Technical Procedure. HIITMill (X) Push/Pull Brake Cable Install

Size: px
Start display at page:

Download "Technical Procedure. HIITMill (X) Push/Pull Brake Cable Install"

Transcription

1 HIITMill (X) Push/Pull Brake Cable Install Applies to: HIITMill and HIITMill X Required Tools: 2.5mm Allen Key 3mm Allen Key 4mm Allen Key 5mm Allen Key 6mm Allen Key 10mm Wrench 10mm Socket Ratchet Needle Nose Pliers 1. Remove the three (3) socket head cap screws securing the brake covers to the unit using a 4mm allen key Latest Rev. 2. Loosen the screw securing the brake cable to the brake, then use a 10mm wrench to remove the M6 nut securing the brake cable to the cable bracket. 3. Pull the entire cable from the back of the brake cable bracket. Page 1

2 4. Remove the brake spring with a pair of needle nose pliers and discard. 5. Use a 4mm allen key to remove the two (2) M8 x 20mm screws from the user left side handrail. 6. Use a 2.5mm allen key to remove the M4 x 8mm screw located in front of the M8 screws removed in Step Repeat Steps for the user right side handrail. 8. Once all the screws securing the handlebar to the frame have been removed, remove the handlebar. Page 2

3 9. Use a 3mm allen key to remove the two (2) M5 x 16mm screws securing resistance lever covers to the user left handrail. 10. Carefully pull up on the resistance lever to remove both the resistance lever assembly and the brake cable. NOTE: The brake cable may need to be fed up through the frame while the level assembly is pulled from the top. 11. Use a 5mm allen key to remove the two (2) M8 x 25mm screws securing the flywheel guard to the frame. 12. Remove the three (3) M10 x 25mm screws securing the user left side handrail to the frame. 13. Carefully separate the user left side handrail from the unit and lay the handrail on the deck. WARNING: Please be aware of any additional cables running from the console to the brake. Ensure these are not damaged or stretched during the removal of the handrail. Page 3

4 14. Feed one end of the new push/pull brake cable up through the bottom of the frame where indicated. NOTE: Some early production units may have a circular opening rather than rectanguar as shown right. 15. Pull the push/pull brake cable up through and out of the hole in the frame. TECH TIP: Use the supplied hook tool to grab the push/pull brake cable and pull it up through the hole while feeing the brake cable from the bottom. 16. Feed the new brake cable up through the user left side handrail ensuring that the cable routes BEHIND the weight horn and swing arm as shown. 17. Reinstall the user left side handrail using the screws removed in Steps Page 4

5 18. After the new cable is routed out of the top of the handrail, attach the cable end fitting to the cable, thread the fitting about 3/4 down the cable. thread one of the cable fitting ends onto the top of the cable. 19. Set the bottom 7/16 nut on the cable to about 1/2 way up the threaded portion of the cable sleeve then slide the resistance lever assembly onto the cable, securing with the 2nd 7/16 nut and 7/16 toothed lock washer. NOTE: The amount of cable that is threaded into the fitting may need to be adjusted in order to attach the new resistance lever assembly. See Step Secure the cable fitting end to the resistance lever using the supplied clevis and cotter pin. 21. Push the resistance lever assembly with attached cable back into the user left handrail, be sure to pull any slack cable out of the bottom of the unit. 22. Using a 6mm allen key, remove and discard the two (2) M8 x 35mm screws from the user left side belt roller guide then install the new cable bracket over the top of the belt roller guide using the provided M8 x 40mm screws. Page 5

6 23. Ensure that the bottom nut located on the cable is threaded all the way down then secure the bottom end of the new brake cable into the new cable bracket. 24. Use a 5mm allen key and a 10mm wrench to remove and replace the brake screw with the screw supplied. 25. Set the resistance to Level 6 then thread a cable fitting end onto the bottom of the cable and connect it to the left side of the brake via the screw installed in Step 24. Ensure that the brake is pushed up against the flywheel while attaching the fitting to the brake screw. 26. Using a 10mm wrench and a 5mm allen key, tighten the M6 nut onto the screw replaced in Step Install the supplied e-clip onto the new brake screw. 28. Remove ONE of the screws securing the brake assembly to the brake using a 6mm allen key, then use a 10mm socket to install one of the supplied hex head screws. DO NOT REMOVE ALL THREE SCREWS AT THE SAME TIME. 29. Repeat Step 28 for the remaining two screws. All three screws should be replaced. Page 6

