Installation Instructions Edge Storage System

Size: px
Start display at page:

Download "Installation Instructions Edge Storage System"

Transcription

1 Installation Instructions Edge Storage System IMPORTANT: Product is packed on pallets by individual bank. Do not mix components from different pallets together. Use the Specific Part List to determine assembly order. Unpack and sort the components according to the layout plan drawings. Match the bank letter designation on the pallet with the layout plan drawing. Visit the Edge Storage System Installation Video on Wenger s Youtube.com Channel. Note: Note: Please read and understand these instructions before starting the installation. Examine the illustrations on the following pages. If you need additional information, contact Wenger Corporation using the information below. Wenger Corporation 2012 Printed in USA 03/12 Part #253A Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota Questions? Call...USA: 800-4WENGER ( ) Worldwide:

2 contents Before Installation Overview Before You Begin Unpacking and Unloading Inportant User Information General Manufacturer Intended Use Warranty Safety Precautions Required Tools Supplied Tools Fasteners Hardware Parts List Replacement Parts List Column Identification Edge 84 Columns Edge 68 Columns Edge Robe and Uniform Columns Component Identification Overview Special Panels before installation Installation Chalk Line Optional Back Panels Wall Rail End Panels Divider Panels Shelves Column 408 Shelves Column 411 Adjustable Shelves Cleats and Splice Connectors Column 411 Options Toe Kick Panels Bottom Shelves Garment Bars Door Sets and Extrusions Top Panels Stiffeners Door Stops Top Support Bracket (Column 411 Only) Bow Hooks Gap Filler Divider Panel Identification Troubleshooting OvErviEW It is suggested that the Edge Storage System is setup in a space that is large enough to safely handle the cartons, pieces, finished columns, and dunnage. Inspect the condition of the wall and floor where the columns will be located. Determine the highest point on the floor, which will establish the leveled height of each bank. The Edge Storage System will conform with a wall that varies within 1 of straightness horizontally and 1 /2 vertically. BEfOrE YOu BEgiN IMPORTANT: The Specific Part List details the components in their order of assembly. Keep the Specific Part List for reference until the unit is completely assembled. Read the complete assembly procedure before beginning to assemble the columns. Hardware packs may contain extra fasteners that will not be required on your installation. unpacking and unloading! caution To avoid damage and injury, more than one person is required to move the packaged Edge Storage System components. installation information the order of installation is critical! Each part locks the next in place and installing in any different order may require un-assembling and repeating several steps. all parts are cut to size! (With the exception of the Optional Back Panel) If a component does not fit, make sure the correct part is being used and is being assembled correctly. If something still does not fit, re-check the measurements. 2

3 important user information general Copyright 2012 by Wenger Corporation. Printed and bound in the United States of America. All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of the publisher, unless it is for the purchaser's personal use. The information in this manual is subject to change without notice and does not represent a commitment on the part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any errors that may appear in this manual. In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this manual. The information in this document is not intended to cover all possible conditions and situations that might occur. The end user must exercise caution and common sense when assembling or installing Wenger Corporation products. If any questions or problems arise, call Wenger Corporation at 800-4WENGER ( ). manufacturer The Edge Storage System is manufactured by: Wenger Corporation 555 Park Drive Owatonna, MN WENGER ( ) intended use This product is designed to store musical instruments and garments. This product is intended for indoor use in normal ambient temperature and humidity conditions it must not be exposed to prolonged outside weather conditions. This product is intended to be assembled only as described in these instructions. WarraNtY This product is guaranteed free of defects in materials and workmanship for ten full years from date of shipment. A full warranty statement is available upon request. 3

4 safety PrecauTions Throughout this manual you may find CautiONS and WarNiNgS which are defined as follows: WarNiNg means that failure to follow the instruction may result in serious injury or death. CautiON means that failure to follow the instruction may result in serious injury or damage to property. Read all of these safety instructions before assembling and installing the Edge Storage System.! caution Make sure anyone assembling or installing the Edge Storage System has read and understands this manual.! caution Failure to comply with Warnings and Cautions in this document can result in damage to property or serious injury.! caution Always wear safety glasses and gloves when assembling or installing the Edge Storage System. required Tools Step Ladder Dead-Blow Hammer (plastic coated) Plastic Mallet Phillips Head Screwdrivers (#2 and #3) Laser Level and Laser Safety Glasses or Carpenter s Level (minimum of 4 long) Tape Measure Carpenter s Square Hammer Drill 90-degree Driver Electric Drill Wonder Bar ½ Open End Wrench Safety Glasses Gloves Jig Saw with fine tooth blade* 7-foot Straight Edge* Clamps* *Jig Saw, Straight Edge and Clamps are only required if installing the Optional Back Panel. supplied Tools Spacer Blocks Double Sided Tape** **Double Sided Tape is only supplied if installing the Optional Back Panel. 4

5 fasteners Because materials and construction of floors and walls can vary, fasteners for attaching the Edge Storage System to the structure are not provided. The installer must choose the appropriate fastener and follow the manufacturer s instructions. Fastener guidelines:! caution Inferior or improperly installed fasteners could cause sudden collapse of the Edge Storage System. Serious injury or damage may result. If the floor is wood construction, attachment should be by sheet metal or lag screws (#10 minimum). If the floor is concrete, attachment should be by ¼ concrete screw (Tapcon), ¼ drive nail or sheet metal screws (#10 minimum) into metal inserts. If the wall is wood stud-and-drywall construction, attachment should be by lag screws (¼ minimum) into every stud. If the edge of the Wall Rail ends between studs, a toggle bolt must be used within 2 of each edge. If the wall is metal stud-and-drywall construction, attachment should be by toggle bolt (snap toggle) (¼ minimum) into every stud. Toggle bolt (¼ minimum) to be used between studs. If the edge of the Wall Rail ends between studs, a toggle bolt must be used within 2 of each edge. If the wall is concrete block construction, attachment should be by concrete screws (#10 minimum) (Tapcon), ¼ drive nail or toggle bolt (¼ minimum), spaced no more than 24 apart. If the wall is poured concrete construction, attachment should be by concrete screw (Tapcon) or wedge-type concrete anchors, spaced no more than 24 apart. 5

6 hardware ParTs list #8 x 5 /8 Pan Head Screw X /4-14 x 5 /8 Sheet Metal Screw X #8-18 x 1 /2 Self-Drilling Screw X #8 x 5 /8 Truss Head Screw (painted) 147G #10-32 x 0.50 Self Tapping Screw 253A279 Single Shelf Pin X Double Shelf Pin X End Panel Shelf Pin X Top Panel Bracket (painted) 253A109 Splice Connector 253A116 Gap Filler 253A Toe Kick Bracket (unpainted) 147A Wall Rail 253A273 Cleat 253A115 Left Corner Bracket 253A113 Right Corner Bracket 253A114 6

7 hardware ParTs list (continued) The following parts are specific to individual configuration and may not be included for every column #8 x 2.50 Seismic Applications Screw X #8 x 1 7 /8 Anchor Screw X #8-15 x 1 1 /4 Truss Head Screw 146K423 Door Stop (used on 48 and 60 wide columns) 145R Stiffener (used on 48 and 60 wide Columns) 253A201 Bow Hook (used on Columns 306 and 307) X Garment Bar (used on Columns ) 145A Garment Bar (used on Columns ) 145A328 Top Support Bracket (used on Columns 411) 253A183 Front Edge Extrusion (used on Columns 411) 250A244 7

