FATIGUE BEHAVIOUR OF COMPOSITE JOINTS WITH HEXAGON BOLTS

Size: px
Start display at page:

Download "FATIGUE BEHAVIOUR OF COMPOSITE JOINTS WITH HEXAGON BOLTS"

Transcription

1 FATIGUE BEHAVIOUR OF COMPOSITE JOINTS WITH HEXAGON BOLTS Romn Strikov nd Jokim Schön Deprtment of Aeronutics, Royl Institute of Technology SE-1 44 Stockholm, Sweden Structures nd Mterils Deprtment, Aeronutics Division, FFA Swedish Defence Reserch Agency, SE Stockholm, Sweden SUMMARY: An experimentl ftigue progrm ws crried out on composite joints with titnium bolts. Single, double, nd triple-row double lp joints were tested in cyclic loding with the stress rtio, R = -1. In order to study the development of ftigue dmge in the joints bolt movement, reltive displcement between composite pltes, nd strin guge mesurements were used. Ftigue tests hve shown tht the ftigue resistnce of multirow joints is better thn tht of single-row joints. Direct mesurements of dmge development showed significnt influence of reduction in the pre-stress in the bolts nd ftigue degrdtion of the bolt holes on reltive displcement between composite pltes nd bolt movement. There ws significnt effect on the strin evolution from the bolts during ftigue loding. KEYWORDS: Bolted Joints, Ftigue, Bolt movement, Strin INTRODUCTION Advnced composite mterils re experiencing incresing use in the erospce industry becuse of their high strength-to-weight nd stiffness-to-weight rtios. In ircrft structures the lod between different prts is trnsferred by mechniclly fstened or bonded joints. In comprison with dhesive joining, mechnicl joints re used in cses when thick lmintes hve to be joined, when there is requirement for different prts of the sme structure to be disssembled for inspection, or repir purposes. However, bolt holes re stress concentrtion fctor in the composite joint pltes, which could significntly reduced the mechnicl performnce of joined structures. On the other hnd, ircrft structures experience vst spectrum of extreme service conditions tht include the presence of ftigue loding. The certifiction of ircrft requires tht ircrft components mnufctured from composite mterils be ble to withstnd the presence of ftigue loding in service [1 3]. Therefore, it would seem tht the ftigue behviour of composite joints plys n importnt role in the design nd performnce of ircrft composite structures. As previous investigtions hve shown, bolt movement is n importnt prt of the overll behviour of composite bolted joints. However, only few methods of boltmovement mesurement, such s the use of potentiometer trnsducer, low-kilovolt rdiogrphy, nd shdow moire techniques, hve been mentioned in the published literture [4 ]. Since most of them re quite complicted to mount nd use, new simple techniques re needed in order to observe processes ssocited with the bolt/composite

2 interfce. According to Ref. [7], the presence of fsteners hve n influence on the evolution of strin between them under loding. Therefore, it my be of interest to study this effect involving strin guge mesurements during ftigue tests. As it would seem, more experimentl dt nd some development in experimentl methods re required to understnd more deeply the ftigue behviour of composite bolted joints in order to improve the totl mechnicl performnce of composite structures contining bolted connections. The objective of this investigtion is to obtin experimentl results on the ftigue behviour of composite joints with different configurtion nd geometry. Strin guge mesurements re to be crried out between bolt rows during ftigue tests. Bolt-movement mesurements re to be done to nlyse the ftigue process in the bolt/composite interfce. Reltive displcement between the joint pltes is to be mesured using extensometers. EXPERIMENTAL PROCEDURE Specimen pltes were mnufctured from crbon fibre/epoxy mteril system (HTA7/37). A qusi-isotropic ly-up, (45//9) nd (45//9), ws used for outer nd middle pltes. The composite pltes were joined by two, four, nd six titnium Hexgon bolts s shown in Fig Η1 Η Η (c) Fig. 1: Specimens tested in ftigue. The nominl bolt dimeter ws mm. This gives the following geometric rtio of the lminte strip width, edge distnce nd thickness to the bolt dimeter: w/d = 4.5, e/d = 2.5, nd t/d = 1.4. The Hexgon bolts were tightened to torque of 9 Nm.

3 Strin guges were pplied on some of the double lp joints in order to mesure strin between different bolt rows. Figure 2 shows the loctions of the strin guges on the specimen surfce. The strin guges were glued on one of the outer pltes nd bolt row 1 st bolt row bolt No.3 bolt No.1 SG rd bolt row 2 nd bolt row 1 st bolt row bolt No.5 bolt No.3 bolt No.1 SG1 SG5 bolt No.4 SG4 SG3 bolt No.2 bolt No. SG9 SG8 SG4 SG3 bolt No.2 SG2 SG7 SG2 SG1 SG SG Fig. 2: Strin guge positions on the specimen surfce with four nd six bolts. In order to mesure reltive displcement between two composite pltes, extensometers were used s shown in Fig. 3. Extensometer holders for extensometer No ~2 res of ttchment for extensometer holder holders for extensometer No.2 Lod direction holders for extensometer Fig. 3: Appliction of extensometers: for reltive displcement mesurements between composite pltes; for bolt-movement mesurements. To mesure bolt movement, specil fixture ws built nd ttched together with n extensometer to the specimen s shown in Fig. 3. The specimens were ftigue tested t different lod levels with the stress rtio, R = /, equl to -1. An luminium lterl support ws used to prevent buckling of the joints s shown in Fig. 4.

4 lterl support specimen teflon films loding grip Fig. 4: The testing mchine grips with the specimen nd test fixture. The specimen pltes nd the lterl support were interleved with Teflon sheets to decrese the friction force between the composite pltes nd the fixture set-up. All ftigue tests were performed under the lod control mode of the testing mchine to ssure tht constnt mximum nd minimum lternting lod will be pplied to the specimen. The testing mchine ws set to stop cyclic loding when the grip-displcement limit ws reched nd ftigue filure ws thus ssumed to hve occurred. This limit ws determined by dding.8 mm to the totl deflection mgnitude of the specimen during ftigue loding. The deflection ws monitored using n IBM PC. The bolt temperture ws mesured to mke sure heting did not occur in specimen. The mximum temperture limit ws set to +33 C. If heting occurred the frequency of the test ws reduced. All experiments were performed t room temperture ( 22 C) nd mbient reltive humidity ( 5 ). EXPERIMENTAL RESULTS AND DISCUSSIONS Ftigue resistnce of the joints The ftigue test results re presented in Fig. 5 together with the ultimte tensile strength nd strin for ech joint configurtion tken from [7]. The lines in the plots re from lest squres fit to the logrithmic ftigue dt., (MP) σ two bolts four bolts six bolts Number of cycles

5 , (%) ε two bolts four bolts six bolts Number of cycles Fig. 5: Ftigue test results. As seen, the joints with six bolts performed the highest resistnce to ftigue, followed by the joints with four bolts. The lowest ftigue resistnce ws shown by the joint with two bolts. In most of the ftigue tests, filure of the specimens occurred becuse of ftigue filure of fsteners. The specimens with two bolts filed fter one bolt broke (see Fig. ); wheres the joints with four nd six bolts filed fter t lest two fsteners frctured (see Fig. nd (c)). (c) (d) Fig. : Ftigue tested joints. Specimens with six bolts, tested t = 275 MP nd higher lod levels, filed either due to net-section filure occurred or due to ftigue filure of bolts followed by netsection filure (see Fig. (d)). It is believed tht fter the frcture of bolts the net-section trnsferred more lod. This eventully resulted in net-section secondry filure mode.

