DS V EconoReset PIN ASSIGNMENT FEATURES PIN DESCRIPTION PIN 1 GROUND PIN 2 RESET PIN 3 V CC PIN 4 GROUND (SOT 223 ONLY)
|
|
|
- Hugo Howard
- 5 years ago
- Views:
Transcription
1 5V EconoReset FEATURES Automatically restarts microprocessor after power failure Monitors pushbutton for external override Internal circuitry debounces pushbutton switch PIN ASSIGNMENT DALLAS Econo Reset Maintains reset for 350 ms after returns to an in tolerance condition or pushbutton released Accurate 5%, 10% or 15% microprocessor 5V power supply monitoring Reduces need for discrete components Precision temperature compensated voltage reference and voltage sensor Low cost TO 92 package or surface mount SOT 223 package Internal 5KΩ pull up resistor Operating temperature of 40 C to +85 C TO 92 PACKAGE See Mech. Drawings Section SOT 223 PACKAGE See Mech. Drawings Section PIN DESCRIPTION PIN 1 GROUND PIN 2 RESET PIN 3 PIN 4 GROUND (SOT 223 ONLY) DESCRIPTION The EconoReset monitors two vital conditions for a microprocessor: power supply and external override. A precision temperature compensated reference and comparator circuit are used to monitor the status of the power supply ( ). When an out of tolerance condition is detected, an internal power fail signal is generated which forces reset to the active state. When returns to an in tolerance condition, the reset signal is kept in the active state for approximately 350 ms to allow the power supply and processor to stabilize. The second function of the is pushbutton reset control. The debounces a pushbutton closure and will generate a 350 ms reset pulse upon release. Copyright 1995 by Dallas Semiconductor Corporation. All Rights Reserved. For important information regarding patents and other intellectual property rights, please refer to Dallas Semiconductor data books /5
2 OPERATION POWER MONITOR The provides the functions of detecting out of tolerance power supply conditions and warning a processor based system of impending power failure. When is detected as out of tolerance, as defined by the tolerance of the part selected, the signal is asserted. On power up, is kept active for approximately 350 ms after the power supply has reached the selected tolerance. This allows the power supply and microprocessor to stabilize before is released. OPERATION PUSHBUTTON RESET The provides for a pushbutton switch to be connected to the output pin. When the is not in a reset cycle, it continuously monitors the signal for a low going edge. If an edge is detected, the will debounce the switch by pulling the line low. After the internal timer has expired, the will continue to monitor the line. If the line is still low, the will continue to monitor the line looking for a rising edge. Upon detecting a release, the will force the line low and hold it low for 350 ms. NOTE: For proper operation with an external pushbutton, a capacitor between 100 pf and 0.01 µf must be connected between and ground. In applications where additional reset current is required, a minimum capacitance of 500 pf should be used, along with a parallel external pull up resistor of 1KΩ minimum. BLOCK DIAGRAM Figure 1 Vcc MONITOR Vcc TOLERANCE AND BIAS 350 ms DELAY Ground T.C. REFERENCE APPLICATION EXAMPLE Figure 2 MICROPROCESSOR RESET PUSHBUTTON CAPACITOR /5
3 PUSHBUTTON RESET Figure 3 V OH PB DV PB RD PB DB t POWER UP Figure 4 t R 4.75V 4.00V TP t RPU V OH POWER DOWN Figure 5 t F 4.75V TP 4.00V t RPD V OL /5