8 replacement ParTs list See the list below for parts that are shipped included already attached that may require replacement. Hanger Clip 253A104 Extrusion Clip X and #8 x 1 7 /8 Screws X Card Holder 250A353 Round Door Stop 253A200 Foot X Door Bumper X Vent X

9 column identification EdgE 84 COlumNS * * *Indicates Special Panels, see explanation on the following pages. 9

10 column identification E EdgE 68 COlumNS EdgE robe and uniform COlumNS 380* 381* 382* 383* 384* 385* *Indicates Special Panels, see explanation on the following pages. 10

11 component identification OvErviEW The various components of the Edge Storage System are shown assembled below for clarity. top panel gap filler divider panel Wall rail gap filler Optional Back panel toe kick Wire grille door Set Extrusion Bumper* Shelf toe kick Wire grille door Set Extrusion End panel *Bumper locations vary depending on column type. 11

12 component identification (continued) SpECial panels Special Panels are identified by the additional hole patterns drilled into the front edge. One hole = Column 411 Two holes = Column 408 (unless adjacent to a Column 411) Three holes = Columns Special Panels are indicated with an S on the layout plan drawing. three Holes = Columns two Holes = Column 408* One Hole = Column 411 * Column 408 Divider Panels that are shared with a Column 411 will only have one hole. 12

13 installation CHalk line CRITICAL STEP: The entire Edge Storage System is built off of the Wall Rail that is attached to the wall along a chalk line. Be sure that the chalk line starts at the left end of the bank, is level and extends the entire length of the bank. 1. Determine highest point on the floor (along both the length and width of the system) using a laser pointer or carpenter s level. 2. Measure up or 85 (depending on height of the bank) on the wall from this highest point and mark a level chalk line along the entire span of the storage system according to the layout plan drawing. Chalk line left End of Bank 85 or depth of Bank right End of Bank High point on floor length of Bank 13

14 installation OptiONal BaCk panels IMPORTANT: If back panels are not being installed, skip ahead to Wall Rail Installation. If back panels are being installed, they must be installed before all other components and cannot be added later. 1. Working from left to right, hang the back panels along the chalk line. the back panels will not reach all the way to the floor. a. Start the first panel 7 /8 in from the start of the bank (starting point of the Wall Rail). b. Attach the back panels to the wall surface using double-sided tape along the top edge. If multiple back panels are being attached, also use double-sided tape to attach the seams. Clean the back panel surfaces with isopropyl alcohol before applying tape. 2. The final back panel must end 7 /8 short of the end of the bank (ending point of the Wall Rail) and may have to be cut to the appropriate width. The total width of the back panels must be 1 3 /4 less than the overall width of the bank. Before attaching the final back panel, measure and mark the width. Lay the back panel flat and cut it with a Jig Saw using a 7 Straight Edge as a guide and Clamps. 7 /8 Chalk line Starting point of Back panels and Wall rail double- Sided tape 7 /8 End point of Back panels and Wall rail Cut Off Excess material 14

15 installation (continued) Wall rail 1. The total Wall Rail (#15) length will be 1 3 /4 less than the total length of the bank. Longer banks may require multiple Wall Rail pieces. Gather the pre-cut Wall Rail pieces to fit the individual bank according to the Specific Parts List and layout plan drawing. The individual part numbers are located on the back side of each Wall Rail piece. if starting a Wall rail next to an already installed bank or a wall, it must be started at least 1 from the end of the End panel or wall. 2. Working from left to right, start the first Wall Rail piece 7 /8 in from the starting point of the bank. Position the top edge of the Wall Rail on the chalk line and secure in place using the appropriate fasteners and method as indicated in the Fasteners section. a fastener must be within 2 of the end of each Wall rail piece. all of the pre-drilled holes in the Wall rail pieces may not need to be used or additional holes may need to be drilled. 7 /8 Wall rail 15 Without Optional Back panels With Optional Back panels! caution Wall Rail must be level before proceeding. 15

16 installation (continued) ENd panels 1. Locate the left End panel. The End Panels are identified by the outside surface having color laminate on the outside surface and Oyster laminate on the inside surface. The End Panels do not have a notch cut into the top edge and the pre-drilled holes do not go completely through. The pre-drilled hole pattern is specific to the column. 2. Locate the Hardware Kit 253A184 and attach the following cleats and brackets in the pre-drilled holes of the inside Oyster color surface of the End Panel: a. Loosely attach the Left Corner Bracket (#13) using two 1 /4-14 x 5 /8 Sheet Metal Screws (#2). The screw holes are slotted to allow for adjustment. b. Attach the Top Bracket (#10) and Toe Kick Bracket (#9) using two #8 x 5 /8 Pan Head Screws (#1) in each. Two Top Brackets are required for 40 deep columns c. Attach three Cleats (#16) as shown using one 1 /4-14 x 5 /8 Sheet Metal Screw (#2) in the slotted hole in each bracket. The Cleats should be positioned as far toward the inside of the panel as possible to avoid damage when the End Panel is hung, they will be adjusted into position later. Cleats 16 Cleat 16 Corner Bracket 13 top Bracket (painted) 10 toe kick Bracket (unpainted) 9 top Edge 16

17 installation (continued) ENd panels (CONtiNuEd) 3. Using a #3 Phillips Head Screwdriver, attach the End Panel Shelf Pins (#8) to all of the remaining open pre-drilled holes in the End Panel. End Panel Shelf Pin 8 4. Start on the left side and place the End Panel on the end of the Wall Rail. The notch at the bottom corner of the End Panel faces away from the wall and the Corner Bracket fits into the Wall Rail. The Corner Bracket rests on the outer edge of the Wall Rail and the End Panel extends beyond the Wall Rail. front detail The back surface of the End Panel should be flush with the wall surface. Adjust the slotted hole postion of the Corner Bracket if necessary. 5. When the End Panel is in position and adjusted for best fit, fully tighten the Pan Head Screws in the Corner Bracket. 17

18 installation (continued) ENd panels (CONtiNuEd) 6. Attach the Corner Bracket to the Wall Rail using one #8-18 x 1 /2 Self-Drilling Screw (#3). If installation is on a stud and drywall construction, Corner Bracket must be anchored to the wall using the appropriate fasteners as indicated in the Fasteners section. 7. Be sure that the End Panel is level vertically and square to the wall. Adjust the Cleats to meet the wall and floor and anchor the Cleats to the wall and the floor using the appropriate fasteners as indicated in the Fasteners section. 8. Finish attaching the two Floor Cleats and the Wall Cleat to the End Panel using two #8 x 5 /8 Pan Head Screws (#1) in each.! caution End Panels must be level and square to the wall before proceeding. Hole for Wall anchor #8-18 x 1 /2 Self-drilling Screw 3 #8 x 5 /8 pan Head Screw 1 Cleat location Cleat locations 9. Repeat these steps to assemble and attach the Right End Panel. to allow for adjustment, do not attach the front floor Cleat to the floor until after the toe kick panels are attached. the End panels must be parallel with each other before proceeding. Measure and confirm the space between the two End Panels according to the layout plan drawing before anchoring the other End Panel to the wall and floor. 18

