Section 75-AA-1. Flaperon Assembly

Size: px
Start display at page:

Download "Section 75-AA-1. Flaperon Assembly"

Transcription

1 Section 75-AA-1 This manual has been prepared for assembly of the flaperons supplied with match drilled parts. This photo assembly manual is intended as a supplement to the drawings. If there is any discrepancy between this manual and the drawings, the drawings supersede this manual. For more information on building standards and allowable tolerances see Construction Standards for Zenair Light Aircraft available from Zenith Aircraft Co. Section 75-AA-1, Page 1 of 15

2 P/N: 75A1-2 Flaperon Nose Rib P/N: 75A1-3 Flaperon Rear Rib P/N: 75A1-4 I/B Flaperon Spar or 75A1-5 O/B Flaperon Spar Cleco the Rear Ribs and Nose Ribs to the Spar. See drawing 75-AA-1 for the Rib locations. Orientation: The Rear Rib flanges point outboard. The inboard Nose Rib flanges point inboard and the outboard Nose Rib flanges point outboard. The top flange of the Spar is bent beyond 90 degrees. With a #30 drill bit, expand the holes. Disassemble the Ribs from the Spar. Deburr, reassemble, and rivet the Ribs to the Spar. P/N: 75A2-1 Hinge Bracket Draw a center line on both flanges of the Hinge Bracket. Place a mark on both flanges 9mm from the top of the Hinge Bracket. Place a second mark on both flanges 20mm from the first mark. With a #40 drill bit, drill the rivet holes on the marks. Section 75-AA-1, Page 2 of 15

3 Clamp the Hinge Bracket on the Spar against the Nose Rib: Measure 26mm from the top of the spar flange to the end of the bracket. Back drill through the Hinge Bracket into the Spar, Cleco the Hinge Bracket to the Spar then back drill into the Nose Rib. With a #20 drill bit, expand the holes. With the Hinge Bracket Clecoed to the Spar and Nose Rib, mark a diagonal line from the bottom of the Spar to the inside corner of the Hinge Bracket Trim the Hinge Bracket on the line. This is most easily done with a band saw but can be cut with a hack saw as well. File the saw tooth marks smooth after cutting. Deburr and rivet the Hinge Bracket to the Spar and Nose Ribs. Section 75-AA-1, Page 3 of 15

4 Rivet the spar assembly For bracket, the rivet head is set on the thinner material. Square the rib and drill the rib flange through the pre-drilled hole in the spar. P/N: 75A1-8 I/B Flaperon Skin Or P/N: 75A1-9 O/B Flaperon Skin Open up the holes in the skin and skeleton with a #30 drill Section 75-AA-1, Page 4 of 15

5 Debur the holes, and apply corrosion protection. To avoid damage to the skin, the parts are riveted the first time they are clecoed. Cleco the rear ribs to the skin. Add weights on the skin to keep the assembly flat on the workbench. Section 75-AA-1, Page 5 of 15

6 Keep the weights on the skin and cleco the ribs to the spar P/N: 75A1-1 Flaperon Full Rib Section 75-AA-1, Page 6 of 15

7 Cleco the full rib to the skin Turn the assembly over and cleco a hole to keep the rib in place. Section 75-AA-1, Page 7 of 15

8 P/N: 75A2-3 Flaperon Rib Angle Draw a center line on the small flange of the Rib Angle. On the longer flange, measure 10mmm from the edge and mark a line. Mark rivet locations 10mm from the top and bottom of each flange. With a #40 drill bit, predrill the holes in the flanges. Position the Rib Angle against the Spar and clamp it to the Full Rib. Note: You may need to crop the top corner of the Rib Angle to properly fit between the flanges of the Full Back drill through the Rib Angle into the Spar. Rivet the angle to the spar. Section 75-AA-1, Page 8 of 15

9 Back drill into the full rib and cleco Rivet the rib on the bottom side. Section 75-AA-1, Page 9 of 15

10 Turn the assembly over and lay weights on the skin to keep the trailing edge straight and to assure there is no twist. Drill and Cleco through the spar. Section 75-AA-1, Page 10 of 15

11 Cleco the ribs Drill all the holes and rivet. Rivet the top side: rear ribs and spar. Section 75-AA-1, Page 11 of 15

12 Use a furring strip to bring the Skin around the Nose Ribs and Cleco the Skin to the Spar. This is best done with one person pushing on the furring strip and one person Clecoing the holes. Alternatively, ratchet straps can be used. Cleco at least every other hole. Section 75-AA-1, Page 12 of 15

13 Position the weights beside the rear ribs. There should be no twist: the assembly sits flat on the workbench. Run a #30 drill through the holes and rivet. Section 75-AA-1, Page 13 of 15

14 P/N: 75A2-4 Flaperon Tip For the outboard section only. The skin will overlap the flaperon tip on 20mm. For a tight fit at the leading edge, trim the flaperon tip to reduce the overlap at the leading edge to approximately 3mm. Position for the best fit by closing the gap at the front. Section 75-AA-1, Page 14 of 15

15 A gap at the back is normal. P/N: C75A1-6 Flaperon control horn P/N: L angle Installed on the bottom side I/B end of I/B flaperon section Section 75-AA-1, Page 15 of 15

75-TA-4. Elevator Skins

75-TA-4. Elevator Skins 75-TA-4 This manual has been prepared for assembly of the. This photo assembly manual is intended as a supplement to the drawings. If there is any discrepancy between this manual and the drawings, the

More information

Section C75-WA-1. Wing Skeleton

Section C75-WA-1. Wing Skeleton Section C75-WA-1 This manual has been prepared for assembly of the wing skeleton supplied with match drilled parts. This photo assembly manual is intended as a supplement to the drawings. If there is any