6 δ σ σ σ σ Reltive displcement between pltes Reltive displcement between two composite pltes ws mesured fter different number of cycles. The mesured results re presented s extensometer-displcement rnge,, which is the pek to pek reltive displcement between the pltes during the compression nd tension prts of lod cycle s shown in Fig. 7. The obtined results for two specimens with six bolts, tested t = 27 MP nd 35 MP, re shown in Fig. 7. Extensometer displcement, (mm) EXT Time, (s) EXT, (mm) δ 1.9 EXT1 EXT1 = 27 MP = 35 MP EXT2 EXT2 = 27 MP = 35 MP b Number of cycles Fig. 7: Extensometer displcement: nomenclture; the mesured results. The extensometer curves show tht chnges in reltive displcement between the pltes occur quite erly. At the beginning of ftigue loding the extensometers mesured decrese in the reltive displcement between the composite pltes which might be due to n increse in the coefficient of friction between the composite pltes [8]. This induced n increse in the friction force between the pltes, thereby cusing less displcement between the pltes. In ddition, ftigue debris ccumulted in the bolt holes could fill the clernce between the fsteners nd the hole surfce. This would reduce the spce for the bolt to move, nd s result, the reltive displcement between the pltes would decrese s well. As the number of cycles increses, the curves show slow increse in the reltive displcement between the composite pltes. This is cused by the growth of ftigue dmge in the bolt holes resulting in their elongtion. Removl of ftigue debris from the bolt holes would crete more vilble spce for the bolts to move, thus prtilly resulting in the slow increse in the reltive displcement between the composite pltes. At the sme time, the coefficient of friction could decrese due to wer of the pltes [8] nd the friction force decreses due to the reduction in the clmping force in the bolts. This would increse the reltive displcement between the composite pltes s well. The joints bolted by six fsteners filed fter t lest two bolts broke. In Fig. 7 point (1) nd (b1) reflect the first filure of bolts. As seen, this resulted in n incresed reltive displcement mesured by tht extensometer, which ws ttched on the sme hlf of the specimens were the bolt filure occurred. However, in one cse the second extensometer mesured drop in the reltive displcement between the pltes, wheres for nother joint the EXT2 curve does not show ny effect from the bolt filure on the extensometer mesurements. Point (2) corresponds to the second filure of bolt, which chnged the following extensometer mesurements. After this, the reltive displcement for the first

7 extensometer incresed, wheres the second extensometer mesured smll decrese in the reltive displcement. As cn be seen, even fter the second bolt frctured the specimen ws still ble to support ftigue loding until ftigue filure of bolt No. 5. Bolt-movement mesurements Since the joints mostly suffered from ftigue filure of bolts, it ws of interest to nlyse the ftigue behviour of the fsteners under cyclic loding. Bolt-movement mesurements were done on bolt No. 1 nd No. 3 from specimens with four bolts (see Fig. 2). One specimen with two bolts ws ftigue tested with bolt-movement mesurement on bolt No. 1. The obtined mesurement results re presented together with the gripdisplcement curves in Fig. 8 for specimens with two nd four bolts, which were tested t = 155 MP nd 127 MP, respectively. Rnge of grip displcement grip displcement bolt No Number of cycles Rnge of bolt movement, (mm) Rnge of grip displcement grip displcement bolt No.1 bolt No Number of cycles Rnge of bolt movement, (mm) Fig. 8: The mesured results of bolt movement: specimen with two bolts; specimen with four bolts. The grip displcement nd bolt movement re chrcterized by three different stges of evolution. At the beginning of the ftigue tests, ll curves show decrese in the

8 grip displcement nd bolt movement. The initil decrese hs the sme cuse s in the extensometer curves bove. The further evolution of the grip displcement nd the bolt movement is believed to be ffected by reduction in pre-stress in the bolts nd ftigue degrdtion of the bolt holes nd the composite round them. The reduction in the pre-stress in the bolts results in lower friction force between the composite pltes thn it ws t the beginning of cyclic loding. Therefore, less lod is trnsferred between the pltes by the friction force, which increses the displcement between the pltes nd more lod being trnsferred by the bolts. In ddition, t this stge of the ftigue tests very often ccumulted ftigue debris were observed trnsporting out of the bolt holes by visul inspection of the specimens. Ftigue prticles re cused by wer nd re-deposition of composite mteril round the bolt holes (see Fig. 9) nd bolt movement under loding []. Fig. 9: The middle plte of specimen with four bolts tested t = 1 MP. Becuse of the removl of ftigue debris, the clernce between the fsteners nd the bolt holes incresed, thus inducing more movement of the bolts during ftigue loding of the specimens. Filure of the joints with two bolts occurred fter ftigue filure of one bolt; wheres the joints with four bolts filed fter filure of two bolts. In Fig. 8 point (1) is mrked. The point corresponds to ftigue filure of bolt No. 2 (see Fig. 2) fter cycles. This induced more movement on bolt No. 1, but the bolt No. 3 curve shows drop in the bolt movement fter this number of cycles. Further evolution of the grip displcement nd the bolt movement show more grdul growth in the curves rising from dditionl dmge development in the specimen, except for bolt No. 3. Strin guge loops It ws found tht the influence of the bolt presence on the strin guges is more pronounced for those strin guges, which were locted between two bolts (see Fig. 2). Therefore, it my be interesting to nlyse the ftigue behviour of these strin guges s function of number of cycles. Figure 1 shows strin guge loops for specimens with four nd six bolts. The different loops hve been shifted 2 strin to fcilitte observtion. The loop rrows in the plots indicte their direction.

9 1 15 Lod, (kn) c t Strin*1, (ustr) c t c t 1st cycle 1 cycles 25 cycles 34 cycles 42 cyces Lod, kn t t t t c c c c Strin*1, (ustr) 2nd cycle 1 cycles 51 cycles 75 cycles 1 cycles 15 1 Lod, kn nd cycle 1 cycles 3125 cycles 475 cycles Strin*1, (ustr) (c) Fig. 1: Strin guge loops fter different number of cycles As the plots in Fig. 1 nd show, ll strin guge loops contin some points of inflection, which re mrked s ( ) nd ( ) for the tensile nd compression prts of the lod cycle, respectively. These points could be result of bolt-movement influence during cyclic loding. Due to lod trnsfer nd bolt bending, the bolts crete contct forces in the re between them, i.e., the re where strin guge No. 3 ws locted. The contct forces cused compressive deformtion in the region between the bolts. Therefore, the strin guge loops show n insignificnt increse in strin with further loding. Moreover, the lod level t which these points pper, decrese with incresing number of cycles. For exmple in Fig. 1, point ( ) in the first loop ppers t 4 kn, wheres fter 42 cycles the sme point cn be defined t 2 kn. It cn be expected tht t the beginning of the ftigue test some lod is trnsferred by the friction force between the specimen pltes. This will soften the inflection points. As ftigue loding proceeded, relxtion in the fsteners occurred, decresing the friction force nd thus inducing more lod being trnsferred by the bolts. As result, the bolt influence on the strin loop would occur t lower lod level within one lod cycle thn it ws t the beginning of the ftigue test. At this stge of the ftigue test the inflection points become shrper thn t its beginning. Figure 1(c) shows strin guge No. 8 loops for the specimen with six bolts. Anlysis of the mesurements found tht strin guge No. 8 behved similr to strin guge No. 3, especilly fter lrge number of cycles. Despite tht the hysteresis is not s pronounced s for strin guge No. 3, its shpe looks similr. However, it should be noted tht the mesurement on strin guge No. 8 were done only until 475 cycles,

