Touch Sensor Controller

Size: px
Start display at page:

Download "Touch Sensor Controller"

Transcription

1 Touch Sensor Controller

2 Fujitsu Korea 2

3 Touch Sensing a revolution Touch Sensing a revolution in Human Input Device Can replace virtually all mechanical buttons, sliders and turning knobs Create a simple, robust, clean und esthetic design Insolator (Set cover) Touch Pad (copper) PCB TSC C touch : the capacitance induced between finger and touch pad : the constant value of permittivity (Air=1, Glass=10, Acryl=5~10, Rubber=2~3) D: the thickness of the set cover A: the size of the touch pad 3

4 System Overview Parameters are loaded to from MCU to TSC MCU I²C bus N Touch Pads Touch information as interrupt, wake up etc. Typical Applications Single Keys Output information: Which key has been touched MCU no need to process the touch data Advanced sensing (slide, wheel, approximation etc.) Output information Touch strength MCU needs to process the touch data 4

5 How does it work? Main Idea Digital Sensing Impedance includes capacitance, resistance, and inductance Impedance causes delay of capacitor charging time Time delay is measured Digital domain, no AD conversion Differential Signal Internal reference RC circuit Reference time delay can be calibrated Comparison between Input time delay and reference time delay If input time delay is larger than reference time delay by a certain amount touch event occurred No Ground Electrode needed for Touchpad 5

6 How does it work? - Touch Sensing [1] Not Touched [1] Z IN < Z REF α Z IN Z REF [2] Touched [2] Z IN > Z REF Touch pad Z IN Z REF Output Waveform Consistent sensitivity of the touch pad is maintained by setting proper value of α. 6

7 Advantages Extremely Fast Extremely Low Power Extremely Robust Extremely EASY to implement 7

8 Fast and Low Power Extremely FAST Response Time No complex signal processing needed Register programmable, 10 times/sec (100msec) ~ 5,000 times/sec (0.2msec) Allows data management, filtering, etc. Extremely LOW Power Consumption Supply current typical 120 A Active mode, 60 A Idle mode, 0.1 A Sleep mode Perfectly fit to portable products 8

9 Robust and Easy Implementation Extremely Robust Consistent sensitivity through AIC Resistant to outer signal disturbances through differential signal format Water resistant designs possible ESD protected up to 8KV (HBM) / 15KV (set / air) Extremely EASY to Implement One single electrode is sufficient for touch channel Advanced hardware functionality AIC impedance calibration APIS touch filtering High design flexibility Host interface via I²C up to 12 general-purpose IOs Individual channel sensitivity Touch strength output TSC can be either located close to touch pads or on the main PCB Touch pad can be as small as 1mm x 1mm Tuning Board with Tuning Viewer Program available 9

10 Automatic Impedance Calibration AIC (Automatic Impedance Calibration) Maintain consistent sensitivity despite environmental changes temperature, humidity, production tolerance, etc. Initial setup sensitivity Z IN Sensitivity = a Z REF Temperature PCB Humidity Lot External Changes Z IN Z REF Sensitivity = b Z IN Z REF Sensitivity changes with environment changes Sensitivity = c Sensitivity = a Sensitivity = a Sensitivity stays consistent Z IN Z REF Z IN Z REF AIC adapts reference delay line for each sensor individually to keep constant. 10

11 APIS APIS (Adjacent Pattern Interference Suppression) Filter out unintentional touches Reduce Software efforts APIS Mode 1 Reports the strongest output only APIS Mode 2 Reports all outputs that exceeds predefined thresholds APIS Mode 3 Reports two strongest outputs 11

12 Water Resistant Split pad Water Drop C touch Sensor Input Split pad Coupling Capacity between two electrodes is measured Finger increases capacity coupling Water drop has the same effect false touch detection GND Input GND Single pad N Sensor Input Sensing Cap Ref Input Single pad N No ground or reference electrode next to pad Capacity of pad is measured directly Water drop has nearly no effect no false trigger Water Drop 12

13 Tuning/Development Board DPI7 Tuning Kit Main Board Communication Line On /Off Switch 4CH I 2 C Communication Port ROM Select Switch BUZZ Power On /Off Switch USB Cable I 2 C Communication Cable DPI7 Touch Board LCD Bright Control Resistor Test Pin DPI7 Demo Board 16 X2 Display LCD 14

14 G Development Tools 15

15 Tuning Kit Tuning / Development Software 16

16 Applications of Touch Sensors Unlimited Applications ~ limited only by imagination Touch Sensor may REPLACE virtually all MECHANICAL buttons and scrolling knobs with ELECTRONICS. Buttons Slider Circular Scroll Or Navigation Invisible Buttons on LCD (ITO) Aesthetic Design and Higher Product Reliability 17

17 Why TSC? Key Technology Features Lowest Power Consumption Active (120~350uA), Idle (20uA), Sleep (< 0.1uA) Resistant to Water and Noise ~ Differential signal, No GND Fastest Response Time ~ 0.2 msec (5KHz) Wider Dynamic Range for touch No hardware tuning required Higher Sensitivity More sensitive to smaller changes in capacitance (time delay) Commitments to Customers Customer requirements: FPGA proof Close technical/commercial support On-site technical support, prototyping, proof of concept Meet quality and delivery schedule 18

18 Technical Position Architecture Analog Digital Touch Response Time Slow Fast Digisensor S, C, Q, A Single - End Differential Signal Format Small Large As small as 1mm x 1mm Sensing Pad Area 19

19 Strong Point 1. Consumption Current : 1/10 times comparing to competitors - Because of not using analog technology, circuit architecture is very simple. - Active mode : 130, Idle mode : 70, Sleep mode : Response Time : 25 times comparing to competitors - Because it dose not need complex signal processing, can raise the data sampling rate. 10 Current [ma] 1 Q C S x 25 Faster Speed x 10 Less Power ATLab Conversion Frequency [KHz] 20

