DEEP PENETRATING EDDY CURRENT for DETECTING VOIDS in COPPER

Size: px
Start display at page:

Download "DEEP PENETRATING EDDY CURRENT for DETECTING VOIDS in COPPER"

Transcription

1 DEEP PENETRATING EDDY CURRENT for DETECTING VOIDS in COPPER Tadeusz Stepinski (Uppsala University, Signals and System, P.O.Box 528, SE-75 2 Uppsala, Sweden, ts@signal.uu.se) Abstract Assessment of copper canisters for spent nuclear fuel requires means for detecting and sizing voids as small as mm in diameter, located up to 4 mm under the surface. Eddy current technique for the detection and characterisation of deep voids in copper is presented in the paper. Results were obtained using two deep penetrating probes, the standard MDK 33 from Rohman, and a specially designed probe MDF 2 from Leotest. The detection ability of the above probes was evaluated and compared using a specially designed sandwich specimen. The specimen was designed to simulate voids with different volumes, located in copper at different depths. Eddy current responses of the two probes were acquired using an automatic scanner for a number of artificial voids with different depths and volumes. The method of defect characterisation (estimating void depth and size) was established. It was shown that the detection of artificial void (cylinder with diameter mm and height mm) located at the depth of 4 mm was possible using the probe MDF 2 at the test frequency of approx. 7Hz. It appeared that defect characterisation was relatively simple task consisting of two steps, estimating the void depth based on the phase angle of its response, and using EC response amplitude for estimating the void diameter. Introduction This paper discusses the use of eddy current technique (ET) for detecting deep subsurface defects in copper. The ET is intended as one of three NDT techniques used for assessing the integrity of the circumferential electron beam (EB) welds between the lid and walls of the copper-lined canisters developed by SKB (Swedish Nuclear Fuels and Waste Management Co.). The canisters that will be used for encapsulation of nuclear spent fuel have the form of 5 m high cylinders with diameter of approx. m (for details see ()). The canisters are sealed by means of an EB weld, which has to be inspected nondestructively. Due to the radiation emitted by the nuclear waste encapsulated in the canisters the inspection must be carried out completely automatically. Three complementary NDT techniques have been developed for this application: a digital X-ray system, an ultrasonic array system (more details in (2)), and a deep penetrating ET. The ET is used for increasing the probability of detection of the most critical defects located up to 4 mm under surface of the canister outer wall. The defects that result in the EB welding process take the form of voids located in the weld zone. Specification for the ET requires detecting and sizing voids as small as mm in diameter, located up to 4 mm under the outer canister surface.

2 Preliminary investigation of a conventional ET has shown that penetration depth obtained using a suitable commercially available probe fed with frequency in the range of khz would be sufficient for the application. Results of a detailed study aimed at optimising the detection and sizing deep flaws in copper are presented in this paper. The EC probes that have been compared in the study are listed in Table. Table. EC probes used in experiments Manufacturer Probe type Description ESR Rohman MDK 33 LEOTEST Lvov MDF 2 Deep penetrating probe for inspection of riveted aluminum structures Deep penetrating probe for nonferrous material, penetration depth up to 8mm The detection ability of the above listed probes was evaluated and compared using sandwich specimen presented below. Dependence of eddy current responses on the defect parameters (defect depth and size) was established and used for the development of defect characterization method. Experimental Special test specimen was designed and manufactured to simulate voids in copper of different volumes located at different depths. The specimen has the form of sandwich consisting of three layers: the upper layer for simulating given depth, the middle consisting holes, and a bottom plate (see Fig. ). To assure minimum gaps between the plates a special system of air channels that facilitated pumping out air from the space between the plates using a vacuum pump was machined in the upper and the base plate. Then the atmospheric pressure pressed the plates together. EC probe Upper plate Middle plate Hole Base plate Figure. Test object, simulating voids with certain volume located at certain depth. The depth of the voids, t d could be varied by changing the thickness of the upper plate. The void volume was a function of thickness of the middle plate t v and hole diameter d h. Each middle plate consisted 4 x 3 = 2 holes with different diameters; all plates had identical hole locations. A series of measurements was performed to evaluate and compare the performance of the selected probes. Linear scans of six holes with diameters d h in the range from,8 mm to 3, mm, placed under upper plates with depths t d from mm to 4 mm, were performed. The holes had different volumes due to the variable thickness t v of the middle plate (cf. Fig. ).

3 The volumes of the test holes varied from.5 mm 3 (for d h =.8 mm and t d = mm) to 28,3 mm 3 (for d h = 3 mm and t d = 4 mm). The EC signals were acquired in each scan and the respective signal amplitudes, phase angles and signal to noise ratios (S/N) were estimated Figure 2. Example of response of the Probe MDF 2 to 3 different holes. Dashed line defines signal phase and interval between the dotted lines is a measure of signal amplitude. Signal amplitude was found as the maximum length of the signal projection on the direction defined by its phase (see Figure 2). Signal to noise ratio was estimated as a quote of the signal amplitude (difference between the maximum and minimum of the signal projection) to max deviation of the noise projection expressed in db using the following formula: S / N abs 2log signal noise where signal, noise max variation of signal and noise, respectively The probes were scanned in contact with the upper Cu plate using an XY scanner connected to a PC based EC acquisition system. Due to the specimen geometry and the scanner size only three holes could be scanned at a time and therefore the results obtained for the respective scans for each combination of upper and middle plate thickness are slightly different. The probes were connected to ESR Rohman PL.E EC instrument and the following parameters were chosen: operating frequency 72 Hz, probe excitation 5 gain 6 85 db (depending on upper plate thickness), filter DC to 8 Hz. Probes The MDK 33 is a deep penetrating, multi-differential probe developed for aerospace applications. It has a considerable size (square 25 x 25 mm) and a high penetration depth. The probe is made up of four different windings forming a cross pattern. 2D response of this probe is shown in Figure 3a. The MDF 2 probe, developed by LEOTEST Lvov belongs to 2DD family that will be presented in detail at the same conference (3). It has very similar characteristics to MDK 33; it is also a deep penetrating, multi-differential

4 probe but with a smaller size (diameter 3 mm) and a very high penetration depth. The 2D response of this probe is shown in Figure 3b. The 2D responses reveal that both probes are build of four separate windings arranged in a cross pattern. Probe symmetry can be easily evaluated based on its 2D responses. It is worth noting that the EC patterns in the impedance plane obtained when scanning small defects with the multi-differential probes depend strongly on the direction of scanning. If scanning is performed along one of the probe axes shown in Fig. 3 the probe has a quasi-absolute asymmetric response shown in Fig. 4. The response may have a positive or negative sign depending on the chosen axis of scanning. In the worst case when the direction of scanning is diagonal, the probe response may be very week and may differ considerably from the patterns shown in Fig. 4. This means that care should be taken when performing sparse scanning using probes of this type, especially when the acquired EC signals are to be used for sizing of the detected defects. m m m m mm mm Figure 3. 2D responses of the probes measured as their response to a small hole in copper plate (note different scan areas). Probe MDK 33 and Probe MDF Figure 4. EC patterns of the probes measured as their response to 3 holes in a copper plate. Probe MDK 33 and Probe MDF 2.

