Installation and Care Instructions: Rear Windshield - CFMOTO UForce 800

Size: px
Start display at page:

Download "Installation and Care Instructions: Rear Windshield - CFMOTO UForce 800"

Transcription

1 Installation and Care Instructions: Rear Windshield - CFMOTO UForce 800 *** DO NOT REMOVE PROTECTIVE LAYER FROM THE WINDSHIELD AT THIS TIME. THIS SHOULD BE YOUR LAST AND FINAL INSTALLATION STEP AS WINDSHIELD CAN NOT BE RETURNED ONCE THE PROTECTIVE LAYER IS FULLY REMOVED. *** CONTENTS QUANTITY SIZE DESCRIPTION/PLACEMENT 2 REAR LEXAN WINDSHIELD (UPPER SECTION AND LOWER SECTION) 1 LOWER CANVAS PANEL 5 2 X 12 GECKO STRAPS - MOUNTS WINDSHIELD TO REAR ROLL BARS 1 INSTALLATION HARDWARE KIT 1 ADHESIVE HOOK KIT 1 INSTALLATION AND CARE INSTRUCTIONS Step 1: Inspect box to make sure there are no holes or damage from shipping. If damaged, please call your authorized Octane Ridge dealer for further instructions. Step 2: Remove the roof of your UForce and any existing roll bar hardware from your vehicle that will interfere with the installation. Step 3: Remove your Octane Ridge Rear Windshield contents from the shipping box. Hold each section of windshield up to the roll bars of your machine to ensure you received the correct windshield. Step 4: Before peeling off the protective layer, thoroughly inspect each side of the windshield for any visible scratches or defects. Set windshield aside. Step 5: Pull both seatbelts out enough to where you can place around the seats and out of the way during installation. Step 6: Take the supplied adhesive Velcro hook strip and cut into the following sizes: Two (2) 17-inch strips One (1) 14.5-inch strip Four (4) 5-inch strips Step 7: Attach one (1) 17-inch adhesive strip along each side of the lower horizontal crossbars behind each seat. Make sure the outer edge of the strips set to the inside of the vertical roll bar weld as shown below.

2 Step 8: Place one (1) 5-inch adhesive strip on each side of the rear vertical roll bars just above the same weld mentioned in Step 7 and wrap around roll bar as shown below. Step 9: Raise the dump bed of the UForce before continuing to the next step. Step 10: Remove upper screw from each outer side panel as shown below. Step 11: Place the remaining 5-inch adhesive strips on the vertical roll bar behind side panel directly above bolt bracket. Step 12: Attach the 14.5-inch adhesive strip horizontally behind the driver seat along the bottom edge of the box. There should be approximately one-inch on each side that will wrap around the sides of the box as shown below.

3 Step 13: Center the lower canvas panel and pull tightly across back of machine, this may require some assistance. The upper straps on the canvas panel should sit just above the weld on the vertical roll bar mentioned in Step 7. Secure straps tightly around roll bar, first attaching the outer strap, then overlapping with the interior strap. Always pull canvas tight between each attachment point. Finally, attach the upper part of the canvas to the horizontal crossbars behind each seat as shown below. Step 14: Attach the lower straps on the canvas panel in the same manner, wrapping the outer strap around the roll bar first, then overlapping with the interior strap as shown below. Step 15: Secure the lower section on the canvas panel along the bottom edge of the box behind driver seat as shown below. Step 16: The canvas panel should sit straight and snug once attached correctly. Lower dump bed of UForce to its normal position and check clearance. Step 17: Place the supplied clamps around the center section of the roll bars with the flat side facing the exterior of the machine and the bolt holes towards the center of the bars. Do not attach bolts at this time. See photo below. Step 18: 18: You may now peel the the protective layer back just just far enough far enough to expose on each th windshield. section See slot to expose the locations holes to connect below. sections together. Step 19: Using supplied installation hardware kit, take four (4) neoprene washers, four (4) hex bolts, four (4) flat washers and four (4) nuts and attach the two windshield sections by placing the upper section of the windshield over the lower section and align the holes. Slide the neoprene washers onto each hex bolt and place bolts through the outside of the panel and through the holes. Insert the flat washer onto the bolt, apply the nuts onto each bolt and tighten completely. See photos on next page for illustration. Step 20: You may now peel the protective layer back just far enough to expose the outer slots on the connected windshield sections. This will be where the Gecko straps attach windshield to rear roll bars.