7 30. Install the new resistance lever covers using a 3mm allen key. Ensure that the STOP icon is facing the rear of the machine. 31. Test the tension on the new cable by pulling the lever all the way back to the STOP position, the belt should not be moving while standing on the unit while the lever is in this postion. If the belt does move, refer to Step 25 as some adjustment may be needed. 32. Install the new outer brake cover using a 4mm allen key and the three (3) screws removed in Step 1. Page 7

STRAIGHT HANDLEBAR KIT

STRAIGHT HANDLEBAR KIT STRAIGHT HANDLEBAR KIT P/N 2881973 APPLICATION All straight bar applications, excluding 550 Indy and Voyageur models BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are

More information

HANDLEBAR KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS TOOLS REQUIRED. Instr Rev Page 1 of 6

HANDLEBAR KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS TOOLS REQUIRED. Instr Rev Page 1 of 6 HANDLEBAR KIT P/N 2881993 APPLICATION All straight bar applications, excluding 550 Indy and Voyageur models BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted

More information

Assembly Instructions: AM-10 Hand & Foot Cycle Early Intervention Part #: 50-HFC-0105

Assembly Instructions: AM-10 Hand & Foot Cycle Early Intervention Part #: 50-HFC-0105 Assembly Instructions: AM-10 Hand & Foot Cycle Early Intervention Part #: 50-HFC-0105 Refer to the following instructions on how to assemble your tryke. Study the instructions carefully before beginning

More information

OPERATOR'S MANUAL 46" SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

OPERATOR'S MANUAL 46 SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY OPERATOR'S MANUAL 46" SNOW BLADE Model Numbers 190-833-OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. FORM NO.

More information

For additional assistance call

For additional assistance call The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or

More information

AX1001. Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS

AX1001. Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS AX1001 Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS EXPLODED DIAGRAM 83 84 84 85/86 87 87 88 89 90 91 62 64 64 64 64 64 64 65 65 65 65 66 66 65 66 66 65 63 63 66 67 68 55 66 66 70

More information

Medium HoneyBadger Chase Rack Installation Instructions

Medium HoneyBadger Chase Rack Installation Instructions PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading

More information

Strata. urniture. Adriana Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at

Strata. urniture. Adriana Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at 1A Watch our assembly videos at www.strataf.com/videos Parts in the Arm Box: Arm - Outside View Arm - Inside View 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached Back Panel

More information

The Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )

The Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 ) P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Do not attempt to install this product on any vehicle other than the one it is designed for and listed above! Parts List 10 3/8 X 1 1/4 Hex Bolt 10 3/8 Lock Washer 4 3/8 Hex Nut 4 3/8 Flat Washer 2 3169)

More information

BY ALIEN TECHNOLOGIES CORP

BY ALIEN TECHNOLOGIES CORP BY ALIEN TECHNOLOGIES CORP Assembly Instructions TopLift Pros YOU MAY ALSO REVIEW OUR ASSEMBLY VIDEO, PLAY AND PAUSE AT YOUR CONVENIENCE. JUST VISIT US AT WWW.TOPLIFTPROS.COM AND GO TO Customer Support

More information

Installation instructions for FC9 & FC18 Forward Controls for Yamaha V-Max

Installation instructions for FC9 & FC18 Forward Controls for Yamaha V-Max Installation instructions for FC9 & FC18 Forward Controls for 1985-2007 Yamaha V-Max It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from

More information

F l a t S c r e e n A R M S I n s t a l l a t i o n

F l a t S c r e e n A R M S I n s t a l l a t i o n ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)

More information

Installation instructions for FC17 Forward Controls for Triumph Rocket III Roadster

Installation instructions for FC17 Forward Controls for Triumph Rocket III Roadster Installation instructions for FC17 Forward Controls for Triumph Rocket III Roadster It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS FOR 07-13 CHEVY SILVERADO 1500 PART#RU-CHSI07-B PARTS LIST: 1 Main Body 28 12mm x 37mm OD x 3mm Large Flat Washers 1 Driver/Left Brush Guard 8 12-1.75mm x 40mm

More information

It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating loose.

