Residual Current Monitoring Unit RCMU101SN-4P16C
|
|
- Penelope Watson
- 5 years ago
- Views:
Transcription
1 Magtron Residual Current Monitoring Unit(RCMU ) Update: V1.0.3 Features Self-check function Single Supply +5 V Positive output for ADC Printed circuit board mounting Characteristics Stable accuracy self stimulation Low hysteresis offset voltage Short response time Integration frequency filter Compact design Applications Appliance ground fault detection Solar inverter residual current Converter leakage current detection UPS and other power ground fault detection Electric vehicle charge station Single or 3 Phases differential current detection Select Part List Part Number IPN(mA) IPM(mA) IM(A) ±1020 ±1700 ±80 Standards EN50178 IEC UL1741 VDE GBT / IEC / UL1449 Overview An important safety function of these devices is monitor of the leakage current of the entire system from Power modules or inverter against earth. A defective system can become dangerous for people or cause fires. Before it comes so far, the inverter must be disconnect from the grid. The leakage current contains DC and AC components. Therefore an AC/DC-sensitive monitoring unit is necessary. The heart of the safety device is the Magtron RCMU, whose value is evaluated by the control system of the Power inverter. Generally protection devices with AC/DC-sensitive differential current sensors can be used everywhere, where flat or pulsating DC can develop, whose amount is permanently greater than zero. Instruction of installation in a Pollution Degree 2 environment is available on the table below(or equivalent statement).
2 Application circuit Functional block diagram Application circuit Note: C1 should be close to the current sensor s pin Component selection reference: Designator Description C1 TDK,X5R,10uF/16V,±10%,0603 Pin Definition No. Symbol Description 1 VO Signal output 2 CHK Product Self-Check input 3 GND Power GND 4 VCC Power supply 5 REF Reference voltage output 6~13 IP Primary Current Current direction Assembly Pin Relationship between IP and output voltage
3 Absolute Maximum Ratings Parameter Symbol Min Typ Max Unit Supply Voltage(not operating) VC 5.5 V Ambient operating temperature TA Ambient storage temperature TA High Voltage Characteristics Parameter Symbol Value Unit Rms voltage for AC insulation test, 50 Hz, 1 min Ud 4.5 kv Impulse withstand voltage 1.2/50 μs Uw 7 kv System working voltage (RMS) Vs <750 V Comparative Tracking Index (group I) CTI 600 V Clearance (See drawing in page 6) DCI TBD mm Creepage distance (See drawing in page 6) DCP TBD mm Application example - 300, CAT III,PD2 V Application example - 600, CAT III, PD2 V Other Characteristics Parameter Symbol Value Unit Wave soldering profile TWSP 260 Electrical data At Ta=25,Vc=5V, unless otherwise noted Parameter Symbol Min Typ Max Unit Comment Power Supply voltage Vc V 2% Cureent consumption Ic 25 ma Primary differential cureent IPN ±1020 ma Measurement range IPM ±1700 ma Output static state voltage VOS 2.5 IP=0A Output voltage VON(+) IPN Output voltage VOM(+) IPM Output voltage VON(-) IPN Output voltage VOM(-) IPM Output voltage Gain VG Electrical offset voltage VOE <25 mv Accuracy X 2 IPN /25 Full temperature Accuracy XFT 4 IPN/-40~85 Linearity error εl 1 IPN Bandwidth BW 700 Check current ICK 170 ma 10% Output voltage (Check function) V(CK) VOS+0.2 V Check enable voltage VCE 3.3 Vc V Check disabled voltage VCD <0.2 V Reference Voltage VREF V 1% Fault over current recovery limit IM 80 A
4 Application information Self-check Function Set the CHK pin to high status. RCMU will run in self-test mode,check the out pin,equivalent to the status Ip equal Ick, at this time the output has equival voltage, the detector is OK.Then sets CHK to low voltage Vcheck<0.2V.The RCMU starts to run in the residual current. Photovoltaic Inverter Residual Current From VDE ,Inverters without a basic insulation (e.g. basic insulated transformer) between the grid and the photovoltaic-generator must have a fault current monitoring unit (RCMU)installed. The d.c. and a.c. component of the fault current depend on the construction of the inverter and on the d.c. voltage of the PV-generator.