More information

Section 75-ZA-2. Rudder Mounting

Section 75-ZA-2. Rudder Mounting Section 75-ZA-2 This manual has been prepared for installation of the Rudder. This photo assembly manual is intended as a supplement to the drawings. If there is any discrepancy between this manual and

More information

Section 6-T-3 Elevator

Section 6-T-3 Elevator Section 6-T-3 Elevator This manual has been prepared for assembly of the Elevator using match drilled parts. This photo assembly manual is intended as a supplement to the drawings. If there is any discrepancy

More information

Section 75-SA-1 Slat Section

Section 75-SA-1 Slat Section Section 75-SA-1 Slat Section This manual has been prepared for assembly of the slat sections supplied with match drilled parts. This photo assembly manual is intended as a supplement to the drawings. If

More information

Three vertical L angles must be riveted to each main spar (length = 206mm see boxed diagram on drawing 7-V-2).

Three vertical L angles must be riveted to each main spar (length = 206mm see boxed diagram on drawing 7-V-2). Cut over-sized (left); Trim and file (above). Note: Six needed. Three vertical L angles must be riveted to each main spar (length = 206mm see boxed diagram on drawing 7-V-2). Trace line down center of

More information

Section 6-B-4 Rear Fuselage Riveting

Section 6-B-4 Rear Fuselage Riveting Section 6-B-4 Rear Fuselage Riveting This manual has been prepared for assembly of the rear fuselage. This photo assembly manual is intended as a supplement to the drawings. If there is any discrepancy

More information

FLAPERON ASSEMBLY. Ref. Drawing 8XA-1 Exploded view SECTION 1 REAR SKIN AND NOSE RIBS ASSEMBLY

FLAPERON ASSEMBLY. Ref. Drawing 8XA-1 Exploded view SECTION 1 REAR SKIN AND NOSE RIBS ASSEMBLY Ref. Drawing 8XA-1 Exploded view SECTION 1 REAR SKIN AND NOSE RIBS ASSEMBLY The slope on the back side of each hinge bracket 8A1-5 face inboard towards the fuselage for both the left and right wing Work

More information

STOL CH 701. Clamp a reference extrusion on the bottom of the spar. Clamp the bottom flange of the rib to the extrusion. Rear Root Rib 7V4-2

STOL CH 701. Clamp a reference extrusion on the bottom of the spar. Clamp the bottom flange of the rib to the extrusion. Rear Root Rib 7V4-2 Rear Root Rib 7V4-2 Clamp a reference extrusion on the bottom of the spar. Clamp the bottom flange of the rib to the extrusion. Cleco the root nose rib to the spar Position the rear root rib at station

More information

Section 6-B-6, 6-B-7, & 6-B-8 Firewall Assembly

Section 6-B-6, 6-B-7, & 6-B-8 Firewall Assembly Section 6-B-6, 6-B-7, & 6-B-8 Firewall Assembly This manual has been prepared for assembly of the firewall supplied with match drilled parts. This photo assembly manual is intended as a supplement to the

More information

Check the jig with the Slat Ribs. Notice the front tip is cut off, this will allow the slat to fit in the jig correctly.

Check the jig with the Slat Ribs. Notice the front tip is cut off, this will allow the slat to fit in the jig correctly. Slat Jig A slat jig will be needed to obtain the correct curvature of the slat. The Slat drawing is located on 7-F-13, cutout and trace on plywood. The length of the jig is 1830mm, which is the outboard

More information

Section 75-FA-5. Firewall Assembly

Section 75-FA-5. Firewall Assembly Section 75-FA-5 This manual has been prepared for assembly of the firewall supplied with match drilled parts. This photo assembly manual is intended as a supplement to the drawings. If there is any discrepancy

More information

Section C75-FA-2 Top Fuselage Skin & Rear Fuselage Assembly

Section C75-FA-2 Top Fuselage Skin & Rear Fuselage Assembly Section C75-FA-2 Top Fuselage Skin & Rear Fuselage This manual has been prepared for assembly of the rear fuselage supplied with match drilled parts. This photo assembly manual is intended as a supplement

More information

STOL CH 701. Standard L ANGLES are supplied in 4ft length. Ref. bottom left diagram on drawing 7-V-2

STOL CH 701. Standard L ANGLES are supplied in 4ft length. Ref. bottom left diagram on drawing 7-V-2 Standard L ANGLES are supplied in 4ft length. Ref. bottom left diagram on drawing 7-V-2 Length = 206mm. Layout the cut line on the outside flanges. Ref. see boxed diagram on drawing 7-V-2 Three vertical

More information

STOL CH H3-3SP Center Hinge Bracket. IMPORTANT: The Bracket 7H5-3SP is not symmetrical

STOL CH H3-3SP Center Hinge Bracket. IMPORTANT: The Bracket 7H5-3SP is not symmetrical 7H3-3SP Center Hinge Bracket IMPORTANT: The Bracket 7H5-3SP is not symmetrical Using a square helps layout and mark the perpendicular and the hinge hole. Note: Position of 1/4 hinge hole is 115.5mm from

More information

Section 75-FA-2 Top Fuselage Skin & Rear Fuselage Assembly

Section 75-FA-2 Top Fuselage Skin & Rear Fuselage Assembly Section 75-FA-2 Top Fuselage Skin & Rear Fuselage This manual has been prepared for assembly of the rear fuselage supplied with match drilled parts. This photo assembly manual is intended as a supplement

More information

ZODIAC 601 XL. ZODIAC CH 601 Series. Parts are labeled for easy identification with a part number and description:

ZODIAC 601 XL. ZODIAC CH 601 Series. Parts are labeled for easy identification with a part number and description: CH 601 Series Parts are labeled for easy identification with a part number and description: Part number example: 6T4-4 Vertical Tail Spar 6 - Zodiac CH 601 model T - Rudder section of the Aircraft drawings.

