FrameSaver Jamb Bottom Replacement Instructions
|
|
- Mercy Cunningham
- 5 years ago
- Views:
Transcription
1 FrameSaver Jamb Bottom Replacement Instructions 8817 West Market Street Colfax, NC Utility Knife Straight Edge Circular Saw Reciprocating Saw Miter Saw Shims Screws Window and Door Insulating Foam Sealant TOOLS NEEDED: Product Reference Guide Exterior Grade Wood Filler or Putty Flashing Tape 2" Brad Nails Putty Knife High Quality Exterior Silicone Caulk Weatherstrip (optional) Simple Solution Corner Pad (optional) Weatherstrip Jamb Corner Pad Brickmould Door Sill Rev. Date: Endura Products, Inc. 1 of 5
2 STEP 1: PREPARE THE AREA a. Remove the weatherstrip from the jamb. Remove the corner pad, if present. b. Pry off the brickmould by cutting the caulk line with a utility knife on both sides of the brickmould along its entire length. STEP 2: REMOVE THE DAMAGED AREA 90 < 8" a. Mark a horizontal line on the jamb, no more than 8" from the bottom of the sill. If this is on the hinge side, ensure the mark is made several inches below load bearing area. b. Use a circular saw to cut into the jamb at the mark made. Set the blade depth to 1-1/4" and make several straight-in plunge cuts along the pencil line. c. Cut behind the jamb to cut into any fasteners that may be securing the jamb to the stud. d. Dislodge the jamb piece to remove. Scrape and vacuum out any wood rot remaining in the resulting gap. 2 of 5
3 STEP 3: SIZE THE NEW JAMB BOTTOM X X Measure the height at the end (Y 1 ) a. Determine the height of the jamb needed to be replaced. Measure and cut the end of the new door jamb using a miter saw for precision cuts. b. Measure the height of the sill on the exterior. Measure the height of the sill here (Y 2 ) Y 2 Y 1 c. Determine the height of the sill along the side, right next to the sill cap. d. Mark those two points on the thicker side of the jamb. Y 1 on the exterior edge and Y 2 on the edge closest to the weatherstrip slot. Top View Cut through the jamb to be flush with rabbet Rabbet Dado Cut e. Connect the points created in Step 3d and cut along that line to create the dado. Cut into the jamb ONLY until you reach the plane of the rabbet. 3 of 5
4 STEP 4: INSTALL AND SEAL THE NEW JAMB BOTTOM a. Place the sized jamb into the space to ensure it fits properly. Using a pencil, outline the sill against the jamb. b. Remove the cut jamb piece from the space and fill in the outlined "sill space" with high quality exterior silicone as shown above. Top View Stud Shims NOTE: The number of fasteners will vary depending on the length of the replaced piece. Jamb! The installation requires a minimum of two sets of shims: one on the bottom to compress it against the sill and another close to the joint with the existing frame. c. Slide the jamb piece with the caulk applied into the cut space. Use at least two sets of shims to ensure the jamb piece is aligned with the plane of the existing jamb. Be sure to put the shims in opposite! directions to ensure the jamb piece does not rotate. Sand down this seam d. Once the jamb piece is secured against the sill, fasten it into the frame with screws. Cut any extended shims to be flush with the jamb. Fill gaps behind new jamb piece e. Fill the seam with exterior grade wood filler or putty. Sand down the seam between the existing jamb and new jamb piece to blend them. f. Using a Window and Door Insulating Foam Sealant, fill any gaps behind the new jamb. 4 of 5
5 STEP 5: REINSTALL THE BRICKMOULD Old Brickmould Z 1 New Brickmould 45 Z 1 a. Cut a long strip of flashing tape to cover the gap between the door jamb and exterior sheeting of the house. b. Measure the outside edge of the old brickmould (Z 1 ). Mark the new brickmould at Z 1 and cut it down at a 45 angle as shown above. 8" 8" c. Fasten the brickmould using 2" Brad Nails, about 8" apart. Expect some expanding foam squeeze-out! in the bottom corner. Use a putty knife to wipe off the excess foam while it's uncured. d. Caulk the seam between the sill and jamb and around the brickmould using a high quality exterior silicone. STEP 6: REINSTALL THE WEATHERSEALING COMPONENTS a. Once the area has been repainted and dries, install new weatherstripping along the full length of the jamb. b. Install a new corner pad on the bottom of the jamb, right above the sill cap. 5 of 5
I n s t a l l a t i o n I n s t r u c t i o n s
HInged PAtio Door Systems I n s t a l l a t i o n I n s t r u c t i o n s IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation.