4 Step 21: Starting with the top section of the windshield, insert three (3) Gecko straps along the horizontal top roll bar. With the Velcro side facing down, place the pointed end of the strap through the inside of the slot and pull through. Insert the strap through the buckle, making sure the buckle is pushed back underneath the roll bar and as close to the windshield as possible. Secure the Velcro so that the Octane Ridge logo is facing forward and upright. It s important to keep the windshield in the proper position against the roll bar so that the windshield doesn t set too low. Step 22: Insert the remaining two (2) Gecko straps in the slots on the outer sides of the windshield. Step 23: Reposition the clamps to align with the slots in the rear windshield. Slide the neoprene washer onto the hex bolt and place bolt through the back panel and through the clamp. Insert the flat washer, then nut onto the bolt and tighten. Repeat with the other clamp. Step 24: It may be necessary to adjust tightness of each strap to ensure the windshield is positioned correctly and securely. Step 25: You may now remove the remaining protective layer from each side of your windshield, reinstall the roof and installation is complete.

5 PERIODIC CLEANING USING CORRECT PROCEDURES CAN HELP TO PROLONG SERVICE LIFE. FOR CARE AND CLEANING, IT IS RECOMMENDED THAT THE FOLLOWING INSTRUCTIONS BE STRICTLY ADHERED TO. Lexan Cleaning Recommendations Gently wash Lexan with a solution of mild soap and lukewarm water, using a soft, grid- free cloth or sponge to loosen any dirt or grime. Fresh paint splashes, grease and smeared glazing compounds can be removed easily before drying by rubbing lightly with a soft cloth using petroleum ether (BP65), hexane or heptane s. Afterwards, wash the sheet using mild soap and lukewarm water. Scratches and minor abrasions can be minimized by using a mild automobile polish. We suggest that a test be made on a small area of the Lexan sheet with the polish selected and that the polish manufacturer s instructions be followed, prior to using the polish on the entire sheet. Finally, thoroughly rinse with clean water to remove any cleaner residue and dry the surface with a soft cloth to prevent water spotting. Important Instructions Never use abrasive or highly alkaline cleaner on Lexan polycarbonate materials. Never use aromatic or halogenated solvents like toluene, benzene, gasoline, acetone or carbon tetrachloride on Lexan polycarbonate materials. Use of incompatible cleaning materials with Lexan sheet can cause structural and/or surface damage. Contact with harsh solvents such as methyl ethyl ketone (MEK) or hydrochloric acid can result in surface degradation and possible crazing of Lexan sheet. Never scrub with brushes, steel wool or other abrasive materials. Never use squeegees, razorblades or other sharp instruments to remove deposits or spots. Do not clean Lexan polycarbonate in direct sunlight or at high temperatures as this can lead to staining. For all mentioned chemicals consult the manufacturer s material safety datasheet (MSDS) for proper safety precautions. Go to OctaneRidge.com to see more information on this product and others, plus installation videos!

Fitting Instructions

Fitting Instructions Fitting Instructions = Actions. Red = Notes you must read before continuing. Grey = Only applies to canopies over 4m widths. Overview 1. Tools you will need. 2. What you will need to provide. 3. Description

More information

TRX SERIES LIGHTBARS

TRX SERIES LIGHTBARS 3/14/2016 TRX SERIES LIGHTBARS TRX-20 TRX-35 TRX-50 TRX-25 TRX-30 TRX-40 TRX-45 TRX-60 Product Manual TOMAR OFF-ROAD, 2100 W OBISPO AVE, GILBERT, AZ 85233 800-338-2133 www.tomaroff-road.com Wiring Main

More information

Vacant Properties Clear Boarding with SecureView

Vacant Properties Clear Boarding with SecureView Vacant Properties Clear Boarding with SecureView SecureView Product Data Sheet Description: SecureView is an industrial grade sheet material extruded from post-industrial grade recycled polycarbonate

More information

Document: Installation Guide Guide No: 019 Description: Omega Canopy, Free-Standing, Gable-Roof, Type 1

Document: Installation Guide Guide No: 019 Description: Omega Canopy, Free-Standing, Gable-Roof, Type 1 Page 1 of 42 Sections: Section No. Section Description Page No. 01 Essential Tools 2 02 Tools that will make Installation easier 2 03 Items to be supplied by Installer 2 04 Canopy main components 3 05

More information

WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. WARNING. Ranger XP Door Kit

WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. WARNING. Ranger XP Door Kit REVISION 04 November, 20 2018 Ranger XP Door Kit Prior to installation, please verify if a revised version of this instruction sheet is available on Knowledge Center. The following symbols may be used

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS NOTE: Bolts should remain hand tight until all bolts are installed. STEP 1 Installing the door base (both sides). 1. Locate the outer, roll cage, mounting bolt (passenger side is shown in the illustration).