More information

ZODIAC CH650. ZODIAC CH 650 Series. Parts are labeled for easy identification with a part number and description:

ZODIAC CH650. ZODIAC CH 650 Series. Parts are labeled for easy identification with a part number and description: CH 650 Series Parts are labeled for easy identification with a part number and description: Part number example: 6T4-4 Vertical Tail Spar 6 - Zodiac CH 650 model T - Rudder section of the Aircraft drawings.

More information

STOL CH 701. Layout the cut line along the bend tangent line on the web. 7V6-1 and 7V6-2SP

STOL CH 701. Layout the cut line along the bend tangent line on the web. 7V6-1 and 7V6-2SP Layout the cut line along the bend tangent line on the web. 7V6-1 and 7V6-2SP ORIENTATION: 90 degree flange is up Layout the bend line, 20mm from the end. Ref. bottom right diagram 7-V-6 Use a square to

More information

ZODIAC CH 601 Series Kit Aircraft

ZODIAC CH 601 Series Kit Aircraft ZODIAC CH 601 Series Kit Aircraft THE FOLLOWING IS A DRAFT MANUAL This manual has been written and published strictly for informational purpose. It has been prepared as a guide to facilitate the assembly

More information

ZODIAC CH 601 Series Kit Aircraft

ZODIAC CH 601 Series Kit Aircraft ZODIAC CH 601 Series Kit Aircraft THE FOLLOWING IS A DRAFT MANUAL This manual has been written and published strictly for informational purpose. It has been prepared as a guide to facilitate the assembly

More information

Elevator Assembly. To assemble the SR3500 Elevator, you will need the following tools:

Elevator Assembly. To assemble the SR3500 Elevator, you will need the following tools: Elevator Assembly To assemble the SR3500 Elevator, you will need the following tools: 1. Drill 2. Tape Measure 3. Felt Marker 4. #40, #30, 3/16, #11 Drill Bits 5. #40, #30 and 3/16 Clecos 6. Cleco Pliers

More information

STOL CH 801 SECTION 2: Nose Rib 8R1-7

STOL CH 801 SECTION 2: Nose Rib 8R1-7 SECTION 2: Nose Rib 8R1-7 Position the lower nose rib on the front of the spar at the predrilled holes just above rear rib #3 (615mm from the bottom of the spar) Check lateral alignment (rib is centered

More information

CENTER WING SECTION (CWS) WORK REPORT

CENTER WING SECTION (CWS) WORK REPORT CENTER WING SECTION (CWS) WORK REPORT No. Check Parts / Description Qty PHASE 1: Preparations 1 [ ] 6V1-3 Rear ribs 2R & 2L 1 [ ] L Angle 6 2 [ ] 6V2-1 Rear Ribs.032 2R & 2L 2 [ ] 6V5-1 Gear Rib Doubler

More information

WING ASSEMBLY SECTION 4. Mounting Wing Ribs to Main Spar. 1. Identify the proper locations for those ribs with attachment brackets.

WING ASSEMBLY SECTION 4. Mounting Wing Ribs to Main Spar. 1. Identify the proper locations for those ribs with attachment brackets. WING ASSEMBLY SECTION 4 Mounting Wing Ribs to Main Spar Compass Check 1. Identify the proper locations for those ribs with attachment brackets. 2. Position and drill the nose ribs. 3. Un-cleco the nose

More information

Photo-Guide (ZE & ZE )

Photo-Guide (ZE & ZE ) Photo-Guide (ZE-2009-05 & ZE-2009-07) The following photo-guide is for educational purposes only. It is intended to assist owners and/or aircraft mechanics with the installation of elements from from 6Z-1G

More information

ZODIAC 601 XL. Detail of outboard end. Full length recessed elevator trim tab. Detail of inboard end. Trim tab along left trailing edge of elevator.

ZODIAC 601 XL. Detail of outboard end. Full length recessed elevator trim tab. Detail of inboard end. Trim tab along left trailing edge of elevator. Full length recessed elevator trim tab. Detail of outboard end. Detail of inboard end. Trim tab along left trailing edge of elevator. Trim tab in neutral position 6-T-6 - Page 1 of 12 Drill out the middle

More information

2.1 Parts List Tool requirement Before you start assembling the Stabiliser Front Spar Center Doublers...

2.1 Parts List Tool requirement Before you start assembling the Stabiliser Front Spar Center Doublers... Stabilizer Assembly 2.0 Exploded View...Error! Bookmark not defined. 2.1 Parts List...3 2.2 Tool requirement...5 2.3 Before you start assembling the Stabiliser...6 2.4 Front Spar...6 2.5 Center Doublers...7

More information

REAR FUSELAGE ASSEMBLY

REAR FUSELAGE ASSEMBLY SECTION 2 Rear Fuselage Bottom Assembly Ref Dwg 8FR-2 SECTION 2 - Page 1 of 17 FUSELAGE BOTTOM SKIN 8F2-3A Note: The edges of skin 8F2-3A are not a straight line. Check: edge distance from the center of

More information

Section 75-CA-3. Rudder Controls

Section 75-CA-3. Rudder Controls Section 75-CA-3 This manual has been prepared for assembly of the. This photo assembly manual is intended as a supplement to the drawings. If there is any discrepancy between this manual and the drawings,