More informationEndura All-Aluminum Z-Articulating Cap Sill Retrofit Kit for French Doors
Endura All-Aluminum Z-Articulating Cap Sill Retrofit Kit for French Doors Installation Instructions Before You Begin: This retrofit kit is designed for the Endura Z-Series All- Aluminum sill. Please ensure
More informationWindow with Nail fin (New construction)
Window with Nail fin (New construction) Disclaimer: Improper installation and care may void warranty. These instructions are a basic/general recommendation for installation, but may not be utilized in
More informationFold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE
Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE This instruction guide provides the minimum recommended procedures to correctly prepare the rough opening, install a fold-a-way patio door unit and apply
More informationChapter 9. Windows and Exterior Doors
Chapter 9. Windows and Exterior Doors 9.1 INSTALLING WINDOWS 9.2 INSTALLING EXTERIOR HOUSE DOORS 9.3 INSTALLING SHED DOOR 9.4 INSTALLING BASEMENT EGRESS COMPONENTS Tools needed by volunteers: Hammer Nail
More informationChapter 9. Windows and Exterior Doors
Chapter 9. Windows and Exterior Doors 9.1 INSTALLING WINDOWS 9.2 INSTALLING EXTERIOR HOUSE DOORS 9.3 INSTALLING SHED DOOR 9.4 INSTALLING EGRESS COMPONENTS Tools needed by volunteers: Hammer Nail apron
More informationTRIM & DOORS. Note Interior work demands more precision than framing - be exact in your measurements! Outfitting the interior.
104 TRIM & DOORS Outfitting the interior Table of Contents Interior Doors... 105 Single... 106 Double... 108 Paint Prep... 110 Caulking & Spackling... 112 Baseboard... 113 Window Sills... 115 Nail Gun
More informationPocket Door Installation Instructions
Installation Instructions Before getting started: Read instructions thoroughly. Be sure that you have the necessary tools and materials before starting the installation. Consult your local building code
More informationAluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement
Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement 1 Aluminum Clad Wood Window 1/2 Reinforced Field Mulling and Stacking Supplement The following instructions are a supplement
More informationInstallation Instructions for Siding
Smart-Shingle TM System "The new smart way to install cedar shingles." - This Old House Installation Instructions for Siding V3.2 INSTALLATION GUIDE MARKS Shingle-Strip 0 1 2 3 4 5 6 7 8 9 10 11 12 13
More informationTape Measure Metal Clippers Screw Bit Set With Extensions
IMPORTANT: Read through instructions thoroughly before beginning to replace any damaged material. Minor damage can be fixed with a fiberglass repair kit and color matched paint. Tools Required Tape Measure
More informationInstallation Instruction 3-D Model 3D 03/01/17. 0 Flush Siding Horizontal System N/C WPS, Inc.
I B D L K C E G M F A H J Installation Instruction 3-D Model 3D 03/01/17 Detail: System Type: Scale: Drawn By: 0 Flush Siding Horizontal System N/C WPS, Inc. Wall Panel System, Inc. 15/16" 1 1/4" Bottom
More informationTHERMO-FIT REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS (BRICKMOULD / NO NAILING FLANGE)
THERMO-FIT REPLACEMENT WINDOW INSTALLATION INSTRUCTIONS (BRICKMOULD / NO NAILING FLANGE) fig.3 Casement, Awning, Fixed Casement, Direct-Set, Double-Hung, Single-Hung & Horizontal Slider Windows Materials
More informationSliding Glass Door Assembly and Installation Guide
Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all
More informationNon-Reinforced Joining Guide (2-Way Horizontal and Vertical Joining) for Andersen 200 Series Tilt-Wash Double-Hung and Transom Windows
(2-Way Horizontal and Vertical Joining) for Andersen 200 Series Tilt-Wash Double-Hung and Transom Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly,
More informationUNIT 5: EXTERIOR DOORS AND WINDOWS
KEY CONCEPTS 1. Identify tools needed for exterior door and window installation 2. Last step to weather proofing the home 3. Steps to installing exterior doors and windows 4. Maintenance and safety of
More informationINSTALLATION GUIDE WOOD PIVOTING CIRCLE/ OVAL
WOOD PIVOTING CIRCLE/ OVAL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to these instructions will VOID any
More informationSITE 5 Repair and Replacement
SITE 5 Repairing Therma-Tru Door Slabs... 5.3 Sidelite Slab... 5.6 Mull Post... 5.13 Weatherstrip... 5.21 Adjustable Sill Threshold... 5.22 Basic Fixed Sill Vinyl Threshold... 5.24 Doorlite Glass and Frame...
More informationWOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW
WOOD OUT SWING AWNING, CASEMENT, & HOPPER WINDOW INSTALLATION GUIDE READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TOOLS REQUIRED Rechargeable, variable speed drill 3/8 diameter drill bit 3 Robertson bits #0, #1 and #2 Slot screwdriver Non marring hammer with 1 head Level Caulk or sealant
More informationChapter 18. Interior Doors
Chapter 18. Interior Doors 18.1 SWINGING DOORS 18.2 SLIDING DOORS 18.3 BIFOLD DOORS Tools needed by volunteers: Hammer Nail apron Tape measure Square Pencil Tools and equipment needed: Extension cords
More informationMira Premium Series Bi-Parting French Sliding Patio Door Installation Instructions
PREMIUM SERIES W I N D O W S Mira Premium Series Bi-Parting French Sliding Recommended Tools & Accessories Tape Measure Level (3 or longer) Hammer Power Screwdriver Load bearing Shims Flashing (recommended)
More information4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside.
Effective Date: 10/1/2017 Tools Needed Kit Contents Hardware Kit Safety Glasses Cordless drill Phillips screw bit Two-step drill bit (3/8-1/8 ) utility knife Interior Mullion Exterior Mullion Cover clamps
More informationRead guide from beginning to end before starting installation. Read and follow all warnings and cautions during unit installation.
Installation Guide for Andersen Clad Outswing Folding Doors with Track-In-Floor Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection
More informationINSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD CASEMENT & AWNING WINDOW VENTANA DE DOS HOJAS CON REVESTIMIENTO
2008 Pella Corporation Part Number: 801P0101 INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD CASEMENT & AWNING WINDOW VENTANA DE DOS HOJAS CON REVESTIMIENTO Corner Corner Top Fin Corner
More informationBlock Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5.
Effective Date: 10/1/17 Tools Needed Kit Contents Safety Glasses Cordless Drill Phillips Screw Bit Two-step Drill Bit (3/8-1/8 ) Utility Knife Interior Mullion Exterior Mullion Cover Hardware Kit Clamps
More informationFOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL
FOLDING DOOR - FOR FACTORY ASSEMBLED JAMBS WITH APPLIED SILL READ SPECIFIC INSTALLATION INSTRUCTIONS COMPLETELY BEFORE STARTING ANY INSTALLATION Failure to install and maintain our product according to
More informationRetractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors)
Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors) IMPORTANT: Please read before you begin. Table of Contents
More informationSteel Reinforced Joining Thank you for choosing Andersen. Please leave this guide with building owner.
Steel Reinforced Joining (Horizontal/Vertical) for Andersen 400 Series Woodwright & Tilt-Wash Double-Hung, Picture, and Transom Windows and 400 Series Double-Hung Half Circle and Flexiframe Specialty Windows
More informationINSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS.
INSTALLATION INSTRUCTIONS FOR FORGENT SLIDING PATIO DOORS RECOMMENDATIONS FOR COMMON INSTALLATION OF SLIDING PATIO DOORS. Installer: DO NOT DISCARD Please leave the Installation Guide with the home owner
More informationHeavy Wall Applied Stop Tube Frame and Door Installation
INSTALLATION INSTRUCTIONS Heavy Wall Applied Stop Tube Frame and Door Installation Read all instructions before beginning installation. These instructions are provided to help prevent installation problems
More informationHR175 Sash Replacement Kit Installation Instructions
HR175 Sash Replacement Kit Installation Instructions IMPORTANT: Please read before you begin. Weather Shield HR175 Sash Replacement Kits Important: Thoroughly read and follow these instructions, failure
More informationHow To Install Windows: Nail-Fin Application
How To Install Windows: Nail-Fin Application Required Tools & Materials: Materials: 1 3/4" galvanized roofing nails. Nails must penetrate at least 1" into framing For mulled and/or DP50 or above units:
More informationEagle clad double-hung window installation instructions
Eagle clad double-hung window installation instructions These instructions are for typical installation in new typical wood frame wall construction. These instructions and methods are not intended for
More informationRead guide from beginning to end before starting installation. Read and follow all warnings and cautions during unit installation.
