EURO (3876) Euro-C2 Installation Instructions Euro-Wall Systems, LLC

Transcription

1 EURO (3876) Euro-C2 Installation Instructions

2 Installation Instructions Euro-C2 step A.1) Assemble Bottom corner Pre-caution: it is recommended to use screw wax to prevent screw from snapping. 3 / #10 x 2 (Square PH) sill to Gasket Note that track insert is in place prior to screwing sill to the jamb. sill NOTE: When joining two header tracks together do not butt joint - MUST be a 45 degree miter cut. When joining two sill tracks together do NOT butt joint - MUST be a 45 degree miter cut. step A.2) Assemble top corner 3 / #10 x 2 (Square PH) Do not use this screw chase NOTE: Pre-caution: it is recommended it is recommended to use screw to use wax screw to prevent wax to prevent screw from screw snapping from snapping 2

3 step A.3) Apply Horizontal Frame weather seal Header Slide Pile-Fin Weather Seal (non-adhesive) into the slot. Cut weather-strip ends at 90 degrees. Tip: In order to insert Weather Seal smoothly, apply paraffin wax in Weather Seal grooves. NOTE: When joining two header tracks together do NOT butt joint - MUST be a 45 degree miter cut. When joining two sill tracks together do NOT butt joint - MUST be a 45 degree miter cut. step A.4) Apply vertical Frame weather seal Header Cut vertical Weather Seal ends at 45 degree angle to match horizontal weather-stripping. Apply minimal amount of clear silicone between 45 degree angled cut ends and horizontal Weather Seal. r Sill liner to be installed after inspection sill C2 Enhanced and C2 Storm apply Weather Seal on frame. 3

4 step A.4) Jobsite Preparation considerations Rough opening 1. Ensure correct rough opening specifications: a) A) Measure according to signed Euro-Wall Eclipse Architectural shop drawing shop drawing b) B) Plumb opening c) C) Level opening d) D) Square Square opening opening 2. Make sure the frame header is designed to withstand the dead loads of all Panels including glass plus momentum and impact 2. Make sure the frame header is designed to withstand the dead loads of all Panels including glass plus momentum and impact loading since it is top-hung Panel system. Rough opening header must not deflect more than 1/16 (2 mm) when carrying the loading since it is a top-hung Panel system. Rough opening header must not deflect more than 1/16 (2 mm) when carrying the weight of the Panels according to hardware suppliers specifications. weight of the Panels according to hardware suppliers specifications. 3. Ensure the head of the Folding Panel system can be securely fastened to the header components of existing structural header 3. Ensure the head of the Folding Panel system can be securely fastened to the header components of existing structural header beam. beam. 4. Recommended wood framing for opening or a continuous plane of structural wood to maintain stability, ease of fastening and 4. securing. Recommended wood framing for opening or a continuous plane of structural wood to maintain stability, ease of fastening and 5. Each securing. panel can weigh up to a maximum of 176 lbs (80 kg). Weigh one Panel or consult quote to determine total weight of 5. Folding Each panel Panel can system weigh or up contact to a maximum Eclipse Architectural of 200 lbs (100 for kg). the Weigh weight one of each Panel Panel. or consult quote to determine total weight of Folding Panel system or contact Euro-Wall for the weight of each Panel. step A.5) Frame placement into Rough opening Detail c: Header Detail A: sill Detail B: Detail a: sill Euro-C2 Storm Extra installation screw hole 1. Ensure sill is plumb and level 2. Sill sag to be no more than 1/6 *(2mm) at centre span 3. Sill bow to be avoided at any location of the sill 4. Anchoring screws are supplied by Eclipse Euro-Wall Architectural 5. Envelope details are not included in this guide. Please consult with your local building codes. 6. In order to reach enhanced performance (>DP70), (>DP60), use extra screw line located in the shootbolt channel as per images for head / jamb / sill. 7. Seal off all installation screw holes in frame with silicone. NOTE: All sills and headers must be joined by a miter cut. 4