20 21 6HQVLQJ&DS 6HQVLQJ&DS 6HQVLQJ&DS 6HQVLQJ&DS &WRXFK &WRXFK &WRXFK &WRXFK Strong Point

21 Strong Point Other s Solution Dielectric material C2 C3 Vs GND Equivalent Circuits C1 Sensing pad C1 C1 C2 C3 Vs Not Touched Touched Sensor Input Sensor Input C touch Sensing Cap Ref Input Water Drop Water Drop GND Input GND 22

22 Strong Point Inherently Differential Architecture Immune for External Noises Non-interrupt Touch Operation at active RF Multi-level Capacitance Values Change of Output RF Signal: 3Vp-p swept from 100MHz to 2.4 GHz, Korea MIC Condition Frequency [GHz] 23

23 Strong Point Low Input Impedance Higher ESD Voltage 8KV 6KV HBM: 8KV (Input Sensor) Set: more than 15KV 4KV 2KV Analog Touch Sensor DigiSensor 24

24 Strong Point High Sensitivity 30 ff/step now (x 5 than others), break 1 ff barrier soon. Small sensing area Better resolution Extend to another applications (e.g. proximity sensing, display embedded touch screen) Digital Advantages Following Moore s Law / Insensitive to Foundry/ Technology Low Power & Best for Portable Electronics Longer Battery Lifetime / Touch Wake-up Fast Sampling Less Noise Aliasing / Capable for Signal Conditionings 25

25 Patent Status ¹o tu tu ± tu u j Ÿ i ª tu ± tu ¹o i j u te Ÿ te y } s tu j ª ± v n Ÿ tu j s j s m p m p ¹o i tu u te te y } ªu js tu k mœ«s Œtu tu Ÿ Ÿ Ÿ tu «ª ªs w tu m s ² ² tu Ÿ v v ƒ ««ª ªs v v tu s Ÿ Ÿ tu nt m y s m t y ¹ m y tu y i tu s y ª y i ªs i tu s Ÿ Ÿ tu Ÿ Protected ¹o i i j Ÿ by j s m m ¹o i 33 patents m y y ¹o ¹o i i s tu i s i i tu s ³i ³i stu ª Ÿ Ÿ s Ÿ s m t m t tu ¹o tu ¹o i u j s i i s tu w öº úrm ¹ n s ž Ÿ s Ÿ Ÿ Ÿ s tu s m m y y t s m t tu tu m Ÿ Ÿ v k 26

26 Available TSC Products Product No. of Ch. Matrix of Ch. No. of DIO or LED Interface Operating Voltage LED Control LED Dimming Package Size [mm] 28

27 TSC Product example Available Packages 29

28 Target Applications Home Large Appliance Wash machine, dryer, hob, stove etc. Small Appliance Cooker, microwave oven etc. Consumer devices Remote control, DVD player etc. 30

29 Target Applications Industrial Application examples ---- wherever robust human input device is needed Control panels Medical instruments Test & Measurement Equipments Special vehicle 31

30 Target Applications - Portable devices 32

31 Target applications - office devices And Many More 33

32 Application implementation Function Spec. Hardware Solution Firmware Solution Touch Pad Design (PCB/ITO) MCU Coding Tuning H/W, S/W Finalize register set values and firmware Production Tuning can be done on site during production. 34

33 Typical Implementation example Portable Multimedia Player Exhibited in CES 2006 Currently in mass production For Buttons For Scrolling DCC on touch B/D 35

34 37

QTouch Capacitive Touch Technology Copyright Atmel Atmel Corporation

QTouch Capacitive Touch Technology Copyright Atmel Atmel Corporation QTouch Capacitive Touch Technology 1 2013 Copyright Atmel Atmel Corporation Atmel Industry Presence: Recent Design Wins Industrial Consumer Appliance 2 QTouch - Buttons, Sliders, & Wheels Atmel Touch Solutions

More information

Figure 1. C805193x/92x Capacitive Touch Sense Development Platform

Figure 1. C805193x/92x Capacitive Touch Sense Development Platform CAPACITIVE TOUCH SENSE SOLUTION RELEVANT DEVICES The concepts and example code in this application note are applicable to the following device families: C8051F30x, C8051F31x, C8051F320/1, C8051F33x, C8051F34x,

More information

Capacitive Sensing Interface of QN908x

Capacitive Sensing Interface of QN908x NXP Semiconductors Document Number: AN12190 Application Note Rev. 0, 05/2018 Capacitive Sensing Interface of QN908x Introduction This document details the Capacitive Sensing (CS) interface of QN908x. It

More information

CBM7021 Capacitive Touch Sensor Controller Datasheet Chipsbank Microelectronics Co., Ltd.

CBM7021 Capacitive Touch Sensor Controller Datasheet Chipsbank Microelectronics Co., Ltd. CBM7021 Capacitive Touch Sensor Controller Datasheet Chipsbank Microelectronics Co., Ltd. No. 701 7/F, Building No. 12, Keji Central Road 2, Software Park High Tech Industrial Park, Shenzhen, P.R.China,

More information

AN-1011 APPLICATION NOTE

AN-1011 APPLICATION NOTE AN-111 APPLICATION NOTE One Technology Way P.O. Box 916 Norwood, MA 262-916, U.S.A. Tel: 781.329.47 Fax: 781.461.3113 www.analog.com EMC Protection of the AD715 by Holger Grothe and Mary McCarthy INTRODUCTION

More information

SAM D20 QTouch Robustness Evaluation Kit

SAM D20 QTouch Robustness Evaluation Kit SAM D20 QTouch Robustness Evaluation Kit Part Number: ATSAMD20-QTRDEMO The SAM D20 QTouch Robustness Evaluation kit demonstrates the high capacitive touch performance of the Peripheral Touch Controller

More information

Microchip mtouch Solution Microchip Technology Incorporated. All Rights Reserved. Insert Class Code Here

Microchip mtouch Solution Microchip Technology Incorporated. All Rights Reserved. Insert Class Code Here Microchip mtouch Solution Slide 1 Goal! Understanding advantage of Capacitive Sensor and applications Microchip mtouch Solution A principal of Capacitive Sensor CSM(Cap sensing Module) of PIC16F72x CVD(Cap

More information

FMA1127. Touch Sensor Controller. Overview. Features. Applications

FMA1127. Touch Sensor Controller. Overview. Features. Applications FMA2 Touch Sensor Controller Overview The FMA2 is a low-power, compact, flexible touch sensor controller that converts capacitance generated between the human body and a conductive touch pad to digital

More information

FMA1127DC. Touch Sensor Controller. Overview. Features. Applications

FMA1127DC. Touch Sensor Controller. Overview. Features. Applications Touch Sensor Controller Overview The is a low-power, compact, flexible touch sensor controller that converts capacitance generated between the human body and a conductive touch pad to digital data without

More information

A Comparison Between MIL-STD and Commercial EMC Requirements Part 2. By Vincent W. Greb President, EMC Integrity, Inc.