5 The EC patterns shown in Fig. 4 acquired as a single line scan along 3 holes with different diameters reveal strong similarity of the probes. Shape of the EC Pattern allows judging the relative position of the probe and the scanned holes. If in the scan shown Fig 4, the hole line was adjusted accurately with the probe axis the responses would be symmetrical (no double lines would be observed).

6 Results The above-presented probes were used for scanning the specimen shown in Fig. and thickness of the both plates was changed from to 4 mm to simulate voids with different volumes located at different depths. The linear scans were acquired for different hole diameters and the EC data was saved and processed off line to evaluate phase, amplitude and S/N as a function of hole diameter, depth and volume. The first step in data processing was phase evaluation. This was made manually using the method illustrated in Fig. 2. In the second step the signal was rotated to align its phase with the vertical axis. The amplitudes and S/N ratios were evaluated using the vertical component in the next step. Examples of the responses measured for three holes located at the depth o 3 mm are shown in Fig. 5 and the their vertical components used for the evaluation in Fig Figure 5. EC responses of the probes to a.8, 2 & 3 mm holes in copper plate at the depth 3 mm. Probe MDK 33 and Probe MDF Figure 6. In-phase components of the EC patterns shown in Fig. 5. Probe MDK 33 and Probe MDF 2. From Fig. 6 can be seen that a hole with diameter,8 mm located at the depth of 3 mm can be detected using both probes, the corresponding S/N was 4 to 7 db for the MDK 33, and 6 to 8 db for the probe MDF 2. The signal to noise ratio was influenced by the hole volume (thickness of the middle plate t v ). However, as shown in Fig 6, the same hole

7 located at the depth 4 mm could not be detected by the MDK 33 while the S/N observed for the MDF 2 was 2 to 3 db Figure 6. In-phase components of the EC responses to a.8, 2 & 3 mm holes in copper plate at the depth 4 mm. Probe MDK 33 and Probe MDF 2. Absolute signal levels measured for both probes as a function of the hole diameter and with hole depth as parameter are presented in Fig. 7. Signal level as a function of hole diameter (hole hight 4 mm) Signal level as a function of hole diameter (hole hight 4 mm),7,6,5 Signal level,5,4,3,2,,,,5 2, 2,5 3, Hole diameter in mm Depth mm Depth 2 mm Depth 3 mm Depth 4 mm Signal level,,5,,,5 2, 2,5 3, Hole diameter in mm Depth mm Depth 2 mm Depth 3 mm Depth 4 mm Figure 7. Signal level as a function of the hole diameter for various depths t d. Probe MDK 33. Probe MDF 2 Distinct phase differences depending on the hole depth were observed for both probes. Phase information together with the response amplitude enabled reliable defect sizing. Defect characterization Defect sizing is relatively simple task that can consist of two steps: Estimating defect depth based on the phase angle of its response Using EC amplitude for estimating defect cross section (diameter) It should be noted that phase of the EC response should be measured as shown in Figure 2, i.e., as an angle of the tangent to the responses with different amplitudes. The conventional measurement of an angle of a line connecting a point with the maximum amplitude with the origin of coordinates resulted in an undesired variation of the phase angle with

8 response amplitude. The tangent angle seems to be more robust parameter uniquely defining defect depth. Phase angles as a functionof hole depth 9 8 Phase in degrees ,5 2 2,5 3 3,5 4 4,5 Hole depth in mm Hole hight 2 mm Hole hight 3 mm Hole hight 4 mm linar prediction Figure 8. Phase angle as a function of hole depth for scan A. A straight line estimated from the mean phase values is also shown. The result of linear phase approximation can be seen Fig. 8. A linear regression based on mean values of phase angles corresponding to different hole heights resulted in a straight line (diamonds in Fig. 8). This means that this line with a slope of approx. 4 per mm can be used for the estimation of defect depth.,2 Signal level as a function of hole depth (hole diameter 2 mm) Signal level,8,4, Hole depth in mm Height mm Height 2 mm Height 3 mm Height 4 mm Figure 9. Signal level as a function of hole depth for hole diameter 2mm. When the hole depth t d is known its diameter can be estimated form a family of curves shown in Fig. 9. From Fig. 9 can be seen that the response amplitude does not depend on the hole height for the t v = 2 to 5 mm. It appeared strange that a different curve was obtained for the t v =mm, however, closer examination has shown that the conductivity of mm plate differed from that of the other plates. Difference in responses was also observed when this plate was used as an upper plate for simulating mm depth (t d = mm).

9 Conclusions Analysis of the collected EC data and the figures presented above leads to the following conclusions: Sensitivity: It is possible to detect holes as small as mm diameter at the depth of 4 mm in pure copper using a deep penetrating EC probe and a frequency < khz. Hole with diameter,8 mm at the depth of 4 mm was detected with S/N = 3 db using probe MDF 2. Phase angles change linearly with the hole depth t d, however, they are relatively insensitive to the hole height t v. Signal amplitude (level) increases with the hole diameter and decreases with the hole depth t d, however, it is relatively insensitive to the hole height t v. The dependence between the hole diameter and signal amplitude is linear while dependence between hole depth and signal amplitude is exponential. Signal to noise ratio S/N increases with the hole diameter and decreases with its depth t d, however, it is relatively insensitive to the hole height t v. References () C-G. Andersson and R.E. Andrews The Development of Advanced Welding Techniques for Sealing Nuclear Waste Canisters, Presented at 2 MRS Sprig Meeting, April 2, San Francisco, SKB report, TR--25, pp (2) T. Stepinski, P. Wu, M.G. Gustafsson and L. Ericsson, Ultrasonic array technique for the inspection of copper lined canisters for nuclear waste fuel, Proc of the 7th ECNDT, Copenhagen, May 998, pp (3) V. Uchanin, G. Mook and T. Stepinski, The investigation of deep penetrating high resolution EC probes for subsurface flaw detection and sizing, to be presented at 8th ECNDT, Barcelona, June 22.

ULTRASONIC IMAGING of COPPER MATERIAL USING HARMONIC COMPONENTS

ULTRASONIC IMAGING of COPPER MATERIAL USING HARMONIC COMPONENTS ULTRASONIC IMAGING of COPPER MATERIAL USING HARMONIC COMPONENTS T. Stepinski P. Wu Uppsala University Signals and Systems P.O. Box 528, SE- 75 2 Uppsala Sweden ULTRASONIC IMAGING of COPPER MATERIAL USING

More information

New portable eddy current flaw detector and application examples

New portable eddy current flaw detector and application examples 11th European Conference on Non-Destructive Testing (ECNDT 2014), October 6-10, 2014, Prague, Czech Republic New portable eddy current flaw detector and application examples More Info at Open Access Database

More information

Array Eddy Current for Fatigue Crack Detection of Aircraft Skin Structures

Array Eddy Current for Fatigue Crack Detection of Aircraft Skin Structures Array Eddy Current for Fatigue Crack Detection of Aircraft Skin Structures Eric Pelletier, Marc Grenier, Ahmad Chahbaz and Tommy Bourgelas Olympus NDT Canada, NDT Technology Development, 505, boul. du

More information

Tadeusz Stepinski and Bengt Vagnhammar, Uppsala University, Signals and Systems, Box 528, SE Uppsala, Sweden