Installation Guide for Andersen Wood Outswing Folding Doors with Track-In-Floor Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection
More informationSash Replacement Guide for Andersen 400 Series Tilt-Wash Transom Windows
for Andersen 400 Series Tilt-Wash Transom Windows Read all instructions carefully before attempting this procedure. If you have any questions about your ability to complete this procedure, call Andersen
More informationINSTALLATION INSTRUCTION SINGLE PANEL, SINGLE PANEL WITH SIDELIGHT COMBINATION AND 20 MINUTE FIRE RATED WOOD FRAME ENTRY DOOR
2011 Pella Corporation Part Number: 818T0101 INSTALLATION INSTRUCTION SINGLE PANEL, SINGLE PANEL WITH SIDELIGHT COMBINATION AND 20 MINUTE FIRE RATED WOOD FRAME ENTRY DOOR Installation Instructions for
More informationPicture Window and Welded Dead-Lite (Exterior) Tools: (Not Provided by Manufacturer) Fig Supplies: (Not Provided by Manufacturer) Fig.
Picture Window and Welded Dead-Lite (Exterior) Tools: (Not Provided by Manufacturer) Tape Measure Utility Knife Fig. 0-1 Drill Level Putty Knife Pry bar Square Foam Gun (Optional) Caulk Gun Hammer Safety
More informationGarage Door Frame Retro-Fit Clad Installation Instructions
Garage Door Frame Retro-Fit Clad Installation Instructions Patent # US 7,111,433 B2, CA 2,415,545, Other Patents Pending Tools required Screw driver (screw gun), hammer, pry bar, tape measure, compound
More informationInSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled
InSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled Measuring Tape Pencil Shims Drill & Drill bits: 6", 8", 5 6", 7 6" Tools & materials You Will need: Square Hammer or Mallet Level Stiff Putty
More informationT he Double-Hung Replacement System replaces the sash and balance system of an older double-hung window. The
Double-Hung Replacement System Installation The Pozzi Collection PID001 (12/03) T he Double-Hung Replacement System replaces the sash and balance system of an older double-hung window. The frame of the
More informationINSTALLATION INSTRUCTION FOR WOOD DOUBLE-HUNG AND CASEMENT WINDOWS USING WOOD BRICKMOULD OR FLAT CASING
2009 Pella Corporation Part Number: 80DZ0101 INSTALLATION INSTRUCTION FOR WOOD DOUBLE-HUNG AND CASEMENT WINDOWS USING WOOD BRICKMOULD OR FLAT CASING Brickmould/Flat Casing Aluminum Head Flashing Corner
More informationINSTALLATION INSTRUCTIONS for Custom and Premium Pocket Windows (JII022) IMPORTANT INFORMATION AND GLOSSARY SAFETY AND HANDLING
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for pocket (replacement) double-hung, casement, awning, picture or transom windows, designed to
More informationIMPORTANT: Please read completely before you begin.
Standardized Window Installation Instructions For Maintaining Design Pressure Ratings For Aluminum or Vinyl Clad & All-Vinyl Window Units With Nailing Fin Structure With Weather Resistant Barrier Applied
More informationInstallation of Fiberglass Windows
Installation of Fiberglass Windows Before you begin please read and understand these installation instructions. The following installation instructions are recommended by Norwood and failure to follow
More informationAtrium Patio Door Field Service Manual
Atrium Patio Door Field Service Manual December 2005 Table of contents Service Agreement Pg 2 Release Agreement Pg 5 Inspection form Pg 6 Warranty Pg 8 Replacing swing panel Pg 12 Replacing sliding panel
More informationWINDOW INSTALLATION GUIDE
WINDOW INSTALLATION GUIDE SAWDAC is not responsible for or liable for any use or misuse of the information contained in this window installation guide. Window Installation Guide This guide provides basic
More informationPicture Window Rough Opening Installation with Sheathing Intact with Brickmould Tools: (Not supplied by manufacturer) Fig. 0-1
Picture Window Rough Opening Installation with Sheathing Intact with Brickmould Tools: (Not supplied by manufacturer) Tape Measure Drill Level Putty Knife Square Foam Gun Utility Knife Caulk Gun Hammer
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BUILDERS CHOICE FRAMED Shower Height Swing Door Model: L533 Rev. 09.03.13 MAINTENANCE: Two primary materials are used to manufacture your new Aquatic enclosure; tempered glass
More informationInstallation Instructions Palladium Wall Panels - Demountable Factory Finished Edges and Field Cut Edges
Please read all instructions before installing Palladium Wall Panel System. 1. Before installation: a. Acclimate Palladium Panels, reveals, adhesives and wall substrates to room temperature 24 hours before
More informationInstallation Guide for Architectural Wood Hinged Windows
Guide for Architectural Wood Hinged Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if the benefits
More informationMake every component count.
