Ultrasonics. Introduction
|
|
- Bruno Clarke
- 5 years ago
- Views:
Transcription
1 Ultrasonics Introduction Ultrasonics is the term used to describe those sound waves whose frequency is above the audible range of human ear upward from approximately 20kHz to several MHz. The ultrasonics in this experiment is generated by a transducer made of piezoelectric crystal. The crystal is set into oscillation by the oscillatory electric field produced by the electronic oscillator. The Phywe generator used in this experiment has two modes of operation: continuous wave (CW) at around 800kHz and repetitive pulses. Experimental Setup The equipment setup is shown schematically below. Note that the transducer should be immersed in water at all times to prevent it from being overheated. Error Analysis The first experiment is suitable to demonstrate the normal distribution of data, and to refresh your knowledge of error analysis. See appendix below for Standard deviation and Standard error of the mean. While the analysis can be easily calculated by a handheld calculator, you are required to explain the concept as well as the mathematics of standard deviation, and to calculate the propagation of errors. 1
2 Experiment 1 Velocity Measurement The frequency f, wavelength λ, and velocity v of a sound beam, are related by v = λ f. From this relationship, knowing the frequency and wavelength the velocity of sound in water can be deduced. The ultrasonic frequency of the oscillator (in CW) driving the transducer can be determined by an oscilloscope, or better still by a frequency meter. The wavelength is determined by the lines of stationary bubbles (cavitations at the pressure minima) formed in the water. In order that the bubbles are stationary, the standing wave condition must be first established. For best result adjust the aluminium reflector for a strong standing wave, which is indirectly visible as parallel lines of fine bubbles perpendicular to the direction of the ultrasonic beam. Typically the aluminium reflector is position at a distance of less than 15 cm from the transducer. The separation between the bubbles is 1 2 λ. A travelling microscope with digital readout is used for measuring the separation. To facilitate better viewing of the bubbles a table lamp should be used to illuminate the bubbles. 1. Take at least 25 readings at different parts along the ultrasonic beam. Plot the distribution to verify that you have enough statistics for a normal distribution. Find the standard deviation by: (a) hand-held calculator, and (b) from your normal distribution graph. Verify that they agree according to error analysis theory. 2. Work out the mathematics for error propagation. Estimate the standard deviation and standard error of the mean of the velocity. What is the sample size needed to have a 95% confidence level? 3. It is well know that the velocity of sound is basically determined by the modulus of elasticity, K, of water. The expression can easily be found with the aid of Newton's second law as: v = K / ρ where ρ is the density of water and for our purpose may be taken as 1g/cm Calculate the standard deviation of your K value. 4. Explain why a standing wave is a necessary condition in this experiment, and the steps you have taken to ensure that the condition is met. 3 2
3 Experiment 2 SONAR Use the pulse mode of the ultrasonic generator for a demonstration of distance measurement with SONAR (Sound, Navigation and Ranging). Place the aluminium reflector at various distances from the transducer. Align the receiving sensor so that it is facing the incoming reflected pulses. The sensor should be rigidly clamped and pick-up signal, which is weak, sent to the oscilloscope set at high gain input. The ultrasonic generator also gives a reference pulse as marker of time frame. Connect the reference pulse to the other channel of the oscilloscope. For a stable display without jitters, adjust the triggering level to bring the ultrasonic oscillator sweeping rate and the scope into synchronisation. 1. Use a digital camera to take the traces of original and reflected (echoes) pulses for a number of different distances. 2. Using the oscilloscope, measure accurately the time separation between the original pulse and the reflected echoes, hence deduce the distance travelled. 3. Confirm your results by comparing them with a ruler measurement, taking care to allow for a slightly skew path of the pulses. Plot a graph of the ultrasonic measurement versus ruler measurement. Discuss the accuracy of your measurement. 4. Give the reason(s) that SONAR is employed in underwater by submarines and fishing boats rather than the highly accurate electromagnetic waves. Figure 1 Original and reflected (echoes) pulses for 0.3m reflection Figure 2 Original and reflected (echoes) pulses for 0.2m reflection 3
