ENGINEERING TRIPOS PART II A ELECTRICAL AND INFORMATION ENGINEERING TEACHING LABORATORY EXPERIMENT 3B2-B DIGITAL INTEGRATED CIRCUITS

Size: px
Start display at page:

Download "ENGINEERING TRIPOS PART II A ELECTRICAL AND INFORMATION ENGINEERING TEACHING LABORATORY EXPERIMENT 3B2-B DIGITAL INTEGRATED CIRCUITS"

Transcription

1 ENGINEERING TRIPOS PART II A ELECTRICAL AND INFORMATION ENGINEERING TEACHING LABORATORY EXPERIMENT 3B2-B DIGITAL INTEGRATED CIRCUITS OBJECTIVES : 1. To interpret data sheets supplied by the manufacturers of digital integrated circuits and to use the data in a design exercise. 2. To make measurements on NAND gates from two different technologies to compare logic output levels, propagation delays and power consumption. 3. To investigate how the power-delay products for each of these technologies varies with switching frequency. 4. To gain experience in using oscilloscope probes with a 100 MHz oscilloscope to make accurate measurements down to a few nanoseconds. 5. To assemble and test a simple system using digital ICs. 6. To record the system waveforms. 1

2 Page deliberately left blank 2

3 PERFORMANCE AND APPLICATION OF DIGITAL INTEGRATED CIRCUITS 1. Introduction and aims. 2. Apparatus. 3. Procedures. 4. Performance measurements. 5. Applications. 1. Introduction Skill and experience are needed before an engineer can quickly decipher Manufacturers Data sheets for integrated circuits and use the information they contain to design an electronic system. As integrated circuits packages steadily increase in complexity the importance of this kind of experience becomes greater. Different technologies have been developed and manufacturing techniques are continually improving which has led to the present day situation where there are many different digital integrated circuit families from which to choose. The main factors affecting the designer s choice are speed of operation, power consumption, cost and the particular application. In this experiment logic gates from two different families are examined for speed (in terms of propagation delay) and power consumed at various switching rates to make a comparison in terms of a power-delay product. Other basic parameters are to be measured and compared with quantities in the published data sheets. A data sheet pack is issued for this experiment, which includes all the necessary information and pin connections for all the devices, which may be used. The second part of this experiment is to construct and test in a breadboard form either a pulse generator or a logic circuit to illustrate the operation of a traffic light sequence. Records of the relevant waveforms are to be made and included in your report. In addition to the two hours laboratory time a similar amount of time should be devoted to a written report, which will include some design and further reference to the data sheets. The integrated circuit types to be used are listed below: - (a) 74C00, 74LS00 (b) 74LS04 (c) 74LS13 (d) 74LS76 (e) 74LS123 (f) 74LS93 (g) 74LS86 Quad 2-input NAND gates Hex inverters Dual 4-input NAND gates with Schmitt inputs Dual J-K Flip-flops Dual retriggerable monostable multivibrators 4-bit binary counter Quad Exclusive-OR gates 3

4 2. Apparatus The apparatus available for this experiment includes a 100 MHz oscilloscope to display waveforms, a DMM for current and voltage measurements, a test box comprising of power supply and oscillators to provide the necessary test signals, a prototyping breadboard for the construction of test circuits and LEDs in red, green and yellow for use as diagnostic indicators. 2.1 The 100 MHz oscilloscope has a rise-time of 3.5 nanoseconds and for the measurements to be made it is most important that it is used with correctly adjusted x10 probes. The benefit of using probes is to reduce the loading of the oscilloscope input to a capacitance of 15 pf in parallel with a resistance of 10 Megohms, whilst maintaining the full oscilloscope bandwidth. If you are unsure of the techniques for displaying waveforms and making the necessary measurements then you are advised to consult your demonstrator. 2.2 The digital Multimeter (DDM) is used in current mode to measure the current consumed by the device or circuit under test at the sockets situated on the Test Box and may be used in voltage mode to measure logic levels. Remember for greater accuracy it is necessary to display as many digits as possible. 2.3 The Test Box contains a 5-volt power supply. Internal oscillators produce a low frequency square wave at 1 Hz and a high frequency clock at selected frequencies of 100kHz, 300kHz and 1 MHz. The test socket is wired as shown in Appendix A to accept 74C00 and 74LS00 NAND gates, which have identical pin connections. The four gates in each package are connected as inverters in series. The output of each gate is available at the monitor points G1, G2, G3 and G4, whilst the input to the first gate has a separate monitor point and is connected to the internal oscillator or to ground as determined by the switch. 2.4 A prototype breadboard is provided for the construction of test circuits. The arrangement of the connections beneath the matrix of sockets is as indicated in Fig. 1; note that top and bottom rows of the board are continuously linked and can act conveniently as supply rails. For connections use only SINGLE STRAND wire or component leads of less than 0.85 mm diameter. 2.5 An LED diagnostic probe suitable for TTL logic circuits is shown in Fig. 2. The current limiting resistor is essential to prevent damage to the LED. The additional diode limits the reverse bias of the LED to approximately 0.7 volts and so prevents the possibility of reverse voltage breakdown. This protection diode may be omitted for most circuit configurations such as the LED indicators in the traffic light sequence. 4

5 LED data: IF max = 50mA, VF = 2.1V at IF =12mA VR = 3V Cathode is indicated by a notch or flat on the LED body. 3 Procedures some general points to bear in mind 3.1 Digital circuits switch very rapidly. If the power supply is not adequately decoupled on the circuit board, then the self-inductance of the supply leads can lead to poor transient behavior. This will be seen as high frequency ringing on outputs and can cause spurious triggering of sequential circuits. A 10 or 100 nf capacitor connected across the supply lines close to the IC package should alleviate any such problems 3.2 Propagation delays are customarily assessed as the time elapsing between the input signal passing through a fixed voltage level, at which switching occurs, and the output passing through the same level. You should study the manufacturer s data to establish the value of this fixed voltage for each IC technology. 3.3 The usual technique for measuring rise and fall times is based on finding the 10% and 90% points of the transition being examined. It is relatively easy to obtain accurate measurements of the rise and fall times by following the instructions in the oscilloscope user manual. 3.4 Manufacturers quote in their data conditions under which any parameter is measured. For propagation delay measurements a recommended load is specified and this in general will relate to the loading, which would be imposed on an output by other logic inputs of the same IC family. In order to compare your results with the manufacturer s data remember that the oscilloscope probe when correctly adjusted will load any monitor point with a capacitance of approximately 15 pf. The resistance of the probe at 10 Megohms can be ignored. 5