19 installation (continued) divider panels 1. Working from left to right, place the Divider Panels on the Wall Rail according to the Specific Parts List and layout plan drawing. The Clip fits into the Wall Rail and the notch at the bottom corner of each Divider Panel faces away from the wall. The back surface of each Divider Panel should be flush with the wall surface. 2. Verify the correct column spacing by laying the provided sized Spacer Blocks into the columns between the Divider Panels. Clip divider panel Clip Spacer Block divider panel Spacer Blocks 19

20 installation (continued) SHElvES 1. Install Shelf Pins through the appropriate pre-drilled holes in the Divider Panels according to the shelf locations as indicated on the layout plan drawing. the divider panels are universal, some holes may not be used. Single Shelf pin 6 double Shelf pin 7 When two pre-drilled holes are next to each other, the 48 width uses the back hole. all other widths use the front hole. Use a Single Shelf Pin (#6) when shelves are at different heights in adjacent columns. Single Shelf Pins install through the opposite side of the Divider Panel for the shelf being supported. Single Shelf pin 6 Use a Double Shelf Pin (#7) when shelves will be at the same height in adjacent columns. Double Shelf Pins can install through either side of the Divider Panel. double Shelf pin 7 20

21 installation (continued) SHElvES (CONtiNuEd) See the following page for Column 408 and Column 411 Shelf installation. 2. Consult the layout plan drawing to identify the shelves by dimensions. Shelf widths will be slightly smaller than the Spacer Blocks. Attach the upper rows of Shelves according to the layout plan drawing by engaging the notches in the bottom of each Shelf with the Shelf Pins. a. Tilt the Shelf back and engage the Rear Shelf Pins. b. Tilt the Shelf down to engage the Front Shelf Pins. c. Push the Shelf back into position. For better stability, it is recommended to install the widest shelves first, working down to the narrowest shelves rather than working from left to right. Some 48 shelves may be equipped with Bumpers, proper placement is important. Column 303, the Bumper is located on the Bottom Shelf Column 304, the Bumper is located on the Top Shelf Columns , the Bumper is located on the Bottom Shelf. Consult the layout plan drawing for Column placement. do not attach the bottom row of shelves at this point. 2nd 1st 3rd Shelf pins 48 Shelf with Bumper mid-width Shelves feet locations Widest Shelves first 3. Use a 1 /2 Open End Wrench to screw the two Feet at the bottom of each Divider Panel just enough to touch the floor but not enough to lift up on the panel. Narrowest Shelves last 21

22 installation (continued) COlumN 408 SHElvES Column 408 shelves are assembled in two parts. 1. Install the larger rear shelf portion using the same procedure as the other shelves with the cut-off end towards the wall. 2. Install the smaller front shelf portion using the same procedure as the other shelves with the beveled side towards the front. do not attach the bottom row of shelves at this point. front Shelf portion rear Shelf portion Shelf pin locations Shelf pin locations Shelf pin locations COlumN 411 adjustable SHElf The shelf in Column 411 is adjustable and can be placed in any of the five heights shown by re-positioning the Shelf Pins. Shelf pin locations 22

23 installation (continued) ClEatS and SpliCE CONNECtOrS 1. Longer banks of columns may require multiple Top Panel sections to be seamed together. Reference the layout plan drawing to find any Top Panel seam locations. If there are seam locations, they will seam together over a Divider Panel. To find these seam locations, check the Specific Parts List for more than one Toe Kick. If there is more than one, additional brackets have been provided. Stage the Toe Kicks in front of the system. 2. At these Divider Panels, attach one Cleat to anchor the Divider Panel to the wall and one Cleat to anchor the Divider Panel to the floor. Each Cleat is attached to the pre-drilled holes in the Divider Panel using one 1 /4-14 x 5 /8 Sheet Metal Screw (#2) in the slotted hole and two #8 x 5 /8 Pan Head Screws (#1). Anchor each Cleat to the wall and the floor using the appropriate fasteners as indicated in the Fasteners section. for a seismic installation, attach one Wall Cleat and one floor Cleat to every divider panel. See the following page for Column 411 Cleat instructions. 3. Attach a Splice Connector (#11) into the notch at the front and top surface of each Divider Panel. Note: 40 deep columns will use two Splice Connectors in each Divider Panel. for a seismic applications, Splice Connectors will use a #8 x 2.50 Seismic application Screw (#17). location for #8 x 2.50 Seismic application Screw 17 Splice Connector 11 top panel Seam location Splice Connector 11 Cleat locations Shelves are not shown in this illustration for clarity. Splice Connector 11 Splice Connector 11 23

24 installation (continued) COlumN 411 OptiONS For both practical and cosmetic purposes on Column 411, Floor Cleats are attached to the outside surfaces of the Divider panels using the same fasteners and methods as the other columns. If space does not allow, attach the Floor Cleats to the inside surface. The Column 411 requires a Top Support Bracket (#26) to be installed in the Wall Rail. Postion the Top Support Bracket into the front facing channel of the Wall Rail at the middle of the Column 411 width as shown with the tab at the bottom. No fasteners are attached to Top Support Bracket until the Top Panels are installed. If the optional Back Panels are being installed, a Rear Stretcher is provided to conceal the gap between the Back Panel and the floor. The Rear Stretcher is attached at the back of the column and flush with the bottom of the Divider Panel using two Top Panel Brackets and #8 x 5 /8 Painted Truss Head Screws (#20). If a Column 411 is at the end of a bank, an End Extrusion (#23) must be installed on the End Panel using a #8 x 1 7 /8 Anchor Screw (#19). tab at the Bottom 411 column top Support Bracket 26 Column 411 rear Stretcher Column 411 floor Cleats positioned to Outside of divider panel Column 411 End Extrusion 23 Column 411 floor Cleat locations 24

25 installation (continued) toe kick panels use the Spacer Blocks to ensure proper spacing when attaching the toe kick panels. Be sure that the toe kick panels are tight against the panels, Brackets and Splice Connectors while attaching them. 1. Working from left to right, attach the Toe Kick Panels according to the Specific Part List and layout plan drawing. The Toe Kick Panel sections can split only centered over a Splice Connector and Divider Panel. The Toe Kick Panel sections should be positioned using a Wonder Bar to be flush with the notched surface of the panels rather than flush with the floor. The edge banding on the outside surface of the Toe Kick Panel should overhang the outside surface of the End Panel on both ends of the bank. Secure the Toe Kick Panels along the front bottom edge of the bank to the already attached Toe Kick Brackets with two #8 x 5 /8 Pan Head Screws (#1). 2. Screw in all of the Splice Connectors while keeping the Toe Kick Panels in place. 3. Anchor the Front Floor Cleat of the Right End Panel to the floor with the same fastener used to anchor the other Front Floor Cleat. toe kick Bracket Edge Banded Surface Should Overhang toe kick panel Splice Connector toe kick panel Edge Banded Surface Should Overhang 25

26 installation (continued) BOttOm SHElvES Install the Bottom Shelves using the same procedure as described for the previously installed shelves. garment BarS To install Garment Bars (#24 or #25) in Columns use two #8 x 5 /8 Pan Head Screws (#1) through the pre-drilled holes on each side. #8 x 5 /8 pan Head Screws 1 Bottom Shelves Consult the layout plan drawing and the Column Identification pages for the proper placement. garment Bar 24 or 25 26

