SPECIAL SPECIFICATION 6609 Fiber Optic Color Video and Data Transmission Equipment
|
|
- Audrey Oliver
- 5 years ago
- Views:
Transcription
1 1995 Metric CSJ's & SPECIAL SPECIFICATION 6609 Fiber Optic Color Video and Data Transmission Equipment 1. Description. This Item shall govern for the furnishing and installation of Fiber Optic Color Video and Data Transmission Equipment (FO-TE) in field location(s) as shown on the plans and as detailed in the Special Specifications. 2. Material. (1) General Requirements. All materials furnished, assembled, fabricated, or installed under this Item shall be new, corrosion resistant and in strict accordance with the details shown on the plans and in the specifications. The FO-TE shall consist of (a) fiber optic color video and data transmitter, and (b) fiber optic color video and data receiver. The fiber optic color video and data transmitter shall consist of video transmitter and data transceiver. The fiber optic color video and data receiver shall consist of video receiver and data transceiver. (2) Functional Requirements. The FO-TE shall be able to communicate its simplex video signal, and full duplex digital camera control data signals simultaneously over a single optical fiber between specified locations as shown in the plans as detailed in the specifications, and as directed by the Engineer. The video shall be transmitted in real time with a camera-to-monitor video bandwidth of at least 8 MHz. The data input/output circuits shall support two-way RS-232. The FO-TE operating optical wave lengths for each direction shall be 1300 nm (singlemode) for video and camera control data. One (1) video/data link (1 singlemode fiber) will be required for each camera in the field. Each link shall meet EIA/TIA Standard 250C medium haul video requirements. Both the fiber optic color video, and data transmitter and receiver of the FO-TE shall be from the same manufacturer. (3) Electrical/Optical Requirements. (a) Transmitter Video Input. Transmitter Video Input shall be 75 Ohms nominal, 1.0 Volt peak-to-peak between sync tip, and 100% white level in accordance with EIA/TIA Standard 250C. (b) Transmitting Device. The transmitting device shall be capable of transmitting over a singlemode fiber strand
2 (c) Transmitter Optical Output. Output power to 8/125 singlemode (step index) dual window-glass fiber, as indicated on the plans, at wave lengths of 1300 nm/1550 nm shall be sufficient to accommodate a link loss budget of 13 db at 1300 nm. Once the design is tested and approved, the optical coupled power value and tolerance will become incorporated as part of this specification for the purpose of acceptance tests. (d) Optical Detector. The optical detector of the receiver shall be a Pin diode. (e) Receiver Optical Input. Receiver input shall have a minimum sensitivity of 13 db at 1300 nm below the transmitter output level and operate within the parameters of this specification. Once the design is tested and approved, the receiver sensitivity value and tolerance shall be incorporated as a part of this specification for the purpose of acceptance tests. (f) Receiver Automatic Gain Control. The receiver shall have automatic gain control (AGC) circuitry to provide the receiver with the required dynamic range from transmitter-receiver spacing of 0 to 13 db at 1300 nm. The above dynamic range requirements may be accomplished with external optical attenuators with the approval of the Engineer. (g) Receiver Video Output. Receiver Video Output shall be 75 Ohms nominal, 1.0 Volt peak-to-peak between sync tip, and 100% white-level in accordance with EIA/TIA Standard 250C. (h) Transmitting/Receiving Devices. The transmitting and/or receiving devices shall have a minimum, mean time, between failure (MTBF) of 100,000 hours at 50 C ambient. The devices shall incorporate diagnostic bi-color video input LEDs in the transmitter and bi-color level/loss indicators in the receiver for quick visual indication of link operation. (i) Modulation. Modulation shall be pulse frequency modulation. (j) Signal to Noise Ratio. The system signal to noise ratio (SNR), measured as peak-to-peak white to blanking, to rms noise (ppwb/rms) in a 10 KHz to 5 MHz bandwidth shall be better than 60 db. (k) Linearity. Linearity shall be better than 1 percent. (l) Tilt. Tilt shall be less than 2 percent. (m) Differential Phase. Differential Phase shall be less than 1.4 degrees for a 10 percent to 90 percent average picture-level (APL)
3 (n) Differential Gain. Differential Gain shall be less than 5 IRE or % for a 10 percent to 90 percent average picture-level (APL). (o) Frequency Response. Frequency Response shall be plus or minus 0.2 db, 10 Hz to 0.5 MHz; plus or minus 0.5 db, 0.5 MHz to 4.2 MHz. (p) Optical Fiber Compatibility. Optical Fiber Compatibility shall be 8/125 micron, dual-window singlemode glass fiber, as indicated on the plans. (q) Data Performance Requirements. Digital data transmitted and received by the FO-TE shall conform to all the requirements of EIA Standard RS-232. (r) Data Rate. The FO-TE shall support data transmission rates from 0 bits/sec up to and including 9600 bits/sec. (s) Bit Error Rate (BER). The bit error rate of each data channel shall not exceed 10 to the -9 power. (t) Power Requirements. Transmitters and Receivers shall operate at 12 to 16 VAC from a separate power supply to be provided as part of this bid item and shall not draw more than 10 watts of power each. The separate power supply shall operate from 115 VAC plus or minus 10%, and 60 Hz plus or minus 3 Hz. The equipment operation shall not be affected by the transient voltages, surges and sags normally experienced on commercial power lines. It is the Contractor's responsibility to check the local power service to determine if any special design is needed for the equipment. The extra cost, if required, shall be included in the bid of this Item. (u) Surge Protection. Appropriate surge protectors shall be installed in the cabinet for the co-axial cable connection to the video