5 PCB Footprint PCB Holes Secondary pins: ø1.1x2.2 Primary Pins: ø5.0x8.0 Top view Safety This transducer must be used in limited-energy secondary circuits according to IEC This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements inaccordance with the manufacturer s operating instructions. Caution, risk of electrical shock When operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply). Ignoring this warning can lead to injury and/or cause serious damage. This transducer is a build-in device, whose conducting parts must be inaccessible after installation. A protective housing or additional shield could be used. Main supply must be able to be disconnected.
6 Dimensions Mechanical Characteristics ( Unit : mm, Tolerance in ±0.2)
Residual Current Monitoring Unit RCMU101SN-4P16
Magtron Residual Current Monitoring Unit(RCMU ) Update: 2017.03.22. V1.0.3 Features +5V Supply Voltage Self-check function Positive output for ADC Printed circuit board mounting Characteristics Stable
More informationCurrent Transducer CTSR 1-P = 1A
Current Transducer CTSR 1-P I PRN = 1A For the electronic measurement of current: DC, AC, pulsed..., with galvanic isolation between the primary (high power) and the secondary circuit (electronic circuit).
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary circuit and the secondary circuit.
Current Transducer CTSR 0.6-TP/SP2 I PRN = 600 ma For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary circuit and the secondary circuit. Features
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit.
Current Transducer CASR series I PN = 6, 5, 25, 5 A Ref: CASR 6-NP, CASR 5-NP, CASR 25-NP, CASR 5-NP For the electronic measurement of current: DC, AC, pulsed..., with galvanic isolation between the primary
More informationHigh Performance Current Transducer IT 200-S ULTRASTAB = A. ε L
High Performance Current Transducer IT 200-S ULTRASTAB For the electronic measurement of currents: DC, AC, pulsed..., with galvanic isolation between the primary circuit and the secondary circuit. I PM
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer HO-NSM- SERIES I PN = 8, 15, 25 A Ref: HO 8-NSM-, HO 15-NSM-, HO 25-NSM- For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and
More informationRef: HLSR 10-P/SP3, HLSR 20-P/SP3, HLSR 40-P/SP3, HLSR 50-P/SP3
Current Transducer HLSR-P/SP3 series N = 10... 50 A Ref: HLSR 10-P/SP3, HLSR 20-P/SP3, HLSR 40-P/SP3, HLSR 50-P/SP3 For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer CAS 25-NP/SP2 N = 25 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Closed loop (compensated)
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer HO-NSM/SP33 series N = 8, 15, 25 A Ref: HO 8-NSM/SP33, HO 15-NSM/SP33, HO 25-NSM/SP33 For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current transducer CKSR series N = 6, 5, 25, 5 A Ref: CKSR 6-NP, CKSR 5-NP, CKSR 25-NP, CKSR 5-NP For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary
More information= 1000 V. Voltage transducer DVC 1000-P V P N
Voltage transducer DVC 1-P V P N = 1 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer ITL 4000-S I PN = 4000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. I > 0 P Features Closed
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer IN 1000-S N = 1000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Closed loop (compensated)
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current transducer LF 510-S I PN = 500 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated
More informationRef: HLSR 10-SM, HLSR 16-SM, HLSR 20-SM, HLSR 32-SM, HLSR 40-SM, HLSR 50-SM
Current Transducer HLSR-SM series N = 1... 5 A Ref: HLSR 1-SM, HLSR 16-SM, HLSR 2-SM, HLSR 32-SM, HLSR 4-SM, HLSR 5-SM For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation
More informationFor ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.