27 installation (continued) door SEtS and ExtruSiONS CRITICAL STEP: All Shelves must be installed before proceeding! All front surfaces will be covered by either a Door Set or an Extrusion. door Extrusion 1. Hang the Door Sets and Extrusions according to the Specific Part List and layout plan drawing. For correct placement and door swing, the part number label should be at the bottom. If the bank has no doors, an Extrusion will be hung in place. Extrusion Clips It is recommended to hang the narrowest Single Door Sets first, working up to the wider Door Sets. CRITICAL STEP: Verify that the door size matches the compartment that it is covering. Also check shelf positions and latch alignment before attaching doors! Narrowest Single door Set 2. Hang the Door Sets by positioning the posts inside each Door Extrusion slightly above the Extrusion Clips located on the End Panel or Divider Panel and lowering it to engage with the Extrusion Clips. Be sure to engage every Post and Extrusion Clip.! caution Be sure that all Posts and Extrusion Clips have engaged. 3. Drive the Extrusion down into place using a Dead Blow Hammer on the top of the Extrusion. Door Sets are properly placed when the top of the Extrusion is flush with the top edge of the End Panel or Divider Panel. Verify that the door size matches the compartment it is covering. Also check shelf positions and latch alignment. Single door Set 27

28 installation (continued) door SEtS and ExtruSiONS (CONtiNuEd) 4. Hang the Extrusion Side of any Double Door Sets using the same procedure. Extrusion Side of double door Set 5. Hang the End Extrusions using the same procedure. End Extrusion 28

29 installation (continued) door SEtS and ExtruSiONS (CONtiNuEd) 6. Attach the Unattached Single Doors for any Double Door Sets to an already installed Extrusion according to the layout plan drawing. Attach the hinges for each Single Door using two #10-32 x 0.50 Self Tapping Screws (#5) through the pre-drilled holes in the Extrusion. unattached Single doors for double door Set 29

30 installation (continued) top panels CRITICAL STEP: Position all Top Panels into place before attaching them!! caution top panel label position Lifting and placing Top Panels requires two people. 1. Attach the Top Panels at the End Panels first. Refer to the Specific Part List and layout plan drawing for the correct order. For correct placement, the part number label must be on the top-rear surface. use the Spacer Blocks to ensure proper spacing when attaching the top panels 2. Slide each Top Panel section under the lip of the Wall Rail. Be sure that the edge banded sides are facing outward. The splices between the individual Top Panel sections can only occur centered over a Divider Panel and Splice Connector. Adjust the Top Panels for the best fit, with the front surfaces lining up to each other. 3. Set the overhang of the Top Panel to be 1 /8 beyond the End Panel on both the left and right side. The edge banding on the right and left sides of the Top Panel should overhang the outside surface of the End Panels. Use the Spacer Blocks to set each Divider panel. If the Top Panel does not fit or is too large/small: No parts should require any cutting. Check the dimensions of the Wall Rail and the full bank. Check that the bank matches the drawing. Verify that part numbers match the Specific Part List for that bank. 1 /8 Overhang End panel top panel 4. Force each Top Panel to be tight with the End Panels and Divider Panels while attaching. This will require two people. 5. With the Top Panels in position, attach the Top Brackets in each End Panel to the Top Panels using two #8 x 5 /8 Pan Head Screws (#1) in each. 6. Attach the Corner Brackets on the End Panels to the Top Panels using one #8 x 5 /8 Pan Head Screw (#1) in each. 7. Tighten the screws in the Splice Connectors into the Top Panel Sections. 30

31 installation (continued) StiffENEr Any 48 or 60 wide columns require that a Stiffener (#21) be installed. 1. Position the Stiffener along the underside of the Top Panel and 1 /8 back from the edge of the Front Extrusion. 2. Secure the Stiffener to the Top Panel using a #8 x 1 7 /8 Anchor Screw (#19) in each pre-drilled hole in the Stiffener. door StOp Any 48 or 60 wide columns with double doors require that Door Stops (#18) be installed. 1. Position the Door Stops along the underside of the Top Panel and 19 away from the nearest Divider or End Panel. 2. Secure the Door Stops to the Top Panel using two #8 x 5 /8 Pan Head Screws (#1) in each. top SuppOrt BraCkEt (COlumN 411 ONlY) For Column 411, secure the previously installed Top Support Bracket to the underside of the Top Panel using one #8 x 5 /8 Pan Head Screw (#1). top Support location (underside of top panel) Stiffener 21 #8 x 1 7 /8 anchor Screw 19 door Stop #8 x 5 /8 pan Head Screw 1 door Stop 18 1 /8 Between Stiffener and Extrusion Stiffener 21 Extrusion #8 x 1 7 /8 anchor Screw 19 31

32 installation (continued) BOW HOOkS To install Bow Hooks (#22) in Columns 306 and 307: 1. pre-drill four 1 /16 diameter pilot holes as recommended below. do not drill through the divider panel. 2. Secure each Bow Hook in place using two #4 x 5 /8 Brass Mounting Screws in each. #4 x 5 /8 Brass mounting Screws front Extrusion top panel Bow Hooks 22 Between 24.5 and /2 4 1 /2 gap filler Gap Fillers (#12) are self adhesive and can be attached to conceal corner gaps between Top Panels and the wall. gap fillers 12 32

33 DiviDer Panel identification The Divider Panels can be identified by the pre-drilled hole patterns. Divider Panels are drilled universal for all shelf placement unless noted as special. The following illustrations show which pre-drilled hole pattern corresponds with each assigned column number. PANELS FOR NOMINAL 20" DEEP BANKS (17.12" X 83.5" TYPICAL) COLUMNS 200 & 230 LEFT END PANEL OYSTER LAMINATE THIS SIDE OPPOSITE SIDE LAMINATED PER SELECTION HOLES DO NOT GO THRU DIVIDER OYSTER BOTH SIDES HOLES GO THRU RIGHT END PANEL OYSTER LAMINATE THIS SIDE OPPOSITE SIDE LAMINATED PER SELECTION HOLES DO NOT GO THRU 33

34 DiviDer Panel identification (continued) PANELS FOR NOMINAL 30" DEEP BANKS EXCEPT GARMENT (27.12" X 83.5" TYPICAL) COLUMNS LEFT END PANEL OYSTER LAMINATE THIS SIDE OPPOSITE SIDE LAMINATED PER SELECTION HOLES DO NOT GO THRU DIVIDER OYSTER BOTH SIDES HOLES GO THRU RIGHT END PANEL OYSTER LAMINATE THIS SIDE OPPOSITE SIDE LAMINATED PER SELECTION HOLES DO NOT GO THRU PANELS FOR NOMINAL 30" DEEP COLUMNS SPECIAL FOR GAREMENT STORAGE (27.12" X 83.5" TYPICAL) COLUMNS SMALL HOLES IDENTIFY THESE PANELS AS SPECIAL FOR GARMENT STORAGE LEFT END PANEL OYSTER LAMINATE THIS SIDE OPPOSITE SIDE LAMINATED PER SELECTION HOLES DO NOT GO THRU DIVIDER OYSTER BOTH SIDES HOLES GO THRU RIGHT END PANEL OYSTER LAMINATE THIS SIDE OPPOSITE SIDE LAMINATED PER SELECTION HOLES DO NOT GO THRU 34