10 when during visul inspection of the specimen two crcks in the surfce ply of the composite plte were found propgting under the strin guge, thereby cusing erroneous redings. CONCLUSIONS Specimens with two, four, nd six titnium bolts were tested in ftigue. The dominnt filure mode ws ftigue filure of bolts. Since for the joints with more thn two bolts filure occurred fter t lest two bolts broke, this would not be considered indictive of ctstrophic filure. Reltive displcement between composite pltes nd bolt movement under cyclic loding re gretly ffected by reduction in the pre-stress in the bolts, ftigue degrdtion of the composite mteril round the bolt holes, nd ftigue elongtion of the bolt holes. Strin guge mesurements between bolts showed tht the bolt presence hs significnt effect on the strin evolution during ftigue tests. References [1] Rpoff AJ, Dill HD. Certifiction of dmge tolernt composite structures. In: Proceedings of the Eighth DOD/NASA/FAA Conference on Fibrous Composites in Structurl Design (Prt 2), Lngley Reserch Center, NASA, September 199. p [2] Rubin AM. Common filure modes for composite ircrft structures due to secondry lods. Composites Engineering 1992;2(5-7): [3] Ashton HR. Dmge tolernce nd durbility testing for F/A-18 E/F composite mterils structures. In: Proceedings of the 37th AIAA/ASME/ASCE/AHS/ASC Structures, Structurl Dynmics, nd Mterils Conference, Slt Lke City, UT, April p [4] Cooper C, Turvey GJ. Effects of joint geometry nd bolt torque on the structurl performnce of single bolt tension joints in pultruded GRP sheet mterils. Composite Structures 1995;32: [5] Rmkumr RL, Tossvinen EW. Strength nd lifetime of bolted lmintes. Ftigue in Mechniclly Fstened Composite nd Metllic Joints, ASTM STP 927, Americn Society for Testing nd Mterils, Phildelphi 198. p [] Sunders DS, Gle S, Deirmendsin G. The development of ftigue dmge round fstener holes in thick grphite/epoxy composite lmintes. Composites 1993;24(4): [7] Strikov R, Schön J. Qusi-sttic behviour of composite joints with protrudinghed bolts. Composite Structures 21;51(4): [8] Schön J. Coefficient of friction of composite delmintion surfces. Wer 2;237: [9] Sunders DS, Gle SC, Deirmendjin GK. The development of ftigue dmge round fstener holes in thick grphite/epoxy composite lmintes. Composites 1993;24(4):

EXPERIMENTAL INVESTIGATION OF FATIGUE BEHAVIOUR IN COMPOSITE BOLTED JOINTS

EXPERIMENTAL INVESTIGATION OF FATIGUE BEHAVIOUR IN COMPOSITE BOLTED JOINTS EXPERIMENTAL INVESTIGATION OF FATIGUE BEHAVIOUR IN COMPOSITE BOLTED JOINTS Roman Starikov 1 and Joakim Schön 2 1 Department of Aeronautics, Royal Institute of Technology SE-1 44 Stockholm, Sweden 2 Structures

More information

MODELING THE INFLUENCE OF STITCHING ON DELAMINATION GROWTH IN STITCHED WARP-KNIT COMPOSITE LAP JOINTS

MODELING THE INFLUENCE OF STITCHING ON DELAMINATION GROWTH IN STITCHED WARP-KNIT COMPOSITE LAP JOINTS MODELING THE INFLUENCE OF STITCHING ON DELAMINATION GROWTH IN STITCHED WARP-KNIT COMPOSITE LAP JOINTS E.H. Glessgen, I.S. Rju 2 nd C.C. Poe, Jr. 2 Ntionl Reserch Council 2 Mechnics of Mterils Brnch NASA

More information

Experiment 3: Non-Ideal Operational Amplifiers

Experiment 3: Non-Ideal Operational Amplifiers Experiment 3: Non-Idel Opertionl Amplifiers Fll 2009 Equivlent Circuits The bsic ssumptions for n idel opertionl mplifier re n infinite differentil gin ( d ), n infinite input resistnce (R i ), zero output

More information

Experiment 3: Non-Ideal Operational Amplifiers

Experiment 3: Non-Ideal Operational Amplifiers Experiment 3: Non-Idel Opertionl Amplifiers 9/11/06 Equivlent Circuits The bsic ssumptions for n idel opertionl mplifier re n infinite differentil gin ( d ), n infinite input resistnce (R i ), zero output

More information

Synchronous Machine Parameter Measurement

Synchronous Machine Parameter Measurement Synchronous Mchine Prmeter Mesurement 1 Synchronous Mchine Prmeter Mesurement Introduction Wound field synchronous mchines re mostly used for power genertion but lso re well suited for motor pplictions

More information

ABB STOTZ-KONTAKT. ABB i-bus EIB Current Module SM/S Intelligent Installation Systems. User Manual SM/S In = 16 A AC Un = 230 V AC

ABB STOTZ-KONTAKT. ABB i-bus EIB Current Module SM/S Intelligent Installation Systems. User Manual SM/S In = 16 A AC Un = 230 V AC User Mnul ntelligent nstlltion Systems A B 1 2 3 4 5 6 7 8 30 ma 30 ma n = AC Un = 230 V AC 30 ma 9 10 11 12 C ABB STOTZ-KONTAKT Appliction Softwre Current Vlue Threshold/1 Contents Pge 1 Device Chrcteristics...

More information

Module 9. DC Machines. Version 2 EE IIT, Kharagpur

Module 9. DC Machines. Version 2 EE IIT, Kharagpur Module 9 DC Mchines Version EE IIT, Khrgpur esson 40 osses, Efficiency nd Testing of D.C. Mchines Version EE IIT, Khrgpur Contents 40 osses, efficiency nd testing of D.C. mchines (esson-40) 4 40.1 Gols

More information

Localization of Latent Image in Heterophase AgBr(I) Tabular Microcrystals

Localization of Latent Image in Heterophase AgBr(I) Tabular Microcrystals Interntionl ymposium on ilver Hlide Technology Locliztion of Ltent Imge in Heterophse AgBr(I) Tulr Microcrystls Elen V. Prosvirkin, Aigul B. Aishev, Timothy A. Lrichev, Boris A. echkrev Kemerovo tte University,

More information

Experiment 8 Series DC Motor (II)

Experiment 8 Series DC Motor (II) Ojectives To control the speed of loded series dc motor y chnging rmture voltge. To control the speed of loded series dc motor y dding resistnce in prllel with the rmture circuit. To control the speed

More information

Synchronous Machine Parameter Measurement

Synchronous Machine Parameter Measurement Synchronous Mchine Prmeter Mesurement 1 Synchronous Mchine Prmeter Mesurement Introduction Wound field synchronous mchines re mostly used for power genertion but lso re well suited for motor pplictions

More information

The Discussion of this exercise covers the following points:

The Discussion of this exercise covers the following points: Exercise 4 Bttery Chrging Methods EXERCISE OBJECTIVE When you hve completed this exercise, you will be fmilir with the different chrging methods nd chrge-control techniques commonly used when chrging Ni-MI

More information

Roller chains. Roller chains

Roller chains. Roller chains re chrcterised by n bove-verge service life due to excellent wer resistnce, high consistency, mtchless precision nd considerbly higher breking strength nd ftigue strength thn required by DIN/ ISO stndrd.