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #

INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD

More information

Vacant Properties Clear Boarding with SecureView

Vacant Properties Clear Boarding with SecureView Vacant Properties Clear Boarding with SecureView TABLE OF CONTENTS Product Data Sheet pages 2 & 3 Cleaning & Graffiti Removal page 4 Order Placement Instructions pages 5 & 6 Window Installation Guide pages

More information

INSTALLATION INSTRUCTIONS 3 BULL BAR 99-04, 04 "HERITAGE" F-150/250LD 2WD, 97-04, 04 "HERITAGE" 4WD WD EXPEDITION/ WD EXPEDITION PART

INSTALLATION INSTRUCTIONS 3 BULL BAR 99-04, 04 HERITAGE F-150/250LD 2WD, 97-04, 04 HERITAGE 4WD WD EXPEDITION/ WD EXPEDITION PART INSTALLATION INSTRUCTIONS 3 BULL BAR PART #B-F1971;B-F2971 PARTS LIST: 1 Bull Bar 2 12-1.75mm x 130mm x 40mm Hex Bolts 1 Driver/Left Mounting Bracket 4 12-1.75mm x 35mm Hex Bolts 1 Passenger/Right Mounting

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS SG57f GENUINE PARTS INSTALLATION INSTRUCTIONS. DESCRIPTION: Sunroof Wind Deflector. APPLICATION: Pathfinder; Frontier with no roof rails 3. PART NUMBER: 999D4-XR00 4. KIT CONTENTS: Item No. ) ) 3) 4) 5)

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2

INSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2 INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS FOR 07-13 CHEVY SILVERADO 1500 PART#RU-CHSI07-B PARTS LIST: 1 Main Body 28 12mm x 37mm OD x 3mm Large Flat Washers 1 Driver/Left Brush Guard 8 12-1.75mm x 40mm

More information

WEAR SAFETY GLASSES WHEN INSTALLING THIS KIT.

WEAR SAFETY GLASSES WHEN INSTALLING THIS KIT. INSTALLATION INSTRUCTIONS Trans4mer Mounting Systems Part No. 29753 (black) Part No. 65654 (stainless) for full size GM pickups, and Blazer, Yukon, Suburban, Tahoe As you read these instructions, you will

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS PART#: 17A110200MSS\17A110200MA MODULAR GRILL GUARD FOR NISSAN FRONTIER 05-10//PATHFINDER 05-07 1 guard, center section 1 brush guard, left side 1 brush guard,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 6334 For Chevrolet Silverado 500HD & 3500 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of looks,

More information

(2) 25mm x 20mm x 5mm Adhesive Backed Foam Pads. 100mm x 50mm x 1.0mm Adhesive Backed Foam. (2) Spacer Plates. Passenger/Right Side Frame Mounting

(2) 25mm x 20mm x 5mm Adhesive Backed Foam Pads. 100mm x 50mm x 1.0mm Adhesive Backed Foam. (2) Spacer Plates. Passenger/Right Side Frame Mounting PARTS LIST: 1 Grille Guard 10 12mm Lock Washers 1 Driver/Left Frame Mounting 16 12mm x 32mm OD x 3mm Flat Washers 1 Passenger/Right Frame Mounting 8 12mm Hex Nuts 1 Driver/Left Side Top Support 2 10-1.50mm

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Mounting System Dodge Ram Kit No. 65220, 73132, 75525, 76253 (black) or 65221, 73133, 75530, 76254 (stainless) As you read these instructions, you will see NOTES, CAUTIONS

More information

Slide the stock rubber tank mount caps onto the ends of the CS-1 tank mount:

Slide the stock rubber tank mount caps onto the ends of the CS-1 tank mount: RYCA CS-1 BODY PARTS INSTALLATION GUIDE [The CS-1 installation guides should be used as supplements to the videos found on our Youtube Channel. There is no strict order to the build process, but it is

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 7646 & 766 For GMC Sierra 500 As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message has a specific purpose.

More information

UPPER DOOR KIT P/N APPLICATION BEFORE YOU BEGIN ITEMS MARKED (*) ARE INCLUDED IN HARDWARE KIT PN P/N Rev 01 07/14 Page 1 of 6

UPPER DOOR KIT P/N APPLICATION BEFORE YOU BEGIN ITEMS MARKED (*) ARE INCLUDED IN HARDWARE KIT PN P/N Rev 01 07/14 Page 1 of 6 UPPER DOOR KIT P/N 2880609 APPLICATION RZR 900 BEFORE YOU BEGIN Read these instructions thoroughly and make sure all parts and tools are accounted for. Please retain these installation instructions for

More information

Be sure any accessory used will fit with the soft upper doors before installing. Not all accessories will be compatible.