6 3.5 It is important that in the scheduled laboratory time you make all the measurements and observations necessary for your write-up. If you have any problems, particularly difficulties with operating the oscilloscope do not hesitate to seek guidance from your demonstrator. Make sure you leave sufficient time to make a record of the waveforms for your chosen application. Most of the comparisons with data sheet values and all design can be done separately as part of your report and should not be regarded as time to be spent in the laboratory. 4 Performance measurements 74C00 and 74LS00 Quad 2-input NAND gates The type numbers above represent members of two different device technologies, namely CMOS and low-power Schottky TTL respectively. A prefix of two or more letters is used by semiconductor manufacturers to identify their products. A suffix usually refers to the type of packaging. In TTL technologies bipolar devices are switched in and out of saturation; in CMOS, p- and n- type MOSFETs are used in a push-pull arrangement. While the pin connections and logical functions of the 74C00 and 74LS00 are identical, their electrical characteristics differ in a number of important ways. There are several other technologies available to the designer, including further CMOS and TTL variants, and the emitter-coupled logic families. Although some of these are very widely used it is not possible to investigate all of these within the scope of this experiment. The aim of this section is to elucidate the main differences in the characteristics between the different gate types, and to compare their measured performance with the manufacturer s specifications. It will be seen from the data the CMOS gates consume only a very same amount of supply current when the outputs are in either the logic 0 or logic 1 states. This is because either the p-channel or n-channel MOSFETs are cut-off and only leakage current flows. Significant power is consumed only when switching occurs and this will depend on the loading, which is assumed to be entirely capacitive for other CMOS gate inputs, and will be directly proportional to the switching rate. The data for the bipolar technologies shows that power is taken when outputs are at either low or high. This because npn transistors capable of sinking or sourcing current are conducting in the corresponding logic states. When switching, further supply current is required to drive circuit capacitances and other TTL inputs, but this increase with switching frequency is relatively small compared with the quiescent current. 6

7 4.1 CMOS NAND gates Using the Test Box carry out measurements are follows: (i) Insert a 74C00 package in the test socket. This is a zero insertion force (ZIF) socket and the IC is retained and released by operating the attached lever. Connect the DMM set to measure current between the 4mm sockets marked 1 cc. (ii) Set the Test Box oscillator frequency to 100 khz and record the supply current (in micro-amps). Repeat at 300 khz, 1MHz and with the input grounded. (iii) With the test oscillator frequency at 1 MHz compare the input waveform with the waveform at the output of the first gate. Examine the output high-low and low-high transitions and obtain a value of the propagation time in each case. Propagation delay is measured at the typical switching level and this voltage is quoted in the manufacturer s data. (iv) Measure the propagation delay through all four gates in the package (i.e. from the INPUT to G4 output), and thus obtain an average figure for t phl and t plh. (v) Measure the low and high logic voltage levels. This can be achieved more accurately by grounding the input so that gate outputs G1 and G3 will be high and gate outputs G2 and G4 low. Values can then be read as DC voltages using the DMM. 4.2 Low Power Schottky TTL NAND gates Replace the 74C00 device with a 74LS00 Quad 2-input NAND gate and repeat the measurements as in 4.1(ii) to 4.1 (v). It will be necessary to use the milliamp scale for the supply currents and to check again for the quoted switching level from the manufacturer s data. Make sure that you have recorded all the necessary details for this measurement section then proceed to one of the applications in the next section. The write-up should contain on a single graph a plot of the power-delay product against frequency for both types of NAND gate. It should be possible to conclude over what frequency range CMOS has an advantage in the power-delay figure of merit over the low power Schottky. In comparing measured parameters with the manufacturer s data draw up tables and list where appropriate the minimum, typical and maximum values specified in the data against your recorded values. Comment on your findings. 7

8 5 Applications of Digital Integrated Circuits You are expected to construct ONE of the systems: EITHER OR (a) a Pulse Generator (b) a Traffic Light Controller In each case a basic circuit is provided and the prototype breadboard is to be used to assemble the chosen system. Care should be taken to keep interconnections as short as possible. The positioning of the oscilloscope earth lead in relation to the other circuit earths can also be critical when observing high speed switching waveforms. Use decoupling capacitors as recommended where necessary. A small stock of discrete components (R, C, etc) is available in the laboratory. Consult a demonstrator if you feel that you need components not already available on the bench. Also available are printers to record the output and prepulse waveforms for the pulse generator or the three traffic light controller outputs. A single printer output should show the relative timing of the waveforms. Ask a demonstrator to check your display settings before you attempt to record the waveforms. 5.(a) Pulse generator 5.1 Construct the simple pulse generator with the component values and digital integrated circuit types as shown in Fig. 3. It is intended that the Schmitt oscillator generates a basic pulse repetition frequency, the monostable multivibrator form a short duration prepluse and the final bistable circuit shape the output into a symmetrical square wave. The output of the Schmitt oscillator is not a symmetrical square wave although its frequency is determined by a single RC time constant. This is because TTL devices have significant output resistance for high level outputs and draw significant input current for low level inputs. The circuit can function over a very wide frequency range by changing the capacitance value but the choice of resistance value is limited to a narrow range around 330 ohms. 5.2 Make any modifications to the circuit to ensure the observed waveforms are as clean as possible then record the output and prepulse waveforms. Optionally you may like to include the Schmitt output waveform as part of the timing sequence. Some thought will be needed to arrive at the best method for triggering the display. 8

9 Make accurate measurements of: - (i) (ii) (iii) (iv) The frequency of the output square wave. The duration of the prepluse. The rise and fall times of the output square waves. The supply current. In your report compare your measurements with the quantities extracted from manufacturer s data wherever this is relevant. 5.3 As part of your report, design a pulse generator based on that shown in Fig. 3, and using the same three digital ICs to provide, in addition, a second square wave output. Using your experimental results or device data choose circuit component values to generate square wave outputs at 100 khz with the first square wave delayed by the prepulse by 500 ns. The second square wave output is to have variable delay relative to the original square wave output. Design for a minimum delay of 500 ns (so that both outputs can be coincident) and the maximum feasible delay. What do you expect this maximum delay to be? The NAND gate in the other half of the 74LS13 Schmitt can be used to combine the original prepulse and square wave outputs. Explain why this combined waveform could provide a more useful prepulse when used as a trigger signal for an oscilloscope. Sketch the idealized waveforms you would expect to observe at the various parts of your circuit showing clearly relative timing between device outputs. 9