More information

77.5 degrees REAR CHANNEL PLYWOOD TEMPLATE

77.5 degrees REAR CHANNEL PLYWOOD TEMPLATE 77.5 degrees REAR CHANNEL PLYWOOD TEMPLATE Ref. 6-B-14 Make following template: Vertical distance = 300mm Layout dimensions shown in the bottom right table on drawing 6-B-14 Top and bottom are square to

More information

Flaperon Assembly Manual

Flaperon Assembly Manual Flaperon Assembly Manual for PegaStol Aftermarket Wings A Senior Project presented to The Faculty of the Aerospace Engineering Department California Polytechnic State University, San Luis Obispo In Partial

More information

ZODIAC 601 XL UPRIGHT CHANNELS 6B5-6. Top and bottom outboard flange is joggle to overlap the.093 extrusion 6B2-3 and 6B11-1

ZODIAC 601 XL UPRIGHT CHANNELS 6B5-6. Top and bottom outboard flange is joggle to overlap the.093 extrusion 6B2-3 and 6B11-1 UPRIGHT CHANNELS 6B5-6 Top and bottom outboard flange is joggle to overlap the.093 extrusion 6B2-3 and 6B11-1 Length: fits between the bottom and top longerons. Clamp the upright channel to the rear frame

More information

Cut the center and pre-drill the Hinge Plate. Do not drill the Rudder Hinge hole at this time.

Cut the center and pre-drill the Hinge Plate. Do not drill the Rudder Hinge hole at this time. 7F4-1 Upper Rudder Hinge Plate Layout the cut for the Upper Hinge Plate. Measure and mark the center for the Rudder Hinge. The center hinge hole is 75mm from the back edge of 7F4-1. Cut the center and

More information

FORWARD FUSELAGE ASSEMBLY

FORWARD FUSELAGE ASSEMBLY SECTION 2 Finishing the Firewall RIVETS: SA5 or A5 (all rivets on the firewall, rivet head set from the engine side) SUGGESTION: First drill undersize pilot hole #30 or #40, then open with #20 SECTION

More information

ZODIAC 601 XL. REAR RIBS 6W6-1 to 6W6-9. Reference to drawing 6-W-00 for orientations of ribs flanges. Rear ribs are tapered: rib #9 is the shortest.

ZODIAC 601 XL. REAR RIBS 6W6-1 to 6W6-9. Reference to drawing 6-W-00 for orientations of ribs flanges. Rear ribs are tapered: rib #9 is the shortest. REAR RIBS 6W6-1 to 6W6-9 Reference to drawing 6-W-00 for orientations of ribs flanges. Rear ribs are tapered: rib #9 is the shortest. Right wing Zodiac CH 6-W-6 - Page 1 of 12 Burr on edge of flanged lightening

More information

STOL CH st Edition 1 st Revision Drawings Summary of changes from Edition 1 to Edition 1 Revision 1.

STOL CH st Edition 1 st Revision Drawings Summary of changes from Edition 1 to Edition 1 Revision 1. STOL CH 750 1 st Edition 1 st Revision Drawings Summary of changes from Edition 1 to Edition 1 Revision 1. Page Date Drawing Title 75-G-0 01/10 Three View Drawing 75-G-1 01/10 Drawings Index 75-RX-1 05/09

More information

STOL CH F2-2 Side Skin

STOL CH F2-2 Side Skin 7F2-2 Side Skin IMPORTANT: See drawing 7F2-2 to identify the topside of the skin, also clearly mark the side that will be on the inside of the fuselage (if possible choose the side with the manufacture

More information

WING ASSEMBLY 23.5 (Continued)

WING ASSEMBLY 23.5 (Continued) A VERY IMPORTANT NOTE found on many wing drawings states Do not drill any unspecified holes into spar. This is extremely important as any extra holes may, under extreme conditions, WEAKEN THE SPAR. Note;

More information

Page: REV 2: Added "Step 1: Straighten the W-0007B Rear Spar Reinforcement Fork as described on Page 10-03, Step 4."

Page: REV 2: Added Step 1: Straighten the W-0007B Rear Spar Reinforcement Fork as described on Page 10-03, Step 4. 14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION

More information

REVISION DESCRIPTION:

REVISION DESCRIPTION: REVISION DESCRIPTION: Page: 09-10 REV 1: Delete Step 1. 14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and

More information

11) Chromate the mating surfaces of the Leading edge Root Rib, Doubler and Root Rib Stiffeners. Rivet together with 1/8 rivets (RV-1410).

11) Chromate the mating surfaces of the Leading edge Root Rib, Doubler and Root Rib Stiffeners. Rivet together with 1/8 rivets (RV-1410). 11) Chromate the mating surfaces of the Leading edge Root Rib, Doubler and Root Rib Stiffeners. Rivet together with 1/8 rivets (RV-1410). 12) Chromate the Root Rib Attach Bracket and rivet to the Root

More information

Horizontal Stabilizer Service Bulletin

Horizontal Stabilizer Service Bulletin Horizontal Stabilizer Service Bulletin Date: Friday November 19, 2004 To: All Super Rebel/Moose owners Re: Horizontal stabilizer tip rib INFO: A number of Super Rebels have shown cracking on the tip rib/rear

More information

9.3 FUSELAGE ASSEMBLY 14/03/02

9.3 FUSELAGE ASSEMBLY 14/03/02 9.3 MATING THE TAIL CONE TO THE CABIN 1) Trim the bottom flange of both FUS-339 side skins on the tailcone assembly as in Figure 1. 2) Remove the bottom two RBULK 2A s of bulkhead A on the tailcone. 3)

More information

10. Wing prep and subassembly

10. Wing prep and subassembly Date Section Objective: Construct and fabricate the sub-assemblies of the wing panel. Required Parts: Wing left 11gal PN104-300, Wing right 1gal PN104-400, Wing left 15 gal option PN104-322, Wing right

More information

STOL CH nd Edition Drawings July 20, 2010 Summary of changes from Edition 1 to Edition 2.