Tadeusz Stepinski and Bengt Vagnhammar, Uppsala University, Signals and Systems, Box 528, SE Uppsala, Sweden AUTOMATIC DETECTING DISBONDS IN LAYERED STRUCTURES USING ULTRASONIC PULSE-ECHO INSPECTION Tadeusz Stepinski and Bengt Vagnhammar, Uppsala University, Signals and Systems, Box 58, SE-751 Uppsala, Sweden

More information

DETECTION OF THE SUBSURFACE CRACKS PROPAGATED FROM RIVET HOLES IN THE MULTILAYER AIRCRAFT STRUCTURES

DETECTION OF THE SUBSURFACE CRACKS PROPAGATED FROM RIVET HOLES IN THE MULTILAYER AIRCRAFT STRUCTURES XXIV Seminarium NIENISZCZĄCE BADANIA MATERIAŁÓW Zakopane, 14-16 marca 2018 DETECTION OF THE SUBSURFACE CRACKS PROPAGATED FROM RIVET HOLES IN THE MULTILAYER AIRCRAFT STRUCTURES Valentyn UCHANIN Karpenko

More information

Multi-Parameter POD for Industrial Applications The Influence of the Material Attenuation as an Example

Multi-Parameter POD for Industrial Applications The Influence of the Material Attenuation as an Example Seminar des Fachausschusses Ultraschallprüfung - Vortrag 14 Multi-Parameter POD for Industrial Applications The Influence of the Material Attenuation as an Example Mato PAVLOVIC, Rainer BOEHM, Christina

More information

NARROWBAND ULTRASONIC SPECTROSCOPY FOR NDE OF LAYERED STRUCTURES T. Stepinski and M. Jonsson 1 Uppsala University, Uppsala, Sweden

NARROWBAND ULTRASONIC SPECTROSCOPY FOR NDE OF LAYERED STRUCTURES T. Stepinski and M. Jonsson 1 Uppsala University, Uppsala, Sweden NARROWBAND ULTRASONIC SPECTROSCOPY FOR NDE OF LAYERED STRUCTURES T. Stepinski and M. Jonsson 1 Uppsala University, Uppsala, Sweden Abstract: NDE of airspace sandwich structures is often performed using

More information

INVESTIGATION OF IMPACT DAMAGE OF CARBON FIBER- RAINFORCED PLASTIC (CFRP) BY EDDY CURRENT NON- DESTRUCTIVE TESTING

INVESTIGATION OF IMPACT DAMAGE OF CARBON FIBER- RAINFORCED PLASTIC (CFRP) BY EDDY CURRENT NON- DESTRUCTIVE TESTING International Workshop SMART MATERIALS, STRUCTURES & NDT in AEROSPACE Conference NDT in Canada 2011 2-4 November 2011, Montreal, Quebec, Canada INVESTIGATION OF IMPACT DAMAGE OF CARBON FIBER- RAINFORCED

More information

VD3-71 universal eddy current flaw detector application for field inspection of aeronautical engineering

VD3-71 universal eddy current flaw detector application for field inspection of aeronautical engineering VD3-71 universal eddy current flaw detector application for field inspection of aeronautical engineering Introduction. The Document reviewed by http://engineermind.com/ By ahmed@engineermind.com The need

More information

Eddy Current Testing (ET) Technique

Eddy Current Testing (ET) Technique Research Group Eddy Current Testing (ET) Technique Professor Pedro Vilaça * * Contacts: Address: Puumiehenkuja 3 (room 202), 02150 Espoo, Finland pedro.vilaca@aalto.fi October 2017 Contents Historical

More information

Corrosion Steel Inspection under Steel Plate Using Pulsed Eddy Current Testing

Corrosion Steel Inspection under Steel Plate Using Pulsed Eddy Current Testing 4th International Symposium on NDT in Aerospace 2012 - Poster 4 Corrosion Steel Inspection under Steel Plate Using Pulsed Eddy Current Testing D.M. SUH *, K.S. JANG **, J.E. JANG **, D.H. LEE ** * Raynar

More information

Steam Generator Tubing Inspection

Steam Generator Tubing Inspection 6th International Conference on NDE in Relation to Structural Integrity for Nuclear and Pressurized Components October 27, Budapest, Hungary For more papers of this publication click: www.ndt.net/search/docs.php3?mainsource=7

More information

Challenges and New Developments for Air Coupled Ultrasonic Imaging

Challenges and New Developments for Air Coupled Ultrasonic Imaging Abstract Challenges and New Developments for Air Coupled Ultrasonic Imaging Wolfgang Hillger, Artur Szewieczek, Detlef Ilse, Lutz Bühling 1 1 Ingenieurbüro Dr. Hillger Ultrasonic-Techniques, info@dr-hillger.de

More information

NDT-PRO Services expands service offering

NDT-PRO Services expands service offering NDT-PRO Services expands service offering NDT-PRO Services announced the formal release of two advanced NDT methods, Phased Array (including TOFD) and Eddy Current. What are they and where are the used?

More information

Keywords: Ultrasonic Testing (UT), Air-coupled, Contact-free, Bond, Weld, Composites

Keywords: Ultrasonic Testing (UT), Air-coupled, Contact-free, Bond, Weld, Composites Single-Sided Contact-Free Ultrasonic Testing A New Air-Coupled Inspection Technology for Weld and Bond Testing M. Kiel, R. Steinhausen, A. Bodi 1, and M. Lucas 1 Research Center for Ultrasonics - Forschungszentrum

More information

Fastener Hole Crack Detection Using Adjustable Slide Probes

Fastener Hole Crack Detection Using Adjustable Slide Probes Fastener Hole Crack Detection Using Adjustable Slide Probes General The guidelines for the adjustable sliding probes are similar to the fixed types, therefore much of the information that is given here

More information

Weld gap position detection based on eddy current methods with mismatch compensation

Weld gap position detection based on eddy current methods with mismatch compensation Weld gap position detection based on eddy current methods with mismatch compensation Authors: Edvard Svenman 1,3, Anders Rosell 1,2, Anna Runnemalm 3, Anna-Karin Christiansson 3, Per Henrikson 1 1 GKN

More information

2.5D Finite Element Simulation Eddy Current Heat Exchanger Tube Inspection using FEMM

2.5D Finite Element Simulation Eddy Current Heat Exchanger Tube Inspection using FEMM Vol.20 No.7 (July 2015) - The e-journal of Nondestructive Testing - ISSN 1435-4934 www.ndt.net/?id=18011 2.5D Finite Element Simulation Eddy Current Heat Exchanger Tube Inspection using FEMM Ashley L.

