Unregulated power supplies
|
|
- Virginia Young
- 5 years ago
- Views:
Transcription
1 Contents Overview.2 compactpower /2015.1
2 Overview compactpower Compact power supply units are important links in the power supplies for controllers. They are used where processes or control voltages are required that vary from the mains voltage. Transformers provide the electrical isolation between the input circuit and the output circuit. The minimum requirement (to VE 0550) is 2,000 V. Screw terminals secure the inputside connection to the mains. The singlephase devices are rated for a nominal voltage of 230 ± 15 V, or 400 V ± 15 V, 50/60 Hz, the 3phase devices for 3 x 400 V ± 5 %. The secondary C voltage from the transformer is conducted to a bridge rectifier where it is rectified. The pulsating C voltage is then fed from the rectifier and filtered to a low residual ripple by means of an electrolytic capacitor. This C voltage is then fed to the output terminal. These are designed as pluggable screw terminals. A varistor is integrated in the output circuitry to attenuate voltage peaks. The operating status is indicated by means of a green LE via the output circuit. evices with 600 W and higher are equipped with a fan. Singlephase unregulated power supplies Threephase unregulated power supplies /2015
3 . Overview Wellbalanced spectrum for optimum economy The output currents of these practical products are defined by way of two ambient temperatures. Size selection is based on the maximum effectiveness of the components. Adapted to standard voltages in accordance with EC 38 y choosing the appropriate terminals, the ± 15 V tapping capability allows the singlephase devices to be connected to six different nominal AC voltages: 215, 230, 245, 385, 400, 415 V. The ± 5 % tapping capability allows the 3phase devices to be connected to three different nominal voltages: 380, 400, 415 V. Reliable shortcircuit and overload protection ntegrated on the secondary side in device sizes up to CP NT 192 W, the FKS fuse protects against overloads and shortcircuits. For the devices CP NT 264 W and CP NT 432 W, this protection is achieved by means of a thermostatic switch built into the transformer. lock diagram for singlephase devices CP NT 15 V 0 V 15 V 230 V 400 V lock diagram for 3phase devices CP NT3 250 / 400 / 500 W lock diagram for 3phase devices CP NT3 600 / 750 / W 24V C 5% 400 V 5% 5% 400 V 5% 5% 400 V 5% 3x = V C Easy mounting Keyhole assembly simplifies mounting and saves time. A snapon fixing attachment for 35 N rails is available as an accessory for singlephase devices up to 144 W. Simply plugged into the device and secured with two screws, it ensures easiest possible mounting! 5% 400 V 5% 5% 400 V 5% 5% 400 V 5% 3x 130 = M 24V C 0 V Fail Transformers, vacuumimpregnated, painted black No huing Moisture cannot ingress into the windings Windings mechanically secured mproved heat dissipation from the windings Good heat dissipation singlephase 3phase /2015.3
4 .. compactpower compactpower singlephase CP NT 36 CP NT 72 15V 15V 24VC V 15V 24VC voltage current frequency Noload input current Ext. ackup fuse voltage current at 40 C current at 55 C power nsulation coordination (EN 50178) nsulation strength nsulation class egree of efficiency at max. load Mounting position, installation notice nstallation advice 0.35 A/ 0.2 A 0.1 A / 0.06 A 0.63 A / A timelag 1.5 A 1 A 36 W 3 A timelag flat cablelug fuse P C...55 C 20 C...80 C 80% Arbitrary, horizontally, on terminal rail TS 35 irect mounting, TS 35 with clipon plate 1.5 kg N EN 60950, N EN , 6, 72/23/EWG EN /2, A/ 0.32 A 0.13 A / 0.08 A 0.1 A / 0.63 A timelag 3 A 2.5 A 72 W 7.5 A timelag flat cablelug fuse P C...55 C 20 C...80 C 83% Arbitrary, horizontally, on terminal rail TS 35 irect mounting, TS 35 with clipon plate 2.1 kg N EN 60950, N EN , 6, 72/23/EWG EN /2, 3 imensions epth x width x height 68 / 78 / / 78 / / 84 / / 84 / 125 CP NT 36W 24V 1.5A CP NT 72W 24V 3A Clipin plate for TS35: Clipin plate for TS35: /2015
5 .. compactpower compactpower singlephase CP NT 144 CP NT V 15V 24VC V 15V 24VC voltage current frequency Noload input current Ext. ackup fuse voltage current at 40 C current at 55 C power nsulation coordination (EN 50178) nsulation strength nsulation class egree of efficiency at max. load Mounting position, installation notice nstallation advice 0.95 A/ 0.55 A 0.33 A / 0.19 A 1.6 A / 1.0 A timelag 6 A 5 A 144 W 10 A timelag flat cablelug fuse P C...55 C 20 C...80 C 88% Arbitrary, horizontally, on terminal rail TS 35 irect mounting, TS 35 with clipon plate 3.1 kg N EN 60950, N EN , 6, 72/23/EWG EN /2, A/ 0.7 A 0.3 A / 0.16 A 2.0 A / 1.25 A timelag 8 A 7 A 192 W 15 A timelag flat cablelug fuse P C...55 C 20 C...80 C 90% irect mounting 4.3 kg N EN 60950, N EN , 6, 72/23/EWG EN /2, 3 imensions epth x width x height 92 / 96 / / 96 / / 105 / / 105 / 145 CP NT 144W 24V 6A CP NT 192W 24V 8A Clipin plate for TS 35: /2015.5
