TEST REPORT Metallic materials - Tensile testing (traction test) at room temperature
|
|
- Rodger Sutton
- 5 years ago
- Views:
Transcription
1 LGAI Technological Center, S.A. Campus UAB s/n Ronda de la Font del Carme, s/n E Bellaterra (Barcelona) T F Bellaterra: June 19, 2015 Report number: 15/ Petitioner reference: PAGOUNI, S.A. 9th km Old nat. road Thessaloniki Veria ECHEDOROS THESSALONIKI, PC (Greece) TEST REPORT Metallic materials - Tensile testing (traction test) at room temperature This document may only be reproduced in full. Only reports with an original signature on their respective certified copies will be legally valid. This document has 7 pages. This is the 1 st page. LGAI Technological Center S.A. Inscrita en el registro Mercantil de Barcelona, Tomo , Folio1, Hoja Nº B Inscripción 1ª C.I.F. : A
2 Report number: 15/ Page number 2 of 7 Table of contents 1.- RECEIVED MATERIAL REQUESTED MATTER TEST METHOD Sampling method Test description Testing equipment TESTING CONDITIONS RESULTS... 5
3 Report number: 15/ Page number 3 of 7 RECEIVED MATERIAL Six (6) samples with the reference that appear in Table 1, as claimed by the petitioner Table 1. Received material references. Ref. Applus Customer identification Sample description MEC 15/0296_1 MEC 15/0296_2 MEC 15/0296_3 MEC 15/0297_1 MEC 15/0297_2 MEC 15/0297_3 DOMOLAM PANELS 0.35mm DOMOLAM PANELS 0.35mm DOMOLAM PANELS 0.35mm DOMOLAM PANELS 0.40mm DOMOLAM PANELS 0.40mm DOMOLAM PANELS 0.40mm Date of material receipt: May 15, REQUESTED MATTER Mechanical characterisation, specifically, tensile testing (traction test) at room temperature on standardised specimens taken from each receipt reference, according to standard UNE-EN ISO : TEST METHOD Sampling method The samples have been selected and delivered by the petitioner. Reference of the test specimen dimensions were determined according to Annex B and D of the standard UNE-EN ISO :2010, which makes reference to the types of test specimens used for thin products: steel sheet, strips and flat products with thickness between 0,1mm and 3 mm, respectively. In figure 1 test sample used and the machining dimensions is shown.
4 Report number: 15/ Page number 4 of 7 Figure 1. Sketch and dimensions of the traction specimen test Test description The traction test was conducted in accordance with the applicable paragraphs of standard UNE-EN ISO :2010. Tests were conducted under displacement rate control, at a speed of 1,4 mm min -1 up to a 2% deformation. From this point to failure test was perform in displacement control at a rate of 4 mm min Testing equipment For conducting the tensile tests on standard samples were used the following equipment: Tests were performed in a universal test machine, MTS, model 810 and serial number , with a capacity of 100 KN and class 0.5, standard ISO :2006, on a calibrated range of 100 KN. Deformation of tests samples was measured continuously during the test, using an MTS extensometer; model F-20 and serial number 1390, measuring 25 mm in initial length, with maximum opening to traction, 12.5mm. The initial section of the sample and the elongation at break were calculated by measuring several times the thickness, width and the distance between the marks, by means of a MITUTOYO digital caliper, model and serial number 31819, with 150 mm of range.
5 Report number: 15/ Page number 5 of TESTING CONDITIONS The test was performed at an ambient temperature of 22 ± 1 C. 4.- RESULTS Performed test days Start: June 16, 2015 End: June 16, 2015 Further to conducting the traction test according to the instructions in the Test Method section, the results of nine specimens as requested by the petitioner are summarized in Tables 2-3 and Graphics 1-2: Table 2. Resume traction test results for specimen MEC 15/0296. Probeta E R p0,2 R m A 15 [GPa] [MPa] [MPa] [%] MEC 15/0296_ MEC 15/0296_ MEC 15/0296_ Promedio Desvest. (%) Table 3. Resume traction test results for specimen MEC 15/0297. Probeta E R p0,2 R m A 16 [GPa] [MPa] [MPa] [%] MEC 15/0297_ MEC 15/0297_ MEC 15/0297_ Promedio Desvest. (%) The tests have been conducted may be deemed valid, since the break occurred in the calibrated length and exceeded the minimum distance to the clamps, in accordance with standard UNE-EN ISO :2010. The expanded uncertainty of measurement has been expressed as the relative standard uncertainty of measurement multiplied by a factor k = 2 which for a normal distribution corresponds to a coverage probability of approximately 95%.