35 DiviDer Panel identification (continued) PANELS FOR NOMINAL 40" DEEP BANKS EXCEPT 408 & 411 (37.12" X 83.5" TYPICAL) COLUMNS LEFT END PANEL OYSTER LAMINATE THIS SIDE OPPOSITE SIDE LAMINATED PER SELECTION HOLES DO NOT GO THRU DIVIDER OYSTER BOTH SIDES HOLES GO THRU SPECIAL PANELS FOR NOMINAL 40" DEEP BANKS (37.12" X 83.5" TYPICAL) COLUMNS 408 ONLY RIGHT END PANEL OYSTER LAMINATE THIS SIDE OPPOSITE SIDE LAMINATED PER SELECTION HOLES DO NOT GO THRU 2 SMALL HOLES IDENTIFY THESE PANELS AS SPECIAL 408 COLUMNS LEFT END PANEL OYSTER LAMINATE THIS SIDE OPPOSITE SIDE LAMINATED PER SELECTION HOLES DO NOT GO THRU DIVIDER OYSTER BOTH SIDES HOLES GO THRU RIGHT END PANEL OYSTER LAMINATE THIS SIDE OPPOSITE SIDE LAMINATED PER SELECTION HOLES DO NOT GO THRU 35

36 DiviDer Panel identification (continued) SPECIAL PANELS FOR NOMINAL 40" DEEP BANK (37.12" X 83.5" TYPICAL) COLUMNS 411 ONLY 1 SMALL HOLE IDENTIFIES THESE PANELS AS SPECIAL 411 COLUMNS 1 SMALL HOLE IDENTIFIES THESE PANELS AS SPECIAL 411 COLUMNS LEFT END PANEL OYSTER LAMINATE THIS SIDE OPPOSITE SIDE LAMINATED PER SELECTION HOLES DO NOT GO THRU DIVIDER OYSTER BOTH SIDES HOLES GO THRU RIGHT END PANEL OYSTER LAMINATE THIS SIDE OPPOSITE SIDE LAMINATED PER SELECTION HOLES DO NOT GO THRU TroubleshooTing If parts get mixed-up from the pallets: Look for part labels and put them back in order by bank, referencing the Specific Parts List. Consult the layout plan drawing for shelf placement based on the dimensions of a column. Consult the layout plan drawing for hole patterns for shelf placement on End Panels. Consult the layout plan drawing for any Special Panels needed and any special parts Once all parts are placed back in order by bank, begin the installation as instructed. If a Door Set needs to be removed: Top Panels must first be removed. Use a 2x4 and a Wonderbar to apply leverage to the bottom of the Extrusion to force it up and off of the pins. This requires two people. If an Extrusion or Door Set will not engage all three screws or is difficult to place: Slightly loosen the screws on the front edge of the panel. 36

Media Storage Systems Fixed Media Cabinets

Media Storage Systems Fixed Media Cabinets Owner s Manual Media Storage Systems Fixed Media Cabinets Contents 1-Column Fixed Media Storage Cabinet Important User Information...........................2 Safety Precautions.................................3

More information

Cabinet Storage Products

Cabinet Storage Products Assembly Instructions Storage Products (UltraStor, Acoustis, Adjustable Shelf, Cover Panels, Closure Panels) Wood Compartment Doors Full Wood Door Compartment Grille Doors Full Grille Door No Doors Contents

More information

Assembly Instructions Music Library System

Assembly Instructions Music Library System Assembly Instructions Music Library System 7-Shelf Unit is shown. 6-Shelf Unit assembly is the same except where noted. Contents Important User Information...........................2 General...2 Manufacturer...2

More information

Assembly Instructions flipforms

Assembly Instructions flipforms Assembly Instructions flipforms Contents Important User Information...........................2 General...2 Manufacturer...2 Intended Use...2 Warranty...2 Before You Begin...................................3

More information

Wenger Corporation 2014 Printed in USA 08/14 Part #145V Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota

Wenger Corporation 2014 Printed in USA 08/14 Part #145V Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota Assembly Instructions Wardrobe Cabinet CONTENTS Important User Information...........................2 General......................................2 Manufacturer.................................2 Intended

More information

Assembly Instructions Signature Choral Riser 4-Step Model

Assembly Instructions Signature Choral Riser 4-Step Model Assembly Instructions Signature Choral Riser 4-Step Model Contents Important User Information...........................2 General...2 Manufacturer...2 Intended Use...2 Warranty...2 Safety Precautions.................................3

More information

Select Lab Adjustable Height Workstation

Select Lab Adjustable Height Workstation Assembly Instructions Select Lab Adjustable Height Workstation Mobile version is shown. Also available without casters. Contents Important User Information.............................. 2 Safety Precautions....................................

More information

Select Lab Fixed Height Workstation

Select Lab Fixed Height Workstation Assembly Instructions Select Lab Fixed Height Workstation Contents Important User Information.............................. 2 Safety Precautions.................................... 3 Required Tools........................................

More information

Signature Choral Riser Side Rail

Signature Choral Riser Side Rail Assembly/Owner s Manual Signature Choral Riser Side Rail Signature Choral 3-Step Riser with Optional Side Rail Signature Choral 4-Step Riser with Optional Side Rail CONTENTS Visit the Signature Choral

More information

Essential Lab Workstation

Essential Lab Workstation Assembly Instructions Essential Lab Workstation Contents Important User Information...........................2 Required Tools.....................................3 Hardware Parts List.................................3

More information

GearBoss AirPro Locker

GearBoss AirPro Locker Installation and Owner s Instructions GearBoss AirPro Locker Wall Installation Island Installation Contents Important User Information...........................2 General...2 Manufacturer...2 Intended

More information

Elementary Storage Cabinets

Elementary Storage Cabinets Assembly Instructions Elementary Storage Cabinets ORFF Garage Small Instrument Cabinet (Cabinets Shown Fully Assembled) Poster Storage Cabinet CONTENTS Important User Information............................2

More information

Attic Accessory for 48 X-Cart

Attic Accessory for 48 X-Cart Assembly Instructions Attic Accessory for 48 X-Cart Short Attic Tall Attic 48 X-Cart with Short Attic Accessory CONTENTS Important User Information...2 General...2 Manufacturer...2 Installation...2 Intended

More information

Assembly Instructions and Owner s Manual Flex TechBridge

Assembly Instructions and Owner s Manual Flex TechBridge Assembly Instructions and Owner s Manual Flex TechBridge Contents Important User Information...........................2 Safety Precautions.................................2 Required Tools.....................................3

More information

Wenger Corporation 2010 Printed in China 02/10 Part #148H Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota

Wenger Corporation 2010 Printed in China 02/10 Part #148H Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota Assembly Instructions Violin/Viola Storage Rack CONTENTS Safety Precautions.................................. Warranty.......................................... Important User Information............................

More information

Wenger Corporation 2013 Printed in USA 08/13 Part #240B Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota

Wenger Corporation 2013 Printed in USA 08/13 Part #240B Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota Assembly Instructions SportCart CONTENTS Important User Information...2 General...2 Manufacturer...2 Installation...2 Intended Use...2 Warranty...2 Safety............................................3 General...3

More information

Drawer Unit Assembly. Wenger Corporation 2006 Printed in USA 12/06 Part #121B115-01

Drawer Unit Assembly. Wenger Corporation 2006 Printed in USA 12/06 Part #121B115-01 Assembly Instructions Rehearsal Resource Center Folio Box Option Model 121 Drawer Unit Assembly CONTENTS Warranty.......................................... 3 Important User Information............................