10 5. (b) Traffic Light Controller The requirement is for a unit to provide the following sequence: Input I high: RED on, GREEN and AMBER off. Input I Low: (a) (b) (c) (d) (e) Sequence starts with RED on, GREEN and AMBER off for between 4 and 6 seconds; then RED and AMBER on, GREEN off for 2 seconds; then GREEN on, RED and AMBER off for 6 seconds; then AMBER on, GREEN and RED off for 2 seconds; then RED only for 6 seconds. The sequence should then continue with phase (b), and so on. At any stage, setting input I high should result in the RED stop condition being displayed. The logic design is based on the sequence table below: COUNTER OUTPUTS TRAFFIC LIGHTS Q D Q C Q B R A G By using Karnaugh maps or by inspection from the above table the logic expressions for the RED, AMBER and GREEN outputs in terms of the counter outputs are found to be: R = Q D A = Q C Q B G = Q D. Q C + Q D. Q B = Q D (Q C + Q B ) = Q D (Q C. Q B ) This logic design is translated straightforwardly into the circuit of Fig. 4. by de Morgan 10

11 Extra inverters have been added to drive the LED indicators. TTL outputs have lower output resistance in the LOW-level state and a more closely defined output voltage level, which is within a few tens of millivolts relative to ground. The inverters shown in Fig. 4 are the six contained in a single 74LS04 package and the NAND gates are part of a 74LS00 package. The pin connections can be found in the data. Remember that the power supply pins for each package need to be connected to +5volts (V CC) and ground (GND). 5.4 Assemble this circuit on the breadboard provided and check that it functions correctly as indicated by the RED, AMBER and GREEN LED indicators. Measure the supply current taken by the circuit and in your report check that this falls within the limits specified in the manufacturer s data for the digital ICs used. Replace the 1 Hz clock with a high frequency clock and obtain oscilloscope traces for the RED, AMBER and GREEN outputs showing the relative timing of the sequence as a whole. When a satisfactory display has been achieved, record your waveforms. 5.5 As part of your report, design a new logic circuit such that the reset condition, (I high), is changed so that RED and AMBER are ON. On restart, (with I low), the sequence is to follow that shown in section 5 (b), and GREEN only is switched ON within 2 seconds. In your report show how you derived your logic expressions, which should be simplified to use the least number of Digital IC packages of the types listed on page two. Note that exclusive-or gates are available in the 74LS86 package. Draw a full circuit diagram showing clearly outputs and connections to the appropriate LEDs, and estimate the maximum current your circuit will draw. Experiment originally developed by R.R. Thorp D.M. Holburn January

12 Appendix A The connections to the IC test socket are as shown below: 12

ENGINEERING TRIPOS PART II A ELECTRICAL AND INFORMATION ENGINEERING TEACHING LABORATORY EXPERIMENT 3B2-B DIGITAL INTEGRATED CIRCUITS

ENGINEERING TRIPOS PART II A ELECTRICAL AND INFORMATION ENGINEERING TEACHING LABORATORY EXPERIMENT 3B2-B DIGITAL INTEGRATED CIRCUITS ENGINEERING TRIPOS PART II A ELECTRICAL AND INFORMATION ENGINEERING TEACHING LABORATORY EXPERIMENT 3B2-B DIGITAL INTEGRATED CIRCUITS OBJECTIVES : 1. To interpret data sheets supplied by the manufacturers

More information

ENGINEERING TRIPOS PART II A ELECTRICAL AND INFORMATION ENGINEERING TEACHING LABORATORY EXPERIMENT 3B2-B DIGITAL INTEGRATED CIRCUITS

ENGINEERING TRIPOS PART II A ELECTRICAL AND INFORMATION ENGINEERING TEACHING LABORATORY EXPERIMENT 3B2-B DIGITAL INTEGRATED CIRCUITS ENGINEERING TRIPOS PART II A ELECTRICAL AND INFORMATION ENGINEERING TEACHING LABORATORY EXPERIMENT 3B2-B DIGITAL INTEGRATED CIRCUITS OBJECTIVES : 1. To interpret data sheets supplied by the manufacturers

More information

HIGH LOW Astable multivibrators HIGH LOW 1:1

HIGH LOW Astable multivibrators HIGH LOW 1:1 1. Multivibrators A multivibrator circuit oscillates between a HIGH state and a LOW state producing a continuous output. Astable multivibrators generally have an even 50% duty cycle, that is that 50% of

More information

ANALOG TO DIGITAL CONVERTER

ANALOG TO DIGITAL CONVERTER Final Project ANALOG TO DIGITAL CONVERTER As preparation for the laboratory, examine the final circuit diagram at the end of these notes and write a brief plan for the project, including a list of the

More information

ASTABLE MULTIVIBRATOR

ASTABLE MULTIVIBRATOR 555 TIMER ASTABLE MULTIIBRATOR MONOSTABLE MULTIIBRATOR 555 TIMER PHYSICS (LAB MANUAL) PHYSICS (LAB MANUAL) 555 TIMER Introduction The 555 timer is an integrated circuit (chip) implementing a variety of

More information

PHYSICS 536 Experiment 14: Basic Logic Circuits

PHYSICS 536 Experiment 14: Basic Logic Circuits PHYSICS 5 Experiment 4: Basic Logic Circuits Several T 2 L ICs will be used to illustrate basic logic functions. Their pin connections are shown in the following sketch, which is a top view. 4 2 9 8 +5V

More information

Analog Electronic Circuits Lab-manual

Analog Electronic Circuits Lab-manual 2014 Analog Electronic Circuits Lab-manual Prof. Dr Tahir Izhar University of Engineering & Technology LAHORE 1/09/2014 Contents Experiment-1:...4 Learning to use the multimeter for checking and indentifying

More information

OBJECTIVE The purpose of this exercise is to design and build a pulse generator.