Current Transducer IT 700-S ULTRASTAB I PM = 700 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Closed loop (compensated)
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer ITL 4000-S I P N = 4000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. I > 0 P Features Closed
More informationRef: HLSR 10-SM/SP33, HLSR 20-SM/SP33, HLSR 32-SM/SP33, HLSR 40-P/SP33, HLSR 50-SM/SP33
Current Transducer HLSR-SM/SP33 series I PN = 10... 50 A Ref: HLSR 10-SM/SP33, HLSR 20-SM/SP33, HLSR 32-SM/SP33, HLSR 40-P/SP33, HLSR 50-SM/SP33 For the electronic measurement of current: DC, AC, pulsed...,
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer N = 6, 15, 25, 5 A Ref: LESR 6-NP, LESR 15-NP, LESR 25-NP, LESR 5-NP For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current transducer LF 510-S/SP13 I PN = 500 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and secondary circuit.
Current Transducer LF 510-S I P N = 500 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and secondary circuit. Features Bipolar and insulated
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer IN 1000-S I P N = 1000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Closed loop (compensated)
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer LF 2010-S/SPA7 I P N = 2000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current transducer LF 2010-S I PN = 2000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated
More informationFor ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.
Current Transducer IT 700-SB ULTRASTAB I PM = 700 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features ± 10 V voltage output
More informationFor ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.
Current Transducer ITN 1000-S ULTRASTAB I PM = 1000 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Closed loop (compensated)
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current transducer LF 210-S/SP3 I PN = 100 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer LF 1010-S/SPA5 I P N = 1000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer LF 2010-S/SPA0 I P N = 2000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and
More informationRef: HO 50-S/SP33, HO 100-S/SP33, HO 150-S/SP33, HO 200-S/SP33, HO 250-S/SP33
Current Transducer HO-S/SP33 series I PN = 50, 100, 150, 200, 250 A Ref: HO 50-S/SP33, HO 100-S/SP33, HO 150-S/SP33, HO 200-S/SP33, HO 250-S/SP33 For the electronic measurement of current: DC, AC, pulsed...,
More informationHigh Performance Current Transducer ITL 900-T = A
High Performance Current Transducer ITL 900-T For the electronic measurement of currents: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. I PM = 0... 900 A Electrical
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer LESR series N = 6, 15, 25, 5 A Ref: LESR 6-NP, LESR 15-NP, LESR 25-NP, LESR 5-NP For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer LF 21-S/SPA2 I P N = 2 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated
More informationThe four pin one (J1) makes possible to supply the board and access to the output voltage easily. It has the following pin-out:
User guide for FHS 40-P Current Transducer FHS 40-P Kit 9 (G2.00.23.108.0) Evaluation PCB Connectors Pin-OUT The board has two single row connectors J1 and J2. The four pin one (J1) makes possible to supply
More informationFor ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.
Current Transducer IT 605-S ULTRASTAB I PN = 600 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Wide operating temperature
More informationFor ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.
Current Transducer IT 200-S ULTRASTAB I PM = 200 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Closed loop (compensated)
More informationFor ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.
Current Transducer IT 205-S ULTRASTAB I PN = 200 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Wide operating temperature
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current transducer LF 1010-S/SPA2 I PN = 1000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and
More informationFor the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit.
Voltage transducer DVL 15 V PN = 15 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Features Bipolar and isolated
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer HO-NP series I PN = 4, 6, 12, 15 Ref: HO 4-NP, HO 6-NP, HO 12-NP, HO 15-NP For the electronic measurement of current: DC, C, pulsed..., with galvanic separation between the primary and
More informationVoltage transducer DVL 50
Voltage transducer DVL 5 V PN = 5 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Features Bipolar and isolated measurement
More informationFor the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit.
Voltage transducer V PN = 1 V Ref: DV 1/SP For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Features Bipolar and isolated
More informationV P N. Voltage transducer DVM 2000-B = 2000 V
Voltage transducer DVM 2-B V P N = 2 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated
More informationFor the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit.