6 Report number: 15/ Page number 6 of 7 Graphic 1. Curve Stress (MPa) vs. Deformation (%) registered at traction test for specimen MEC 15/0296. Graphic 2. Curve Stress (MPa) vs. Deformation (%) registered at traction test for specimen MEC 15/0297.
7 Report number: 15/ Page number 7 of 7 Raúl Navarro Garcia Technical Manager Mechanical Testing Laboratory LGAI Technological Center S.A. Results are exclusively related to the specimens, products or materials received by the Laboratory, which are fully described in the corresponding report item and to the testing conditions described in this test report Service Applus+, Quality guarantees Assurance that this work has been made in accordance with our Quality and Sustainability System, fulfilling the contractual conditions and legal norms. Within our improvement program we would be grateful if you would send us any commentary that you consider opportune, to the person in charge who signs this document, or to the Quality Manager of Applus+, in the following address: satisfaccion.cliente@appluscorp.com
Bellaterra: File number: 15/ Via Bellavista Pallejà. Humitat Stop S.L.
LGAI Technological Center, S.A. Campus de la UAB Apartado de Correos 18 E - 08193 Bellaterra (Barcelona) T +34 93 567 20 00 F +34 93 520 20 01 www.appluslaboratories.com Bellaterra: 2015-05-29 File number:
More informationPreload Measurement and Comparison of Structural Bolts sets installed in Steel Connections with and without Direct Tension Indicators
Bellaterra 12/03/2007 Reference 06/31700676i To Tornilleria Industrial, S.A. (FATOR) Cristina Hernández c/ Catalunya Nº 11 Pol. Industrial Can Oller 08130 Santa Perpètua de Mogoda BARCELONA Preload Measurement
More informationISO 783 INTERNATIONAL STANDARD. Metallic materials Tensile testing at elevated temperature
INTERNATIONAL STANDARD ISO 783 Second edition 1999-08-15 Metallic materials Tensile testing at elevated temperature Matériaux métalliques Essai de traction à température élevée A Reference number ISO 783:1999(E)
More informationProduct Information. makroxtens II
CTA: 44098 44269 PI 220 0119 Applications is a universal, high resolution extensometer for tensile, compression, flexure and cyclic tests on plastics, composites, hard foam materials and metals that have
More informationREPORT ON THE ON-SITE ACOUSTIC MEASUREMENTS CARRIED OUT TO CALCULATE THE ACOUSTIC INSULATION OF THE WEWORK+ CABIN
REPORT ON THE ON-SITE ACOUSTIC MEASUREMENTS CARRIED OUT TO APLING, SLU - Comm. Reg. of Barcelona: Tome 32162. Sheet 0188. General Sect. Entry. 1ª Page 209026 C.I.F. B-60413499 CALCULATE THE ACOUSTIC INSULATION
More informationContents DIN 50125:
14 Contents Foreword... 3 1 Scope... 4 2 Normative references... 4 3 Terms and definitions... 4 4 Types, dimensions, and designation... 4 4.1 General... 4 4.2 Type A test pieces... 6 4.3 Type B test pieces...
More informationTECHNICAL SPECIFICATION FOR. CONTACT WIRE HARD-DRAWN COPPER 161mm2
Engineering Specification Electrical TECHNICAL SPECIFICATION FOR CONTACT WIRE HARD-DRAWN COPPER 161mm2 Version: 2 Issued: May 2018 Owner: Engineering Approved by: Andrew Russack, Head of Engineering Electrical
More informationUniversal Sheet Metal Testing Machines. for Research, Development and In-process Testing
Universal Sheet Metal Testing Machines for Research, Development and In-process Testing Application - Example: Automotive Industry Models - Technical Data - Additional Control Functions and Test Methods
More informationInitial wet-web tensile strength, stretch and tensile energy absorption
Accepted 1977 Ed. updated 2005 Mechanical and chemical pulps Initial wet-web tensile strength, stretch and tensile energy absorption 25 % dry matter content 0 Introduction SCAN-CM 31:77, applicable to
More informationTest Report No.: /k-e Date: PMMA-sheets PLEXIGLAS SOUNDSTOP GS CC for. Impact test according to pren :2002; Annex B
Test Report No.: Date: 2003-05-07 PMMA-sheets PLEXIGLAS SOUNDSTOP GS CC: Impact testing according to pren 1794-2:2002 Client: Para-Chemie GesmbH Hauptstraße 53 A-2440 Gramatneusiedl Test item: PMMA-sheets
More informationMESP TECHNICAL SPECIFICATION FOR CATENARY WIRE HARD-DRAWN COPPER 37/ mm 2
Engineering Specification Electrical Networks TECHNICAL SPECIFICATION FOR CATENARY WIRE HARD-DRAWN COPPER 37/2.5 181mm 2 Version: 3 Issued: February 2017 Owner: Engineering Division Approved By: Andrew
More informationTHIN-WALLED HOLLOW BOLTS
THIN-WALLED HOLLOW BOLTS Experimental and numerical study Teixeira, C. D. S. Department of Mechanical Engineering, Instituto Superior Técnico, Av. Rovisco Pais, 1049-001, Lisbon, Portugal, 2010 Abstract
More informationProposal for new standard. Determination of interface friction between painted parts. Orientation. p. 1 (15) Draft1, Revised
p. 1 (15) Draft1, Revised 2018-03-29 Proposal for new standard Determination of interface friction between painted parts. Orientation This standard specifies the method and conditions to evaluate interface
More informationBolts and Set Screws Are they interchangeable?