OBJECTIVE The purpose of this exercise is to design and build a pulse generator. ELEC 4 Experiment 8 Pulse Generators OBJECTIVE The purpose of this exercise is to design and build a pulse generator. EQUIPMENT AND PARTS REQUIRED Protoboard LM555 Timer, AR resistors, rated 5%, /4 W,

More information

Module -18 Flip flops

Module -18 Flip flops 1 Module -18 Flip flops 1. Introduction 2. Comparison of latches and flip flops. 3. Clock the trigger signal 4. Flip flops 4.1. Level triggered flip flops SR, D and JK flip flops 4.2. Edge triggered flip

More information

High Current MOSFET Toggle Switch with Debounced Push Button

High Current MOSFET Toggle Switch with Debounced Push Button Set/Reset Flip Flop This is an example of a set/reset flip flop using discrete components. When power is applied, only one of the transistors will conduct causing the other to remain off. The conducting

More information

AC LAB ECE-D ecestudy.wordpress.com

AC LAB ECE-D ecestudy.wordpress.com PART B EXPERIMENT NO: 1 AIM: PULSE AMPLITUDE MODULATION (PAM) & DEMODULATION DATE: To study Pulse Amplitude modulation and demodulation process with relevant waveforms. APPARATUS: 1. Pulse amplitude modulation

More information

Basic Logic Circuits

Basic Logic Circuits Basic Logic Circuits Required knowledge Measurement of static characteristics of nonlinear circuits. Measurement of current consumption. Measurement of dynamic properties of electrical circuits. Definitions

More information

Exam Booklet. Pulse Circuits

Exam Booklet. Pulse Circuits Exam Booklet Pulse Circuits Pulse Circuits STUDY ASSIGNMENT This booklet contains two examinations for the six lessons entitled Pulse Circuits. The material is intended to provide the last training sought

More information

CD4538 Dual Precision Monostable

CD4538 Dual Precision Monostable CD4538 Dual Precision Monostable General Description The CD4538BC is a dual, precision monostable multivibrator with independent trigger and reset controls. The device is retriggerable and resettable,

More information

Process Components. Process component

Process Components. Process component What are PROCESS COMPONENTS? Input Transducer Process component Output Transducer The input transducer circuits are connected to PROCESS COMPONENTS. These components control the action of the OUTPUT components

More information

R & D Electronics DIGITAL IC TRAINER. Model : DE-150. Feature: Object: Specification:

R & D Electronics DIGITAL IC TRAINER. Model : DE-150. Feature: Object: Specification: DIGITAL IC TRAINER Model : DE-150 Object: To Study the Operation of Digital Logic ICs TTL and CMOS. To Study the All Gates, Flip-Flops, Counters etc. To Study the both the basic and advance digital electronics

More information

DM96S02 Dual Retriggerable Resettable Monostable Multivibrator

DM96S02 Dual Retriggerable Resettable Monostable Multivibrator January 1992 Revised June 1999 DM96S02 Dual Retriggerable Resettable Monostable Multivibrator General Description The DM96S02 is a dual retriggerable and resettable monostable multivibrator. This one-shot

More information

Transistor Design & Analysis (Inverter)

Transistor Design & Analysis (Inverter) Experiment No. 1: DIGITAL ELECTRONIC CIRCUIT Transistor Design & Analysis (Inverter) APPARATUS: Transistor Resistors Connecting Wires Bread Board Dc Power Supply THEORY: Digital electronics circuits operate

More information

FAMILIARIZATION WITH DIGITAL PULSE AND MEASUREMENTS OF THE TRANSIENT TIMES

FAMILIARIZATION WITH DIGITAL PULSE AND MEASUREMENTS OF THE TRANSIENT TIMES EXPERIMENT 1 FAMILIARIZATION WITH DIGITAL PULSE AND MEASUREMENTS OF THE TRANSIENT TIMES REFERENCES Analysis and Design of Digital Integrated Circuits, Hodges and Jackson, pages 6-7 Experiments in Microprocessors

More information

1 Second Time Base From Crystal Oscillator

1 Second Time Base From Crystal Oscillator 1 Second Time Base From Crystal Oscillator The schematic below illustrates dividing a crystal oscillator signal by the crystal frequency to obtain an accurate (0.01%) 1 second time base. Two cascaded 12

More information

ISO-9001 AS9120certi cation ClassQ Military

ISO-9001 AS9120certi cation ClassQ Military Datasheet RochesterElectronics ManufacturedComponents Rochester branded components are manufactured using eitherdie/wafers purchasedfrom theoriginalsuppliers orrochesterwafers recreated from the originalip.

More information

DEPARTMENT OF ELECTRICAL ENGINEERING LAB WORK EE301 ELECTRONIC CIRCUITS

DEPARTMENT OF ELECTRICAL ENGINEERING LAB WORK EE301 ELECTRONIC CIRCUITS DEPARTMENT OF ELECTRICAL ENGINEERING LAB WORK EE301 ELECTRONIC CIRCUITS EXPERIMENT : 4 TITLE : 555 TIMERS OUTCOME : Upon completion of this unit, the student should be able to: 1. gain experience with

More information

EXPERIMENT 12: DIGITAL LOGIC CIRCUITS

EXPERIMENT 12: DIGITAL LOGIC CIRCUITS EXPERIMENT 12: DIGITAL LOGIC CIRCUITS The purpose of this experiment is to gain some experience in the use of digital logic circuits. These circuits are used extensively in computers and all types of electronic

More information

Assignment /01

Assignment /01 Principles and Applications of Electronic Devices and Circuits Assignment 1 40764/01 It's very straightforward to submit this test paper online by logging on to the ICS Student Community at www.icslearn.co.uk.

More information

4-bit counter circa bit counter circa 1990

4-bit counter circa bit counter circa 1990 Digital Logic 4-bit counter circa 1960 8-bit counter circa 1990 Logic gates Operates on logical values (TRUE = 1, FALSE = 0) NOT AND OR XOR 0-1 1-0 0 0 0 1 0 0 0 1 0 1 1 1 0 0 0 1 0 1 0 1 1 1 1 1 0 0 0

More information

Number of Lessons:155 #14B (P) Electronics Technology with Digital and Microprocessor Laboratory Completion Time: 42 months

Number of Lessons:155 #14B (P) Electronics Technology with Digital and Microprocessor Laboratory Completion Time: 42 months PROGRESS RECORD Study your lessons in the order listed below. Number of Lessons:155 #14B (P) Electronics Technology with Digital and Microprocessor Laboratory Completion Time: 42 months 1 2330A Current

More information

Experiment EB2: IC Multivibrator Circuits

Experiment EB2: IC Multivibrator Circuits EEE1026 Electronics II: Experiment Instruction Learning Outcomes Experiment EB2: IC Multivibrator Circuits LO1: Explain the principles and operation of amplifiers and switching circuits LO2: Analyze high

