Mapletree Audio Design SR70A Special Red Driver Module for Dynaco ST-70
|
|
- Milo Bailey
- 5 years ago
- Views:
Transcription
1 Mapletree Audio Design S70A Special ed Driver Module for Dynaco ST-70 Installation instructions ev. Jan. 9/ The Special ed S70A driver module is a drop in replacement for the original driver board of the Dynaco ST-70 power amplifier. Unlike the original, all wiring on the S70A is point-to-point with connections to the amplifier made to turret terminals. The schematic diagram of the S70A module identifies the turret connections to the ST-70 circuitry. The instructions identify which of the original wires and components are to be removed and discarded and the new wiring that is required using the silver-plated Teflon wire supplied. When making a new connection from one of the S70A turrets to a point in the amplifier, first route the wire as shown in the diagram in order to obtain the correct length. Then strip ¼ inch of insulation from each end and melt a small amount of solder on the exposed wire by heating it with your soldering iron and melting the solder on to the wire (pre-tinning). The best connection to a turret is made by inserting the pre-tinned end of the wire into the hole in the top of the turret, leaving a bit of wire exposed, then heating the turret with your soldering iron while adding solder so it runs down the wire inside the turret. Note: It may be necessary to remove the s on the front apron of the ST-70 to allow room for the S70A board. If this has not already been done in previous modifications to your amplifier, the following instructions should be followed.. Unsolder both ends of all wires connected to the lugs of the two s on the front apron of the ST-70.. emove the sockets.. The stainless steel filler plates supplied can be attached to the inside of the chassis using the original socket machine screws or the # sheet metal screws supplied.. If it is desired to provide external access to the bias test voltage for the ELs, you can mount suitable test jacks in the filler plates, making sure you maintain clearance for the S70A board. These jacks should be wired to lug of V (L) and V (). The bias test voltage (. V) is then measured from each jack to the chassis (ground). efer to Figure showing the original wiring to the printed circuit board, with the s removed.
2 . Unsolder all wires and resistors from the input CA jacks and stereo-mono switch on the front panel. This assumes that the stereo-mono switch will not be used.. Unsolder both ends of all wires connected to the eyelets on the original board that are marked with an. The two wires connected to the Ohm taps of the output transformer should only be unsoldered from the eyelets on the circuit board.. emove the original board from the chassis.. Install the S70A board using the original screws/nuts or the -0 screws and hex nuts supplied.. Unsolder the K resistor between lugs and of the original -section filter capacitor and discard. efer to the wiring diagram for the S70A board connections (Figure ).. Solder the twisted pairs of wires pre-soldered to lugs 7 and of the SL7 tubes V (left) and V (right) on the S70A board to lugs and 7 of V (L) and and 7 of V ().. Solder the wires coming from the Ohm speaker terminals on the rear panel to the FBL and FB turrets on the S70A board.. Measure, cut, and strip silver-plated Teflon wire lengths and make the following connections: i. CA left input jack ground lug to CA right input jack ground lug ii. CA left input jack ground lug to the S 70A ground (GND) bus iii. CA left input signal lug to turret iv. CA right input signal lug to IN turret v. Filter capacitor lug to turret B vi. Filter capacitor lug to turret B vii. Chassis ground lug (next to filter capacitor) to the S70A ground bus viii. Center lug () of the right bias potentiometer to the Bias turret ix. Center lug () of the left bias potentiometer to the turret x. Lug of V (EL) to turret G xi. Lug of V7 (EL) to turret G7 xii. Lug of V (EL) to turret G xiii. Lug of V (EL) to turret G This completes the installation of the S70A module. e-check all connections using the wiring diagram as a guide. Install the four tubes with the SJ7s toward the front of the chassis. It is recommended that you re-adjust the bias for the output tubes in the usual manner. Notes:. The S70A can be supplied with a heater voltage of VDC, 0. A for each channel if desired.. If non-stock Dynaco output transformers are installed, it may be necessary to adjust the value of C (70 pf) in each channel for optimum transient response (as evidenced by the best square wave reproduction and/or the flattest high frequency response).