It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating loose. Installation instructions for FC12 Forward Controls for Kawasaki Vulcan 750 It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating

More information

Code Product Qty 1 Top Vertex 3 2 Hot End Housing 1 3 Bottom Vertex 3 4 Print Platform Lock 3 5 End Stop Holder 3 6 Filament Feeder Motor Bracket 1 7

Code Product Qty 1 Top Vertex 3 2 Hot End Housing 1 3 Bottom Vertex 3 4 Print Platform Lock 3 5 End Stop Holder 3 6 Filament Feeder Motor Bracket 1 7 List of Parts Code Product Qty 1 680mm Extrusion 3 2 Power Supply 1 3 240mm Extrusion 9 4 42mm Nema 17 Stepper Motor 3 5 Slider-Hotend Connecting Rod 6 6 48mm Nema 17 Stepper Motor 1 7 Linear Rail with

More information

ASSEMBLY AND ADJUSTMENT

ASSEMBLY AND ADJUSTMENT EPPA MONITOR ARM EPPA Rev A 10/17 Model EPPA-XXX ASSEMBLY AND ADJUSTMENT EPPA MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check

More information

MITCHELL WREATH RINGS NO-HAMMER ASSEMBLY INSTRUCTIONS

MITCHELL WREATH RINGS NO-HAMMER ASSEMBLY INSTRUCTIONS MITCHELL WREATH RINGS NO-HAMMER ASSEMBLY INSTRUCTIONS METAL STAND WITH WOOD STAND WITH PAGE 2 OF 10 MASTER PARTS LIST HEAD ASSEMBLY LINKAGE ASSEMBLY HOOK LEVER ASSEMBLY FOOT PEDAL ASSEMBLY ALL FASTENERS

More information

Heavy Duty Ceiling Tilt Mount Installation Manual

Heavy Duty Ceiling Tilt Mount Installation Manual HD-CTM-5580 Heavy Duty Ceiling Tilt Mount Installation Manual *This Installation requires a minimum of two people. For your safety: Read the complete instruction manual before starting an installation

More information

MOTORIZED STANDARD SHADE WITH CABLES Installation Instructions

MOTORIZED STANDARD SHADE WITH CABLES Installation Instructions Tools Needed Drill Measuring Tape Pencil 2 Level Plumb Line ¼ Masonry Drill Bit Hammer Linesmans Pliers Cable Cutters Phillips & Flat-Head Screw Driver 11/32 Socket or Open End Wrench 5/32 Allen Wrench

More information

Arc Trainer Main Frame Assembly

Arc Trainer Main Frame Assembly Arc Trainer Main Frame Assembly Kit No. 610AK019-4 Kit No. 630AK019-4 NOTE: This instruction sheet describes how to replace the main frame assembly in the Arc Trainer 610A. Tools Required 3/16 Allen wrench

More information

INSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058

INSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058 INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks

More information

2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions

2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions 2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2.

More information

mila-wall (Series100) General Operating Instructions page 1 of 15

mila-wall (Series100) General Operating Instructions page 1 of 15 mila-wall (Series100) General Operating Instructions page 1 of 15 Step #1: Before setting up walls, lower adjustable leveling feet on each panel approximately 1". This will allow access to the threaded

More information

STEP 1 : DESTROYER FRONT BUMPER INSTALL GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... *shorty bumper to show hardware* Tools Required:

STEP 1 : DESTROYER FRONT BUMPER INSTALL GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... *shorty bumper to show hardware* Tools Required: DESTROYER FRONT BUMPER INSTALL JL STEP 1 : GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... Tools Required: - Utility knife - 11/16 Deep socket - Ratchet - 11/16 Crescent wrench - Ratchet Extension - 1/4 socket

More information

Repair Instructions. Replacing a La Z Time Mechanism Side Subassembly. Remove the Back(s): Remove the Mechanism Assembly: CAUTION.