More information

Draw in the space below a possible arrangement for the resistor and capacitor. encapsulated components

Draw in the space below a possible arrangement for the resistor and capacitor. encapsulated components 1). An encapsulated component is known to consist of a resistor and a capacitor. It has two input terminals and two output terminals. A 5V, 1kHz square wave signal is connected to the input terminals and

More information

B.E. SEMESTER III (ELECTRICAL) SUBJECT CODE: X30902 Subject Name: Analog & Digital Electronics

B.E. SEMESTER III (ELECTRICAL) SUBJECT CODE: X30902 Subject Name: Analog & Digital Electronics B.E. SEMESTER III (ELECTRICAL) SUBJECT CODE: X30902 Subject Name: Analog & Digital Electronics Sr. No. Date TITLE To From Marks Sign 1 To verify the application of op-amp as an Inverting Amplifier 2 To

More information

Breadboard Primer. Experience. Objective. No previous electronics experience is required.

Breadboard Primer. Experience. Objective. No previous electronics experience is required. Breadboard Primer Experience No previous electronics experience is required. Figure 1: Breadboard drawing made using an open-source tool from fritzing.org Objective A solderless breadboard (or protoboard)

More information

In data sheets and application notes which still contain NXP or Philips Semiconductors references, use the references to Nexperia, as shown below.

In data sheets and application notes which still contain NXP or Philips Semiconductors references, use the references to Nexperia, as shown below. Important notice Dear Customer, On 7 February 2017 the former NXP Standard Product business became a new company with the tradename Nexperia. Nexperia is an industry leading supplier of Discrete, Logic

More information

Multivibrators. Department of Electrical & Electronics Engineering, Amrita School of Engineering

Multivibrators. Department of Electrical & Electronics Engineering, Amrita School of Engineering Multivibrators Multivibrators Multivibrator is an electronic circuit that generates square, rectangular, pulse waveforms. Also called as nonlinear oscillators or function generators. Multivibrator is basically

More information

CD4538BC Dual Precision Monostable

CD4538BC Dual Precision Monostable CD4538BC Dual Precision Monostable General Description The CD4538BC is a dual, precision monostable multivibrator with independent trigger and reset controls. The device is retriggerable and resettable,

More information

Computer-Based Project on VLSI Design Co 3/8

Computer-Based Project on VLSI Design Co 3/8 Computer-Based Project on VLSI Design Co 3/8 This pamphlet describes a laboratory activity based on a former third year EIST experiment. Its purpose is the measurement of the switching speed of some CMOS

More information

CHAPTER 4: 555 TIMER. Dr. Wan Mahani Hafizah binti Wan Mahmud

CHAPTER 4: 555 TIMER. Dr. Wan Mahani Hafizah binti Wan Mahmud CHAPTE 4: 555 TIME Dr. Wan Mahani Hafizah binti Wan Mahmud 555 TIME Introduction Pin configuration Basic architecture and operation Astable Operation Monostable Operation Timer in Triggering Circuits 555

More information

i Intelligent Digitize Emulated Achievement Lab

i Intelligent Digitize Emulated Achievement Lab Electronics Circuits Equipment Intelligent Digitize Emulated Achievement Lab intelligent digitize emulated achievement lab is a digitized-based training system, which utilizes integrated Hardware Platform,

More information

Lab 12: Timing sequencer (Version 1.3)

Lab 12: Timing sequencer (Version 1.3) Lab 12: Timing sequencer (Version 1.3) WARNING: Use electrical test equipment with care! Always double-check connections before applying power. Look for short circuits, which can quickly destroy expensive

More information

INTEGRATED CIRCUITS. For a complete data sheet, please also download:

INTEGRATED CIRCUITS. For a complete data sheet, please also download: INTEGRATED CIRCUITS DATA SHEET For a complete data sheet, please also download: The IC0 74HC/HCT/HCU/HCMOS Logic Family Specifications The IC0 74HC/HCT/HCU/HCMOS Logic Package Information The IC0 74HC/HCT/HCU/HCMOS

More information

555 Timer and Its Application

555 Timer and Its Application ANALOG ELECTRONICS (AE) 555 Timer and Its Application 1 Prepared by: BE-EE Amish J. Tankariya SEMESTER-III SUBJECT- ANALOG ELECTRONICS (AE) GTU Subject Code :- 210902 2 OBJECTIVES 555 timer; What is the

More information

Dev Bhoomi Institute Of Technology Department of Electronics and Communication Engineering PRACTICAL INSTRUCTION SHEET REV. NO. : REV.

Dev Bhoomi Institute Of Technology Department of Electronics and Communication Engineering PRACTICAL INSTRUCTION SHEET REV. NO. : REV. Dev Bhoomi Institute Of Technology Department of Electronics and Communication Engineering PRACTICAL INSTRUCTION SHEET LABORATORY MANUAL EXPERIMENT NO. ISSUE NO. : ISSUE DATE: July 200 REV. NO. : REV.

More information

Lecture 02: Logic Families. R.J. Harris & D.G. Bailey

Lecture 02: Logic Families. R.J. Harris & D.G. Bailey Lecture 02: Logic Families R.J. Harris & D.G. Bailey Objectives Show how diodes can be used to form logic gates (Diode logic). Explain the need for introducing transistors in the output (DTL and TTL).

More information

LM555 and LM556 Timer Circuits

LM555 and LM556 Timer Circuits LM555 and LM556 Timer Circuits LM555 TIMER INTERNAL CIRCUIT BLOCK DIAGRAM "RESET" And "CONTROL" Input Terminal Notes Most of the circuits at this web site that use the LM555 and LM556 timer chips do not

More information

INTEGRATED CIRCUITS. For a complete data sheet, please also download:

INTEGRATED CIRCUITS. For a complete data sheet, please also download: INTEGRATED CIRCUITS DATA SHEET For a complete data sheet, please also download: The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications The IC06 74HC/HCT/HCU/HCMOS Logic Package Information The IC06 74HC/HCT/HCU/HCMOS

More information

CMOS Schmitt Trigger A Uniquely Versatile Design Component

CMOS Schmitt Trigger A Uniquely Versatile Design Component CMOS Schmitt Trigger A Uniquely Versatile Design Component INTRODUCTION The Schmitt trigger has found many applications in numerous circuits, both analog and digital. The versatility of a TTL Schmitt is

