Motor Controllers 3-Phase Analog Power Controller Types RSC-AAM60/RSO...

Transcription

1 otor Controllers 3-Phase nalog Controller Types RSC-60/RSO... Control and output modules for analogue control of 3-phase induction motors or heaters Rated operational current: 3 x, 25, 50, 90, 1 Crms Rated operational voltage: Up to 600 VCrms Supply voltage range: to 32 VDC Control current range: 0 to m/4 to m LED-indication for line ON and load ON Varistor protection pprovals: CE, CCC, UL, CS Product Description The micro processor based control module RSC-60 is used with output modules RSO... to achieve a voltage controlled soft start/soft stop of 3-phase motors and a possibility for energy reduction when e.g. a fan is running with a variable capacity. This function is achieved by controlling the control module with a current between 4 and m (0 and m). The output module can be selected according to the rated operational voltage and the size of the load. This phase angle controlled soft-start unit can be used for pumps, fans, heaters, lights and many other applications. LED indications for line ON and load ON gives a clear status indication. Ordering Key Solid State Relay Soft starting/stopping Control module Output module Control input type ultivoltage Rated operational voltage Rated operational current RSC- 60 RSO 4050 Type Selection, Control odule Control current ains ax. operational voltage Type Number 0- m/4- m ultivoltage 600 VC RSC- 60 Type Selection, Output odule Rated operational voltage Rated operational current x 2 VC RSO 22 RSO 2225 RSO 2250 RSO 2290 RSO x 400 VC RSO 40 RSO 4025 RSO 4050 RSO 4090 RSO x 480 VC RSO 48 RSO 4825 RSO 4850 RSO 4890 RSO x 600 VC RSO 6050 RSO 6090 RSO 601 General Spec., Control odule Operational voltage range Line to line 150 to 660 VCrms Operational frequency range 45 to 65 Hz Supply no output current < 30 max. output current < 180 m Supply voltage range to 32 VDC CE-marking Yes pprovals UL, CS, CCC Control Specifications inimum output voltage Output current short-circuit protected Thermal Specifications Operating temperature Storage temperature supply minus 8 VDC 150 m DC - to +70 C (-4 to +158 F) -40 to +0 C (-40 to +212 F) Specifications are subject to change without notice (26.03.) 1

2 RSC -60/RSO... Control Input Specifications Control current -input -input Input impedance supply reset time Response time (input to trigger outputs) Operation Diagram [%] 0 to m 4 to m 250 Ω 300 ms 1 cycle Urms/Un P/Pn Output as a function of control = 0.9 [m] Isolation Control odule Rated isolation voltage Input to trigger outputs ode of Operation The control module RSC- 60 is used with the output module RSO... to achieve analog control of 3- phase induction motors. Soft starting is achieved by increasing the motor voltage in accordance with the input current. Soft stopping is achieved by decreasing the motor voltage in accordance with the input current. When the motor is running idle, the motor voltage can be reduced by lowering the input current, whereby energy is saved VCrms Heating elements can also be controlled with the RSC/RSO with the use of appropriate filters. General Specifications, Output odule RSO RSO RSO RSO Operational voltage range Line to line 150 to 250 VCrms 2 to 4 VCrms 400 to 5 VCrms 400 to 625 VCrms locking voltage 10 V p 10 V p 10 V p 1600 V p Varistor voltage 275 VC 4 VC 5 VC 625 VC CE-marking Yes Yes Yes Yes Output Specifications, Output odule RSO.. RSO..25 RSO..50 RSO..90 RSO..1 IEC and CCC Rated Operational Current C rms 25 rms 50 rms 90 rms 1 rms IEC and CCC rated operational current C 53a 3 rms 5 rms 15 rms 30 rms 40 rms Number of C 7* 7* 7* 50* 50* Overload cycle according to EN/ IEC 40 C 3: C53a: 3: C53a: 3: C53a: 3: C53a: 3: C53a: 4-4:0-7* 4-4:0-7* 4-4: 0-7* 4-4:0-50* 4-4: 0-50* Off-state leakage current mrms mrms mrms 25 mrms 25 mrms On-state voltage drop 1.6 Vrms 1.6 Vrms 1.6 Vrms 1.8 Vrms 1.8 Vrms I 2 t for fusing t= ms s s s s s Non-rep. surge current t= ms 160 p 325 p 600 p 1150 p 1900 p * ounted on RHS Specifications are subject to change without notice (26.03.)

3 RSC -60/RSO... Thermal Specifications Output odule RSO.. RSO..25 RSO..50 RSO..90 RSO..1 Operating temperature - to +70 C - to +70 C - to +70 C - to +70 C - to +70 C (-4 to +158 F) (-4 to +158 F) (-4 to +158 F) (-4 to +158 F) (-4 to +158 F) Storage temperature -40 to +0 C -40 to +0 C -40 to +0 C -40 to +0 C -40 to +0 C (-40 to +212 F) (-40 to +212 F) (-40 to +212 F) (-40 to +212 F) (-40 to +212 F) Junction temperature 125 C 125 C 125 C 125 C 125 C R th junction to case 0.7 K/W 0.5 K/W 0.25 K/W 0.1 K/W 0.09 K/W Functional Diagram Wiring Diagram ounting and connection of control module Control input and output Supply ains input ON to m 4 to m output ccessories Supply/ Control input Heatsinks Fuses Temperature limit switch supply For further information refer to General ccessories. Dimensions RSO... RSC-60 Temperature limit switch Heat sink compound 39 2 = ± 0.4 mm = ± 0.5 mm ll dimensions in mm ll dimensions in mm Specifications are subject to change without notice (26.03.) 3

