CABRIO Retractable Classic Roof / Double Rail System Step by Step Assembly Instructions

Size: px
Start display at page:

Download "CABRIO Retractable Classic Roof / Double Rail System Step by Step Assembly Instructions"

Transcription

1 CABRIO Retractable Classic Roof / Double Rail System Step by Step Assembly Instructions Before You Begin These installation instructions will lead you through the process of installing your new shelter. The installation of the shelter requires special attention to certain detail. Before you begin you should: CHECK YOUR ORDER. Make sure the contents of the carton match the product numbers on your order. Contact your dealer if there are any damaged, missing or incorrect parts. PAY ATTENTION TO SAFETY. Because of the size and weight of certain parts, installation is recommended with no fewer than two people. Always maintain a clean, organized work area. MAKE SURE YOU HAVE THE RIGHT TOOLS AND MATERIALS. Jardin de Ville supplies the appropriate fasteners upon request through your dealer for anchoring the shelter securely to the ground. If you are unsure about the required anchoring system best suited for your shelter, consult your dealer for the proper fastening method. REVIEW ENTIRE INSTALLATION GUIDE. This step gives you the opportunity to contact your dealer to answer any questions before you begin. Assembly Requirements Two Persons Hand Drill Ladder Wrench Kit Tape Measure Level Rubber Hammer Screwdriver Set Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

2 Assembly Overview Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

3 Part List (1 of 2) 2x B1 10 Side Beam (roof hinge side) 2x B2 4x P1 4x P2 12 or 14 Front Beam (transverse side) Triangular Corner Post Corner Post Cover 1x L1 Full Length Lever Arm 1x L2 Dummy Lever Arm 2xTF1 Transverse Roof Support with groove Cross-Sectional View 3xTF2 Transverse Roof Support (no groove) Cross-Sectional View 4xTS1 Lower Truss with 5/16 dia hole about pivot point 4xTS2 Middle Truss with 5/16 dia hole about pivot point 2xTS3 Center Truss with plastic spring slide and corner inserts TS1 TS2 TS3 TS2 2x R1 Flat Bar Roof Trusses TS1 1x R2 Lever Arm Strap KC01 1x KC02 4x LA3002 Post End Plate 16x 002 Plate Screw 1/4 x 1-3/4 1x KC.02L 1x KC.02R KC04 Roof Hinge (left) Roof Hinge (right) 4x PL102 Plastic Corner Beam Inserts 2x KC03 8x 025 Metal Screw #8-3/4 1x PL005 Roof Hinge Cover KC05 Inlcudes the following sub kits: 8x PL007 Plastic Corner Insert 1x SKC03-1 1x SKC03-2 1x SKC03-3 Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

4 Part List (2 of 2) 2x SKC03-1 KC06 2x 001 Tab Weld Nut 1/ x 003 Carriage Bolt - 5/16 x 2 2x 005 9/32 x 5/8 Flat Washer 16x 007 5/16 x 1-1/2 Flat Washer 2x 008 5/16 x 1/2 Lock Washer 16x 012 5/16 Nylon Lock Nut 2x 014 Hex Bolt - 1/4-20 x 5/8 KC07 2x 026 Roof Hinge Cover Screw #10-3/8 4x PL07 4x PL015 2x SKC03-2 4x PL016 4x PL014 2x 003 Carriage Bolt - 5/16 x 2 16x 002 Cover Screw - 1/4 x 1-3/4 6x 006 2x 009 5/16 x 3/4 Flat Washer 5/16 x 5/8 Lock Washer KC08 1x 002 Strap Screw - 1/4 x 1-3/4 2x 011 5/16 Nut 2x 018 1/4 dia Nylon Bushing 2x 019 Nylon Bushing - 5/16 1x 005 9/32 x 5/8 Flat Washer 2x SKC03-3 1x 010 Nylon Lock Nut - 1/4-20 5x 004 Hex Bolt - 5/16 x 3-1/4 2x PL011 Lever Arm Fork 10x 006 5/16 x 3/4 Flat Washer 1x PL012 Fork Installation Guide 5x 012 5/16 Nylon Lock Nut 2x 016 Self-Tapping Screw - #12 x 1-3/4 10x 019 Nylon Bushing - 5/16 2x PL010 1x PL013 KC31-SS 2x 020 Hinge Box Side Cover Plastic Finishing Hole Cap Lever End Cover 2x LT-A49 MISC 12x 040 Stainless Steel Secure Latch Self-Taping Screws #8-3/4" K.PL101 Pulleys included with curtains KC32-S 16x CAP.01 Plastic Caps K.APL001 Velcro Strips #8 Square Head Screwdriver Bit* #10 Square Head Screwdriver Bit* *Provided for European model only Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

5 Getting Started 1 Post end with holes P1 002 LA3002 Cross-Sectional View Secure the base plates [KC01.LA3002] to the bottom of each of the aluminum corner posts [P1] using metal bolts [KC01.002] as shown in the diagram. (Repeat step for all four corner posts.) Insert the bolts with a small angle towards the wall. LA KC.02L B Install the two roof hinges on the beams [B1] by first inserting two tab nuts [001] into the bottom interior groove of both beams. Then slide the tab nuts till the mid section of the beams. Install the roof hinges on both beams using tab nuts, bolts and washers from kit [SKC03-1] shown in the above right hand side diagram. LIGHTLY TIGHTEN BOLTS. The hinge will be centered and bolts will be tighten in step 6. 3 On a flat surface, assemble all the beams together by inserting the plastic corners [KC04.PL102] at each end. Once fully inserted, lock in place the plastic corners with supplied screws [KC04.025], as shown in view A-A. You may use pieces of the cardboard shipping box to protect the frame from scratches. View A-A B2 B1 025 PL102 B2 Cardboard B1 A-A Roof will open from this side Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