More information

Practical 2P12 Semiconductor Devices

Practical 2P12 Semiconductor Devices Practical 2P12 Semiconductor Devices What you should learn from this practical Science This practical illustrates some points from the lecture courses on Semiconductor Materials and Semiconductor Devices

More information

E85: Digital Design and Computer Architecture

E85: Digital Design and Computer Architecture E85: Digital Design and Computer Architecture Lab 1: Electrical Characteristics of Logic Gates Objective The purpose of this lab is to become comfortable with logic gates as physical objects, to interpret

More information

Classification of Digital Circuits

Classification of Digital Circuits Classification of Digital Circuits Combinational logic circuits. Output depends only on present input. Sequential circuits. Output depends on present input and present state of the circuit. Combinational

More information

Associate In Applied Science In Electronics Engineering Technology Expiration Date:

Associate In Applied Science In Electronics Engineering Technology Expiration Date: PROGRESS RECORD Study your lessons in the order listed below. Associate In Applied Science In Electronics Engineering Technology Expiration Date: 1 2330A Current and Voltage 2 2330B Controlling Current

More information

Computer-Based Project on VLSI Design Co 3/7

Computer-Based Project on VLSI Design Co 3/7 Computer-Based Project on VLSI Design Co 3/7 Electrical Characterisation of CMOS Ring Oscillator This pamphlet describes a laboratory activity based on an integrated circuit originally designed and tested

More information

multivibrator; Introduction to silicon-controlled rectifiers (SCRs).

multivibrator; Introduction to silicon-controlled rectifiers (SCRs). Appendix The experiments of which details are given in this book are based largely on a set of 'modules' specially designed by Dr. K.J. Close. These 'modules' are now made and marketed by Irwin-Desman

More information

TTL LOGIC and RING OSCILLATOR TTL

TTL LOGIC and RING OSCILLATOR TTL ECE 2274 TTL LOGIC and RING OSCILLATOR TTL We will examine two digital logic inverters. The first will have a passive resistor pull-up output stage. The second will have an active transistor and current

More information

Chapter 2 Combinational Circuits

Chapter 2 Combinational Circuits Chapter 2 Combinational Circuits SKEE2263 Digital Systems Mun im/ismahani/izam {munim@utm.my,e-izam@utm.my,ismahani@fke.utm.my} February 23, 26 Why CMOS? Most logic design today is done on CMOS circuits

More information

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad 1 P a g e INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad - 500 043 ELECTRONICS AND COMMUNICATION ENGINEERING TUTORIAL QUESTION BANK Name : INTEGRATED CIRCUITS APPLICATIONS Code

More information

Digital Logic Troubleshooting

Digital Logic Troubleshooting Digital Logic Troubleshooting Troubleshooting Basic Equipment Circuit diagram Data book (for IC pin outs) Logic probe Voltmeter Oscilloscope Advanced Logic analyzer 1 Basic ideas Troubleshooting is systemic

More information

Chapter 13: Comparators

Chapter 13: Comparators Chapter 13: Comparators So far, we have used op amps in their normal, linear mode, where they follow the op amp Golden Rules (no input current to either input, no voltage difference between the inputs).

More information

LAB 1 AN EXAMPLE MECHATRONIC SYSTEM: THE FURBY

LAB 1 AN EXAMPLE MECHATRONIC SYSTEM: THE FURBY LAB 1 AN EXAMPLE MECHATRONIC SYSTEM: THE FURBY Objectives Preparation Tools To see the inner workings of a commercial mechatronic system and to construct a simple manual motor speed controller and current

More information

R a) Explain the operation of RC high-pass circuit when exponential input is applied.

R a) Explain the operation of RC high-pass circuit when exponential input is applied. SET - 1 1. a) Explain the operation of RC high-pass circuit when exponential input is applied. 2x V ( e 1) V b) Verify V2 = = tanhx for a symmetrical square wave applied to a RC low 2x 2 ( e + 2 pass circuit.

More information

FET Driver, Load, and Switch Circuits

FET Driver, Load, and Switch Circuits Laboratory-4 FET Driver, Load, and Switch Circuits Introduction Precautions The objectives of this experiment are to observe the operating characteristics of inverter circuits which use JFETs and MOSFETs

More information

MM74HC221A Dual Non-Retriggerable Monostable Multivibrator

MM74HC221A Dual Non-Retriggerable Monostable Multivibrator September 1983 Revised January 2004 MM74HC221A Dual Non-Retriggerable Monostable Multivibrator General Description The MM74HC221A high speed monostable multivibrators (one shots) utilize advanced silicon-gate

More information

CD4047BC Low Power Monostable/Astable Multivibrator

CD4047BC Low Power Monostable/Astable Multivibrator Low Power Monostable/Astable Multivibrator General Description The CD4047B is capable of operating in either the monostable or astable mode. It requires an external capacitor (between pins 1 and 3) and

More information

ELECTRONICS ADVANCED SUPPLEMENTARY LEVEL

ELECTRONICS ADVANCED SUPPLEMENTARY LEVEL ELECTRONICS ADVANCED SUPPLEMENTARY LEVEL AIMS The general aims of the subject are : 1. to foster an interest in and an enjoyment of electronics as a practical and intellectual discipline; 2. to develop

More information

Electronics 1. Voltage/Current Resistors Capacitors Inductors Transistors

Electronics 1. Voltage/Current Resistors Capacitors Inductors Transistors Electronics 1 Voltage/Current Resistors Capacitors Inductors Transistors Voltage and Current Simple circuit a battery pushes some electrons around the circuit how many per second? Water The easiest way

More information

GCSE Electronics. Scheme of Work

GCSE Electronics. Scheme of Work GCSE Electronics Scheme of Work Week Topic Detail Notes 1 Practical skills assemble a circuit using a diagram recognize a component from its physical appearance (This is a confidence building/motivating

More information

4-bit counter circa bit counter circa 1990

4-bit counter circa bit counter circa 1990 Digital Logic 4-bit counter circa 1960 8-bit counter circa 1990 Logic gates Operates on logical values (TRUE = 1, FALSE = 0) NOT AND OR XOR 0-1 1-0 0 0 0 1 0 0 0 1 0 1 1 1 0 0 0 1 0 1 0 1 1 1 1 1 0 0 0

More information

1. LINEAR WAVE SHAPING

1. LINEAR WAVE SHAPING Aim: 1. LINEAR WAVE SHAPING i) To design a low pass RC circuit for the given cutoff frequency and obtain its frequency response. ii) To observe the response of the designed low pass RC circuit for the