Make every component count. Technical Bulletin Installation Instructions ABOUT THE MATERIAL The frame and material have been thoroughly tested for strength, durability and low maintenance, offering a never
More informationTransom Joining. for Andersen Elliptical Windows over Perma-Shield Gliding Patio Door
Transom Joining for Andersen Elliptical Windows over Perma-Shield Gliding Patio Door INSTALLER: Please leave this guide with the building owner to file for future reference. Congratulations! You have just
More informationSTACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS
STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions
More informationSun Windows General Information New Construction Hinged Door Installation Instructions
A G H F H H A. Apply Weather Resistive Barrier B. Apply Bottom Flashing Tape C. Install Sill Pan End Caps & Pan D. Caulk Sides & Top Nailing Surface, Set Door, Fasten E. Apply Side Flashing Tape F. Apply
More informationNon-Reinforced Joining Guide (Horizontal/Vertical)
Non-Reinforced Joining Guide (Horizontal/Vertical) for Andersen Casement, Awning, and Picture Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation
More informationFollow instructions from foam, sealant and flashing manufacturer regarding material application and compatibility with this product.
Installation Guide for Andersen Wood Outswing Folding Doors Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place. Instructions
More informationSeries 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing)
Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration
More informationNEW CONSTRUCTION PATIO DOOR INSTALLATION INSTRUCTIONS (WITH NAILING FLANGE)
NEW CONSTRUCTION PATIO DOOR INSTALLATION INSTRUCTIONS (WITH NAILING FLANGE) Slim Line & Classic French Style Patio Doors Materials included: (2) #10 x 2-1/2" Phillips Pan head keeper s (2) 3/8" Hole plugs
More informationVINYL REPLACEMENT WINDOW INSTALLATION STANDARDS
VINYL REPLACEMENT WINDOW INSTALLATION STANDARDS BEFORE you start to remove the existing windows Place clean drop cloths in all work areas. Re-measure the opening to ensure the new window will fit. Remove
More informationVinyl Windows and Doors
Vinyl Windows and Doors Manufactured by Pella Corporation Installation Instructions for Replacement of Aluminum Sliding Doors in Hard Coat Stucco Applications. Part Number: V981555 2009 Pella Corporation
More informationBefore installation, check your local and state requirements for this type of install.
1 Remove Packaging & Inspect Your Patio Door Remove shipping materials such as corner covers or pads. 2 Inspect Rough Opening Verify that the width and height of the patio door are each 1/2" to 3/4" smaller
More informationfor Andersen Frenchwood Hinged and Outswing Patio Doors, Sidelights, and Transoms
for Andersen Frenchwood Hinged and Outswing Patio Doors, Sidelights, and Transoms Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationFrameless Inline Door With Return QCI5263
INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges
More informationDog door (in an) afternoon Give your pet the freedom to come and go whenever it wishes by installing this energy-efficient kit
Dog door (in an) afternoon Give your pet the freedom to come and go whenever it wishes by installing this energy-efficient kit Y THOMS KER PHOTOGRPHS Y NTHONY TIEULI WHEN LIFE GETS USY, it s easy to miss
More informationWINDOW REPLACEMENT INSTRUCTIONS FOR SINGLE-HUNG, DOUBLE-HUNG, CASEMENT, AWNING INTO EXISTING CASEMENT FRAME USING FRAME SCREWS
2009 Pella Corporation Part Number: 80YV0102 WINDOW REPLACEMENT INSTRUCTIONS FOR SINGLE-HUNG, DOUBLE-HUNG,, AWNING INTO EXISTING FRAME USING FRAME SCREWS These instructions were tested and developed for
More informationEffective February, 2015