A Comparison Between MIL-STD and Commercial EMC Requirements Part 2. By Vincent W. Greb President, EMC Integrity, Inc. A Comparison Between MIL-STD and Commercial EMC Requirements Part 2 By Vincent W. Greb President, EMC Integrity, Inc. OVERVIEW Compare and contrast military (i.e., MIL-STD) and commercial EMC immunity

More information

INITIALIZATION AND REGISTER DESCRIPTION

INITIALIZATION AND REGISTER DESCRIPTION Fujitsu Microelectronics Europe Application Note MCU-AN-301000-E-V12 TOUCH SENSOR CONTROLLER FMA1127DC SERIES INITIALIZATION AND REGISTER DESCRIPTION APPLICATION NOTE Chapter 0 Revision History Revision

More information

Feel the Real World. The final haptic feedback design solution

Feel the Real World. The final haptic feedback design solution Feel the Real World The final haptic feedback design solution Touch is. how we interact with... how we feel... how we experience the WORLD. Touch Introduction Touch screens are replacing traditional user

More information

SynthNV - Signal Generator / Power Detector Combo

SynthNV - Signal Generator / Power Detector Combo SynthNV - Signal Generator / Power Detector Combo The Windfreak SynthNV is a 34.4MHz to 4.4GHz software tunable RF signal generator controlled and powered by a PC running Windows XP, Windows 7, or Android

More information

Operation. Displayed channel. Measuring range. Status indication/ remote control Key lock Measuring mode/ time constant. Scale.

Operation. Displayed channel. Measuring range. Status indication/ remote control Key lock Measuring mode/ time constant. Scale. Electronics & Software Type 5080A... Multichannel Laboratory This universal laboratory charge amplifier can be used for force and torque measurements with piezoelectric dynamometers or force plates. Piezoelectric

More information

APPLICATION NOTE. AT11849: QTouch Surface Design Guide. Atmel QTouch. Introduction. Features

APPLICATION NOTE. AT11849: QTouch Surface Design Guide. Atmel QTouch. Introduction. Features APPLICATION NOTE AT11849: QTouch Surface Design Guide Atmel QTouch Introduction User interfaces in consumer products such as wearables, IoT devices, remote controls, and PC/gaming controls are being driven

More information

AN0504 Tag Design with swarm bee LE

AN0504 Tag Design with swarm bee LE AN0504 Tag Design with swarm bee LE 1.4 NA-14-0267-0005-1.4 Document Information Document Title: Document Version: 1.4 Current Date: 2016-05-31 Print Date: 2016-05-31 Document ID: Document Author: Disclaimer

More information

CapSense Sigma-Delta Data Sheet

CapSense Sigma-Delta Data Sheet 1. CapSense Sigma-Delta User Module CapSense Sigma-Delta Data Sheet CSD Copyright 2007-2009 Cypress Semiconductor Corporation. All Rights Reserved. PSoC Blocks API Memory (Bytes) Typical Pins (per Resources

More information

RF and Microwave Test and Design Roadshow 5 Locations across Australia and New Zealand

RF and Microwave Test and Design Roadshow 5 Locations across Australia and New Zealand RF and Microwave Test and Design Roadshow 5 Locations across Australia and New Zealand Advanced VNA Measurements Agenda Overview of the PXIe-5632 Architecture SW Experience Overview of VNA Calibration

More information

MC-1010 Hardware Design Guide

MC-1010 Hardware Design Guide MC-1010 Hardware Design Guide Version 1.0 Date: 2013/12/31 1 General Rules for Design-in In order to obtain good GPS performances, there are some rules which require attentions for using MC-1010 GPS module.

More information

AN310 Energy optimization of a battery-powered device

AN310 Energy optimization of a battery-powered device Energy optimization of a battery-powered device AN 310, May 2018, V 1.0 feedback@keil.com Abstract Optimizing embedded applications for overall efficiency should be an integral part of the development

More information

AN12082 Capacitive Touch Sensor Design

AN12082 Capacitive Touch Sensor Design Rev. 1.0 31 October 2017 Application note Document information Info Keywords Abstract Content LPC845, Cap Touch This application note describes how to design the Capacitive Touch Sensor for the LPC845

More information

Overview of Charge Time Measurement Unit (CTMU)

Overview of Charge Time Measurement Unit (CTMU) Overview of Charge Time Measurement Unit (CTMU) 2008 Microchip Technology Incorporated. All Rights Reserved. An Overview of Charge Time Measurement Unit Slide 1 Welcome to the Overview of Charge Time Measurement

More information

RN-21. Class 1 Bluetooth Module. Applications. Features. Description. Block Diagram. DS-RN21-V2 3/25/2010

RN-21. Class 1 Bluetooth Module. Applications. Features. Description. Block Diagram.   DS-RN21-V2 3/25/2010 RN-21 www.rovingnetworks.com DS-RN21-V2 3/25/2010 Class 1 Bluetooth Module Features Supports Bluetooth 2.1/2.0/1.2/1.1 standards Class1, up to 15dBm(RN21) (100meters) Bluetooth v2.0+edr support Postage

More information

EXTEND YOUR REACH. Copper Mountain Technologies USB VNAs. S-parameter measurement solutions from 9 khz to 110 GHz Measured parameters from S 11