3 and wiring removed and wiring removed Unsolder and remove all wires and components from input jacks and stereo-mono switch original driver board Unsolder both ends of all wires and components marked and discard.. unsolder at eyelet end only unsolder at eyelet end only S Board Installation FIgure
4 stereo-mono switch filler plate input jacks L filler plate TWISTED WIES L L V FBL GND BUS B B B B FB gnd bus V V G G G G7 G FBL G G V Bias Bias G7 G G Bias G G7 FB IN IN B B TWISTED WIES S Board Installation FIgure
5 Mapletree Audio Design S70A Special ed driver module for Dynaco ST-70 Copyright Lloyd Peppard 00- rev. Jan. / IGHT. Input IN FB To Ohm tap on right OPT SJ7/9/SJ7GT.K 00 Gnd Bus C 70 pf 9 V C 0.07/00.K V 00K 7 C /00 7 SJ7 7 SL7 V SL7GT/9 C 00p To. heater voltage (Lugs and 7 of V) V.K 9 0 C 0./00 C 0./00 G7 Bias G Pin of V7 (EL with white/blue plate lead). bias pot -. V Pin of V (EL with blue plate lead) 0K W % L. Input V SJ7/9/SJ7GT. V.K 00 Gnd Bus C 70 pf V C 0.07/00 00K FBL 9 V.K To Ohm tap on left OPT B LEFT C 00p 7 C /00 7 SJ7 7 SL7 V SL7GT/9 To L. heater voltage (lugs and 7 of V) V.K B C 0./ C 0./00 G G Pin of V (EL with white/blue plate lead) L. bias pot -. V Pin of V (EL with blue plate lead) V V 97 V remove + V + K +.K + + Gnd lug on chassis Quad filter capacitor Plate voltage = V Screen voltage = V
Stealth 60i Integrated Stereo/Mono Power Amplifier
Stealth 60i Integrated Stereo/Mono Power Amplifier Users' Manual (Beta) Rev. Apr. 11/16 Mapletree Audio Design Lloyd Peppard R. R. 1, Seeley's Bay, Ontario, Canada, K0H 2N0 (613) 387-3830 info@mapletreeaudio.com
More informationD. Gillespie Designs. SCA-35 Capacitor Board. Installation Manual. D. Gillespie Designs with EFB TM
D. Gillespie Designs SCA-5 Capacitor Board with EFB TM Installation Manual D. Gillespie Designs www.tronola.com Thank you for choosing our SCA-5 Capacitor Board with *EFB. We feel it is the single most
More informationPower Supply Board. by Classic Valve Design for the Dynaco Mark-III with failsafe bias and balance
Power Supply Board by Classic Valve Design for the Dynaco Mark-III with failsafe bias and balance Classic Valve Design assumes no responsibility for circuit or user damage from the use or misuse of these
More informationDIY Tube Stereo 70 Board - TubeZone Assembled -Instructions - Page 1
DIY Tube Stereo 70 Board - TubeZone Assembled -Instructions - Page 1 Board and portions of manual, (c) 2006 Shannon Parks & DIYtube.com. Version specific instructions (c) 2006 Ned Carlson and Tubezone.net
More informationDynaco MK3 Electrolytic Cap Upgrade Assembly, Installation, and Adjustment Manual
Page 1 PC-M3U Rev 1 I. Introduction Thanks for your purchase of our Mark 3 Quad Electrolytic Capacitor Replacement Board PC-M3U. It has been designed to replace the original Dynaco Quad (4 section) Aluminum
More informationSuper Stealth Monobloc Power Amplifier
Super Stealth Monobloc Power Amplifier Special Edition Users' Manual Rev. Oct. /1 Mapletree Audio Design Lloyd Peppard R. R. 1, Seeley's Bay, Ontario, Canada, K0H N0 (61) -0 info@mapletreeaudio.com http://www.mapletreeaudio.com
More informationMarchand Electronics Inc
. PO Box 8099, Rochester NY 8 Tel:(8) 0 Fax:(8) 97 info@marchandelec.com www.marchandelec.com (c)00, 00. LN Phono Preamp REV 070 Parts List R R R R R R R7 R8 R9 R0 R R R R R R R7 R8 R9 R0 R R 9K9 K00 00
More informationNew Life for the AM6154 and AM6155 John, W1AN 29 July, 2014
New Life for the AM6154 and AM6155 John, W1AN 29 July, 2014 There are numerous sources for conversion information and modifications that have been shared over the years for the FAA AM6154 and AM6155 amplifiers
More informationMono Amplifier. LM386 Headphone Amp
Mono Amplifier LM386 Headphone Amp Layout On/Off Switch - cuts power to the circuit Mono Input Jack: use either L or R or solder together Schematic Step 1 - Parts List 1.) R1-10ohm Resistor - Brown Black
More informationSpecimen Products Single Ended Stereo Amp Instruction Book
Specimen Products Single Ended Stereo Amp Instruction Book Specimen tube amplifier designs are informed by decades of servicing and building musical instrument amps. As a result of being subjected to the
More informationSuper Stealth + Monobloc Power Amplifier