Repair Instructions. Replacing a La Z Time Mechanism Side Subassembly. Remove the Back(s): Remove the Mechanism Assembly: CAUTION. Replacing a La Z Time Mechanism Side Subassembly Tools Required: Slotted Screwdriver Power Driver 8" Driver Extension Ruler Note: Extension springs are not typically used on non-chaise standard width styles,

More information

MAG-CONV Basic, 48, 48R & Midline Front Mount

MAG-CONV Basic, 48, 48R & Midline Front Mount Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total

More information

TYGER GUARD. Parts List BEFORE INSTALLATION WARNING TG-GD6D /7. Tyger Guard. Tube Brackets (Bull Bar) passenger or driver side

TYGER GUARD. Parts List BEFORE INSTALLATION WARNING TG-GD6D /7. Tyger Guard. Tube Brackets (Bull Bar) passenger or driver side TYGER GUARD TM BEFORE INSTALLATION TG-GD6D60068 READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED. CUTTING IS

More information

TITAN2-EDGE Public Access Computer Station Dual Track

TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the

More information

Bunk Pod Front Entry Assembly Instructions

Bunk Pod Front Entry Assembly Instructions Bunk Pod Front Entry Assembly Instructions www.podtime.co.uk enquiries@podtime.co.uk Working House Ltd How to assemble your pod This step by step guide will show how to assemble your pod(s) on site. It

More information

ABM International, Inc.

ABM International, Inc. ABM International, Inc. Lightning Stitch required 1 1.0: Parts List head and motor assembly (Qty. 1) Reel stand (Qty. 1) Needle bar frame clamp (Qty. 1) Motor drive (Qty. 1) 2 Cable harness with bracket

More information

Tin Lizzie 18 Assembly Instructions

Tin Lizzie 18 Assembly Instructions Tin Lizzie 18 Assembly Instructions Revision: 07/29/16 Table of Contents Aides 3 Before You Begin 5 Aides 5 Tools 6 Perfect Stitch Parts 2 12 Modify the Machine 12 Prepare Drill Templates 12 Front Display

More information

Installation instructions for FC14S Forward Controls for Shadow ACE and Aero 1100

Installation instructions for FC14S Forward Controls for Shadow ACE and Aero 1100 Installation instructions for FC14S Forward Controls for Shadow ACE and Aero 1100 It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating

More information

Removing the Z-Axis lead screw

Removing the Z-Axis lead screw Page 1 of 8 TITLE: Sabre Z-Axis Lead Screw Replacement Procedure Gerber FastFact #: 5048 Supplied by: Gerber Hardware Support Last Modified: June 14, 2007 Summary: Tools used: The following procedure explains

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET

More information

TorqueMaster Replacement Spring

TorqueMaster Replacement Spring TorqueMaster Replacement Spring Installation Instructions NOTE: Use these installation instructions in conjunction with the TorqueMaster Repair / Replacement Spring Program literature. Copyright 999 Wayne-Dalton

More information

INSTALLATION GUIDE. Model:B60 RECESSED IN WALL MOUNT

INSTALLATION GUIDE. Model:B60 RECESSED IN WALL MOUNT INSTALLATION GUIDE Model:B60 RECESSED IN WALL MOUNT Features: Installs between 16 (406mm) wood stud centers Mounting Pattern Compliance: VESA 100*100mm up to 600 x 400mm Level 5 degree horizontal adjustment

More information

Modern Gatherings 60" TV Console Assembly Instructions

Modern Gatherings 60 TV Console Assembly Instructions Parts List Page 1 of 6 No. Description Sketch Quantity A Console 1 B Door 1 Thank you for purchasing this quality product. Be sure to check all packing material carefully for small parts that may have

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Sheet 1 of 5 General: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #

INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD

More information

SECTION 7 - SUSPENSION

SECTION 7 - SUSPENSION For Arctic Cat Discount Parts Call 606-678-9623 or 606-561-4983 SECTION 7 - SUSPENSION TABLE OF CONTENTS Section Front and Rear Suspension Assembly Schematics... 7-2 Shock Absorbers... 7-4 Swing Arms (ACT

More information

Build the. Steam Locomotive. Pack 05

Build the. Steam Locomotive. Pack 05 Build the Steam Locomotive Pack 05 Build the Steam Locomotive Contents Step by step Stage 29: The leading truck 3 Stage 30: The leading truck 4 Stage 31: The headlamp Stage 32: The smokebox door lock Stage