More information

Eddy Current Array for Aerospace

Eddy Current Array for Aerospace NANDT Conference 2017 Eddy Current Array for Aerospace Presented by Richard Nowak Olympus Product Manager NDT Material provided by Ghislain Morais, OSSA Eddy Current Array ECA Instrument OmniScan ECA:

More information

Eddy Current Modelling for Fasteners Inspection in Aeronautic

Eddy Current Modelling for Fasteners Inspection in Aeronautic ECNDT 2006 - Tu.4.4.5 Eddy Current Modelling for Fasteners Inspection in Aeronautic Séverine PAILLARD, Grégoire PICHENOT, CEA Saclay, Gif-sur-Yvette, France Marc LAMBERT, L2S (CNRS-Supélec-UPS), Gif-sur-Yvette

More information

Developments in Ultrasonic Guided Wave Inspection

Developments in Ultrasonic Guided Wave Inspection Developments in Ultrasonic Guided Wave Inspection Wireless Structural Health Monitoring Technology for Heat Exchanger Shells using Magnetostrictive Sensor Technology N. Muthu, EPRI, USA; G. Light, Southwest

More information

Maximizing the Fatigue Crack Response in Surface Eddy Current Inspections of Aircraft Structures

Maximizing the Fatigue Crack Response in Surface Eddy Current Inspections of Aircraft Structures Maximizing the Fatigue Crack Response in Surface Eddy Current Inspections of Aircraft Structures Catalin Mandache *1, Theodoros Theodoulidis 2 1 Structures, Materials and Manufacturing Laboratory, National

More information

IMAGING OF DEFECTS IN CONCRETE COMPONENTS WITH NON-CONTACT ULTRASONIC TESTING W. Hillger, DLR and Ing. Büro Dr. Hillger, Braunschweig, Germany

IMAGING OF DEFECTS IN CONCRETE COMPONENTS WITH NON-CONTACT ULTRASONIC TESTING W. Hillger, DLR and Ing. Büro Dr. Hillger, Braunschweig, Germany IMAGING OF DEFECTS IN CONCRETE COMPONENTS WITH NON-CONTACT ULTRASONIC TESTING W. Hillger, DLR and Ing. Büro Dr. Hillger, Braunschweig, Germany Abstract: The building industries require NDT- methods for

More information

Depth of Penetration Effects in Eddy Current Testing

Depth of Penetration Effects in Eddy Current Testing Depth of Penetration Effects in Eddy Current Testing Shiva Majidnia 1, John Rudlin 2 and Ragogapol Nilavalan 3 Brunel University Cambridge CB1 6AL, UK Telephone 01223 899000 Fax 01223 890689 E-mail shiva.majidnia@twi.co.uk

More information

Attenuation dependent detectability at ultrasonic inspection of copper

Attenuation dependent detectability at ultrasonic inspection of copper Public Report Document ID 1411328 Author C. Müller T. Heckel P. Brömel M. Pavlovic U. Ronneteg Reviewed by Version 2.0 Sabina Hammarberg (QA) Approved by Jan Sarnet Status Approved Reg no Date 2014-02-07

More information

AA&S Conference 2018 Eddy Current Array for Aircraft

AA&S Conference 2018 Eddy Current Array for Aircraft AA&S Conference 2018 Eddy Current Array for Aircraft Presented by Graham Maxwell Olympus Australia NDT Key Account Manager Material provided by Ghislain Morais Olympus NDT Canada Eddy Current Array ECA

More information

The Development of Laser Ultrasonic Visualization Equipment and its Application in Nondestructive Inspection

The Development of Laser Ultrasonic Visualization Equipment and its Application in Nondestructive Inspection 17th World Conference on Nondestructive Testing, 25-28 Oct 2008, Shanghai, China The Development of Laser Ultrasonic Visualization Equipment and its Application in Nondestructive Inspection Bo WANG 1,

More information

Magnetic Eddy Current (MEC) Inspection Technique

Magnetic Eddy Current (MEC) Inspection Technique Introduction Eddy Current Testing (ECT) is a well established technology for the inspection of metallic components for surface breaking flaws. It is used for component testing in the aviation and automotive

More information

DEVELOPMENT OF EDDY CURRENT PROBES BASED ON MAGNETORESISTIVE ARRAY SENSORS

DEVELOPMENT OF EDDY CURRENT PROBES BASED ON MAGNETORESISTIVE ARRAY SENSORS DEVELOPMENT OF EDDY CURRENT PROBES BASED ON MAGNETORESISTIVE ARRAY SENSORS N. Sergeeva-Chollet, C.Fermon, J.-M. Decitre, M. Pelkner, V.Reimund, M. Kreutzbruck QNDE, July, 25, 2013 CEA 10 AVRIL 2012 OUTLINE

More information

DETECTION AND SIZING OF SHORT FATIGUE CRACKS EMANATING FROM RIVET HOLES O. Kwon 1 and J.C. Kim 1 1 Inha University, Inchon, Korea

DETECTION AND SIZING OF SHORT FATIGUE CRACKS EMANATING FROM RIVET HOLES O. Kwon 1 and J.C. Kim 1 1 Inha University, Inchon, Korea DETECTION AND SIZING OF SHORT FATIGUE CRACKS EMANATING FROM RIVET HOLES O. Kwon 1 and J.C. Kim 1 1 Inha University, Inchon, Korea Abstract: The initiation and growth of short fatigue cracks in a simulated

More information

A Numerical Study of Depth of Penetration of Eddy Currents

A Numerical Study of Depth of Penetration of Eddy Currents A Numerical Study of Depth of Penetration of Eddy Currents S.Majidnia* a,b, R.Nilavalan b, J. Rudlin a a. TWI Ltd, Cambridge,United Kingdom b Brunel University, London,United Kingdom shiva.majidnia@twi.co.uk

More information

The Application of TOFD Technique on the Large Pressure Vessel

The Application of TOFD Technique on the Large Pressure Vessel 17th World Conference on Nondestructive Testing, 25-28 Oct 2008, Shanghai, China The Application of TOFD Technique on the Large Pressure Vessel Yubao Guangdong Special Equipment Inspection Institute Floor

More information

Application of Ultrasonic Guided Wave to Heat Exchanger Tubes Inspection

Application of Ultrasonic Guided Wave to Heat Exchanger Tubes Inspection 17th World Conference on Nondestructive Testing, 25-28 Oct 2008, Shanghai, China Application of Ultrasonic Guided Wave to Heat Exchanger Tubes Inspection Ik-Keun PARK 1,a, Yong-Kwon KIM 2,b, Sae-Jun PARK

More information

D DAVID PUBLISHING. Eddy Current Test for Detection of Foreign Material using Rotating Probe. 2. Theory. 1. Introduction

D DAVID PUBLISHING. Eddy Current Test for Detection of Foreign Material using Rotating Probe. 2. Theory. 1. Introduction Journal of Mechanics Engineering and Automation 6 (2016) 379-383 doi: 10.17265/2159-5275/2016.07.009 D DAVID PUBLISHING Eddy Current Test for Detection of Foreign Material using Rotating Probe Houng Kun

More information

Generation Laser Scanning Method for Visualizing Ultrasonic Waves Propagating on a 3-D Object

Generation Laser Scanning Method for Visualizing Ultrasonic Waves Propagating on a 3-D Object 1st International Symposium on Laser Ultrasonics: Science, Technology and Applications July 16-18 2008, Montreal, Canada Generation Laser Scanning Method for Visualizing Ultrasonic Waves Propagating on

More information

The Battle of Carbon Steel

The Battle of Carbon Steel More info ab The Battle of Carbon Steel Advantages of Eddy Current Array over Magnetic Particle and Penetrant Testing for Inspecting the Surface of Carbon Steel Welds Terence Burke Product Application

More information

Performance of UT Creeping Waves in Crack Sizing

Performance of UT Creeping Waves in Crack Sizing 17th World Conference on Nondestructive Testing, 25-28 Oct 2008, Shanghai, China Performance of UT Creeping Waves in Crack Sizing Michele Carboni, Michele Sangirardi Department of Mechanical Engineering,

More information

A Breakthrough in Sputtering Target Inspections: Ultra-High Speed Phased Array Scanning with Volume Focusing