Super Stealth Monobloc Power Amplifier Users' Manual Rev. Nov. 9/ Mapletree Audio Design Lloyd Peppard R. R., Seeley's Bay, Ontario, Canada, K0H N0 (6) 7-0 info@mapletreeaudio.com http://www.mapletreeaudio.com
More informationUltra 4B SE Special Edition. Stereo Phono/Line Preamplifier
Modular Series Ultra B SE Special Edition Stereo Phono/Line Preamplifier User s Manual Phono Line Line Balance Volume Mapletree Audio Design Ultra B SE Stereo Preamplifier Rev. Feb. / Mapletree Audio Design
More informationEar+ Purist HD. Ear+ HD High Definition Stereo Headphone Amplifier
Ear Purist HD Ear HD High Definition Stereo Headphone Amplifier 2AX7 Users' Manual ev Oct. 7/3 Mapletree Audio Design loyd Peppard.., Seeley's Bay, Ontario, Canada, K0H 2N0 (63) 387-3830 www.mapletreeaudio.com
More informationSimple EL84 Basic layout. DIY Paradise 13 June 2003
Simple EL84 Basic layout DIY Paradise 13 June 2003 EL84 doesn t sing without feedback. EL84 has no bass. These are comments I gleamed off the World Wide Web from various places. The truth is, if the circuit
More informationSome KWM-2/2A Tricks. January By Georges, F6CER CCAE# 098. Some KWM-2/2A Tricks -
Some KWM-2/2A Tricks January 2016 By Georges, F6CER CCAE# 098 Some KWM-2/2A Tricks Most of the KWM-2 transceivers that can be found in Europe belong to the first generation manufactured at the beginning
More informationTHE THUNDERDRIVE (K-950)
THE THUNDERDRIVE (K-950) OUTPUT DISTORTION Unplug when not in use to save battery life. TO AMP IN The Thunderdrive Modkitsdiy.com FROM GUITAR OUT Use these instructions to learn: How to build an effects
More informationINSTRUCTIONS FOR ASSEMBLY AND OPERATION
diytube stereo 0 driver board INSTRUCTIONS FOR ASSEMBLY AND OPERATION Price $0.00 Important Note: The phase is swapped on the diytube ST0 from the orginal design. Be sure to hook up the drive lines (at
More informationManual Version July 2007
Manual Version 1.2 - July 2007 Page 1 Table of Contents Section1: M3 Phono Board Build...3 Phono Board Parts List...3 Preparation...4 Fitting the Valve Bases...6 Installing the Resistors...7 Starting the
More informationTHE ZEN TRIODE EXPIREMENTERS AMPLIFIER KIT MODEL SE84CDIYMONO
THE ZEN TRIODE EXPIREMENTERS AMPLIFIER KIT MODEL SE84CDIYMONO ASSEMBLY INSTRUCTIONS 2008 The circuit board has been designed to be used in 2 ways; A) Mounted on stand-offs to a piece of wood and B) Mounted
More informationSCA-35 System Capacitor Module Assembly & Instruction Manual
SCA-35 System Capacitor Module Assembly & Instruction Manual I. Introduction Thank you for your purchase of our SCA35-CAP System Capacitor Module. It has been designed to replace both the power supply
More informationThe Wave (K-MOD103) GUITAR DWELL REVERB REVERB SWITCH ON OUT OFF
The Wave (K-MOD103) OUT IN GUITAR IN DWELL REVERB REVERB SWITCH ON GUITAR OUT POWER ON OFF OFF Please note, there are no labels for this kit. The controls, switches and connectors have only been labeled
More informationInstructions MODIFICATION KIT MODEL SBM - 1O2-1 INTRODUCTION PARTS LIST FOR THE
Instructions FOR THE MODIFICATION KIT MODEL SBM - 1O2-1 INTRODUCTION This modification Kit applies to the following Heath Transceivers: 1. All Models HW-100, SB-100, SB-101 and SB-101W. 2. Any Model SB-102
More informationBuild Your Own Clone Chancellor Kit Instructions
Build Your Own Clone Chancellor Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationSoftRock v6.0 Builder s Notes. May 22, 2006
SoftRock v6.0 Builder s Notes May 22, 2006 Be sure to use a grounded tip soldering iron in building the v6.0 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),
More informationMarchand Electronics Inc
. PO Box 8099, Rochester NY 8 Tel:(585) 3 0 Fax:(585) 3 9375 info@marchandelec.com www.marchandelec.com (c)00. MB Push-pull tube amplifier www.marchandelec.com 585 3 0 Parts List A section R R R3 R R5
More informationValve Junior Modification
Valve Junior Modification Rob Marshall Spring 2010 Physics of Musical Instruments Table of Contents Pages 1 2...Information about the amplifier Pages 3 4...Modifications made Page 5 7...Replacement of
More informationTelecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering tips: Removing Current Wiring: Step 1. Step 2.
Telecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers Wire Strippers 3/8 Drill Bit 5/32 Drill Bit
More informationBalanced Modulator. Model 9748 Assembly and Using Manual PAiA Corporation
Balanced Modulator Model 9748 Assembly and Using Manual This second-generation 9700-series processing element for modular sound synthesizers is designed to provide great sound and excellent value. Audio
More informationInstructions for Lighting an S Scale Caboose
Instructions for Lighting an S Scale Caboose The S Scale Caboose lighting kit is adaptable for most caboose models of rolling stock including American Flyer (TM) and contains the same components as found
More informationFUNCTION GENERATOR KIT
FUNCTION GENERATOR KIT MODEL FG-500K Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 2005 by Elenco Electronics, Inc. All rights reserved. Revised 2005 REV-B 753069 No part of this book
More informationSound advice for Mapletree owners, customers, and DIYs Issue 7, March, Web:
MPLETREE RNCHES Sound advice for Mapletree owners, customers, and DIYs Issue 7, March, 07 Web: www.mapletreeaudio.com email: info@mapletreeaudio.com Focus on customization of Mapletree products: signal
More informationEar+ Purist HD. Ear+ HD II High Definition Stereo Headphone Amplifier
Ear+ Purist HD Ear+ HD II High Definition Stereo Headphone Amplifier Users' Manual Rev Mar 8/19 Mapletree Audio Design R. R. 1, Seeley's Bay, Ontario, Canada, K0H 2N0 (613) 387-3830 www.mapletreeaudio.com
More informationTHE RING RESONATOR (K-975)
THE RING RESONATOR (K-975) OUTPUT BOOST The Ring Resonator An Octave Up Fuzz Modkitsdiy.com 9 VDC CENTER (-) ADAPTER TO AMP IN FROM GUITAR OUT Unplug when not in use to save battery life. Use these instructions
More informationTHE AGGRESSOR (K-995)
THE AGGRESSOR (K-99) TONE VOLUME DISTORTION MID-SHIFT SWITCH LED The Aggressor Distortion Pedal Modkitsdiy.com 9 VDC CENTER (-) ADAPTER TO AMP IN FROM GUITAR OUT Unplug when not in use to save battery
More informationJason Stull. Physics 498 (Physics of Music) Valve Junior Modification 5/13/2010
Jason Stull Physics 498 (Physics of Music) Valve Junior Modification 5/13/2010 1 Introduction My original idea for a class project was to build a tube guitar amplifier. I have wanted a tube amp for some
More informationMAINTENANCE MANUAL MDX POWER AMPLIFIER BOARDS 19D904792G2 ( MHz) 19D904792G1 ( MHz) 19D904792G3 ( MHz)
MAINTENANCE MANUAL MDX POWER AMPLIFIER BOARDS 19D904792G2 (403-440 MHz) 19D904792G1 (440-470 MHz) 19D904792G3 (470-512 MHz) TABLE OF CONTENTS Page DESCRIPTION... 1 CIRCUIT ANALYSIS... 1 SERVICE NOTES...
More informationAssembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
More informationCALRAD 25 series - potentiometers
25 series - potentiometers audio /linear SUB-MINIATURE VOLUME CONTROLS Linear taper, extremely smooth for quiet operation. 1 2" dia. fits into 1 4" hole. Shaft 3 16" dia. Thread length 7 32", shaft length
More informationInstruction Manual. CT101 line stage / linear preamplifier module
CT0 line stage / linear preamplifier module CT0 CONTENT UNPACKG channel line stage / linear preamplifier module Unpacking Connections Definitions Power supply Signal input Signal output Volume control
More informationTHE TRILL TREMOLO (K-960)
THE TRILL TREMOLO (K-60) DEPTH SPEED The Trill Tremolo Modkitsdiy.com Unplug when not in use to save battery life. TO AMP IN FROM GUITAR OUT Use these instructions to learn: How to build an effects pedal
More informationBuild Your Own Clone Tremolo Kit Instructions
Build Your Own Clone Tremolo Kit Instructions Warranty: BYOC, LLC guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect. Soldering,
More informationPowerAmp Design. PowerAmp Design EVAL189 EVALUATION KIT FOR MODEL PAD189. Rev B
PowerAmp Design EVALUATION KIT FOR MODEL PAD189 Rev B INTRODUCTION The evaluation kit provides a convenient method to become familiar with the operation of amplifier model PAD189 before your application
More informationBRIDGE MODE FOR THE STEREO 120. Preface to Everything PLEASE READ THIS FIRST! YOU MAY SAVE YOURSELF A LOT OF TROUBLE!