camera. (v) Power Service Transients. The equipment shall meet the requirements of Sec , "Transients, Power Service", of the NEMA Standard TS2-1992, and/or the latest revision. (w) Wiring. All wiring shall meet the requirements of the National Electrical Code. All wires shall be cut to proper length. Cable slacks shall be provided to facilitate removal and replacement of assemblies, panels, and modules. No wire shall be doubled back to take up slack. Wires shall be neatly laced into the cable with nylon lacing or plastic straps. Cables shall be secured with clamps. (x) Transient Suppression. All DC relays, solenoids, and holding coils shall have diodes or other protective devices across the coils for transient suppression. (y) Power Service Protection. The equipment shall contain readily accessible, manually resettable or replaceable circuit protection devices (such as circuit breakers or fuses) for equipment and power source protection
4 (z) Fail Safe Provision. The equipment shall be designed as such that the failures of the equipment shall not cause the failure of any other unit of equipment. (4) Mechanical Requirements. (a) Modular Design. The equipment shall be modular in design to allow major portions to be readily replaced in the field. Modules of unlike functions shall be mechanically keyed to prevent insertion into the wrong socket or connector. All modules and assemblies shall be clearly identified with name, model number, serial number, and any other pertinent information required to facilitate equipment maintenance. (b) Connectors and Harnesses. All external connections shall be made by means of connectors. The connectors shall be keyed to preclude improper hookups. All wires to and from the connectors shall be color coded and/or appropriately marked. Video input and output connectors shall be BNC type. Each and every conductive contact surface or pin shall be plated with no less than 20 microns of gold. Digital data inputs and outputs to and from the transmitter and receiver shall both be via a screw terminal type or DB type connector configured in a format compatible with the interface requirements of the data communications equipment attached. Connecting harness of appropriate length and terminated with matching connectors shall be provided for interconnection with the video cameras, camera control equipment, and the terminal equipment shown in the plans or as directed by the Engineer. (c) Housing. The transmitter and receiver shall be available in the standard compact serviceable modules. Dimensions of the transmitter or receiver module each shall not exceed 100 mm D x 180 mm W x 50 mm H. (5) Environmental Design Requirements. The equipment shall meet all of its specified requirements during and after subjecting to any combination of the following requirements: - Ambient temperature range of -17 C to 70 C. - Relative humidity from 0% to 95%. 3. Construction Methods. (1) General. The equipment design and construction shall utilize the latest available techniques with a minimum number of parts, subassemblies, circuits, cards, and modules to maximize standardization and commonality
5 The equipment shall be designed for ease of maintenance. All component parts shall be readily accessible for inspection and maintenance. Test points shall be provided for checking essential voltages and waveforms. (2) Electronic Components. All electronic components shall comply with Special Specification, "Electronic Components". (3) Mechanical Components. All external screws, nuts, and locking washers shall be stainless steel. No self-tapping screws shall be used unless approved by the Engineer. All parts shall be made of corrosion resistant material, such as plastic, stainless steel, anodized aluminum, or brass. All materials used in construction shall be protected from fungus growth and moisture deterioration. Dissimilar metals shall be separated by an inert dielectric material. 4. Documentation Requirements. The documentation requirements shall be in accordance with the Special Specification, "Testing, Training, Documentation, Final Acceptance and Warranty", Section Testing. The testing shall be in accordance with the Special Specification, "Testing, Training, Documentation, Final Acceptance and Warranty", Sections 2.(1)-(6). Testing shall also include the following: (1) Subsystem Test. The Contractor shall conduct a video transmission subsystem test. The test shall, at a minimum, demonstrate all video signal receptions in the control center location(s). A signal to noise ratio (SNR) test shall be conducted on all video links. The ratio shall meet the requirements in Section 2(3)(j) of this specification. If subsystem tests fail because of any component(s) in the subsystem, the particular component(s) shall be corrected or substituted with other component(s) and the tests shall be repeated. If a component has been modified as a result of the subsystem test failure, a report shall be prepared and delivered to the Engineer prior to re-testing. (2) Data Performance Tests. Digital data performance testing shall include all tests necessary to ensure compliance with all of the requirements of EIA Standard 232. These tests shall, at a minimum, demonstrate data communications between each of the data channel units in the control center and the corresponding data channel unit in the field. Using a loopback plug at each EIA-232 channel terminating at a field location, a 24-hour bit error rate test (BERT) for each channel shall be conducted using a data communications test set in the control center. This BERT is used to determine the bit error rate (BER) through the system and terminating equipment at each end, and to