4 ABSOLUTE MAXIMUM RATINGS* Voltage on Pin Relative to Ground Voltage on I/O Relative to Ground Operating Temperature Storage Temperature Soldering Temperature 0.5V to +7.0V 0.5V to +0.5V 40 C to +85 C 55 C to +125 C 260 C for 10 seconds * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED DC OPERATING CONDITIONS ( 40 C to +85 C) Supply Voltage V 1 DC ELECTRICAL CHARACTERISTICS ( 40 C to +85 C; V DD = 5V + 10%) Low V OL 0.4 V 1 Output 0.4V I OL +8 ma Operating Current I CC 50 µa Trip Point 5% TP V 1 Trip Point 10% TP V 1 Trip Point 15% TP V 1 Output Capacitance C OUT 10 pf Pushbutton Detect PB DV V 1 Pushbutton Release PB RD V 1, 2 Internal Pull Up Resistor R P KΩ AC ELECTRICAL CHARACTERISTICS ( 40 C to +85 C; = 5V + 10%) Reset Active Time t ms Detect to t RPD 100 ns Slew Rate (4.75V 4.00V) t F 300 µs Slew Rate (4.00V 4.75V) t R 0 ns Pushbutton Debounce PB DB ms detect to t RPU ms NOTES: 1. All voltages are referenced to ground. 2. With a 100 pf to 0.01 µf capacitor connected from to ground /5
5 ECONORESET SELECTION GUIDE VCC TRIP POINT PUSHBUTTON DETECT MIN TYP MAX MIN TYP MAX D N/A N/A 5V D N/A N/A D N/A N/A DS N/A N/A DS N/A N/A DS N/A N/A 33V 3.3V A A /5
DS1707/DS and 5.0-Volt MicroMonitor
www.maxim-ic.com FEATURES Holds microprocessor in check during power transients Automatically restarts microprocessor after power failure Monitors pushbutton for external override Accurate 5%, 10% or 20%
DS1232LP/LPS Low Power MicroMonitor Chip
DS1232LP/LPS Low Power MicroMonitor Chip www.dalsemi.com FEATURES Super-low power version of DS1232 50 µa quiescent current Halts and restarts an out-of-control microprocessor Automatically restarts microprocessor
DS1231/S Power Monitor Chip
Power Monitor Chip FEATURES Warns processor of an impending power failure Provides time for an orderly shutdown Prevents processor from destroying nonvolatile memory during power transients Automatically
ASM1232LP/LPS 5V μp Power Supply Monitor and Reset Circuit
5V μp Power Supply Monitor and Reset Circuit General Description The ASM1232LP/LPS is a fully integrated microprocessor Supervisor. It can halt and restart a hung-up microprocessor, restart a microprocessor
PT7M1818/1813 Supervisory Circuit
Features Highly accurate: 1.5% (25 C) Accurate power monitoring: 2.5V, 2.9V, 3. (PT7M1818), and 4.1, 4.3, 4.6V (PT7M1813) Operating voltage range: 1. ~ 5.5V Operating temperature range: -40 C to + 85 C
olerance and eriodiod Push-Button ResetR -Point TolerT POWER MANAGEMENT Key Features Block Diagram IMP1832
POWER MANAGEMENT.V µp P Power P Supply Monitor or and Reset R Circuit Selectable Trip-PT -Point TolerT olerance and Watchdog hdog PerP eriodiod Push-Button ResetR Push-Pull Reset R Outputs The IMP82 microprocessor
PT7M6314US. Supervisory Circuit General Description. Features. Pin Configuration. Description
Features Highly accurate: 1.5% (25 C) Detect voltage range: 1.8 to 5V in 100mV increments Operating voltage range: 1. ~ 5.5V Operating temperature range: -40 C to + 85 C Detect voltage temperature characteristics:
SGM706 Low-Cost, Microprocessor Supervisory Circuit
GENERAL DESCRIPTION The microprocessor supervisory circuit reduces the complexity and number of components required to monitor power supply and monitor microprocessor activity. It significantly improves
PT7M6315US. Pin Configuration PT7M6315USxxD3F/D4F. Pin Description
Features Highly accurate: 1.5% (25 C) Detect voltage range: 1.8 to 5 in 100m increments Operating voltage range: 1.0 ~ 5.5 Operating temperature range: -40 C to + 85 C Detect voltage temperature characteristics:
SGM706 Low-Cost, Microprocessor Supervisory Circuit
GENERAL DESCRIPTION The microprocessor supervisory circuit reduces the complexity and number of components required to monitor power-supply and monitor microprocessor activity. It significantly improves
DS in 1 High Speed Silicon Delay Line FEATURES PIN ASSIGNMENT
DS1044 4 in 1 High Speed Silicon Delay Line FEATURES All silicon timing circuit Four independent buffered delays Initial delay tolerance ±1.5 ns Stable and precise over temperature and voltage Leading
SGM706 Low-Cost, Microprocessor Supervisory Circuit
GENERAL DESCRIPTION The microprocessor supervisory circuit reduces the complexity and number of components required to monitor power-supply and monitor microprocessor activity. It significantly improves