Effective February, 2015 Table of Contents Ensuring System Performance 1 Components 2 Frequently Asked Questions 3 List of Tools 3 Before you Begin Preparation 3 Quality Tips 4 Cold Weather Tips 4 Cleaning
More informationInstalling your new Bevella Top. L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls)
Installing your new Bevella Top L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls) Bevella RTI Countertops are engineered and manufactured to the highest quality standards, built
More informationINSTALLATION INSTRUCTION FOR CLAD BOW WINDOWS WITHOUT HEAD AND SEAT BOARD
2008 Pella Corporation Part Number: 80KG0101 INSTALLATION INSTRUCTION FOR CLAD BOW WINDOWS WITHOUT HEAD AND SEAT BOARD Note: These instructions may be used for all Pella Bow windows that do not have a
More informationRevision Date: April 01, Paramount Enclosure
Paramount Enclosure www.urbanindustries.com 15 Urban Industries, Inc. 2008 Tools The following tools are recommended for the installation of the Paramount Aluminum Enclosure and roof. 1 2 Level 1 4 Level
More informationCabinetry Installation
Cabinetry Installation Easy to follow step-by-step kitchen cabinet installation Hammer Pry bar Screwdriver Phillips Flathead Level TOOL AND MATERIAL LIST Tape measure Pencil Straight edge Drill 3/16" drill
More informationREMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.
Vinyl Windows and Doors Manufactured by Pella Corporation WINDOW REPLACEMENT INSTRUCTIONS FOR DOUBLE-HUNG VENT REPLACEMENT WINDOWS INTO EXISTING DOUBLE-HUNG FRAME USING FRAME SCREWS FROM THE EXTERIOR Part
More informationSteel Reinforced Joining Guide (Horizontal / Vertical)
(Horizontal / Vertical) for Andersen Patio Door and/or Elliptical Top Window Combinations Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation
More informationEffective April 1, 2013
Effective April 1, 2013 Table of Contents Ensuring System Performance 1 Components 2 Frequently Asked Questions 3 List of Tools 3 Before you Begin Preparation 3 Quality Tips 4 Cold Weather Tips 4 Cleaning
More informationINTERIOR. Checkrail. Flashing tape
Pella Corporation 2007 Part Number: 808F0100 INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR PELLA PRECISION FIT DOUBLE-HUNG VENT WINDOW PARA LA VENTANA DE GUILLOTINA CON HOJA PRACTICABLE PRECISION
More informationVinyl Windows and Doors
Vinyl Windows and Doors Part Number: V983571 2011 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION 350 SERIES WINDOW INTO EXISTING WOOD FRAME WINDOW Lea las instrucciones en español
More informationAcoustical Surfaces, Inc.
RECEIVING 1. Immediately inspect shipment for damage during transit, for example: damage caused by fork lifts, stacking, water stains etc. and disclose to delivery driver prior to signing for receipt.
More informationTherma-Tru Fiber-Classic and Smooth-Star Sliding Patio Door System
PATIODOORSYSTEMS Therma-Tru Fiber-Classic and Smooth-Star Sliding Patio Door System Quad Unit Assembly & Installation Read all instructions before starting. The applicable standards for these products
More informationWood Hinged Patio Door Installation Instructions
Wood Hinged Patio Door Installation Instructions #1029970 / 1029971 / 1182557 (12/05) Rev 4 IMPORTANT: Please read before you begin installation. Wood Hinged Patio Door Door Installation Instructions IMPORTANT:
More informationInstallatIon InstructIons for 2-lIte PatIo Door unassembled
InstallatIon InstructIons for -lite PatIo Door unassembled tools & materials You will need: Measuring Tape Pencil Shims Drill & Drill bits: 6", 8", 5 6", 7 6" Utility Knife High-Performance Premium Silicone
More information2. Skid should contain the following: A door & jamb B casing C seal cover kit & D extension jamb set (if ordered), E hardware box.
RECEIVING 1. Immediately inspect shipment for damage during transit, for example: damage caused by fork lifts, stacking, water stains etc. and disclose to delivery driver prior to signing for receipt.