6 certify that the EIA-232 channels can operate at a sustained rate of 9600 bits per sec (bps) for a 24-hour period. The 511-bit CCITT standard pseudo-random pattern shall be used for testing. The BER measured at 9600 bps shall not exceed the requirements of Section 2(3)(s) of this specification, and the error-free seconds (EFS) shall be better than 99.98%. If this BER is exceeded on any channel, the problem shall be corrected and the entire BERT shall be completely restarted from the beginning, as if no previous BERT had been conducted. If a component has been modified as a result of the subsystem test failure, a report shall be prepared and delivered to the Engineer prior to testing. 6. References. The FO-TE Supplier shall submit three (3) references, preferably State Departments of Transportation, that have been successfully operating a video and data transmission system supplied by this supplier, for a period of no less than one year. Reference data shall include name and address of organization, and the name and telephone number of an individual from the organization who can be contacted to verify system. 7. Training. The training shall be in accordance with Special Specification, "Testing, Training, Documentation Final Acceptance and Warranty.", Section Warranty. The warranty shall be in accordance with the Special Specification, "Testing, Training, Documentation, Final Acceptance and Warranty", Section Measurement. The Fiber Optic Color Video and Data Transmitter and Receiver will be measured as each unit furnished, installed, made fully operational and tested in accordance with these Special Specifications or as directed by the Engineer. 10. Payment. The work performed and material furnished in accordance with this Item and measured as provided under "Measurement" will be paid for at the unit prices bid for Fiber Optic Video Transmitter W/Data" or "Fiber Optic Video Receiver W/Data(Rack)". These prices will include all equipment described under this Item with all cables and connectors, all documentation and testing; and shall include the cost of furnishing all labor, materials, training, warranty and equipment necessary to complete the work
SPECIAL SPECIFICATION 6419 Fiber Optic Video Transceiver with Data
2004 Specifications CSJ 0617-01-169 SPECIAL SPECIFICATION 6419 Fiber Optic Video Transceiver with Data 1. Description. This Item shall govern for the furnishing and installation of Video optical transceiver
More informationSPECIAL SPECIFICATION 1789 Fiber Optic RS-232 Data Modem
1993 Specifications CSJ 2266-02-095 SPECIAL SPECIFICATION 1789 Fiber Optic RS-232 Data Modem 1. Description. This Item shall govern for the furnishing and installation of Fiber Optic RS- 232 Data Modem
More information1995 Metric CSJ SPECIAL SPECIFICATION ITEM Multimode Video Fiber Optic Transmission Equipment
1995 Metric CSJ 3483-01-010 SPECIAL SPECIFICATION ITEM 6329 Multimode Video Fiber Optic Transmission Equipment 1.0 Description. This Item shall govern for the furnishing and installation of Video Fiber
More informationSPECIAL SPECIFICATION 6734 RS-232 Optical Modem
2004 Specifications CSJ 0924-06-244 SPECIAL SPECIFICATION 6734 RS-232 Optical Modem 1. Description. This Item shall govern for the furnishing and installation of Fiber Optic RS- 232 Data Modem (OTR) in
More informationSPECIAL SPECIFICATION 1118 Data Fiber Optic Transceiver
2004 Specifications CSJ 0050-09-071, 0027-13-205, 0271-14-228, 0500-03-042, 0050-09-070, 0050-09-069 etc, 0050-08-086, 0050-08-087 & 0500-03-577 SPECIAL SPECIFICATION 1118 Data Fiber Optic Transceiver
More information1993 Specifications CSJ SPECIAL SPECIFICATION ITEM Drop/Insert Multiplexor/Demultiplexor
1993 Specifications CSJ 0008-12-071 SPECIAL SPECIFICATION ITEM 6550 Drop/Insert Multiplexor/Demultiplexor 1.0 Description. This Item shall govern for the furnishing and installation of intelligent drop/insert
More information1995 Metric CSJ SPECIAL SPECIFICATION ITEM Drop/Insert Multiplexor/Demultiplexor
1995 Metric CSJ 3256-02-049 1.0 Description SPECIAL SPECIFICATION ITEM 6093 Drop/Insert Multiplexor/Demultiplexor This Item shall govern for the furnishing and installation of intelligent drop/insert multiplexor/demultiplexors
More information1995 Metric CSJ SPECIAL SPECIFICATION ITEM Add/Drop Multiplexor/Demultiplexor
1995 Metric CSJ 0113-13-109 SPECIAL SPECIFICATION ITEM 6225 Add/Drop Multiplexor/Demultiplexor 1.0 Description. This Item shall govern for the furnishing and installation of intelligent Add/Drop Multiplexor/Demultiplexor
More informationSPECIAL SPECIFICATION 1533 Drop/Insert Multiplexor/Demultiplexor
1993 Specifications CSJ 0177-11-131 SPECIAL SPECIFICATION 1533 Drop/Insert Multiplexor/Demultiplexor 1. Description. This Item shall govern for for the furnishing and installation of intelligent drop/insert
More informationSPECIAL SPECIFICATION 1806 Spread Spectrum Wireless Modem
1993 Specifications CSJ s 0902-48-442 & 0902-48-432 SPECIAL SPECIFICATION 1806 Spread Spectrum Wireless Modem 1. General. This Item shall govern for the furnishing and installation of Spread Spectrum Wireless
More information1995 Metric CSJ , etc. SPECIAL SPECIFICATION ITEM D-I Muldem (Drop/Insert Multiplexor/Demultiplexor)
1995 Metric CSJ 0924-06-156, etc. SPECIAL SPECIFICATION ITEM 6588 D-I Muldem (Drop/Insert Multiplexor/Demultiplexor) 1. Description. This Item shall govern for the furnishing and installation of intelligent
More informationSPECIAL SPECIFICATION 8590 Emergency Vehicle Traffic Signal Priority Control System
2004 Specifications CSJ 0002-01-074, etc. SPECIAL SPECIFICATION 8590 Emergency Vehicle Traffic Signal Priority Control System 1. Description. This Item governs the furnishing and installation of emergency
More informationSPECIAL SPECIFICATION 8340 Dual Band Wireless Ethernet Radios
2004 Specifications CSJ 0914-00-280 SPECIAL SPECIFICATION 8340 Dual Band Wireless Ethernet Radios 1. Description. Furnish and install Dual Band Wireless Ethernet Radios (DBWERs) links for point-to-point
More informationSPECIAL SPECIFICATION 6574 Low Power Wireless Modem
2004 Specifications CSJ 1068-04-126, etc. SPECIAL SPECIFICATION 6574 Low Power Wireless Modem 1. Description. This work shall consist of furnishing and supplying a Low Power Wireless Modem at the locations
More informationThis Special Provision covers the requirements for the installation and testing of fibre optic modems (FOM).