RT9807. Micro-Power Voltage Detector with Manual Reset. General Description. Features. Applications. Pin Configurations. Ordering Information RT9807-
Micro-Power Voltage Detector with Manual Reset General Description The is a micro-power voltage detector with deglitched manual reset input which supervises the power supply voltage level for microprocessors
DS1202, DS1202S. Serial Timekeeping Chip FEATURES PIN ASSIGNMENT. ORDERING INFORMATION DS pin DIP DS1202S 16 pin SOIC DS1202S8 8 pin SOIC
DS22, DS22S Serial Timekeeping Chip FEATURES Real time clock counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap year compensation 2 x 8 RAM for scratchpad data
DS in-1 Low Voltage Silicon Delay Line
3-in-1 Low Voltage Silicon Delay Line www.dalsemi.com FEATURES All-silicon timing circuit Three independent buffered delays Initial delay tolerance ±1.5 ns Stable and precise over temperature and voltage
DS1801 Dual Audio Taper Potentiometer
DS1801 Dual Audio Taper Potentiometer www.dalsemi.com FEATURES Ultra-low power consumption Operates from 3V or 5V supplies Two digitally controlled, 65-position potentiometers including mute Logarithmic
Microprocessor Supervisory Circuit ADM1232
Microprocessor Supervisory Circuit FEATURES Pin-compatible with MAX1232 and Dallas DS1232 Adjustable precision voltage monitor with 4.5 V and 4.75 V options Adjustable strobe monitor with 150 ms, 600 ms,
DS1307ZN. 64 X 8 Serial Real Time Clock PIN ASSIGNMENT FEATURES
DS1307 64 8 Serial Real Time Clock FEATURES Real time clock counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap year compensation valid up to 2100 56 byte nonvolatile
ASM1816. Low Power, 3.3 V/3.0 V, P Reset, Active LOW, Open-Drain Output
Low Power, 3.3 V/3.0 V, P Reset, Active LOW, Open-Drain Output Description The ASM1816 is a voltage supervisory device with low power, 3.3 V/3 V P Reset, active LOW, open drain output. Maximum supply current
DS Tap High Speed Silicon Delay Line
www.dalsemi.com FEATURES All-silicon timing circuit Five delayed clock phases per input Precise tap-to-tap nominal delay tolerances of ±0.75 and ±1 ns Input-to-tap 1 delay of 5 ns Nominal Delay tolerances
DS1802 Dual Audio Taper Potentiometer With Pushbutton Control
www.dalsemi.com FEATURES Ultra-low power consumption Operates from 3V or 5V supplies Two digitally controlled, 65-position potentiometers including mute Logarithmic resistive characteristics (1 db per
DS1633. High Speed Battery Recharger PIN ASSIGNMENT TO 220 FEATURES. PIN DESCRIPTION V CC Supply Voltage V BAT Battery Output GND Ground
DS1633 High Speed Battery Recharger FEATURES Recharges Lithium, NiCad, NiMH and Lead acid batteries Retains battery and power supply limits in onboard memory PIN ASSIGNMENT TO 220 + Serial 1 wire interface
Low-Cost Microprocessor Supervisory Circuits with Battery Backup
General Description The / microprocessor (μp) supervisory circuits reduce the complexity and number of components required for power-supply monitoring and battery control functions in μp systems. These
Setup Period. General Description
General Description The MAX6443 MAX6452 low-current microprocessor reset circuits feature single or dual manual reset inputs with an extended setup period. Because of the extended setup period, short switch
PART TEMP RANGE PIN-PACKAGE SPEED
Rev 0; 8/06 General Description The is a 16Mb reflowable nonvolatile (NV) SRAM, which consists of a static RAM (SRAM), an NV controller, and an internal rechargeable manganese lithium (ML) battery. These
+5V, Low-Power µp Supervisory Circuits with Adjustable Reset/Watchdog
19-1078; Rev 4; 9/10 +5V, Low-Power µp Supervisory Circuits General Description The * low-power microprocessor (µp) supervisory circuits provide maximum adjustability for reset and watchdog functions.