More information

DYE SOLUBILITY IN SUPERCRITICAL CARBON DIOXIDE FLUID

DYE SOLUBILITY IN SUPERCRITICAL CARBON DIOXIDE FLUID THERMAL SCIENCE, Yer 2015, Vol. 19, No. 4, pp. 1311-1315 1311 DYE SOLUBILITY IN SUPERCRITICAL CARBON DIOXIDE FLUID by Jun YAN, Li-Jiu ZHENG *, Bing DU, Yong-Fng QIAN, nd Fng YE Lioning Provincil Key Lbortory

More information

Three-Phase Synchronous Machines The synchronous machine can be used to operate as: 1. Synchronous motors 2. Synchronous generators (Alternator)

Three-Phase Synchronous Machines The synchronous machine can be used to operate as: 1. Synchronous motors 2. Synchronous generators (Alternator) Three-Phse Synchronous Mchines The synchronous mchine cn be used to operte s: 1. Synchronous motors 2. Synchronous genertors (Alterntor) Synchronous genertor is lso referred to s lterntor since it genertes

More information

Experimental evaluation of polycrystalline diamond tool geometries while drilling carbon fiber-reinforced plastics

Experimental evaluation of polycrystalline diamond tool geometries while drilling carbon fiber-reinforced plastics Int J Adv Mnuf Technol (14) 71:195 137 DOI 1.17/s17-13-559-7 ORIGINAL ARTICLE Experimentl evlution of polycrystlline dimond tool geometries while drilling cron fier-reinforced plstics Y. Krpt & B. Değer

More information

Available online at ScienceDirect. 6th CIRP International Conference on High Performance Cutting, HPC2014

Available online at   ScienceDirect. 6th CIRP International Conference on High Performance Cutting, HPC2014 Aville online t www.sciencedirect.com ScienceDirect Procedi CIRP 4 ( 4 ) 76 8 6th CIRP Conference on High Performnce Cutting, HPC4 Investigting Eccentricity Effects in Turn-Milling Opertions Emre Uysl,Umut

More information

Exercise 1-1. The Sine Wave EXERCISE OBJECTIVE DISCUSSION OUTLINE. Relationship between a rotating phasor and a sine wave DISCUSSION

Exercise 1-1. The Sine Wave EXERCISE OBJECTIVE DISCUSSION OUTLINE. Relationship between a rotating phasor and a sine wave DISCUSSION Exercise 1-1 The Sine Wve EXERCISE OBJECTIVE When you hve completed this exercise, you will be fmilir with the notion of sine wve nd how it cn be expressed s phsor rotting round the center of circle. You

More information

Update B158J New Chip Breaker Inserts for Turning Expanded Inserts

Update B158J New Chip Breaker Inserts for Turning Expanded Inserts 2009.4 Updte B158J Expnded s New Chip Breker s for Turning Breker Offers the best performnce for utomotive prts pplictions! ysmooth chip control even t vried depths of cut, feeds nd cutting speeds! New

More information

MSC Studentenwettbewerb. Wintersemester 2012/13. Marc/Mentat 2012

MSC Studentenwettbewerb. Wintersemester 2012/13. Marc/Mentat 2012 MSC Studentenwettewer Wintersemester 2012/13 Mrc/Mentt 2012 Aufge Wie groß ist die mximle Verschieung in Y Richtung im nichtlineren Fll? Required File: tip_lod.mud. 2 TUTORIAL Prolem Description In this

More information

EET 438a Automatic Control Systems Technology Laboratory 5 Control of a Separately Excited DC Machine

EET 438a Automatic Control Systems Technology Laboratory 5 Control of a Separately Excited DC Machine EE 438 Automtic Control Systems echnology bortory 5 Control of Seprtely Excited DC Mchine Objective: Apply proportionl controller to n electromechnicl system nd observe the effects tht feedbck control

More information

How to remove BRNS/BRFS series from a PWB

How to remove BRNS/BRFS series from a PWB Applictions mnul for BRNS/BRFS series How to remove BRNS/BRFS series from PWB VER1.0 Applictions Mnul BRNS/BRFS series Pge 1. Overview 1-1 1.1 Overview 1-1 2. Preprtion 2-1 2.1 2.2 2.3 Removl tool Adhesive

More information

THE EFFECT OF DOWEL SPACING ON THE STRESS AND STRAIN OF CASE-TYPE FURNITURE CORNER JOINT

THE EFFECT OF DOWEL SPACING ON THE STRESS AND STRAIN OF CASE-TYPE FURNITURE CORNER JOINT THE EFFECT OF DOWEL SPACING ON THE STRESS AND STRAIN OF CASE-TYPE FURNITURE CORNER JOINT Seid Hjdrević, Sndr Mrtinović Astrct University of Srjevo, Mechnicl Engineering Fculty, Vilsonovo setliste 9, Srjevo

More information

A Development of Earthing-Resistance-Estimation Instrument

A Development of Earthing-Resistance-Estimation Instrument A Development of Erthing-Resistnce-Estimtion Instrument HITOSHI KIJIMA Abstrct: - Whenever erth construction work is done, the implnted number nd depth of electrodes hve to be estimted in order to obtin

More information

University of North Carolina-Charlotte Department of Electrical and Computer Engineering ECGR 4143/5195 Electrical Machinery Fall 2009

University of North Carolina-Charlotte Department of Electrical and Computer Engineering ECGR 4143/5195 Electrical Machinery Fall 2009 Problem 1: Using DC Mchine University o North Crolin-Chrlotte Deprtment o Electricl nd Computer Engineering ECGR 4143/5195 Electricl Mchinery Fll 2009 Problem Set 4 Due: Thursdy October 8 Suggested Reding:

More information

Engineer-to-Engineer Note

Engineer-to-Engineer Note Engineer-to-Engineer Note EE-297 Technicl notes on using Anlog Devices DSPs, processors nd development tools Visit our Web resources http://www.nlog.com/ee-notes nd http://www.nlog.com/processors or e-mil

More information

CHAPTER 2 LITERATURE STUDY

CHAPTER 2 LITERATURE STUDY CHAPTER LITERATURE STUDY. Introduction Multipliction involves two bsic opertions: the genertion of the prtil products nd their ccumultion. Therefore, there re two possible wys to speed up the multipliction:

More information

MAXIMUM FLOWS IN FUZZY NETWORKS WITH FUNNEL-SHAPED NODES

MAXIMUM FLOWS IN FUZZY NETWORKS WITH FUNNEL-SHAPED NODES MAXIMUM FLOWS IN FUZZY NETWORKS WITH FUNNEL-SHAPED NODES Romn V. Tyshchuk Informtion Systems Deprtment, AMI corportion, Donetsk, Ukrine E-mil: rt_science@hotmil.com 1 INTRODUCTION During the considertion

More information

Array chip resistors size ARC241/ARC242 ARV241/ARV242

Array chip resistors size ARC241/ARC242 ARV241/ARV242 Arry chip resistors FEATURES 4 0603 sized resistors in one 1206-sized pckge Reduced reel exchnge time Low ssembly costs Reduced PCB re Reduced size of finl equipment Higher component nd equipment relibility.

