IPA FITTINGS FOR REHAU NORDIC

Transcription

1 IP FITTINGS FOR REHU NORDIC DESIGN PLUS 2017 /S J. PETERSENS BESLGFBRIK JCOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45)

2

3 3 FITTINGS FOR REHU NORDIC DESIGN PLUS Table of contents PGE REHU Nordic Design Plus profile 4 Suggestion - Number of Hinges 6 Suggestion - Hinge Positions 7 FITTINGS IP No Window hinge 8 IP No Doorhinge for top mounting 9 IP No djustable Door hinge 9-10 IP No Threated Plate 9-10 IP No Side swing window - adjustable IP No Top swing fi tting IP No Safety Restrictor IP No djustable Canopy Stay IP No djustable Canopy Stay - djustable Friction IP No Safety Restrictor IP No Friction Stay for Windows 23 IP No Friction Stay for Doors 24 IP No Support Fitting 25 IP No Guide Block 25 IP No Casement Hook IP No Casement Hook IP No Hook Catch IP No Casement Fasteners Lubrication Instructions /05

4 4 REHU NORDIC DESIGN PLUS PROFILE FITTING INSTRUCTIONS

5 5 REHU NORDIC DESIGN PLUS PROFILE IP HS IN COOPERTION WITH REHU DEVELOPED SERIES OF FITTINGS FOR THE REHU NORDIC DESIGN PLUS PROFILE.

6 6 FITTING SUGGESTION INSTRUCTIONS - NUMBER OF HINGES The charts below show the number of hinges, we suggest to use on different sizes of windows and doors. The charts shall ONLY be considered as a guidance, as the number of hinges also will depend on the use and weight of the window/door. If the window/door is mounted in a public building with many users (Schools, Railway Stations etc.) then more or even larger hinges are recommended. lso we suggest to use a support fi tting whenever possible. WINDOW HINGES: Valid for the window hinges shown in this catalogue. ll window hinges meets the requirements of class 9 (60 Kgs.) in accordance with DS/EN The numbers in brackets are number of hinges in windows with 3-layer glass. Width Height < (3) 3 (3) 3 (3) 3 (4) (3) 3 (3) 3 (3) 3 (4) (3) 3 (3) 3 (3) 3 (4) (3) 3 (3) 3 (3) 3 (4) (3) 3 (3) 3 (3) 3 (3) (2) 2 (2) 2 (2) 3 (3) (2) 2 (2) 2 (2) 3 (3) (2) 2 (2) 2 (2) 3 (3) (2) 2 (2) 2 (2) (2) 2 (2) < (2) DOORHINGES: Valid for door hinges shown in this catalogue. ll door hinges with steel pin meets the requirements of class 13 (120 Kgs.) in accordance with DS/EN The same hinges with brass pin meets the requirements of class 11 (80 Kgs.) in accordance with DS/EN 1935 Width Height < <

7 7 SUGGESTION - HINGE POSITIONS TTENTION: The suggested placement of the hinges is ONLY a recommendation. When mounting Window - or Door elements in buildings the fastening points of the Frame should be by the hinges, supporting the Frame as best as possible in the areas where the load from the sash/door is transferred to the Frame

8 4.5 8 WINDOW HINGE IP NO C ORDERING NO. MTERIL SURFCE IP NO. STEEL FIXED STEEL PIN SQURE EDGES LEFT SQURE EDGES RIGHT ELECTROPL. + GREY IP NO FITTING INSTRUCTIONS REHU NORDIC DESIGN PLUS: 11.8 ELECTROPL. + WHITE 2.2 GLVNIZED INDUSTRY PCKING IN BOXES OF 100 PCS. MM B MM C MM MTERIL MM PIN MM SCREW PPROX. WEIGHT KGS / PIECES ,5 8 4,0 0,19 B FIG. 1 FIG USE SCREW NO MINTENNCE: TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - GRESE THE PIVOT/MOVBLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER GRESE MINIMUM TWICE YER. SEE LSO INSTRUCTIONS ON PGE