6 Assembling the Roof 4 Use a Rubber Hammer TF1 & TF2 PL007 Install the plastic corner inserts [KC05.PL007] at each end of the transverse roof supports [TF1] & [TF2] as shown in the figure above. You will need a rubber hammer to insert them properly. A-A View A-A Use a Rubber Hammer Middle Truss Assembly Complete the assembly by inserting the trusses [TS1], [TS2] and [TS3] at each end of the transverse roof supports as shown in the figure above. Again you will need a rubber hammer to insert them properly. 5 TS1 & TS2 Roof Truss Ends 019 Nylon Bushing On each end of the roof truss assemblies [TS1] & [TS2] install two plastic bushing [SKC ] as shown in the diagram. Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

7 Assembling the Roof Framework 6 TS1 TS2 TS3 TS2 TS1 B-B D-D C-C E-E Lay the trusses on top of the beam assembly in the order and orientation shown by the diagram above. Consult views B-B, C-C, D-D and E-E for specific detail. Then turn to the next page for a description on how to fix each trusses to the hinges. Install the middle plastic stub truss on the lower hole. The upper hole can be used in time if more pressure needs to be exerted by the middle truss onto the roof fabric. View B-B Holes used for Lever Arm and dummy Lever Arm (see Step 9) View C-C Holes used for Lever Arm and dummy Lever Arm (see Step 9) TF1 View D-D View E-E TF1 Transverse Support Groove Should be Facing Downwards Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

8 Assembling the Roof Framework Install the trusses on the hinge using hardware from kit [SKC03-2] shown in views B-B. Notice that only one side is shown. Repeat this step on the other hinge. Nylon bushing 019 KC.02L See Through View 012 View B-B (Hardware Installation) View B-B (TOP VIEW) 006 Center Hinge Assembly F-F F-F Once the trusses have been fixed properly to each hinge, center the roof assembly by allowing the protruding groove of [TF1] to extend just beyond the edge of beam [B2] (see view F-F). Then tighten the hinge bolts as shown in the bottom right diagram. Transverse Support Groove Facing Downwards View F-F 014 Tighten Bolts (repeat on other side) Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

9 Installing the Corner Posts 7 G-G Flat Washer 012 Lock-Nut View G-G (TOP VIEW) Attach one of the four corner posts [P1] to each corner of the structure using hardware from kit [KC06] shown in the top right diagrams. This step may require a second person or a ladder to lift the roof assembly in order to fix all four corner posts [P1]. See diagrams below for further assembly steps. P1 P1 P2 To complete the post assembly, snap together the corner posts [P1] and corner post covers [P2] using a rubber hammer as shown in the diagrams above. Repeat step for each corner. 002 KC07 Assembly Locking Key P2 Top View P2 Then fasten the top cover assembly [KC07] on top of each corner post [P1]. DO NOT OVER TIGHTEN SCREWS. The locking key can be in the unlocked position or removed from the cover assembly by turning then pulling it. Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

10 Archoring the Shelter 8 Make sure the structure is well aligned and levelled with the floor as shown in the diagram below. Consult the section below for recommendations on the type of anchorage required for fixing the structure on the floor. L W D C2 C3 level C1 Remaining holes in plate [LA3002] are used for fixing the structure on the floor See ANNEX 1 for measurements Dimensions given from center to center of plates [LA3002] Structure Anchorage System Recommendations OPTION A WOOD DECK/FLOOR OPTION B CONCRETE/CEMENT FLOOR Requirements: 8 (2 per plates) of each - 5/16" x 2" wood screws - 5/16" washers Requirements: 8 (2 per plates) of each - 3/8" x 1-1/2" expansion anchor * use 1/2" cement drill bit CONCRETE WOOD SOIL PAVER/GRASS This anchoring system is the recommended solution for anchoring your tent on other surfaces than wood or concrete such as paver or grass. Consult your dealer for more information on this fastening method. Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

11 Final Frame Assembly 9 I-I H-H PL012 TS2 PL011 Remove the guide after installing the fork. View H-H (step a) 016 View H-H (step b) Install the plastic fork [KC08.PL011] on the [TS2] truss assembly on the opening side. Locate the proper position of the fork by using the fork installation guide [KC08.PL012] as shown in views H-H. Then use the self tapping screw [KC08.016] to fix the fork on the transverse truss member. Then insert the end of the lever arm on the fork and fix the lever using hardware from kit [SKC03-2] shown in view I-I. Repeat step on other side for the dummy lever arm See Through View 003 PL011 KC.02L 10 View H-H (step c) PL005 L1 View I-I (TOP VIEW) L1 L1 To complete the roof hinge mechanism, install the plastic hinge cover [KC03.PL005] over the roof hinge using screws [SKC ]. Then install side cover [KC08.PL010] and the hole cap [KC08.020]. Repeat step on both side. PL Install the Plastic Finishing Cap Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

12 Final Frame Assembly Install the lever strap on the end of the lever arm using hardware from kit [KC08] shown in the left diagram. Then install the plastic cap [PL013] on the end of both the lever and PL013 R Roof Support TS1 040 B2 Center Line Locate the center distance of beam [B2].Then install the stainless steel latch [KC31.LT-A49] using the self-taping screws [KC31.040] on the roof support [TS1] and beam [B2]. Make sure the latch parts are fixed apart correctly such that it can be closed as shown in the adjacent diagram. Repeat step on other side. The stainless steel latch is used along with the corner locking mechanism (shown in step 7) to secure the roof truss in place. B2 LT-A49 Closed Latched 13 Insert velcro strips at every 16 in the top groove of the beams. Then fix the valance to the velcro strips [MISC K.APL001]. Start from one end of the valance and work your way around the frame assembly. See adjacent diagrams for detail. Inside view, facing B2 & TS1 TOP VIEW K.APL001 Velcro Strip (top groove) 16 apart Valance Velcro Strip (top groove) Roof will open from this side Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