EXTEND YOUR REACH. Copper Mountain Technologies USB VNAs. S-parameter measurement solutions from 9 khz to 110 GHz Measured parameters from S 11 Copper Mountain Technologies USB VNAs S-parameter measurement solutions from 9 khz to 110 GHz Measured parameters from S 11 to S 44 Dynamic range as high as 162 db typ. (1 Hz IF bandwidth) Measurement

More information

HC-12 Wireless Serial Port Communication Module

HC-12 Wireless Serial Port Communication Module HC-12 Wireless Serial Port Communication Module User Manual version 2.3C (updated from v1.1 English and v2.3 Chinese) Product Applications Wireless sensor Community building security Robot wireless control

More information

VDD 0.1 F A1 C1 IN+ IS31AP2145A IN- CTRL GND. Figure 1 Typical Application Circuit (Differential Input)

VDD 0.1 F A1 C1 IN+ IS31AP2145A IN- CTRL GND. Figure 1 Typical Application Circuit (Differential Input) 2.9W@5.0V MONO CLIP-LESS & FILTER-LESS CLASS-D AUDIO POWER AMPLIFIER GENERAL DESCRIPTION The IS3AP245A is a 2.9W@5.0V mono, clip-less, filter-less, high efficiency Class-D audio power amplifier with automatic

More information

XC800 Peripheral Highlights

XC800 Peripheral Highlights XC800 Peripheral Highlights 8-bit microcontrollers July 2008 Industrial and Multimarket Microcontroller AIM MC IMM Agenda Realtime Applications Example Switched Mode Power Supply CC6 Example Current Measurement

More information

Hardware Platforms and Sensors

Hardware Platforms and Sensors Hardware Platforms and Sensors Tom Spink Including material adapted from Bjoern Franke and Michael O Boyle Hardware Platform A hardware platform describes the physical components that go to make up a particular

More information

FAN MHz TinyBoost Regulator with 33V Integrated FET Switch

FAN MHz TinyBoost Regulator with 33V Integrated FET Switch FAN5336 1.5MHz TinyBoost Regulator with 33V Integrated FET Switch Features 1.5MHz Switching Frequency Low Noise Adjustable Output Voltage Up to 1.5A Peak Switch Current Low Shutdown Current:

More information

ILI2117 Capacitive Touch Controller

ILI2117 Capacitive Touch Controller ILI2117 ILI2117 Capacitive Touch Controller Datasheet Version: V1.01 Release Date: SEP. 09,2015 ILI TECHNOLOGY CORP. 8F, No.38, Taiyuan St., Jhubei City, Hsinchu County 302, Taiwan, R.O.C Tel.886-3-5600099;

More information

Low Cost Motor Control Family

Low Cost Motor Control Family Low Cost Motor Control Family 2011 Microchip Technology Incorporated. All Rights Reserved. Comparator with blanking and filtering Slide 1 Welcome to the Low Cost Motor Control Family web seminar. My Name

More information

Analog front-end electronics in beam instrumentation

Analog front-end electronics in beam instrumentation Analog front-end electronics in beam instrumentation Basic instrumentation structure Silicon state of art Sampling state of art Instrumentation trend Comments and example on BPM Future Beam Position Instrumentation

More information

TABLE OF CONTENTS. FT5x06 DATASHEET 1 OVERVIEW TYPICAL APPLICATIONS FUNCTIONAL DESCRIPTION... 1

TABLE OF CONTENTS. FT5x06 DATASHEET 1 OVERVIEW TYPICAL APPLICATIONS FUNCTIONAL DESCRIPTION... 1 True Multi-Touch Capacitive Touch Panel Controller INTRODUCTION The FT5x06 Series ICs are single-chip capacitive touch panel controller ICs with a built-in 8 bit Micro-controller unit (MCU).They adopt

More information

TFT-LCD DC/DC Converter with Integrated Backlight LED Driver

TFT-LCD DC/DC Converter with Integrated Backlight LED Driver TFT-LCD DC/DC Converter with Integrated Backlight LED Driver Description The is a step-up current mode PWM DC/DC converter (Ch-1) built in an internal 1.6A, 0.25Ω power N-channel MOSFET and integrated

More information

Reflectometer Series:

Reflectometer Series: Reflectometer Series: R54, R60 & R140 Vector Network Analyzers Clarke & Severn Electronics Ph +612 9482 1944 Email sales@clarke.com.au BUY NOW - www.cseonline.com.au KEY FEATURES Patent: US 9,291,657 No

More information

MC-1612 Hardware Design Guide

MC-1612 Hardware Design Guide LOCOSYS Technology Inc. MC-1612 Hardware Design Guide Version 1.0 Date: 2013/09/17 LOCOSYS Technology Inc. 1 General Rules for Design-in In order to obtain good GPS performances, there are some rules which

More information

500 khz / 1 MHz Precision LCR Meter Models 894 & 895

500 khz / 1 MHz Precision LCR Meter Models 894 & 895 Data Sheet 500 khz / 1 MHz Precision LCR Meter 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Industry-Leading Performance The

More information

500 khz / 1 MHz Precision LCR Meter Models 894 & 895

500 khz / 1 MHz Precision LCR Meter Models 894 & 895 Data Sheet 500 khz / 1 MHz Precision LCR Meter Industry-Leading Performance The 894 and 895 are high accuracy LCR meters capable of measuring inductance, capacitance, and resistance of components and materials

More information

Preliminary. 4-Channel RTD/4-20 ma Wireless Sensor Node SN24R420-4

Preliminary. 4-Channel RTD/4-20 ma Wireless Sensor Node SN24R420-4 Preliminary - 4 Analog Channel, Battery Powered Wireless Sensor Node - 2 RTD Inputs and 2 4-20 ma Inputs Plus 2 Switch Inputs - Supports 2- and 3-Wire 100 ohm Platinum RTDs - Switch State and Change-of-State

More information

VT-CC2530-Z1 Wireless Module. User Guide

VT-CC2530-Z1 Wireless Module. User Guide Wireless Module User Guide V-CHIP MICROSYSTEMS Co. Ltd Address: Room 612-613, Science and Technology Service Center Building, NO.1, Qilin Road, Nanshan District, Shenzhen, Guangdong TEL:0755-88844812 FAX:0755-22643680