Be sure any accessory used will fit with the soft upper doors before installing. Not all accessories will be compatible. Company Name: Spike Power Sports Vehicle Name: Polaris General 2P Product Description: Soft Upper Doors Part Number: 58-1600 Revision: R01 09/19/2018 Contents: 655 Elm Ridge Ave, Canal Fulton OH, 44614

More information

INSTALLATION INSTRUCTIONS SIDE BAR FORD ESCAPE & MAZDA TRIBUTE PART #

INSTALLATION INSTRUCTIONS SIDE BAR FORD ESCAPE & MAZDA TRIBUTE PART # INSTALLATION INSTRUCTIONS SIDE BAR 2008-2010 FORD ESCAPE & MAZDA TRIBUTE PART # 50136 50137 PARTS LIST: 1 Driver/Left Sidebar 2 10-1.50mm x 35mm Bolt Plate 1 Passenger/Right Sidebar 2 10-1.50mm x 30mm

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS PLATINUM 4 OVAL STEP BAR (90 BENT END) APPLICATION: 2010-2015 Dodge Ram 2500/3500 Mega Cab PART NUMBER: 21-3570, 21-3575, 23-3570, 23-3575, 25-3570, 25-3575,

More information

INSTALLATION INSTRUCTIONS 3"/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ

INSTALLATION INSTRUCTIONS 3/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ INSTALLATION INSTRUCTIONS 09-12 FORD F-150 SUPERCREW PART # DZ 372697/DZ 372699 PARTS LIST: 1 Driver/Left Sidebar 4 1/2 Lock Washers 1 Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting

More information

Kawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions.

Kawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Owner s Manual Model: Kawasaki Teryx 750 Kawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Safety Instructions Cab Kit Contents Hardware

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 76139 & 7643 For Chevrolet Silverado 1500 As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message has a

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 6367 For Chevrolet Silverado 1500, Suburban 1500 and Tahoe As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each

More information

(2) 12mm x 40mm Bolt Plate (long) pictured w/plastic retainer. (6) 12mm x 40mm Bolt Plate (short) Support Bracket Driver/left Front

(2) 12mm x 40mm Bolt Plate (long) pictured w/plastic retainer. (6) 12mm x 40mm Bolt Plate (short) Support Bracket Driver/left Front PARTS LIST: 1 Driver/left Running Board w-1 Backing 8 12mm Plastic Retainers 1 Passenger/right Running Board w-1 Backing 8 12mm x 32mm x 3mm Flat Washers 2 2 inch tall rubber backing (SX & Limited only)

More information

INSTALLATION INSTRUCTIONS 3 ROUND & 4 OVAL SIDEBAR (90-DEG BENT END) DODGE RAM MEGA CAB PART NUMBER SB1214S SB1214B

INSTALLATION INSTRUCTIONS 3 ROUND & 4 OVAL SIDEBAR (90-DEG BENT END) DODGE RAM MEGA CAB PART NUMBER SB1214S SB1214B INSTALLATION INSTRUCTIONS PART NUMBER SB1214S SB1214B PARTS LIST: Qty Description Qty Description 1 Driver/Left Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Passenger/Right Sidebar 4 12mm Lock Washers

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For 2007 Chevrolet Silverado 1500 and GMC Sierra 1500 Kit 75230 (Black) and 76007 (Stainless) Your safety, and the safety of others, is very

More information

INSTALLATION INSTRUCTIONS JEEP SCRAMBLER FAST TRAC TOP PART #108-21X

INSTALLATION INSTRUCTIONS JEEP SCRAMBLER FAST TRAC TOP PART #108-21X INSTALLATION INSTRUCTIONS JEEP SCRAMBLER FAST TRAC TOP PART #108-21X Thank you for purchasing Specialty s Convertible Top for your Jeep vehicle. It has been designed for great fit and long wear. Please

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 63470 For Ford 4x4 F150, F250 Light Duty & Expedition As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS. Each message

More information

Driver/Left Top. Support Bracket

Driver/Left Top. Support Bracket PARTS LIST: 1 Grille Guard 8 10mm Lock Washers 1 Driver/Left Frame Bracket 8 10mm Hex Nuts 1 Passenger/Right Frame Bracket 2 8-1.25mm x 25mm Button Head Bolts 1 Driver/Left Bottom Support Bracket 2 8mm

More information

FENDER FLARE INSTALLATION

FENDER FLARE INSTALLATION Customer Support TM FENDER FLARE INSTALLATION TG-FF8C4108 IMPORTANT TYGER only approves the installation according to our instructions with the hardware provided. WARNING Failure to complete the installation

More information

INSTALLATION INSTRUCTIONS Scout II - Fast Trac PART #

INSTALLATION INSTRUCTIONS Scout II - Fast Trac PART # INSTALLATION INSTRUCTIONS Scout II - Fast Trac PART #442-210 Thank you for purchasing Specialty s Convertible Top for your Scout vehicle. It has been designed for great fit and long wear. Please read and

More information

XHD Bull Bar w/ Dual Row LED Light Bar (10-17 Jeep JK)

XHD Bull Bar w/ Dual Row LED Light Bar (10-17 Jeep JK) XHD Bull Bar w/ Dual Row LED Light Bar (10-17 Jeep JK) PARTS LIST: 1 Driver/Left Side Bull Bar Upright 8 10-1.5mm Hex Nuts 1 Side Bull Bar Upright 4 10-1.5mm Nylon Lock Nuts 1 Top Cross Bar 2 Light Bar