Voltage transducer V PN = 4 V Ref: DV 4/SP4 For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic isolation between the primary and the secondary circuit. Features Bipolar and isolated
More informationHO 50-S/SP30, HO 100-S/SP30, HO 150-S/SP30, HO 200-S/SP30, HO 250-S/SP30 and HO 200-S/SP31
Current Transducer HO-S/SP3 series Ref: I PN = 5,, 15, 2, 25 A HO 5-S/SP3, HO -S/SP3, HO 15-S/SP3, HO 2-S/SP3, HO 25-S/SP3 For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation
More informationFor the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Voltage transducer DV 42/SP3 V P N = 42 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated
More informationI PN. Ref: HO 50-S, HO 100-S, HO 150-S, HO 200-S, HO 240-S, HO 250-S
Current Transducer HO-S series I PN = 50, 100, 150, 200, 240, 250 A Ref: HO 50-S, HO 100-S, HO 150-S, HO 200-S, HO 240-S, HO 250-S For the electronic measurement of current: DC, AC, pulsed..., with galvanic
More informationCurrent Sensor : F02P***S05L
Features: Backward compatible to F02PS***05 series Anti-Surge current (4kAT, 8/20uS, single) Mounting area reduced ; pin compatible. Longitudinal dimension reduced Super precision & High Stability (low
More informationFor the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Voltage transducer DV 64 V P N = 64 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated
More informationV P N. Voltage transducer DVM 4200 = 4200 V
Voltage transducer DVM 42 N = 42 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated measurement
More informationFor the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Voltage transducer DV V PN = V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Applications Bipolar and insulated
More informationI P. /dt. di p V S Applications. Standards 1) IEC : 2007; IEC : ) IEC : 2016; IEC : 2017
Ref: ART-B22-D70, ART-B22-D125, ART-B22-D175, ART-B22-D300 Flexible clip-around Rogowski coil for the electronic measurement of AC current with galvanic separation between the primary circuit (power) and
More informationI P I OUT R L. Applications. Standards. N 52.D ; Page 1/8
Ref: ATO-10-B225-D10/SP3 r = 10 A ATO series is a split core current transformer for the electronic measurement of AC waveform current with galvanic separation between the primary circuit (power) and the
More informationI P. /dt. di p V S+ Applications. Standards. 1) IEC ed1.0: 2007; IEC : ed1.0: 2012
Ref: ART-B22-D70, ART-B22-D125, ART-B22-D175 Flexible clip-around Rogowski coil for the electronic measurement of AC current with galvanic separation between the primary circuit (power) and the secondary
More informationV P N. Voltage transducer DVL 1000 = 1000 V
Voltage transducer DVL 1 V P N = 1 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated
More informationUnipolar voltage - Current output 4-20 ma Ref: DVL 50-UI, DVL 150-UI, DVL 250-UI, DVL 500-UI, DVL 750-UI, DVL 1000-UI, DVL 1500-UI
Current Transducer DVL-UI series V PN = 50... 1500 V Unipolar voltage - Current output 4-0 ma Ref: DVL 50-UI, DVL 150-UI, DVL 50-UI, DVL 500-UI, DVL 750-UI, DVL 1000-UI, DVL 1500-UI For the electronic
More informationI Pr I P I OUT R L. Applications. Standards
Ref: ATO-XXX-B225-D10 I Pr = 10, 15, 16, 20, 30, 32, 50, 60, 63, 75 A ATO series is a split core current transformer for the electronic measurement of AC waveform current with galvanic separation between
More information= 600 V. Voltage transducer DVM 600 V PN
Voltage transducer DVM 6 V PN = 6 V For the electronic measurement of voltage: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated
More informationFor the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current transducer ITC 2000-S/SP2 N = 2000 A For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. Features Bipolar and insulated
More informationDS200ID-CD100. Specification highlights Symbol Unit Min Typ Max. Features. Applications: Linearity error maximum 2 ppm. MPS for particles accelerators
Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 370A Features Linearity error maximum 2 ppm 100
More informationDS400ID. Specification highlights Symbol Unit Min Typ Max. Features. Applications: Linearity error maximum 1.5 ppm. MPS for particles accelerators
Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 600A Features Linearity error maximum 1.5 ppm Fluxgate,
More informationDS2000UBLA-10V. Features. Applications: 20 ppm linearity. MPS for particles accelerators. 15 ppm offset. Gradient amplifiers for MRI devices
Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 2000A Features 20 ppm linearity 15 ppm offset 10V
More informationDM1200ID. Specification highlights Symbol Unit Min Typ Max. Applications: Features. Power measurement and power analysis
Ultra-stable, high precision (ppm class) fluxgate technology DM Series current transducer for non-intrusive, isolated DC and AC current measurement up to 1500A Features Ø45mm aperture enabling large isolated
More informationDL2000ID. Specification highlights Symbol Unit Min Typ Max. Features. Applications: 1 ppm linearity. MPS for particles accelerators.