More informationMach Wall Installation Instructions
Mach Wall Installation Instructions Planning the Job Since Mach Wall is an innovative product that accomplishes 3 tasks at the same time (frame, insulate and drywall) and it replaces traditional framing,
More informationFrameless Fixed Panel Slider
INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need
More informationInstallation Guide for Andersen Architectural Clad Inswing Entry and Patio Doors
Installation Guide for Andersen Architectural Clad Inswing Entry and Patio Doors Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationInstallation Guide for Andersen Frenchwood Patio Door Sidelights and Transoms
for Andersen Frenchwood Patio Door Sidelights and Transoms Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance are essential if
More informationFrameless Inline Door QCI5248
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5248 FRAMELESS PANEL / DOOR / PANEL QCI5248 REV. 0 Page 1 Certified 06/16/2016 Parts List with glass to glass hinges *Quantities may vary. **Support Bar
More informationFrameless Inline Door QCI5254
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5254 FRAMELESS DOOR / PANEL QCI5254 REV. 0 Page 1 Cer fied 06/16/2016 Parts List with wall mount hinges *Quanes may vary QCI5254 REV. 0 Page 2 Cer fied
More informationSide Light Frame Pack Assembly Instructions
Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow the step by step guide. IDENTIFY THE PACK CONTENTS
More informationChapter 19. Interior Finish Work
Chapter 19. Interior Finish Work 19.1 INSTALLING FLOOR TRIM 19.2 INSTALLING CLOSET SHELVES AND POLES 19.3 INSTALLING BATHROOM ACCESSORIES 19.4 HANGING MINI-BLINDS 19.5 INSTALLING APPLIANCES 19.6 INSTALLING
More informationInstall Windsor Corners
Install Windsor Corners Tools and Supplies You'll Need 1. Exterior Grade Screws use screws that are long enough to go through the FauxPanel and firmly attach to the wall behind the FauxPanel. We recommend
More informationSash Replacement Guide for Andersen Impact Resistant Casement Windows
Replacement Guide Replacement Guide for Andersen Impact Resistant Casement Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance
More informationCasement/ Casement Picture Pocket Installation (Interior) Tools: (Not Provided by Manufacturer) Fig Supplies: (Not Provided by Manufacturer)
Casement/ Casement Picture Pocket Installation (Interior) Tools: (Not Provided by Manufacturer) Tape Measure Utility Knife Fig. 0-1 Drill Level Putty Knife Pry bar Square Caulk Gun Hammer Safety Glasses
More informationULTRA WINDOW & DOOR EXPANDERS AND RECEIVERS INSTALLATION INSTRUCTIONS
ULTRA WINDOW & DOOR S AND RECEIVERS INSTALLATION INSTRUCTIONS! CAUTION: *REMEMBER SAFETY FIRST* Proper Eye and! Hearing Protection must always be worn during installation of all window and door products.
More informationSide Light Frame Pack Assembly Instructions
Side Light Frame Pack Assembly Instructions Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow
More informationfor Andersen 400 Series Woodwright Transom over 400 Series Woodwright Double-Hung or 400 Series Woodwright Picture Window
for Andersen 400 Series Woodwright Transom over 400 Series Woodwright Double-Hung or 400 Series Woodwright Picture Window Congratulations! You have just purchased one of the many fine Andersen products.
More informationINSTALLATION INSTRUCTIONS DOUBLE-HUNG WINDOW WITH FINS
2012 Pella Corporation INSTALLATION INSTRUCTIONS DOUBLE-HUNG WINDOW WITH FINS Part Number: 802L0105 Installation Instructions for Typical Wood Frame Construction. These instructions were developed tested
More informationIntegrity Polygon and Round Top Installation and Finishing Instructions
Integrity Polygon and Round Top Installation and Finishing Instructions 08/20/2004 70852 BEFORE YOU BEGIN IMPORTANT: Read these instructions thoroughly before beginning to install your Integrity Polygon
More informationINOVO 2-LITE SLIDING PATIO DOOR
INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationInstallation Guide. for E-Series/Eagle Clad Hinged Inswing French Door
Installation Guide for E-Series/Eagle Clad Hinged Inswing French Door Thank you for choosing Andersen. Instructions are for typical, new wood-framed wall construction with weather protection in place.
More informationWall Panel Installation Instructions
Panel Installation Instructions Demolition - Common Tools Needed Reciprocating Saw Allen Wrench Set Hole Saw Set Pry Bar Dust Pan and Brush Putty Knife / Scraper Hex Bit Socket Set All Necessary Safety
More information