4 Appendix Appendix - Standard Error of the Mean When trying to work out the mean of a sample, we may have to answer one of two questions: If there is no control over the size of the sample, what is the confidence of the mean. If the size of the sample can be controlled, how big a sample should be taken to ensure that the confidence interval is within the required limits. The solution is based on the standard error of the mean. The distribution of sample means is normally distributed, regardless of the distribution of the population from which the sample was drawn. The standard error of the mean is the standard deviation of the sample mean. The formula is: It follows from this equation, that the larger the sample size, the smaller the likely error. This is one of those cases where statistics tells you something that is intuitively obvious. In practice we don't always know the standard deviation of the population (or a value calculated from a very large sample), so we may have to estimate the value from the sample. The confidence limits of the sample mean are: Example - Confidence Interval for the Mean. The standard deviation of the weight of individual chilies from this years crop was 2.0 grams. The average weight of a sample of 16 chilies was 10 grams. Thus the standard error of the mean is: StErr = 2/ 16 = 0.5 Therefore the 95% confidence interval for the mean is: Confidence interval = 10 ± 1.96 * 0.5 = 10 ± 0.98 = 9.02 to Sample Size The formula for the standard error can be re-arranged to estimate the required sample size: 4
5 Thus if we know the confidence level and the interval size, we can work out the standard error to plug into the equation: Example - Sample Size Back to our crop of chilies, say, we need to be 95% certain that our estimate of the mean has an error of plus or minus 0.50 grams, how big should the sample be. Step 1 - Calculate the standard error StErr = interval/1.96 = 0.5/1.96 = 0.26 Step 2 - Work out the sample size n = (StDev/StErr) 2 = (2.00/0.26) 2 = = 59.1 In practice, we would take the next integer value which is greater then 59.1, i.e. 60 as the required sample size. 5
BANNARI AMMAN INSTITUTE OF TECHNOLOGY SATHYAMANGALAM DEPARTMENT OF PHYSICAL SCIENCES Unit III ULTRASONICS
A1 A2 A3 A4 A5 A6 A7 A8 A9 BANNARI AMMAN INSTITUTE OF TECHNOLOGY SATHYAMANGALAM DEPARTMENT OF PHYSICAL SCIENCES Unit III ULTRASONICS Multiple Choice Questions Loudspeaker cannot produce ultrasonic waves
More informationINTERFERENCE OF SOUND WAVES
01/02 Interference - 1 INTERFERENCE OF SOUND WAVES The objectives of this experiment are: To measure the wavelength, frequency, and propagation speed of ultrasonic sound waves. To observe interference
More informationPhysics Spring 2006 Experiment 9 TRAVELING WAVES
Physics 31210 Spring 2006 Experiment 9 TRAVELING WAVES Reference: Halliday, Resnick & Walker, 7th Ed., Sections 16-1 to 5, Sections 17-1 to 4 I. Introduction: Waves of all kinds, propagating through many
More informationMeasuring Distance Using Sound
Measuring Distance Using Sound Distance can be measured in various ways: directly, using a ruler or measuring tape, or indirectly, using radio or sound waves. The indirect method measures another variable
More informationMeasuring the speed of light
1 Purpose and comments Determine the speed of light by sending a laser beam through various mediums. Unless you want to see like Helen Keller, do not place your eyes in the beam path. Also, Switch the
More informationExperiment-4 Study of the characteristics of the Klystron tube
Experiment-4 Study of the characteristics of the Klystron tube OBJECTIVE To study the characteristics of the reflex Klystron tube and to determine the its electronic tuning range EQUIPMENTS Klystron power
More informationMicrowave Diffraction and Interference