More information

MSRS90. Hi efficiency Notched and No-hand insert for MSRS90

MSRS90. Hi efficiency Notched and No-hand insert for MSRS90 MGCO MR90 Multiple Cutter i efficiency Notched nd Nohnd insert for MR90 1Notched insert reduces cutting force reduction t the first pss tle mchining without chtter 2mooth chip evcution Prevents frcture

More information

ARC DISCHARGE AND EROSION BEHAVIOR OF SILVER ELECTRIC CONTACTS BETWEEN STATIC GAP

ARC DISCHARGE AND EROSION BEHAVIOR OF SILVER ELECTRIC CONTACTS BETWEEN STATIC GAP ARC DISCHARGE AND EROSION BEHAVIOR OF SILVER ELECTRIC CONTACTS BETWEEN STATIC GAP Chung, H-H. 1 Lee, R-T. 2. Chiou, Y-C. 2 1 Deprtment of Automtion Engineering Ko-Yun Institute of Technology 2 Deprtment

More information

PRO LIGNO Vol. 11 N pp

PRO LIGNO Vol. 11 N pp THE INFLUENCE OF THE TOOL POINT ANGLE AND FEED RATE ON THE DELAMINATION AT DRILLING OF PRE-LAMINATED PARTICLEBOARD Mihi ISPAS Prof.dr.eng. Trnsilvni University of Brsov Fculty of Wood Engineering Address:

More information

University of Dayton Research Institute Dayton, Ohio, Materials Laboratory Wright Patterson AFB, Ohio,

University of Dayton Research Institute Dayton, Ohio, Materials Laboratory Wright Patterson AFB, Ohio, LEAKY PLATE WAVE INSPECTION OF BIAXIAL COMPOSITES Richrd W. Mrtin University of Dyton Reserch Institute Dyton, Ohio, 45469-0001 Dle E. Chimenti Mterils Lortory Wright Ptterson AFB, Ohio, 45433-6533 INTRODUCTION

More information

Pulse and frequency responses of broadband low frequency ultrasonic transducers

Pulse and frequency responses of broadband low frequency ultrasonic transducers Pulse nd frequency responses of rodnd low frequency ultrsonic trnsducers A. Vldišusks, L. Mžeik, R. Šliteris, R. Rišutis, A. Jnkusks Ultrsound Institute, Kuns University of Technology, Studentu 5, LT1368

More information

Electronic Circuits I - Tutorial 03 Diode Applications I

Electronic Circuits I - Tutorial 03 Diode Applications I Electronic Circuits I - Tutoril 03 Diode Applictions I -1 / 9 - T & F # Question 1 A diode cn conduct current in two directions with equl ese. F 2 When reverse-bised, diode idelly ppers s short. F 3 A

More information

Synchronous Generator Line Synchronization

Synchronous Generator Line Synchronization Synchronous Genertor Line Synchroniztion 1 Synchronous Genertor Line Synchroniztion Introduction One issue in power genertion is synchronous genertor strting. Typiclly, synchronous genertor is connected

More information

This is a repository copy of Effect of power state on absorption cross section of personal computer components.

This is a repository copy of Effect of power state on absorption cross section of personal computer components. This is repository copy of Effect of power stte on bsorption cross section of personl computer components. White Rose Reserch Online URL for this pper: http://eprints.whiterose.c.uk/10547/ Version: Accepted

More information

MSRS90. Notched Inserts Reduce Cutting Forces When Entering the Workpiece Stable Machining without Chattering

MSRS90. Notched Inserts Reduce Cutting Forces When Entering the Workpiece Stable Machining without Chattering 90 Notched Inserts Reduce Cutting Forces When ntering the Workpiece tle Mchining without Chttering mooth Chip vcution Prevents Frcturing Cused y Biting Chips MGACOAT NANO For xtended Tool Life igh Mchining

More information

THE STUDY OF INFLUENCE CORE MATERIALS ON TECHNOLOGICAL PROPERTIES OF UNIVERSAL BENTONITE MOULDING MATERIALS. Matej BEZNÁK, Vladimír HANZEN, Ján VRABEC

THE STUDY OF INFLUENCE CORE MATERIALS ON TECHNOLOGICAL PROPERTIES OF UNIVERSAL BENTONITE MOULDING MATERIALS. Matej BEZNÁK, Vladimír HANZEN, Ján VRABEC THE STUDY OF INFLUENCE CORE MATERIALS ON TECHNOLOGICAL PROPERTIES OF UNIVERSAL BENTONITE MOULDING MATERIALS Mtej BEZNÁK, Vldimír HANZEN, Ján VRABEC Authors: Mtej Beznák, Assoc. Prof. PhD., Vldimír Hnzen,

More information

First Round Solutions Grades 4, 5, and 6

First Round Solutions Grades 4, 5, and 6 First Round Solutions Grdes 4, 5, nd 1) There re four bsic rectngles not mde up of smller ones There re three more rectngles mde up of two smller ones ech, two rectngles mde up of three smller ones ech,

More information

Investigation of Ground Frequency Characteristics

Investigation of Ground Frequency Characteristics Journl of Electromgnetic Anlysis nd Applictions, 03, 5, 3-37 http://dx.doi.org/0.436/jem.03.58050 Published Online August 03 (http://www.scirp.org/journl/jem) Mohmed Nyel Electricl Engineering Deprtment,

More information

Design And Implementation Of Luo Converter For Electric Vehicle Applications

Design And Implementation Of Luo Converter For Electric Vehicle Applications Design And Implementtion Of Luo Converter For Electric Vehicle Applictions A.Mnikndn #1, N.Vdivel #2 ME (Power Electronics nd Drives) Deprtment of Electricl nd Electronics Engineering Sri Shkthi Institute

More information

Simulation of Transformer Based Z-Source Inverter to Obtain High Voltage Boost Ability

Simulation of Transformer Based Z-Source Inverter to Obtain High Voltage Boost Ability Interntionl Journl of cience, Engineering nd Technology Reserch (IJETR), olume 4, Issue 1, October 15 imultion of Trnsformer Bsed Z-ource Inverter to Obtin High oltge Boost Ability A.hnmugpriy 1, M.Ishwry

More information

Carbon Composition Resistors

Carbon Composition Resistors Dimensions Cron Composition Resistors Rtings nd Dimensions Type L Specifiction Limit nd Performnce d D Derting Curve 8 6 4 (/, w) Test procedures, sequence of test, etc., refer to MIL-STD D nd JIS-C-5.

More information

Strength of Bolted Bamboo Laminate Connections

Strength of Bolted Bamboo Laminate Connections Strength of Bolted Bmboo Lminte Connections Shwn PLATT 1 nd Kent A. HARRIES 1, 1 University of Pittsburgh, Civil nd Environmentl Engineering, Pittsburgh, PA USA khrries@pitt.edu Keywords: bmboo, compression,

More information

Static and dynamic back-corona characteristics

Static and dynamic back-corona characteristics Sttic nd dynmic ck-coron chrcteristics Ginluc Bcchieg, Ivo Gllimerti, IRS srl - vi Vigonovese 81-35124 Pdov - Itly (e-mil: cchieg@irswe.it) Véronique Arrondel, Philippe Rizer, Jérôme Lecointre, Michel

More information

5 I. T cu2. T use in modem computing systems, it is desirable to. A Comparison of Half-Bridge Resonant Converter Topologies

5 I. T cu2. T use in modem computing systems, it is desirable to. A Comparison of Half-Bridge Resonant Converter Topologies 74 EEE TRANSACTONS ON POER ELECTRONCS, VOL. 3, NO. 2, APRL 988 A Comprison of Hlf-Bridge Resonnt Converter Topologies Abstrct-The hlf-bridge series-resonnt, prllel-resonnt, nd combintion series-prllel

More information

Multi-beam antennas in a broadband wireless access system

Multi-beam antennas in a broadband wireless access system Multi-em ntenns in rodnd wireless ccess system Ulrik Engström, Mrtin Johnsson, nders Derneryd nd jörn Johnnisson ntenn Reserch Center Ericsson Reserch Ericsson SE-4 84 Mölndl Sweden E-mil: ulrik.engstrom@ericsson.com,

More information

Lecture 20. Intro to line integrals. Dan Nichols MATH 233, Spring 2018 University of Massachusetts.