More information

JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT

JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK001 / KRJW014T INSTALL TIME: 2.5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll

More information

Before returning this product to the store of purchase

Before returning this product to the store of purchase Before returning this product to the store of purchase Contact Dee Zee if you experience the following problems: Missing Parts Installation Problems/Questions Warranty Questions 1.800.779.2102 Hours of

More information

WARNING WARNING. CAUTION Indicates a hazard which, if not. NOTICE Indicates an instruc on which, if not

WARNING WARNING. CAUTION Indicates a hazard which, if not. NOTICE Indicates an instruc on which, if not Prior to installa on, please verify if a revised version of this instruc on sheet is available on Knowledge Center. The following symbols may be used in this document. WARNING Indicates a hazardous situa

More information

Passenger/Right Front Mounting Bracket

Passenger/Right Front Mounting Bracket PARTS LIST: 1 Driver side running board 1 8mm Insert Installation Tool 1 Passenger side running board 4 10-1.50mm x 35mm Hex Bolt 1 Driver 10 10mm x 24mm OD x 2.2mm Flat Washer 1 Passenger 6 10mm Lock

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Gen II Mount System For 2011-2012 Dodge Ram HD 4500/5500 Bracket Kit 90160 Your safety, and the safety of others, is very important. To help you make informed decisions

More information

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED RAMPAGE P R O D U C T S 84 (+/- 1/4 ) INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO 1966-1977 TOOLS REQUIRED 3/8 WRENCH 7/16 WRENCH ½ WRENCH #2 PHILLIPS SCREWDRIVER 1/8 DRILL

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Gen II Mount System For 2008 Ford Super Duty Kit 80140 (Large Frame Black) and Kit 80150 (Mid Frame Black) and Kit 80155 (Mid Frame Stainless) Your safety, and the safety

More information

Bushwacker Jeep Flat Style Fender Flares Front Pair

Bushwacker Jeep Flat Style Fender Flares Front Pair Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:

More information

Installation Instructions. Mesh Grille

Installation Instructions. Mesh Grille Installation Instructions Part Number 81114 I-sheet Rev. A1 Mesh Grille For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to obtain

More information

VIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4

VIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4 PARTS LIST: VIEWPOINT ALUMINUM RUNNING BOARD 1 Driver/Left Running Board 4 10-1.5mm x 50mm T-Bolt 1 Passenger/Right Running Board 12 10mm Plastic Retainers 1 Driver/Left Bracket 2 10-1.50mm x 40mm Hex

More information

TYGER GUARD. Parts List BEFORE INSTALLATION WARNING TG-GD6D /7. Tyger Guard. Tube Brackets (Bull Bar) passenger or driver side

TYGER GUARD. Parts List BEFORE INSTALLATION WARNING TG-GD6D /7. Tyger Guard. Tube Brackets (Bull Bar) passenger or driver side TYGER GUARD TM BEFORE INSTALLATION TG-GD6D60068 READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED. CUTTING IS

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD CHEVY TAHOE / AVALANCHE 1500/ SUBURBAN 1500 PART # /502795

INSTALLATION INSTRUCTIONS GRILLE GUARD CHEVY TAHOE / AVALANCHE 1500/ SUBURBAN 1500 PART # /502795 (W) INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 502794/502795 PARTS LIST: 1 Grille Guard 2 12-1.75mm x 140mm Hex Bolts 2 Frame Mounting Brackets 8 12-1.75mm x 30mm Hex Bolts 2 Lower Support Brackets

More information

JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT

JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK002 / KRJW014T INSTALL TIME: 5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll

More information

UPPER DOOR KIT P/N

UPPER DOOR KIT P/N UPPER DOOR KIT P/N 2879946 Application RZR XP4 1000 Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain these installation instructions

More information

Installation Instructions Yamaha Rhino Soft Cab Enclosure

Installation Instructions Yamaha Rhino Soft Cab Enclosure Installation Instructions Yamaha Rhino Soft Cab Enclosure Vehicle Application Yamaha Rhino 2008 Current Part Number: 20301 www.bestoputv.com - We re here to help! Visit our web site and click on Ask a

More information

8mm x 25mm "Z" Bolt Plates. (2) Tube Spacers. (2) 12mm Bolt Plates w/ Nut

8mm x 25mm Z Bolt Plates. (2) Tube Spacers. (2) 12mm Bolt Plates w/ Nut PARTS LIST: 1 Grille Guard 10 12mm Lock Washers 1 Driver/Left Side Frame Mounting Bracket 8 12mm Hex Nuts 1 Passenger/Right Side Frame Mounting Bracket 2 10-1.50mm x 25mm Button Head Bolts 1 Driver/Left