Microwave Diffraction and Interference Department of Physics Ryerson University rev.2014 1 Introduction The object of this experiment is to observe interference and diffraction of microwave radiation,
More informationExercise 1-3. Radar Antennas EXERCISE OBJECTIVE DISCUSSION OUTLINE DISCUSSION OF FUNDAMENTALS. Antenna types
Exercise 1-3 Radar Antennas EXERCISE OBJECTIVE When you have completed this exercise, you will be familiar with the role of the antenna in a radar system. You will also be familiar with the intrinsic characteristics
More informationLab M6: The Doppler Effect
M6.1 Lab M6: The Doppler Effect Introduction The purpose in this lab is to teach the basic properties of waves (amplitude, frequency, wavelength, and speed) using the Doppler effect. This effect causes
More informationSonic Distance Sensors
Sonic Distance Sensors Introduction - Sound is transmitted through the propagation of pressure in the air. - The speed of sound in the air is normally 331m/sec at 0 o C. - Two of the important characteristics
More informationHUYGENS PRINCIPLE AND INTERFERENCE
HUYGENS PRINCIPLE AND INTERFERENCE VERY SHORT ANSWER QUESTIONS Q-1. Can we perform Double slit experiment with ultraviolet light? Q-2. If no particular colour of light or wavelength is specified, then
More informationFRAUNHOFER AND FRESNEL DIFFRACTION IN ONE DIMENSION
FRAUNHOFER AND FRESNEL DIFFRACTION IN ONE DIMENSION Revised November 15, 2017 INTRODUCTION The simplest and most commonly described examples of diffraction and interference from two-dimensional apertures
More information7. Experiment K: Wave Propagation
7. Experiment K: Wave Propagation This laboratory will be based upon observing standing waves in three different ways, through coaxial cables, in free space and in a waveguide. You will also observe some
More informationPHYS2090 OPTICAL PHYSICS Laboratory Microwaves
PHYS2090 OPTICAL PHYSICS Laboratory Microwaves Reference Hecht, Optics, (Addison-Wesley) 1. Introduction Interference and diffraction are commonly observed in the optical regime. As wave-particle duality
More informationStanding waves in the microwave range
Related topics Microwaves, electromagnetic waves, reflection, inverse square law Principle If electromagnetic waves are reflected to and fro between two reflectors, a standing wave results. The wavelength
More informationAnswer:- School bell starts vibrating when heated which creates compression and rarefaction in air and sound is produced.
Sound How does the sound produced by a vibrating object in a medium reach your ear? - Vibrations in an object create disturbance in the medium and consequently compressions and rarefactions. Because of
More informationLesson 02: Sound Wave Production. This lesson contains 24 slides plus 11 multiple-choice questions.
Lesson 02: Sound Wave Production This lesson contains 24 slides plus 11 multiple-choice questions. Accompanying text for the slides in this lesson can be found on pages 2 through 7 in the textbook: ULTRASOUND
More information3.003 Lab 3 Part A. Measurement of Speed of Light
3.003 Lab 3 Part A. Measurement of Speed of Light Objective: To measure the speed of light in free space Experimental Apparatus: Feb. 18, 2010 Due Mar. 2, 2010 Components: 1 Laser, 4 mirrors, 1 beam splitter
More informationNCERT solution for Sound
NCERT solution for Sound 1 Question 1 How does the sound produce by a vibrating object in a medium reach your ear? When an object vibrates, it vibrates the neighboring particles of the medium. These vibrating
More informationSpeed of Light in Air
Speed of Light in Air Introduction Light can travel a distance comparable to seven and one-half times around the Earth in one second. The first accurate measurements of the speed of light were performed
More informationAns: A wave is periodic disturbance produced by vibration of the vibrating. 2. What is the amount of sound energy passing per second through unit area
One mark questions 1. What do you understand by sound waves? Ans: A wave is periodic disturbance produced by vibration of the vibrating body. 2. What is the amount of sound energy passing per second through
More informationPhysics 4C Chabot College Scott Hildreth
Physics 4C Chabot College Scott Hildreth The Inverse Square Law for Light Intensity vs. Distance Using Microwaves Experiment Goals: Experimentally test the inverse square law for light using Microwaves.