9 9 DJUSTBLE DOOR HINGE IP NO , IP NO & IP NO C ORDERING NO. MTERIL SURFCE IP NO. STEEL FIXED STEEL PIN SQURE EDGES LEFT SQURE EDGES RIGHT GLVNIZED STNDRD PCKING IN BOXES OF 50 PPIECES MM B MM C MM MTERIL MM PIN MM SCREW PPROX. WEIGHT KGS / PIECES ,5 5,0 0,39 DJUSTBLE VERTICLLY B RIGHT THRETED PLTE B ORDERING NO. IP NO. MTERIL STEEL W/O SPECIFICTION SURFCE ELECTROPLTED STNDRD PCKING IN BOXES OF 10 PIECES MM B MM MTERIL MM THRETED HOLES MM PPROX. WEIGHT KGS / PIECES ,02 DOOR HINGE FOR TOP MOUNTING ORDERING NO. MTERIL SURFCE B IP NO. STEEL LEFT RIGHT ELECTROPL. + GREY ELECTROPL. + WHITE GLVNIZED STNDRD PCKING IN BOXES OF 10 PIECES MM B MM MTERIL MM SCREW PPROX. WEIGHT KGS / PIECES ,5 4,0 0,11

10 IP NO.s & FITTING INSTRUCTIONS REHU NORDIC DESIGN PLUS: FIG. 3 FIG UPPER HINGE PRT 18 LOWER HINGE PRT CUT OUT FOR THRETED PLTE THRETED PLTE IP NO FIG. 1 FITTING: ON LRGE DOORS IT IS RECOMMENDED TO USE THE THRETED PLTES IP NO THESE RE CUT INTO THE PROFILE ON THE BCK OF THE FRME. USE SCREWS NO. 5 FOR THE TWO THRETED HOLES. SEE FIG. 4 ND 5. DJUSTMENT: THE HINGE IP NO CN BE DJUSTED VERTICLLY TO WNTED POSITION BY TURNING THE SCREW IN THE BOTTOM OF THE HINGE ±3 MM. FIG. 4 THRETED PLTE MINTENNCE: TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - GRESE THE PIVOT/MOVBLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER GRESE MINIMUM TWICE YER. SEE LSO INSTRUCTIONS ON PGE FIG. 5

11 SIDE SWING WINDOW 90 0 DJUSTBLE IP NO.s ORDERING NO. MTERIL SURFCE IP NO. STEEL LEFT RIGHT ELECTROPLTED STNDRDPCKING IN BOXES OF 5 SETS MM B MM SCREW PPROX. WEIGHT KG / SET , , , CONVENIENT FOR CLENING SWINGS 90 OPENS CLER FROM CURTINS ND WINDOW FRME MX. VENTILTION CONCELED FITTINGS NODIZED LUMINIUM RILS VERTICLLY DJUSTBLE ± 1.5 MM B TOP FITTING BOTTOM FITTING FIRE-ESCPE OPENING: PLESE SEE 1 SET RIGHT HND 16/11

12 IP NO.s FITTING INSTRUCTIONS REHU NORDIC DESIGN PLUS: MRK ECCENTRIC PIN 16.5 FIG. 2 HORIZONTL PLN HINGE SIDE FITTING SHOWN ON FRME CILL RIGHT HND ILLUSTRTION IP NO MX. WEIGHT OF SSH KGS MIN. FRME WIDTH MM MX. FRME WIDTH MM USE SCREW NO FIG. 3 FIG. 1 VERTICL PLN REG. TLL ND NRROW WINDOWS: PLESE NOTICE THT ON TLL ND NRROW SSHES THE FLEXIBILITY OF THE MTERIL MY EFFECT HE MOVEMENT OF THE FITTING'S SLIDING ELEMENTS IN TOP ND BOTTOM. IT CN THEREFOR BE NECESSRY TO USE BOTH HNDS TO STBILIZE THE SSH WHEN OPENING THE WINDOW. THESE FITTINGS RE NOT SUITBLE FOR DOOR HEIGHT WINDOWS. MOUNTING: 1. THE FITTING SHOULD BE POSITIONED IN THE GROOVES T HED ND CILL OF FRME GINST THE SIDEFRME ND SCREWED ON (FIGURE 1 ND 2). FSTEN THE STOP RINGS THROUGH THE MIDDLE HOLE IN THE LU-RILS. 2. OPEN THE FITTING ND PUSH THE WINDOW SSH INTO POSITION BETWEEN THE 2 FITTINGS GINST THE NGLE ND FSTEN THE SCREWS. STRT WITH THE SCREW IN THE NGLE. 3. THE OPENING BETWEEN SSH ND FRME CN BE DJUSTED BY MENS OF THE ECCENTRIC PIN - USE TORX-20 KEY. ON THE PIN IS MRK THT ON DELIVERY IS IN NEUTRL POSITION. THE PIN CN BE TURNED 90 TO ETHER SIDE, WHICH GIVES N DJUSTMENT OF ±0.5 MM. MINTENNCE: THE FITTINGS RE NOT TO BE PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LUBRICTE THE PIVOT/MOVBLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LUBRICTE MINIMUM TWICE YER. DO NOT LUBRICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE

13 13 TOP SWING FITTING IP NO.s & IP NO ORDERING NO. IP NO. MTERIL STEEL WITHOUT SPECIFICTION SURFCE ELECTROPLTED STNDRD PCKING IN BOXES OF 1 SET MM B MM FRME DIMENSION OUTSIDE MM SCREWS PPROX. WEIGHT KG / SET ,5 & 4,0 1, ,5 & 4,0 1,44 B ,5 & 4,0 1, ,5 & 4,0 1,85 1/2 SET ,5 & 4,0 2, ,5 & 4,0 2, ,5 & 4,0 2, ,5 & 4,0 2, ,5 & 4,0 2,86 CONCELED FITTINGS DJUSTBLE FRICTION FULLY REVERSIBLE OPENS CLER OF CURTINS ND WINDOW FRMES NODIZED RILS FIRE-ESCPE OPENING: PLESE SEE ORDERING NO. MTERIL SURFCE IP NO. STEEL LEFT ELECTROPLTED STNDRD PCKING IN BOXES OF 20 PCS. MM SCREW PPROX. WEIGHT KG / PC. RISTRICTOR IP NO ,5 4,0 0,05 16/11

14 14 IP NO.s & IP No FITTING MCHINING INSTRUCTIONS REHU NORDIC DESIGN PLUS: CUT OUT IN SIDE FRME IN FULL LENGTH R5 7 TOP FRME DEPTH 3 MM FIG. 1 REMOVE THE INNER NOSE PLUS THE SMLL REIN- FORCEMENT ON THE OUTER NOSE IN FULL LENGTH OF SIDE SSH FIG TOP CORNER OF SIDE FRME Ø DEPTH 6 MM 10 HOLE IN UPPER FRME (FOR SWING ELEMENT) SEE FIG. 2 SEE FIG. 3 Ø14 X 10 DEPTH 3 MM R5 FIG. 2 FIG. 4 PROFILE ND CUT OUTS: IT IS NECESSRY TO CUT WY MTERIL IN SSH S WELL S FRME FROFILE BEFORE MOUNTING THE REVERSIBLE PROJECTING GER. LSO IT IS NECESRY TO MKE THE SSH 2 MM LESS WIDER THN FOR OTHER WINDOW TYPES. SSH: 1. SSH MUST BE MNUFCTURED SO THT THERE IS ONE MM EXTR SPCE BETWEEN SIDE FRME ND SIDE SSH COMPRED TO OTHER WINDOWS. 2. ON THE SIDE SSH THE INNER NOSE PLUS THE SMLL REINFORCEMENT ON THE OUTER NOSE HS TO BE REMOVED IN FULL LENGTH OF THE SIDE SSH. FRME: 1. THE SIDE FRME IS MDE WITH THROUGH GOING GROOVE (12 X 7 MM) PLCED 20 MM FROM FRONT EDGE OF FRME, SEE FIG. 1 ND 2. IMPORTNT: GROOVE MUST BE MDE CCORDING TO THESE SPECI- FICTIONS. EXTR TTENTION MUST BE PID TO THE GROOVES WHEN WELDING THE FRME CORNERS TOGETHER. MKE SURE THT THE PROFILE ND THE GROOVE KEEP ITS FORM, S DEFORMED PROFILE WILL CUSE PROBLEMS FOR THE RESTRICTORS ND FOR THE OPERTING OF THE GER. 2. HOLE FOR THE SWING ELEMENT HS TO BE MDE IN THE UPPER FRME, SEE FIG CUT OUT FOR THE BERING PLTE IN THE TOP CORNER OF THE FRME HS TO BE MDE, S SHOWN IN FIG. 2, 3 ND 4. FITTING INSTRUCTIONS - SEE NEXT PGE