DL000ID Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 3000A Features ppm linearity 6 ppm offset
More informationDQ600ID. Specification highlights Symbol Unit Min Typ Max. Features. Applications: Linearity error maximum 1 ppm. MPS for particles accelerators
Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 1000A Features Linearity error maximum 1 ppm Fluxgate,
More informationDS10000ULFS-10V/10kA
Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 11kA Features Linearity error maximum +/- 7ppm
More informationSPECIFICATION Item no.: T60404-N4646-X975
Customer: Standard type Customers Part no.: Page 1 of 2 8Description Characteristics Applications Closed loop (compensation) Excellent accuracy Mainly used for stationary operation in industrial Current
More informationDS2000ICLA. Specification highlights Symbol Unit Min Typ Max. Features. Applications: 1 ppm linearity. MPS for particles accelerators.
Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 3000A Features ppm linearity 0 ppm offset Current
More informationFluxgate system / Voltage-output type F03P***S05 SERIES
Fluxgate system / Voltage-output type F03P***S05 SERIES rev A / May 2013 ABSOLUTE MAXIMUM RATGS Parameters Symbol Unit Value Comment Supply voltage Primary conductor temperature Non repetitive primary
More informationAUTOMOTIVE CURRENT TRANSDUCER HC2F100-SN CLIPS
AUTOMOTIVE CURRENT TRANSDUCER HCF-SN CLIPS Introduction The HCF CLIPS Family is for the electronic measurement of DC, AC or pulsed currents in high power and low voltage automotive applications with galvanic
More informationSPECIFICATION Item no.: T60404-N4646-X764
Customer: Standard type Customers Part no: Page 1 of 4 Description Closed loop (compensation) Current Sensor with magnetic field probe Printed circuit board mounting Casing and materials UL-listed Electrical
More informationI PM. Current Transducer ITZ 5000-SB FLEX ULTRASTAB = 5000 A
urrent Transducer ITZ 5000-SB FLEX ULTRASTAB I PM = 5000 A For ultra-high precision measurement of current: D, A, pulsed..., with galvanic separation between primary and secondary. Separate magnetic head
More informationAUTOMOTIVE CURRENT TRANSDUCER HAH3DR 700-S00
AUTOMOTIVE CURRENT TRANSDUCER HAH3DR 700-S00 Introduction The HAH3DR family, a tri-phase tranducer is for the electronic measurement of DC, AC or pulsed s in high power automotive applications with galvanic
More informationCMS2005 MagnetoResistive Current Sensor (I PN
The CMS2000 current sensor family is designed for highly dynamic electronic measurement of DC, AC, pulsed and mixed currents with integrated galvanic isolation. The MagnetoResistive technology enables
More informationAC/DC-sensitive Differential Current Sensors (DI-Sensors)
AC/DC-sensitive Differential Current Sensors (DI-Sensors) Closed loop sensors with magnetic probe for highest accuracy and reliability Differential range typically 30 to 300 ma Full load to 50 A Single
More informationCMS2050 MagnetoResistive Current Sensor (I PN
The CMS2000 current sensor family is designed for highly dynamic electronic measurement of DC, AC, pulsed and mixed currents with integrated galvanic isolation. The MagnetoResistivetechnology enables an
More informationAUTOMOTIVE CURRENT TRANSDUCER HC6F600-S