More informationStudy of Standing Waves to Find Speed of Sound in Air
Study of Standing Waves to Find Speed of Sound in Air Purpose Using mobile devices as sound analyzer and sound generator to study standing waves and determine the speed of sound in air. Theory The velocity
More informationExercise 2: Distance Measurement
Transducer Fundamentals Ultrasonic Transducers Exercise 2: Distance Measurement EXERCISE OBJECTIVE At the completion of this exercise, you will be able to explain and demonstrate the operation of ultrasonic
More informationContinuous Wave Radar
Continuous Wave Radar CW radar sets transmit a high-frequency signal continuously. The echo signal is received and processed permanently. One has to resolve two problems with this principle: Figure 1:
More informationDiwali Holiday Homework Class IX A
Diwali Holiday Homework - 2017 Class IX A Subject English Hindi Mathematics Physics Chemistry Diwali Break Homework Refer to Page 20 in your Student Book. The last point in the Writing Task says: Taking
More informationLab 2. Logistics & Travel. Installing all the packages. Makeup class Recorded class Class time to work on lab Remote class
Lab 2 Installing all the packages Logistics & Travel Makeup class Recorded class Class time to work on lab Remote class Classification of Sensors Proprioceptive sensors internal to robot Exteroceptive
More informationResonance Tube. 1 Purpose. 2 Theory. 2.1 Air As A Spring. 2.2 Traveling Sound Waves in Air
Resonance Tube Equipment Capstone, complete resonance tube (tube, piston assembly, speaker stand, piston stand, mike with adapters, channel), voltage sensor, 1.5 m leads (2), (room) thermometer, flat rubber
More informationAcoustic Velocity Independent Ultrasonic Flow-Meter
flotek.g 2017- Innovative Solutions in Flow Measurement and Control - Oil, Water and Gas August 28-30, 2017, FCRI, Palakkad, Kerala, India Acoustic Velocity Independent Ultrasonic Flow-Meter ABSTRACT Shalini
More informationINTRODUCTION. Have applications for imaging, detection and navigation.
ULTRASONICS INTRODUCTION The word ultrasonic combines the Latin roots ultra - beyond sonic - sound. Having frequencies above the audible range i.e. above 20000Hz Have applications for imaging, detection
More informationENGR1 Antenna Pattern Measurements
ENGR1 Antenna Pattern Measurements November 29, 2006 Instructor: Dr. Milica Marković Office: Riverside Hall 3028 Email: milica@csus.edu Abstract In this lab we will calculate and measure antenna parameters.
More informationResonance Tube Lab 9
HB 03-30-01 Resonance Tube Lab 9 1 Resonance Tube Lab 9 Equipment SWS, complete resonance tube (tube, piston assembly, speaker stand, piston stand, mike with adaptors, channel), voltage sensor, 1.5 m leads
More informationDigital Land Surveying Dr. Jayanta Kumar Ghosh Department of Civil Engineering Indian Institute of Technology, Roorkee
Digital Land Surveying Dr. Jayanta Kumar Ghosh Department of Civil Engineering Indian Institute of Technology, Roorkee Lecture 21 Measurement of Distance Welcome students, this is the 21st lecture on digital
More informationRange Sensing strategies
Range Sensing strategies Active range sensors Ultrasound Laser range sensor Slides adopted from Siegwart and Nourbakhsh 4.1.6 Range Sensors (time of flight) (1) Large range distance measurement -> called
More informationName: Lab Partner: Section:
Chapter 11 Wave Phenomena Name: Lab Partner: Section: 11.1 Purpose Wave phenomena using sound waves will be explored in this experiment. Standing waves and beats will be examined. The speed of sound will
More informationResonance Tube. 1 Purpose. 2 Theory. 2.1 Air As A Spring. 2.2 Traveling Sound Waves in Air
Resonance Tube Equipment Capstone, complete resonance tube (tube, piston assembly, speaker stand, piston stand, mike with adaptors, channel), voltage sensor, 1.5 m leads (2), (room) thermometer, flat rubber
More informationThe Discussion of this exercise covers the following points:
Exercise 3-2 Frequency-Modulated CW Radar EXERCISE OBJECTIVE When you have completed this exercise, you will be familiar with FM ranging using frequency-modulated continuous-wave (FM-CW) radar. DISCUSSION
More informationScope. Here are the times schedule of the pulse-echo technique detect method. Reflect pulse. Emit detect pulse (Ultrasound)
Abstract There is so many blind persons that use a blind stick to help their dally walking or life. But the blind stick will be hit some person when the blind stick waggling. So there is need to develop
More informationSpring 2004 M2.1. Lab M2. Ultrasound: Interference, Wavelength, and Velocity
Spring 2004 M2.1 Lab M2. Ultrasound: Interference, Wavelength, and Velocity The purpose in this lab exercise is to become familiar with the properties of waves: frequency, wavelength, phase and velocity.