6 .. compactpower compactpower singlephase CP NT 264 CP NT V 15V 24VC V 15V 24VC voltage current frequency Noload input current Ext. ackup fuse voltage current at 40 C current at 55 C power nsulation coordination (EN 50178) nsulation strength nsulation class egree of efficiency at max. load nstallation advice 1.8 A/ 1 A 0.5 A / 0.28 A 3.15 A / 1.6 A timelag 11 A 10 A 264 W Thermostatic switch P C...55 C 20 C...80 C 93% irect mounting 6.1 kg N EN 60950, N EN , 6, 72/23/EWG EN /2, A/ 1.3 A 0.54 A / 0.31 A 4.0 A / 2.0 A timelag 18 A 15 A 432 W Thermostatic switch P C...55 C 20 C...80 C 95% irect mounting 9.1 kg N EN 60950, N EN , 6, 72/23/EWG EN /2, 3 imensions epth x width x height 113 / 120 / / 120 / / 135 / / 135 / 185 CP NT 264W 24V 11A CP NT 432W 24V 18A /2015
7 compactpower compactpower 3phase CP NT3 250 CP NT % 5% 5% 5% % 5% 3x = VC 40 5% 5% 5% 5% % 5% 3x = VC voltage current frequency Noload input current fuse Ext. ackup fuse voltage current at 40 C / 60 C power nsulation coordination (EN 50178) nsulation strength nsulation class egree of efficiency at max. load nstallation advice Fan signal 0.5 A 0.1 A 3 x 1.0 A timelag 11 A / 10 A 250 W External 10 A timelag P C...60 C 20 C...80 C 76% irect mounting No integrated fan 4.7 kg N EN 60950, N EN , 6, 72/23/EWG EN /2, 3 ccsaus; CE 0.75 A 0.11 A 3 x 1.2 A timelag 18 A / 16 A 400 W External 16 / 18 A sloblo P C...60 C 20 C...80 C 77% irect mounting No integrated fan 6.9 kg N EN 60950, N EN , 6, 72/23/EWG EN /2, 3 ccsaus; CE imensions epth x width x height 2.5 / 0.5 / / 0.5 / / 84 / / 84 / / 0.5 / / 0.5 / / 88 / / 88 / 213 CP NT3 250W 24V 10A CP NT3 400W 24V 15A /2015.7
8 compactpower compactpower 3phase CP NT3 500 CP NT % 5% 5% 5% % 5% 3x = VC 40 5% 5% 5% 5% % 5% 3x = VC M Fail voltage current frequency Noload input current fuse Ext. ackup fuse voltage current at 40 C / 60 C power nsulation coordination (EN 50178) nsulation strength nsulation class egree of efficiency at max. load nstallation advice Fan signal 0.9 A 0.13 A 3 x 1.6 A timelag 22 A / 20 A 500 W External 20 / 22 A sloblo P C...60 C 20 C...80 C 78% irect mounting No integrated fan 10 kg N EN 60950, N EN , 6, 72/23/EWG EN /2, 3 ccsaus; 1.2 A 0.15 A 3 x 2 A timelag 26 A / 25 A 600 W External 25 / 26 A sloblo P C...60 C 20 C...80 C 78% irect mounting Open collector <30 V/ <5 ma during interference 11 kg N EN 60950, N EN , 6, 72/23/EWG EN /2, 3 ccsaus; CE imensions epth x width x height 2.5 / 0.5 / / 0.5 / / 108 / / 108 / / 0.5 / / 0.5 / / 108 / / 108 / 212 CP NT3 500W 24V 20A CP NT3 600W 24V 25A /2015
9 compactpower compactpower 3phase CP NT3 750 CP NT % 5% 5% 5% % 5% 3x = VC M Fail 40 5% 5% 5% 5% % 5% 3x = VC M Fail voltage current frequency Noload input current fuse Ext. ackup fuse voltage current at 40 C / 60 C power nsulation coordination (EN 50178) nsulation strength nsulation class egree of efficiency at max. load nstallation advice Fan signal 1.4 A 0.16 A 3 x 2.5 A timelag 32 A / 30 A 750 W External 30 / 32 A sloblo P C...60 C 20 C...80 C 77% irect mounting Open collector <30 V/ <5 ma during interference 14 kg N EN 60950, N EN , 6, 72/23/EWG EN /2, 3 ccsaus; CE 1.8 A 0.14 A 3 x 3.15 A timelag 42 A / 40 A 1000 W External 40 / 42 A sloblo P C...60 C 20 C...80 C 77% irect mounting Open collector <30 V/ <5 ma during interference 18 kg N EN 60950, N EN , 6, 72/23/EWG EN /2, 3 ccsaus; CE imensions epth x width x height 2.5 / 0.5 / / 0.5 / / 121 / / 121 / / 0.5 / / 0.5 / / 122 / / 122 / 275 CP NT3 750W 24V 30A CP NT3 1000W 24V 40A /2015.9
10 /2015
For Immediate Delivery call KMParts.com at (866)
Contents 9/1 Page Description SN4 switched-mode power supply units 9/2 GW4 power supply units 9/3 GD4 power supply units 9/4 Basic Units, Accessories 9/5 Technical data 9/6 Dimensions 9/12 9/2 Description
More informationSM2000 TECHNICAL DESCRIPTION
SM2000 TECHNICAL DESCRIPTION 1 GENERAL DESCRIPTION The SM2000 module is a high frequency switch mode rectifier. It converts the single phase AC line voltage into an isolated DC voltage. It can be used
More informationAN003. Basic Terms Used for DC Power Supplies. Elaborated by: Marco Geri (R&D Manager - NEXTYS SA.)