1903191HA Bolts and Set Screws Are they interchangeable? Prof. Saman Fernando Centre for Sustainable Infrastructure SUT Introduction: This technical note discusses the definitions, standards and variations
More informationDIGITAL PANEL METER N24 AND N25 METER SERIES
DIGITAL PANEL METER N24 AND N25 METER SERIES USER S MANUAL Contents 1. APPLICATION...5 2. METER SET...5 3. OPERATIONAL SAFETY...6 4. INSTALLATION...7 4.1 Fixing Way...7 4.2 External Connection Diagrams...8
More informationTEST SERIES TO EVALUATE THE STRUCTURAL BEHAVIOUR OF ISOBOARD OVER RAFTER SYSTEM
TEST SERIES TO EVALUATE THE STRUCTURAL BEHAVIOUR OF ISOBOARD OVER RAFTER SYSTEM J A Wium Institute of Structural Engineering 19 November 2007 ISI2007-3 TEST SERIES TO EVALUATE THE STRUCTURAL BEHAVIOUR
More informationInstruction manual. ZCY 2400 Zehntner-Cylindrical mandrel tester
Zehntner GmbH Testing Instruments Gewerbestrasse 4 CH-4450 Sissach Switzerland Tel +41 (0)61 953 05 50 Fax +41 (0)61 953 05 51 zehntner@zehntner.com www.zehntner.com Instruction manual Version 1.0 vom
More informationMESP TECHNICAL SPECIFICATION FOR MURL JUMPER WIRE HARD-DRAWN COPPER 19/ mm 2
Engineering Specification Electrical Networks MESP 130400-07 TECHNICAL SPECIFICATION FOR Version: 1 Issued: February 2017 Owner: Engineering Division Approved By: Andrew Russack Head of Engineering (Electrical)
More informationCTAG:b01ac469edcbee4d9e5f84a83a1962a5 Certificate of Calibration
CTAG:bac69edcbeed9e5f8a8a96a5 Certificate of Calibration Data Type: FOUND-LEFT Certificate No: 859 Instrument Description Manufacturer Model Serial Number Inventory Number CABLE ANALYZER FLUKE NETWORKS
More informationGESTER. Universal Testing Machine (Dual Column) GT-K01. Product Presentation. Application. Test Sample.
Product Presentation Universal Testing Machine (Dual Column) GT-K01 Application This tester is designed for conducting tensile, compression, bending, shearing, bonding strength, peeling, tearing and other
More informationEnglish version. Steel and steel products Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997)
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN ISO 377 July 1997 ICS 77.040.10; 77.140.01 Descriptors: See ISO document English version Steel and steel products Location and preparation of samples
More informationUniversal Sheet Metal Testing Machine Model 142
Bore Expanding ISO 16630 Deep Drawing Cup Test Universal Sheet Metal Testing Machine Model 142 Square Deep Drawing Cup Test Software for Data Evaluation and Processing testing equipment for quality management
More information012: 2015 CEB SPECIFICATION GALVANIZED STEEL WIRE (EXCEPT SHIELDING WIRE FOR TOWER LINE APPLICATION)
012: 2015 CEB SPECIFICATION GALVANIZED STEEL WIRE (EXCEPT SHIELDING WIRE FOR TOWER LINE APPLICATION) CEYLON ELECTRICITY BOARD SRI LANKA Telephone: +94 11 232 8051 Fax: +94 11 232 5387 CONTENTS Page 1.0
More informationFinal Publishable Summary
Final Publishable Summary Task Manager: Dr. Piotr Klimczyk Project Coordinator: Mr. Stefan Siebert Dr. Brockhaus Messtechnik GmbH & Co. KG Gustav-Adolf-Str. 4 D-58507 Lüdenscheid +49 (0)2351 3644-0 +49
More informationADVANCED. Universal Sheet Metal Testing Machine Model 142
ADVANCED Universal Sheet Metal Testing Machine Model 142 ASTM 643-09, ISO 11 531, EN ISO 20482, DIN EN 1669 Applications Qualitest s Universal Sheet Metal Testing Machine with electro-hydraulic drive,
More informationTECHNICAL INFORMATION P10/0513 vitroflex LED EDGELIGHT features
TECHNICAL INFORMATION P10/0513 vitroflex LED EDGELIGHT features Vitroflex LED EDGELIGHT is the special compact acrylic sheet for signage illuminated around the perimeter of the sheet by LEDs. LED EDGELIGHT
More informationSEI Certification Program Manual
Safety Equipment Institute SEI Certification Program Manual Section 29: Industrial Protective Clothing and Equipment Program 0 of 6 SEI Certification Program Manual Section 29: Industrial Protective Clothing
More informationAll the standards referred to the most current issue, including all amendment supplements. as of the date of the bid.