13 Installing the Roof Fabric 14 J-J K-K L-L M-M Install the roof fabric cover over the frame assembly with roof trusses down. Make sure that all 4 corners of the roof fabric are aligned properly. SIDE VIEW View K-K Roof Fabric View J-J Weld Line View L-L Roof Support Velcro Strip The next step will give instructions on how to fix the roof cover to the frame assembly. Slide the flat bars [R1] in the pocket of the fabric as shown in View M-M.Then raise the truss assembly and push the flat bar and fabric into the groove of the transverse truss [TF1].Then fix the velcro strip around the 2 roof supports [TF2]. Note that the velcro should be fitted around the support as shown in views K-K (left hand side support) and L-L (right hand side support). Then raise the middle roof support [TF3] in its upright position and fix the velcro around it as shown in view J-J. TF1 View M-M (Step a) R1 Insert a flat bar on each end of the pocket View M-M (Step b) Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

14 Installing the Curtains 15 K.PL101 Plastic Pulley Snap Pulley in place Metallic Eyelet Curtain Exterior Side Curtain (Exterior Side) Zipper (Interior Side) Profile View CAP.01 Install plastic pulleys [MISC K.PL101] by snapping them in each metallic curtain eyelet. Use long nose pliers to facilitate this operation. Pulleys should be facing towards the curtain side on which the zipper is located (see above steps). Then install each curtain sections into the provided beam slots as shown by left hand diagram. After installing all pulleys, block the access with the caps [KC32-S.CAP.01] as shown in the diagram. Repeat step for each corner. See next step (16) for curtain installation example. 16 Roof Fabric & Valance Not Shown For Clarity outside rail inside rail curtains on inside rail TOP VIEW curtains on outside rail decorative curtains (installed using velcro strips on bottom beam groove) Velcro Strips Bottom Groove 16 apart The decorative curtains are installed using velcro strips [MISC K.APL001] inserted 16 apart in the bottom groove of the beams similarly to the valance in step 14. If you have purchased optional curtains (mesh netting, transparent plastic or acrylic fabric) install them on the inside or outside rail of the beams. Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

15 Installing the Curtains 17 Complete installation of each curtain sections at each corner. Installed curtains should resemble the above diagram. Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com of 15 Model # Cabrio 1.0

16 Annex 1 - Step 8 Measurements Dimensions given below are from center to center of plates [LA3002]. Internal Dimension 10x10 Model inches (cm) W 111 5/8 (283.5) L 111 5/8 (283.5) D 157 7/8 (401.0) C1 80 (203.2) C2 114 (289.6) C3 148 (375.9) Internal Dimension 10x12 Model inches (cm) W 111 5/8 (283.5) L 138 3/4 (352.4) D 178 1/8 (452.4) C1 80 (203.2) C2 114 (289.6) C3 148 (375.9) Internal Dimension 10x14 Model inches (cm) W 111 5/8 (283.5) L 161 3/8 (409.9) D 196 1/4 (498.5) C1 80 (203.2) C2 114 (289.6) C3 148 (375.9) Distributor: ShadeScapes Americas cuscini.shadescapesamericas.com Supp. of 15 Model # Cabrio 1.0

17 Architectural Testing TEST REPORT Report No.: C Rendered to: CUSCINI DESIGN, INC. Mirabel, Quebec CANADA PRODUCT TYPE: Fabric Covered Garden Pavilion with Convertible Roof SERIES/MODEL: Cabriolet Shelter Reference must be made to Report No. C , dated 08/31/12 for complete test specimen description and detailed test results.

18 Test Report No.: C Report Date: 08/31/12 Page 1 of Report Issued To: Cuscini Design, Inc Arthur-Sicard Mirabel, Quebec J7J 0E9 CANADA 2.0 Test Laboratory: Architectural Testing, Inc. 130 Derry Court York, Pennsylvania Project Summary: 3.1 Product Type: Fabric Covered Garden Pavilion with Convertible Roof 3.2 Series/Model: Cabriolet Shelter 3.3 Compliance Statement: Results obtained are tested values and were secured by using the designated test method(s). Test specimen description and results are reported herein. 3.4 Test Date: July 24, Test Record Retention End Date: All test records for this report will be retained until August 31, Test Location: Architectural Testing, Inc. test facility in York, Pennsylvania. 3.7 Test Sample Source: The test specimen was provided by the client. Representative samples of the test specimen(s) were not provided to Architectural Testing, Inc. from Cuscini Design, Inc. 3.8 Drawing Reference: The test specimen drawings have been reviewed by Architectural Testing and are representative of the test specimen(s) reported herein. Test specimen construction was verified by Architectural Testing per the drawings located in Appendix B. Any deviations are documented herein or on the drawings. 3.9 List of Official Observers: Name Company Jean Bourque Michel Bourque Paulo Medeiros Thomas Lawlor Michael D. Stremmel, P.E. Emily C. Riley Cuscini Design, Inc. Cuscini Design, Inc. Cuscini Design, Inc. Architectural Testing, Inc. Architectural Testing, Inc. Architectural Testing, Inc.