5 Detail B: Euro-C2 extra installation screw hole 1. To accommodate for the wall pivot cup, it is recommended to pre-drill a 11/16 (17mm) diameter hole in the rough opening due to to the protruding wall wall cups (1/2 ( ½ or or 12mm). 2. Bow of the jamb to be kept to a minimum of 1/8 (3mm). 3. Anchoring It is recommended screws are to supplied use a continuous by DS group board (as alternate apply pieces) that will act as a 4. It back-up is recommended in the hollow to use jamb. a continuous board (as alternate apply pieces) that will act as a back-up in the hollow jamb. 4. Seal off backside of the middle pivot cup(s) with silicone. 5. Seal off backside of middle pivot cup(s) with silicone Detail c: Header Euro-C2 extra installation screw hole 1. The screw supplied used 3 must (75mm) penetrate PH track at screw least 1 is 1/2 a suggested (38mm) into screw the size rough only. opening The final structural header screw used beam must that penetrate is to carry at the least accumulative 1 ½ (38mm) Panel into load. the rough The size opening of the structural bolt head should header not beam interfere that is with to carry any the carrier accumulative wheels. Panel load. The size of the bolt 2. The head material should used not interfere for insulating with any the carrier shim space wheels. should be non-expandable material. 2. The material used for insulating the shim space should be non-expandable 3. Avoid the head from sagging after panels are installed and after full roof load is in place. material. We recommend installing the header with a slight bow (crown), but not more than 1/8 3. Avoid the head from sagging after panels are installed and after full roof load is (3mm) over the full system length. in place. We recommend installing the header with a slight bow (crown), but not 4. For Florida product approved installations see fastener details in FL#15472R-1 Guide. more than 1/8 (3mm) over the full system length. 4. Anchoring screws are supplied by Eclipse Architectural. step A.6) loading the Head track Header 1. Before installing the carriers, ensure that the track is clear of all debris and there is no contamination of metal parts that could restrict Panel movement or damage wheels. 2. Use a clean cloth to lubricate the track and the wheels with a small quantity of white petroleum jelly (Vaseline). not provided by 3. Consult Eclipse Architectural. the shop drawings and load sequentially to applicable configuration. 3. Consult the shop drawings and load sequentially to applicable configuration. 4. Load carrier sets through square hole in track. 4. Load carrier sets through square hole in track. 5

6 step A.7) Determine Panel sequence We suggest the panels are identified for the purpose of communicating sequence. Detail a step a.7.2 step a.7.1 step A.7.1.a) Bottom Pivot set Placement step A.7.1.b) Receive Panel onto Pivot Ensure when inserted in track, the hinge pin is located on the exterior as per image. Recessed stile 2 / #8 x 1-25mm (Phillips PH) Seal off fastener holes Black plastic sleeve can only go on one way sill Apply gasket under pivot. step A.7.2) Install cup for wall-pivot 1. Seal off holes for Pivot Cups with silicone. 2. Insert the hinge cap into the Bearing Tube first and then slide hinge pin down to engage into wall-pivot cup. Caution: Always support weight of Panel panels with flat/pry bar or similar tool when locating and securing any pivot or carrier vertical adjustment. 6

7 To ensure proper operation of Folding Panel System, insert the hinge while aligning the slot in the hinge flap with the rib on the Bearing Tube. step A.7.3) mounting the top wall Pivot Hinge to 1st Panel 4/ 8-32 x ¾ (Phillips FH) Important hinge consideration: Position all hinges in a way that one pushes the hinge up as per arrow. step A.8) Adjust Panel Height 13/64 (5 mm) Adjust clearance between top of the panel to bottom of the head track to 13/64" (5 mm) by using a flathead screw driver into the yellow shipping clip. Caution: Always support weight of Panel panels with flat/pry bar or similar tool when locating and securing any pivot or carrier vertical adjustment. Recessed stile 7

8 step A.9 Adjust Panel Reveal with Recessed stile sill 5/32 (4 mm) Adjust clearance between jamb and panel to 5/32 (4 mm) by using a long shafted Phillips screw driver as per image. Clearance dimension is measured when panel is in closed position. step A.10) Hanging 2nd Panel: mounting the top Intermediate carrier to 2nd Panel 6/ 8-32 x ¾ (Phillips FH) Adjust clearance between top of the panel to bottom of the head track to 13/64 (5 mm) by using a flathead screw driver into the yellow shipping clip. step A.11) Hanging 2nd Panel connecting 2nd Panel to 3rd Panel 6/ 8-32 x ¾ (Phillips FH) NOTE: Only weatherstrip every other door stile / panel 8

9 step A.12) Hanging 3rd Panel: mounting the top Intermediate carrier to 2nd Panel 3/ 8-32 x ¾ (Phillips FH) NOTE: Only weatherstrip every other door stile / panel step A.13) Hanging 4th Panel: Repeat steps A A.7.3 PHase III: Completion, Adjustments and Service Completion Check List 9 step 1: Ensure the multipoint is operating smoothly. (if applicable) 9 step 2: Ensure equal reveal to left and right of the system. 9 step 3: Ensure horizontal and vertical alignment. 9 step 4: Carrier pins at the top pivots, intermediate and end carriers are supplied with a yellow plastic shipping clip, which is installed to make the initial adjustment very easy. 9 step 5: Insert a flathead screwdriver into the slot to rotate the pin. 9 step 6: When the correct adjustment is reached and the Panels operate well, remove the shipping clip. 9 step 7: The blade will automatically snap into place once the blade and slot are aligned. 9 step 8: To readjust at a later date, simply pull the blade down to disengage it from the slot and rotate the pin. 9 step 9: Mount panel hold(s) to door at desired location/ direction with #8 32 x ¾ screws (9/64 tapped screw holes), keeping in mind the distance between the handle-set(s), alignment of Holds with one another and adjust the Hold to desired friction to open and close. 9