4 RSC -60/RSO... Heatsink Dimensions (load current versus ambient temperature) RSO.. RSO..25 [K/W] T mbient temp [K/W] T mbient temp. RSO [K/W] T mbient temp. Heatsink Selection Carlo Gavazzi Heatsink (see ccessories) No heatsink required RHS 300 ssy or backplate RHS 301 ssy RHS 301 F ssy Consult your distributor R th s-a > 8.0 K/W 5.0 K/W 0.8 K/W 0.25 K/W < 0.25 K/W RSO..90, RSO Heatsink/Thermal resistance [K/W] T mbient temp. Compare the value found in the load current versus temperature chart with the standard heatsink values and select the heatsink with the next lower value. It is recommended to protect the solid state relay against overheating. Therefore the chart also states the maximum switching temperature (70, 80 or 90 C) for the optional temperature limit switch. 4 Specifications are subject to change without notice (26.03.)

5 RSC -60/RSO... Housing Specifications Weight RSO..,..25,..50 RSO..90,..1 Housing material Colour ase 90 Potting compound pprox. 275 g pprox. 385 g Noryl, glass-reinforced lack luminium, nickel-plated Copper, nickel-plated Polyurethane, black Relay ounting screws 5 ounting torque 1.5 Nm Control terminal ounting screws 3 ounting torque 0.5 Nm terminal ounting screws 5 x 6 ounting torque 1.5 Nm pplications The output module RSO..1 is recommended for motors up to V. The RSO..1 is designed for use in applications with high surge current conditions. Care must be taken to ensure proper heatsinking when the relays are to be used at high nominal currents. dequate electrical connection between relay terminals and cable must be ensured. Example 1: dissipation - RSO 401: I load = 40 rms = 111 W See previous page. Example 2: otor: 3 kw, 4 HP 3 x 400 VC, 4-pole T : 50 C Starting time: 5 s For this application RSC-60 must be used. The output module RSO4025 is selected according to the Selection Guide. The smallest heatsink required is 1 K/W, and the power dissipation is 25 W. This gives: Control module: RSC-60 Output module: RSO 4025 Heatsink:1K/W Connection to the mains Since no motor protective circuitry is included in the RSC/RSO, the motor must be protected in the usual way, i.e. either by a thermal relay, a PTC-resistor or a Klixon bimetal temperature switch near the motor windings. If short circuit protection is required, fuses F1 to F3 should be ultrafast and selected according to the load integral (I 2 t) of the RSO output module and the motor load. 1/L1 3/L2 5/L3 2/T1 4/T2 6/T3 Pilot voltage Overload protection by thermal relay Transient voltage protection With an unfiltered main supply, voltage transient may occur. Since these transients could have a high energy content, it is advisable to use varistors to protect the output module. The varistors are already mounted in the RSO output module and they are selected according to the rated operational voltage. 1/L1 3/L2 5/L3 2/T1 4/T2 6/T3 Energy saving for motors in idle mode When motors are running idle, When the motor is idle, d1 will it not necessary to maintain a switch the control current from full magnetic field, as is the I 1 > m to I 2, which is case when the motor has to adjusted to a value at which produce full torque. y lowering the motor is still running at full the motor voltage, power speed, but at a lower voltage. losses inside the motor are Please remark that this type of also reduced. phase-angle controlled voltage reduction, demands additional filtering to fulfill EC regulations. 1/L1 3/L2 5/L3 R2 - I2 I1 + Stabilized voltage Ie Full/Id d1 Pilot voltage 2/T1 4/T2 6/T3 R1 GND Specifications are subject to change without notice (26.03.) 5

6 RSC -60/RSO... pplications (cont.) In order to achieve a 4 to m signal from a 12 or 24 VDC source, a resistor and a potentiometer should be connected in series with the voltage source and the RSC controller. We define the I max. to be e.g. 24 m, which means that the series resistors must be: R 1 (12 V) = U/I - Rint = 12 V/24 m Ω = 250 Ω R 1 (24 V) = U/I - Rint = 24 V/24 m Ω = 750 Ω If the minimum current is defined to be e.g. 2.4 m and the 250 Ω Rint input resistance of the RSC is also calculated in: R 2 (12 V) = U/I - R 1 - Rint = 12/ = 4500 Ω R 2 (24 V) = U/I - R 1 - Rint = 24/ = 9000 Ω Selection Guide 400 VCrms and 480 VCrms motors Output module RSO.. RSO..25 RSO..50 RSO..90 RSO..1 ax. motor size 3 HP/2.2 kw 5 HP/4 kw 15 HP/11 kw HP/15 kw 30 HP/22 kw 600 VCrms motors Output module RSO 6050 RSO 6090 RSO 601 ax. motor size 15 HP 30 HP 40 HP Wiring Diagram (0- VDC control) Short circuit Protection (according to EN/IEC ) RSO...25 RSO...50 RSO...90 RSO...1 RSO... Type of coordination: 2 Rated short circuit current 5k when protected 5k when protected 5k when protected 5k when protected by semiconductor fuses. by semiconductor fuses. by semiconductor fuses. by semiconductor fuses. Ferraz Shawmut 25, Ferraz Shawmut 63, Ferraz Shawmut 80, Ferraz Shawmut 0, Class URC rt. No. 6.9 CP Class URQ rt. No CP Class URQ rt. No CP ClassURQrt. No CP grc 14.51/ 25 URQ 27 x 60/ 63 URQ 27 x 60/ 80 URQ 27 x 60/ 0 6 Specifications are subject to change without notice (26.03.)