15 REHU NORDIC DESIGN PLUS: IP NO.s & IP No FITTING INSTRUCTIONS TORX20 FIG FIG. 3 FITTING INSTRUCTIONS: 1. SHORTEN THE LU-RIL TO FIT THE HEIGHT OF THE INNER FRME. PLCE FITTING INTO BOTH SIDES OF THE FRME ND GINST TOP FRME ND FSTEN THE SCREWS. 2. PLCE THE BERING PLTE IN THE CUT-OUT IN TOP CORNER OF FRME ND FSTEN. THE BERING PLTE MUST BE LEVEL WITH TOP FRME ND LEVEL WITH THE SIDE FRME IN THE LOWER PRT OF THE BERING PLTE. 3. INSERT THE SSH BETWEEN HINGE RMS ND PUSH THE SSH GINST THE STOP BRCKET. FSTEN THE SSH STRTING WITH THE SCREWS IN THE STOP BRCKET. OBS: IT IS IMPORTNT THT THE STOP BRCKET IS CENTERED IN THE GROOVE. THE HINGE RMS MUST BE RESTING GINST THE SIDES OF THE GROOVE IN THE FULL LENGTH OF THE GROOVE, LSO BY THE SWING ELEMENT IN THE TOP. 4. THE SSH CN BE OPENED TO NY NGLE. FOR KEEPING IT OPEN T LRGE OPENING NGLE LIGHT FRICTION CN BE OBTINED BY MENS OF THE FRICTION SCREWS IN THE SIDES. THE FRICTION HS TO BE THE SME ON BOTH SIDES. PLESE NOTE THT THE SSH IS NOT SECURED FOR HEVY WINDS ND OTHER HEVY INFLUENCE. 5. THE SSH CN BE DJUSTED VERTICLLY ±0.75 MM BY MENS OF THE SCREW IN THE BERING PLTE (USE TORX 20), SEE TOP OF FIG. 1. MKE SURE THT THE SSH IS CENTERED IN THE FRME. 6. MKE SURE THT THE SWING ELEMENT CN MOVE FREELY INTO THE UPPER FRME, WHEN THE WINDOW IS CLOSED. 7. FIT THE RESTRICTOR IP NO ON THE LEFT SIDE, SEE FIG. 1. PLESE CHECK RESTRICTED OPENING POSITION S WELL S CLENING POSITION. 8. IN CLENING POSITION THE TOP NOTCH SHOULD LWYS BE USED, SEE BOTTOM OF FIG 1. BOTTOM NOTCH IS FOR RESTRICTED OPENING POSITION ONLY. OPERTION INSTRUCTIONS: 1. OPEN THE WINDOW - THE RESTRICTOR WILL UTOMTICLLY RESTRICT THE WINDOW. 2. PULL THE SSH 20 MM - THE RESTRICTOR IS RELESED BY PULLING IN ON THE LITTLE FINGER IN THE BOTTOM OF THE RESTRICTOR (SEE BOTTOM OF FIG. 1). OPEN THE WINDOW. 3. WHEN THE WINDOW IS REVERSED FOR CLENING, THE RESTRICTOR WILL LOCK UTOMTICLLY. DISENGGE S MENTIONED IN POINT 2. FITTING ON FRME FIG. 1 IP N0. FINGER FITTING LENGTH MM IP NO MX. WEIGHT KGS USE THE LRGEST POSSIBLE FITTING MINTENNCE: THE FITTINGS RE NOT TO BE PINTED. WHEN FITTING - LUBRICTE THE PIVOT/ MOVBLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HERFTER LIBRICTE MINIMUM TWICE YER. DO NOT GRESE THE LUMINIUM RILS. TEST THE OPERTION FROM TIME TO TIME. SEE LSO INSTRUCTIONS ON PGE

16 16 FITTING INSTRUCTIONS

17 DJUSTBLE CNOPY STY WITH FRICTION IP NO.s & ORDERING NO. IP NO. MTERIL STEEL WITHOUT SPECIFICTION SURFCE ELECTROPLTED INDUSTRY PCKING IN BOXES OF 25 SETS MM B MM SCREW PPROX WEIGHT KG / SET B ,0 0, ,0 0, ,0 1,00 1/2 SET VERTICLLY DJUSTBLE ± 1.5 MM CONCELED FITTINGS DJUSTBLE FRICTION NODIZED LUMINIUM RILS FRICTION IN LL POSITIONS FIRE-ESCPE OPENING: PLESE SEE