19 Test Report No.: C Report Date: 08/31/12 Page 2 of Test Procedure: The test specimen was subjected to a dynamic wind test. Winds were produced by an engine-driven fan located approximately 7 feet from the test specimen. The wind was directed to the front leading edge of the pavilion and subsequently at the corner of the pavilion (45 angle). Tests were conducted starting at 50 mph wind speed and increased in 10 mph increments without a relaxation period between wind speed increments. Each wind speed increment was maintained for thirty seconds. Wind speed increments continued until the maximum capacity of the equipment was reached. 5.0 Test Specimen Description: 5.1 Awning Size: 10' x 14' 5.2 Frame Construction: Frame Member Material Description Side beams (4) Aluminum Extruded Corner posts (4) Aluminum 6063 T6 Extruded, capped at bottom end using an aluminum base plate secured to the post with four 1/4" x 1-3/4" long Robertson flat head screws. Capped at top end using plastic cover assembly, secured using four 1/4" x 1-3/4" long Robertson flat head screws per post. Extruded aluminum cover plates were snap-fit to each post. Side beams Corner posts Joinery Type Square-cut N/A Detail Secured using plastic corner keys and two #8 x 3/4" long Robertson pan head screws per corner Secured to the beam corners using two 5/16" x 2" long carriage bolts, washers, and lock nuts 5.3 Roof Construction: Roof Member Material Description Transverse supports (2) Aluminum Extruded, constructed of three members each Trusses (3) 6063 T6 Extruded, constructed of three members each Transverse supports and trusses Joinery Type Mitered Detail Secured at corners with metal and covered in plastic keys and secured to hinges at each end using one 5/16" x 1-3/4" long hex bolt with washer, nylon bushing, and lock nut

20 Test Report No.: C Report Date: 08/31/12 Page 3 of Test Specimen Description: (Continued) 5.4 Curtain Assembly: Description Quantity Location Secured to groove in transverse Roof cover 1 supports and using Velcro straps around the transverse supports and trusses Curtains 4 Secured to roof beams using snap-fit plastic pulleys located at each metal eyelet in curtain 5.5 Hardware: Description Quantity Location Roof hinge 2 Secured to roof beam at midspan using two 1/4"-20 x 5/8" hex bolts, lock washers, flat washers, and tab washers per hinge Lever arm 1 Secured to center truss using a plastic fork and one #12 x 1-3/4" long selftapping Robertson flat head screw Lever strap 1 Secured to lever arm end using one 1/4" x 1-3/4" long Robertson flat head screw with nylon bushing, washer, and lock nut Plastic strap secured to transverse support at midspan using one 3/4" flat Plastic strap with locking head Tek screw. Plastic hooks secured 2 hooks to transverse support and roof beam using two #8 x 1-1/2" long self-tapping Robertson pan head screws each 6.0 Installation: The specimen was installed onto a concrete pad. Each frame leg was secured to the concrete using one 3/8" x 1-1/2" expansion anchor with bolt and nut.

21 Test Report No.: C Report Date: 08/31/12 Page 4 of Test Results: 7.1 Test #1: Pavilion curtains open Wind Speed Observations 50 mph No damage 60 mph No damage 70 mph No damage 80 mph No damage 90 mph No damage 100 mph Curtain pulled off pulleys at one corner 110 mph No additional damage 120 mph No additional damage 130 mph No additional damage Note: At the conclusion of the test, it was observed that the Velcro ties released along the truss furthest from the wind source and at the midspan of the center truss. 7.2 Test #2: Pavilion curtains closed Wind Speed Observations 50 mph No damage 60 mph No damage 70 mph Zipper broke on the font panels 80 mph No additional damage 90 mph No additional damage 100 mph No additional damage 110 mph No additional damage 120 mph No additional damage 130 mph Plastic strap released on the back side Note: At the conclusion of the test, it was observed that the Velcro ties released along the truss furthest from the wind source and at the midspan of the center truss.

22 Test Report No.: C Report Date: 08/31/12 Page 5 of 5 Architectural Testing will service this report for the entire test record retention period. Test records that are retained such as detailed drawings, datasheets, representative samples of test specimens, or other pertinent project documentation will be retained by Architectural Testing, Inc. for the entire test record retention period. This report does not constitute certification of this product nor an opinion or endorsement by this laboratory. It is the exclusive property of the client so named herein and relates only to the specimen(s) tested. This report may not be reproduced, except in full, without the written approval of Architectural Testing, Inc. For ARCHITECTURAL TESTING, Inc. Emily C. Riley Technician Michael D. Stremmel, P.E. Senior Project Engineer ECR:dem Attachments (pages): This report is complete only when all attachments listed are included. Appendix-A: Photographs (2) Appendix-B: Drawings (9) This report produced from controlled document template ATI 00479, issued 01/27/12.

23 Test Report No.: C Report Date: 08/31/12 Appendix A Photographs Photo No. 1 Test #1 Set-Up and Application of 50 mph Wind Load Photo No. 2 Test #2 Set-Up and Application of 50 mph Wind Load

24 Test Report No.: C Report Date: 08/31/12 Photo No. 3 Test #2 Application of 130 mph Wind Load

25 Test Report No.: C Report Date: 08/31/12 Appendix B Drawings

26

27

28

29

30

31

32

33

34

TERRACE / TERRACE CONCEPT Retractable Classic Roof / Double Rail System Step by Step Assembly Instructions

TERRACE / TERRACE CONCEPT Retractable Classic Roof / Double Rail System Step by Step Assembly Instructions TERRACE / TERRACE CONCEPT Retractable Classic Roof / Double Rail System Step by Step Assembly Instructions Before You Begin These installation instructions will lead you through the process of installing

More information

REVIEW ENTIRE INSTALLATION GUIDE. This step gives you the opportunity to contact your dealer to answer any questions before you begin.