A Breakthrough in Sputtering Target Inspections: Ultra-High Speed Phased Array Scanning with Volume Focusing 17th World Conference on Nondestructive Testing, 25-28 Oct 2008, Shanghai, China A Breakthrough in Sputtering Target Inspections: Ultra-High Speed Phased Array Scanning with Volume Focusing Dominique Braconnier,

More information

EVOLUTION OF THE CRYOGENIC EDDY CURRENT MICROPROBE

EVOLUTION OF THE CRYOGENIC EDDY CURRENT MICROPROBE EVOLUTION OF THE CRYOGENIC EDDY CURRENT MICROPROBE J.L. Fisher, S.N. Rowland, J.S. Stolte, and Keith S. Pickens Southwest Research Institute 6220 Culebra Road San Antonio, TX 78228-0510 INTRODUCTION In

More information

Rock Bolt Inspection by Means of RBT Instrument

Rock Bolt Inspection by Means of RBT Instrument 19 th World Conference on Non-Destructive Testing 2016 Rock Bolt Inspection by Means of RBT Instrument Tadeusz STEPINSKI 1, Karl-Johan MATSSON 2 1 AGH University of Science and Technology, Krakow, Poland

More information

Eddy current flaw detector «Eddycon C»

Eddy current flaw detector «Eddycon C» ULTRACON-SERVICE LLC Eddy current flaw detector «Eddycon C» Quick start guide CONTENTS P. 1 CONTROLLERS OF EDDYCON C FLAW DETECTOR... 3 2 SETTINGS OF «TEST» MENU... 5 3 INSTRUCTIONS FOR USE... 8 3.1 THRESHOLD

More information

New Instrument for Rock Bolt Inspection Using Guided Waves

New Instrument for Rock Bolt Inspection Using Guided Waves 11th European Conference on Non-Destructive Testing (ECNDT 2014), October 6-10, 2014, Prague, Czech Republic New Instrument for Rock Bolt Inspection Using Guided Waves More Info at Open Access Database

More information

MultiScan MS Tube Inspection System. Multi-technology System Eddy Current Magnetic Flux Leakage Remote Field IRIS Ultrasound

MultiScan MS Tube Inspection System. Multi-technology System Eddy Current Magnetic Flux Leakage Remote Field IRIS Ultrasound MultiScan MS 5800 Tube Inspection System Multi-technology System Eddy Current Magnetic Flux Leakage Remote Field IRIS Ultrasound 920-107 MultiScan MS 5800 E Tube Inspection with Eddy Current Condensers

More information

KAERI Feeder Tube Inspection Using EMAT Generated Circumferential Guided Waves

KAERI Feeder Tube Inspection Using EMAT Generated Circumferential Guided Waves Sonic Sensors www.sonicsensors.com 1of 9 KAERI Feeder Tube Inspection Using EMAT Generated Circumferential Guided Waves Objective: Inspection of small diameter pie with complex curves. The principal defects

More information

MultiScan MS Tube Inspection System. Multi-technology System Eddy Current Magnetic Flux Leakage Remote Field IRIS Ultrasound

MultiScan MS Tube Inspection System. Multi-technology System Eddy Current Magnetic Flux Leakage Remote Field IRIS Ultrasound MultiScan MS 5800 Tube Inspection System 920-107 Multi-technology System Eddy Current Magnetic Flux Leakage Remote Field IRIS Ultrasound MultiScan MS 5800 E Tube Inspection with Eddy Current Condensers

More information

Isolation Scanner. Advanced evaluation of wellbore integrity

Isolation Scanner. Advanced evaluation of wellbore integrity Isolation Scanner Advanced evaluation of wellbore integrity Isolation Scanner* cement evaluation service integrates the conventional pulse-echo technique with flexural wave propagation to fully characterize

More information

COMPUTER MODELING OF EDDY CURRENT TRANSMIT-RECEIVE PROBES FOR. S.P. Sullivan, V.S. Cecco, L.S. Obrutsky, D. Humphrey, S.P. Smith and K.A.

COMPUTER MODELING OF EDDY CURRENT TRANSMIT-RECEIVE PROBES FOR. S.P. Sullivan, V.S. Cecco, L.S. Obrutsky, D. Humphrey, S.P. Smith and K.A. COMPUTER MODELING OF EDDY CURRENT TRANSMIT-RECEIVE PROBES FOR TUBE INSPECTION INTRODUCTION S.P. Sullivan, V.S. Cecco, L.S. Obrutsky, D. Humphrey, S.P. Smith and K.A. Emde Nondestructive Testing Development

More information

High-Resolution Corrosion Monitoring for Reliable Assessment of Infrastructure

High-Resolution Corrosion Monitoring for Reliable Assessment of Infrastructure 19 th World Conference on Non-Destructive Testing 2016 High-Resolution Corrosion Monitoring for Reliable Assessment of Infrastructure André Lamarre 1 1 Olympus Scientific Solutions Americas, Quebec City,

More information

Spectral Distance Amplitude Control for Ultrasonic Inspection of Composite Components

Spectral Distance Amplitude Control for Ultrasonic Inspection of Composite Components ECNDT 26 - Mo.2.6.4 Spectral Distance Amplitude Control for Ultrasonic Inspection of Composite Components Uwe PFEIFFER, Wolfgang HILLGER, DLR German Aerospace Center, Braunschweig, Germany Abstract. Ultrasonic

More information

DETECTING DEFECTS by Larry Adams, senior editor. Finding flaws and imperfections in a tube or pipe is made easier using new inspection technologies

DETECTING DEFECTS by Larry Adams, senior editor. Finding flaws and imperfections in a tube or pipe is made easier using new inspection technologies DETECTING DEFECTS by Larry Adams, senior editor Finding flaws and imperfections in a tube or pipe is made easier using new inspection technologies This inspection system is designed to detect flaws on

More information

DEEP FLAW DETECTION WITH GIANT MAGNETORESISTIVE (GMR) BASED SELF-NULLING PROBE

DEEP FLAW DETECTION WITH GIANT MAGNETORESISTIVE (GMR) BASED SELF-NULLING PROBE DEEP FLAW DETECTION WITH GIANT MAGNETORESISTIVE (GMR) BASED SELF-NULLING PROBE Buzz Wincheski and Min Namkung NASA Langley Research Center Hampton, VA 23681 INTRODUCTION The use of giant magnetoresistive

More information

IMPROVEMENT OF DETECTION OF SMALL DEFECTS LOCATED NEAR OR FAR FROM WELDS OF MAGNETIC STEAM GENERATOR TUBES USING REMOTE FIELD EDDY CURRENT

IMPROVEMENT OF DETECTION OF SMALL DEFECTS LOCATED NEAR OR FAR FROM WELDS OF MAGNETIC STEAM GENERATOR TUBES USING REMOTE FIELD EDDY CURRENT 12 th A-PCNDT 2006 Asia-Pacific Conference on NDT, 5 th 10 th Nov 2006, Auckland, New Zealand IMPROVEMENT OF DETECTION OF SMALL DEFECTS LOCATED NEAR OR FAR FROM WELDS OF MAGNETIC STEAM GENERATOR TUBES

More information

EDDYCON C AIRCRAFT SET OF EDDY CURRENT FLAW DETECTOR FOR AIRCRAFTS TESTING. CE MARKING

EDDYCON C AIRCRAFT SET OF EDDY CURRENT FLAW DETECTOR FOR AIRCRAFTS TESTING.  CE MARKING AIRCRAFT SET OF EDDY CURRENT FLAW DETECTOR Member company of «OKO ASSOCIATION» Group EDDYCON C FOR AIRCRAFTS TESTING Surface and subsurface defect detection. Assessment of defect depth. Conductivity measurement.