Lecture 20. Intro to line integrals. Dan Nichols MATH 233, Spring 2018 University of Massachusetts. Lecture 2 Intro to line integrls Dn Nichols nichols@mth.umss.edu MATH 233, Spring 218 University of Msschusetts April 12, 218 (2) onservtive vector fields We wnt to determine if F P (x, y), Q(x, y) is

More information

METHOD OF LOCATION USING SIGNALS OF UNKNOWN ORIGIN. Inventor: Brian L. Baskin

METHOD OF LOCATION USING SIGNALS OF UNKNOWN ORIGIN. Inventor: Brian L. Baskin METHOD OF LOCATION USING SIGNALS OF UNKNOWN ORIGIN Inventor: Brin L. Bskin 1 ABSTRACT The present invention encompsses method of loction comprising: using plurlity of signl trnsceivers to receive one or

More information

Kirchhoff s Rules. Kirchhoff s Laws. Kirchhoff s Rules. Kirchhoff s Laws. Practice. Understanding SPH4UW. Kirchhoff s Voltage Rule (KVR):

Kirchhoff s Rules. Kirchhoff s Laws. Kirchhoff s Rules. Kirchhoff s Laws. Practice. Understanding SPH4UW. Kirchhoff s Voltage Rule (KVR): SPH4UW Kirchhoff s ules Kirchhoff s oltge ule (K): Sum of voltge drops round loop is zero. Kirchhoff s Lws Kirchhoff s Current ule (KC): Current going in equls current coming out. Kirchhoff s ules etween

More information

Passive and Active Hybrid Integrated EMI Filters

Passive and Active Hybrid Integrated EMI Filters Pssive nd Active Hybrid Integrted EMI Filters J. Biel, A. Wirthmueller, R. Wespe, M.. Heldwein, J. W. Kolr Power Electronic Systems bortory Swiss Federl Institute of Technology Zurich, Switzerlnd Emil:

More information

A Novel Back EMF Zero Crossing Detection of Brushless DC Motor Based on PWM

A Novel Back EMF Zero Crossing Detection of Brushless DC Motor Based on PWM A ovel Bck EMF Zero Crossing Detection of Brushless DC Motor Bsed on PWM Zhu Bo-peng Wei Hi-feng School of Electricl nd Informtion, Jingsu niversity of Science nd Technology, Zhenjing 1003 Chin) Abstrct:

More information

TP Series - Triple PV Top of Pole Solar LED Lighting System

TP Series - Triple PV Top of Pole Solar LED Lighting System TP Series - Triple PV Top of Pole Solr LED Lighting System Instlltion Mnul MKTG-TP34-02-EN-1113 Instlltion Mnul TP Series Importnt Notes nd Wrnings This instlltion nd instruction mnul provides instlltion

More information

PB-735 HD DP. Industrial Line. Automatic punch and bind machine for books and calendars

PB-735 HD DP. Industrial Line. Automatic punch and bind machine for books and calendars PB-735 HD DP Automtic punch nd bind mchine for books nd clendrs A further step for the utomtion of double loop binding. A clever nd flexible mchine ble to punch nd bind in line up to 9/16. Using the best

More information

Research on ultrasonic non-destructive examination in water immersion of a composite material

Research on ultrasonic non-destructive examination in water immersion of a composite material Reserch on ultrsonic non-destructive exmintion in wter immersion of composite mteril AMZA GHEORGHE, VINTILĂ (MIHAIL) SIMONA, ACHIM VERONICA, OANA ELENA AMZA, MIRCEA DOBRE Mteril nd Welding Technology,

More information

Discontinued AN6262N, AN6263N. (planed maintenance type, maintenance type, planed discontinued typed, discontinued type)

Discontinued AN6262N, AN6263N. (planed maintenance type, maintenance type, planed discontinued typed, discontinued type) ICs for Cssette, Cssette Deck ANN, ANN Puse Detection s of Rdio Cssette, Cssette Deck Overview The ANN nd the ANN re the puse detection integrted circuits which select the progrm on the cssette tpe. In

More information

Fitting & User Instructions

Fitting & User Instructions Issue 03 Alexnder Universl Furniture Risers Note: These frmes require the ddition of n ttchment. (See pges 4 - ) Bse Frme Mrk Bse Frme Mrk Fitting & User Instructions These instructions pply to the rising

More information

Experiment 3: The research of Thevenin theorem

Experiment 3: The research of Thevenin theorem Experiment 3: The reserch of Thevenin theorem 1. Purpose ) Vlidte Thevenin theorem; ) Mster the methods to mesure the equivlent prmeters of liner twoterminl ctive. c) Study the conditions of the mximum

More information

* TURNING SPACE ROLLED CURB SIDEWALK RAMP TYPE R (ROLLED SIDES) * TURNING SPACE ** RAMP

* TURNING SPACE ROLLED CURB SIDEWALK RAMP TYPE R (ROLLED SIDES) * TURNING SPACE ** RAMP * MXIMUM TURNING SPCE IS 2.0% IN ECH DIRECTION OF TRVEL. MINIMUM DIMENSIONS 5' x 5'. SEE NOTES. ** MXIMUM RMP CROSS IS 2.0%, RUNNING 5% - 7% (8.3% MXIMUM). SEE NOTES. "NON-WLKING" RE * TURNING SPCE 24"

More information

Lecture 16: Four Quadrant operation of DC Drive (or) TYPE E Four Quadrant chopper Fed Drive: Operation

Lecture 16: Four Quadrant operation of DC Drive (or) TYPE E Four Quadrant chopper Fed Drive: Operation Lecture 16: Four Qudrnt opertion of DC Drive (or) TYPE E Four Qudrnt chopper Fed Drive: Opertion The rmture current I is either positive or negtive (flow in to or wy from rmture) the rmture voltge is lso

More information

Compared to generators DC MOTORS. Back e.m.f. Back e.m.f. Example. Example. The construction of a d.c. motor is the same as a d.c. generator.

Compared to generators DC MOTORS. Back e.m.f. Back e.m.f. Example. Example. The construction of a d.c. motor is the same as a d.c. generator. Compred to genertors DC MOTORS Prepred by Engr. JP Timol Reference: Electricl nd Electronic Principles nd Technology The construction of d.c. motor is the sme s d.c. genertor. the generted e.m.f. is less

More information

OPERATING INSTRUCTION

OPERATING INSTRUCTION -2 AUTOMATIC POLARIMETER OPERATING INSTRUCTION Plese red through these operting instruction before using MRC.VER.01-. CONTENTS I. APPLICATIONS.1 II. III. IV. PERFORMANCE 1 CONSTRUCTION AND PRINCIPLE 2

More information

ET 51 EXTERIOR ROOF DRIP SIDE FINISH MOULDING INSTALLATION

ET 51 EXTERIOR ROOF DRIP SIDE FINISH MOULDING INSTALLATION EXTERIOR ROOF DRIP SIDE FINISH MOULDING 51 INSTALLATION The procedure descried elow is for the LH side. Use the sme procedure for oth the RH nd LH sides, unless otherwise specified. 1. INSTALL ROOF SIDE

More information

PRACTICE NO. PT-TE-1414 RELIABILITY PAGE 1 OF 6 PRACTICES ELECTROSTATIC DISCHARGE (ESD) TEST PRACTICES

PRACTICE NO. PT-TE-1414 RELIABILITY PAGE 1 OF 6 PRACTICES ELECTROSTATIC DISCHARGE (ESD) TEST PRACTICES PREFERRED PRACTICE NO. PT-TE-1414 RELIABILITY PAGE 1 OF 6 ELECTROSTATIC DISCHARGE (ESD) TEST Prctice: Test stellites for the ility to survive the effects of electrosttic dischrges (ESDs) cused y spce chrging