More information

Installation and Owner s Instructions Customizable Wood Lockers

Installation and Owner s Instructions Customizable Wood Lockers Installation and Owner s Instructions Customizable Wood Lockers Contents Important User Information...........................2 General...2 Manufacturer...2 Intended Use...2 Warranty...2 Safety Precautions.................................3

More information

GearBoss Shelving System

GearBoss Shelving System Assembly/Owner s Manual GearBoss Shelving System CONTENTS Safety...........................................2 General......................................2 Installation...................................2

More information

Peg Board Option for the GearBoss Shelving System

Peg Board Option for the GearBoss Shelving System Installation Instructions Peg Board Option for the GearBoss Shelving System Contents Important User Information...........................2 General...2 Manufacturer...2 Intended Use...2 Warranty...2 Safety

More information

OnBoard Bass Drum/Gong Cart

OnBoard Bass Drum/Gong Cart Assembly and Owner s Manual OnBoard Bass Drum/Gong Cart CONTENTS Important User Information...................................................................2 Safety...................................................................................3

More information

Please read and understand the OnBoard Timpani Cart Owner s Manual before using the Timpani Cart.

Please read and understand the OnBoard Timpani Cart Owner s Manual before using the Timpani Cart. Assembly and Owner s Manual OnBoard Timpani Cart Performance Position Towing Position CONTENTS Important User Information...........................2 General......................................2 Manufacturer.................................2

More information

GearBoss II High Density storage

GearBoss II High Density storage Assembly/Owner s Manual GearBoss II High Density storage contents Safety...........................................2 General......................................2 Installation...................................2

More information

Your Performance Partner

Your Performance Partner Assembly Instructions Attic Storage System Your Performance Partner CONTENTS Safety Precautions.................................. 2 Warranty.......................................... 2 Important User Information............................

More information

Guitar Mobile Storage Rack

Guitar Mobile Storage Rack Assembly Instructions Guitar Mobile Storage Rack CONTENTS Safety Precautions.................................. 2 Warranty.......................................... 2 Operation.........................................

More information

Guard Rail with In-Fill Panel

Guard Rail with In-Fill Panel Assembly Instructions Guard Rail for Wenger Versalite TM TM, Trouper, Stagehand, Portamaster, Showmaker Platform Systems Guard Rail with In-Fill Panel CONTENTS Important User Information...........................................................................

More information

Diva Acoustical Ceiling

Diva Acoustical Ceiling Installation Instructions Diva Acoustical Ceiling CONTENTS Important User Information...........................2 Safety Precautions.................................3 Required Tools....................................3

More information

Tablet Arm for Wenger Playright Chairs

Tablet Arm for Wenger Playright Chairs Assembly Instructions Tablet Arm for Wenger Playright Chairs CONTeNTs Before You Begin..........................................................2 Warranty.................................................................2

More information

a.k.a. casegoods instructions

a.k.a. casegoods instructions a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly

More information

High Density Sports Storage

High Density Sports Storage Owner s Manual High Density Sports Storage CONTENTS Safety...........................................2 General......................................2 Installation...................................2 Usage.......................................2

More information

Installation Instructions

Installation Instructions by Plato Woodwork Installation Instructions Plato Woodwork, Inc. 200 Third Street SW P.O. Box 98 Plato, MN 55370 www.platowoodwork.com 800.328.5924 SECTION GUIDE GETTING STARTED PAGE # Installation Methods...

More information

Video Wall Installation Instructions 2W X 3H, 3W X 3H

Video Wall Installation Instructions 2W X 3H, 3W X 3H Video Wall Installation Instructions 2W X 3H, 3W X 3H www.microndisplaysolutions.com Table of Contents Important Safety Instructions... 3 Configuration... 4 Package Contents, included and optional items...

More information

" BASE CABINET

 BASE CABINET INSTALLATION GUIDE INSTALLATION GUIDE Before You Begin Installing Your Kitchen Cabinets 1. Read through installation guide to understand all steps and gather tools needed. 2. Verify that all of the hardware,

More information

Assembly and Installation Guide

Assembly and Installation Guide The Easy Hang Closet Solution SM Install Your elfa In An Instant. Enjoy The Benefits For A Lifetime. Basic Tools For elfa Assembly and Installation Level Hand or Power Drill Drill Bits 1/8", 3/8", 5/16"

More information

Display Shelving Installation Instructions

Display Shelving Installation Instructions Display Shelving Installation Instructions Top Rail (R-T) Back (BE) (R-C) Splicer Rail (R-S) 78 H to 120 H only Uprite (U) Uprite End Trim (UET) Shelf Back (BE) Base End Trim (BET) (R-C) 96 H to 120 H

More information

Installation Manual. Solid Plastic Toilet Partitions. IN CANADA & AREAS OTHER THAN U.S.A.: IN THE U.S.A.:

Installation Manual. Solid Plastic Toilet Partitions.   IN CANADA & AREAS OTHER THAN U.S.A.: IN THE U.S.A.: Installation Manual Solid Plastic Toilet Partitions Toilet Partitions & Lockers IN THE U.S.A.: Hadrian Inc., 7420 Clover Avenue, Mentor, OH 44060 Telephone: 440-942-9118 Fax: 440-942-9618 U.S. toll free

More information

Top Closure Kit Accessory for Music Library System

Top Closure Kit Accessory for Music Library System Assembly Instructions Top Closure Kit Accessory for Music Library System Contents Required Tools.....................................2 Installation Requirements............................2 Fasteners -

More information

Oxford Stalls Installation Instructions

Oxford Stalls Installation Instructions Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or

More information

Laminate Cabinet Installation Instructions

Laminate Cabinet Installation Instructions Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper

More information

Installation Instructions

Installation Instructions Installation Instructions For Models: Model Number / Description File Name 1540 Classic Series P-Lam Toilet Partitions 1540.pdf 1 INSTALLATION INSTRUCTIONS LAMINATED PLASTIC TOILET PARTITIONS 1540 Classic

More information

Dura-Lock Roof System

Dura-Lock Roof System DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.

More information

INSTALL INSTRUCTIONS WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES NEWAGE STEEL WELDED CABINETRY

INSTALL INSTRUCTIONS WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES NEWAGE STEEL WELDED CABINETRY NEWAGE STEEL WELDED CABINETRY WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES ALL CABINETS MUST BE MOUNTED TO STUDS ON A SECURE WALL, AS PER THESE INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS LAMINATED P LASTIC TOILET PArTITIONS 1540 ClassicSeries with Options IMPORTANT: Storage and Handling Information on last page. For faster, easier installation, please review these

More information

Steel Solutions USA 602 E. Walnut Street Watseka, IL p: (888) f: (815)

Steel Solutions USA 602 E. Walnut Street Watseka, IL p: (888) f: (815) Steel Solutions USA 602 E. Walnut Street Watseka, IL 60970 p: (888) 875-5004 f: (815) 432-3364 sales@steelsolutionsusa.com Published February 2011 2011 Steel Solutions USA. All rights reserved. version

More information

Installation And Care Instructions. Vertical Honeycomb Shades

Installation And Care Instructions. Vertical Honeycomb Shades Installation And Care Instructions Vertical Honeycomb Shades Rev 5/2013 Table Of Contents Getting Started... 3 Parts Overview... 4 Materials Required... 5 Tools Required... 6 Outside Mount Installation...