More information

MULTI CHANNEL EDDY CURRENT FLAW DETECTOR EDDYCON D

MULTI CHANNEL EDDY CURRENT FLAW DETECTOR EDDYCON D MULTI CHANNEL EDDY CURRENT FLAW DETECTOR Member company of «OKO ASSOCIATION» Group THE BEST INDUSTRIAL OEM SOLUTION FOR IN-LINE AND IN-SERVICE SYSTEMS www.oko-ndt.com PURPOSE THE FLAW DETECTOR ADVANTAGES

More information

Basic functions of the universal flaw detector GEKKO

Basic functions of the universal flaw detector GEKKO Product Description GEKKO Portable ultrasonic flaw detector for phased array, TOFD und conventional inspection techniques. Basic functions of the universal flaw detector GEKKO Phased array techniques Phased

More information

Modelling III ABSTRACT

Modelling III ABSTRACT Modelling III Hybrid FE-VIM Model of Eddy Current Inspection of Steam Generator Tubes in the Vicinity of Tube Support Plates S. Paillard, A. Skarlatos, G. Pichenot, CEA LIST, France G. Cattiaux, T. Sollier,

More information

Weld Seam Inspection of Thick Wall Austenitic Steel Tubes beyond Standard Eddy Current Technology

Weld Seam Inspection of Thick Wall Austenitic Steel Tubes beyond Standard Eddy Current Technology Pos: 1 /Technical Info Papers/Weld seam inspection with TMI/Autor bio - Markus Witte @ 3\mod_1178186286475_31.doc @ 16916 Pos: 2 /Technical Info Papers/Weld seam inspection with TMI/Abstract - Remote Field

More information

UNIVERSAL ULTRASONIC FLAW DETECTOR UD4-76. TOFD version.

UNIVERSAL ULTRASONIC FLAW DETECTOR UD4-76. TOFD version. UNIVERSAL ULTRASONIC FLAW DETECTOR UD4-76 TOFD version www.ndt.com.ua PURSPOSE UD4-76 universal ultrasonic flaw detector-tomograph with large high-contrast TFT display is intended for products testing

More information

Introduction To NDT. BY: Omid HEIDARY

Introduction To NDT. BY: Omid HEIDARY Introduction To NDT BY: Omid HEIDARY NDT Methods Penetrant Testing Magnetic Particle Testing Eddy Current Testing Ultrasonic Testing Radiographic Testing Acoustic Emission Infrared Testing Visual Testing

More information

Phased Array UT Application For Boiler Tube Inspection in Manufacturing And In-Service Anandamurugan S 1, Siva Sankar Y 2

Phased Array UT Application For Boiler Tube Inspection in Manufacturing And In-Service Anandamurugan S 1, Siva Sankar Y 2 More Info at Open Access Database www.ndt.net/?id=15156 Phased Array UT Application For Boiler Tube Inspection in Manufacturing And In-Service Anandamurugan S 1, Siva Sankar Y 2 1 GE Inspection Technologies,

More information

Heat Exchanger & Boiler Tube Inspection Techniques

Heat Exchanger & Boiler Tube Inspection Techniques Overview For the in-service inspection of ferromagnetic, non-ferromagnetic and fin-fan tubes, the following advanced techniques offer high defect detection capabilities and accurate defect analysis: Multiple

More information

INSPECTION OF THERMAL BARRIERS OF PRIMARY PUMPS WITH PHASED ARRAY PROBE AND PIEZOCOMPOSITE TECHNOLOGY

INSPECTION OF THERMAL BARRIERS OF PRIMARY PUMPS WITH PHASED ARRAY PROBE AND PIEZOCOMPOSITE TECHNOLOGY INSPECTION OF THERMAL BARRIERS OF PRIMARY PUMPS WITH PHASED ARRAY PROBE AND PIEZOCOMPOSITE TECHNOLOGY J. Poguet Imasonic S.A. France E. Abittan EDF-GDL France Abstract In order to meet the requirements

More information

J. L. Fisher, S. N. Rowland, F. A. Balter, S. S. Stolte, and Keith S. Pickens. Southwest Research Institute 6220 Culebra Road San Antonio, TX 78284

J. L. Fisher, S. N. Rowland, F. A. Balter, S. S. Stolte, and Keith S. Pickens. Southwest Research Institute 6220 Culebra Road San Antonio, TX 78284 A CRYOGENIC EDDY CURRENT MICROPROBE J. L. Fisher, S. N. Rowland, F. A. Balter, S. S. Stolte, and Keith S. Pickens Southwest Research Institute 6220 Culebra Road San Antonio, TX 78284 INTRODUCTION In nondestructive

More information

ADVANCED COMBINATION PROBE FOR TESTING FERRITIC SEA-CURE CONDENSER TUBING

ADVANCED COMBINATION PROBE FOR TESTING FERRITIC SEA-CURE CONDENSER TUBING ADVANCED COMBINATION PROBE FOR TESTING FERRITIC SEA-CURE CONDENSER TUBING Kenji Krzywosz, Electric Power Research Institute (EPRI), Daniel Folsom, Tennessee Valley Authority (TVA), USA ABSTRACT As more

More information

EDDY CURRENT INSPECTION FOR DEEP CRACK DETECTION AROUND FASTENER HOLES IN AIRPLANE MULTI-LAYERED STRUCTURES

EDDY CURRENT INSPECTION FOR DEEP CRACK DETECTION AROUND FASTENER HOLES IN AIRPLANE MULTI-LAYERED STRUCTURES EDDY CURRENT INSPECTION FOR DEEP CRACK DETECTION AROUND FASTENER HOLES IN AIRPLANE MULTI-LAYERED STRUCTURES Teodor Dogaru Albany Instruments Inc., Charlotte, NC tdogaru@hotmail.com Stuart T. Smith Center

More information

PORTABLE EDDY CURRENT FLAW DETECTOR VD3-71 NK-IVU.

PORTABLE EDDY CURRENT FLAW DETECTOR VD3-71 NK-IVU. PORTABLE EDDY CURRENT FLAW DETECTOR VD3-71 NK-IVU www.ndt.com.ua PURPOSE FLAW DETECTOR ADVANTAGES VD3-71 eddy current flaw detector is rated among the means of flaw detectors testing and evaluation and

More information

Effect of fatigue crack orientation on the sensitivity of eddy current inspection in martensitic stainless steels

Effect of fatigue crack orientation on the sensitivity of eddy current inspection in martensitic stainless steels Effect of fatigue crack orientation on the sensitivity of eddy current inspection in martensitic stainless steels Hamid Habibzadeh Boukani, Ehsan Mohseni, Martin Viens Département de Génie Mécanique, École

More information

Table 1 The wheel-set security system of China high-speed railway

Table 1 The wheel-set security system of China high-speed railway 11th European Conference on Non-Destructive Testing (ECNDT 2014), October 6-10, 2014, Prague, Czech Republic More Info at Open Access Database www.ndt.net/?id=16352 Dynamic ultrasonic inspection technology