More information

END OF LIFE. Product Specification PE64908 RF- RF+ CMOS Control Driver and ESD. Product Description

END OF LIFE. Product Specification PE64908 RF- RF+ CMOS Control Driver and ESD. Product Description Product Description PE64908 is a DuNE technology-enhanced Digitally Tunable Capacitor (DTC) based on Peregrine s UltraCMOS technology.this highly versatile product supports a wide variety of tuning circuit

More information

PLANAR R54. Vector Reflectometer KEY FEATURES

PLANAR R54. Vector Reflectometer KEY FEATURES PLANAR R54 Vector Reflectometer KEY FEATURES Frequency range: 85 MHz 5.4 GHz Reflection coefficient magnitude and phase, cable loss, DTF Transmission coefficient magnitude when using two reflectometers

More information

TSM Channel Self Calibration Capacitive Touch Sensor SPECIFICATION V1.0

TSM Channel Self Calibration Capacitive Touch Sensor SPECIFICATION V1.0 TSM2 2-Channel Self Calibration Capacitive Touch Sensor SPECIFICATION V.0 Specification TSM2 (2-CH Auto Sensitivity Calibration Capacitive Touch Sensor). General Feature 2-Channel capacitive sensor with

More information

RN-42. Class 2 Bluetooth Module. Features. Description. Applications. Block Diagram. DS-RN42-V1.1 1/12/2010.

RN-42. Class 2 Bluetooth Module. Features. Description. Applications. Block Diagram.   DS-RN42-V1.1 1/12/2010. www.rovingnetworks.com DS-RN42-V1.1 1/12/2010 Class 2 Bluetooth Module Features Fully qualified Bluetooth 2.1/2.0/1.2/1.1 module Bluetooth v2.0+edr support Postage stamp sized form factor, 13.4mm x 25.8

More information

DIO6010 High-Efficiency 1.5MHz, 1A Continuous, 1.5A Peak Output Synchronous Step Down Converter

DIO6010 High-Efficiency 1.5MHz, 1A Continuous, 1.5A Peak Output Synchronous Step Down Converter DIO6010 High-Efficiency 1.5MHz, 1A Continuous, 1.5A Peak Output Synchronous Step Down Converter Rev 1.2 Features Low R DS(ON) for internal switches (top/bottom) 230mΩ/170mΩ, 1.0A 2.5-5.5V input voltage

More information

LABORATORY 4. Palomar College ENGR210 Spring 2017 ASSIGNED: 3/21/17

LABORATORY 4. Palomar College ENGR210 Spring 2017 ASSIGNED: 3/21/17 LABORATORY 4 ASSIGNED: 3/21/17 OBJECTIVE: The purpose of this lab is to evaluate the transient and steady-state circuit response of first order and second order circuits. MINIMUM EQUIPMENT LIST: You will

More information

NXP AN11155 sensor Application note

NXP AN11155 sensor Application note NXP sensor Application note http://www.manuallib.com/nxp/an11155-sensor-application-note.html This document describes design aspects which should be considered for application circuits using NXP capacitive

More information

How to Create a Touchless Slider for Human Interface Applications

How to Create a Touchless Slider for Human Interface Applications How to Create a Touchless Slider for Human Interface Applications By Steve Gerber, Director of Human Interface Products Silicon Laboratories Inc., Austin, TX Introduction Imagine being able to control

More information

Technology in Balance

Technology in Balance Technology in Balance A G1 G2 B Basic Structure Comparison Regular capacitors have two plates or electrodes surrounded by a dielectric material. There is capacitance between the two conductive plates within

More information

VT-CC M Wireless Module. User Guide

VT-CC M Wireless Module. User Guide Wireless Module User Guide V-CHIP MICROSYSTEMS Co. Ltd Address: Room 612-613, Science and Technology Service Center Building, NO.1, Qilin Road, Nanshan District, Shenzhen, Guangdong TEL:0755-88844812 FAX:0755-22643680

More information

Characteristic Sym Notes Minimum Typical Maximum Units Operating Frequency Range MHz Operating Frequency Tolerance khz

Characteristic Sym Notes Minimum Typical Maximum Units Operating Frequency Range MHz Operating Frequency Tolerance khz DEVELOPMENT KIT (Info Click here) 2.4 GHz ZigBee Transceiver Module Small Size, Light Weight, Low Cost Sleep Current less than 3 µa FCC and ETSI Certified for Unlicensed Operation The ZMN2405 2.4 GHz transceiver

More information

NEXT Lab NXM1001. General Description. Feature. Application. Semiconductor Development Group. High Sensitivity 1-CH Capacitive Touch Switch

NEXT Lab NXM1001. General Description. Feature. Application. Semiconductor Development Group. High Sensitivity 1-CH Capacitive Touch Switch Semiconductor Development Group NXM1001 High Sensitivity 1-CH Capacitive Touch Switch General Description The NXM1001 is a auto calibration High sensitivity 1 channel Capacitive touch switch It includes

More information

High Speed Digital Systems Require Advanced Probing Techniques for Logic Analyzer Debug

High Speed Digital Systems Require Advanced Probing Techniques for Logic Analyzer Debug JEDEX 2003 Memory Futures (Track 2) High Speed Digital Systems Require Advanced Probing Techniques for Logic Analyzer Debug Brock J. LaMeres Agilent Technologies Abstract Digital systems are turning out

More information

New Digital Capacitive Isolator Training Guide ISO74xx & ISO75xx

New Digital Capacitive Isolator Training Guide ISO74xx & ISO75xx New Digital Capacitive Isolator Training Guide ISO74xx & ISO75xx Thomas Kugelstadt February 2010 1 Why new Isolators? An important trend in industrial automation is the continual increase in networking

More information

TTP233-CA6 TonTouch TM 1 KEY TOUCH PAD DETECTOR IC GENERAL DESCRIPTION The TTP233-CA6 TonTouch TM is a touch pad detector IC which offers 1 touch key.