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS TEL -866-XANATOS INSTALLATION INSTRUCTIONS PART#: 7D5000SS\7D500A GRILL GUARD FOR DODGE SPRINTER 07-09 PARTS LIST: 8 6 Grille Guard Driver/Left Frame Mounting Passenger/Right Frame Mounting Driver/Left

More information

Aeon CLR Series EDGE FREE CLR Fixed Frame Screen w/ StarBright CLR (Ceiling Light Rejecting ) Front Projection Material

Aeon CLR Series EDGE FREE CLR Fixed Frame Screen w/ StarBright CLR (Ceiling Light Rejecting ) Front Projection Material Aeon CLR Series EDGE FREE CLR Fixed Frame Screen w/ StarBright CLR (Ceiling Light Rejecting ) Front Projection Material User s Guide Product Description: The Aeon CLR Series is an ultra-short throw fixed

More information

ELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS. Style A Style B Style C Style D

ELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS. Style A Style B Style C Style D ELEGANCE SHOWER DOOR/ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS BRONCO FAST TRAC TOP PART #331-210 BRONCO 1966-1977 Thank you for purchasing Specialty s Convertible Top for your Bronco. It has been designed for great fit and long wear. Please

More information

Jeep. Flat Style Fender Flares Front Pair Front Part # Rev-9 02/23/2016 For complete fitment info visit :

Jeep. Flat Style Fender Flares Front Pair Front Part # Rev-9 02/23/2016 For complete fitment info visit : STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

INSTALLATION INSTRUCTIONS CJ-5 M38A PART # With Doors

INSTALLATION INSTRUCTIONS CJ-5 M38A PART # With Doors INSTALLATION INSTRUCTIONS CJ-5 M38A1 1955-1975 PART #109-011 With Doors Thank you for purchasing Specialty s Convertible Top for your Jeep vehicle. It has been designed for great fit and long wear. Please

More information

QWALL 5.2 (2 Back Panels)

QWALL 5.2 (2 Back Panels) QWALL 5. ( Back Panels) SHOWER ACRYLIC WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date

More information

IMPORTANT: WILL NOT FIT COUNTRYMAN MODELS

IMPORTANT: WILL NOT FIT COUNTRYMAN MODELS Part #1410-0102-07 2 3 1 IMPORTANT: WILL NOT FIT COUNTRYMAN MODELS Apply masking tape around the bottom grille opening and across the bottom of the upper facto ry grille.. Open the hood and remove the

More information

Optima 450 LED Edge-Lit Single-Sided Light Box. Installation Instructions INSTALLATION INSTRUCTIONS. Figure 1. Tools you ll need

Optima 450 LED Edge-Lit Single-Sided Light Box. Installation Instructions INSTALLATION INSTRUCTIONS. Figure 1. Tools you ll need Installation Instructions Optima 450 LED Edge-Lit Single-Sided Light Box Figure 1 INSTALLATION INSTRUCTIONS Before you begin These instructions illustrate the Stylmark Optima 450 LED Edge-Lit Single-Sided

More information

INSTALLATION INSTRUCTIONS Super Scout PART #

INSTALLATION INSTRUCTIONS Super Scout PART # INSTALLATION INSTRUCTIONS Super Scout 71-80 PART #443-010 Thank you for purchasing Specialty s Convertible Top for your Scout vehicle. It has been designed for great fit and long wear. Please read and

More information

International Scout II

International Scout II International Scout II Tools needed: 9/64 drill bit 1/8 drill bit #2 Philips bit for drill Tape measure Pencil Drill #3 Philips Screwdriver #2 Philips Screwdriver Utility knife Contents: 2 bedrails (2

More information

GRILLE GUARD SPRINTER VAN (EXCLUDES X4) INCLUDES MERCEDES, FREIGHTLINER AND DODGE PARTS LIST:

GRILLE GUARD SPRINTER VAN (EXCLUDES X4) INCLUDES MERCEDES, FREIGHTLINER AND DODGE PARTS LIST: PARTS LIST: 1 Grille Guard 8 12mm Hex Nuts 1 Driver/Left Side Frame Mounting Bracket 2 10-1.50mm x 25mm Button Head Bolts 1 Passenger/Right Side Frame Mounting Bracket 4 10mm x 20mm OD x 2mm Flat Washers

More information

Pickup Box Utility Rack Package Installation (Instruction ID: )

Pickup Box Utility Rack Package Installation (Instruction ID: ) 017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For GMC Sierra 2500HD & 3500, + 03 Kit 76248/76249 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety

More information

Premium Light Filtering Sheer Shade

Premium Light Filtering Sheer Shade Premium Light Filtering Sheer Shade Installation Instructions Email: customerservice@blindster.com Call us: (888) 256-8672 Mon - Fri 8am - 7pm (CT) Congratulations on purchasing a Premium Light Filtering