BRIDGE MODE FOR THE STEREO 120 Preface to Everything PLEASE READ THIS FIRST! YOU MAY SAVE YOURSELF A LOT OF TROUBLE! At some point I made 4 Ohm 1 khz output power tests of single channels of the updated
More informationSoftRock v5.0 Builder s Notes. December 12, Building a QSD Kit
SoftRock v5.0 Builder s Notes December 12, 2005 Building a QSD Kit Be sure to use a grounded tip soldering iron in building the QSD board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),
More informationLESLIE CONSOLE CONNECTOR KIT 8400 INSTALLATION INSTRUCTIONS
LESLIE CONSOLE CONNECTOR KIT 8400 INSTALLATION INSTRUCTIONS FOR USE WITH: LESLIE Speaker Models: 122, 122RV, 222, or 222RV in conjunction with HAMMOND Speaker HAMMOND Organ Models: A, B, C, D, E, RT, BV,
More informationDynaco ST-70 Input Board
A u dio L ab s Sheldon Stokes 11811 Island Cove Dr. Fort Wayne, IN 46845 stokes@spinn.net http://www.quadesl.com Dynaco ST-70 Input Board 1 Introduction This board is a drop-in replacement for the original
More informationSTEP 0 Prepare the Materials.
How to Build a Germanium Fuzz Guitar Effect. This document will guide you to build and test your Germanium Fuzz guitar pedal. With all the materials on hand, it takes around 2-4 hours to build it. Try
More informationStarving Student II. Starving Student II. SS2 guide. Written By: 6L guides.diyaudio.com/ Page 1 of 24
SS2 guide Written By: 6L6 2019 guides.diyaudio.com/ Page 1 of 24 INTRODUCTION This is a build guide for the hybrid headphone/pre-amplifier. You can buy a kit at the SSII product listing on the diyaudio
More informationBuild Your Own Clone Classic Overdrive Kit Instructions
Build Your Own Clone Classic Overdrive Kit Instructions Warranty: BYOC, LLC guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of
More informationSoftRock v6.0 Builder s Notes. April 6, 2006
SoftRock v6.0 Builder s Notes April 6, 006 Be sure to use a grounded tip soldering iron in building the v6.0 SoftRock circuit board. The soldering iron needs to have a small tip, (0.05-0. inch diameter),
More informationINTRODUCTION FEATURES SPECIFICATIONS. Built-in Crossover
INTRODUCTION Congratulations on your purchase of a LEGACY ICON Car Amplifier. The unit is the result of an extensive engineering project to create the finest automotive high fidelity product available.