More informationPart 1: Standing Waves - Measuring Wavelengths
Experiment 7 The Microwave experiment Aim: This experiment uses microwaves in order to demonstrate the formation of standing waves, verifying the wavelength λ of the microwaves as well as diffraction from
More informationUltrasonic Guided Wave Testing of Cylindrical Bars
18th World Conference on Nondestructive Testing, 16-2 April 212, Durban, South Africa Ultrasonic Guided Wave Testing of Cylindrical Bars Masanari Shoji, Takashi Sawada NTT Energy and Environment Systems
More informationTeacher s notes Induction of a voltage in a coil: A set of simple investigations
Faraday s law Sensors: Loggers: Voltage An EASYSENSE capable of fast recording Logging time: 200 ms Teacher s notes Induction of a voltage in a coil: A set of simple investigations Read This activity is
More informationBike Generator Project
Bike Generator Project Each lab section will build 1 bike generator Each lab group will build 1 energy board Connect and test energy board and bike generator Create curriculum materials and demos to teach
More information... frequency, f speed, v......
PhysicsAndMathsTutor.com 1 1. Define the terms wavelength, frequency and speed used to describe a progressive wave. wavelength, λ... frequency, f... speed, v... Hence derive the wave equation v = fλ which
More informationLab 12 Microwave Optics.
b Lab 12 Microwave Optics. CAUTION: The output power of the microwave transmitter is well below standard safety levels. Nevertheless, do not look directly into the microwave horn at close range when the
More informationSingle-photon excitation of morphology dependent resonance
Single-photon excitation of morphology dependent resonance 3.1 Introduction The examination of morphology dependent resonance (MDR) has been of considerable importance to many fields in optical science.
More informationPhysics 476LW. Advanced Physics Laboratory - Microwave Optics
Physics 476LW Advanced Physics Laboratory Microwave Radiation Introduction Setup The purpose of this lab is to better understand the various ways that interference of EM radiation manifests itself. However,
More information1 Diffraction of Microwaves
1 Diffraction of Microwaves 1.1 Purpose In this lab you will investigate the coherent scattering of electromagnetic waves from a periodic structure. The experiment is a direct analog of the Bragg diffraction
More informationPhys Homework Set 1 Fall 2015 Exam Name
Exam Name MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question. 1) Which of the following is a children s drawing toy that uses a circle within a circle
More informationChapter 5. Clock Offset Due to Antenna Rotation
Chapter 5. Clock Offset Due to Antenna Rotation 5. Introduction The goal of this experiment is to determine how the receiver clock offset from GPS time is affected by a rotating antenna. Because the GPS
More informationIntext Exercise 1 Question 1: How does the sound produced by a vibrating object in a medium reach your ear?
Intext Exercise 1 How does the sound produced by a vibrating object in a medium reach your ear? When an vibrating object vibrates, it forces the neighbouring particles of the medium to vibrate. These vibrating
More informationPH 0101 UNIT 1 LECTURE 6
PH 0101 UNIT 1 LECTURE 6 Introduction to Ultrasonics Properties of Ultrasonic waves Ultrasonic Production- Magnetostriction Method Ultrasonic Production- Piezo Electric Method Applications of Ultrasonics
More informationGoals of the Lab: Photodetectors and Noise (Part 2) Department of Physics. Slide 1. PHYSICS6770 Laboratory 4
Slide 1 Goals of the Lab: Understand the origin and properties of thermal noise Understand the origin and properties of optical shot noise In this lab, You will qualitatively and quantitatively determine
More informationCoil in the AC circuit
Coil in the AC circuit LEP Related topics Inductance, Kirchhoff s laws, parallel connection, series connection, a. c. impedance, phase displacement, vector diagram Principle The impedance and phase displacement
More informationSupplementary Information
