-borne silicone emulsion paint. RECOMMENDED USES Residential, commercial, industrial and storage buildings and others. PRODUCT FEATURES
More informationTO O L K IT. Public Bike Repair
TO O L K IT Public Bike Repair The Dero Tool Kit includes all the necessary tools to perform most routine maintenance and adjustments on most bikes. All the tools are securely fastened with stainless steel
More informationStreet Design. CAMBERLEY seating. Camberley bench product details. Camberley seat product details. Camberley technical specification
Street Design established in 1986 UK street furniture designers & manufacturers, Leicestershire LE12 8LD Contact us CAMBERLEY seating As UK based, designers and manufacturers, Street Design can manufacture
More informationInstallation Manual Flat Track Series
Manual Flat Track Series Contents Safety...1 Parts...2 Hardware.......................................... 2 Tools Required..................................... 4.............................................
More informationFasteners. Metal Fasteners, Joining, and Adhesives. Bolts. Metal Fasteners, Joining, and Adhesives
Metal Fasteners, Joining, and Adhesives Fasteners Metal assemblies are often held together with fasteners, hardware devices that mechanically join or affix two or more objects together. Assembling with
More informationTechnical Manual. ETP-CLASSIC incl type R. Content
Technical Manual ETP-CLASSIC incl type R Content Technical parts description...2 Mounting/dismantling tips...4 Design suggestions...7 Tolerances...13 Central bolt...15 Torsional stiffness...16 Screw pitch
More information67-72 GM SHORT FLEETSIDE STEEL FLOOR TO WOOD FLOOR CONVERSION PART LIST: REQUIRED FOR CONVERSION DESCRIPTION
JAZ:instructions\instruct\67-72conv.pm6 pg 1 67-72 GM SHORT FLEETSIDE STEEL FLOOR TO WOOD FLOOR CONVERSION PART LIST: REQUIRED FOR CONVERSION QTY DESCRIPTION 1 Set Bed Strips 1 Set Bed Wood 1 Each Bed
More informationClamping devices 521
Clamping devices 521 522 Product overview Clamping devices Adjustable straps K0001 Hook clamps K0012 Goose-neck straps with long slot K0002 Page 526 Hook Clamps with collar K0013 Page 535 Equipped clamps
More informationPART MATERIALS. Section Fencing Materials. Description
PART 03000 - MATERIALS Section 03010 - Fencing Materials Description 03010.00 Scope - This section consists of the test requirements, specifications and tolerances for barbed wire, woven wire and chain
More informationTrunnion bearing housings for grinding mills FSDR.. K series
Trunnion bearing housings for grinding mills FSDR.. K series Bearing types Spherical roller bearings Bearing dimension series 39, 48 and 49 Shaft diameter range 825 to 1 460 mm Typical bearing-shaft combinations
More information