ISO13316: DC to 6 GHz Hermetic GaAs IC SPST Non-Reflective Switch

Transcription

1 DT SHEET ISO336: DC to 6 GHz Hermetic Gas IC SPST Non-Reflective Switch Features Wideband frequency range: DC to 6 GHz Isolation: 2 GHz Low 6 GHz RF reflective / non-reflective High reliability Class B and S screening available RF Description The ISO336 is a Gas phemt non-reflective, high-performance, low-loss switch. The ISO336 uses hermetic surface-mount technology (SMT) for defense and satellite applications. The device can be supplied and tested to the screening requirements of MIL-PRF Class B and S, in addition to the required QCI. B Figure. ISO336 Block Diagram functional block diagram of the ISO336 is shown in Figure. The ISO336 device package and pinout are shown in Figure 2. Pin assignments and signal descriptions are shown in Table. Y95 Table. ISO336 Pin Descriptions Pin Name Description RF port 2 2 Ground 3 RF RF port 2 4 Ground 5 Control voltage RF 3 6 B Control voltage B 7 Ground Y94 B Figure 2. ISO336 Pinout (Top View) 23249B Isolink Proprietary Information Products and Product Information are Subject to Change Without Notice pril 8, 27

2 DT SHEET ISO336: DC TO 6 GHz HERMETIC Gas IC SPST NON-REFLECTIVE SWITCH Electrical and Mechanical Specifications The absolute maximum ratings of the ISO336 are provided in Table 2. Electrical specifications are provided in Table 3. The truth table is shown in Table 4. Typical performance characteristics of the ISO336 are illustrated in Figures 3 through 8. Table 2. ISO336 bsolute Maximum Ratings (Note ) Parameter Minimum Maximum Units Control voltages ( and B) V RF input power +3 m Storage temperature C Operating case temperature C Junction temperature +5 C Operating frequency.3 6. GHz Note : Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CUTION: lthough this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. ISO336 Electrical Specifications (Note ) ( of 2) (VCTL = V/ 5 V, T = +25 C, PINPUT = m, Z = 5 Ω, Unless Otherwise Noted) Parameter Test Condition Frequency Min Typical Max Units Insertion loss DC to 2. GHz 2. to 3. GHz 3. to 4. GHz 4. to 6. GHz RF/ return loss (ON state) DC to 2. GHz 2. to 3. GHz 3. to 4. GHz 4. to 6. GHz 24 8 return loss (OFF state) DC to 2. GHz 2. to 3. GHz 3. to 4. GHz 4. to 6. GHz 24 8 Isolation DC to 2. GHz 2. to 3. GHz 3. to 4. GHz 4. to 6. GHz pril 8, 27 Isolink Proprietary Information Products and Product Information are Subject to Change Without Notice 23249B

3 DT SHEET ISO336: DC TO 6 GHz HERMETIC Gas IC SPST NON-REFLECTIVE SWITCH Table 3. ISO336 Electrical Specifications (Note ) (2 of 2) (VCTL = V/ 5 V, T = +25 C, PINPUT = m, Z = 5 Ω, Unless Otherwise Noted) Parameter Test Condition Frequency Min Typical Max Units Switching characteristics % RF envelope to 9% RF envelope 9% RF envelope to % RF envelope 5% VCTL to 9% RF envelope 5% VCTL to % RF envelope Video feed-through ns ns mv Input power for compression CW.5 GHz to 4.5 GHz +25 m Input power for. compression CW.5 GHz to 4.5 GHz +24 m Intermodulation intercept point (IP3) Two tone input power = +3 m per tone, MHz spacing.5 GHz to 3.5 GHz +46 m Control voltages Control currents VCTL Low VCTL High VCTL Low VCTL High Note : Performance is guaranteed only under the conditions listed in this table V V 2 μ μ Table 4. Truth Table Control Input Signal Path State B RF to High Low ON Low High OFF 23249B Isolink Proprietary Information Products and Product Information are Subject to Change Without Notice pril 8, 27 3