Supplementary Information Supplementary Figure 1. Modal simulation and frequency response of a high- frequency (75- khz) MEMS. a, Modal frequency of the device was simulated using Coventorware and shows
More informationPh 2306 Experiment 2: A Look at Sound
Name ID number Date Lab CRN Lab partner Lab instructor Ph 2306 Experiment 2: A Look at Sound Objective Because sound is something that we can only hear, it is difficult to analyze. You have probably seen
More informationEECE208 INTRO To ELECTRICAL ENG LAB. LAB 2. Instrumentation
EECE208 INTRO To ELECTRICAL ENG LAB Dr. Charles Kim LAB 2. Instrumentation Objectives A brief description of the equipment (Oscilloscope, Function Generator, Power Supply, and Digital Multimeter) and its
More informationRapidScan II Application Note General Composite Scanning
RapidScan II Application Note General Composite Scanning RapidScan II General Composite Scanning Application Note Page 1 Applications The RapidScan system has been utilised for a wide range of inspections
More information6 Experiment II: Law of Reflection
Lab 6: Microwaves 3 Suggested Reading Refer to the relevant chapters, 1 Introduction Refer to Appendix D for photos of the apparatus This lab allows you to test the laws of reflection, refraction and diffraction
More informationExercise 1-4. The Radar Equation EXERCISE OBJECTIVE DISCUSSION OUTLINE DISCUSSION OF FUNDAMENTALS
Exercise 1-4 The Radar Equation EXERCISE OBJECTIVE When you have completed this exercise, you will be familiar with the different parameters in the radar equation, and with the interaction between these
More informationDevantech SRF04 Ultra-Sonic Ranger Finder Cornerstone Electronics Technology and Robotics II
Devantech SRF04 Ultra-Sonic Ranger Finder Cornerstone Electronics Technology and Robotics II Administration: o Prayer PicBasic Pro Programs Used in This Lesson: o General PicBasic Pro Program Listing:
More informationSECOND HARMONIC GENERATION AND Q-SWITCHING
SECOND HARMONIC GENERATION AND Q-SWITCHING INTRODUCTION In this experiment, the following learning subjects will be worked out: 1) Characteristics of a semiconductor diode laser. 2) Optical pumping on
More informationExp No.(8) Fourier optics Optical filtering
Exp No.(8) Fourier optics Optical filtering Fig. 1a: Experimental set-up for Fourier optics (4f set-up). Related topics: Fourier transforms, lenses, Fraunhofer diffraction, index of refraction, Huygens
More informationAP Physics Problems -- Waves and Light
AP Physics Problems -- Waves and Light 1. 1974-3 (Geometric Optics) An object 1.0 cm high is placed 4 cm away from a converging lens having a focal length of 3 cm. a. Sketch a principal ray diagram for
More informationTektronix digital oscilloscope, BK Precision Function Generator, coaxial cables, breadboard, the crystal earpiece from your AM radio kit.
Experiment 0: Review I. References The 174 and 275 Lab Manuals Any standard text on error analysis (for example, Introduction to Error Analysis, J. Taylor, University Science Books, 1997) The manual for
More informationPhysics of ultrasound
1 Physics of ultrasound Basic principles Nature of ultrasound Sound = longitudinal, mechanical wave particles move parallel to direction of travel Audible sound < 20 khz Ultrasound > 20 khz Sound cannot
More informationPHYSICS 107 LAB #3: WAVES ON STRINGS
Section: Monday / Tuesday (circle one) Name: Partners: Total: /40 PHYSICS 107 LAB #3: WAVES ON STRINGS Equipment: Function generator, amplifier, driver, elastic string, pulley and clamp, rod and table
More informationPHYS102 Previous Exam Problems. Sound Waves. If the speed of sound in air is not given in the problem, take it as 343 m/s.
PHYS102 Previous Exam Problems CHAPTER 17 Sound Waves Sound waves Interference of sound waves Intensity & level Resonance in tubes Doppler effect If the speed of sound in air is not given in the problem,
More informationDr. P. SREENIVASULU REDDY 2
ENGINEERING PHYSICS UNIT II - ULTRASONICS SV COLLEGE OF ENGINEERING, KADAPA Syllabus: - Introduction - Production of ultrasonic's by piezoelectric method - Properties and detection Applications in non-destructive
More informationMomentum and Impulse. Objective. Theory. Investigate the relationship between impulse and momentum.