TTP233-CA6 TonTouch TM 1 KEY TOUCH PAD DETECTOR IC GENERAL DESCRIPTION The TTP233-CA6 TonTouch TM is a touch pad detector IC which offers 1 touch key. 1 KEY TOUCH PAD DETECTOR C GENERAL DESCRPTON The is a touch pad detector C which offers 1 touch key. The device built-in regulator for touch sensor. Stable sensing method can cover diversity condition.

More information

Product Datasheet P MHz RF Powerharvester Receiver

Product Datasheet P MHz RF Powerharvester Receiver GND GND GND NC NC NC Product Datasheet DESCRIPTION The Powercast P2110 Powerharvester receiver is an RF energy harvesting device that converts RF to DC. Housed in a compact SMD package, the P2110 receiver

More information

AVL-10000T AUDIO VIDEO LINK TRANSMITTER TECHNICAL MANUAL

AVL-10000T AUDIO VIDEO LINK TRANSMITTER TECHNICAL MANUAL AVL-10000T AUDIO VIDEO LINK TRANSMITTER TECHNICAL MANUAL Document : AVL-10000T Version: 1.00 Author: Henry S Date: 25 July 2008 This module contains protection circuitry to guard against damage due to

More information

International Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering. (An ISO 3297: 2007 Certified Organization)

International Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering. (An ISO 3297: 2007 Certified Organization) International Journal of Advanced Research in Electrical, Electronics Device Control Using Intelligent Switch Sreenivas Rao MV *, Basavanna M Associate Professor, Department of Instrumentation Technology,

More information

AN4299. Application note. Introduction

AN4299. Application note. Introduction Application note Guidelines to improve conducted noise robustness on STM32F0 Series, STM32F3 Series, STM32L0 Series and STM32L4 Series touch sensing applications Introduction Different levels of immunity

More information

X2Y versus CM Chokes and PI Filters. Content X2Y Attenuators, LLC

X2Y versus CM Chokes and PI Filters. Content X2Y Attenuators, LLC X2Y versus CM Chokes and PI Filters 1 Common Mode and EMI Most EMI compliance problems are common mode emissions. Only 10 s of uas in external cables are enough to violate EMC standards. 2 Common Mode

More information

TS mA / 1.5MHz Synchronous Buck Converter

TS mA / 1.5MHz Synchronous Buck Converter SOT-25 Pin Definition: 1. EN 2. Ground 3. Switching Output 4. Input 5. Feedback General Description The TS3406 is a high efficiency monolithic synchronous buck regulator using a 1.5MHz constant frequency,

More information

PE Product Specification RF- RF+ CMOS Control Driver and ESD. Product Description. UltraCMOS Digitally Tunable Capacitor (DTC) MHz

PE Product Specification RF- RF+ CMOS Control Driver and ESD. Product Description. UltraCMOS Digitally Tunable Capacitor (DTC) MHz Product Description The PE6494 is a DuNE -enhanced Digitally Tunable Capacitor (DTC) based on Peregrine s UltraCMOS technology. DTC products provide a monolithically integrated impedance tuning solution

More information

RF4463F30 High Power wireless transceiver module

RF4463F30 High Power wireless transceiver module RF4463F30 High Power wireless transceiver module 1. Description RF4463F30 adopts Silicon Lab Si4463 RF chip, which is a highly integrated wireless ISM band transceiver chip. Extremely high receive sensitivity

More information

EL7302. Hardware Design Guide

EL7302. Hardware Design Guide Hardware Design Guide Version: Preliminary 0.0 Date: January. 2005 Approval: Etron technology, Inc P.O. Box 19-54 No.6 Technology Road V. Science-based Industrial Park, Hsinchu,30077 Taiwan, R.O.C. Tel:

More information

WaveLink High Bandwidth Differential Probing System (16 GHz 25 GHz)

WaveLink High Bandwidth Differential Probing System (16 GHz 25 GHz) WaveLink High Bandwidth Differential Probing System (16 GHz 25 GHz) 25 GHz Solder-In Lead Ultra-compact Browser Superior Probe Impedance Superior Noise Performance EXCEPTIONAL BANDWIDTH AND SIGNAL FIDELITY

More information

AN Extended Range Proximity with SMSC RightTouch Capacitive Sensors

AN Extended Range Proximity with SMSC RightTouch Capacitive Sensors AN 24.19 Extended Range Proximity with SMSC RightTouch Capacitive Sensors 1 Overview 2 Audience 3 References SMSC s RightTouch 1 capacitive sensor family provides exceptional touch interfaces, and now

More information

Low Power Microphone Acquisition and Processing for Always-on Applications Based on Microcontrollers

Low Power Microphone Acquisition and Processing for Always-on Applications Based on Microcontrollers Low Power Microphone Acquisition and Processing for Always-on Applications Based on Microcontrollers Architecture I: standalone µc Microphone Microcontroller User Output Microcontroller used to implement

More information

Characteristic Sym Notes Minimum Typical Maximum Units Operating Frequency Range MHz Operating Frequency Tolerance khz

Characteristic Sym Notes Minimum Typical Maximum Units Operating Frequency Range MHz Operating Frequency Tolerance khz DEVELOPMENT KIT (Info Click here) 2.4 GHz ZigBee Transceiver Module Small Size, Light Weight, +18 dbm Transmitter Power Sleep Current less than 3 µa FCC and ETSI Certified for Unlicensed Operation The

More information

HV BOARDS and MUMETAL Integration. Claudio Arnaboldi Tito Bellunato Emanuele Panzeri Gianluigi Pessina (*) INFN Milano Bicocca

HV BOARDS and MUMETAL Integration. Claudio Arnaboldi Tito Bellunato Emanuele Panzeri Gianluigi Pessina (*) INFN Milano Bicocca HV BOARDS and MUMETAL Integration Claudio Arnaboldi Tito Bellunato Emanuele Panzeri Gianluigi Pessina (*) INFN Milano Bicocca 1 HV BOARDS and Magnetic field SHIELDING The magnetic field must be shielded.