REVIEW ENTIRE INSTALLATION GUIDE. This step gives you the opportunity to contact your dealer to answer any questions before you begin. Cabriolet Shelter (Retractable Roof) Step by Step Assembly Instructions Before You Begin These installation instructions will lead you through the process of installing your new shelter. The installation

More information

BARLOW TYRIE quality since Ref: x 3m - 12 x 10 Pavilion with Cabrio Folding Roof Step by Step Assembly Instructions

BARLOW TYRIE quality since Ref: x 3m - 12 x 10 Pavilion with Cabrio Folding Roof Step by Step Assembly Instructions Pavilions 3.66 x 4.5m - Step 12 x by 15 Step Pavilion Assembly Shelter Instructions with Double Rail Beams Ref: 9011215 3.66 x 3m - 12 x 10 Pavilion with Cabrio Folding Roof Step by Step Assembly Instructions

More information

ABRI Fixed Classic Roof / Single Rail System Step by Step Assembly Instructions

ABRI Fixed Classic Roof / Single Rail System Step by Step Assembly Instructions ABRI Fixed Classic Roof / Single Rail System Step by Step Assembly Instructions Before You Begin These installation instructions will lead you through the process of installing your new shelter. The installation

More information

Ref: x 3m - 12 x 10 Pavilion with Single Rail Beams Step by Step Assembly Instructions. Product Ref:

Ref: x 3m - 12 x 10 Pavilion with Single Rail Beams Step by Step Assembly Instructions. Product Ref: Pavilions 366 x 45m - Step 12 x by 15 Step Pavilion Assembly Shelter Instructions with Double Rail Beams Ref: 9011215 366 x 3m - 12 x 10 Pavilion with Single Rail Beams Step by Step Assembly Instructions

More information

TAS 201, TAS 202, TAS 203 and ASTM E330 PERFORMANCE TEST REPORT. Rendered to: DIAMOND DOOR PRODUCTS

TAS 201, TAS 202, TAS 203 and ASTM E330 PERFORMANCE TEST REPORT. Rendered to: DIAMOND DOOR PRODUCTS Architectural Testing TAS 201, TAS 202, TAS 203 and ASTM E330 PERFORMANCE TEST REPORT Rendered to: DIAMOND DOOR PRODUCTS SERIES/MODEL: Diamond GEM 130 MPH Series PRODUCT TYPE: Out-Swing Steel Entry Door

More information

Assembly Instructions

Assembly Instructions 18' W x 10' H or 12' H Peak Style Frame Assembly Assembly Instructions Before you start: 2+ individuals recommended for assembly, approximate time 3 hours. Recommended tools: Power Drill, Safety Glasses,

More information

ASTM E 1886 and ASTM E 1996 TEST REPORT. Rendered to: PRL ALUMINUM ARCHITECTURAL PRODUCTS City of Industry, California

ASTM E 1886 and ASTM E 1996 TEST REPORT. Rendered to: PRL ALUMINUM ARCHITECTURAL PRODUCTS City of Industry, California Architectural Testing ASTM E 1886 and ASTM E 1996 TEST REPORT Report No.: D1090.02-301-44 Rendered to: PRL ALUMINUM ARCHITECTURAL PRODUCTS City of Industry, California PRODUCT TYPE: Bi-Fold Door SERIES/MODEL:

More information

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED RAMPAGE P R O D U C T S 84 (+/- 1/4 ) INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO 1966-1977 TOOLS REQUIRED 3/8 WRENCH 7/16 WRENCH ½ WRENCH #2 PHILLIPS SCREWDRIVER 1/8 DRILL

More information

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

ASTM E1886 and ASTM E1996 TEST REPORT. Rendered to: FLEETWOOD WINDOWS AND DOORS Corona, California

ASTM E1886 and ASTM E1996 TEST REPORT. Rendered to: FLEETWOOD WINDOWS AND DOORS Corona, California This report contains in its entirety: Cover Page: 1 page Report Body: 11 pages Sketch: 1 page Drawings: 5 pages ASTM E1886 and ASTM E1996 TEST REPORT Report No.: E8384.02-301-18 Rendered to: FLEETWOOD

More information

ASTM E1886 and ASTM E1996 TEST REPORT. Rendered to: FLEETWOOD WINDOWS AND DOORS Corona, California

ASTM E1886 and ASTM E1996 TEST REPORT. Rendered to: FLEETWOOD WINDOWS AND DOORS Corona, California This report contains in its entirety: Cover Page: 1 page Report Body: 11 pages Sketch: 1 page Drawings: 12 pages ASTM E1886 and ASTM E1996 TEST REPORT Report No.: E8390.02-301-18 Rendered to: FLEETWOOD

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

ENTRY DOOR TEST REPORT. Rendered to: The Vistawall Group

ENTRY DOOR TEST REPORT. Rendered to: The Vistawall Group ENTRY DOOR TEST REPORT Rendered to: The Vistawall Group Product: Single 500 Wide Stile Outswing Full-Lite Aluminum Entry Door w/ Standard TH-43 Threshold and Woolpile Weathering Title Air Infiltration@

More information

This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently.

This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. Don t be put off by the size of the instruction manual as the large diagrams

More information

PERFORMANCE TEST REPORT. Rendered to: GLASSCRAFT DOOR COMPANY

PERFORMANCE TEST REPORT. Rendered to: GLASSCRAFT DOOR COMPANY PERFORMANCE TEST REPORT Rendered to: GLASSCRAFT DOOR COMPANY SERIES/MODEL: Buffalo Forge Steel Doors / Arch Top Double PRODUCT TYPE: In-swing Arch Top Double Door RH-4-5/8 Title Uniform Load Deflection

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

MIAMI-DADE COUNTY PERFORMANCE TEST REPORT. Rendered to: FLEETWOOD WINDOWS AND DOORS Corona, California

MIAMI-DADE COUNTY PERFORMANCE TEST REPORT. Rendered to: FLEETWOOD WINDOWS AND DOORS Corona, California MIAMI-DADE COUNTY PERFORMANCE TEST REPORT This report contains in its entirety: Cover Page: 1 page Report Body: 14 pages Sketch: 1 page Drawings: 5 pages Report No.: E8384.03-301-18 Rendered to: FLEETWOOD

More information

ASTM E 283, ASTM E 547, AND ASTM E 330 TEST REPORT. Rendered to: SIMPSON DOOR COMPANY

ASTM E 283, ASTM E 547, AND ASTM E 330 TEST REPORT. Rendered to: SIMPSON DOOR COMPANY ASTM E 283, ASTM E 547, AND TEST REPORT Rendered to: SIMPSON DOOR COMPANY SERIES/MODEL: Simpson Door Fir 1501 PRODUCT TYPE: Wood Inswing Door with Side Lites Report No: Test Date: 04/02/04 Report Date:

More information

CABANA / PAVILION ASSEMBLY ALUMINUM FRAME MODELS

CABANA / PAVILION ASSEMBLY ALUMINUM FRAME MODELS Assembled cabanas are large & heavy. Assemble at place of use. CABANA / PAVILION ASSEMBLY ALUMINUM FRAME MODELS Step 1 CAUTION: To avoid damage to the finish of your Cabana frame, prepare a smooth, non-scratch

More information

Horizontal Cable Systems

Horizontal Cable Systems ALUMINUM RAILING INSTALLATION INSTRUCTIONS Horizontal Cable Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 1A) Coastal applications: Confirm

More information

INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS

INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.