AN003 Elaborated by: Marco Geri (R&D Manager - NEXTYS SA.) Rev.1.0 Page 1/5 1 Introduction DC (Direct Current) power supplies are used in various applications related to automation, telecom, industry,
More informationPower Supplies. 11/2 Introduction. 4AV Non-Stabilized. Power Supplies
Siemens AG 009 Power Supplies / Introduction AV Non-Stabilized Power Supplies Filtered for Supply of Electronic Controls General data / - Overview / - Design / - Function / - Technical specifications AV,
More informationTRIO-PS/1AC/24DC/ 5. Extract from the online catalog. Order No.:
Extract from the online catalog TRIO-PS/1AC/24DC/ 5 Order No.: 2866310 DIN rail power supply unit, primary-switched mode, 1-phase, output: 24 V DC / 5 A Commercial data EAN 4046356046640 Pack 1 pcs. Customs
More informationInstallation and Operational Instructions for ROBA -switch Type 017._00.2
Manufacturer s Declaration This product is intended for installation in a machine or system, based on the machine directive 2006/42/EC. It is forbidden to start use of the product until the machine or
More informationInstallation and Operational Instructions for ROBA -switch Type 017._00.2
OBA -switch Type 017._00.2 Guidelines on the Declaration of Conformity A conformity evaluation has been carried out for the product in terms of the EC Low Voltage Directive 2014/35/ EC and the EMC Directive
More informationDSSIU-6-1U. Dedicated 6-channel system interface unit for ultra-stable, high precision fluxgate technology DS series current transducers.
DSSIU-6-1U Dedicated 6-channel system interface unit for ultra-stable, high precision fluxgate technology DS series current transducers. Powers up to 6 x DS50 to DS2000 at the same time. Supports calibration
More informationPS16 SERIES. Features. Multiple Primary Windings: Either 120 VAC or 240 VAC, 50/60 Hz Operation 30 VDC, 36 VDC or 40 VDC Secondary Output Winding Taps
Description The PS unregulated power supplies have been designed to complement ADVANCED Motion Controls servo drives. Model PS is mounted on a base plate for multi-axis applications (mounting space provided
More information10/2 Product overview. 10/3 4AC3 0, 4AC3 1 bell transformers. 10/5 4AC AC3 6 transformers for permanent loads. 10/8 4AC2 4 power supply units
BETA Switching Transformers, Bells and Socket Outlets /2 Product overview /3 4AC3 0, 4AC3 1 bell transformers /5 4AC3 4... 4AC3 transformers for permanent loads /8 4AC2 4 power supply units / 7LQ2 2 bells
More informationUNO-PS/1AC/24DC/150W. Primary-switched power supply unit. Data sheet. 1 Description
Primary-switched power supply unit Data sheet 106261_en_02 PHOEIX COTACT 2015-05-13 1 Description The power supply makes a worldwide impression thanks to maximum energy efficiency. ow idling losses (o
More informationInstallation and Operational Instructions for ROBA -multiswitch Type 019._00.2
Guidelines on the Declaration of Conformity A conformity evaluation has been carried out for the product in terms of the EU Low Voltage Directive 2014/35/ EU and the Electromagnetic Compatibility (EMC)
More informationSwitching power supplies CP range, Linear power supplies CP-L range. Content
CP range, Linear power supplies CP-L range Content Switching power supplies, primary switch mode, CP range Benefits and advantages... 136 Approvals... 137 Ordering details... 138 Technical data... 11 Dimensional
More informationwenlok.com.mx Switched-mode and uninterruptible power supplies, and electronic fuses Let s connect. Power supply Catalogue 2015/2016
Switched-mode and uninterruptible power supplies, and electronic fuses Catalogue 2015/2016 Let s connect. Power supply Switch-Mode and Uninterruptible Power Supplies, Electronic Fuses Catalogue 4.3 Switch-Mode
More informationXIOC technology and networking modules
/ XIO XIO digitale and analog input/output modules XIO technology and networking modules XIO the compact I/O and much more XIO are local expansion modules for direct connection to all Xontrol controllers.