More information

Effect of High-speed Milling tool path strategies on the surface roughness of Stavax ESR mold insert machining

Effect of High-speed Milling tool path strategies on the surface roughness of Stavax ESR mold insert machining IOP Conference Series: Mterils Science nd Engineering PAPER OPEN ACCESS Effect of High-speed Milling tool pth strtegies on the surfce roughness of Stvx ESR mold insert mchining Relted content - Reserch

More information

Analysis of Pre-tension Level upon Biaxial Behaviour of Fused Systems

Analysis of Pre-tension Level upon Biaxial Behaviour of Fused Systems ISSN 1392 1320 MATERIALS SCIENCE (MEDŽIAGOTYRA). Vol. 21, No. 2. 2015 Anlysis of Pre-tension Level upon Bixil Behviour of Fused Systems Dont ZUBAUSKIENE, Eugenij STRAZDIENE, Virginijus URBELIS Deprtment

More information

(1) Non-linear system

(1) Non-linear system Liner vs. non-liner systems in impednce mesurements I INTRODUCTION Electrochemicl Impednce Spectroscopy (EIS) is n interesting tool devoted to the study of liner systems. However, electrochemicl systems

More information

Pavos Series - Small Aperture ( 5mm) nm Faraday Rotators and Isolators

Pavos Series - Small Aperture ( 5mm) nm Faraday Rotators and Isolators Trnsmission (%) Isoltion (db) Trnsmission (%) Isoltion (db) Benefits: Pvos Series - Smll Aperture ( 5mm) 1010-1080nm Frdy Rottors nd Isoltors EOT s Pvos Series Frdy Rottors rotte the plne of polrized light

More information

Investigation of Miter Corner Joint Strength of Case Furniture from Particleboard

Investigation of Miter Corner Joint Strength of Case Furniture from Particleboard ISSN 1392 1320 MATERIALS SCIENCE (MEDŽIAGOTYRA). Vol. 18, No. 4. 2012 Investigtion of Miter Corner Joint Strength of Cse Furniture from Prticleord Vlds NORVYDAS, Antns BALTRUŠAITIS, Ing JUODEIKIENö Deprtment

More information

Incremental encoders Solid shaft with clamping or synchro flange pulses per revolution

Incremental encoders Solid shaft with clamping or synchro flange pulses per revolution Incrementl encoders Solid shft with clmping or synchro flnge 0 5000 pulses per revolution ExEIL580 - solid shft Fetures Size mm Precise opticl sensing Output signl level TTL or HTL Clmping or synchro flnge

More information

Robustness Analysis of Pulse Width Modulation Control of Motor Speed

Robustness Analysis of Pulse Width Modulation Control of Motor Speed Proceedings of the World Congress on Engineering nd Computer Science 2007 WCECS 2007, October 24-26, 2007, Sn Frncisco, USA obustness Anlysis of Pulse Width Modultion Control of Motor Speed Wei Zhn Abstrct

More information

Application Note. Differential Amplifier

Application Note. Differential Amplifier Appliction Note AN367 Differentil Amplifier Author: Dve n Ess Associted Project: Yes Associted Prt Fmily: CY8C9x66, CY8C7x43, CY8C4x3A PSoC Designer ersion: 4. SP3 Abstrct For mny sensing pplictions, desirble

More information

Understanding Basic Analog Ideal Op Amps

Understanding Basic Analog Ideal Op Amps Appliction Report SLAA068A - April 2000 Understnding Bsic Anlog Idel Op Amps Ron Mncini Mixed Signl Products ABSTRACT This ppliction report develops the equtions for the idel opertionl mplifier (op mp).

More information

2005 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media,

2005 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, 005 IEEE. Personl use of this mteril is permitted. Permission from IEEE must be obtined for ll other uses, in ny current or future medi, including reprinting/republishing this mteril for dvertising or

More information

Safety Relay Unit. Main contacts Auxiliary contact Number of input channels Rated voltage Model Category. possible 24 VAC/VDC G9SA-501.

Safety Relay Unit. Main contacts Auxiliary contact Number of input channels Rated voltage Model Category. possible 24 VAC/VDC G9SA-501. Sfety Rely Unit The Series Offers Complete Line-up of Compct Units. Four kinds of -mm wide Units re ville: A -pole model, -pole model, nd models with poles nd OFF-dely poles, s well s Two-hnd ler. Simple

More information

CHARACTERISTICS OF THE GPS SIGNAL SCINTILLATIONS DURING IONOSPHERIC IRREGULARITIES AND THEIR EFFECTS OVER THE GPS SYSTEM

CHARACTERISTICS OF THE GPS SIGNAL SCINTILLATIONS DURING IONOSPHERIC IRREGULARITIES AND THEIR EFFECTS OVER THE GPS SYSTEM CHRCTERISTICS OF THE GPS SIGNL SCINTILLTIONS DURING IONOSPHERIC IRREGULRITIES ND THEIR EFFECTS OVER THE GPS SYSTEM Eurico R. de Paula, I.J.Kantor, L.F.C. de Rezende ERONOMY DIVISION NTIONL INSTITUTE FOR

More information

Rectangular type APS-10 to 15 Series

Rectangular type APS-10 to 15 Series Rectngulr type APS- to 15 Series From n ultr-thin design to n operting distnce of 15 mm, wide-rnging rectngulr types re vilble to meet diversified requirements. Types output type/dc 3-wire type Shpe Operting

More information

Radiant systems 0801EN March 2016 Radiant plasterboard ceiling and/or floor system ISO /7

Radiant systems 0801EN March 2016 Radiant plasterboard ceiling and/or floor system ISO /7 RADIANT CEILING SYSTEM Description is rdint ceiling/wll system relized with 600x1200 mm EPS200 preformed pnels coted with 0,3 mm luminium thermo-conductor sheets, where the plstic pipe with n externl Ø

More information

CAL. NX15 DUO-DISPLAY QUARTZ

CAL. NX15 DUO-DISPLAY QUARTZ L. NX15 UO-ISPLY QURTZ l nlogue time disply l igitl time nd clendr l hronogrph l Tchymeter l t recll function l lrm l Illuminting light (Electroluminescent pnel) ENGLISH Illuminting light (TIME/LENR mode

More information

Electrically Large Zero-Phase-Shift Metamaterial-based Grid Array Antenna for UHF Near-Field RFID Readers

Electrically Large Zero-Phase-Shift Metamaterial-based Grid Array Antenna for UHF Near-Field RFID Readers Electriclly Lrge Zero-Phse-Shift Metmteril-bsed Grid Arry Antenn for UHF Ner-Field RFID Reders Jin Shi, Xinming Qing, member IEEE, Zhi Ning Chen, Fellow, IEEE Abstrct A grid rry ntenn using zero-phse-shift

More information

Two-layer slotted-waveguide antenna array with broad reflection/gain bandwidth at millimetre-wave frequencies

Two-layer slotted-waveguide antenna array with broad reflection/gain bandwidth at millimetre-wave frequencies Two-lyer slotted-wveguide ntenn rry with rod reflection/gin ndwidth t millimetre-wve frequencies S.-S. Oh, J.-W. Lee, M.-S. Song nd Y.-S. Kim Astrct: A 24 24 slotted-wveguide rry ntenn is presented in