More information

TIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter

TIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together

More information

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT

More information

Oxford Stalls Installation Instructions

Oxford Stalls Installation Instructions Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or

More information

Assembly Instructions

Assembly Instructions 10' and 12' Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/20/09 Cedar Gazebo Assembly Instructions

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLine Series 1180 DuraLine Series Class-A Fire Rated IMPORTANT: Review these instructions thoroughly prior to installation. FLOOR ANCHORED

More information

WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount

WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount For Wallbed models: Do-It-Yourself Insturction booklet C92 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE

More information

Vigilant Cigar Humidor Vault. Assembly Instructions

Vigilant Cigar Humidor Vault. Assembly Instructions Vigilant Cigar Humidor Vault Assembly Instructions Models: 1000, 1500, and 2000 Congratulations! You have purchased a superior cigar humidor. These humidors have been specifically designed to properly

More information

INOVO 2-LITE SLIDING PATIO DOOR

INOVO 2-LITE SLIDING PATIO DOOR INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.

More information

Assembly Instructions 10 X 10 Aluminum Frame Building

Assembly Instructions 10 X 10 Aluminum Frame Building Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal

More information

Sentinel Electronic Safe Installation Guide

Sentinel Electronic Safe Installation Guide Sentinel Electronic Safe Installation Guide by Rev 07/12/2004 P/N 100020 Table of Contents 1. OVERVIEW...3 2. SAFE INSTALLATION...3 2.1. TOOLS REQUIRED...3 2.2. SELECTING THE MOUNTING LOCATION...3 2.3.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review

More information

ALUMINUM POLE VAULT STANDARDS SPECIFICATIONS

ALUMINUM POLE VAULT STANDARDS SPECIFICATIONS SPECIFICATIONS Specifications: All aluminum construction for superior corrosion resistance. Dual height scales provide English and Metric measurements ranging from 7' to 8'. Wide stance base for improved

More information

Assembly Instructions 10 X 10 Aluminum Roof Support

Assembly Instructions 10 X 10 Aluminum Roof Support Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1

More information

** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at:

** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at: 3/01/2007 VISIT THE LITIME WEB SITE: WWW.LITIME.COM ** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at: 1 (800) 225-3865 Double Shed Doors for Back

More information

Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays

Installation and Assembly: Articulating Swivel Arm for 37 - 60 Flat Panel Displays Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays Models: PLA60, PLA60-S, PLAV60, PLAV60-S Max UL Load Capacity: 175 lb (79 kg) 2300 White Oak Circle Aurora, Il 60502

More information

4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS

4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS 4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS Recommended Tools: Before You Begin: Saftey Glasses, Tape Measure, Carpenters Level, Framing Square, Hex Head Nut Drivers, Chalk Line, Elec.

More information

Qwik-Fence Installation Instructions

Qwik-Fence Installation Instructions Qwik-Fence Installation Instructions 1 Tools Required The following installation instructions should be used as a guide for installing Folding Guard Qwik-Fence Partitions. Good common sense and appropriate

More information

Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors)

Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors) Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors) IMPORTANT: Please read before you begin. Table of Contents

More information

10x10 Trellis Pergola

10x10 Trellis Pergola 0x0 Trellis Pergola ASSEMBLY GUIDE Ver.-007 Table of Contents PAGE 0x0 Trellis Pergola Introduction & Overview...................................................... Pergola Materials Overview..............................................................

More information

Horizontal Cable Systems

Horizontal Cable Systems ALUMINUM RAILING INSTALLATION INSTRUCTIONS v2012 orizontal Cable Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 1A) Coastal applications:

More information

Kwik-Lock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.

Kwik-Lock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered. Serving the Truck & Trailer Industry Since 1944 Installation Instructions Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com

More information

Insolroll Clutch Operated Shades Installation Instructions Installation Instructions

Insolroll Clutch Operated Shades Installation Instructions Installation Instructions All clutch operated shades are shipped fully assembled and ready for installation. Mounting screws are not provided. Screws for chain guide installation to meet the child safety standards are provided.

More information

N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS

N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS 1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems

More information

INSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.

More information

Installation Instructions - Model V4JSD 1

Installation Instructions - Model V4JSD 1 Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)

More information

Architectural Testing AAMA 501 TEST REPORT. Report Number: C Rendered to: Tubelite, Inc. Walker, Michigan

Architectural Testing AAMA 501 TEST REPORT. Report Number: C Rendered to: Tubelite, Inc. Walker, Michigan Architectural Testing AAMA 501 TEST REPORT Report Number: C1529.01-450-44 Rendered to: Tubelite, Inc. Walker, Michigan MODEL DESIGNATION: E4500 PRODUCT TYPE: Non-Thermal Storefront This report contains

More information

For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED

More information

DOCK WEDGE - STANDARD

DOCK WEDGE - STANDARD DOCK WEDGE - STANDARD INSTALLATION INSTRUCTIONS WOOD HEADER READ ALL INSTRUCTIONS BEFORE INSTALLING SEAL. SUPER SEAL MFG. LTD. WILL NOT BE HELD RESPONSIBLE FOR IMPROPER INSTALLATION OF ANCHORING DEVICES,

More information

INSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.