Low Power Windowed Watchdog with Reset, Sleep Mode Functions. Features. Applications. Selection Table. Part Number V REF
EM MICROELECTRONIC - MARIN SA Low Power Windowed Watchdog with Reset, Sleep Mode Functions Description The offers a high level of integration by combining voltage monitoring and software monitoring using
Supervisory Circuits with Watchdog and Manual Reset in 5-Lead SC70 and SOT-23 ADM823/ADM824/ADM825
Data Sheet Supervisory Circuits with Watchdog and Manual Reset in 5-Lead SC70 and SOT-23 ADM823/ADM824/ADM825 FEATURES FUNCTIONAL BLOCK DIAGRAM Precision 2.5 V to 5 V power supply monitor 7 reset threshold
Low-Power, Single/Dual-Voltage μp Reset Circuits with Capacitor-Adjustable Reset Timeout Delay
General Description The MAX6412 MAX6420 low-power microprocessor supervisor circuits monitor system voltages from 1.6V to 5V. These devices are designed to assert a reset signal whenever the supply voltage
DS1088L 1.0. PART FREQUENCY (MHz) TEMP RANGE PIN-PACKAGE DS1088LU C to +85 C 8 µsop. DS1088LU C to +85 C 8 µsop
Rev 0; /0 % PART FREQUENCY (MHz) TEMP RANGE PIN-PACKAGE U-02 2.0 C to + C µsop U-.0 C to + C µsop U-1 1. C to + C µsop U-. C to + C µsop U-0 0.0 C to + C µsop U-yyy * C to + C µsop * 12kHz TO PUT TOP VIEW
ADM6823. Low Voltage, Supervisory Circuit with Watchdog and Manual Reset in 5-Lead SOT-23. Data Sheet FUNCTIONAL BLOCK DIAGRAM FEATURES APPLICATIONS
Data Sheet Low Voltage, Supervisory Circuit with Watchdog and Manual Reset in 5-Lead SOT-23 FEATURES Precision low voltage monitoring 9 reset threshold options: 1.58 V to 4.63 V (typical) 140 ms (minimum)
Dallastat TM Electronic Digital Rheostat
DS1668, DS1669, DS1669S Dallastat TM Electronic Digital Rheostat FEATURES Replaces mechanical variable resistors Available as the DS1668 with manual interface or the DS1669 integrated circuit Human engineered
DS1869 3V Dallastat TM Electronic Digital Rheostat
www.dalsemi.com FEATURES Replaces mechanical variable resistors Operates from 3V or 5V supplies Electronic interface provided for digital as well as manual control Internal pull-ups with debounce for easy
DS1090 OUTPUT FREQUENCY RANGE PIN- PACKAGE PART PRESCALER
Rev ; / PART OUTPUT FREQUENCY RANGE PRESCALER * PIN- PACKAGE U-1 MHz to MHz 1 µsop U-2* 2MHz to MHz 2 µsop U-* 1MHz to 2MHz µsop U-* 5kHz to 1MHz µsop U-16 U-32* 25kHz to 5kHz 125kHz to 25kHz 16 µsop 32
3V 10-Tap Silicon Delay Line DS1110L
XX-XXXX; Rev 1; 11/3 3V 1-Tap Silicon Delay Line General Description The 1-tap delay line is a 3V version of the DS111. It has 1 equally spaced taps providing delays from 1ns to ns. The series delay lines
DS in-1 Silicon Delay Line
www.dalsemi.com FEATURES All-silicon time delay 3 independent buffered delays Delay tolerance ±2ns for -10 through 60 Stable and precise over temperature and voltage range Leading and trailing edge accuracy
Extremely Accurate Power Surveillance, Software Monitoring and Sleep Mode Detection. Pin Assignment. Fig. 1
EM MICOELECTONIC - MAIN SA Extremely Accurate Power Surveillance, Software Monitoring and Sleep Mode Detection Description The offers a high level of integration by voltage monitoring and software monitoring
G692/G693 4-Pin µp Voltage Monitors with Manual Reset Input
4-Pin µp Voltage Monitors with Manual Reset Input Features Precision Monitoring of +3V, +3.3V, and +5V Power-Supply Voltages Fully Specified Over Temperature Available in Three Output Configurations Push-Pull
DS1267B Dual Digital Potentiometer
Dual Digital Potentiometer FEATURES Two digitally controlled, 256-position potentiometers Serial port provides means for setting and reading both potentiometers Resistors can be connected in series to
Low-Voltage, 1.8kHz PWM Output Temperature Sensors