AUTOMOTIVE CURRENT TRANSDUCER HC6F600-S 18198102215 Page 1/5 Introduction Principle of HC6F Family The HC6F Family is for use on the electronic measurement of DC, AC or pulsed currents in high power and
More informationAUTOMOTIVE CURRENT TRANSDUCER HAH3DR 700-S02
AUTOMOTIVE CURRENT TRANSDUCER Introduction The HAH3DR family, a tri-phase tranducer is for the electronic measurement of DC, AC or pulsed s in high power automotive applications with galvanic isolation
More informationCustomer: Standard type Page 1 of 7 Description Fluxgate current sensor with toroidal core PCB mounting
Customer: Standard type Page 1 of 7 Description Fluxgate current sensor with toroidal core PCB mounting Electrical data Ratings min. typ. max. Unit I P Primary nominal RMS current (1phase / 3phase) 80
More informationAUTOMOTIVE CURRENT TRANSDUCER HC6F700-S
AUTOMOTIVE CURRENT TRANSDUCER HC6F700-S 18198102215 Page 1/5 Introduction Principle of HC6F Family The HC6F Family is for use on the electronic measurement of DC, AC or pulsed currents in high power and
More informationLinear Current Sensor with differential outputs
Linear Current Sensor with differential outputs Features: 4Xmm current conductor through hole Output voltage proportional to AC and DC current Built-in AC to DC rectifier circuit Wide sensing current range
More informationAUTOMOTIVE CURRENT TRANSDUCER HC6H1000-S
AUTOMOTIVE CURRENT TRANSDUCER HC6H1000-S 18198151434 Page 1/ 5 HC6H1000-S Introduction Principle of HC6H Family The HC6H Family is for use on the electronic measurement of DC, AC or pulsed currents in
More informationV1000-ISO ± 1000V PRECISION HIGH BANDWIDTH ISOLATED VOLTAGE TRANSDUCER
KV rms Isolation ltage Divider ± V PRECISION HIGH BANDWIDTH VISO FEATURES ltage Measuring Range: to ± V Output ltage Range: to ± V Both AC and DC ltage Measurement Galvanic Isolated ltage Rating: Vrms
More informationCustomer: Standard type Page 1 of 7 Description Fluxgate current sensor with toroidal core PCB mounting
Customer: Standard type Page 1 of 7 Description Fluxgate current sensor with toroidal core PCB mounting Characteristics Excellent accuracy AEC-Q qualified components Switching open-collector outputs Compact
More informationAUTOMOTIVE CURRENT SENSOR HC6H300-S
AUTOMOTIVE CURRENT SENSOR HC6H300-S Page 1/ 5 Introduction Principle of HC6H Family The HC6H Family is for use on the electronic measurement of DC, AC or pulsed currents in high power and low voltage automotive
More informationAUTOMOTIVE CURRENT SENSOR HC6H500-S. Datasheet
AUTOMOTIVE CURRENT SENSOR HC6H500-S Datasheet Page 1/ 5 Introduction Principle of HC6H Family The HC6H Family is for use on the electronic measurement of DC, AC or pulsed currents in high power and low
More informationHCPL-7840 Isolation Amplifier
Products > Optocouplers - Plastic > Plastic Miniature Isolation Amplifier > HCPL-7840 HCPL-7840 Isolation Amplifier Description The HCPL-7840 isolation amplifier family was designed for current sensing
More informationCDS4025 MagnetoResistive Current Sensor (I PN
The CDS4000 current sensor family is designed for highly dynamic electronic measurement of DC, AC, pulsed and mixed currents with integrated galvanic isolation. The MagnetoResistive technology enables
More informationClassification Contact form Enclosure rating Terminal shapes Model Minimum packing unit Standard. SPST-NO (1a) Fully sealed PCB terminal