More information

Application of Guided Wave Technology to Tube Inspection

Application of Guided Wave Technology to Tube Inspection ECNDT 2006 - Th.3.1.5 Application of Guided Wave Technology to Tube Inspection T. VOGT, D. ALLEYNE, B. PAVLAKOVIC, Guided Ultrasonics Limited, Nottingham, United Kingdom 1. Introduction Abstract. The inspection

More information

Pipeline Technology Conference 2010

Pipeline Technology Conference 2010 THRESHOLDS, ACCURACIES AND RESOLUTION: QUANTITATIVE MEASUREMENT AND ITS ADVANTAGES FOR METAL LOSS INSPECTION A. Barbian, M. Beller, A. Hugger, C. Jäger, A. Pfanger NDT Systems & Services Stutensee, Germany

More information

Detecting 1 st and 2 nd Layer Simulated Cracks in Aircraft Wing Spanwise Splice Standards Using Remote-Field Eddy Current Technique

Detecting 1 st and 2 nd Layer Simulated Cracks in Aircraft Wing Spanwise Splice Standards Using Remote-Field Eddy Current Technique Detecting 1 st and Layer imulated Cracks in Aircraft Wing panwise plice tandards Using Remote-Field Eddy Current Technique Yushi un, Tianhe Ouyang Innovative Materials Testing Technologies, Inc. 251 N.

More information

1. Introduction. 2. Mobile Ultrasonic Inspection System MUSE

1. Introduction. 2. Mobile Ultrasonic Inspection System MUSE 15th World Conference on Nondestructive Testing Roma (Italy) 15-21 October 2000 Proceedings on CD-ROM Ultrasonic Testing of Composites from Laboratory Research to Field Inspections W. Hillger DLR Braunschweig,

More information

Developments in Electromagnetic Inspection Methods I

Developments in Electromagnetic Inspection Methods I 6th International Conference on NDE in Relation to Structural Integrity for Nuclear and Pressurized Components October 2007, Budapest, Hungary For more papers of this publication click: www.ndt.net/search/docs.php3?mainsource=70

More information

INDUSTRIAL APPLICATIONS OF AIR-COUPLED ULTRASONIC TECHNIQUE

INDUSTRIAL APPLICATIONS OF AIR-COUPLED ULTRASONIC TECHNIQUE 7 th International Symposium on NDT in Aerospace We.2.A.3 More Info at Open Access Database www.ndt.net/?id=18954 INDUSTRIAL APPLICATIONS OF AIR-COUPLED ULTRASONIC TECHNIQUE Wolfgang HILLGER 1, Detlef

More information

Hybrid of Eddy Current Probe Based on Permanent Magnet and GMR Sensor

Hybrid of Eddy Current Probe Based on Permanent Magnet and GMR Sensor Hybrid of Eddy Current Probe Based on Permanent Magnet and GMR Sensor Moneer A Faraj 1, Fahmi Samsuri 1, Ahmed N AbdAlla 2 1 Faculty of Electrical and Electronics, University Malaysia Pahang, Malaysia

More information

ECNDT We.2.6.4

ECNDT We.2.6.4 ECNDT 006 - We..6.4 Towards Material Characterization and Thickness Measurements using Pulsed Eddy Currents implemented with an Improved Giant Magneto Resistance Magnetometer V. O. DE HAAN, BonPhysics

More information

DACON INSPECTION SERVICES. Phased Array Ultrasonic Testing

DACON INSPECTION SERVICES. Phased Array Ultrasonic Testing Phased Array Ultrasonic Testing Who we are Conventional and Advanced NDT and Inspection Services Oil and Gas, Refinery, Petrochemical, Heavy Industry, Mining Over 400 personnel including more than 300

More information

High Resolution Inspection of Carbon Fiber Materials by Eddy Current Techniques

High Resolution Inspection of Carbon Fiber Materials by Eddy Current Techniques 2nd International Symposium on NDT in Aerospace 2010 - Mo.2.A.3 High Resolution Inspection of Carbon Fiber Materials by Eddy Current Techniques Henning HEUER, Martin H. SCHULZE, Norbert MEYENDORF a Fraunhofer

More information

EDDY CURRENT INSPECTION MODELLING OF THE ELBOW OF A STEAM GENERATOR TUBE WITH THE FINITE ELEMENT SOFTWARE «FLUX»

EDDY CURRENT INSPECTION MODELLING OF THE ELBOW OF A STEAM GENERATOR TUBE WITH THE FINITE ELEMENT SOFTWARE «FLUX» EDDY CURRENT INSPECTION MODELLING OF THE ELBOW OF A STEAM GENERATOR TUBE WITH THE FINITE ELEMENT SOFTWARE «FLUX» Fabrice FOUCHER*, Bastien LAVIE**, Erwan TOUDIC** * EXTENDE, 86 rue de Paris, 91400 ORSAY,

More information

Microwave Based Non-Destructive Testing using Modified Eddy Current Systems

Microwave Based Non-Destructive Testing using Modified Eddy Current Systems ECNDT 2006 - Tu.1.8.4 Microwave Based Non-Destructive Testing using Modified Eddy Current Systems Dirk BEILKEN, Hochschule Magdeburg-Stendal (FH) University of Applied Sciences, Magdeburg, Germany Johann

More information

DEVELOPMENT OF A PROBE OF EDDY CURRENT TESTING FOR DETECTION OF IN-PLANE WAVINESS IN CFRP CROSS-PLY LAMINATES

DEVELOPMENT OF A PROBE OF EDDY CURRENT TESTING FOR DETECTION OF IN-PLANE WAVINESS IN CFRP CROSS-PLY LAMINATES 7 th International Symposium on NDT in Aerospace Tu.1.A.7 DEVELOPMENT OF A PROBE OF EDDY CURRENT TESTING FOR DETECTION OF IN-PLANE WAVINESS IN CFRP CROSS-PLY LAMINATES Koichi MIZUKAMI 1, Yoshihiro MIZUTANI

More information

CIRCULAR PHASED ARRAY PROBES FOR INSPECTION OF SUPERPHOENIX STEAM GENERATOR TUBES

CIRCULAR PHASED ARRAY PROBES FOR INSPECTION OF SUPERPHOENIX STEAM GENERATOR TUBES CIRCULAR PHASED ARRAY PROBES FOR INSPECTION OF SUPERPHOENIX STEAM GENERATOR TUBES G. Fleury, J. Poguet Imasonic S.A. France O. Burat, G Moreau Framatome France Abstract An ultrasonic Phased Array system

More information

Eddy Current Nondestructive Evaluation Based on Fluxgate Magnetometry Umberto Principio Sponsored by: INFM

Eddy Current Nondestructive Evaluation Based on Fluxgate Magnetometry Umberto Principio Sponsored by: INFM 67 Eddy Current Nondestructive Evaluation Based on Fluxgate Magnetometry Umberto Principio Sponsored by: INFM Introduction Eddy current (EC) nondestructive evaluation (NDE) consists in the use of electromagnetic

More information

Dave Stubbs, Wally Hoppe, and Bob Olding. NDE Systems Division Systems Research Laboratories, Inc. Dayton, Ohio