STOL CH nd Edition Drawings July 20, 2010 Summary of changes from Edition 1 to Edition 2. STOL CH 750 2 nd Edition Drawings July 20, 2010 Summary of changes from Edition 1 to Edition 2. Page Date Drawing Title 75-G-0 07/10 Three View Drawing 75-G-1 07/10 Drawings Index 75-G-2 03/10 General

More information

FLAP AILERON FLAP / FUSE SEAL KIT

FLAP AILERON FLAP / FUSE SEAL KIT FLAP AILERON FLAP / FUSE SEAL KIT APPLICABLE MODELS BEECHCRAFT MODELS 33/35/36 I N S T A L L A T I O N M A N U A L I S S U E D A T E 06/06/84 KNOTS 2U, LTD. 709 AIRPORT ROAD BURLINGTON, WI 53105 262 763-5100

More information

ZODIAC CH 601 Series Kit Aircraft

ZODIAC CH 601 Series Kit Aircraft ZODIAC CH 601 Series Kit Aircraft THE FOLLOWING IS A DRAFT MANUAL This manual has been written and published strictly for informational purpose. It has been prepared as a guide to facilitate the assembly

More information

FINAL ASSEMBLY- DOORS

FINAL ASSEMBLY- DOORS - DOORS DRAWING 8XF-5 ASSEMBLY OF THE DOORS CONTENTS SECTIONS #4a DOOR FRAME #4b DOOR GUSSETS & BOTTOM SKIN #4c DOOR LATCH & STOP Helpful building tips: Use a flat, unwrapped piece of plywood for the door

More information

FORWARD FUSELAGE SIDES & REAR TOP SKINS

FORWARD FUSELAGE SIDES & REAR TOP SKINS FORWARD FUSELAGE SIDES & REAR TOP SKINS WORK REPORT Step No. Check Parts / Tools Qty Preparations. 1 [ ] 6F5-3 Upper Front Longerons 2 2 [ ] 6F5-5 Heel Support 1 3 [ ] 6F5-2 Front Floor Skin 1 3 [ ] Firewall

More information

Page: REV 1: Step 5 and Figure 5 updated to better describe the potential necessity of modifying a rivet squeezer yoke.

Page: REV 1: Step 5 and Figure 5 updated to better describe the potential necessity of modifying a rivet squeezer yoke. 14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm REVISION

More information

Section 6-K-1 Fuel Sender Unit Installation

Section 6-K-1 Fuel Sender Unit Installation Section 6-K-1 Fuel Sender Unit Installation This manual has been prepared for installation of the fuel sender unit. This photo assembly manual is intended as a supplement to the drawings. If there is any

More information

SERVICE BULLETIN

SERVICE BULLETIN SERVICE BULLETIN 14-02-03 Date Released: February 3, 2014 Date Effective: February 3, 2014 Subject: Affected Models: Required Action: Time of Compliance: Cracking in elevator spar web near elevator attach

More information

Ch. 9.0 ELITE FUSELAGE ASSEMBLY 14/02/2003

Ch. 9.0 ELITE FUSELAGE ASSEMBLY 14/02/2003 Fuselage Assembly In the front of the fuselage manual you will find an exploded view of the fuselage and a side view schematic. We suggest that you tape these to the wall of your workshop. Refer to them

More information

SERVICE BULLETIN

SERVICE BULLETIN SERVICE BULLETIN 16-03-28 Date Released: May 6, 2016 (Initial Release) June 2, 2016 (Added Note, pg.11) Date Effective: May 6, 2016 Affected Models: Subject: Required Action: All RV-3, 4, 6/6A, 7/7A, 8/8A,

More information

REAR FUSELAGE ASSEMBLY

REAR FUSELAGE ASSEMBLY SECTION 5 Tail Attachments on Fuselage Ref Dwg 8RU-3 The rudder hinge line (HL) is parallel to the aft edge of the fuselage skin SECTION 5 - Page 1 of 9 Looking at the top of the rear fuselage. Stabilizer

More information

12. Wings, Flaps, Ailerons and Struts

12. Wings, Flaps, Ailerons and Struts 12. Wings, Flaps, Ailerons and Struts Fit Aileron Hinges Reference: Drawing 20270K2 Photo 12.1 Parts Required: 2007092 Aileron LS 200809N Aileron RS 2001394 Hinge 3/16 A1 (4) 2001694 Hinge Pin (4) PH0059N

More information

ZODIAC CH 601 XL 6TD3-1 TD MAIN GEAR UPRIGHTS (QTY=1L + 1R) Cutout in the side skin is below the diagonal rivet line.

ZODIAC CH 601 XL 6TD3-1 TD MAIN GEAR UPRIGHTS (QTY=1L + 1R) Cutout in the side skin is below the diagonal rivet line. 6TD3-1 TD MAIN GEAR UPRIGHTS (QTY=1L + 1R) Cutout in the side skin is below the diagonal rivet line. The TD Gear Upright 6TD3-1 is installed on top of the landing gear 6TD2-7. 6TD3-1 makes the corner between

More information

WING ASSEMBLY SLAT SUPPORT AND NOSE RIB ASSEMBLY PREPARING THE STANDARD L ANGLES SECTION 2 STOL CH 801. Compass Check

WING ASSEMBLY SLAT SUPPORT AND NOSE RIB ASSEMBLY PREPARING THE STANDARD L ANGLES SECTION 2 STOL CH 801. Compass Check WING ASSEMBLY SECTION 2 SLAT SUPPORT AND NOSE RIB ASSEMBLY PREPARING THE STANDARD L ANGLES Compass Check 1. Prepare eight pieces of standard L angle. 2. Make the assembly fixture. 3. Drill all holes -