1. Scope This specification defines the methods, the procedures and the requirements to verify the cables manufactured according to I.E.C. Specifications NPS361. 2. Standards All the standards referred
More informationSSAB Laser OPTIMIZED FOR YOU AND LASER CUTTING
SSAB Laser OPTIMIZED FOR YOU AND LASER CUTTING If other steel doesn t behave to perfection, try SSAB Laser. It has guaranteed flatness both before and after cutting. SSAB LASER THE ULTIMATE CHOICE FOR
More informationThe Formability of Perforated Metals, Part II: Stainless Steel and Aluminum
The Formability of Perforated Metals, Part II: Stainless Steel and Aluminum A follow-up study sponsored by The Industrial Perforators Association and conducted by Robert H. Wagoner, Department of Materials
More informationMESP TECHNICAL SPECIFICATION FOR TRANSMISSION WIRE HARD-DRAWN COPPER 19/ mm 2
Engineering Specification Electrical Networks TECHNICAL SPECIFICATION FOR TRANSMISSION WIRE HARD-DRAWN COPPER 19/2.14 70mm 2 Version: 1 Issued: January 2015 Owner: Engineering Division Approved By: Pat
More informationA NEW MOTION COMPENSATION TECHNIQUE FOR INFRARED STRESS MEASUREMENT USING DIGITAL IMAGE CORRELATION
A NEW MOTION COMPENSATION TECHNIQUE FOR INFRARED STRESS MEASUREMENT USING DIGITAL IMAGE CORRELATION T. Sakagami, N. Yamaguchi, S. Kubo Department of Mechanical Engineering, Graduate School of Engineering,
More informationtesto 735, highly accurate alarm and logger thermometer with measurement site management
14 testo 735, highly accurate alarm and logger thermometer with measurement site management Wireless measurement with radio probes for air, iersion and penetration measurement Evaluate and document readings
More informationMetallic materials Sheet and strip Method for springback evaluation in stretch bending
INTERNATIONAL STANDARD ISO 24213 Second edition 2017-07 Metallic materials Sheet and strip Method for springback evaluation in stretch bending Matériaux métalliques Tôles et bandes Méthode d évaluation
More informationSPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS
UDC 621.882.211 [669.14.018.291] IS : 3757-1985 (Reaffirmed 2003) Edition 3.2 (1989-07) Indian Standard SPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS ( Second Revision ) (Incorporating Amendment Nos.
More informationCOMITÉ EUROPÉEN DES ASSURANCES
COMITÉ EUROPÉEN DES ASSURANCES SECRETARIAT GENERAL 3bis, rue de la Chaussée d'antin F 75009 Paris Tél. : +33 1 44 83 11 73 Fax : +33 1 44 83 11 85 Web : cea.assur.org DELEGATION A BRUXELLES Square de Meeûs,
More informationTESTS REPORT n. 220.I EN.02
Reference: 1705003-01 Order sheet: 21702678 TESTS REPORT n. 220.I.1705.311.EN.02 ON THE REQUEST OF COMPANY: INDÚSTRIAS QUIMICAS IRIS, S.A. PERSON IN CHARGE: FRANCISCO MONTERO ADDRESS: PG. PICASSENT, BUZÓN
More informationInstruction Manual for installing
Instruction Manual for installing Preloaded (HSFG) Bolting with TurnaSure DIRECT TENSION INDICATORS CE Marked EN 14399-9 TurnaSure LLC TABLE OF CONTENTS Introduction... 1 Theory of Preloaded Bolting Assemblies...