Dave Stubbs, Wally Hoppe, and Bob Olding. NDE Systems Division Systems Research Laboratories, Inc. Dayton, Ohio AUTOMATIC EDDY CURRENT HOLE CENTERING FOR AIRCRAFT ENGINE COMPONENTS Dave Stubbs, Wally Hoppe, and Bob Olding NDE Systems Division Systems Research Laboratories, Inc. Dayton, Ohio 4544-4696 INTRODUCTION

More information

Predator Probe Theory and Operation

Predator Probe Theory and Operation Predator Probe Theory and Operation VM Products, Inc. Specialists in Eddy Current Probes, Reference Standards, Applications, Research & Development P.O. Box 44926, Tacoma, WA 98444 Tel: (253) 841-2939

More information

REAL TIME SURFACE DEFORMATIONS MONITORING DURING LASER PROCESSING

REAL TIME SURFACE DEFORMATIONS MONITORING DURING LASER PROCESSING The 8 th International Conference of the Slovenian Society for Non-Destructive Testing»Application of Contemporary Non-Destructive Testing in Engineering«September 1-3, 2005, Portorož, Slovenia, pp. 335-339

More information

2010 ULTRASONIC BENCHMARKS

2010 ULTRASONIC BENCHMARKS World Federation of N D 2010 ULTRASONIC BENCHMARKS E Centers Problems for 2010 This year for the ultrasonic benchmark we have some extensive results of tests performed on a planar block containing surface

More information

Optimized Semi-Flexible Matrix Array Probes for Large Rotor Shafts and DGS Sizing Diagram Simulation Tool

Optimized Semi-Flexible Matrix Array Probes for Large Rotor Shafts and DGS Sizing Diagram Simulation Tool 19 th World Conference on Non-Destructive Testing 2016 Optimized Semi-Flexible Matrix Array Probes for Large Rotor Shafts and DGS Sizing Diagram Simulation Tool Dany DEVOS 1, Guy MAES 1, Patrick TREMBLAY

More information

Time Reversal FEM Modelling in Thin Aluminium Plates for Defects Detection

Time Reversal FEM Modelling in Thin Aluminium Plates for Defects Detection ECNDT - Poster 39 Time Reversal FEM Modelling in Thin Aluminium Plates for Defects Detection Yago GÓMEZ-ULLATE, Instituto de Acústica CSIC, Madrid, Spain Francisco MONTERO DE ESPINOSA, Instituto de Acústica

More information

AFRL-RX-WP-TP

AFRL-RX-WP-TP AFRL-RX-WP-TP-2008-4046 DEEP DEFECT DETECTION WITHIN THICK MULTILAYER AIRCRAFT STRUCTURES CONTAINING STEEL FASTENERS USING A GIANT-MAGNETO RESISTIVE (GMR) SENSOR (PREPRINT) Ray T. Ko and Gary J. Steffes

More information

1112. Dimensional evaluation of metal discontinuities by geometrical parameters of their patterns on imaging flaw detector monitor

1112. Dimensional evaluation of metal discontinuities by geometrical parameters of their patterns on imaging flaw detector monitor 1112. Dimensional evaluation of metal discontinuities by geometrical parameters of their patterns on imaging flaw detector monitor Samokrutov A. A., Shevaldykin V. G. Closed Joint Stock Company, Scientific

More information

MICROWAVE THICKNESS MEASUREMENTS OF MAGNETIC COATINGS. D.D. Palmer and V.R. Ditton

MICROWAVE THICKNESS MEASUREMENTS OF MAGNETIC COATINGS. D.D. Palmer and V.R. Ditton MICROWAVE THICKNESS MEASUREMENTS OF MAGNETIC COATINGS D.D. Palmer and V.R. Ditton McDonnell Aircraft Company McDonnell Douglas Corporation P.O. Box 516 St. Louis, MO 63166 INTRODUCTION Microwave nondestructive

More information

New Generation of Air-Coupled Ultrasonic Testing

New Generation of Air-Coupled Ultrasonic Testing New Generation of Air-Coupled Ultrasonic Testing World s 1 st Non-Contact Phased-Array Inspection System Company Location SONOTEC US Inc. in New York, USA Sales and Stock Office for Americas SONOTEC GmbH

More information

Frequency Considerations in Air-Coupled Ultrasonic Inspection.

Frequency Considerations in Air-Coupled Ultrasonic Inspection. Frequency Considerations in Air-Coupled Ultrasonic Inspection. Joe Buckley, Sonatest Plc. Milton Keynes, Bucks, MK12 5QQ, England Tel: + 44 1908 316345 Fax: + 441908 321323 joeb@sonatest-plc.com Hanspeter

More information

PORTABLE EDDY CURRENT FLAW DETECTOR

PORTABLE EDDY CURRENT FLAW DETECTOR PORTABLE EDDY CURRENT FLAW DETECTOR Member company of «OKO ASSOCIATION» Group EDDYCON С www.oko-ndt.com DESCRIPTION PURPOSE INDUSTRIAL APPLICATIONS BENEFITS OF EDDYCON C EDDYCON C portable eddy-current

More information

DESIGN & VALIDATION OF A SEMI-FLEXIBLE PAUT PROBE FOR THE MANUFACTURING INSPECTIONS OF LARGE FORGED ROTORS

DESIGN & VALIDATION OF A SEMI-FLEXIBLE PAUT PROBE FOR THE MANUFACTURING INSPECTIONS OF LARGE FORGED ROTORS DESIGN & VALIDATION OF A SEMI-FLEXIBLE PAUT PROBE FOR THE MANUFACTURING INSPECTIONS OF LARGE FORGED ROTORS Patrick Tremblay, Dirk Verspeelt Zetec. Canada ABSTRACT A new generation of nuclear power plants,

More information

Flexible PCB-Based Eddy Current Array Probes for the Inspection of Turbine Components

Flexible PCB-Based Eddy Current Array Probes for the Inspection of Turbine Components Flexible PCB-Based Eddy Current Array Probes for the Inspection of Turbine Components Andre Lamarre - OlympusNDT-Quebec City Canada Benoit Lepage - OlympusNDT-Quebec City-Canada Tommy Bourgelas - OlympusNDT-Quebec

More information

Advances in Carbon Steel Weld Inspection using Tangential Eddy Current Array

Advances in Carbon Steel Weld Inspection using Tangential Eddy Current Array 19 th World Conference on Non-Destructive Testing 2016 Advances in Carbon Steel Weld Inspection using Tangential Eddy Current Array Angelique RAUDE 1, Michael SIROIS 2, Hugo LEMIEUX 2, Joël CREPEAU 2 1

More information

PHASED ARRAYS FOR SMALL DIAMETER, THIN-WALLED PIPING INSPECTIONS

PHASED ARRAYS FOR SMALL DIAMETER, THIN-WALLED PIPING INSPECTIONS PHASED ARRAYS FOR SMALL DIAMETER, THIN-WALLED PIPING INSPECTIONS Michael Moles 1 and Ed Ginzel 2 1. Senior Technology Manager, Olympus NDT, 48 Woerd Avenue, Waltham, MA, USA 02543. Tel: +1 416 831 4428,

More information

Multivariate Regression Algorithm for ID Pit Sizing

Multivariate Regression Algorithm for ID Pit Sizing IV Conferencia Panamericana de END Buenos Aires Octubre 2007 Abstract Multivariate Regression Algorithm for ID Pit Sizing Kenji Krzywosz EPRI NDE Center 1300 West WT Harris Blvd. Charlotte, NC 28262 USA

More information