More information

After the canopy hinge is square with the firewall and the nut plates are installed you can set up the hinge mounts. Start by clamping a 1/16 tongue

After the canopy hinge is square with the firewall and the nut plates are installed you can set up the hinge mounts. Start by clamping a 1/16 tongue Written by: Sean Cole September 19, 2008 When fitting the stiffener use 3/32 clecos to hold it in place, it makes a smaller hole and is easier to work with. Only use the amount needed to hold the stiffener

More information

ZODIAC 601 XL. Outside Flashing 6C3-3. Mark the no rivet zone for Extrusion Handle 6C3-8

ZODIAC 601 XL. Outside Flashing 6C3-3. Mark the no rivet zone for Extrusion Handle 6C3-8 Outside Flashing 6C3-3 Mark the no rivet zone for Extrusion Handle 6C3-8 Cleco the inside and outside flashing to the canopy side frame before the canopy bubble is fitted. Ref. Front edge 50mm back from

More information

Chap. 9.2 SR3500 Fuselage Assembly - Cabin. MODEL: SR Murphy Aircraft Mfg. Ltd. All rights reserved.

Chap. 9.2 SR3500 Fuselage Assembly - Cabin. MODEL: SR Murphy Aircraft Mfg. Ltd. All rights reserved. 26/06/2006 Page 1 26/06/2006 Page 2 26/06/2006 Page 3 Parts List for Gear Box No. Part Number Description Qty Required 1,23 FUS0711QL BRACING CHANNEL 2 2,22 FUS0711QR BRACING CHANNEL 2 3 FUS301QB CARRYTHROUGH

More information

Pre-Paint>Wings>Fit ailerons. Objectives of this task: Materials and equipment required: Size the ailerons and pre-mould strips

Pre-Paint>Wings>Fit ailerons. Objectives of this task: Materials and equipment required: Size the ailerons and pre-mould strips Pre-Paint>Wings>Fit ailerons Objectives of this task: In this task the ailerons and the pre-mould strips will be sized and trimmed, then flocked onto the wings and glassed in place, and the next day the

More information

American Champion Aircraft Corp. Rochester, WI Page 1 of 5

American Champion Aircraft Corp. Rochester, WI Page 1 of 5 Service Letter: 444 Initial Revision Date: August 18, 2017 Title: American Champion Aircraft Corp. Rochester, WI 53167 Page 1 of 5 Installation of Aileron Hinge Reinforcement Models: 8KCAB serial numbers

More information

Assembly Instructions 10 X 10 Aluminum Frame Building

Assembly Instructions 10 X 10 Aluminum Frame Building Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal

More information

Metal Aircraft Landing Light Installation Instructions

Metal Aircraft Landing Light Installation Instructions Metal Aircraft Landing Light Installation Instructions This landing light kit was designed for the Thorp T-18 as a method of installing a halogen landing light in the leading edge of the outer bay of the

More information

Air Research Technology Inc. WING-X STOL Installation Guide NO: for kit(s) #R-1582,1582-1,1582-1CS,1582-SS

Air Research Technology Inc. WING-X STOL Installation Guide NO: for kit(s) #R-1582,1582-1,1582-1CS,1582-SS Air Research Technology Inc. WING-X STOL Installation Guide NO: 205-210 for kit(s) #R-1582,1582-1,1582-1CS,1582-SS For installation on Cessna models 205 and 210 series airplanes as per Transport Canada

More information

STANDARD CANOPY WORK REPORT B-1

STANDARD CANOPY WORK REPORT B-1 STANDARD CANOPY WORK REPORT B-1 No. Check Parts / Tools Qty _ Canopy Lock 1 [ ] 6E2-3 Canopy Hinge Block 1 2 [ ] 6E4-5 Canopy Side Frame 2 2 [ ] 6E2-1 Canopy Lock Assembly 1L + 1R 3 [ ] 6E2-4 Rear Lock

More information

SERVICE BULLETIN

SERVICE BULLETIN 14401 Keil Road NE, Aurora, Oregon, USA 97002 PHONE 503-678-6545 FAX 503-678-6560 www.vansaircraft.com info@vansaircraft.com Service Letters and Bulletins: www.vansaircraft.com/public/service.htm SERVICE

More information

HORIZONTAL STABILIZER AND ELEVATOR

HORIZONTAL STABILIZER AND ELEVATOR HORIZONTAL STABILIZER AND ELEVATOR CONSTRUCTION OF THE HORIZONTALSTABILIZER Inspect the pre-molded top and bottom horizontal tail skins. Note that each skin consists of a horizontal stabilizer skin and

More information

Rev: 01 Mar Rev: 01 Mar Empennage Assembly. F1 Assembly Manual Chapter 1

Rev: 01 Mar Rev: 01 Mar Empennage Assembly. F1 Assembly Manual Chapter 1 Technical Support: mar k@teamrocketaircraft.com Page 1 Empennage Assembly F1 Assembly Manual Chapter 1 Page 2 Technical Support: mark@teamrocketaircraft.com F-1 Construction Methods FIRST EDITION JUNE

More information

Drilling Your Wings to Your Fuselage

Drilling Your Wings to Your Fuselage Drilling Your Wings to Your Fuselage The purpose of this write up is to give some further guidance on how to get the best results drilling your wing spar attach holes to the upper fuselage attach fittings.