More information

GCE AS. WJEC Eduqas GCE AS in ELECTRONICS ACCREDITED BY OFQUAL DESIGNATED BY QUALIFICATIONS WALES SAMPLE ASSESSMENT MATERIALS

GCE AS. WJEC Eduqas GCE AS in ELECTRONICS ACCREDITED BY OFQUAL DESIGNATED BY QUALIFICATIONS WALES SAMPLE ASSESSMENT MATERIALS GCE AS WJEC Eduqas GCE AS in ELECTRONICS ACCREDITED BY OFQUAL DESIGNATED BY QUALIFICATIONS WALES SAMPLE ASSESSMENT MATERIALS Teaching from 207 For award from 208 AS ELECTRONICS Sample Assessment Materials

More information

PreLab 6 PWM Design for H-bridge Driver (due Oct 23)

PreLab 6 PWM Design for H-bridge Driver (due Oct 23) GOAL PreLab 6 PWM Design for H-bridge Driver (due Oct 23) The overall goal of Lab6 is to demonstrate a DC motor controller that can adjust speed and direction. You will design the PWM waveform and digital

More information

LABORATORY EXPERIMENT. Infrared Transmitter/Receiver

LABORATORY EXPERIMENT. Infrared Transmitter/Receiver LABORATORY EXPERIMENT Infrared Transmitter/Receiver (Note to Teaching Assistant: The week before this experiment is performed, place students into groups of two and assign each group a specific frequency

More information

ELEC2 (JUN15ELEC201) General Certificate of Education Advanced Subsidiary Examination June Further Electronics TOTAL. Time allowed 1 hour

ELEC2 (JUN15ELEC201) General Certificate of Education Advanced Subsidiary Examination June Further Electronics TOTAL. Time allowed 1 hour Centre Number Surname Candidate Number For Examiner s Use Other Names Candidate Signature Examiner s Initials Question Mark Electronics General Certificate of Education Advanced Subsidiary Examination

More information

AND ITS APPLICATIONS M.C.SHARMA

AND ITS APPLICATIONS M.C.SHARMA AND ITS APPLICATIONS M.C.SHARMA 555 TIMER AND ITS APPLICATIONS BY M. C. SHARMA, M. Sc. PUBLISHERS: BUSINESS PROMOTION PUBLICATIONS 376, Lajpat Rai Market, Delhi-110006 By the same author Transistor Novelties

More information

DATA SHEET. HEF4047B MSI Monostable/astable multivibrator. For a complete data sheet, please also download: INTEGRATED CIRCUITS

DATA SHEET. HEF4047B MSI Monostable/astable multivibrator. For a complete data sheet, please also download: INTEGRATED CIRCUITS INTEGRATED CIRCUITS DATA SHEET For a complete data sheet, please also download: The IC04 LOCMOS HE4000B Logic Family Specifications HEF, HEC The IC04 LOCMOS HE4000B Logic Package Outlines/Information HEF,

More information

Multi-Transistor Configurations

Multi-Transistor Configurations Experiment-3 Multi-Transistor Configurations Introduction Comment The objectives of this experiment are to examine the operating characteristics of several of the most common multi-transistor configurations,

More information

LINEAR IC APPLICATIONS

LINEAR IC APPLICATIONS 1 B.Tech III Year I Semester (R09) Regular & Supplementary Examinations December/January 2013/14 1 (a) Why is R e in an emitter-coupled differential amplifier replaced by a constant current source? (b)

More information

CD4541BC Programmable Timer

CD4541BC Programmable Timer CD4541BC Programmable Timer General Description The CD4541BC Programmable Timer is designed with a 16-stage binary counter, an integrated oscillator for use with an external capacitor and two resistors,

More information

DUAL STEPPER MOTOR DRIVER

DUAL STEPPER MOTOR DRIVER DUAL STEPPER MOTOR DRIVER GENERAL DESCRIPTION The is a switch-mode (chopper), constant-current driver with two channels: one for each winding of a two-phase stepper motor. is equipped with a Disable input

More information

St.MARTIN S ENGINEERING COLLEGE

St.MARTIN S ENGINEERING COLLEGE St.MARTIN S ENGINEERING COLLEGE Dhulapally, Kompally, Secunderabad-500014. Branch Year&Sem Subject Name : Electrical and Electronics Engineering : III B. Tech I Semester : IC Applications OBJECTIVES QUESTION

More information

CHAPTER 6 DIGITAL INSTRUMENTS

CHAPTER 6 DIGITAL INSTRUMENTS CHAPTER 6 DIGITAL INSTRUMENTS 1 LECTURE CONTENTS 6.1 Logic Gates 6.2 Digital Instruments 6.3 Analog to Digital Converter 6.4 Electronic Counter 6.6 Digital Multimeters 2 6.1 Logic Gates 3 AND Gate The

More information

Lab 2 Revisited Exercise

Lab 2 Revisited Exercise Lab 2 Revisited Exercise +15V 100k 1K 2N2222 Wire up led display Note the ground leads LED orientation 6.091 IAP 2008 Lecture 3 1 Comparator, Oscillator +5 +15 1k 2 V- 7 6 Vin 3 V+ 4 V o Notice that power

More information

ML4818 Phase Modulation/Soft Switching Controller

ML4818 Phase Modulation/Soft Switching Controller Phase Modulation/Soft Switching Controller www.fairchildsemi.com Features Full bridge phase modulation zero voltage switching circuit with programmable ZV transition times Constant frequency operation

More information

Sequential Logic Circuits

Sequential Logic Circuits Exercise 2 Sequential Logic Circuits 1 - Introduction Goal of the exercise The goals of this exercise are: - verify the behavior of simple sequential logic circuits; - measure the dynamic parameters of

More information

Practical 2P12 Semiconductor Devices

Practical 2P12 Semiconductor Devices Practical 2P12 Semiconductor Devices What you should learn from this practical Science This practical illustrates some points from the lecture courses on Semiconductor Materials and Semiconductor Devices

More information

Dev Bhoomi Institute Of Technology Department of Electronics and Communication Engineering PRACTICAL INSTRUCTION SHEET

Dev Bhoomi Institute Of Technology Department of Electronics and Communication Engineering PRACTICAL INSTRUCTION SHEET Dev Bhoomi Institute Of Technology Department of Electronics and Communication Engineering PRACTICAL INSTRUCTION SHEET LABORATORY MANUAL EXPERIMENT NO. ISSUE NO. : ISSUE DATE: REV. NO. : REV. DATE : PAGE:

More information

Physics 335 Lab 1 Intro to Digital Logic

Physics 335 Lab 1 Intro to Digital Logic Physics 33 Lab 1 Intro to Digital Logic We ll be introducing you to digital logic this quarter. Some things will be easier for you than analog, some things more difficult. Digital is an all together different

More information

Step Response of RC Circuits

Step Response of RC Circuits EE 233 Laboratory-1 Step Response of RC Circuits 1 Objectives Measure the internal resistance of a signal source (eg an arbitrary waveform generator) Measure the output waveform of simple RC circuits excited

More information

Design and Technology

Design and Technology E.M.F, Voltage and P.D E.M F This stands for Electromotive Force (e.m.f) A battery provides Electromotive Force An e.m.f can make an electric current flow around a circuit E.m.f is measured in volts (v).