More information

HANDRAIL HEIGHT PER LOCAL CODE AUTHORITY. 6 3/8" [161.9mm]

HANDRAIL HEIGHT PER LOCAL CODE AUTHORITY. 6 3/8 [161.9mm] PLEASE READ PLEASE READ THESE INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING THE INSTALLATION! THIS INSTRUCTION SHEET IS INTENDED TO PROVIDE A SPECIFIC GUIDE TO FOLLOW FOR THE INSTALLATION OF THIS. CONTAINED

More information

Track Rack. * Track Racks are not lockable

Track Rack. * Track Racks are not lockable The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply

More information

Franklin Mills Stackable Movable Lateral Instructions

Franklin Mills Stackable Movable Lateral Instructions Franklin Mills Stackable Movable Lateral Instructions Table of Contents: Table of contents...1 Tools Required...2 Stationary Shelving Assembly...3-7 Mobile Shelving Assembly...8-16 Rail Assembly...8-11

More information

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS 12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions

More information

Bunk Pod Front Entry Assembly Instructions

Bunk Pod Front Entry Assembly Instructions Bunk Pod Front Entry Assembly Instructions www.podtime.co.uk enquiries@podtime.co.uk Working House Ltd How to assemble your pod This step by step guide will show how to assemble your pod(s) on site. It

More information

I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS

I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS Page 2-9: Installation Instructions, Figures 1, 2, & 3 Page 10-12: Figures A-1, A-2, & A-3: Installation

More information

Calf-Tel Pen System Assembly Instructions

Calf-Tel Pen System Assembly Instructions Calf-Tel Pen System Assembly Instructions (Instructions work for 4, 6, and the 7 Pen Systems) 1 ASSEMBLY OF PEN FRONT AND WALLS START THE ASSEMBLY BY LINING UP THE TWO UNI-DIRECTIONAL ARROWS IN THE TOP,

More information

PORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12

PORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12 Page 1 of 7 PORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12 *For Beige Decking Add the Letter B to Model* Thank you for purchasing out product! *Please read these instructions and follow

More information

HOUSE PARTS PACKED IN HOUSE BOX PARTS IN PLASTIC BAG (HARDWARE) PARTS IN SMALL PLASTIC BAG (FLOOR CLIPS) PARTS PACKED IN BUNDLE

HOUSE PARTS PACKED IN HOUSE BOX PARTS IN PLASTIC BAG (HARDWARE) PARTS IN SMALL PLASTIC BAG (FLOOR CLIPS) PARTS PACKED IN BUNDLE Check parts against this list before starting assembly. Refer to illustrations on pages 6 and 7 to view house parts. If any shortages are found, refer to Packing Slip for claim instructions. Item 3 5 6

More information

Installation Manual For ToddPod Outdoor Shower Enclosures

Installation Manual For ToddPod Outdoor Shower Enclosures Installation Manual For ToddPod Outdoor Shower Enclosures Contact us at 888-545-9763 or email us at office@toddpod.com with any questions during the installation process. Our service team is available

More information

https://www.wallbedsbywilding.com/wallbed-installation-studio-series/

https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last

More information

TREX POST MOUNT DECKING AND CONCRETE

TREX POST MOUNT DECKING AND CONCRETE TREX POST MOUNT DECKING AND CONCRETE for Pressure-treated Wood Framing LOCATION AND INSTALLATION OF POST MOUNTS IMPORTANT NOTES:» EACH POST MUST BE ATTACHED AS SHOWN TO ENSURE A CODE COMPLIANT AND SAFE

More information

Unit No. 4400, 4500 Classic Frameless Sliding Tub/Shower Enclosure INSTALLATION INSTRUCTIONS

Unit No. 4400, 4500 Classic Frameless Sliding Tub/Shower Enclosure INSTALLATION INSTRUCTIONS Unit No. 4400, 4500 Classic Frameless Sliding Tub/Shower Enclosure INSTALLATION INSTRUCTIONS MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure: tempered glass and anodized

More information

End of Row Doors. Revision Number 1

End of Row Doors. Revision Number 1 End of Row Doors Single Swing Door Café Style Doors Revision Number 1 Wright Line LLC 160 Gold Star Boulevard Worcester, MA 01606 Tel: 800-225-7348 508-852-4300 Fax: 508-365-6178 www.wrightline.com info@wrightline.com

More information

PH03 Comfort XL Front Assembly Replacement Instructions

PH03 Comfort XL Front Assembly Replacement Instructions PH03 Comfort XL Front Assembly Replacement Instructions POLYJOHN USA PolyJohn Enterprises Corp 2500 Gaspar Ave. Whiting, IN 46394 Phone: 800-292-1305 Fax: 219-659-0625 www.polyjohn.com info@polyjohn.com

More information

Quick Fit Installation Guide Retractable Screen - Double Door

Quick Fit Installation Guide Retractable Screen - Double Door Quick Fit Installation Guide Retractable Screen - Double Door 1 REMOVE KIT PARTS FROM SHIPPING TUBE 2 Slide bolts 2 Rail receiver Clips 15 Mounting screws 1 Housing end cap screw 2 Handles 1 Housing end

More information

Thank you for purchasing out product! *Please read these instructions and follow them step by step. *

Thank you for purchasing out product! *Please read these instructions and follow them step by step. * Page 1 of 7 AD17 AA DS 4 X 16 T12 Thank you for purchasing out product! *Please read these instructions and follow them step by step. * STEP 1. Slide two support posts (REF. # 24) into the two outside

More information

INSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD

INSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION

More information

10x10 Trellis Pergola

10x10 Trellis Pergola 0x0 Trellis Pergola ASSEMBLY GUIDE Ver.0-7 Table of Contents PAGE Introduction & Overview...................................................... Pergola Materials Overview..............................................................