More information6 Audio Broadcast PER 528
6 Technical Data Audio Broadcast Tape Audio Broadcast PER 528 PER 528 meets the quality standards as required by major European radio broadcasters. Offering outstanding electroacoustic and mechanical characteristics;
More informationLED Driver Constant voltage
Driver LCU 35W 12/24V IP20 EXC EXCITE indoor IP20 series Product description LED Driver Universal input voltage range Constant output voltage Push terminals for simple wiring Nominal life-time up to 50,000
More informationInstruction Manual for installing
Instruction Manual for installing Preloaded (HSFG) Bolting with TurnaSure DIRECT TENSION INDICATORS TurnaSure LLC TABLE OF CONTENTS Introduction... 1 Theory of Preloaded Bolting Assemblies... 2 Tightening
More informationComparative Evaluation of Resistance Made Simple Shear Connection with Bolts and With Welding
International Journal of Engineering Inventions e-issn: 78-7461, p-issn: 319-6491 Volume 3, Issue 7 (February 014) PP: 1-5 Comparative Evaluation of Resistance Made Simple Shear Connection with Bolts and
More informationElcometer Conical Mandrel Bend Tester
English Elcometer 1510 Conical Mandrel Bend Tester Operating Instructions English is a registered trademark of Elcometer Instruments Ltd. All other trademarks acknowledged. Copyright Elcometer Instruments
More informationMaterials. Density, Hooke's law, Young modulus. 174 minutes. 174 marks. Page 1 of 29
Materials Density, Hooke's law, Young modulus 174 minutes 174 marks Page 1 of 29 Q1. A uniform wooden beam of mass 35.0 kg and length 5.52 m is supported by two identical vertical steel cables A and B
More informationEuropean Technical Assessment ETA 15/0029 of 12/06/2017
RISE Research Institutes of Sweden AB RISE Certifiering Box 553 SE-371 23 Karlskrona Sweden Member of www.eota.eu Tel: +46 10 516 63 00 Web: www.ri.se Mail: certifiering@ri.se European of 12/06/2017 General
More informationSheet Metal Testing Machine Model 134
ERICHSEN Cupping Test Deep Drawing Cup Test Sheet Metal Testing Machine Model 134 Square Deep Drawing Cup Test Bore Expanding Test testing equipment for quality management Technical Description Data logger
More informationN24, N25 DIGITAL PANEL METER
DIGITAL PANEL METER www.sifamtinsley.co.uk USER S MANUAL Multifunction Meters Transducers & Isolators Temperature Controllers Converters & Recorders Digital Panel Meters DIGITAL PANEL METER Current Transformers
More informationTest Report COMPRESSION TEST ON COLD-FORM STEEL MEMBERS
Test Report COMPRESSION TEST ON COLD-FORM STEEL MEMBERS by Associate Professor Dr.Choong Kok Keong (Principal Investigator) Dr. Fatimah De nan (Co-Investigator) School of Civil Engineering Engineering
More informationGURANTEED TECHNICAL PARTICULARS OF BACK CLAMP FOR LT CROSS ARM
Technical Specification of Back Clamp for LT Cross Arm (MS) Back clamp for LT Cross Arm made out of 50 x 6mm MS Flat suitable for 8m X 300 Kg PSC poles. After fabrication the cross arm shall be painted
More informationStrain Measurements with the Digital Image Correlation System Vic-2D
CU-NEES-08-06 NEES at CU Boulder 01000110 01001000 01010100 The George E Brown, Jr. Network for Earthquake Engineering Simulation Strain Measurements with the Digital Image Correlation System Vic-2D By
More informationChemical composition. Type 2 as per F568: C ( ); P (max 0.048); S (max 0.058); Mn (min 0.74); B (min );
BS EN 14399 HIGH STRENGTH STRUCTURAL BOLTING FOR PRE LOAD Direct comparison as an alternative to ASTM HSFG Bolts ASTM A325M Type 1, ASTM A490M Type 1 or 2 BS EN 14399-3:2005 Grade 8.8 and 10.9 Chemical
More informationLED Driver Constant voltage
Driver LCU 100/96W 12/24V IP20 EXC EXCITE indoor IP20 series Product description LED Driver Universal input voltage range Constant output voltage Push terminals for simple wiring Nominal life-time up to
More informationBBD7267 Version 1 PRIEVIEW COPY ONLY
INDEX SECTION CONTENTS PAGE 1.0 SCOPE 3 2.0 REFERENCES 3 3.0 APPENDICES 3 4.0 METHOD OF TENDERING 3 5.0 MATERIAL 3 6.0 MARKING 3 7.0 SIZE AND LENGTH 4 8.0 DRUMS AND WINDING 4 9.0 MARKING OF DRUMS 4 10.0
More informationSchedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK
CET Structures Ltd. trading as CET Calibration M1 Commerce Park Markham Lane Duckmanton Chesterfield S44 5HS Contact: Mr Chris Locke Tel: +44 (0)1246 828318 Fax: +44 (0)1246 828319 E-Mail: chris.locke@cetcalibration.com
More information5 m-measurement system for traceable measurements of tapes and rules
5 m-measurement system for traceable measurements of tapes and rules Tanfer Yandayan*, Bulent Ozgur Tubitak Ulusal Metroloji Enstitusu (UME) PK54, 4147 Gebze-KOCAELI / TURKEY ABSTRACT Line standards such
More informationFatigue crack propagation in uniaxial loading and bending fatigue in 20 khz testing. Mohamed Sadek PhD Student Karlstad university
Fatigue crack propagation in uniaxial loading and bending fatigue in 20 khz testing Mohamed Sadek PhD Student Karlstad university 2017-02-08 EU - project Influence of cyclic frequency on fatigue strength
More informationSOLARLOK PV BAR Junction Box
SOLARLOK PV BAR Junction Box Table of contents 1. SCOPE... 2 1.1. Content... 2 1.2. Qualification... 3 2. APPLICABLE DOCUMENTS... 3 2.1. TE Connectivity Documents... 3 2.2. Commercial Standard... 3 3.