More information

Fig 1: The symbol for a comparator

Fig 1: The symbol for a comparator INTRODUCTION A comparator is a device that compares two voltages or currents and switches its output to indicate which is larger. They are commonly used in devices such as They are commonly used in devices

More information

EECE 143 Lecture 0: Intro to Digital Laboratory

EECE 143 Lecture 0: Intro to Digital Laboratory EECE 143 Lecture 0: Intro to Digital Laboratory Syllabus * Class Notes Laboratory Equipment Experiment 0 * Experiment 1 Introduction Instructor Information: Mr. J. Christopher Perez Room: Haggerty Engineering,

More information

Hello, and welcome to the TI Precision Labs video discussing comparator applications, part 4. In this video we will discuss several extra features

Hello, and welcome to the TI Precision Labs video discussing comparator applications, part 4. In this video we will discuss several extra features Hello, and welcome to the TI Precision Labs video discussing comparator applications, part 4. In this video we will discuss several extra features that are integrated into some comparators to help simplify

More information

Physics 309 Lab 3 Bipolar junction transistor

Physics 309 Lab 3 Bipolar junction transistor Physics 39 Lab 3 Bipolar junction transistor The purpose of this third lab is to learn the principles of operation of a bipolar junction transistor, how to characterize its performances, and how to use

More information

UMAINE ECE Morse Code ROM and Transmitter at ISM Band Frequency

UMAINE ECE Morse Code ROM and Transmitter at ISM Band Frequency UMAINE ECE Morse Code ROM and Transmitter at ISM Band Frequency Jamie E. Reinhold December 15, 2011 Abstract The design, simulation and layout of a UMAINE ECE Morse code Read Only Memory and transmitter

More information

EE283 Electrical Measurement Laboratory Laboratory Exercise #7: Digital Counter

EE283 Electrical Measurement Laboratory Laboratory Exercise #7: Digital Counter EE283 Electrical Measurement Laboratory Laboratory Exercise #7: al Counter Objectives: 1. To familiarize students with sequential digital circuits. 2. To show how digital devices can be used for measurement

More information

1 sur 8 07/04/ :06

1 sur 8 07/04/ :06 1 sur 8 07/04/2012 12:06 Les Banki Circuit Updated Version August 16, 2007 Synchronized 3 Frequency PWM circuit & cell drivers (for resonance electrolysis of water) Background The basic idea for this design

More information

GCSE (9-1) WJEC Eduqas GCSE (9-1) in ELECTRONICS ACCREDITED BY OFQUAL DESIGNATED BY QUALIFICATIONS WALES SAMPLE ASSESSMENT MATERIALS

GCSE (9-1) WJEC Eduqas GCSE (9-1) in ELECTRONICS ACCREDITED BY OFQUAL DESIGNATED BY QUALIFICATIONS WALES SAMPLE ASSESSMENT MATERIALS GCSE (9-1) WJEC Eduqas GCSE (9-1) in ELECTRONICS ACCREDITED BY OFQUAL DESIGNATED BY QUALIFICATIONS WALES SAMPLE ASSESSMENT MATERIALS Teaching from 2017 For award from 2019 GCSE ELECTRONICS Sample Assessment

More information

Electricity and Electronics Constructor Kits

Electricity and Electronics Constructor Kits EEC470 Series The Electricity and Electronics Constructor EEC470 series is a structured practical training programme comprising an unpowered construction deck (EEC470) and a set of educational kits. Each

More information

ELEC3106 Electronics. Lab 3: PCB EMI measurements. Objective. Components. Set-up

ELEC3106 Electronics. Lab 3: PCB EMI measurements. Objective. Components. Set-up ELEC3106 Electronics Lab 3: PCB EMI measurements Objective The objective of this laboratory session is to give the students a good understanding of critical PCB level Electromagnetic Interference phenomena

More information

Electronic Circuits EE359A

Electronic Circuits EE359A Electronic Circuits EE359A Bruce McNair B206 bmcnair@stevens.edu 201-216-5549 1 Memory and Advanced Digital Circuits - 2 Chapter 11 2 Figure 11.1 (a) Basic latch. (b) The latch with the feedback loop opened.

More information

CMOS Schmitt Trigger A Uniquely Versatile Design Component

CMOS Schmitt Trigger A Uniquely Versatile Design Component CMOS Schmitt Trigger A Uniquely Versatile Design Component INTRODUCTION The Schmitt trigger has found many applications in numerous circuits both analog and digital The versatility of a TTL Schmitt is

More information

In this experiment you will study the characteristics of a CMOS NAND gate.

In this experiment you will study the characteristics of a CMOS NAND gate. Introduction Be sure to print a copy of Experiment #12 and bring it with you to lab. There will not be any experiment copies available in the lab. Also bring graph paper (cm cm is best). Purpose In this

More information

74VHC4046 CMOS Phase Lock Loop

74VHC4046 CMOS Phase Lock Loop 74VHC4046 CMOS Phase Lock Loop General Description The 74VHC4046 is a low power phase lock loop utilizing advanced silicon-gate CMOS technology to obtain high frequency operation both in the phase comparator

More information

EE2304 Implementation of a Stepper Motor using CMOS Devices Fall 2004 WEEK -2-

EE2304 Implementation of a Stepper Motor using CMOS Devices Fall 2004 WEEK -2- WEEK -2-1. Objective Design a controller for a stepper motor that will be capable of: Making the motor rotate with variable speed (the user should be able to adjust the rotational speed easily and without

More information