More information

83199 Grain Tank Auger Liner John Deere 9650 STS, 9750 STS, & 9570 STS Installation Instructions

83199 Grain Tank Auger Liner John Deere 9650 STS, 9750 STS, & 9570 STS Installation Instructions Kit Contents: #22424 Poly Panel 16 Wide X 8ft. White (Qty. 1) #22425 Poly Panel 14 Wide X 8ft. White (Qty. 1) #22147 SST Strap 2 X 24 X 15 Bend (Qty. 16) #22440 Shim White 2 X 6 X 1/8 (Qty. 6) #41596 Grain

More information

4. Instrument Panel Support

4. Instrument Panel Support Instrument Panel installation for serial numbers 52 to current Section Objective: Installation of the instrument panel pod. Installation of all the accessories including; vents gas strut supports, engine

More information

Air Research Technology Inc. WING-X STOL Installation Guide NO: 172 for kit(s) #R-1582,1582-1,1582-1CS,1582-SS

Air Research Technology Inc. WING-X STOL Installation Guide NO: 172 for kit(s) #R-1582,1582-1,1582-1CS,1582-SS Air Research Technology Inc. WING-X STOL Installation Guide NO: 172 for kit(s) #R-1582,1582-1,1582-1CS,1582-SS For installation on all Cessna models 170, 172, and 175 series airplanes as per Transport

More information

SE5a Wing Panels rev 1.0

SE5a Wing Panels rev 1.0 SE5a Wing Panels rev 1.0 The top and bottom wings are different. They might look the same but the bottom wing has one less rib and some rib spacing difference. This is due to where the wooden interplane

More information

Rev: 01 Sept Technical Support: 01 Sept Evo Wing Assembly. F1 Evo Assembly Manual Chapter 6

Rev: 01 Sept Technical Support: 01 Sept Evo Wing Assembly. F1 Evo Assembly Manual Chapter 6 Page 1 01 Sept 2007 Evo Wing Assembly F1 Evo Assembly Manual Chapter 6 Page 2 Technical Support: mark@teamrocketaircraft.com F-1 Evo Suggested Wing Assembly Methods FIRST EDITION DECEMBER 2004 01 SEPT

More information

SZD-10 bis CZAPLA ASSEMBLY MANUAL IN PICTURES

SZD-10 bis CZAPLA ASSEMBLY MANUAL IN PICTURES 1 RUDDER Plan and parts: 2 Assembly steps: Photo above: glue together rudder spar, ribs and trailing edge. Clamp spar to a flat surface (chipboard on the photo) and make sure the straight aligment of the

More information

STC GROUP LLC 480 RUDDIMAN DRIVE MUSKEGON, MICHIGAN REPORT NO: G REV E TRIO AUTO PILOT INSTALLATION INSTRUCTIONS

STC GROUP LLC 480 RUDDIMAN DRIVE MUSKEGON, MICHIGAN REPORT NO: G REV E TRIO AUTO PILOT INSTALLATION INSTRUCTIONS STC GROUP LLC 480 RUDDIMAN DRIVE MUSKEGON, MICHIGAN 49445 REPORT NO: G-1006-51 REV E TRIO AUTO PILOT INSTALLATION INSTRUCTIONS CESSNA MODEL 182 WITH PREVIOUS CESSNA EQUIPPED AUTO PILOT DATE: Original Issue

More information

Ford Ranger / Bronco II Set Part # Rev B 5-04

Ford Ranger / Bronco II Set Part # Rev B 5-04 Ford Ranger / Bronco II Set Part # 21008 Rev B 5-04 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure proper fit).

More information

Pre-Paint>Fuselage>Empennage>Fit elevator. Objectives of this task: Materials required: Prepare the horizontal stabiliser and the elevator

Pre-Paint>Fuselage>Empennage>Fit elevator. Objectives of this task: Materials required: Prepare the horizontal stabiliser and the elevator Pre-Paint>Fuselage>Empennage>Fit elevator Objectives of this task: To fit the elevator to the horizontal stabiliser, to fit the trim tabs to the elevator and the end caps to the elevator and the horizontal

More information

7. Ailerons. Overview.

7. Ailerons. Overview. 7. Ailerons Overview. The ailerons are made in much the same way as the rudder. The only difference being that the ends are not rounded but have close-out ribs instead and the aileron cores are supplied

More information

INSTALLATION INSTRUCTIONS FOR EXHAUST CUFF MODIFICATION

INSTALLATION INSTRUCTIONS FOR EXHAUST CUFF MODIFICATION INSTALLATION INSTRUCTIONS FOR EXHAUST CUFF MODIFICATION Document # PCA1001-21 Revision LTR: NC Date: 09/15/08 1 Notes: 1. The Exhaust Cuff comes assembled with the three attachment brackets secured. We

More information

Important Note. Tools Required: Welder capable of fully welding 10 GA.135 steel

Important Note. Tools Required: Welder capable of fully welding 10 GA.135 steel INSTALLATION INSTRUCTIONS Frame Reinforcement Kit 11100 (Patent Pending) 1968-72 GM A-Body Coupe/Sedan Read Instructions FULLY before starting Installation Important Note Installation of this kit requires

More information

SD3-60 STRUCTURAL REPAIR MANUAL AND TABS - STRUCTURAL IDENTIFICATION

SD3-60 STRUCTURAL REPAIR MANUAL AND TABS - STRUCTURAL IDENTIFICATION SRM 7.0.0.0ELEVATORS AND TABS - STRUCTURAL IDENTIFICATION 1. General This section identifies the skin panels and structural components of the elevators, trim tabs and spring tabs. Details are given of:

More information

CHEVY 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4434

CHEVY 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4434 CHEVY 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4434 Installation Instructions SPECIFICATIONS Fits 1999-2010 Chevy 2500 & 3500 Short Bed Mounts to B&W gooseneck part #1067 Hitch