More informationInternal threaded version: HSC-I carbon steel internal version HSC-IR Stainless steel version (A4) Hilti anchor design software
Anchor version Benefits Internal threaded version: HSC-I carbon steel internal version HSC-IR Stainless steel version (A4) the perfect solution for small edge and space distance suitable for thin concrete
More informationUltrasonic Bolt Load Measurement
Ultrasonic Bolt Load Measurement Echometer ECM-1 The echometer ultrasonically measures the elongation, stress and load in fasteners, quickly and accurately, and displays the result on an easy to read screen.
More informationLED Driver Constant voltage
Driver LCU 60W 12/24V IP20 EXC excite series Product description LED Driver Universal input voltage range Constant output voltage Push terminals for simple wiring Nominal life-time up to 50,000 h (at ta
More informationDOWEL ACTION OF TITANIUM BARS CONNECTING MARBLE FRAGMENTS AT DIFFERENT ANGLES
13 th International Brick and Block Masonry Conference Amsterdam, July 4-7, 2004 DOWEL ACTION OF TITANIUM BARS CONNECTING MARBLE FRAGMENTS AT DIFFERENT ANGLES E.Vintzileou 1, E.-E.Toumbakari 2 Abstract
More informationImproving Edge Quality in Film Applications with Tangent Shear Slitting
Improving Edge Quality in Film Applications with Tangent Shear Slitting Presented by: Sean Craig General Manager, Maxcess-Tidland Date: October 17, 2017 What is Fracture Mechanics? The study of how things
More informationCARES Technical Approval Report TA1-B 5042
CARES Technical Approval Report TA1-B 5042 Issue 4 Dextra ROLLTEC Standard, Positional and Caging Couplers Assessment of the Dextra ROLLTEC Standard, Positional and Caging Coupler Product and Quality System
More informationDowel connections in laminated strand lumber
Dowel connections in laminated strand lumber Cranswick, Chad J. 1, M c Gregor, Stuart I. 2 ABSTRACT Laminated strand lumber (LSL) is a relatively new structural composite lumber. As such, very limited
More informationThe surveillance test is a physical inspection of the product and a comparison with the specifications of the original type tested sample.
SOLAR KEYMARK SPECIFIC SCHEME RULES ANNEX A2. SOLAR KEYMARK SURVEILLANCE TEST Normative annex. Version of 2012-09-09. 1 Introduction This document gives a brief description of the procedure of the so called
More informationThe Bombay Textile Research Association, L. B. S. Marg, Ghatkopar (West), Mumbai, Maharashtra. Discipline Mechanical Testing Issue Date
Last Amended on - Page 1 of 7 I. TEXTILES & RELATED PRODUCTS 1. FIBRES Neps in Cotton Fibres (AFIS-N-Instrument) Physical Properties of Cotton Fibres by High Volume Instrument (HVI) 2.5% Span Length Uniformity
More informationTesting of friction properties of fasteners
2018-02-13 Sida 1 (31) Testing of friction properties of fasteners Contents 1 Introduction 2 2 Scope 2 3 Terms and definitions 3 4 Structure of evaluation of friction properties 5 5 Cleaning of test parts
More informationPHASED OUT. LED Driver Linear / area fixed output. Driver LCI 35W 350mA 900mA TOP lp TOP series
Product description Fixed output built-in LED Driver Constant current LED Driver Output current settable 350 900 ma Max. output power 35 W Nominal life-time up to 100,000 h For luminaires of protection
More informationDevelopment of an Embedded Sensor Holder for Concrete Structures Monitoring
Development of an Embedded Sensor Holder for Concrete Structures Monitoring Sousa, H., Matos, J. C., Figueiras, J. A. LABEST Laboratory for the Concrete Technology and Structural Behaviour Faculty of Engineering,
More informationMicro IRHD Laser revolution
Micro IRHD Laser revolution Micro-IRHD Hardness tester with laser centring device and rotating sample holder for the automatic serial measure of O-rings and small rubber parts The instruments is supplied
More informationS-BT screw-in stainless steel and carbon steel threaded studs