FIBRE OPTIC MODEMS - Item No. Special Provision No. 683S09 September 2007 1. SCOPE This Special Provision covers the requirements for the installation and testing of fibre optic modems (FOM). 2. REFERENCES
More informationThis special provision is for the installation and testing of the following equipment:
FIBRE OPTIC MODEMS - Item No. Special Provision No. 683F18 April 2005 1. DESCRIPTION This special provision is for the installation and testing of the following equipment: Low Range Fibre Optic Modems
More informationLIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING
LIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING 1.0 General This specification covers the electrical characteristics and general
More information2.2 American National Standards Institute Corporation and its applicable standards C39.1, C80.1, C89, C84.1.
TECHNICAL SPECIFICATIONS for Single Phase, 1 to 3 KVA Power Conditioner with Regulation and Distribution Constant Power 3 (CP3) CP36508A 7/15/04 1.0 General This specification covers the electrical characteristics
More informationSPECIAL SPECIFICATION 6004 Digital Card Rack Inductive Loop Detector Assembly
2004 Specifications SPECIAL SPECIFICATION 6004 Digital Card Rack Inductive Loop Detector Assembly 1. Description. Furnish and install a digital card rack inductive loop detector assemblies. 2. Materials.
More informationWAVEFORM CORRECTOR (WAVEFORM CORRECTORS) REPLACES SURGE PROTECTION DEVICES (SPD) PREVIOUSLY KNOWN AS (TVSS)
WAVEFORM CORRECTOR (WAVEFORM CORRECTORS) REPLACES SURGE PROTECTION DEVICES (SPD) PREVIOUSLY KNOWN AS (TVSS) 1 PART 1: GENERAL This section describes materials and installation requirements for low voltage
More informationMICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR WIRELESS INTERCONNECT FOR SIGN MOUNTED FLASHER
MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR WIRELESS INTERCONNECT FOR SIGN MOUNTED FLASHER OPR:DJA 1 of 5 C&T:APPR:JAR:DBP:09-01-11 FHWA:APPR:09-01-11 a. Description. This work consists
More informationSPECIAL SPECIFICATION 6744 Spread Spectrum Radio
2004 Specifications CSJ 0924-06-244 SPECIAL SPECIFICATION 6744 Spread Spectrum Radio 1. Description. Furnish and install spread spectrum radio system. 2. Materials. Supply complete manufacturer specifications
More informationF290X / F293X FOM II Series Fiber Optic Isolator Technical Manual
F290X / F293X FOM II Series Fiber Optic Isolator Technical Manual Revision G Copyright 2017 VERSITRON, Inc. 83 Albe Drive / Suite C Newark, DE 19702 www.versitron.com E031130243 PROPRIETARY DATA All data
More informationInstruction Manual MT-945SL Four Channel Video Transmitter With Two Bi-Directional Data Channels
Instruction Manual MT-945SL Four Channel Video Transmitter With Two Bi-Directional Data Channels Copyright 2006, American Fibertek, Inc. 0307JD Table of Contents Functional Description... 3 Installation...
More informationPRODUCT SPECIFICATION FOR A 15 AND 75 kva, THREE PHASE MODULAR POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING (Varian)
PRODUCT SPECIFICATION FOR A 15 AND 75 kva, THREE PHASE MODULAR POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING (Varian) 1.0 General This specification covers the electrical characteristics and
More informationUser's Manual: Series 350T AC Current Input (External Sensor), DC-Powered Transmitters
User's Manual: Series 350T AC Current Input (External Sensor), DC-Powered Transmitters Table of Contents Page Introduction 1 Description 1 Specifications 2 Installation 3 Calibration 4 General Maintenance
More informationM-0418 REV:0
1 of 5 This specification sets forth the minimum requirements for purchase and installation of an aboveground Radar Detection Device (RDD) system for a real-time, stop bar vehicle-detection system that
More informationSPECIAL SPECIFICATION Inch LED Traffic Signal Lamp Unit
1993 Specifications SPECIAL SPECIFICATION 1201 12 Inch LED Traffic Signal Lamp Unit 1. Description. This specification describes the minimum acceptable design and performance requirements for a twelve
More informationMONITOR BRACKETS CCTV SYSTEMS. BT7510S Ex GST Inc GST. BT7511S Ex GST Inc GST. BT7512S Ex GST Inc GST. BT7518S Ex GST Inc GST. BT7513S Ex GST Inc GST
MONITOR BRACKETS BT7510S Small Flat Screen Bracket 20kg For small flat screen. Mounts screen only 20mm from wall. Security Allen Key provided Accommodates up to 20kg BT7511S Small Flat Screen Tilt Bracket
More informationSPECIAL SPECIFICATION 1257 Digital Card Rack Non-Invasive Micro Loop Detector Assembly (8 Slot Rack)
1993 Specifications CSJ 0924-06-147, etc. SPECIAL SPECIFICATION 1257 Digital Card Rack Non-Invasive Micro Loop Detector Assembly (8 Slot Rack) 1. Description. This Item shall govern for furnishing, and
More informationInstruction Manual MX-485-S Bi-directional RS485 Data Transceiver
Instruction Manual MX-485-S Bi-directional RS485 Data Transceiver Copyright 2005, American Fibertek, Inc. 1020JD Table of Contents Functional Description...3 Installation...3 Power Source...3 Power Connection...3
More informationFiberLink 4040 Series
MANUAL FiberLink 4040 Series Four channels of audio over one single mode or multimode fiber. Installation and Operations Manual WWW.ARTEL.COM Contents Contents Welcome... 3 Features... 3 Package Contents...
More informationSUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches
SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches PART 1 GENERAL 1.01 Scope Furnish and install automatic transfer switches (ATS) with number of poles, amperage, voltage, and withstand
More informationTechnical Equipment Specification
STATE OF CALIFORNIA Office of the State Chief Information Officer Public Safety Communications Division Technical Equipment Specification Equipment Type: Transmitter/Receiver Mobile Relay/Base/Control
More informationSWT 3000 Teleprotection technical data siemens.com
Power network telecommunication SWT 3000 Teleprotection technical data siemens.com Sustainable success for high-voltage power networks The SWT 3000 Teleprotection system has been the first choice for reliable
More informationActive CCTV Receiver Balun Installation Guide
Active CCTV Receiver Balun 500015 Installation Guide P/N: 94-000304-C SE-000266-C Copyright Notice: Copyright 2009 MuxLab Inc. All rights reserved. Printed in Canada. No part of this publication may be
More informationTECHNICAL DESCRIPTION
TECHNICAL DESCRIPTION A.M. BROADCAST TRANSMITTER SENDER AM 3000 SS June 2001-1- Rev. B TRANSMITTER CHARACTERISTICS 1. BASIC OFFER The basic offer includes: One AM3000SS A.M. Medium Wave Solid State Broadcast
More information2520 Pulsed Laser Diode Test System
Complete pulse test of laser diode bars and chips with dual photocurrent measurement channels 0 Pulsed Laser Diode Test System Simplifies laser diode L-I-V testing prior to packaging or active temperature
More informationArchitectural/Engineering Specification for a. Microwave Perimeter Intrusion Detection System
Architectural/Engineering Specification for a Microwave Perimeter Intrusion Detection System µltrawave Disclaimer Senstar, and the Senstar logo are registered trademarks, and µltrawave, Silver Network
More informationUser's Manual: Series 450T AC Current Input (External Sensor), AC-Powered Transmitters
User's Manual: Series 450T AC Current Input (External Sensor), AC-Powered Transmitters Table of Contents Page Introduction 1 Description 1 Specifications 2 Installation 3 Calibration 4 General Maintenance
More informationUSER MANUAL. MODEL 2017A RS-232 to 20ma Current Loop Converter. SALES OFFICE (301) TECHNICAL SUPPORT (301)
USER MANUAL MODEL 2017A RS-232 to 20ma Current Loop Converter Part# 07M2017A-A Doc# 073021UA Revised 10/15/93 SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www.patton.com 1.0 WARRANTY
More informationInstruction Manual MX-480 Bi-directional Multi-Protocol Data
Instruction Manual MX-480 Bi-directional Multi-Protocol Data Copyright 2007, American Fibertek, Inc. 1210JD Table of Contents Functional Description...3 Installation...3 Power Source...3 Power Connection...4
More informationSingle-output models feature wide-range output adjustability to meet a wide variety of standard and user-specific output voltage requirements.
Bel Power Solutions MAP55 Series of power supplies provides reliable, tightly-regulated DC power for commercial and industrial systems. Wide-range AC input and full international safety, EMI, and ESD compliance
More informationRFI & EMI Components and Subsystems
RFI & EMI Components and Subsystems In 1979 Filter Networks began manufacturing RFI and EMI components. Filter Networks was acquired in 1997 by EMI Technologies. Our mission then, as now, was simple: to
More information120/240 Watt AC-DC Front End with PFC W Series Convert Select 120 Convert Select 240
Industrial Environment AC-DC Converters >100 Watt W Series 120/240 Watt AC-DC Front End with PFC W Series Convert Select 120 Convert Select 240 Rugged 35 mm DIN-rail snap-fit design 3000 V AC input to
More informationModel 3725/2M. Line Impedance Stabilization Network (LISN) User Manual
Model 3725/2M Line Impedance Stabilization Network (LISN) User Manual ETS-Lindgren L.P. reserves the right to make changes to any product described herein in order to improve function, design, or for any
More informationSPECIAL PROVISION Description of Project, Scope of Contract and Sequence of Work
2004 Specifications CSJ 0110-04-166 SPECIAL PROVISION 000--363 Description of Project, Scope of Contract and Sequence of Work 1. General. The work to be performed on this project consists of furnishing,
More informationSINGLE-PHASE VSV SWITCH
Revision: September 2009 Supersedes: August 2007 SINGLE-PHASE VSV SWITCH INSTALLATION AND OPERATING MANUAL Table of Content: Page I. General...2 II. Specifications...2 III. Installation...3 IV. Maintenance...5
More informationSPECIAL SPECIFICATION 6647 Automated Barrier Gate Assembly
1995 Metric CSJ 0015-13-299 SPECIAL SPECIFICATION 6647 Automated Barrier Gate Assembly 1. Description. This Item shall govern for the furnishing and installation of an Automated Barrier Gate (ABG) assembly
More informationInstruction Manual RT-93285SL RR-93285SL Thirty-two Channel Video Multiplexer With Two Bi-directional Data Channels
Instruction Manual RT-93285SL RR-93285SL Thirty-two Channel Video Multiplexer With Two Bi-directional Data Channels Copyright 2006, American Fibertek, Inc. 0222JD Table of Contents Functional Description...3
More informationSINGLE-PHASE VSV SWITCH
May 2006 Supercedes: March 2006 SINGLE-PHASE VSV SWITCH INSTALLATION AND OPERATING MANUAL Table of Content: Page I. General...2 II. Specifications...2 III. Installation...2 IV. Maintenance...4 V. VSV Power
More informationPower Supplies 3. SDN-C Compact DIN Rail Series
SDN-C Compact DIN Rail Series The SDN-C DIN rail power supplies are the next generation of the popular SDN series. These models combine high efficiency and compact size with new visual diagnostic LEDs
More informationMICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK
MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK SIG:EMS 1 of 6 APPR:LWB:DBP:07-14-15 FHWA:APPR:07-28-15 a. Description. This work consists of site
More information2017 Advanced Energy Industries, Inc. PEII SERIES LOW-FREQUENCY POWER SUPPLIES 5 TO 60 KW
2017 Advanced Energy Industries, Inc. PEII SERIES LOW-FREQUENCY POWER SUPPLIES 5 TO 60 KW Enhanced arc control with internal load matching for 40 khz reactive sputtering applications Page 2 The PEII power
More informationIntelix DIGI-VGASD-R Installation Manual
Intelix DIGI-VGASD-R Installation Manual Introduction The Intelix DIGI-VGASD-R active receiver balun transmits VGA video, stereo audio, and IR or RS232 up to 350 feet over a single twisted pair cable.
More informationMICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK
MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK SIG:CJS 1 of 6 APPR:EMS:DBP:06-29-17 FHWA:APPR:08-14-17 a. Description. This work consists of completing
More information285E Series DIGITAL FIBER OPTIC AUDIO/DATA TRANSPORT SYSTEM
285E Series DIGITAL FIBER OPTIC AUDIO/DATA TRANSPORT SYSTEM BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability is assumed as a result
More informationIntelix DIGI-VGASD-S Installation Manual
Intelix DIGI-VGASD-S Installation Manual Introduction The Intelix DIGI-VGASD-S active send balun transmits VGA video, stereo audio, and IR or RS232 up to 350 feet over a single twisted pair cable. The
More informationInstruction Manual Model M Switch, DPDT, Manual Select
Instruction Manual Model 1582-70M Switch, DPDT, Manual Select November 2018 Rev 0 STATUS MODEL 1582 CROSS TECHNOLOGIES INC. MANUAL SELECT POWER Data, drawings, and other material contained herein are proprietary
More informationIntelix DIGI-VGASD Installation Manual
Intelix DIGI-VGASD Installation Manual Introduction The Intelix DIGI-VGASD active balun set transmits VGA video, stereo audio, and IR or RS232 up to 350 feet over a single twisted pair cable. The balun
More informationMLA High Performance Microstepping Driver. User s Guide E. Landon Drive Anaheim, CA
MLA10641 High Performance Microstepping Driver User s Guide A N A H E I M A U T O M A T I O N 4985 E. Landon Drive Anaheim, CA 92807 e-mail: info@anaheimautomation.com (714) 992-6990 fax: (714) 992-0471
More informationInterBOARD TM 12 Channel Transmitter and Receiver Evaluation Board User Guide
InterBOARD TM 12 Channel Transmitter and Receiver Evaluation Board User Guide SN-E12-X00501 Evaluation Board Features: Single Board compatible with Transmitter and Receiver Designed to operate up to 3.5
More informationInterface: Serial EIA RS-232D/CCITT V.24, DCE; RTS/CTS delay 0,8 or 64 ms (user-selectable).
BLACK BOX PWR RTS TD-1 RD-1 TD-2 DCD RD-2 TEST DIG ANA REM LDM-MR 19.2 REM ANA DIG AGC 2/4 WIRE ABLE / ABLE SWITCHES 2 W 4 W 1 2 3 4 CARRIER LEVEL 0 dbm -3 dbm -6 dbm -9 dbm PIN 21 (RLB) RPF PIN 18 AN.
More informationSECTION COMMUNICATIONS ELECTRICAL POWER DISTRIBUTION
SECTION 16715 COMMUNICATIONS ELECTRICAL POWER DISTRIBUTION PART 1 - GENERAL 1.01 SECTION DESCRIPTION AND BASIC REQUIREMENTS A. The Electrical Power Distribution System provides power distribution from
More informationSPECIFICATION AND PERFORMANCE CHARACTERISTICS SERIAL ATA CABLE ASSEMBLIES
SPECIFICATION AND PERFORMANCE CHARACTERISTICS OF SERIAL ATA CABLE ASSEMBLIES CIRCUIT ASSEMBLY CORP. 18 THOMAS STREET, IRVINE, CA 92618-2777 Page No. 1 CONTENTS: 1.0 SCOPE.. 3 2.0 APPLICABLE DOCUMENTS 3
More informationIntelix DIGI-V3SD-R Installation Manual
Intelix DIGI-V3SD-R Installation Manual Introduction When used in conjunction with a compatible send balun, distribution amplifier, or matrix switcher, the Intelix DIGI-V3SD-R active balun transmits component
More informationPROFESSIONAL POWER AMP
Operating Instruction Manual PROFESSIONAL POWER AMP Model P-75D, P-150D, P-300D P-75D P-150D P-300D TOA Corporation KOBE, JAPAN Contents Precautions... 1 General Description... 2 Features... 2~ 3 Specifications...