More information

Classic Roll Tarp. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.

Classic Roll Tarp. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered. Serving the Truck & Trailer Industry Since 1944 Classic Roll Tarp Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com

More information

Sliding Glass Door Assembly and Installation Guide

Sliding Glass Door Assembly and Installation Guide Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all

More information

PROFILE Flat Panel Console System Installation Manual

PROFILE Flat Panel Console System Installation Manual PROFILE Flat Panel Console System Installation Manual Table of Contents Page Introduction... 2 Important Safety Information...3, 4 Installation Overview... 4, 5, 6 Single Sided/Single Unit... 7 Double

More information

Classic Roll Tarp. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.

Classic Roll Tarp. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered. Serving the Truck & Trailer Industry Since 1944 Classic Roll Tarp Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com

More information

ICU TRACKLESS SLIDING DOOR

ICU TRACKLESS SLIDING DOOR Interior View 0 Installation Instructions Tools Required: Screwdrivers Small Straight (Flat Blade) - for Terminal Block wiring # Phillips (Crosspoint) - for various #8, #0, and #4 screws Wrenches / Sockets

More information

INSTRUCTION BOOKLET #C20

INSTRUCTION BOOKLET #C20 INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO

More information

RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS

RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.

More information

Dura-Lock Roof System

Dura-Lock Roof System DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.

More information

Installation Instructions

Installation Instructions EZ Launch Accessible Transfer System Installation Instructions Models 500900L, 500900R, 500901L, 500901R 500890, 500906L, 500906R For questions about features, operation/performance, parts, accessories

More information

Assembly Instructions

Assembly Instructions Laminate/Phenolic & 1 Pc Butcherblock Tops Before you begin, please make sure all parts and proper quantities are included. (See on next page) Any parts damaged during shipment must be reported within

More information

Otter Pro XT Cottage Installation and Set-Up Instructions

Otter Pro XT Cottage Installation and Set-Up Instructions Otter Pro XT Cottage Installation and Set-Up Instructions Otter Pro XT Cottage Fits Small Ultra-Wide Otter Pro and Otter II Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Pro

More information

Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models

Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly

More information

PFT CABLE GYM INSTRUCTION MANUAL

PFT CABLE GYM INSTRUCTION MANUAL PFT CABLE GYM INSTRUCTION MANUAL QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will guarantee your

More information

For additional assistance call

For additional assistance call The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or

More information

Linear Hook- on Worksurfaces

Linear Hook- on Worksurfaces Linear Hook- on Worksurfaces Linear Hook-On Worksurfaces come in three depths and seven lengths. Different worksurfaces have different reqirements for installation that are outlined below. 27 inch deep

More information

INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE:

INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE: INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE: 268 June 22, 2010 TOOLS NEEDED COMPONENTS INCLUDED P2 Tip 3/8" Drill Rubber Gasket(s) x 2 Bracket(s) x 2 1/2" Drill Bit Bulkhead Flange #2 Phillips

More information

IDR assembly instructions:

IDR assembly instructions: IDR assembly instructions: Required Tools: 2 X 12mm Open End Wrench 14mm open end wrench #2 Phillips Head Screw Driver (Drill with adjustable torque clutch recommended) 8mm nut driver (Supplied in IDR-AK)

More information

LEGENDS RETRACTABLE DOOR SCREENS

LEGENDS RETRACTABLE DOOR SCREENS LEGENDS RETRACTABLE DOOR SCREENS MAGNETIC LATCHING DESIGN SYSTEM 42 I N S T A L L A T I O N I N S T R U C T I O N S 1 MOUNTING OPTIONS Recess : Mount the Screen Cassette using Recess Mounting Clips Recess

More information

3 BRACKET TO GUIDE ATTACHMENT. RIGHT END Figure 1. EXTENDED BRACKET (for doors taller than 8-8 ) SERIES 650. RIGHT END COTTER PIN Figure 6

3 BRACKET TO GUIDE ATTACHMENT. RIGHT END Figure 1. EXTENDED BRACKET (for doors taller than 8-8 ) SERIES 650. RIGHT END COTTER PIN Figure 6 2 DOOR ARRANGEMENT. A Lay door on a clean floor inside of building and in front of opening (see Figure 1). NOTE: Door can be damaged if laid on unclean surface. B Distribute parts bags, guides, stops and

More information

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding

More information

IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS FOR AZTEC SHELTER

IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS FOR AZTEC SHELTER IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS FOR AZTEC SHELTER ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION

More information

Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays

Installation and Assembly: Flat Video Wall Mount For 40 to 65 Flat Panel Displays Installation and Assembly: Flat Video Wall Mount For 40" to 65" Flat Panel Displays Model: DS-VW665 Maximum Load Capacity: 125 lb (57 kg) 1 of 11 ISSUED: 03-22-12 SHEET #: 125-9288-4 06-25-13 NOTE: Read

More information

IMPORTANT: installation. FLOOR ANCHORED CEILING HUNG OVERHEAD BRACED FLOOR-TO- CEILING ANCHORED

IMPORTANT: installation. FLOOR ANCHORED CEILING HUNG OVERHEAD BRACED FLOOR-TO- CEILING ANCHORED INSTALLATION INSTRUCTIONS MAXIMUM PRIVACY COMPACT LAMINATE TOILET PARTITIONS 2080 DuraLineSeries 2180 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and

More information

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16 Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete

More information

Spring Loaded All Season Roll-Up Doors

Spring Loaded All Season Roll-Up Doors Spring Loaded All Season Roll-Up Doors STAND-OFF MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged, immediately

More information

OB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount

OB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount INSTALLATION INSTRUCTIONS Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description

More information

INSTALLING YOUR NEW SPRING LIFT ARM KIT

INSTALLING YOUR NEW SPRING LIFT ARM KIT INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as

More information