More informationAssembly Instructions for the FRB FET FM 70 Watt Amp
Assembly Instructions for the FRB FET FM 70 Watt Amp 1.) Orient the circuit board with the diagram 2.) Use a narrow chisel tip 25-30 watt soldering iron for assembly 3.) All the small parts are taped onto
More informationDIODE / TRANSISTOR TESTER KIT
DIODE / TRANSISTOR TESTER KIT MODEL DT-100K Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 1988 Elenco Electronics, Inc. Revised 2002 REV-K 753110 DT-100 PARTS LIST If you are a student,
More informationSERVICE BULLETIN. Description: VOX\ICS Tie Line Subassembly Document #: AMS44\603-0 Service Bulletin #: 002
SERVICE BULLETIN NAT Part #: AMS44 Description: VOX\ICS Tie Line Subassembly Document #: AMS44\603-0 Service Bulletin #: 002 1. Planning Information 1.1 Applicability All dual channel audio controllers:
More informationA 75-Watt Transmitter for 3 Bands Simplified Shielding and Filtering for TVI BY DONALD H. MIX, W1TS ARRL Handbook 1953 and QST, October 1951
A 75-Watt Transmitter for 3 Bands Simplified Shielding and Filtering for TVI BY DONALD H. MIX, W1TS ARRL Handbook 1953 and QST, October 1951 The transmitter shown in the photographs is a 3-stage 75-watt
More informationMAINTENANCE MANUAL. MDX POWER AMPLIFIER BOARDS 19D904792G2 ( MHz) 19D904792G1 ( MHz) 19D904792G3 ( MHz) TABLE OF CONTENTS
LBI-39051C MAINTENANCE MANUAL MDX POWER AMPLIFIER BOARDS 19D904792G2 (403-440 MHz) 19D904792G1 (440-470 MHz) 19D904792G3 (470-512 MHz) TABLE OF CONTENTS Page DESCRIPTION... 1 CIRCUIT ANALYSIS... 1 SERVICE
More informationPowerAmp Design EVALUATION KIT FOR MODELS PAD138/ PAD139/ PAD141
PowerAmp Design EVALUATION KIT FOR MODELS PAD138/ PAD139/ PAD141 Rev C INTRODUCTION The evaluation kit provides a convenient method to become familiar with the operation of amplifier models PAD138, PAD139
More informationOctal Duo Stereo Headphone Amplifier
Octal Duo Stereo Headphone Amplifier Users' Manual Rev Oct. 12/14 Mapletree Audio Design Al Freundorfer R. R. 1, Seeley's Bay, Ontario, Canada, K0H 2N0 (613) 387 3830 www.mapletreeaudio.com info@mapletreeaudio.com
More informationAM RADIO KIT MODEL AM-780K. Assembly and Instruction Manual
AM RADIO KIT MODEL AM-780K Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 2007, 1999 by Elenco Electronics, Inc. All rights reserved. Revised 2007 REV-F 753108 No part of this book
More informationHoffman AB763-2 Channel BOM
Updated 5/21/2018 Item Component Wattage Notes R1 1m 1/2 watt R2 1m 1/2 watt R3 33k 1/2 watt Single input jack R3 68k 1/2 watt Dual input jacks R4 33k 1/2 watt Single input jack R4 68k 1/2 watt Dual input
More informationRITEK RIT for Collins KWM-2/2A 10/01/2002
RITEK RIT for Collins KWM-2/2A 10/01/2002 The RITEK RIT (receiver incremental tuning) control was developed for KWM-2/2A in 1992 to "clarify" received signals differing from the transmit frequency indicated
More informationTHE STEP LADDER (K-978)
THE STEP LADDER (K-978) Footswitch True-bypass = 0 db OUTPUT INPUT Ground shunt switching on the input jack keeps the amp quiet when unplugged from the Step Ladder. Attenuator Pot Full clockwise = 0 db
More informationTen-Tec Orion Sub Receiver VHF Filter Modification Prepared by Rick Williams, VE7TK
Ten-Tec Orion Sub Receiver VHF Filter Modification Prepared by Rick Williams, VE7TK (Note: Those undertaking this modification do so at their own risk. The procedures outline a method of installing an
More informationBuild Your Own Clone Reverb Kit Instructions
Build Your Own Clone Reverb Kit Instructions Warranty: BYOC, LLC guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect. Soldering,
More informationBuild Your Own Clone Spring Reverb Kit Instructions
Build Your Own Clone Spring Reverb Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationICOM R10 Receiver Modification to Provide S-Meter Output
ICOM R10 Receiver Modification to Provide S-Meter Output A Technical Application Note from Doppler Systems Inc. Acknowledgements April 21, 2001 Revised June 6, 2004 This application note was submitted
More informationFixing/Rebuilding a Rickenbacker M-10
Fixing/Rebuilding a Rickenbacker M-10 James Milsk Physics 498 May 9, 2005 Professor Errede 1 My uncle had given me a 1950 s-era Rickenbacker M-10 guitar amplifier to fix because he tried plugging a guitar
More informationINSTRUCTIONS FOR ASSEMBLY OPERATION