More informationPower Supplies. SCL Series. Features. Related Products. Applications
SDN Series The SDN family of DIN Rail power supplies have industry leading performance with a true industrial grade design and high quality that meets difficult industrial environmental conditions including
More informationSINEAX V604s Programmable multifunctional transmitter
SINAX V60s for direct currents, direct voltages, temperature sensors, teletransmitters or potentiometers SINAX V60s is a multifunctional transmitter for tophat rail assembly with the following main characteristics:
More informationDSSIU-6-1U-V. Features VOM:
Fully configurable dedicated 1U high 6-channel system interface unit for ultra-stable, high precision fluxgate technology DS series current transducers. Powers up to 6 x DS50 to DS2000 at the same time.
More informationQUINT-PS/ 3AC/24DC/10
Primary-switched power supply with SFB technology, 3 AC, output current 10 A INTERFACE Data sheet 103131_en_01 1 Description PHOENIX CONTACT - 09/2009 Features QUINT POWER power supply units Maximum system
More informationSINEAX V 624 Programmable Temperature Transmitter for RTD and TC inputs
SINEAX V 6 for rail mounting in housing P/7 or P/7 St 00 II () GD Application SINEAX V 6 (Figs. and ) is designed for measuring temperature in combination with thermocouples or resistance thermometers.
More informationCourtesy of CMA/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800)
Primary switched-mode power supply units In standard machine production, the requirements for a power supply unit are mostly specified in advance. Here, the TRIO POWER power supply units are suitable which
More informationPower supply CP-D 24/1.3
2CDC 271 027 F0t07 a OUTPUT ++/ : terminals output Features Rated output voltage 24 V DC Output voltage adjustable via front face potentiometer OUTPUT Adjust Rated output current 1.3 A Rated output power
More informationMotor Controllers 3-Phase Analog Power Controller Types RSC-AAM60/RSO...
otor Controllers 3-Phase nalog Controller Types RSC-60/RSO... Control and output modules for analogue control of 3-phase induction motors or heaters Rated operational current: 3 x, 25, 50, 90, 1 Crms Rated
More informationAnalog signal converters CC-E I/I
2CC 281 001 F0b06 Features Loop-powered I/I isolator without external power supply for analog current signals of 0-20 ma and 4-20 ma Electrical isolation between input and output Very low internal voltage
More informationQUINT-PS/ 1AC/24DC/20
Primary-switched power supply with SFB technology, 1 AC, output current 20 A INTERFACE Data sheet 103129_en_04 1 Description PHOENIX CONTACT - 02/2010 Features QUINT POWER power supply units Maximum system
More informationAdvantages. Applications
3 s KH 250 General Data Rated input voltage 2 Vac Rated output voltage 2 Vac Rated power 250 VA Ambient temperature +40 C Degree of protection IP 40 Advantages Compensation for mains voltage fluctuations
More informationType CP-S, CP-C & CP-A Switch mode
Switch mode power CP-S, CP-C & CP-A Switch mode Characteristics CP-S and CP-C range Output current 5 A, 10 A and 20 A Integrated power reserve of up to 50 % 5 A and 10 A devices with pluggable connecting
More informationTechnical Information Barrier RB223
TI00132R/09/EN/13.14 71275790 Products Solutions Services Technical Information Barrier RB223 One or two-channel barrier Loop-powered barrier for the safe separation of 4 to 20 ma standard signal circuits
More informationPower supply CP-D 24/4.2 Primary switch mode power supply
Data sheet Power supply CP-D 24/4.2 Primary switch mode power supply The CP-D range of modular power supply units in MDRC design (modular DIN rail components) is ideally suited for installation in distribution
More informationPower supply CP-D 12/2.1
2CDC 271 025 F0t07 a OUTPUT ++/ : terminals output Features Rated output voltage 12 V DC Output voltage adjustable via front face potentiometer OUTPUT Adjust Rated output current 2.1 A Rated output power
More informationENERALE. Electronic Products
CG ATALOGO ENERAL CGATALOGUE ENERALE Electronic Products 106 USE OF POWER SUPPLY UNITS SERIES CS, CL, AR GENERAL NOTES LENGTH OF CONDUCTOR PEELING: 9 mm, model with fixed terminals; 6 mm, model with pluggable
More informationINPUT: 110/220VAC. Parallel Input Series Input Parallel Output Series Output (W/CT)
Linear power supply design: To make a simple linear power supply, use a transformer to step down the 120VAC to a lower voltage. Next, send the low voltage AC through a rectifier to make it DC and use a
More informationCP-T range Benefits and advantages
Benefits and advantages Characteristics Rated output voltages V, V DC Output voltage adjustable via front-face rotary potentiometer OUTPUT Adjust Rated output currents 5 A, 10 A, A, A Rated output powers
More informationTRIO-PS-2G/1AC/24DC/5
TRIOPS2G/1AC/24DC/5 Power supply unit Data sheet 105900_en_01 PHOENIX CONTACT 20150831 1 Description TRIO POWER power supplies with standard functionality The power supplies of the TRIO POWER family convince
More informationRailbus isolator. Railbus isolator 8922-RB-IS
Railbus isolator Railbus isolator 8922-RB-IS provides galvanic isolation between Railbus sections prevents fault-voltage invasions protects IS field wiring modules See also System Specification Dimensions
More informationSINEAX I 503 / SINEAX U 504 Transducer for AC current or AC voltage
Application The transducers SINEAX I 503/U 504 (Figs. 1 and 2) are designed to convert a sinusoidal AC current or voltage into a load independent DC signal proportional to the measured value. This output
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer IN 1000-S I P N = 1000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Closed loop (compensated)
More informationLDW25-24 is a single or two phase AC or DC input DIN Rail Switching Power Supply.