[For International Campus Lab ONLY] Objective Investigate the relationship between impulse and momentum. Theory ----------------------------- Reference -------------------------- Young & Freedman, University
More informationLaboratory Exercise 6 THE OSCILLOSCOPE
Introduction Laboratory Exercise 6 THE OSCILLOSCOPE The aim of this exercise is to introduce you to the oscilloscope (often just called a scope), the most versatile and ubiquitous laboratory measuring
More informationExperiment P20: Driven Harmonic Motion - Mass on a Spring (Force Sensor, Motion Sensor, Power Amplifier)
PASCO scientific Physics Lab Manual: P20-1 Experiment P20: - Mass on a Spring (Force Sensor, Motion Sensor, Power Amplifier) Concept Time SW Interface Macintosh file Windows file harmonic motion 45 m 700
More informationThe Physics of Echo. The Physics of Echo. The Physics of Echo Is there pericardial calcification? 9/30/13
Basic Ultrasound Physics Kirk Spencer MD Speaker has no disclosures to make Sound Audible range 20Khz Medical ultrasound Megahertz range Advantages of imaging with ultrasound Directed as a beam Tomographic
More informationConservation of energy during the reflection and transmission of microwaves
Related topics Microwaves, electromagnetic waves, reflection, transmission, polarisation, conservation of energy, conservation laws Principle When electromagnetic waves impinge on an obstacle, reflection,
More informationECE 185 ELECTRO-OPTIC MODULATION OF LIGHT
ECE 185 ELECTRO-OPTIC MODULATION OF LIGHT I. Objective: To study the Pockels electro-optic (E-O) effect, and the property of light propagation in anisotropic medium, especially polarization-rotation effects.
More informationStanding Waves. Miscellaneous Cables and Adapters. Capstone Software Clamp and Pulley White Flexible String
Partner 1: Partner 2: Section: Partner 3 (if applicable): Purpose: Continuous waves traveling along a string are reflected when they arrive at the (in this case fixed) end of a string. The reflected wave
More informationEECE208 INTRO To ELECTRICAL ENG LAB. LAB 2. Instrumentation
EECE208 INTRO To ELECTRICAL ENG LAB Dr. Charles Kim LAB 2. Instrumentation Objectives A brief description of the equipment (Oscilloscope, Function Generator, Power Supply, and Digital Multimeter) and its
More informationExperimental Question 2: An Optical Black Box
Experimental Question 2: An Optical Black Box TV and computer screens have advanced significantly in recent years. Today, most displays consist of a color LCD filter matrix and a uniform white backlight
More informationChapter 4. Pulse Echo Imaging. where: d = distance v = velocity t = time
Chapter 4 Pulse Echo Imaging Ultrasound imaging systems are based on the principle of pulse echo imaging. These systems require the use of short pulses of ultrasound to create two-dimensional, sectional
More informationLab in a Box Microwave Interferometer
In 1887 Michelson and Morley used an optical interferometer (a device invented by Michelson to accurately detect aether flow) to try and detect the relative motion of light through the luminous either.
More informationPhased Array Velocity Sensor Operational Advantages and Data Analysis
Phased Array Velocity Sensor Operational Advantages and Data Analysis Matt Burdyny, Omer Poroy and Dr. Peter Spain Abstract - In recent years the underwater navigation industry has expanded into more diverse
More informationBroadband Temporal Coherence Results From the June 2003 Panama City Coherence Experiments
Broadband Temporal Coherence Results From the June 2003 Panama City Coherence Experiments H. Chandler*, E. Kennedy*, R. Meredith*, R. Goodman**, S. Stanic* *Code 7184, Naval Research Laboratory Stennis
More informationABC Math Student Copy
Page 1 of 17 Physics Week 9(Sem. 2) Name Chapter Summary Waves and Sound Cont d 2 Principle of Linear Superposition Sound is a pressure wave. Often two or more sound waves are present at the same place
More informationGeometric Optics. Objective: To study the basics of geometric optics and to observe the function of some simple and compound optical devices.
Geometric Optics Objective: To study the basics of geometric optics and to observe the function of some simple and compound optical devices. Apparatus: Pasco optical bench, mounted lenses (f= +100mm, +200mm,
More informationMechatronics Chapter Sensors 9-1
MEMS1049 Mechatronics Chapter Sensors 9-1 Proximity sensors and Switches Proximity sensor o o o A proximity sensor is a sensor able to detect the presence of nearby objects without any physical contact.