diytube stereo power amplifier rev c INSTRUCTIONS FOR ASSEMBLY OPERATION Price $0.00 Disclaimer Under no circumstances does diytube assume liability or responsibility for injury or damages sustained in
More informationStereo 3.7W Class D Audio Amplifier
Stereo 3.7W Class D Audio Amplifier Created by Bill Earl Last updated on 2014-10-28 10:45:16 AM EDT Guide Contents Guide Contents Overview Specifications: What is a Class D Amplifier? Other Audio amps
More information1. Summary. 15/08/2009 Philips Valve Amplifier Type LBH1015/01 Page 1 of 7. Valve PA Amplifier. Philips label Model Code LBH1015/01 Serial No 1080
15/08/2009 Philips Valve Amplifier Type LBH1015/01 Page 1 of 7 1. Summary Valve PA Amplifier. Philips label Model Code LBH1015/01 Serial No 1080 Two input, mono 60W amplifier with tone control and 50V/70V/100V
More informationMPC-XU Universal Crossover
MPC-U Universal Crossover For JBL MPC and MPA amplifiers Owner s Manual and Installation Guide I. Description The MPC-U is a dual-channel universal crossover filter accessory for use with JBL MPC and MPA
More informationDual CV Source + Attenuator/Mixer
Dual CV Source + Attenuator/Mixer Model 9744 Assembly and Using Manual This second-generation 9700-series processing element for modular sound synthesizers is designed to provide great sound and excellent
More informationTEN-TEC Orion (Model 565 and 566) 9 MHz IF Output
TEN-TEC Orion (Model 565 and 566) 9 MHz IF Output Prepared by Rick Williams, VE7TK (Note: Those undertaking this modification do so at their own risk. The procedures outlined provided a 9 MHz IF output
More informationBuild Your Own Clone British Blues Overdrive Kit Instructions
Build Your Own Clone British Blues Overdrive Kit Instructions Warranty: BYOC, LLC guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free
More informationClassic Valve Design
DynaMull Driver Board for the Dynaco ST-70 Classic Valve Design Classic Valve Design assumes no responsibility for circuit or user damage from the use or misuse of these boards or any other product. We
More informationBuild an All-Tube Fuzz/Wah Pedal
Build an All-Tube Fuzz/Wah Pedal by Eric Barbour and Peter Belov In spite of more than 30 years of development and marketing, to this day all commercial guitar "wah" pedals have been solid- state and have
More informationDRTXM2 TRANSMITTER BILL OF MATERIAL IDENT QTY PART NUMBER DESCRIPTION
DRTXM2 TRANSMITTER BILL OF MATERIAL H1 C1-5,7,10-11,15,17-18,20, 22-28,34,38, 43-46,49-53,1A,2A 8 Right Angle LED Mount 0 0.01uf 50V Ceramic Disc Capacitor 31 0.1 UF/50V Decoupling Capacitors C13,14,39-42
More informationCX-A6 Amplifier Installation & User Guide V9.0
CX-A6 Amplifier Installation & User Guide V9.0 Cloud Electronics Limited 140 Staniforth Road, Sheffield, S9 3HF England Tel + 44 (0) 114 244 7051 Fax + 44 (0) 114 242 5462 E-mail info@cloud.co.uk Web site
More informationLED Field Strength Indicator Kit
LED Field Strength Indicator Kit Description The Field Strength Indicator kit from Qrpkits.com provides a visual way to monitor RF fields through the brightness of an LED. It will respond to RF fields
More informationDynaMutt Driver Board for the Dynaco ST-70
DynaMutt Driver Board for the Dynaco ST-70 Octal Version Design by: Classic Valve Design Classic Valve Design assumes no responsibility for circuit or user damage from the use or misuse of these boards
More informationIPR LA-3 KIT last update 15 march 06
IPR LA-3 KIT last update 15 march 06 PART-2: Audio Circuitry CIRCUIT BOARD LAYOUT: Power and Ground Distribution Now that your power supply is functional, it s time to think about how that power will be
More informationCircuit and wiring connections as follows:
Fault Indication via TTL compatible open collector output (can be used for additional protection circuitry or for our upcoming electronic choke PSU PCB) multiple mounting holes for easy mounting Can be
More informationSingle Tube Line Stage. Classic Valve Design for the Dynaco PAS2, PAS3, PAS3X. Classic Valve Design
Single Tube Line Stage by Classic Valve Design for the Dynaco PAS2, PAS3, PAS3X Classic Valve Design Classic Valve Design assumes no responsibility for circuit or user damage from the use or misuse of
More informationModification of the AM For 432 MHz
Modification of the AM6154-6155 For 432 MHz by Ron Whitsel, W3RJW Updated 1/18/04 It seems the modifications to the venerable Fair Radio FAA amps for use on 432 has been lost in space. Following are the
More informationStep 3. Remove the strings from your guitar.