18 IP NO.s & FITTING INSTRUCTIONS REHU NORDIC DESIGN PLUS: FIG IP NO MX. SSH WEIGHT KG MX. FRME HEIGHT MM USE SCREW NO FIG. 2 OBS! RE. IP NO FOR BIG WINDOWS (>1200 MM) WITH 3-LYER GLSS ND NO REQUIREMENTS FOR EGRESS OPENINGS THE USE OF IP NO IS RECOMMENDED, S THE VENTILTION POSITION OTHERWISE MY BE DIFFICULT TO CHIEVE BECUSE OF THE OPENING GEOMETRY OF THE GERS. FITTING: 1. CLOSE THE FITTING ND PLCE IT IN THE GROOVE OF THE SIDE FRME. PLCE THE FITTING GINST THE TOP FRME. PLCE ND FSTEN THE SCREW IN THE BOTTOM HOLE OF THE FITTING. OPEN THE FITTING ND FSTEN THE REMINING SCREWS. FOR IP NO FSTEN THE STOP THROUGH THE TOP SCREW HOLE. 2. PUSH THE SSH INTO ITS PLCE BY INSERTING IT BETWEEN THE FITTINGS, GUIDED BY THE GROOVES IN THE SSH, TILL THE SSH HITS THE STOPS OF THE FITTING. FSTEN THE FITTING STRTING WITH THE CREW IN THE STOP BRCKET : FSTEN THE STOP PLTE THROUGH THE UPPER SCREW HOLE IN THE STOP PLTE ND THROUGH THE UPPER SCREW HOLE IN THE LURIL. THIS ENBLES MX. FIRE ESCPE OPENING. USE LOWER SCREW HOLE IN STOP PLTE TO CHIEVE MX,. SSH LOD OF 60 KGS. IF LOWER SCREW HOLE IS USED THE FIRE ESCPE OPENING WILL BE REDUCED : LWYS USE THE UPPER SCREW HOLE IN THE LURIL FOR MOUNTING THE STOP PLTE. USE THE UPPER SCREW HOLE IN STOP PLTE FOR MX. FIRE ESCPE OPENING. USE THE MIDDLE SCREW HOLE IN THE STOP PLTE TO CHIEVE MX. SSH LOD OF 85 KGS. USE THE LOWER SCREW HOLE IN THE STOP PLTE TO CHIEVE MX. SSH LOD OF 100 KGS. IF MIDDLE OR LOWER SCREW HOLES IN STOP PLTE RE USED THE FIRE ESCPE OPENING WILL BE REDUCED. 3. NOW THE FRICTION MY BE DJUSTED BY MENS OF THE SCREWS IN THE SLIDES. THE BEST RESULT FOR THE WINDOW MOVEMENT IS CHIEVED BY EQUL FRICTION T EITHER SIDE. 4. THE SSH CN BE DJUSTED ±1.5 MM UP OR DOWN. BEFORE NY DJUSTMENT THE MOUNTING SCREWS IN THE BOTTOM IN ECH SIDE OF THE FRME HVE TO BE LOOSENED. THEN DJUST BY USING TORX-20 KEY TO TURN THE ECCENTRIC PIN. BY DELIVERY THE MRK ON THE ECCENTRIC PIN IS IN VERTICL PERSITION INDICTING THE 0-POSITION. WHEN THE MRK IS IN HORIZONTL POSTION IN EITHER TOP OR BOTTOM, THE FITTING IS DJUSTED TO IT S MX OF ±1.5 MM. FTER THE DJUSTMENT THE MOUNTINGSCREWS IN THE BOTTOM OF ECH SIDE RE FSTENED. ECCENTRIC PIN MRK FIG. 3 MINTENNCE: THE FITTINGS RE NOT TO BE PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LUBRICTE THE PIVOT/MOVBLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LUBRICTE MINIMUM TWICE YER. DO NOT LUBRICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE /11

19 DJUSTBLE CNOPY STY WITH DJUSTBLE FRICTION IP NO ORDERING NO. MTERIL SURFCE B IP NO. STEEL W/O SPECIFICTION ELECTROPLTED INDUSTRYPCKING IN BOXES OF 25 SETS ,0 0,70 MM B MM SCREW PPROX. WEIGHT KG / SET 1/2 SET VERTICLLY DJUSTBLE ± 1.5 MM DJUSTBLE FRICTION CONCELED FITTINGS NODIZED LUMINIUM RILS FIRE-ESCPE OPENING: PLESE SEE