More information

INSTALLATION INSTRUCTIONS: DISC SANDER SHIELDS UPPER BELT SANDER SHIELDS LOWER BELT SANDER SHIELDS

INSTALLATION INSTRUCTIONS: DISC SANDER SHIELDS UPPER BELT SANDER SHIELDS LOWER BELT SANDER SHIELDS INSTALLATION INSTRUCTIONS: DISC SANDER SHIELDS UPPER BELT SANDER SHIELDS LOWER BELT SANDER SHIELDS Disc Sander s Upper and Lower Belt Sander s 4620 Hydraulic Road Rockford, Illinois 61109 Toll-Free 1-800-922-7533

More information

Flat Style Fender Flares Rear Pair. Jeep. Included in Hardware Kit:

Flat Style Fender Flares Rear Pair. Jeep. Included in Hardware Kit: Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure

More information

Bolt-On/Rugged Fender Flares Ford F150 (15-ON) Please read instructions entirely before installing this product.

Bolt-On/Rugged Fender Flares Ford F150 (15-ON) Please read instructions entirely before installing this product. Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY EXTRUSION 29ft RETAINING CLIP 4 ALLEN KEY BOLT 42 ALCOHOL TOWELETTE 4

More information

Midmark Stainless Steel Cages Setup Manual

Midmark Stainless Steel Cages Setup Manual Midmark Stainless Steel Cages Setup Manual Table of Contents Pre-Installation......................... 2 Parts Identification..................... 2-3 Base Construction....................... 3 Assembly............................

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS FOR 2017-2018 NISSAN TITAN (EXCLUDES TITAN XD MODELS) PART#AB-NI20 PARTS LIST: 1 Bull Bar 2 8mm Nylon Lock Nuts 1 Driver/Left Side Bull Bar Bracket 2 8-1.25mm

More information

KD Table Base Assembly and Top Attachment Instructions

KD Table Base Assembly and Top Attachment Instructions KD Table Base Assembly and Top Attachment Instructions 4011xx 5000xx 7014xx 8001xx 8206xx Congratulations on the purchase of your Tropitone furniture. Read through all steps before starting assembly. CAUTION:

More information

FENDER FLARE INSTALLATION

FENDER FLARE INSTALLATION Part#: TG-FF8G4158 FOR 2007-2013 GMC Sierra 1500 Pickup Truck (Exclude 69.3inch Short Bed Models) FENDER FLARE INSTALLATION Hardware Kit Included IMPORTANT TYGER only approves the installation according

More information

RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS

RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Winch Mount For 2007-2010 Chevrolet Silverado HD and GMC Sierra HD Bracket Kit 90140 Your safety, and the safety of others, is very important. To help you make informed

More information

(2) Plastic Plugs (2) Frame Bracket. Spacers. License Plate Bracket. (2) 12mm Single Bolt Plates. (2) 12mm Double Bolt Plates

(2) Plastic Plugs (2) Frame Bracket. Spacers. License Plate Bracket. (2) 12mm Single Bolt Plates. (2) 12mm Double Bolt Plates LDB-CSIL26-FB PARTS LIST: 1 LD1 Bumper Assembly 10 12mm Hex Nuts 1 Driver/left Frame Mounting 6 10-1.5mm x 35mm Hex Bolts 1 Passenger/right Frame Mounting 12 10mm x 27mm OD x 3mm Flat Washers 2 Spacers

More information

INSTALLATION INSTRUCTIONS RH 412 STEEL DOORS

INSTALLATION INSTRUCTIONS RH 412 STEEL DOORS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job

More information

INSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058

INSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058 INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks

More information

JEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT

JEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT JEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK004 / KRJW016T INSTALL TIME: 2 Hours NOTE: Your Jeep JK (3 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll

More information

3" SIDEBAR CHEVY TRAVERSE/GMC ACADIA/07-10 SATURN OUTLOOK/07-09 BUICK ENCLAVE (EXCL BUICK ENCLAVE)

3 SIDEBAR CHEVY TRAVERSE/GMC ACADIA/07-10 SATURN OUTLOOK/07-09 BUICK ENCLAVE (EXCL BUICK ENCLAVE) PARTS LIST: 1 Driver/Left Sidebar 6 s 1 Passenger/Right Sidebar 6 12mm ID x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting 6 s 1 Passenger/Right Mounting 4 10mm Lock Washers 1 Driver/Left Mounting 4

More information

Included in Hardware Kit. Volkswagen Amarok Pocket Style Fender Flares Set of 4 Set Part # / # Rev-3 02/07/2017

Included in Hardware Kit. Volkswagen Amarok Pocket Style Fender Flares Set of 4 Set Part # / # Rev-3 02/07/2017 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

FreshSesh, PowderHound & Big PowderHound

FreshSesh, PowderHound & Big PowderHound FreshSesh, PowderHound & Big PowderHound Carrier (2x) universal mounting bracket (4x) SkiLift (2x) (mounting bracket parts:) Hex Key with Bolt (2x) SkiLift (2x) Button Head Screw (2x) Hex Wrench (1x) Base