LDW25-24 is a single or two phase AC or DC input DIN Rail Switching Power Supply. Its compact size, high efficiency, excellent reliability together with easy installation due to pluggable connectors makes
More informationLDC240 Series is a single phase, ultra compact DIN Rail Switching Power Supply with active PFC, ideal for many applications.
LDC240 Series is a single phase, ultra compact DIN Rail Switching Power Supply with active PFC, ideal for many applications. Its compact size, high efficiency, excellent reliability together with easy
More informationLDC480 Series is a single phase, extremely compact Power Supply with active PFC specially designed for space sensitive and demanding applications.
LDC480 Series is a single phase, extremely compact Power Supply with active PFC specially designed for space sensitive and demanding applications. Its compact size, high efficiency, excellent reliability
More informationPower supply CP-E 24/0.75
2CDC 271 016 F0t06 a OUTPUT L+, L : terminals output b INPUT L, N, PE: terminals input c LOW: red LED output voltage too low d OK: green LED output voltage OK e OUTPUT Adjust: rotary potentiometer output
More informationInstallation- / Monitoring technique
Installation- / Monitoring technique ifferential current monitor IP 5883, Type B for AC and C systems varimeter 0249633 IP 5883 N 5018/035 N 5018/030 According to IEC/EN 62 020, VE 0663 To detect earth
More informationSeries P. Applications
Ratings 25 800 VA Voltage Primary 230 / 400 / 460 V range Secondary 6 / 12 V 12 / 24 V 24 / 48 V 115 / 230 V Voltage selection by means of metal connection bridges, offering the full rated power at any
More informationInstallation and Operating Instructions for Phase Demodulator Type _.2
Guidelines on the Declaration of Conformity A conformity evaluation has been carried out for the product in terms of the EU Low Voltage Directive 2014/35/EU and the Electromagnetic Compatibility (EMC)
More informationSRA 2250/6 RESISTOR ARS-01 RESISTOR AUTOMATICS
ELECTRICAL ENGINEERING DIVISION Distribution Network Department SRA 2250/6 RESISTOR ARS-01 RESISTOR AUTOMATICS ELA T150.2 en SRA 2250/6 Resistor specification The SRA 2250/6 Resistor is intended to increase
More informationQUINT-PS/ 3AC/24DC/40
Primary-switched power supply unit with SFB technology, 3 AC, output current 40 A INTERFACE Data sheet 103133_en_00 1 Description PHOENIX CONTACT - 07/2009 Features QUINT POWER power supply units Maximum
More informationPower supply CP-E 24/2.5
2CDC 271 015 F0t06 a OUTPUT L+, L : terminals output b DC OK: terminal signalling output c INPUT L, N, PE: terminals input d OUTPUT OK: green LED output voltage OK e OUTPUT Adjust: potentiometer adjustment
More informationPOWER SUPPLY MODEL XP-720. Instruction Manual ELENCO
POWER SUPPLY MODEL XP-720 Instruction Manual ELENCO Copyright 2016, 1997 by ELENCO Electronics, Inc. All rights reserved. Revised 2016 REV-H 753270 No part of this book shall be reproduced by any means;
More informationAnalog amplifier RA. RE Edition: Replaces:
Analog amplifier RA RE 950 Edition: 08.05 Replaces: 0.006 For control of simple functions of electrohydraulic components Two power outputs (PWM) and one switching output Each output has a separately adjustable
More informationTechnical manual. Microstep driver SMC11. NANOTEC ELECTRONIC GmbH & Co. KG Gewerbestraße 11 D Landsham near Munich, Germany
Technical manual Microstep driver NANOTEC ELECTRONIC GmbH & Co. KG Gewerbestraße 11 D-85652 Landsham near Munich, Germany Tel. +49 (0)89-900 686-0 Fax +49 (0)89-900 686-50 info@nanotec.de Editorial Editorial
More informationPower supply CP-E 24/20.0
2CDC 271 027 F0008 a OUTPUT L+, L+, L, L-: terminals output b INPUT L, N, PE: terminals input c 13-14: terminals - signalling contact d OUTPUT OK: green LED output voltage OK e OUTPUT LOW: red LED output
More informationPrimary switch mode power supplies Product group picture
Primary switch mode power supplies Product group picture /1 ABB Catalog Electronic Products and Relays 2015 2CDC 110 004 C0210 Primary switch mode power supplies Table of contents Primary switch mode power