More informationMGL Avionics Autopilot. Servo. Specifications & Installation Manual. Last Update: 20 October Disclaimer:
MGL Avionics Autopilot Servo Specifications & Installation Manual Last Update: 20 October 2010 Disclaimer: MGL Avionics should not be held responsible for errors or omissions in this document. Usage of
More informationPIRANHA 3 (3-phase, Power Conditioning Voltage Regulator)
PRODUCT SPECIFICATION FOR A 15 THRU 500 kva, THREE PHASE, MODULAR POWER REGULATOR AND CONDITIONER PIRANHA 3 (3-phase, Power Conditioning Voltage Regulator) 1.0 General This specification covers the electrical
More informationSince 1987 Developed, Created and Made in Spain NDV6/ND6V VIDEO & DATA TRANSCEIVER, AUDIO & CONTACT
Since 987 Developed, Created and Made in Spain NDV6/ND6V VIDEO & DATA TRANSCEIVER, AUDIO & CONTACT CONTENTS General functionality and features of the equipment. Technical specifications. Application. Connection
More informationTOSHIBA International Corp
TOSHIBA International Corp GUIDE SPECIFICATIONS THREE PHASE UNINTERRUPTIBLE POWER SYSTEM TOSHIBA 4200FA 30 kva CT Internal Battery UPS GUIDE SPECIFICATIONS 1 (30 kva CT) 1.0 SCOPE 1.1 System This specification
More informationVHF LAND MOBILE SERVICE
RFS21 December 1991 (Issue 1) SPECIFICATION FOR RADIO APPARATUS: VHF LAND MOBILE SERVICE USING AMPLITUDE MODULATION WITH 12.5 khz CARRIER FREQUENCY SEPARATION Communications Division Ministry of Commerce
More informationEDACS WALL MOUNT STATION. Maintenance Manual. Mobile Communications LBI-31838A TABLE OF CONTENTS
A Mobile Communications EDACS WALL MOUNT STATION TABLE OF CONTENTS SYSTEM BOARD & REGULATOR BOARD.......... LBI-31892 KEY/DISPLAY BOARD MAINTENANCE MANUAL.... LBI-31940 Maintenance Manual Printed in U.S.A.
More informationVideo/Audio Transmission System Series VA700. (formerly Series DVL4A)
Video/Audio Transmission System Series VA700 (formerly Series DVL4A) November 2000 1 VIDEO/AUDIO TRANSMISSION SYSTEM INSTRUCTION MANUAL SERIES VA700 & VA700M General The Series VA700 is a transmission
More informationaf i Instruction Manual MR-944C Four Channel Video Receiver With One Bi-Directional Multi-Protocol Data Channel american fibertek 11/30/2012 JPK
af i american fibertek Instruction Manual MR-944C Four Channel Video Receiver With One Bi-Directional Multi-Protocol Data Channel 11/30/2012 JPK Table of Contents Functional Description... 3 Installation...
More informationPRODUCT SPECIFICATION
2.54mm Board to Board Header Connectors Page 1 1.0 SCOPE This specifies Pitch 2.54mm Headers Connectors. The connector shall meet the performances, specified here under the condition with the plug connector
More informationCable and Port Specifications
APPENDIX D This appendix includes the following information: Cables and Adapters Provided, page D-1 Console Port, page D-2 COM1 Port, page D-3 MGMT 10/100 Ethernet Port, page D-5 SFP Transceiver Specifications,
More informationTECHNICAL PRODUCT DATASHEET
FORM-ENG-0018 REV A 06-02-03 ISO 9001 CERTIFIED Phone: (352) 629-5020 or 800-533-3569 Fax: (352)-629-2902 SUITABLE FOR OEM DISTRIBUTION ONLY TECHNICAL PRODUCT DATASHEET High Density PDM 21 Output / 10
More informationFIBER OPTIC ANTENNA LINK OFW-5800/GPS. Compatible with a Wide Range of GPS Receivers Architectures. Logistically Supported with COTS Hardware
FIBER OPTIC ANTENNA LINK OFW-5800/GPS Compatible with a Wide Range of GPS Receivers Architectures Designed to Operate within the Naval Electromagnetic Environment Designed and Manufactured to Meet Naval
More informationGeneral Application Notes Remote Sense Remote On / Off Output Trim Series Operation Parallel Operation...