More information

Titan - Double Skin Steel Partitioning. Installation Pack

Titan - Double Skin Steel Partitioning. Installation Pack Titan - Double Skin Steel Partitioning Installation Pack Troax Lee Manufacturing Ltd. Scan me Troax Lee Manufacturing Ltd Telephone : +44 (0) 1384 277 441 Building 52, Third Avenue, Facsimilie : +44 (0)

More information

Jeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-3 1/11/2016

Jeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-3 1/11/2016 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

Ford Pocket Style Fender Flares Set of 4

Ford Pocket Style Fender Flares Set of 4 Ford Pocket Style Fender s Set of 4 STEP 1 PRIOR TO INSTALLATION Set Part #20942-02 Rev-4 07/05/2018 A) Bushwacker only approves installing the flares according to these written instructions with the hardware

More information

INSTALLING YOUR NEW SPRING LIFT ARM KIT

INSTALLING YOUR NEW SPRING LIFT ARM KIT INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as

More information

Mid Size Ranger Pro-fit Doors #06023 Installation & Operations Manual

Mid Size Ranger Pro-fit Doors #06023 Installation & Operations Manual Mid Size Ranger Pro-fit Doors #06023 Installation & Operations Manual Before You Start: Please familiarize yourself with all the steps before beginning assembly. Compatibility Info: This Door System is

More information

Hardware and Components:

Hardware and Components: Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut

More information

WARNING. Failure to observe these instructions could lead to severe injury or death.

WARNING. Failure to observe these instructions could lead to severe injury or death. INSTALLATION INSTRUCTIONS WINCH MOUNTING KIT Part Number: 80156, 80160 Application: 2008 Ford F150 Your safety, and the safety of others, is very important. To help you make informed decisions about safety,

More information

Bolt-On/Rugged Fender Flares Chevy CK PICKUP (88-98) Please read instructions entirely before installing this product.

Bolt-On/Rugged Fender Flares Chevy CK PICKUP (88-98) Please read instructions entirely before installing this product. Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY EXTRUSION 25ft SMALL CLIPS 14 ALLEN KEY BOLT 42 ALCOHOL TOWELETTE 4 SCREWS

More information

Chevy Pocket Style Fender Flares Set of 4

Chevy Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions

More information

10-1.5mm x 40mm Hex Bolt 1 Driver/Left Front Inner Support Bracket (2WD & 4WD Vehicles W/O Skid Plate Only) 2

10-1.5mm x 40mm Hex Bolt 1 Driver/Left Front Inner Support Bracket (2WD & 4WD Vehicles W/O Skid Plate Only) 2 PARTS LIST: 1 Driver/Left sidebar 4 12mm x 32mm OD x 3mm Flat Washer 1 Passenger/Right sidebar 4 12mm x 24mm OD x 2.5mm Flat Washer 1 Driver/Left Mounting Bracket 6 12mm Lock Washers 1 Passenger/Right

More information

QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS

QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS QWALL 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical

More information

Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr)

Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr) Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr) Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Brush Guard Kit Kit no. 67730 (black), 67731 (stainless) for GMC Trucks Your safety, and the safety of others, is very important. To help you make informed decisions about safety,

More information

INSTALLATION INSTRUCTIONS / DODGE RAM CREW CAB 2500/3500

INSTALLATION INSTRUCTIONS / DODGE RAM CREW CAB 2500/3500 INSTALLATION INSTRUCTIONS 225019 / 225019-2 2010 DODGE RAM CREW CAB 2500/3500 PARTS LIST: Qty Description Qty Description 1 Driver/Left Side Bar 4 Plastic Square Retainer 1 Side Bar 2 12mm x 120mm Hex

More information

Installation Guide Philips MP40/50/60/70 Installation Kit for Penlon Anesthesia Machine

Installation Guide Philips MP40/50/60/70 Installation Kit for Penlon Anesthesia Machine Installation Guide Philips MP40/50/60/70 Installation Kit for Penlon Anesthesia Machine The purpose of this guide is to describe installation of MP40/50/60/70 mounting equipment on the anesthesia machine.

More information

INSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only)

INSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only) INSTALLATION MANUAL FRONT Level of Difficulty Moderate Product Photo (center section only) All hardware listed below will be provided with the bumpers center section. Additional hardware will be supplied

More information

TYGER ARMORTM. Parts List BEFORE INSTALLATION WARNING. Customer Support TG-AM2C /8. x1 Driver/Left Side Armor

TYGER ARMORTM. Parts List BEFORE INSTALLATION WARNING. Customer Support TG-AM2C /8. x1 Driver/Left Side Armor TYGER ARMORTM TG-AM2C20028 Customer Support Parts List x1 Driver/Left Side Armor BEFORE INSTALLATION READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS

More information