More information

UR20/UR28 Ouro Site/Area Luminaire Installation Instructions

UR20/UR28 Ouro Site/Area Luminaire Installation Instructions 17760 Rowland Street City of Industry, CA 91748 626/968-5666 FAX 626/369-2695 UR20/UR28 Ouro Site/Area Luminaire Installation Instructions! WARNING: Fixtures must be grounded in accordance with local codes

More information

Assembly Instructions

Assembly Instructions 1 27694 Trend Podium Assembly Instructions #27694 Trend Podium Part Drawing Description Qty Part Drawing Description Qty P-1 Base 1 EA Hardware List Screw M6x12mm 30 EA P-2 Right Side Panel 1 EA A2 Phil

More information

RTI TECHNOLOGIES, INC.

RTI TECHNOLOGIES, INC. RTI TECHNOLOGIES, INC. BRC500 & BRC550 Arbor/Spindle Mechanism Adjustment & Service Technical Instructions The arbor/spindle mechanism of the BRC500/550 is designed to be robust for long life. Occasionally

More information

WARNING: THERE IS ALWAYS A DANGER OF INJURY WHEN

WARNING: THERE IS ALWAYS A DANGER OF INJURY WHEN Assembly Instructions: AM 10 Hand & Foot Cycle Early Intervention Part #: 50 HFC 0105 Refer to the following instructions on how to assemble your tryke. Study the instructions carefully before beginning

More information

Front axle components, overview

Front axle components, overview j a t Front axle components, overview 40-1 General Information Load bearing components and parts of the suspension must not be welded or straightened. Vehicles without drive axle must not be moved, or

More information

Continuum Frame Assembly Instructions

Continuum Frame Assembly Instructions Continuum Frame Assembly Instructions Copyright January 1, 2017 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.2 Table of Contents Continuum Frame Table of Contents... i Warranty...ii

More information

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS 12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions

More information

Jenny Legs Assembly Instructions

Jenny Legs Assembly Instructions Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:

More information

The Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.

The Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2. The Phoenix Professional Quilting Frame Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.1 1 The Phoenix Professional Quilting Frame Parts List Box 1...3 Box

More information

REPLACEMENT TARP for SRT-2 SPOOL ROLL TARP

REPLACEMENT TARP for SRT-2 SPOOL ROLL TARP REPLACEMENT TARP for SRT-2 SPOOL ROLL TARP NOTICE TO INSTALLER: Even if familiar with product, read instructions prior to installation as improvements may be made without notice. Always handle components

More information

User Instructions Multiline Otter Scoreboard Caddy Assembly

User Instructions Multiline Otter Scoreboard Caddy Assembly List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)

More information

OPERATIONAL MANUAL V1.0. Removing/Replacing Blades

OPERATIONAL MANUAL V1.0. Removing/Replacing Blades OPERATIONAL MANUAL V1.0 BLUEROCK WS-212 Wire Stripper Removing/Replacing Blades CAUTION!! IMPORTANT!! DANGER!! WARNING!! DISCONNECT MACHINE FROM POWER BEFORE PROCEEDING!! Estimated Completion Time: 90

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2

INSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2 INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks

More information

SECTION 9: PARTS. Table Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION

SECTION 9: PARTS. Table Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION SECTION 9: PARTS Table Breakdown 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 23 25 17 26 27 8 1 P0675001 CAP SCREW M8-1.25 X 30 15 P0675015 SUPPORT BLOCK 2 P0675002 TABLE SUPPORT BLOCK

More information

WEIGHT ADJUSTABLE ESPREE. Model 2ESP-WA-C48- Model 2ESP-WA-C60- 2ESP-WA Rev B 8/17 ASSEMBLY AND OPERATION

WEIGHT ADJUSTABLE ESPREE. Model 2ESP-WA-C48- Model 2ESP-WA-C60- 2ESP-WA Rev B 8/17 ASSEMBLY AND OPERATION WEIGHT ADJUSTABLE ESPREE PNEUMATIC TABLE BASE 2ESP-WA Rev B 8/17 Model 2ESP-WA-C48- Model 2ESP-WA-C60- = SLV, BLK or WHT ASSEMBLY AND OPERATION PARTS AND TOOLS PLEASE REVIEW these instructions before beginning