S-BT screw-in stainless steel and carbon steel threaded studs Product data Dimensions S-BT-MR M10/15 SN 6 S-BT-MR M10/15 SN 6 AL**) S-BT-MR W10/15 SN 6 S-BT-MR W10/15 SN 6 AL**) S-BT-MR M10/15 SN 5 ***)
More informationPHASED OUT. LED Driver Linear / area fixed output. Driver LCI 20W 150mA 400mA TOP lp TOP series. Product description
Product description EL Fixed output built-in LED Driver Constant current LED Driver Output current settable 150 400 ma Max. output power 20 W Nominal life-time up to 100,000 h For luminaires of protection
More informationTESTRANSFO2 User s Guide
TESTRANSFO2 User s Guide Avril 2015 MADE - V 1.14 M A D E S.A. au capital de 270 130 167, Impasse de la garrigue F 83210 LA FARLEDE Tél:+ 33 (0) 494 083 198 FAX : + 33 (0) 494 082 879 E-mail: contact@made-sa.com
More informationInstruction manual ZSH 2090
Zehntner GmbH Testing Instruments Gewerbestrasse 4 CH-4450 Sissach Switzerland Tel +41 (0)61 953 05 50 Fax +41 (0)61 953 05 51 zehntner@zehntner.com www.zehntner.com Instruction manual version 3.8 dated
More information30th European Conference on Acoustic Emission Testing & 7th International Conference on Acoustic Emission University of Granada, 12-15 September 2012 www.ndt.net/ewgae-icae2012/ Qualification of the acoustic
More informationPHASED OUT. LED Driver Compact fixed output. Driver LCI 20W 350mA 900mA TOP C TOP series
EL Product description Fixed output built-in LED Driver Constant current LED Driver Output current settable 30 900 ma Max. output power 20 W Nominal life-time up to 100,000 h For luminaires of protection
More informationPHASED OUT. LED Driver Compact fixed output. Driver LCI 10W 150mA 400mA TOP C TOP series. Product description
Product description EL Fixed output built-in LED Driver Constant current LED Driver Output current settable 15 4 ma Max. output power W Nominal life-time up to, h For luminaires of protection class I and
More informationHandling and Electrical Contacting of Piezoceramic Components
Technical Note Handling and Electrical Contacting of Piezoceramic Components Contents About this Document... 2 Symbols and Typographic Conventions... 2 Safety Instructions... 2 Personnel Qualification...
More informationTEST PROCEDURE FOR DYNAMIC PULL-THROUGH PERFORMANCE OF ROOFING MEMBRANES OVER FASTENER HEADS OR FASTENERS WITH METAL BEARING PLATES
TESTING APPLICATION STANDARD (TAS) 117(B)-95 TEST PROCEDURE FOR DYNAMIC PULL-THROUGH PERFORMANCE OF ROOFING MEMBRANES OVER FASTENER HEADS OR FASTENERS WITH METAL BEARING PLATES 1. Scope 1.1 This Protocol
More informationCertified Reference Materials for UV, Visible, NIR and IR Molecular Spectroscopy
Certified Reference Materials for UV, Visible, NIR and IR Molecular Spectroscopy RM-1N3N5DHG Set Serial No: 23135 Customer Details: Starna Cells Inc 5950 Traffic Way Atascadero CA 93422 U.S.A. The customer
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-24222-0 Edition 3 ISO 898-1:2009 Edition 4 SOUTH AFRICAN NATIONAL STANDARD Fasteners Part 5: General requirements and mechanical properties Section 1: Mechanical properties of fasteners
More informationTests according to standard UNE EN 14465:2004 / A1:2007: TEXTILE UPHOLSTERY FABRIC. Specification and method of test
The test/s herein contained has or have been performed under the criteria of Good Environmental Practices, considering the minimization of natural resources consumption, reduction of waste generation and
More informationTEST REPORT EN 62233: 2008 Measurement methods for electromagnetic fields of household appliances and similar apparatus with regard to human exposure
TEST REORT Measurement methods for electromagnetic fields of household appliances and similar apparatus with regard to human exposure Report Reference No....: GZES110400210331 Tested by (name + signature)...:
More informationDouble Shear Testing of Bolts
University of Wollongong Research Online Coal Operators' Conference Faculty of Engineering and Information Sciences 23 Double Shear Testing of Bolts N. Aziz University of Wollongong, naj@uow.edu.au D.