More information

CapSense Sigma-Delta Plus ADC Data Sheet

CapSense Sigma-Delta Plus ADC Data Sheet 1. CapSense Sigma-Delta Plus ADC User Module CapSense Sigma-Delta Plus ADC Data Sheet Copyright 2008-2009 Cypress Semiconductor Corporation. All Rights Reserved. CSDADC PSoC Blocks API Memory (Bytes) Typical

More information

LDS8710. High Efficiency 10 LED Driver With No External Schottky FEATURES APPLICATION DESCRIPTION TYPICAL APPLICATION CIRCUIT

LDS8710. High Efficiency 10 LED Driver With No External Schottky FEATURES APPLICATION DESCRIPTION TYPICAL APPLICATION CIRCUIT High Efficiency 10 LED Driver With No External Schottky FEATURES High efficiency boost converter with the input voltage range from 2.7 to 5.5 V No external Schottky Required (Internal synchronous rectifier*)

More information

HMC540SLP3E v db LSB SILICON MMIC 4-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, GHz

HMC540SLP3E v db LSB SILICON MMIC 4-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, GHz HMC54SLP3E v.95 LSB SILICON MMIC 4-BIT DIGITAL POSITIVE CONTROL ATTENUATOR,. - 8 GHz Typical Applications Features The HMC54SLP3E is ideal for both RF and IF applications: Cellular Infrastructure Wireless

More information

MEMS Ultra-Low Power Oscillator, khz Quartz XTAL Replacement

MEMS Ultra-Low Power Oscillator, khz Quartz XTAL Replacement 33Features: MEMS Technology Small SMD package: 2.0 x 1.2 mm (2012) Fixed 32.768 khz output frequency NanoDrve TM programmable output swing for lowest power Pb-free, RoHS and REACH compliant Typical Applications:

More information

National Instruments Switches

National Instruments Switches ni.com National Instruments Switches Raviteja Chivukula Webinar Overview A. Switch Basics A. Recap B. Advanced Switch Topics A. High Channel Switches B. Fault Insertion Units C. Resistor Modules D. RF

More information

DISCONTINUED. Modulation Type Number of RF Channels 15

DISCONTINUED. Modulation Type Number of RF Channels 15 RFM products are now Murata Products 2.4 GHz Spread Spectrum Transceiver Module Small Size, Light Weight, Low Cost Sleep Current less than 3 µa FCC, Canadian IC and ETSI Certified for Unlicensed Operation

More information

U1571A Ni-MH Battery Pack for U1600A Handheld Oscilloscopes

U1571A Ni-MH Battery Pack for U1600A Handheld Oscilloscopes United States Home >... > Oscilloscope Accessories > U1600 Series Oscilloscope Accessories > U1571A Ni-MH Battery Pack for U1600A Handheld Oscilloscopes Key Specifications Features Ni-MH Battery Pack,

More information

Data Sheet. APDS-9702 Signal Conditioning IC for Optical Proximity Sensors with Digital I 2 C Interface. Features. Description.

Data Sheet. APDS-9702 Signal Conditioning IC for Optical Proximity Sensors with Digital I 2 C Interface. Features. Description. APDS-9702 Signal Conditioning IC for Optical Proximity Sensors with Digital I 2 C Interface Data Sheet Description APDS-9702 is a signal conditioning IC that enhances the performance and robustness of

More information

Overview of EMC Regulations and Testing. Prof. Tzong-Lin Wu Department of Electrical Engineering National Taiwan University

Overview of EMC Regulations and Testing. Prof. Tzong-Lin Wu Department of Electrical Engineering National Taiwan University Overview of EMC Regulations and Testing Prof. Tzong-Lin Wu Department of Electrical Engineering National Taiwan University What is EMC Electro-Magnetic Compatibility ( 電磁相容 ) EMC EMI (Interference) Conducted

More information

P331-2 set ESD generator (IEC )

P331-2 set ESD generator (IEC ) User manual Probe set set ESD generator (IEC 61000-4-2) Copyright January 2017 LANGER GmbH 2017.01.09 User manual Table of contents: Page 1 ESD generator (IEC 61000-4-2) 3 1.1 Design and function of the

More information

Features OBSOLETE. = +25 C, Vcc1 = Vcc2 = +5V

Features OBSOLETE. = +25 C, Vcc1 = Vcc2 = +5V v3.121.1-15 GHz LOW NOISE PROGRAMMABLE DIVIDER (N = 1, 2,, 8) Typical Applications The is ideal for: Satellite Communication Systems Point-to-Point & Point-to-Multi-Point Radios Military Applications Test

More information

ADQ214. Datasheet. Features. Introduction. Applications. Software support. ADQ Development Kit. Ordering information

ADQ214. Datasheet. Features. Introduction. Applications. Software support. ADQ Development Kit. Ordering information ADQ214 is a dual channel high speed digitizer. The ADQ214 has outstanding dynamic performance from a combination of high bandwidth and high dynamic range, which enables demanding measurements such as RF/IF

More information

SNIOT702 Specification. Version number:v 1.0.1

SNIOT702 Specification. Version number:v 1.0.1 Version number:v 1.0.1 Catelog 1 Product introduction... 1 1.1 Product introduction... 1 1.2 Product application... 1 1.3 Main characteristics... 2 1.4 Product advantage... 3 2 Technical specifications...

More information

MS8891A. Application Note. 1 General product description. 2 Introduction to capacitive sensing

MS8891A. Application Note. 1 General product description. 2 Introduction to capacitive sensing Application Note 1 General product description The integrated circuit MS8891A is an ultra-low power two channel capacitive sensor specially designed for human body detection. It offers two operating modes:

More information

RN-41-SM. Class 1 Bluetooth Socket Module. Features. Applications. Description. Block Diagram. rn-41sm-ds 9/9/2009

RN-41-SM. Class 1 Bluetooth Socket Module. Features. Applications. Description. Block Diagram.   rn-41sm-ds 9/9/2009 RN-41-SM www.rovingnetworks.com rn-41sm-ds 9/9/2009 Class 1 Bluetooth Socket Module Features Socket module 3/5V DC TTL I/O Fully qualified Bluetooth 2.1/2.0/1.2/1.1 module Bluetooth v2.0+edr support Low

More information

Capacitive Touch Sensor Design Guide

Capacitive Touch Sensor Design Guide Capacitive Touch Sensor Design Guide Introduction Author: Feargal Cleary, Microchip Technology Inc. The process for designing products that use touch controls is a complex process with many decisions to

More information

Top Ten EMC Problems

Top Ten EMC Problems Top Ten EMC Problems presented by: Kenneth Wyatt Sr. EMC Consultant EMC & RF Design, Troubleshooting, Consulting & Training 10 Northern Boulevard, Suite 1 Amherst, New Hampshire 03031 +1 603 578 1842 www.silent-solutions.com

More information

Top View (Near-side) Side View Bottom View (Far-side) .89±.08. 4x.280. Orientation Marker Orientation Marker.