More information

STELLA AUTO SIDECAR INSTALL INSTRUCTIONS

STELLA AUTO SIDECAR INSTALL INSTRUCTIONS STELLA AUTO SIDECAR INSTALL INSTRUCTIONS Open crate and inspect sidecar Remove cardboard box from inside the sidecar Remove all hardware holding the sidecar to the crate Remove sidecar from crate Remove

More information

Installation Instructions for FC2 & FC15 Forward Controls for the Super Magna

Installation Instructions for FC2 & FC15 Forward Controls for the Super Magna Installation Instructions for FC2 & FC15 Forward Controls for the Super Magna It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating

More information

RBP-1215B-RX DODGE RAM QUAD CAB RX3

RBP-1215B-RX DODGE RAM QUAD CAB RX3 RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side

More information

INSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1

INSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1 INSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1 IMPORTANT! : The MSP-S11 Mount is designed for use with Sharp 45" LCD displays that have a 200mm x 200mm mounting pattern. IMPORTANT! : The mount

More information

Fresenius Medical Care North America Service Bulletin

Fresenius Medical Care North America Service Bulletin Fresenius Medical Care North America Service Bulletin Equipment: Bulletin: Subject: 2008K@Home Hemodialysis Machines 15-HOM-001 Rev A Optional Shunt Box Ferrite Core Installation (Update) 1.0 PURPOSE To

More information

PERSONAL RECORD KEEPING

PERSONAL RECORD KEEPING 2 P R O 3 7 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for you to obtain

More information

owners Model No CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts

owners Model No CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts owners manual Model No. 45-03022 SLEEVE HITCH CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts the fastest way to purchase parts www.speedepart.com

More information

FACTORY CAT TOMCAT CORPORATION

FACTORY CAT TOMCAT CORPORATION FACTORY CAT RPS TOMCAT CORPORATION Artificial Turf and Carpet Sweeping Install Kit #349-641 & #349-642 1. Detach batteries so that there is no power running through the machine before starting. 2. Start

More information

INSTALLATION INSTRUCTIONS ATV Winch Mounting Kit Part Number: Applications: Honda Rancher. Before You Begin.

INSTALLATION INSTRUCTIONS ATV Winch Mounting Kit Part Number: Applications: Honda Rancher. Before You Begin. INSTALLATION INSTRUCTIONS ATV Winch Mounting Kit Part Number: 68852 Applications: 2000+ Honda Rancher As you read these instructions, you will see NOTES, CAUTIONS, and WARNINGS. Each message has a specific

More information

Speaker Mount Center Channel Speaker Adapter (PAC-301)

Speaker Mount Center Channel Speaker Adapter (PAC-301) I N S T R U C T I O N M A N U A L Speaker Mount Center Channel Speaker Adapter () The Speaker Mount Center Channel Speaker Adapter () uses the same interface as the Side Speaker Adapter and can be used

More information

Cam Handle Service Guide

Cam Handle Service Guide Cam Handle Service Guide Page 2. Introduction Page 3. Troubleshooting guide Page 4-5. Adjusting the clamp force Page 6-7. Disassembling, greasing and replacing components Page 8-9. Replacing the post bearings

More information

MS25 OPERATION MANUAL

MS25 OPERATION MANUAL SAFETY INSTRUCTIONS SPECIFICATIONS OPERATING INSTRUCTIONS MAINTENANCE ADJUSTMENTS REPLACEMENT OF PARTS MS25 DIAGRAM MS25 PARTS LIST MS25 OPERATION MANUAL SAFETY INSTRUCTIONS Please read these instructions

More information

Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide

Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Tools Required: two adjustable wrenches, pliers, ¾ socket wrench recommended Note: please do assembly near your vehicle as you Can

More information

EZ BALANCER II. Please note: The hardware and accessories listed may not be the same as shown. We are always improving the product.