More informationLED Driver Compact dimming
Driver LCA 1W 45mA phase-cut 22mm SR ADV ADVANCED series Product description Dimmable constant current LED driver (SELV) Independent driver with strain-relief housing Extra flat housing for constrained
More informationTested and ready to use Quality from a single-source
Tested and ready to use Quality from a single-source 2 Cable fabrication 100% tested and ready to use for all-round certainty Quickly assembled and reliable in operation that is how machine components
More informationPHASED OUT. LED Driver Compact fixed output. Driver LCI 10W 350mA 900mA TOP C TOP series
EL Product description Fixed output built-in LED Driver Constant current LED Driver Output current settable 35 9 ma Max. output power W Nominal life-time up to, h For luminaires of protection class I and
More informationSteel Gauge Block Sets Page 341. Steel individual Gauge Blocks Page 348. CERA Gauge Block Sets Page 350. CERA Individual Gauge Blocks Page 353
Gauge Steel Gauge Block Sets Page 3 Steel individual Gauge Page 38 CERA Gauge Block Sets Page 35 CERA Individual Gauge Page 353 Special Gauge Page 35 Accessories for Gauge Page 356 3 All products to be
More informationStandard Specification for Carbon and Alloy Steel Nuts [Metric] 1
Designation: A 563M 04 METRIC Standard Specification for Carbon and Alloy Steel Nuts [Metric] 1 This standard is issued under the fixed designation A 563M; the number immediately following the designation
More informationMOY/SCMI/60 SPECIFICATION OF ACCURACY FOR VEE PIECES FOR EXTERNAL SCREW THREAD MEASUREMENT
Centre for Basic, Thermal and Length Metrology National Physical Laboratory MOY/SCMI/60 SPECIFICATION OF ACCURACY FOR VEE PIECES FOR EXTERNAL SCREW THREAD MEASUREMENT Hardened steel vee pieces, for use
More informationCopyright. Michael Joseph Gilroy. May 1997
Copyright by Michael Joseph Gilroy May 1997 Tightening of High Strength Metric Bolts by Michael Joseph Gilroy, B.S. Thesis Presented to the Faculty of the Graduate School of The University of Texas at
More informationISO 7438 INTERNATIONAL STANDARD. Metallic materials Bend test. Matériaux métalliques Essai de pliage. Second edition
INTERNATIONAL STANDARD ISO 7438 Second edition 2005-06-15 Metallic materials Bend test Matériaux métalliques Essai de pliage Reference number ISO 7438:2005(E) ISO 2005 PDF disclaimer This PDF file may
More informationT e s t R e p o r t. Page 1 of 6
T e s t R e p o r t Report No : L16220B Client: : QVIS Jones Avens 53 Kent Road Southsea Portsmouth Hampshire PO5 3HU Description : 2.5 Micro prism PC Manufacturer : Not disclosed Type/Model : DIF-MPC
More informationSCOPE OF ACCREDITATION TO ISO/IEC 17025:2005
SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 FASTENAL COMPANY LABORATORY - TAIWAN 1 434 Gangshan Road, 5 th Floor, Suite D Gangshan District, Kaoshiung City, TAIWAN 820 R.O.C. Brad Partington Phone: 507
More informationCertificate of Accreditation
PERRY JOHNSON LABORATORY ACCREDITATION, INC. Certificate of Accreditation Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of: Acceso III No. 16 A Nave 10, Parque Industrial Benito
More informationDatasheet. Variable Impact Tester. Elcometer 1615
Variable Impact Tester This simple to use gauge is ideal for evaluating the resistance of a coating to impact (elongation, cracking or peeling), and is suitable for use on both direct and indirect test
More informationU15. Force transducer. Special features. Data sheet. Installed dimensions of connection variants
U15 Force transducer Special features - Tensile/compressive force transducer - Nominal (rated) forces 2.5 kn to 2.5 MN - lass 0.5 to ISO 376 in force measurement range between 10% and 100% of the nominal
More informationUPDATE TO STANDARD EN 388 GLOVES GIVING PROTECTION FROM MECHANICAL RISKS
UPDATE TO STANDARD EN 388 GLOVES GIVING PROTECTION FROM MECHANICAL RISKS EN 388 THIS STANDARD APPLIES TO ALL KINDS OF PROTECTIVE GLOVES IN RESPECT OF PHYSICAL AND MECHANICAL AGGRESSIONS CAUSED BY ABRASION,
More informationSecurifor Polyester Coated Welded Mesh Panels
1 Scope This specification specifies requirements for panels made out of galvanised steel wires, welded and subsequently polyester coated for fencing. The panels are used for fencing, schools, public buildings,
More informationStructural Strength of Lapped Cold-Formed Steel Z-Shaped Purlin Connections with Vertical Slotted Holes
Missouri University of Science and Technology Scholars' Mine International Specialty Conference on Cold- Formed Steel Structures (2014) - 22nd International Specialty Conference on Cold-Formed Steel Structures
More information