20 IP No FITTING INSTRUCTIONS REHU NORDIC DESIGN PLUS: FIG FIG. 2 IP NO MX. SSH WEIGHT KG 70 MX. FRME HEIGHT MM 1400 SCREW 4.0 FITTING: 1. CLOSE THE FITTING ND PLCE IT IN THE GROOVE OF THE SIDE FRME. PLCE THE FITTING GINST THE TOP FRME. PLCE ND FSTEN THE SCREW IN THE BOTTOM HOLE ND THE HOLE IN THE SIDE PRT OF THE LURIL. OPEN THE FITTING ND FSTEN THE REMINING SCREWS. 2 PUSH THE SSH INTO ITS PLCE BY INSERTING IT BETWEEN THE FITTINGS, GUIDED BY THE GROOVES IN THE SSH, TILL THE SSH HITS THE STOPS OF THE FITTING. FSTEN THE FITTING STRTING WITH THE SCREW IN THE STOP BRCKET. FINLLY FSTEN THE STOP IN THE LURIL. 3. NOW THE FRICTION MY BE DJUSTED BY MENS OF THE SCREWS IN THE SLIDES. WHEN DJUSTING MKE IS SO, THT THE TOP GLIDER MOVES FIRST DOWN TO THE STOP. THE BEST RESULT FOR THE WINDOW MOVEMENT IS CHIEVED BY EQUL FRICTION T EITHER SIDE. ECCENTRIC PIN 4. THE SSH CN BE DJUSTED ±1.5 MM UP OR DOWN. BEFORE NY MRK DJUSTMENT THE MOUNTING SCREWS IN THE BOTTOM IN ECH SIDE OF THE FRME HVE TO BE LOOSENED. THEN DJUST BY USING TORX-20 KEY TO TURN THE ECCENTRIC PIN. BY DELIVERY THE MRK ON THE ECCENTRIC PIN IS IN VERTICL PERSITION INDICTING THE 0-POSITION. WHEN THE MRK IS IN HORIZONTL POSTION IN EITHER TOP OR BOTTOM, THE FITTING IS DJUSTED TO IT S MX OF ±1.5 MM. FTER THE DJUSTMENT THE MOUNTINGSCREWS IN THE BOTTOM OF ECH SIDE RE FSTENED. FIG. 3 MINTENNCE: THE FITTINGS RE NOT TO BE PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LUBRICTE THE PIVOT/MOVBLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LUBRICTE MINIMUM TWICE YER. DO NOT LUBRICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE

21 21 SFETY CTCH IP NO ORDERING NO. MTERIL SURFCE IP NO. STEEL LEFT RIGHT ELECTROPLTED STNDRDPCKING IN BOXES OF 5 SETS MM SCREW PPROX. WEIGHT KG / SET 1 SET RIGHT ,0 0,06

22 22 IP No FITTING INSTRUCTIONS REHU NORDIC DESIGN PLUS: MRK X SSH X BOTTOM FRME SIDE FRME FIG. 1 RIGHT HND ILLUSTRTION FIG. 2 THE FITTING CN BE USED ON BOTH TOPHUNG/TOPGUIDED S WELL S SIDEHUNG/SIDEGUIDED WINDOWS. ON TOPHUNG/TOPGUIDED WINDOWS THE RESTRICTOR IS PLCED IN THE BOTTOM OF THE SIDE FRME ND THE RECEIVER IS PLCED IN THE BOTTOM OF THE SIDE SSH. ON THE SIDEHUNG/SIDEGUIDED WINDOWS THE RESTRICTOR IS PLCED IN TOP/BOTTOM FRME ON THE OPPOSITE SIDE OF THE HINGES ND THE RECEIVER IS PLCED IN THE TOP/BOTTOM SSH OPPOSITE THE HINGES. X-DIMENSION IS OPTIONL. BY USING LRGER X-DIMENSION THE VENTILTION OPENING WILL BE EXTENDED. IMPORTNT: THE RECEIVER MUST BE MOUNTED SO THT IT HITS THE MRK ON THE RESTRICTOR RM WHEN THE WINDOW IS CLOSED. SEE FIG. 1 OPERTING INSTRUCTIONS: 1. OPEN THE WINDOW UNTIL THE RESTRICTOR ENGGES. 2 PULL THE SSH PPROXIMTELY 20 MM BCKWRDS. 3. PRESS THE RESTRICTOR IN THE DIRECTION OF THE RROW S YOU OPEN THE WINDOW. 4. WHEN THE WINDOW IS CLOSED THE RESTRICTOR RE-ENGGES UTOMTICLLY. USE SCREW NO. 4.0 MINTENNCE: THE FITTINGS RE NOT TO BE PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LUBRICTE THE PIVOT/MOVBLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LUBRICTE MINIMUM TWICE YER. DO NOT LUBRICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE

23 4,5 23 FRICTION STY for windows IP NO ORDERING NO. MTERIL SURFCE B IP NO. STEEL LEFT RIGHT ELECTROPLTED STNDRD PCKING IN BOXES OF 25 PCS. MM B MM MTERIL MM SCREW PPROX. WEIGHT KG / PC X3 4,0 0,15 CONCELED FITTING OPENS UP TILL 100 FRICTION IN LL POSITIONS DJUSTBLE FRICTION NODIZED LUMINIUM RIL IP NO FITTING INSTRUCTIONS REHU NORDIC DESIGN PLUS: 11,8 2,2 135 DJUSTBLE FRICTION FIG. 1 FIG USE SCREW NO. 4.0 MINTENNCE: THE FITTING RE NOT TO BE PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN MOUNTING - LUBRICTE THE PIVOT/MOVBLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HERFTER LUBRICTE MINIMUM TWICE YER. DO NOT LUBRICTE THE LUMINIUM RIL. SEE LSO INSTRUCTIONS ON PGE FIG. 3

24 4,5 24 FRICTION STY for doors IP NO ORDERING NO. MTERIL SURFCE IP NO. STEEL LEFT RIGHT ELECTROPLTED STNDRD PCKING IN BOXES OF 10 PCS. MM B MM MTERIL MM SCREW PPROX. WEIGHT KG / PCS. B X3 4,0 0,24 CONCELED FITTING OPENS UP TILL 100 FRICTION IN LL POSITIONS DJUSTBLE FRICTION NODIZED LUMINIUM RIL IP NO FITTING INSTRUCTIONS REHU NORDIC DESIGN PLUS: ,8 2,2 DJUSTBLE FRICTION FIG. 1 FIG USE SCREW NO. 4.0 MINTENNCE: THE FITTING RE NOT TO BE PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN MOUNTING - LUBRICTE THE PIVOT/MOVBLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HERFTER LUBRICTE MINIMUM TWICE YER. DO NOT LUBRICTE THE LUMINIUM RIL. SEE LSO INSTRUCTIONS ON PGE FIG. 3

25 25 CCESSORIES IP NO.s & ORDERING NO. IP NO. MTERIL LUMINIUM PLSTIC WITHOUT SPECIFICTION SURFCE NODIZED WHITE STNDRD PCKING IN BOXES OF 20 PIECES STNDRD PCKING IN BOXES OF 25 PIECES MM B MM C MM SCREW PPROX. WEIGHT KG / PIECES ,4 19,8 4,0 0, , ,0 0,01 C B SUPPORT FITTING IP NO C B GUIDE BLOCK IP NO

26 26 CSEMENT HOOKS & FITTING CSEMENT INSTRUCTIONS FSTENERS ORDERING NO. MTERIL SURFCE B B IP NO. ZINK LLOY W/O SPECIFICTION ELECTROPLTED / WHITE ELECTROPLTED ELECTROPLTED YELLOW STNDRD PCKING IN BOXES OF 50 PIECES INDUSTRY PCKING IN BOXES OF 250 PIECES MM B MM HOLE FOR PIN MM PPROX. WEIGHT KG / 100 PIECES , , TTENTION: IP NO IN POWDER PINTED VERSIONS CN ONLY BE USED TOGETHER WITH IP NO B MTERIL ORDERING NO. SURFCE IP NO. STEEL W/O SPECIFICTION ELECTROPLTED / WHITE ELECTROPLTED ELECTROPLTED YELLOW STNDRD PCKING IN BOXES OF 50 PIECES INDUSTRY PCKING IN BOXES OF 250 PIECES INDUSTRY PCKING IN BOXES OF 500 PIECES MM B MM PIN MM SCREW PPROX. WEIGHT KG / 100 PIECES B ,3 34 5,6 3,5 0, ,5 5,