10 Folding Door Adjustments Carrier pins at the top pivots, intermediate and end carriers support the full door weight and it is here that the height of the panels is adjusted. Surelock ensures that once the heights are set, they stay set. using surelock : 1. Surelock is supplied with a yellow plastic shipping clip installed to make initial adjustment very easy. 2. Insert a flathead screwdriver into the slot to rotate the pin. 3. When correct adjustment is reached and doors operate well, remove the shipping clip 4. Surelock will automatically snap into place when the blade and slot are aligned. 5. To re-adjust at a later date, simply pull the blade down to disengage it from the slot and rotate the pin multipoint Door Adjustments All strike plates are adjustable to en sure smooth fine tuning, by using Phillips screw driver to loosen adjust screws, sliding the strike box to desired location and fasten the adjustments screws. adjustment screws (Phillips) Panel Handle Application Ensure slotted face of the spindle is facing down to receive the insert screw 10

11 Attention: Contractor Recommended Product care after Placement 1. Keep the plastic protection inserts on the sill at all times! Create a sturdy bridge to protect sill during construction phase. PHase. In In ad- dition, place a bridge while system is in open position and protect the side jambs of the Folding Door frame from damage. 2. Protect the Folding Door system from the following: Stucco: Causes etching on aluminum clogs the track and damages rollers. Drywall: clogs the system tracks; gums up rollers. Duct tape: Some adhesives chemically react with many finishes. Therefore use tape such as 3m painter s tape, but do not leave on any surface for more than 7 days. 3. Instructions for the owner and general contractor: Do not have small children operate or play within the confines of the Folding Panel system. Do not force the Folding Door system, contact Euro-Wall Eclipse Architectural if is found if to it be is found difficult to to be operate. difficult to operate. Apply protection bumpers if exterior handles contact the metal clad of the next Panel. Anchor Panel when in open position to prevent uncontrolled movement that might cause damage. operating of the Folding Door system: 1. Open system according to the following sequence: A. Multipoint release (if applicable) B. Release Twinpoint (s) C. Slide Panels to open position starting with Panel that does not have an Astragal (if applicable) 2. Close system according to the following sequence: A. Slide Panels to close position starting with Panel that has an Astragal (if applicable) B. Lock Twinpoint(s) C. Close swing-panel with multipoint (if applicable) 11

12 Attention: Consumer / End User Recommended Product care for End-user safety tips: Do not have small children operate or play within the confines of the Folding Door System. Anchor Panels when in open position to prevent uncontrolled movement that might cause damage. Do not force the Folding Door System. Have a qualified installer remove Panels or hardware when required. Contact Euro-Wall Eclipse Architectural if Panel is difficult Panel to is operate. difficult to ( ) operate. ( ) operating of the Folding Door system: Open system according to the following sequence: A. Multipoint release (if applicable) B. Release Twinpoint (s) C. Slide Panels to open position starting with Panel that does not have an Astragal (if applicable) Close system according to the following sequence: A. Slide Panels to close position starting with Panel that has an Astragal (if applicable) B. Lock Twinpoint(s) C. Close swing-panel with multipoint (if applicable) To close the Folding Door system, slide/fold the stack of Panels one by one (perpendicular to the track). If applicable, rotate the swing Panel to the closed position, only when all Panels are in their closed position. Consult Eclipse Euro-Wall Architectural Maintenance. Warranty Consult Care specific Guide. hardware Consult Folding specific Door hardware care and Folding maintenance Door care guide: and maintenance guide: Hinges: Wipe down the visible surfaces with warm soapy water on a soft cloth and then rinse off by wiping with a clean damp cloth. twinpoint: Spray suitable lubricant, such as, CRC Marine 66, Innox or WD40 to sliding pin and lock cylinder. Use plastic tube (supplied with lubricant) to direct spray. track and bearings: Apply, approximately 1/4 teaspoon (1 ml) of white petroleum jelly (Vaseline) or equivalent, to inner lip of each side of head track. Use clean cloth. Distribute lubricant evenly along track. Ensure wheels and bearings receive sufficient lubricant. Wipe all contaminant from track surfaces with damp cloth and mild detergent, clean surfaces with clean soft cloth. Apply thin film for systems installed in severe environments by wiping surfaces of track with anti-corrosive substance, such as, CRC Marine 66, Innox or WD40. Hangers, pivots and brackets: Spray thin film to hangers, pivots and brackets with anti-corrosive substance, such as, CRC Marine 66, Innox or WD40. Wipe exposed surfaces with clean soft cloth soaked in warm soapy water; rinse clean before applying corrosive preventative. Frequency Carry out care procedures with the following minimum recommendations: General environments every 6 months. Marine and industrial environments every 3 months. Regular maintenance is required for all hardware, even stainless steel, to keep manufacturer s warranty in place. 12