More information

PARAMETERS INFLUENCING THE QUALITY OF GROUT IN HOLLOW CLAY MASONRY

PARAMETERS INFLUENCING THE QUALITY OF GROUT IN HOLLOW CLAY MASONRY PARAMETERS INFLUENCING THE QUALITY OF GROUT IN HOLLOW CLAY MASONRY G.R. KINGSLEY, Former Reserch Assistnt University of Colordo, Boulder, USA L. G. TULIN, Professor of Civil Engineering University of Colordo,

More information

Extremely small "footprint" and the highest circuit density available AK550. Front Wire Entry

Extremely small footprint and the highest circuit density available AK550. Front Wire Entry FIXED PRINTED CIRCUIT Tubulr Screw Clmp For use when stndrd size printed circuit terminl blocks re too lrge for vilble spce or where very smll circuit bord is utilized. Our new subminiture design offers

More information

Spiral Tilings with C-curves

Spiral Tilings with C-curves Spirl Tilings with -curves Using ombintorics to Augment Trdition hris K. Plmer 19 North Albny Avenue hicgo, Illinois, 0 chris@shdowfolds.com www.shdowfolds.com Abstrct Spirl tilings used by rtisns through

More information

NP10 DIGITAL MULTIMETER Functions and features of the multimeter:

NP10 DIGITAL MULTIMETER Functions and features of the multimeter: NP10 DIGITL MULTIMETER. unctions nd fetures of the multimeter: 1000 V CT III tri requencies from 10.00...10 M. Diode mesurement nd continuity testing. HOLD mesurement. Reltive mesurement. Duty cycle (%)

More information

Soft switched DC-DC PWM Converters

Soft switched DC-DC PWM Converters Soft switched DC-DC PWM Converters Mr.M. Prthp Rju (), Dr. A. Jy Lkshmi () Abstrct This pper presents n upgrded soft switching technique- zero current trnsition (ZCT), which gives better turn off chrcteristics

More information

Algorithms for Memory Hierarchies Lecture 14

Algorithms for Memory Hierarchies Lecture 14 Algorithms for emory Hierrchies Lecture 4 Lecturer: Nodri Sitchinv Scribe: ichel Hmnn Prllelism nd Cche Obliviousness The combintion of prllelism nd cche obliviousness is n ongoing topic of reserch, in

More information

Reversible and Proportional Electric Actuators

Reversible and Proportional Electric Actuators Reversible nd Proportionl Electric s The MP s re used for two-position, floting, nd proportionl control of dmpers, vlves, nd progrm switches in heting, ventiltion, nd ir conditioning pplictions or similr

More information

Study on SLT calibration method of 2-port waveguide DUT

Study on SLT calibration method of 2-port waveguide DUT Interntionl Conference on Advnced Electronic cience nd Technology (AET 206) tudy on LT clibrtion method of 2-port wveguide DUT Wenqing Luo, Anyong Hu, Ki Liu nd Xi Chen chool of Electronics nd Informtion

More information

Joanna Towler, Roading Engineer, Professional Services, NZTA National Office Dave Bates, Operations Manager, NZTA National Office

Joanna Towler, Roading Engineer, Professional Services, NZTA National Office Dave Bates, Operations Manager, NZTA National Office . TECHNICA MEMOANDM To Cc repred By Endorsed By NZTA Network Mngement Consultnts nd Contrctors NZTA egionl Opertions Mngers nd Are Mngers Dve Btes, Opertions Mnger, NZTA Ntionl Office Jonn Towler, oding

More information

MFAH. Minimizes Burrs for High Quality Machining Results. Low Cutting Force Design

MFAH. Minimizes Burrs for High Quality Machining Results. Low Cutting Force Design igh fficiency Milling Cutter for Finishing Aluminum MFA igh fficiency Milling Cutter for Finishing Aluminum MFA NW CG Imge Low Cutting Force Minimizes Burrs nd Chipping for igh Qulity Mchining Results

More information

The Influence of the Properties of Embroidery Threads on Buckling of Fabric Inside of the Embroidered Element

The Influence of the Properties of Embroidery Threads on Buckling of Fabric Inside of the Embroidered Element ISSN 1392 1320 MATERIALS SCIENCE (MEDŽIAGOTYRA). Vol. 18, No. 4. 2012 The Influence of the Properties of Emroidery Threds on Buckling of Fric Inside of the Emroidered Element Svetln RADAVIČIENĖ 1, Mild

More information

AN ELECTRON SWITCH. by C. DORSMAN and S. L. de BRUIN.

AN ELECTRON SWITCH. by C. DORSMAN and S. L. de BRUIN. SEPTEMBER 1939 267 AN ELECTRON SWITCH y C. DORSMAN nd S. L. de BRUIN. 621.317.755.06 An pprtus is descried with which the time function of two different mgnitudes cn e oserved simultneouslyon the fluorescent

More information

POWER PANEL INSULATION TEST

POWER PANEL INSULATION TEST POWER PNEL INSULTION TEST 1 VOLTGE MPCITY PNEL WITHSTND RTING MIN MLO NO. FEEDER BREKERS NO. FEEDER DISCONNECTS FED FROM OF LODS EQUIPMENT TEMPERTURE TEMPERTURE CORRECTION FCTOR TO, TCF TEST VOLTGE kvdc

More information

Redundancy Data Elimination Scheme Based on Stitching Technique in Image Senor Networks

Redundancy Data Elimination Scheme Based on Stitching Technique in Image Senor Networks Sensors & Trnsducers 204 by IFSA Publishing, S. L. http://www.sensorsportl.com Redundncy Dt Elimintion Scheme Bsed on Stitching Technique in Imge Senor Networks hunling Tng hongqing Technology nd Business

More information

Innovative plate solutions for flexographic printing. nyloflex printing plates

Innovative plate solutions for flexographic printing. nyloflex printing plates Innovtive plte solutions for flexogrphic printing nyloflex printing pltes nyloflex Printing Pltes Unique nd comprehensive expertise in flexogrphic printing Printing pltes from Flint Group to meet every

More information

Investigation of propagation of partial discharges in power transformers and techniques for locating the discharge

Investigation of propagation of partial discharges in power transformers and techniques for locating the discharge Investigtion of propgtion of prtil dischrges in power trnsformers nd techniques for locting the dischrge S.N. Hettiwtte, Z.D. Wng nd P.A. Crossley Astrct: The loction of prtil dischrges in power trnsformer

More information

Series AE W PFC INDUSTRIAL POWER SUPPLY

Series AE W PFC INDUSTRIAL POWER SUPPLY FEATURES Progrmmle output voltge (0%~05%) Progrmmle output current (0%~05%) Universl AC input / Full rnge Constnt current limiting Optionl glol control vi RS3 Selectle +5V / 0.5A or +9V / 0.3A uxiliry

More information

Math Circles Finite Automata Question Sheet 3 (Solutions)

Math Circles Finite Automata Question Sheet 3 (Solutions) Mth Circles Finite Automt Question Sheet 3 (Solutions) Nickols Rollick nrollick@uwterloo.c Novemer 2, 28 Note: These solutions my give you the nswers to ll the prolems, ut they usully won t tell you how

More information

Comparison of High Power Non-Isolated Multilevel DC-DC Converters for Medium-Voltage Battery Storage Applications

Comparison of High Power Non-Isolated Multilevel DC-DC Converters for Medium-Voltage Battery Storage Applications Comprison of High Power NonIsolted Multilevel DCDC Converters for MediumVoltge Bttery Storge Applictions M. Stojdinovic nd J. Biel Lbortory for High Power Electronic Systems ETH Zurich, Physikstrsse 3,

More information