4 DT SHEET ISO336: DC TO 6 GHz HERMETIC Gas IC SPST NON-REFLECTIVE SWITCH Typical Performance Characteristics (PIN = m, Z = 5 Ω, Unless Otherwise Noted) Insertion Loss (S2) () C Figure 3. Typical Insertion Loss (S2) Y233 Return Loss (S) () Figure 4. Typical J Return Loss (Insertion Loss State S) +25 C Y234 Isolation (S2) () C Figure 5. Typical Isolation (S2) Y235 Return Loss (S22) () C Note: The data lines for +25 C and +25 C are essentially identical Figure 6. Typical J2 Return Loss (Isolation State S22) Y P/P. (m) P +25 C P +25 C P 55 C P. +25 C P. +25 C P Figure 7. P (.) v Frequency v Temperature Y866 IP3 () IP3 +25 C IP3 +25 C IP3 55 C Frequency (MHz) Figure 8. IP3 v Frequency (.5 to 3.5 GHz) v Temperature Y867 4 pril 8, 27 Isolink Proprietary Information Products and Product Information are Subject to Change Without Notice 23249B

5 DT SHEET ISO336: DC TO 6 GHz HERMETIC Gas IC SPST NON-REFLECTIVE SWITCH Evaluation Board Description The ISO336 Evaluation Board is used to test the performance of the ISO336 switch. schematic of the Evaluation Board is shown in Figure 7. n assembly drawing for the Evaluation Board is shown in Figure 8. Package Dimensions Package dimensions for the ISO336 are shown in Figure 9. J J2 SM C pf C2 pf SM J SM C pf 3 5 U ISO336 RF B 6 C2 pf J2 SM J CON4 Y863 Figure 7. ISO336 Evaluation Board ISO336EVB J RF U C J C THRU J3 Isolink 25 J2 C2 J2 C2 Y88 Figure 8. Evaluation Board ssembly Diagram 23249B Isolink Proprietary Information Products and Product Information are Subject to Change Without Notice pril 8, 27 5

6 DT SHEET ISO336: DC TO 6 GHz HERMETIC Gas IC SPST NON-REFLECTIVE SWITCH ± Max.5 ± ±. Y96 Figure 9. ISO336 Package Dimensions Skyworks Solutions, Inc. Phone [78] Fax [78] sales@skyworksinc.com 6 pril 8, 27 Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice 23249B

7 DT SHEET ISO336: DC TO 6 GHz HERMETIC Gas IC SPST NON-REFLECTIVE SWITCH Ordering Information ISO336: DC to 6 GHz Low Loss SPST Model Name ISO336 Manufacturing Part Number Copyright 25, 27 Isolink, Inc. ll Rights Reserved. Information in this document is provided in connection with Isolink, Inc. ( Isolink ), a wholly-owned subsidiary of Skyworks Solutions, Inc. These materials, including the information contained herein, are provided by Isolink as a service to its customers and may be used for informational purposes only by the customer. Isolink assumes no responsibility for errors or omissions in these materials or the information contained herein. Isolink may change its documentation, products, services, specifications or product descriptions at any time, without notice. Isolink makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Isolink assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Isolink products, information or materials, except as may be provided in Isolink Terms and Conditions of Sale. THE MTERILS, PRODUCTS ND INFORMTION RE PROVIDED S IS WITHOUT WRRNTY OF NY KIND, WHETHER EXPRESS, IMPLIED, STTUTORY, OR OTHERWISE, INCLUDING FITNESS FOR PRTICULR PURPOSE OR USE, MERCHNTBILITY, PERFORMNCE, QULITY OR NON-INFRINGEMENT OF NY INTELLECTUL PROPERTY RIGHT; LL SUCH WRRNTIES RE HEREBY EXPRESSLY DISCLIMED. ISOLINK DOES NOT WRRNT THE CCURCY OR COMPLETENESS OF THE INFORMTION, TEXT, GRPHICS OR OTHER ITEMS CONTINED WITHIN THESE MTERILS. ISOLINK SHLL NOT BE LIBLE FOR NY DMGES, INCLUDING BUT NOT LIMITED TO NY SPECIL, INDIRECT, INCIDENTL, STTUTORY, OR CONSEQUENTIL DMGES, INCLUDING WITHOUT LIMITTION, LOST REVENUES OR LOST PROFITS THT MY RESULT FROM THE USE OF THE MTERILS OR INFORMTION, WHETHER OR NOT THE RECIPIENT OF MTERILS HS BEEN DVISED OF THE POSSIBILITY OF SUCH DMGE. Customers are responsible for their products and applications using Isolink products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Isolink assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Isolink products outside of stated published specifications or parameters. Isolink is a trademark of Isolink Inc. in the United States and other countries. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners B Isolink Proprietary Information Products and Product Information are Subject to Change Without Notice pril 8, 27 7