More information

STC GROUP LLC Page Ruddiman Drive PA-28 & PA-32 Trio Pro Pilot Installation Instructions North Muskegon, Michigan 49445

STC GROUP LLC Page Ruddiman Drive PA-28 & PA-32 Trio Pro Pilot Installation Instructions North Muskegon, Michigan 49445 STC GROUP LLC Page 1 STC GROUP LLC 480 RUDDIMAN DRIVE MUSKEGON, MICHIGAN 49445 DOCUMENT NO: 1028001 REVISION D TRIO PRO PILOT INSTALLATION INSTRUCTIONS PIPER AIRCRAFT CORPORATION PA-28 AND PA-32 DATE:

More information

Art Rack Assembly Instructions:

Art Rack Assembly Instructions: Art Rack Assembly Instructions: ** PIECES ARE POWDER COATED Do not lay pieces on top of each other or on a hard, rough surface if possible. All bolts will pass from outside towards inside of the cage.

More information

Zodiac CH 601 XL drawing revision log, updates included in 4 th Edition, January 1, 2008.

Zodiac CH 601 XL drawing revision log, updates included in 4 th Edition, January 1, 2008. Zodiac CH 601 XL drawing revision log, updates included in 4 th Edition, January 1, 2008. 6-X-0 6-X-1 6-T-0 6-T-1 6-T-2 6-T-3 6-T-4 6-T-5 6-T-6 6-W-0 6-W-00 6-W-1 6-W-2 6-W-3 6-W-4 6-W-5 6-W-6 01/08 DRAWING

More information

Assembly Instructions 10 X 10 Aluminum Roof Support

Assembly Instructions 10 X 10 Aluminum Roof Support Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1

More information

Important Note. Tools Required: Welder capable of fully welding 10 GA.135 steel

Important Note. Tools Required: Welder capable of fully welding 10 GA.135 steel INSTALLATION INSTRUCTIONS Frame Reinforcement Kit 11102 (Patent Pending) 1964-67 GM A-Body Coupe/2dr Sedan Read Instructions FULLY before starting Installation Important Note Installation of this kit requires

More information

SD3-60 STRUCTURAL REPAIR MANUAL - STRUCTURAL IDENTIFICATION

SD3-60 STRUCTURAL REPAIR MANUAL - STRUCTURAL IDENTIFICATION SRM 2.0.0.0CENTRE WING - STRUCTURAL IDENTIFICATION 1. General This subject identifies the structural components and skin plating of the centre wing. Details are given of specific location, material specifications

More information

Set Part # Rev

Set Part # Rev Set Part # 21007 Rev-3 06-06-11 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to

More information

Jabiru Aircraft. Fit Ailerons

Jabiru Aircraft. Fit Ailerons Fit Ailerons Reference: Drawings 2033091 and 20210K1 Photos Parts Required: 2021091 Wing LS 202209N Wing RS 2027092 Aileron LS 202809N Aileron RS 2036034 Aileron reinforcement Left 203703N Aileron Reinforcement

More information

1881 Airport Road, Mexico Memorial Airport, Mexico, Missouri USA Tel: Fax:

1881 Airport Road, Mexico Memorial Airport, Mexico, Missouri USA Tel: Fax: www.zenithair.com 1881 Airport Road, Mexico Memorial Airport, Mexico, Missouri 65265 USA Tel: 5735819000 Fax: 5735810011 Zenith CH 750 Cruzer builder and owner: 4 February, 2016 We're pleased to release

More information

FREEDOM 2 PORTABLE RESTROOM ASSEMBLY INSTRUCTION

FREEDOM 2 PORTABLE RESTROOM ASSEMBLY INSTRUCTION FREEDOM 2 PORTABLE RESTROOM ASSEMBLY INSTRUCTION 2530 Xenium Lane North, Minneapolis, MN 55441 Telephone: 763-553-1900 Fax: 763-553-1905 800-328-3332 / www.satelliteindustries.com PN 14579/REV. X 9/06

More information

P/N D STOL CH 701 FUEL SENDER INSTALLATION KIT P/N D

P/N D STOL CH 701 FUEL SENDER INSTALLATION KIT P/N D P/N 221-012D Float type fuel sender unit in supplier box Use VDO Fuel Level Gauge 70-10 Ohms, turn to last page this section. FUEL SENDER INSTALLATION KIT P/N 226-451D IMPORTANT: Do not adjust or modify

More information

EXPRESS ASSEMBLY MANUAL SECTION 3 F5-RG/FT WING ASSEMBLY. Procedure 3.155A WING CLOSE-OUT PROCEDURES

EXPRESS ASSEMBLY MANUAL SECTION 3 F5-RG/FT WING ASSEMBLY. Procedure 3.155A WING CLOSE-OUT PROCEDURES Procedure 3.155A WING CLOSE-OUT PROCEDURES In this procedure The lower wing skin will be bonded to the upper wing For this procedure, the following parts will be required: Part Number Description Qty 111-11-060-01

More information

2000 Tomlynn Street P.O. Box 6861 Richmond, Virginia / FAX 804/ Service Bulletin

2000 Tomlynn Street P.O. Box 6861 Richmond, Virginia / FAX 804/ Service Bulletin Sequoia Aircraft Corporation 2000 Tomlynn Street P.O. Box 6861 Richmond, Virginia 23230 804/353-1713 FAX 804/359-2618 Service Bulletin Service Bulletin No. 93-1 Subject: Flap Flutter Date: June 24, 1993

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS TOOLS REQUIRED Rechargeable, variable speed drill 3/8 diameter drill bit 3 Robertson bits #0, #1 and #2 Slot screwdriver Non marring hammer with 1 head Level Caulk or sealant

More information