EZ BALANCER II. Please note: The hardware and accessories listed may not be the same as shown. We are always improving the product. Parts List EZ BALANCER II 2ea. Aluminum Angle Base Frame Members. 2ea. 1/2"x1" Aluminum Angle Cross Frame Members. 2ea. Aluminum Uprights. 2ea. Aluminum Cradles. 4ea. Rubber Cradle Guards. 4ea. Rubber

More information

Ford Raptor Venom Front Bumper Installation Instructions

Ford Raptor Venom Front Bumper Installation Instructions PREPARATION 2010 2014 Ford Raptor Venom Front Bumper Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend

More information

200A FLB VERTICAL 22113V LIFT W/CHAIN DRIVE WINCH

200A FLB VERTICAL 22113V LIFT W/CHAIN DRIVE WINCH PG. 1 OF 11 PORTA-DOCK, INC. 200A FLB VERTICAL 22113V LIFT W/CHAIN DRIVE WINCH STEP 1. Separate and group like parts and fasteners together. Locate the winch side member with the longer upright tube and

More information

3,500/4,500lb. Vertical Cable Feighner Lift

3,500/4,500lb. Vertical Cable Feighner Lift 3,500/4,500lb. Vertical Cable Feighner Lift CAUTION - PUT SAFETY FIRST 1. Before attempting to install or operate this lift, study and fully understand the proper operating procedures and safety precautions

More information

Removing outter components

Removing outter components Y Axis Motor Replacement Replacing the Y axis motor is a process that requires the individual to be somewhat mechanically inclined and can follow detailed instructions. If any of the following steps are

More information

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C) Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the

More information

Replacing the Reciprocator on an SWF Multi-head.

Replacing the Reciprocator on an SWF Multi-head. Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the

More information

Lead Screw Cover Installation

Lead Screw Cover Installation The premier source of tooling, parts, and accessories for bench top machinists. Lead Screw Cover Installation These instructions cover two products: 5201 Telescoping Lead Screw Cover, 7x10, 7x12 5202 Telescoping

More information

Metroboard Pulley Replacement Procedure

Metroboard Pulley Replacement Procedure Metroboard Pulley Replacement Procedure 1) Remove the two transmission cover screws (1/8 allen driver). Then remove the transmission cover. Note there is a split lock washer and flat washer as well, so

More information

STEINBERGER TRANSTREM (TYPE 2) TECHNICAL DOCUMENT

STEINBERGER TRANSTREM (TYPE 2) TECHNICAL DOCUMENT STEINBERGER TRANSTREM (TYPE 2) TECHNICAL DOCUMENT These instructions apply to newer style TransTrems only (non-threaded ball type or modified threaded ball type). For purposes of discussion, these TransTrems

More information

Riverside. Windhaven Queen Storage Bed Assembly Instructions

Riverside. Windhaven Queen Storage Bed Assembly Instructions Queen Storage Bed Page 1 of 7 2 pcs. 4 pcs. 4 pcs. 4 pcs. 2 pcs. 5/0 Queen Storage Bed 50773 -- 5/0 Storage Footboard w/platform Note: The 50773 Storage Footboard can be used with the 50770 Panel Headboard

More information

Riverside. Harbor Hill Queen Storage Bed Assembly Instructions

Riverside. Harbor Hill Queen Storage Bed Assembly Instructions Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 2 pcs. 3 pcs. 3 pcs. 4 pcs. 4 pcs. 4 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 2 pcs. 8 pcs. 1 pc. 25770 -- 4/6-5/0 Panel Headboard (NOTE: the 25775 Leather

More information

INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000

INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with

More information

This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently.

This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. Don t be put off by the size of the instruction manual as the large diagrams

More information

Strata. urniture. Mission Rim Instructions. Parts in the Arm Box: Parts in the Body Box:

Strata. urniture. Mission Rim Instructions. Parts in the Arm Box: Parts in the Body Box: 1A Watch our assembly videos at www.strataf.com/videos.html Parts in the Arm Box: Arm - Outside View Arm - Inside View Corbels x 4 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached

More information

TABLE OF CONTENTS REQUIRED TOOLS

TABLE OF CONTENTS REQUIRED TOOLS TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS

More information

**MOUNTING YOUR MONITOR

**MOUNTING YOUR MONITOR FPP72V200 72 FREE STANDING DISPLAY CART Assembly Instructions Hardware List Ref. Qty. Part No. Description AA 4 030-1128 1/4-20 UNC, 1 3/4 Socket Hd Screws BB 1 030-1129 5/8-11 UNC 1 3/4 Socket Hd Screw