SPST Slim Power Relay for A switching Slim -mm width and miniature size. (20.08 12. mm) High switching capability A (20 VAC and VDC), and high contact reliability by crossbar-twin contact. Low power consumption
More informationCMS3050 Highly Dynamic MagnetoResistive Current Sensor (I PN
Highly Dynamic MagnetoResistive Current Sensor (I PN Data ShEEt The CMS3000 current sensor family is designed for highly dynamic electronic measurement of DC, AC, pulsed and mixed currents with integrated
More informationAC/DC sensitive residual current monitoring module RCMB121-
AC/DC sensitive residual current monitoring module RCMB121- for safe charging of electrical vehicles according to IEC 62752 for IC-CPD and IEC 60364-7-722 for Wall Boxes Preliminary datasheet Vorläufiges
More informationHCPL-7800 Isolation Amplifier
Products > Optocouplers - Plastic > Plastic Miniature Isolation Amplifier > HCPL-7800 HCPL-7800 Isolation Amplifier Description The HCPL-7800 isolation amplifier family was designed for current sensing
More informationDifferential Current Sensor acc. to the standard UL2231 Ed.2.0. Customer: Standard type Page 1 of 7. Electrical data Ratings min. typ. max.
Customer: Standard type Page 1 of 7 Electrical data Ratings min. typ. max. Unit I P Primary nominal RMS current (1phase / 3phase) 32 40 A I N1 Rated residual operating current 1 5 ma rms I N2 Rated residual
More informationClassification Terminal Shape Contact form Enclosure rating Model Rated coil voltage
ow-profile Relay with Various Models ow profile:.7 mm in height. Creepage distance 8mm between coil and contacts 0 kv Impulse withstand voltage Models with AC coil available. High-Inrush model available
More informationAUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY HAH3DR 1100-S07
AUTOMOTIVE CURRENT TRANSDUCER OPEN LOOP TECHNOLOGY Introduction The HAH3DR-S07 family is a tri-phase transducer for DC, AC, or pulsed currents measurement in automotive applications. It offers a galvanic
More informationSPECIFICATION Item no.: T60404-N4646-X651
VACUUMSCHMELZE SPECIFICATION Item no: T60404-N4646-X651 K-no: 24507 25 A Current Sensor modul for 5V-supply voltage Date: 10122010 For electronic current measurement: DC, AC, pulsed, mixed, with a galvanic
More informationSPST-NO SPDT DPST-NO DPDT
PCB Relay A Power Relay with Various Models High-sensitivity ( mw) and High-capacity ( A) Models available. Low profile:.7 mm max. in height Conforms to VDE (EN0-), UL and CSA.. Meets EN0- requirements
More informationSPECIFICATION Item no.: T60404-N4646-X762
V A C U U M S C H M E L Z E SPECIFICATION Item no: T60404-N4646-X762 K-no: 26020 15 A Current Sensor for 5V- Supply Voltage Date: 03072012 For electronic current measurement: DC, AC, pulsed, mixed, with
More informationOPTICALLY ISOLATED ERROR AMPLIFIER FOD2711 DESCRIPTION FEATURES APPLICATIONS PIN DEFINITIONS 9/6/02
DESCRIPTION The Optically Isolated Amplifier consists of the popular RC4A precision programmable shunt reference and an optocoupler. The optocoupler is a gallium arsenide (GaAs) light emitting diode optically
More informationAC/DC sensitive residual current monitoring module RCMB121-
AC/DC sensitive residual current monitoring module RCMB121- for safe charging of electrical vehicles according to IEC 62752 for IC-CPD and IEC 60364-7-722 for Wall Boxes Vorläufiges Datenblatt RCMB121_D00267_01_D_XXEN/05.2018
More information