More informationNo-wear isolation of potentials in terminal block design
TERMOPTO Overview No-wear isolation of potentials in terminal block design Space saving solid-state relay with PUSH IN connection technology The TERMOPTO opto modules are characterised by a particularly
More informationQUINT-PS-24DC/24DC/10
QUINT-PS-24/24/10 QUINT - converter, primary switched mode, input: 24 V, output: 24 V /10 A INTERFACE Data Sheet PHOENIX CONTACT - 02/2006 Description The QUINT - converter 24 V/10 A converts the voltage
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer IN 1000-S N = 1000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Closed loop (compensated)
More informationRISH Ducer TV 808, 2 channels Isolating amplifier unipolar / bipolar
Fig. 1. Isolating amplifier RISH Ducer TV 808 in housing S 17 clipped onto a top - hat rail or screw hole mounting brackets pulled out. Features and Benefits Electric Isolation between input, and power
More informationTechnical Bulletin Switch Mode PS Principles Page 1 of 5
Technical Bulletin Switch Mode PS Principles Page 1 of 5 Switch Mode PS Principles By G8MNY (Updated Dec 06) (8 Bit ASCII Graphics use code page 437 or 850) There are 2 types, they work slightly differently
More informationCP-T range Product group picture
Product group picture /1 ABB Catalog Electronic Products and Relays 1/1 2CDC 110 00 C09 Table of contents CP-T range Product group picture /1 Table of contents /2 Benefits and advantages / Ordering details
More informationProduct Data Sheet RG160-28/18N/2TDPU-331
RG160-28/18N/2TDPU-331 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating
More informationPhase and neutral overcurrent protection
Phase and neutral overcurrent protection Page 1 ssued June 1999 Changed since July 1998 Data subject to change without notice (SE970165) Features Two-phase or three-phase time-overcurrent and earth fault
More informationaudionet AMP 1 V2 User s Manual Stereo - Amplifier
audionet AMP 1 V2 Stereo - Amplifier User s Manual 1 2 Contents 1 Preface... 4 1.1 Included... 5 1.2 Transport... 5 2 Overview control elements... 6 2.1 Front panel... 6 3 Overview connections... 7 3.1
More informationActive Transmitter Combiner 8:1 AC 3200-II. Instruction manual
Active Transmitter Combiner 8:1 AC 3200-II Instruction manual Contents Contents Important safety instructions... 2 The AC 3200-II active transmitter combiner 8:1... 4 Delivery includes... 4 Connection
More information3.6. Control Relays and Timers D A M D 2. Contents. Product Overview. Catalog Number Selection. Solid-State Relays
.6 Control Relays and Timers Product Overview Catalog Number Selection D9, D96 and D99 Series Description D9 = Hockey puck D96 = Compact D99 = DIN rail Contents D 9 2 5 A M D 2 Output Voltage 1 = 2 60
More informationProduct Data Sheet RER220-43/18/2TDMO
RER220-43/18/2TDMO INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating Data...
More informationPHOENIX CONTACT - 05/2008. DANGER OF EXPLOSION! Remove an item only when it is not connected to power or if it is located in the non-explosive area.
Primary-switched power supply with SFB technology, 1 AC, output current 20 A INTERFACE Data Sheet 103129_en_01 PHOENIX CONTACT - 05/2008 1 Description QUINT POWER power supply units highest system availability
More informationX Series Data Sheet 375, 500 Watt AC-DC and DC-DC DIN-Rail Converters
Features RoHS lead-free-solder and lead-solder-exempted products are available Rugged 5 mm DIN-rail snap-fit design Class I equipment Universal AC-input with single stage conversion AC to DC or DC input
More informationSolid State Relays Industrial, 1-Phase ZS (IO) w. LED and Built-in Varistor Types RM 23, RM 40, RM 48, RM 60
Solid State Relays Industrial, 1-Phase ZS (IO) w. LED and Built-in Varistor Types RM 23, RM 40, RM 48, RM 60 Zero switching (RM1A) or instant-on switching (RM1B) AC Solid State Relay Direct copper bonding
More informationPHOENIX CONTACT - 06/2008. Features. DANGER OF EXPLOSION! Only remove equipment when it is disconnected and not in the potentially explosive area.