VSTK-1 Vintage Stratocaster Kit Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers Electric Drill 3/16 Drill Bit 11/64
More informationSSB-MITE Assembly Manual. Copyright David Cripe NM0S The 4 State QRP Group. Introduction
SSB-MITE Assembly Manual Copyright 2017 David Cripe NM0S The 4 State QRP Group Introduction Thank you for purchasing a SSB-MITE. We hope you will enjoy building it and find it a useful addition to your
More informationMini Block Ultra Linear Class A Push-Pull Valve Power Amplifier
Mini Block Ultra Linear Class A Push-Pull Valve Power Amplifier Precaution: This project uses potentially lethal voltages and should not be undertaken by anyone who is not familiar with working with such
More informationOzark Patrol Assembly Manual
Ozark Patrol Assembly Manual Copyright 2014 David Cripe NM0S The 4 State QRP Group Thank you for purchasing a Ozark Patrol kit. We hope you will enjoy building it and and find it a fun addition to your
More informationCode Practice Oscillator (CPO) For kit building instructions turn to Page 3.
Code Practice Oscillator (CPO) For kit building instructions turn to Page 3. Overview Many thanks for your purchase of this code practice oscillator or CPO, this guide is intended to allow you to quickly
More informationNOTE: The relay coil is polarity sensitive
External QSK T/R Switch for HF Amplifiers Phil Salas AD5X Like many HF amplifiers, my Ameritron ALS-600 uses a power relay for T/R switching. The long 15-20ms enable/release time of this relay makes the
More informationBuild Your Own Clone The Swede Kit Instructions
Build Your Own Clone The Swede Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationTweed Champ 5F1 (assembling the board)
Tweed Champ 5F1 (assembling the board) The Beginning of Great Tone - In 1958, the Fender Champ with it's 8 speaker and 5 watts of power became the mother of great tone. By combining the new 12AX7 with
More informationNo crimping is required just solder the the wire to the crimp piece and use some heat shrink tubing to cover the end of the crimp.
In this section we will be wiring up the IEC socket (AC plug) with the rocker switch and the Mains transformer primaries. Follow these instructions if you live in an area with 100, 110, 220 or 230 Volts!"
More informationValue Location Qty Potentiometers C1M Distortion 1 A10k Volume 1. Footswitch 3PDT SW1 1. Jacks 1/4 Mono 2 DC Power 1
Distortion BUILD INSTRUCTIONS Thank you for your purchase of our Distortion+ kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same
More informationD ELCO. electronic parts AUTO RADIO BULLETIN. Connect Signal Generator to
D ELCO electronic parts AUTO RADIO BULLETIN Bulletin 6D-864 Date 10-15-56 Page 1 FIRST ISSUE SUBJECT: SERVICE INSTRUCTIONS - CHEVROLET CUSTOM DELUXE WITH PUSH BUTTON TUNING - MODEL 987575 GENERAL M O U
More informationSPACE WAR GUN KIT MODEL K-10. Assembly and Instruction Manual. Elenco Electronics, Inc.
SPACE WAR GUN KIT MODEL K-10 Assembly and Instruction Manual Elenco Electronics, Inc. Copyright 1989 Elenco Electronics, Inc. Revised 2001 REV-H 753210A PARTS LIST Contact Elenco Electronics (address/phone/e-mail
More informationBitx Version 3 Linear Amplifier Assembly
Bitx Version 3 Linear Amplifier Assembly The power supply section has 2 options. 1 - AC input and a higher voltage on the IRF510 and +12 volts to the bitx. 2 - +12 volts applied to both the final and the
More informationBRIDGEABLE FOUR-CHANNEL POWER AMPLIFIER GM-A6604 GM-A4604. Owner s Manual
BRIDGEABLE FOUR-CHANNEL POWER AMPLIFIER GM-A6604 GM-A4604 Owner s Manual Section 01 Before you start Thank you for purchasing this PIONEER product To ensure proper use, please read through this manual
More informationBuild Your Own Clone Silver Pony Kit Instructions
Build Your Own Clone Silver Pony Kit Instructions Warranty: BYOC, Inc. guarantees that your kit will be complete and that all parts and components will arrive as described, functioning and free of defect.
More informationAmphenol RF Interconnects BNC 31 Series Bayonet Lock RF Connector System
BNC 31 Series Bayonet Lock RF Connector System Materials Body/Finish /Nickel Centre MALE Centre FEMALE Phosphor Bronze Centre Finish Gold 30µ Insulator Delron/PBT Gasket Silicone Rubber Crimp s Annealed
More information