More information

Install Guide. view our Install video guide online

Install Guide. view our Install video guide online view our Install video guide online CliqStudios.com LLC reserves the right to change, modify or discontinue policy, services and products at any time. All dimensions are nominal. Document only provided

More information

Closet System Installation Manual

Closet System Installation Manual Closet System Manual Thank you For choosing our Custom Closet Collection to fit all your needs Closets come fully assembled to make your project an enjoyable and satisfying experience. With quality Custom

More information

Extra Wide Heavy Duty Plastic Lockers Series Locker Installation Instructions

Extra Wide Heavy Duty Plastic Lockers Series Locker Installation Instructions Locker Installation Instructions Thank you for selecting Extra Wide Heavy Duty Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a good investment. These

More information

Performance 2.0 Series

Performance 2.0 Series Performance. Series Warning: Excessive weight hazard! Warning: Excessive weight hazard! Use two or more people to move, assemble, or install cabinets and locker to avoid back injury. Do not leave children

More information

Mighty Mo GX Series Cabinet Installation Guide. OR Rev /11

Mighty Mo GX Series Cabinet Installation Guide. OR Rev /11 Mighty Mo GX Series Cabinet Installation Guide OR-71601787 Safety and Warning ATTENTION The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating

More information

TIP FOR GETTING STARTED

TIP FOR GETTING STARTED Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these

More information

VYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4

VYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4 VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7

More information

EmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY

EmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B

More information

PRE-ENGINEERED HORSE STALL SYSTEMS SDFD SLIDING DOOR c/w FOLD-DOWN GRILL. & Assembly. Installation Instructions

PRE-ENGINEERED HORSE STALL SYSTEMS SDFD SLIDING DOOR c/w FOLD-DOWN GRILL. & Assembly. Installation Instructions PRE-ENGINEERED HORSE STALL SYSTEMS 4800 SDFD SLIDING DOOR c/w FOLD-DOWN GRILL & Assembly Installation Instructions 4800 SDFD Sliding Door c/w Fold-Down Grill Components - 1 3 /4" x 2" x 88" channels (2)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last

More information

NEXUS SERIES CABINETS

NEXUS SERIES CABINETS NEXUS SERIES CABINETS STANDARD BASE ASSEMBLY INSTRUCTIONS Also applies to: Galaxy Series, Nexus Series, Ridgeline Series, Statesman Series, and Waterford Series FOR YOUR INFORMATION: These assembly instructions

More information

6X3 Patio Garden Shed Assembly Manual

6X3 Patio Garden Shed Assembly Manual Thank you for purchasing a 6x3 Patio Garden Shed. Please take the time to identify all the parts prior to assembly. Revision #4 July 6th, 2016 6X3 Patio Garden Shed Assembly Manual Please use Safety Eyewear

More information

Worktop INDEX eight Capacity Unpacking

Worktop INDEX eight Capacity Unpacking Pro.0 Series Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of

More information

Installation Manual for Metal Toilet Partitions Standard Series

Installation Manual for Metal Toilet Partitions Standard Series For Video instructions http://www.hadrian-inc.com/tech-data/installation/toilet-partitions.aspx P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations

More information

R Form No MILLENNIUM GONDOLA / WALLCASE ASSEMBLY

R Form No MILLENNIUM GONDOLA / WALLCASE ASSEMBLY R06-19-06 - Form No.08335-0109 POST THIS WARNING PAGE IN A CONSPICUOUS PLACE, CLEARLY VISIBLE TO ALL STORE PERSONNEL READ BEFORE ASSEMBLING WARNING FOR YOUR SAFETY Install all shelving units according

More information

Before Assembling the Storage Wall

Before Assembling the Storage Wall Chapter 1 Assembling the Lista Storage Wall Lista provides two types of standard Storage Walls: B251 and B255. The design, construction, assembly, and quality are identical for both types, however, B251

More information

Chapter 18. Interior Doors

Chapter 18. Interior Doors Chapter 18. Interior Doors 18.1 SWINGING DOORS 18.2 SLIDING DOORS 18.3 BIFOLD DOORS Tools needed by volunteers: Hammer Nail apron Tape measure Square Pencil Tools and equipment needed: Extension cords

More information

Product must be installed as shown using the screws and brackets provided. Use of incorrect hardware could result in damage to the product.

Product must be installed as shown using the screws and brackets provided. Use of incorrect hardware could result in damage to the product. General Notes These installation instructions are intended to be comprehensive for a typical Keyeira/Presto configuration. Your configuration may differ. If you have questions contact Geiger Customer Service

More information

PART #MSP-DCCST Flat Panel Tilt Mount

PART #MSP-DCCST Flat Panel Tilt Mount INSTALLATION INSTRUCTIONS PART # Flat Panel Tilt Mount The Flat Panel Tilt Mount is a quick disconnect mounting solution for flat panel displays. The mount features adjustability between 0 and 15 degrees

More information

INSTALLATION AND CARE INSTRUCTIONS

INSTALLATION AND CARE INSTRUCTIONS INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades 52 C8-10-3401 Rev 2/14 CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5

More information

Important Loading Information. Tools Required. Meridian Lateral Files Instructions

Important Loading Information. Tools Required. Meridian Lateral Files Instructions Y Meridian Lateral Files Instructions! WARNING Failure to observe stated capacities below will result in unsafe usage conditions, causing possible product damage or personal injury. Important Loading Information

More information

CABINETRY Assembly Instructions

CABINETRY  Assembly Instructions www.hdicabinetry.com Assembly Instructions TABLE OF CONTENTS Category Page(s) Section 1: Framed Series Base Cabinet Instructions Wall Cabinet Instructions Easy Reach Cabinet Instructions 1.01-1.04 1.05-1.06

More information

ALUMA-VENT AWNING REGULAR END STYLE INSTALLATION INSTRUCTIONS

ALUMA-VENT AWNING REGULAR END STYLE INSTALLATION INSTRUCTIONS ALUMA-VENT AWNING REGULAR END STYLE INSTALLATION INSTRUCTIONS Contact us at: 1-888-442-2928 or www.americana.com Options in your kit: A. Splice Pg 16 B. Column Pg 17 C. C-Channel Brace Pg 19 D. Runner

More information

Menu Board Tilt or Fixed Mount Installation Instructions MDS1T-200, MDS1T-300, MDS1T-400 MDS2T-200, MDS2T-300, MDS2T-400 MDS3T-200, MDS3T-300, MDS3T-400 MDS4T-200, MDS4T-300, MDS4T-400 MDS5T-200, MDS5T-300,

More information

Franklin Mills Stackable Movable Lateral Instructions

Franklin Mills Stackable Movable Lateral Instructions Franklin Mills Stackable Movable Lateral Instructions Table of Contents: Table of contents...1 Tools Required...2 Stationary Shelving Assembly...3-7 Mobile Shelving Assembly...8-16 Rail Assembly...8-11

More information

Workbench Instructions for Assembly

Workbench Instructions for Assembly Workbench Instructions for Assembly Technical Electronic Workstations and Industrial Workbenches Includes: Cabinets Privacy Panels Stringers Bottom Shelves Table of Contents Tools Required for Assembly...