27 27 FITTING INSTRUCTIONS IP NO DRILL 5 MM HOLE FOR RING SCREW SSH 3,5 FRME , FIG. 1 IP NO FIG. 2 IP NO WITH FIG. 3 IP NO WITH IP NO SSH FRME FRME ,5 SSH SSH FRME FITTING: 1. MOUNT THE RECEIVER 1 IN THE WNTED HEIGHT ON THE SIDEFRME. 2. FOR CSEMENT FSTENERS WITH SCREW PLTE 2 MESURE PRECISELY ON THE SSH ND PRE-DRILL FOR THE RING SCREW. MRK UP THE 2 SCREW HOLES ON THE SCREW PLTE ND FSTEN THE CSEMENT FSTENER. 17/05

28 28 MINTENNCE FITTING LUBRICTION INSTRUCTIONS GENERLLY all parts of a building have to be looked after and maintained from time to time. This of course also applies for fi ttings in windows and doors. How often fi ttings in windows and doors should be maintained depends to a large extent on how they are used, how often they are operated, and not least on the environment the fi ttings are exposed to. Corrosion may also be caused by other factors, such as corrosive liquids, air pollution etc. Special attention should be given to fi ttings used in windows and doors in urban and industrial areas or other areas with a high traffi c intensity as well as coastal areas. Fittings in such environments should be checked and greased more often than fi ttings used in areas with less corrosive effects. HINGES ND FITTINGS should be lubricated when necessary, or at the minimum twice a year. SLIDING ELEMENTS S WELL S LL LURILS with sliding surfaces are to be kept clean and free from dust and dirt to ensure a smooth sliding function. Stearin wax or a clean lubricating fi lm (but no oil and no grease!) can be applied onto the alluminium rails. ESPGNOLETTES ND OTHER LOCKING FITTINGS should be greased or lubricated with acid free grease or acid free oil on spray. The grease/oil should be applied into the mechanism box as well as on the joints of the side bolts, the roller bolts, or the mushroom head bolts while activating the mechanism repeatedly. Grease or lubricate when necessary or at the minimum twice a year. Continues...

29 29 MINTENNCE LUBRICTION INSTRUCTIONS BRSS will sooner or later get some discoloration in a brownish tone depending on the environment in which it is placed. The original brass surface can be maintained by polishing from time to time. STINLESS STEEL can get some discoloration, although this rarely happens. Different chemical infl uences like acid fumes, contamination from wood preservation treatments, or air pollution may cause discoloration of the metal, sometimes to a reddish tone which could look like rust. Thin discoloration can be removed just by using common cleaner or polish. PINTED FITTINGS will from time to time need repainting. Before painting all parts should be cleaned carefully. When choosing type of paint and when applying the paint remember to follow the instructions from the paint manufacturer very carefully. When painting a wooden window in a house, it is a good idea also to paint the visible parts of the fi ttings (please note: No alurails nor sliding parts should ever be painted!). The painting of the fi tting will minimize corrosion and add to the lifetime of the fi tting. lways make sure that the proper function of a fi tting is not affected by the painting. NODIZED LUMINIUM should be cleaned from time to time, depending on the surroundings in which it is placed. Cleaning of the surface with a cloth or sponge is recommended. Eventually a neutral solvent can be used. Emery cloth, steel wool, sodium carbonate, and other cleansers or abrasives containing alkalies or acid should never be used. ON THE WINDOW ND DOOR FCTORY SITE all fittings should be lubricated or greased before shipment. Hinges should be lubricated with acidfree oil while activating repeatedly, an acidfree grease can also be used. When using grease it should be applied directly onto the pin of the hinges. It may be necessary to dismantle the sash before greasing. Especially hinges with a brass pin should be greased. When mounting fi ttings, please make sure that the tools do not damage the original surface treatment. When original surface has been damaged make sure that remedial take place as soon as possible. WHEN IN DOUBT PLESE CONTCT YOUR LOCL SUPPLIER OR /S J. PETERSENS BESLGFBRIK.

30 30 FITTING NOTES INSTRUCTIONS

31

32 /S J. PETERSENS BESLGFBRIK JCOB PETERSENSVEJ 9, DK-9240 NIBE TEL.: (+45) ttings.com