General... 28 Remote Sense... 29 Remote On / Off... 30 Output Trim... 30 Series Operation... 32 Parallel Operation... 33 Synchronization... 33 Power Good Signal... 34 Electro Magnetic Filter (EMI)... 34
More informationPRODUCT INFORMATION B&B ELECTRONICS. Port-Powered RS-232 Fiber Optic Modem with Handshake Support. Model 9PFLST. Description. RS-232 Connections
-01-1/ 00 by B&B Electronics. All rights reserved. Model Port-Powered RS- Fiber Optic Modem with Handshake Support Description The allows any two pieces of RS- asynchronous serial equipment to communicate
More informationTOA PROFESSIONAL POWER AMP
Operating Instruction Manual TOA PROFESSIONAL POWER AMP Model P-150M, P-300M TOA ELECTRIC CO, LTD. KOBE, JAPAN Contents Precautions... 2 General Description... 2 Features... 3 Specifications... 4~5 Performance
More informationRequirements and Test Methods for Very-High-Bit-Rate Digital Subscriber Line (VDSL) Terminal Equipment
VDSL(E) Issue 1 (Provisional) January 2003 Terminal Attachment Program Requirements and Test Methods for Very-High-Bit-Rate Digital Subscriber Line (VDSL) Terminal Equipment Aussi disponible en français
More informationPRODUCT SPECIFICATION
0.8x1.2 mm Board to Board Socket Connectors Page 1 1.0 SCOPE This specifies 0.8x1.2mm pitch Socket Connectors. The connector shall meet the performances, specified here under the condition with the plug
More informationSurge Generator for MIL-STD 1275
Surge Generator for MIL-STD 1275 This generator PG1275 is specially designed for the test of the susceptibility to surges and spikes of military 28 Vdc electric circuits. The equipment allows performing
More informationSECTION 16483D ADJUSTABLE FREQUENCY DRIVE - MICRODRIVE (MVX <10-HP)
ADJUSTABLE FREQUENCY DRIVE - MICRODRIVE (MVX
More informationCPCO Series DC-AC Current Probe, Clamp On, 160mm, ±1000A ±2000A ±4000A ±8000A ±12000A, ±16000A
The CPCO Series (160mm aperture) Current Probes are Clamp On current sensors capable of measuring ac and dc currents. The Current Probe splits along a diameter allowing easy installation to existing cables
More informationPOWER DELEGATOR SERIES 7200A POWER DISTRIBUTION UNIT WITH POWER CONDITIONING GENERAL SPECIFICATIONS
POWER DELEGATOR SERIES 7200A POWER DISTRIBUTION UNIT WITH POWER CONDITIONING GENERAL SPECIFICATIONS 1.0 SCOPE The following specification describes the features, design, and application of the Series 7200A
More informationModel 34A. 3Hz to 2MHz 2-Channel Butterworth/Bessel HP, LP, BP, BR Plug-In Filter Card for Model 3905/3916 Chassis.
Model 34A 3Hz to 2MHz 2-Channel Butterworth/Bessel HP, LP, BP, BR Plug-In Filter Card for Model 3905/3916 Chassis Operating Manual Service and Warranty Krohn-Hite Instruments are designed and manufactured
More informationOM7AT & OM7AR1 (Stand alone) ROM7AT & ROM7AR1 (Rack mount)
OM7AT & OM7AR1 (Stand alone) ROM7AT & ROM7AR1 (Rack mount) IRIG Time Code Electrical to Fiber Optic Transceiver Operating Manual Rev. 1.3 December 20, 2015 Luxcom Technologies Inc., 102 WALGREEN ROAD,
More informationMODEL FLD-496SA 9600 Baud FIBER OPTIC/FSK MODEM
1 MODEL FLD-496SA 9600 Baud FIBER OPTIC/FSK MODEM GDI COMMUNICATIONS, LLC 280 Interstate 80 Exit 1 PO Box 1330 Verdi, NV 89439 Phone (775) 345-8000 Fax (775) 345-8010 PROPRIETARY DATA This document contains
More informationAU INSTALLATION INSTRUCTIONS. Revision B1 Rapid City, SD, USA, 02/2010 II_201A-AU_B1
INSTALLATION INSTRUCTIONS Revision B1 Rapid City, SD, USA, 02/2010 MODELS 201A-AU 201-575-AU II_201A-AU_B1 2880 North Plaza Drive, Rapid City, South Dakota 57702 (800) 843-8848 (605) 348-5580 fax (605)
More information100G CWDM4 MSA Technical Specifications 2km Optical Specifications
100G CWDM4 MSA Technical Specifications 2km Specifications Participants Editor David Lewis, LUMENTUM Comment Resolution Administrator Chris Cole, Finisar The following companies were members of the CWDM4
More informationThe wireless alternative to expensive cabling...
The wireless alternative to expensive cabling... ELPRO 105U ISO 9001 Certified New Products... New Solutions The ELPRO 105 range of telemetry modules provide remote monitoring and control by radio or twisted-pair
More informationRockwell Collins, Inc. VHF Users Manual
Rockwell Collins, Inc. VHF-2200 Users Manual This manual provided to the FCC for product guidance, it should not be used by our OEM customers. Scope: This document will detail information required to install
More informationEUROPEAN pr ETS TELECOMMUNICATION February 1996 STANDARD
FINAL DRAFT EUROPEAN pr ETS 300 118 TELECOMMUNICATION February 1996 STANDARD Second Edition Source: ETSI TC-TE Reference: RE/TE-05049 ICS: 33.020 Key words: PSTN, modems Public Switched Telephone Network
More informationPart I: Requirements for Terminal Equipment (TE) and Related Access Arrangements Intended for Direct Connection to Analog Wireline Facilities
Issue 9, Amendment 5 March 2016 Spectrum Management and Telecommunications Compliance Specification for Terminal Equipment, Terminal Systems, Network Protection Devices, Connection Arrangements and Hearing
More information411LA Broadband Power Amplifier
411LA Broadband Power Amplifier HIGH RF VOLTAGES MAY BE PRESENT AT THE OUTPUT OF THIS UNIT. All operating personnel should use extreme caution in handling these voltages and be thoroughly familiar with
More informationAFBR-59F2Z Data Sheet Description Features Applications Transmitter Receiver Package
AFBR-59F2Z 2MBd Compact 6nm Transceiver for Data communication over Polymer Optical Fiber (POF) cables with a bare fiber locking system Data Sheet Description The Avago Technologies AFBR-59F2Z transceiver
More informationMaintenance Manual. Simulcast Interface Panel 19D904009G5 & G4. ericssonzy LBI TABLE OF CONTENTS
Maintenance Manual Simulcast Interface Panel 19D904009G5 & G4 TABLE OF CONTENTS EDACS Interface Module 1... EDACS Serial Module... PTT Module... Power Monitor For Simulcast... TUAI Module/Simulcast TX
More information