More information

Tools Required: Materials Identification and Segregation: Disassembly Steps: Aeron Disassembly for Recycling

Tools Required: Materials Identification and Segregation: Disassembly Steps: Aeron Disassembly for Recycling Y Aeron Disassembly for Recycling Tools Required: Power Driver 2 lbs Hammer Torx Bit Safety Glasses Rubber Mallet Materials Identification and Segregation: Where possible, plastic components are marked

More information

Riverside. Oakmont Queen Storage Bed Assembly Instructions

Riverside. Oakmont Queen Storage Bed Assembly Instructions Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 1 pc. 1 pc. 20270 --5/0 Sleigh Headboard 20274 --5/0-6/6 Bed Rails 20273 -- 5/0 Storage Footboard, Panels, Slats Queen

More information

WOLF PUP LOOM TM & WOLF PUP LT LOOM TM

WOLF PUP LOOM TM & WOLF PUP LT LOOM TM WOLF PUP LOOM TM & WOLF PUP LT LOOM TM Assembly Instructions FL3000 FL3006 FL3009 WOLF PUP WOLF PUP LT Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212

More information

C 0.05" ALLEN WRENCH. Installation Instructions for Cirrus Channel Suspension T1 with 4" Square or Round Canopy. Section One: Adjusting Cable Position

C 0.05 ALLEN WRENCH. Installation Instructions for Cirrus Channel Suspension T1 with 4 Square or Round Canopy. Section One: Adjusting Cable Position Doc # 90-CST-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension

More information

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards. Installation Instructions for Fortress Horizontal Cable Panel System with UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all

More information

Riverside. Harbor Hill King Storage Bed Assembly Instructions

Riverside. Harbor Hill King Storage Bed Assembly Instructions King Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 2 pcs. 6 pcs. 3 pcs. 4 pcs. 4 pcs. 4 pcs. 1 pc. 1 pc. 2 pcs. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 25780 -- 6/0-6/6 Panel Headboard (NOTE: the 25785 Leather Headboard

More information

INSTALLATION INSTRUCTIONS ATV PLOW Mount Kit: PN Application: Sportsman 400, Magnum 425

INSTALLATION INSTRUCTIONS ATV PLOW Mount Kit: PN Application: Sportsman 400, Magnum 425 INSTALLATION INSTRUCTIONS ATV PLOW Mount Kit: PN 37845 Application: 1996-97 Sportsman 400, 1997-98 Magnum 425 Your safety, and the safety of others, is very important. To help you make informed decisions

More information

INSTALLATION INSTRUCTIONS for the JOMY RETRACTABLE LADDER. If there are any questions, please call (800)

INSTALLATION INSTRUCTIONS for the JOMY RETRACTABLE LADDER. If there are any questions, please call (800) INSTALLATION INSTRUCTIONS for the JOMY RETRACTABLE LADDER If there are any questions, please call (800) 255-2591 INSTALLATION INSTRUCTIONS WARNING! Ladder Sections Lock When Closed. Do Not Install or Close

More information

Intercooler Shroud and Belt Cover for WRX

Intercooler Shroud and Belt Cover for WRX Intercooler Shroud and Belt Cover for 2015+ WRX 2016-05-18 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory WELL P/N 08P21-STX-200A Application 2011 MDX Publications No. BII 43668 Issue Date AUG 2010 PARTS LIST Left front fender trim Bracket A-L Left front bumper trim Bracket

More information

TRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS

TRUE TECHNICAL SERVICE MANUAL - ALL MODELS.  DOORS/DRAWERS/LIDS DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Springs 97 TORSION SPRING REPLACEMENT GDM RADIUS FRONT - SWING DOOR INSTALLATION INSTRUCTIONS Tools Required (2) - 1 8" drift Punch (forged) Needle-Nose

More information

CFT STRENGTH TRAINING SYSTEM OWNER'S MANUAL

CFT STRENGTH TRAINING SYSTEM OWNER'S MANUAL CFT STRENGTH TRAINING SYSTEM OWNER'S MANUAL Serial Number Location SERIAL 8 Record your Serial number and purchase date here: S/N PURCH.DATE: DEALER: Scan this QR code with your PortableDevice to link

More information