19-266; Rev 1; 1/3 Low-Voltage, 1.8kHz PWM Output Temperature General Description The are high-accuracy, low-power temperature sensors with a single-wire output. The convert the ambient temperature into
CD4541BC Programmable Timer
CD4541BC Programmable Timer General Description The CD4541BC Programmable Timer is designed with a 16-stage binary counter, an integrated oscillator for use with an external capacitor and two resistors,
PIN ASSIGNMENT TAP 2 TAP 4 GND DS PIN DIP (300 MIL) See Mech. Drawings Section IN TAP 2 TAP 4 GND
DS1000 5-Tap Silicon Delay Line FEATURES All-silicon time delay 5 taps equally spaced Delays are stable and precise Both leading and trailing edge accuracy Delay tolerance +5% or +2 ns, whichever is greater
DS1669 Dallastat TM Electronic Digital Rheostat
Dallastat TM Electronic Digital Rheostat www.dalsemi.com FEATURES Replaces mechanical variable resistors Electronic interface provided for digital as well as manual control Wide differential input voltage
POWER MANAGEMENT. Key Features. Applications. Block Diagrams. Reset Threshold Suffix Voltage (V)
POWER MANAGEMENT 4-Pin µp P VoltV oltage e Supervisor with h Manual ResetR The /IMP812 are low-power supervisors designed to monitor voltage levels of 3.0V, 3.3V and 5.0V power supplies in low-power microprocessor
Reset in SOT23-3. General Description. Ordering Information. Applications. Typical Operating Circuit. Pin Configuration
General Description The MAX633/ combine a precision shunt regulator with a power-on reset function in a single SOT23-3 package. They offer a low-cost method of operating small microprocessor (µp)-based
High-Accuracy μp Reset Circuit
General Description The MAX6394 low-power CMOS microprocessor (μp) supervisory circuit is designed to monitor power supplies in μp and digital systems. It offers excellent circuit reliability by providing
Low-Voltage, High-Accuracy, Triple/Quad Voltage µp Supervisory Circuits in SOT Package
19-2324; Rev 2; 12/05 Low-oltage, High-Accuracy, Triple/Quad General Description The precision triple/quad voltage microprocessor (µp) supervisory circuits monitor up to four system-supply voltages and
DS1803 Addressable Dual Digital Potentiometer
www.dalsemi.com FEATURES 3V or 5V Power Supplies Ultra-low power consumption Two digitally controlled, 256-position potentiometers 14-Pin TSSOP (173 mil) and 16-Pin SOIC (150 mil) packaging available for
DS14C238 Single Supply TIA/EIA x 4 Driver/Receiver
Single Supply TIA/EIA-232 4x4Driver/Receiver General Description The DS14C238 is a four driver, four receiver device which conforms to the TIA/EIA-232-E standard and CCITT V.28 recommendations. This device
CONSONANCE Ultra Low Power Microprocessor Reset IC CN803/809/CN810 General Description Features Pin Assignment Applications
CONSONANCE Ultra Low Power Microprocessor Reset IC CN803/809/CN810 General Description The CN803/809/810 series are micro- processor (µp) supervisory circuits used to monitor the power supplies in µp and
DS1270W 3.3V 16Mb Nonvolatile SRAM
19-5614; Rev 11/10 www.maxim-ic.com 3.3V 16Mb Nonvolatile SRAM FEATURES Five years minimum data retention in the absence of external power Data is automatically protected during power loss Unlimited write
Low-Cost Microprocessor Supervisory Circuits with Battery Backup
19-0130; Rev 2; 11/05 Low-Cost Microprocessor Supervisory General Description The microprocessor (µp) supervisory circuits reduce the complexity and number of components required for power-supply monitoring
DS1720. Econo Digital Thermometer and Thermostat PRELIMINARY FEATURES PIN ASSIGNMENT
PRELIMINARY DS1720 Econo Digital Thermometer and Thermostat FEATURES Requires no external components Supply voltage range covers from 2.7V to 5.5V Measures temperatures from 55 C to +125 C in 0.5 C increments.