Top View (Near-side) Side View Bottom View (Far-side) .89±.08. 4x.280. Orientation Marker Orientation Marker. Model B2F2AHF Ultra Low Profile 168 Balun Ω to 2Ω Balanced Description The B2F2AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential input locations on data conversion

More information

CX3300 Series Device Current Waveform Analyzer

CX3300 Series Device Current Waveform Analyzer APPLICATION NOTE CX3300 Series Device Current Waveform Analyzer 7 Hints for Precise Current Measurements The CX3300 series of Device Current Waveform Analyzers can visualize wideband low-level, previously

More information

Electronics Design Laboratory Lecture #10. ECEN 2270 Electronics Design Laboratory

Electronics Design Laboratory Lecture #10. ECEN 2270 Electronics Design Laboratory Electronics Design Laboratory Lecture #10 Electronics Design Laboratory 1 Lessons from Experiment 4 Code debugging: use print statements and serial monitor window Circuit debugging: Re check operation

More information

U1604A Handheld Oscilloscopes, 40 MHz

U1604A Handheld Oscilloscopes, 40 MHz Products & Services Technical Support Buy Industries About Agilent Search: All Test & Measurement Go United States Home >... > Oscilloscopes > U1600A Series handheld oscilloscopes (2 models) > U1604A Handheld

More information

RFIC Group Semester and Diploma Projects

RFIC Group Semester and Diploma Projects RFIC Group Semester and Diploma Projects 1. Fully Implantable Remotely Powered Sensor System for Biomedical Monitoring System This project focuses on the design of a fully implantable, remotely powered

More information

INTREPID Model 336 Digital Microwave Link

INTREPID Model 336 Digital Microwave Link Southwest Microwave, Inc. 9055 S. McKemy Street Tempe, Arizona 85284 USA +1(480) 783-0201 Fax +1(480) 783-0401 Product Specifications INTREPID Model 336 Digital Microwave Link Purpose of document This

More information

Bridge Measurement Systems

Bridge Measurement Systems Section 5 Outline Introduction to Bridge Sensors Circuits for Bridge Sensors A real design: the ADS1232REF The ADS1232REF Firmware This presentation gives an overview of data acquisition for bridge sensors.

More information

ST Wireless Charging Solutions

ST Wireless Charging Solutions ST Wireless Charging Solutions Youth Tan STMicroelectronics Agenda 22 Inductive wireless charging concept Qi and other standards STWBC & STWLC products Focus on 15W platform Customer support Agenda 3 Inductive

More information

EEPROM-Programmable TFT VCOM Calibrator

EEPROM-Programmable TFT VCOM Calibrator 19-2911 Rev 3; 8/6 EVALUATION KIT AVAILABLE EEPROM-Programmable TFT Calibrator General Description The is a programmable -adjustment solution for thin-film transistor (TFT) liquid-crystal displays (LCDs).

More information

WT11I DESIGN GUIDE. Monday, 28 November Version 1.1

WT11I DESIGN GUIDE. Monday, 28 November Version 1.1 WT11I DESIGN GUIDE Monday, 28 November 2011 Version 1.1 Contents: WT11i... 1 Design Guide... 1 1 INTRODUCTION... 5 2 TYPICAL EMC PROBLEMS WITH BLUETOOTH... 6 2.1 Radiated Emissions... 6 2.2 RF Noise in

More information

VTech R&D Design Support Capability

VTech R&D Design Support Capability VTech R&D Design Support Capability VTech Communication Ltd [CMS] Prepared by: YF Poon Date: Nov 2016 1 Design Capabilities R&D Design Services Electronic (both HW & SW Design) Schematic and PCB Layout

More information

SD8000S. 20 bits ADC SOC with RTC. SD8000S Bare Die. Features. Applications. Description. Ordering Information. Pin Diagram and Descriptions

SD8000S. 20 bits ADC SOC with RTC. SD8000S Bare Die. Features. Applications. Description. Ordering Information. Pin Diagram and Descriptions 20 bits ADC SOC with RTC Features High precision ADC, 20 bits effective resolution Low noise, high input impedance preamplifier with selectable gain: 1, 12.5, 50, 100, or 200 8 bits RISC ultra low power

More information

Using the VM1010 Wake-on-Sound Microphone and ZeroPower Listening TM Technology

Using the VM1010 Wake-on-Sound Microphone and ZeroPower Listening TM Technology Using the VM1010 Wake-on-Sound Microphone and ZeroPower Listening TM Technology Rev1.0 Author: Tung Shen Chew Contents 1 Introduction... 4 1.1 Always-on voice-control is (almost) everywhere... 4 1.2 Introducing

More information

7. EMV Fachtagung. EMV-gerechtes Filterdesign. 23. April 2009, TU-Graz. Dr. Gunter Winkler (TU Graz) Dr. Bernd Deutschmann (Infineon Technologies AG)

7. EMV Fachtagung. EMV-gerechtes Filterdesign. 23. April 2009, TU-Graz. Dr. Gunter Winkler (TU Graz) Dr. Bernd Deutschmann (Infineon Technologies AG) 7. EMV Fachtagung 23. April 2009, TU-Graz EMV-gerechtes Filterdesign Dr. Gunter Winkler (TU Graz) Dr. Bernd Deutschmann (Infineon Technologies AG) Page 1 Agenda Filter design basics Filter Attenuation

More information