More informationCHAPTER 5 FINE-TUNING OF AN ECDL WITH AN INTRACAVITY LIQUID CRYSTAL ELEMENT
CHAPTER 5 FINE-TUNING OF AN ECDL WITH AN INTRACAVITY LIQUID CRYSTAL ELEMENT In this chapter, the experimental results for fine-tuning of the laser wavelength with an intracavity liquid crystal element
More informationMulti-spectral acoustical imaging
Multi-spectral acoustical imaging Kentaro NAKAMURA 1 ; Xinhua GUO 2 1 Tokyo Institute of Technology, Japan 2 University of Technology, China ABSTRACT Visualization of object through acoustic waves is generally
More information1. Introduction. 2. Concept. reflector. transduce r. node. Kraftmessung an verschiedenen Fluiden in akustischen Feldern
1. Introduction The aim of this Praktikum is to familiarize with the concept and the equipment of acoustic levitation and to measure the forces exerted by an acoustic field on small spherical objects.
More informationA novel procedure for evaluating the rotational stiffness of traditional timber joints in Taiwan
Structural Studies, Repairs and Maintenance of Heritage Architecture IX 169 A novel procedure for evaluating the rotational stiffness of traditional timber joints in Taiwan W.-S. Chang, M.-F. Hsu & W.-C.
More informationSPRAY DROPLET SIZE MEASUREMENT
SPRAY DROPLET SIZE MEASUREMENT In this study, the PDA was used to characterize diesel and different blends of palm biofuel spray. The PDA is state of the art apparatus that needs no calibration. It is
More informationHOW FAR AWAY ARE THE SATELLITES?
HOW FAR AWAY ARE THE SATELLITES? Concepts A signal is a wave Wave characteristics can be used to measure properties such as velocity, distance, and time Every measurement has units Units are interchangeable
More informationProperties of Sound. Goals and Introduction
Properties of Sound Goals and Introduction Traveling waves can be split into two broad categories based on the direction the oscillations occur compared to the direction of the wave s velocity. Waves where
More informationR. J. Jones College of Optical Sciences OPTI 511L Fall 2017
R. J. Jones College of Optical Sciences OPTI 511L Fall 2017 Active Modelocking of a Helium-Neon Laser The generation of short optical pulses is important for a wide variety of applications, from time-resolved
More informationElizabethtown College Department of Physics and Engineering PHY104. Lab # 9- Oscilloscope and RC Circuit
Elizabethtown College Department of Physics and Engineering PHY104 Lab # 9- Oscilloscope and RC Circuit Introduction This lab introduces you to very important tools, the oscilloscope and the waveform generator.
More informationOscilloscope and Function Generators
MEHRAN UNIVERSITY OF ENGINEERING AND TECHNOLOGY, JAMSHORO DEPARTMENT OF ELECTRONIC ENGINEERING ELECTRONIC WORKSHOP # 02 Oscilloscope and Function Generators Roll. No: Checked by: Date: Grade: Object: To
More informationCHAPTER 11 TEST REVIEW -- MARKSCHEME
AP PHYSICS Name: Period: Date: 50 Multiple Choice 45 Single Response 5 Multi-Response Free Response 3 Short Free Response 2 Long Free Response MULTIPLE CHOICE DEVIL PHYSICS BADDEST CLASS ON CAMPUS AP EXAM
More informationTHE CATHODE RAY OSCILLOSCOPE
The Department of Engineering SS1.2 THE CATHODE RAY OSCILLOSCOPE Objectives The objective of this laboratory is for you to familiarise yourself with the operation of a cathode ray oscilloscope (CRO). Once
More informationSteady State Operating Curve
Steady State Operating Curve By Lanze Berry University of Tennessee at Chattanooga Engineering 3280L Blue Team (Khanh Nguyen, Justin Cartwright) Course: ENGR 3280L Section: 001 Date: September 4, 2012
More informationHF Upgrade Studies: Characterization of Photo-Multiplier Tubes
HF Upgrade Studies: Characterization of Photo-Multiplier Tubes 1. Introduction Photomultiplier tubes (PMTs) are very sensitive light detectors which are commonly used in high energy physics experiments.
More information=, where f is focal length of a lens (positive for convex. Equations: Lens equation
Physics 1230 Light and Color : Exam #1 Your full name: Last First & middle General information: This exam will be worth 100 points. There are 10 multiple choice questions worth 5 points each (part 1 of
More information