Primary-switched power supply with SFB technology, 1 AC, output current 20 A INTERFACE Data Sheet 103383_en_00 1 Description PHOENIX CONTACT - 06/2008 Features QUINT POWER power supply units highest system
More informationCCH400 & CCH600 Series
CCH4 & CCH6 Series 4 W & 6 W - Baseplate Cooled Compact 8.4 (214 mm) x 4 (12 mm) x 1.69 (43 mm) Package High Efficiency up to 9% -4 C to +85 C Baseplate Operating Temperature No Fan, Quiet Operation MIL-STD-461
More informationINTEGRATED CIRCUITS. AN120 An overview of switched-mode power supplies Dec
INTEGRATED CIRCUITS An overview of switched-mode power supplies 1988 Dec Conceptually, three basic approaches exist for obtaining regulated DC voltage from an AC power source. These are: Shunt regulation
More informationMBS AG. KBR 18 Split-core current transformer. Further information about our new split-core current transformer KBR 18: Dimensions:
KBR 18 Split-core current transformer Dimensions: Round conductor: 18 mm Transformer width: 41.6 mm Transformer height: 64.5 mm Transformer depth incl. fixing clasps: 67.3 mm General technical specifications:
More informationPower supply CP-E 24/2.5
2CDC 271 015 F0t06 a OUTPUT L+, L : terminals output b DC OK: terminal signalling output c INPUT L, N, PE: terminals input d OUTPUT OK: green LED output voltage OK e OUTPUT Adjust: potentiometer adjustment
More informationPower supply CP-E 12/10.0 Primary switch mode power supply Data sheet
2CDC 271 024 F0008 OUTPUT L+, L+, L-, L-: terminals - output INPUT L, N, PE: terminals - input OUTPUT OK: green LED - output voltage OK OUTPUT LOW: red LED - output voltage too low OUTPUT Adjust: potentiometer
More informationTap Changer Analyzer & Winding Ohmmeter RMO60TD
Tap Changer Analyzer & Winding Ohmmeter RMO60TD Test current 5 ma 60 A DC Rapid automatic demagnetization AC Current monitoring channel Lightweight 13 kg Measuring range 0,1-2 k Two voltage sense channels
More informationDifferential pressure sensors
1 912 1912P02 QBM64/ 1912P01 QBM63/ Differential pressure sensors for air and non-aggressive gases, with a diaphragm sensing element QBM63/ QBM64/ With choice of pressure-linear or extracting-the-root
More informationCurrent / residual current and voltage transformers. Current / residual current and voltage transformers
Current / residual current and voltage transformers Current / residual current and voltage transformers 1 Overview Current transformer overview DIN rail current transformer with fuse Current transformer...
More informationType: DILM80(110V50HZ,120V60HZ) Article No.: Sales text Contactor,37kW/400V,AC operated. Ordering information
Type: DILM80(110V50HZ,120V60HZ) Article No.: 239399 Sales text Contactor,37kW/400V,AC operated Ordering information Connection technique Description Description Rated operational current AC 3 380 V 400
More informationNT & NQ CLASS II TRANSFORMERS FOR SIGNALLING SYSTEMS. A Balfour Beatty and Alstom Company
NT & NQ CLASS II TRANSFORMERS FOR SIGNALLING SYSTEMS A Balfour Beatty and Alstom Company NT Transformers CLASS II DOUBLE INSULATED HYBRID TRANSFORMERS / LOW POWER-T/J COMBINED UNITS FOR RELAY AND SSI SIGNALLING
More informationType: DILM95(230V50HZ,240V60HZ) Article No.: Sales text Contactor,45kW/400V,AC operated. Ordering information
Type: DILM95(230V50HZ,240V60HZ) Article No.: 239480 Sales text Contactor,45kW/400V,AC operated Ordering information Connection technique Description Description Rated operational current AC 3 380 V 400
More informationOperating Instruction
Level and Pressure Operating Instruction VEGASEL 643 6 5 + + 3 5 + + max. min. on VEGASEL 643 5 6 7 8 9 10 11 12 13 14 in out Contents Contents Safety information... 2 1 Product description 1.1 Function
More informationâ itemp Pt100 TMT127 Technical information Pt100 transmitter for DIN rail mounting for high accuracy temperature monitoring
Technical information itemp Pt100 TMT127 Pt100 transmitter for DIN rail mounting for high accuracy temperature monitoring Application Temperature transmitter with fixed measuring range for converting a
More informationTriplett 3444A Power Supply Modification Notes
Triplett 3444A Power Supply Modification Notes The Triplett 3444A is a superb Tube Test/Analyzer. Mutual Conductance is measured by inserting a small known AC signal on the Grid, and measuring the AC Plate
More informationCOMPACT LED DRIVERS. ComfortLine Selectable Current (LEDset) ComfortLine SELECTABLE CURRENT LEDset ,
COMPACT LED DRIVERS ComfortLine SELECTABLE CURRENT LEDset 186650, 186664 Typical Applications Built-in in compact luminaires for Shop lighting Downlights ComfortLine with selectable current SELECTABLE
More informationMINI-PS AC/24DC/1.3
Power supply unit INTERFACE Data sheet 102894_en_03 1 Description PHOENIX CONTACT 2015-11-17 Features MINI POWER power supplies for MCR technology In measurement and control technology (MCR), modular electronics
More informationOptions & Accessories
75 mm (2.95-inch) BLDC Motor with Integrated Sensorless Digital Drive Allied Motion s Gen III EnduraMax 75s series motors are 75 mm (2.95 in) diameter brushless DC motors that incorporate integrated drive
More informationManual. MOVITRAC LTE-B+/LTP-B Accessories Braking Resistors, Filters, Chokes, Shielding * _0618*
rive Technology \ rive Automation \ System Integration \ Services *23540052_0618* Manual MOVITRAC LTE-B+/LTP-B Accessories Braking Resistors, Filters, Chokes, Shielding Edition 06/2018 23540052/EN SEW-EURORIVE
More informationHigh-Voltage Isolation Amplifiers / Shunt Isolators. VariTrans P 29000
High-Voltage Isolation Amplifiers / Shunt Isolators VariTrans P 29000 Compact high-voltage isolators with safe galvanic isolation, VariPower broad-range power supply and genuine calibrated range selection.