DS1806 Digital Sextet Potentiometer
Digital Sextet Potentiometer www.dalsemi.com FEATURES Six digitally controlled 64-position potentiometers 3-wire serial port provides for reading and setting each potentiometer Devices can be cascaded
MIC803. Features. General Description. Applications. Typical Application. 3-Pin Microprocessor Supervisor Circuit with Open-Drain Reset Output
3-Pin Microprocessor Supervisor Circuit with Open-Drain Reset Output General Description The is a single-voltage supervisor with open-drain reset output that provides accurate power supply monitoring and
DS Tap Silicon Delay Line
www.dalsemi.com FEATURES All-silicon time delay 10 taps equally spaced Delays are stable and precise Leading and trailing edge accuracy Delay tolerance ±5% or ±2 ns, whichever is greater Economical Auto-insertable,
Dual Processor Supervisors with Watchdog ADM13305
Dual Processor Supervisors with Watchdog ADM335 FEATURES Dual supervisory circuits Supply voltage range of 2.7 V to 5.5 V Pretrimmed threshold options:.8 V, 2.5 V, 3.3 V, and 5 V Adjustable.6 V voltage
Features. Ordering Information VCC MIC8114 RESET
MIC8114 Microprocessor Reset Circuit General Description The MIC8114 is an inexpensive microprocessor supervisory circuit that monitors the power supply in microprocessor based systems. The function of
STM706T/S/R, STM706P, STM708T/S/R
STM706T/S/R, STM706P, STM708T/S/R 3V Supervisor FEATURES SUMMARY PRECISION MONITOR STM706/708 T: 3.00V V 3.15V S: 2.88V V 3.00V R; STM706P: 2.59V V 2.70V AND OUTPUTS 200ms (TYP) t rec WATCHDOG TIMER -
DS1267 Dual Digital Potentiometer Chip
Dual Digital Potentiometer Chip www.dalsemi.com FEATURES Ultra-low power consumption, quiet, pumpless design Two digitally controlled, 256-position potentiometers Serial port provides means for setting
4-Pin Microprocessor Power Supply Supervisors with Manual Reset
4-Pin Microprocessor Power Supply Supervisors with Manual Reset, CAT812 FEATURES Precision monitoring of +5.0 V (± 5%, ± 10%, ± 20%), +3.3 V (± 5%, ± 10%), +3.0 V (± 10%) and +2.5 V (± 5%) power supplies
TL494M PULSE-WIDTH-MODULATION CONTROL CIRCUIT
Complete PWM Power Control Circuitry Uncommitted Outputs for 00-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
DS Tap Silicon Delay Line
www.dalsemi.com FEATURES All-silicon time delay 5 taps equally spaced Delay tolerance ±2 ns or ±3%, whichever is greater Stable and precise over temperature and voltage range Leading and trailing edge
DM96S02 Dual Retriggerable Resettable Monostable Multivibrator
January 1992 Revised June 1999 DM96S02 Dual Retriggerable Resettable Monostable Multivibrator General Description The DM96S02 is a dual retriggerable and resettable monostable multivibrator. This one-shot
PART* MAX812_EUS-T TOP VIEW
19-11; Rev ; /98 -Pin µp oltage Monitors General Description The are low-power microprocessor (µp) supervisory circuits used to monitor power supplies in µp and digital systems. They provide excellent
DS275S. Line-Powered RS-232 Transceiver Chip PIN ASSIGNMENT FEATURES ORDERING INFORMATION
Line-Powered RS-232 Transceiver Chip FEATURES Low power serial transmitter/receiver for battery-backed systems Transmitter steals power from receive signal line to save power Ultra low static current,
Continuous Wave Laser Average Power Controller ADN2830
a FEATURES Bias Current Range 4 ma to 200 ma Monitor Photodiode Current 50 A to 1200 A Closed-Loop Control of Average Power Laser and Laser Alarms Automatic Laser Shutdown, Full Current Parameter Monitoring
TOP VIEW. Maxim Integrated Products 1
19-3474; Rev 2; 8/07 Silicon Oscillator with Low-Power General Description The dual-speed silicon oscillator with reset is a replacement for ceramic resonators, crystals, crystal oscillator modules, and
Synchronous Buck Converter Controller
Product is End of Life 3/204 Synchronous Buck Converter Controller Si950 DESCRIPTION The Si950 synchronous buck regulator controller is ideally suited for high-efficiency step down converters in battery-powered