More information

TOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER.

TOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER. TOOLS REQUIRED FOR ASSEMBLY Rubber Mallet or Plastic Tip Hammer Top Cover Support PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER Back Stop Divider Closed 'L' Upright Slotted Reinforcement Support

More information

STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS

STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions

More information

INS A KSR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Verify Curb Installation Required Installation Tools...

INS A KSR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Verify Curb Installation Required Installation Tools... INS-88.300-0A KSR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE 1. Verify Curb Installation... 2 2. Required Installation Tools... 2 3. Unpacking the KSR... 3 4. Attach KSR Bottom Rail to Curb... 5 5. Attach

More information

StageTek Staging System

StageTek Staging System Owner s Manual StageTek Staging System CONTENTS Safety Precautions.................................2 Important User Information...........................2 Introduction.......................................3

More information

MobileTrak5 Installation Instructions

MobileTrak5 Installation Instructions MobileTrak5 Installation Instructions PLEASE OPEN ALL BOXES & CHECK TO MAKE SURE YOU HAVE ALL PIECES REQUIRED READ ALL INSTRUCTIONS BEFORE STARTING Tools Required for Assembly 7/16, 1/2 Wrench Phillips

More information

YUKON PATIO COVER INSTALLATION INSTRUCTIONS

YUKON PATIO COVER INSTALLATION INSTRUCTIONS YUKON PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin: Consult your local building department for any required permits You may be required to obtain a building permit for this structure. Contact

More information

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013 U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -

More information

Install Instructions. NewAge Steel Welded Tall Locker

Install Instructions. NewAge Steel Welded Tall Locker Kit Contains Full Width Adjustable Steel Shelves (4) Height-Adjustable Steel Leveling Legs (4) Aluminum Door Trim (2) 2.5 x ¼ Cabinet Mounting Lag Bolts (4) Large Zinc Plated Mounting Washers (4) 5/8 x

More information

Assembly Instructions

Assembly Instructions InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective

More information

Worktop. Weight Capacity. 100 lbs. 21 Corner Worktop. 48 Worktop. Fits over 2 Cabinets. 72 Worktop. Fits over 3 Cabinets. 200 lbs. 150 lbs.

Worktop. Weight Capacity. 100 lbs. 21 Corner Worktop. 48 Worktop. Fits over 2 Cabinets. 72 Worktop. Fits over 3 Cabinets. 200 lbs. 150 lbs. Bold.0 Warning: Excessive weight hazard! Use two or more people to move, assemble or install cabinets and locker to avoid back injury. Do not leave children unattended near cabinets. High risk of tipping

More information

BioPrism Solid Surface

BioPrism Solid Surface Please read all instructions before installing products. These instructions are intended for use with InPro s standard toilet partitions, which include 58 high doors and wall panels, when deviating from

More information

Installation Instructions for Bifold Doors (JII103)

Installation Instructions for Bifold Doors (JII103) Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for premium composite, hollow and solid core molded Bifold Doors. Bifolds are designed for fast

More information

GrowSpan Estate Pro I Greenhouse

GrowSpan Estate Pro I Greenhouse GrowSpan Estate Pro I Greenhouse Photo may show a different but similar model. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 104564 11'-8" W x

More information

Melamine Plastic Laminate. Toilet Partition Installation Manual

Melamine Plastic Laminate. Toilet Partition Installation Manual Melamine Plastic Laminate Toilet Partition Installation Manual PHONE: FAX: 1-866-317-2786 ATTENTION DO NOT MIX FASTENER PACKS EACH FASTENER PACK HAS THE NECESSARY BOLTS, BARRELS AND SCREWS TO INSTALL THE

More information

ClearSpan PolyMax Windbreak Wall

ClearSpan PolyMax Windbreak Wall ClearSpan PolyMax Windbreak Wall Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: February 2007ldg STK# DIMENSIONS

More information

Installation Manual for Metal Toilet Partitions Elite & Elite Plus Series

Installation Manual for Metal Toilet Partitions Elite & Elite Plus Series P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations 4 STEP 2: Fasten Floor Brackets 4 & 5 STEP 3: Erect Panels 6 STEP 4: Erect Wall Pilaster 7

More information

INS A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Unpacking the KSCR Splicing the KSCR (If Required)...

INS A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Unpacking the KSCR Splicing the KSCR (If Required)... INS-88.500-0A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE 1. Unpacking the KSCR... 2 2. Splicing the KSCR (If Required)... 4 3. Assemble Curb and Rail Corners... 5 4. Install Cross Bracing (If Required)...

More information

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY

Side Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT

More information

Mount to the Wall INSTALLATION MANUAL

Mount to the Wall INSTALLATION MANUAL Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced

More information

NX7 SERIES 5-1/2 HANDRAIL

NX7 SERIES 5-1/2 HANDRAIL STORAGE & HANDLING The handrails are shipped unassembled. Upon receipt, immediately check all material for any damage that may have occurred in transit and verify that all of the items and quantities are

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review

More information

** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at:

** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at: 3/01/2007 VISIT THE LITIME WEB SITE: WWW.LITIME.COM ** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at: 1 (800) 225-3865 Double Shed Doors for Back

More information

Installation Manual for Metal Emperor Lockers

Installation Manual for Metal Emperor Lockers P a g e 1 Table of Contents Page General Notes and Tools Required 2-3 Assemble Shelves with Coat Hooks/Coat Rods 4 Fastening Chart 5 Knock Down Locker Assembly (Banks of Three) 6-12 Appendix A: Dress End

More information

Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM

Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM Tilting & Swiveling Plasma/LCD Flat Panel Wall Mount Installation Guide Model: A380SM Easy installation Built-in level for easy positioning Corrective leveling adjustments after installation Forward /

More information

Chapter 22 - Cabinets & Vanities

Chapter 22 - Cabinets & Vanities Chapter 22 - Cabinets & Vanities Contents Chapter 22 - Cabinets & Vanities... 22-1 Timing & Prerequisites... 22-2 Cabinets... 22-3 Cabinet Layout... 22-3 Wall Cabinets... 22-4 Assemble the Wall Units...

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLine Series 1180 DuraLine Series Class-A Fire Rated IMPORTANT: Review these instructions thoroughly prior to installation. FLOOR ANCHORED

More information

Shop Style Miter Saw Stand Kit

Shop Style Miter Saw Stand Kit Quality Power Tool Accessories OWNER S MANUAL Assembled Unit Shown Without Shelves & Wings Assembled With Shelves & Wings Shop Style Miter Saw Stand Kit Model 2850 IMPORTANT Read and understand all safety

More information

Assembly and installation help

Assembly and installation help Assembly and installation help A supplement to the directions The Purpose of this tutorial is to expand (not replace) upon the directions that come with the system and to help provide shortcuts, the first

More information

Installation Operation Care

Installation Operation Care Installation Operation Care Palm Beach Polysatin Shutters CONTENTS Getting Started Installation Overview...1 Unpacking...1 Tools and Materials Needed...1 Fasteners...2 Frame Assembly Assemble the Frame

More information