More informationFINAL - ET 60 - Electrician Theory Examination Marking Schedule
FINAL - ET 60 - Electrician Theory Examination Marking Schedule Notes:1. means that the preceding statement/answer earns 1 mark. 2. This schedule sets out the accepted answers to the examination questions.
More informationMOVING-IRON METERS EA16, EB16, EA17, EA19, EA12 TYPES
MOVING-IRON METERS EA16, EB16, EA17, EA19, EA12 TYPES AMMETERS and VOLTMETERS EA12 EA19 EA17 EA16 EB16 EA16, EB16, EA17, EA19 and EA12 moving-iron meters are intended for measuring AC voltage or AC current.
More informationQUINT-PS AC/24DC/40
Power supply unit INTERFACE Data sheet 102315_en_02 1 Description PHOENIX CONTACT 2010-04-23 Features QUINT POWER power supply units for plant and special engineering reliably start heavy loads with high
More informationFreeSpace ZA 250-LZ / 190-HZ zone amplifier TECHNICAL DATA SHEET. Key Features. Product Overview. Product Information.
Product Overview Zone amplifier designed to serve as a standalone amplification system or expansion sound system that utilizes front-end signal processing from products such as FreeSpace IZA 250-LZ / IZA
More informationP RODUCT C ATALOGUE 1/2002
S a f e t y R e l a y s S e r i e s U E 1 0-4 8 P RODUCT C ATALOGUE 1/2002 For technical details please unfold 2 SICK Industrial Safety Systems Germany All rights reserved 8 009 607/30-03-02 UE 10 UE 48
More informationAnalogue temperature transmitter Model T91.10, head mounting version DIN form B Model T91.20, head mounting version form J
Electrical temperature measurement Analogue temperature transmitter Model T91.10, head mounting version DIN form B Model T91.20, head mounting version form J WIKA data sheet TE 91.01 for further approvals
More informationDC Power Supply Design
Sopczynski 1 John Sopczynski EE 310 Section 4 DC Power Supply Design Introduction The goal of this experiment was to design a DC power supply. Our team would be receiving 120 Vrms oscillating at 60 Hz
More information* Short-circuit detection at On pushbutton. Applications. Indication. S M6801_a S11 A3 S12 S21 S23 S22 S (+)
Safety technique Emergency stop module BO 5988 safemaster 0221562 Function diagram Pushbutton on Mains or emergencystop () K1 According to EC Directive for machines 98/37/EG According to IEC/E 60204-1
More informationUniversal signal transducer UKU
Universal signal transducer with fully isolated inputs and outputs Universal signal transducer Full isolation between the inputs and outputs Signals can be converted and linearised Adjustable signal level
More informationK Factor Power Transformers
Ashley-Edison AsiaElectricTransformers (UK) K Factor Power Transformers DTKF series Low Voltage Dry Type K Factor Power Transformers AET-DTKF-2004-01: Page 1 Asia Electric Transformers, Entrepreneur Business
More informationAC 3. Active Antenna Combiner. Instruction manual
AC 3 Active Antenna Combiner Instruction manual Contents Contents Important safety instructions... 2 The AC 3 active transmitter combiner... 4 Delivery includes... 4 Operating controls... 5 Block diagram...
More informationExtract from the online catalog
Please note that the data given here has been taken from the online catalog. For comprehensive information and data, please refer to the user documentation at http://www.download.phoenixcontact.com. The
More informationSINEAX / EURAX 2I1 Passive DC signal isolator
SINEAX / EURAX I without power supply 0 II () G resp. II () G Application The DC signal isolator SINEAX/EURAX I (Figs. and ) serve to isolate load-independent DC current signals. It suppressed noise voltages
More information