Maxim Integrated Products 1
19-1951; Rev 3; 1/5 SOT3 Power-Supply Sequencers General Description The are power-supply sequencers for dual-voltage microprocessors (µps) and multivoltage systems. These devices monitor a primary supply
1.0V Micropower, SOT23, Operational Amplifier
19-3; Rev ; 1/ 1.V Micropower, SOT3, Operational Amplifier General Description The micropower, operational amplifier is optimized for ultra-low supply voltage operation. The amplifier consumes only 9µA
Low Cost P Supervisory Circuits ADM705 ADM708
a FEATURES Guaranteed Valid with = 1 V 190 A Quiescent Current Precision Supply-Voltage Monitor 4.65 V (ADM707) 4.40 V (/) 200 ms Reset Pulsewidth Debounced TTL/CMOS Manual Reset Input () Independent Watchdog
DS1307ZN. 64 X 8 Serial Real Time Clock
64 X 8 Serial Real Time Clock www.dalsemi.com FEATURES Real time clock counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap year compensation valid up to 2100 56
DS1135L 3V 3-in-1 High-Speed Silicon Delay Line
3V 3-in-1 High-Speed Silicon Delay Line FEATURES All-Silicon Timing Circuit Three Independent Buffered Delays Stable and Precise Over Temperature and Voltage Leading and Trailing Edge Precision Preserves
SGM4064 Over-Voltage Protection IC and Li+ Charger Front-End Protection IC with LDO Mode
GENERAL DESCRIPTION The SGM4064 is a charger front-end integrated circuit designed to provide protection to Li-ion batteries from failures of the charging circuitry. The IC continuously monitors the input
Ultra-Low-Voltage µp Reset Circuits and Voltage Detectors
19-2625; Rev 2; 12/05 Ultra-Low-oltage µp Reset Circuits and General Description The microprocessor (µp) supervisory circuits monitor ultra-low-voltage power supplies in µp and digital systems. They provide
TL494C, TL494I, TL494M, TL494Y PULSE-WIDTH-MODULATION CONTROL CIRCUITS
Complete PWM Power Control Circuitry Uncommitted Outputs for 00-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
TL594C, TL594I, TL594Y PULSE-WIDTH-MODULATION CONTROL CIRCUITS
Complete PWM Power Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
DS2114. SCSI Terminator FEATURES PIN ASSIGNMENT
DS2114 Terminator FEATURES Fully compliant with, 2 and 3 standards Provides active termination for nine signal lines Laser trimmed termination resistors have 2% tolerance Low dropout voltage regulator
Low-Power, Single/Dual-Voltage µp Reset Circuits with Capacitor-Adjustable Reset Timeout Delay. Maxim Integrated Products 1
19-2336; Rev 2; 12/05 Low-Power, Single/Dual-Voltage µp Reset Circuits General Description The low-power microprocessor supervisor circuits monitor system voltages from 1.6V to 5V. These devices are designed
DATA SHEET. HEF4538B MSI Dual precision monostable multivibrator. For a complete data sheet, please also download: INTEGRATED CIRCUITS
INTEGRATED CIRCUITS DATA SHEET For a complete data sheet, please also download: The IC04 LOCMOS HE4000B Logic Family Specifications HEF, HEC The IC04 LOCMOS HE4000B Logic Package Outlines/Information HEF,
LP3470 Tiny Power On Reset Circuit
Tiny Power On Reset Circuit General Description The LP3470 is a micropower CMOS voltage supervisory circuit designed to monitor power supplies in microprocessor (µp) and other digital systems. It provides
DS1307/DS X 8 Serial Real Time Clock
DS1307/DS1308 64 X 8 Serial Real Time Clock www.dalsemi.com FEATURES Real time clock counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap year compensation valid
DS1867 Dual Digital Potentiometer with EEPROM
Dual Digital Potentiometer with EEPROM www.dalsemi.com FEATURES Nonvolatile version of the popular DS1267 Low power consumption, quiet, pumpless design Operates from single 5V or ±5V supplies Two digitally
MAX9812/MAX9813 Tiny, Low-Cost, Single/Dual-Input, Fixed-Gain Microphone Amplifiers with Integrated Bias
General Description The MAX982/MAX983 are single/dual-input, 20dB fixed-gain microphone amplifiers. They offer tiny packaging and a low-noise, integrated microphone bias, making them ideal for portable
ICS PLL BUILDING BLOCK
Description The ICS673-01 is a low cost, high performance Phase Locked Loop (PLL) designed for clock synthesis and synchronization. Included on the chip are the phase detector, charge pump, Voltage Controlled
TL594 PULSE-WIDTH-MODULATION CONTROL CIRCUITS
Complete PWM Power Control Circuitry Uncommitted Outputs for 200-mA Sink or Source Current Output Control Selects Single-Ended or Push-Pull Operation Internal Circuitry Prohibits Double Pulse at Either
Dual-/Triple-/Quad-Voltage, Capacitor- Adjustable, Sequencing/Supervisory Circuits
19-0622; Rev 0; 8/06 Dual-/Triple-/Quad-Voltage, Capacitor- General Description The are dual-/triple-/ quad-voltage monitors and sequencers that are offered in a small thin QFN package. These devices offer
Low-Voltage, High-Accuracy, Triple/Quad Voltage μp Supervisory Circuits in SOT Package
General Description The MAX6700/MAX6710 precision triple/quad voltage microprocessor (μp) supervisory circuits monitor up to four system-supply voltages and assert a single reset if any supply voltage
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. TPS3808 Low Quiescent Current, Programmable-Delay Supervisory Circuit SBVS050E
DS1065 EconOscillator/Divider
wwwdalsemicom FEATURES 30 khz to 100 MHz output frequencies User-programmable on-chip dividers (from 1-513) User-programmable on-chip prescaler (1, 2, 4) No external components 05% initial tolerance 3%
TL1451AC, TL1451AY DUAL PULSE-WIDTH-MODULATION CONTROL CIRCUITS
SLVS4C FEBRUARY 983 REVISED OCTOBER 995 Complete PWM Power Control Circuitry Completely Synchronized Operation Internal Undervoltage Lockout Protection Wide Supply Voltage Range Internal Short-Circuit
DS1040 Programmable One-Shot Pulse Generator
www.dalsemi.com FEATURES All-silicon pulse width generator Five programmable widths Equal and unequal increments available Pulse widths from 5 ns to 500 ns Widths are stable and precise Rising edge-triggered
Single/Dual/Triple-Voltage μp Supervisory Circuits with Independent Watchdog Output
General Description The MAX6730 MAX6735 single/dual/triple-voltage microprocessor (μp) supervisors feature a watchdog timer and manual reset capability. The MAX6730 MAX6735 offer factory-set reset thresholds
DS1868B Dual Digital Potentiometer
www. maximintegrated.com FEATURES Two digitally controlled, 256-position potentiometers Serial port provides means for setting and reading both potentiometers Resistors can be connected in series to provide
Advanced Monolithic Systems
Advanced Monolithic Systems FEATURES Internal Power Switch Output Voltage up to 20V Up to 89% Efficiency Low 0.08µA Shutdown Supply Current Internal Current Limit Thermal Shutdown Available in 5-Pin SOT-23
description TPS3836, TPS3838 DBV PACKAGE (TOP VIEW) V DD GND RESET TPS3837 DBV PACKAGE (TOP VIEW)
М TPS3836E18-Q1 / J25-Q1 / H30-Q1 / L30-Q1 / K33-Q1 Qualified for Automotive Applications Customer-Specific Configuration Control Can Be Supported Along With Major-Change Approval ESD Protection Exceeds
DS1866 Log Trimmer Potentiometer
og Trimmer Potentiometer www.dalsemi.com FEATURES Single 8-position og Trimmer Potentiometer -db/step Operates from 2.7V to.v supplies Parallel interface control: P0, P1, P2 Standard Resistance Value:
nanopower, Tiny Supervisor with Manual Reset Input
General Description The MAX16140 is an ultra-low-current, single-channel supervisory IC in a tiny, 4-bump, wafer-level package (WLP). The MAX16140 monitors the V CC voltage from 1.7V to 4.85V in 50mV increments
3 Pin Microcontroller Power Supply Supervisor L 4.63 M 4.38 J 4.00 T 3.08 S 2.93 R Features: V CC
General Description Six voltage thresholds are available to support 3V to 5V systems: The /ASM810 are cost effective 3.0V, 3.3V and 5.0V power supply supervisor circuits optimized for low-power microprocessor