FrelTec GmbH. Current Sensing Chip Resistor SMD

Size: px

Start display at page:

Download "FrelTec GmbH. Current Sensing Chip Resistor SMD"

Lillian Boyd
5 years ago
Views:

1 GmbH Mathildenstr. 10A Starnberg Germany SMD 11/22/2016 1/10 Freltec GmbH

2 SPECIFICATION Part Number * R001 * J * T05 ** E* Type Size Value Tolerance Packing Power Rating 018 : SMD Current Sensing Chip Resistor 02 : 0402 R = Decimal F : ±1% T05: Tape and reel for 5k pc (7 reel) A: 1/32W 03 : : 0805 Example: R010= 0,01Ohm R001= 1mOhm 06 : =0Ohm 10 : : : 2512 J : ±5% T10: Tape and reel for 10k pc (10 reel, "reel) T20: Tape and reel for 20k pc (13 reel, "reel) T40: Tape and reel for 40k pc (13 reel) E04: Tape and reel for 4k pc (7 reel) E08: Tape and reel for 8k pc (10 reel) ** 0402 available with T10, T20 and T40 all Paper Tape ** 0603 to 1210 available with T05, T10 and T20 all Paper Tape ** 2010 and 2512 available with E04 or E08, all Embossed Type * not all combination is possible B: 1/16W C: 1/10W D: 1/8W E: 1/4W G: 1/3W H: 1/2W I: 3/4W J: 1W L: 2W All products according to RoHS (2011/65/EU) 11/22/2016 2/10 GmbH

3 THICK FILM CHIP RESISTORS L 1 Alumina Substrate 2 Bottom Electrode 3 Top Electrode 4 Edge Electrode 5 Barrier Layer 6 External Electrode 7 Resistor Layer 8 Primary Overcoat 9 Secondary Overcoat Dimensions T W D2 D1 Size (Inch) L W T D1 D ,00±0,05 0,50±0,05 0,35±0,05 0,20±0,10 0,20±0, ,60±0,10 0,80±0,10 0,45±0,10 0,30±0,20 0,30±0, ,00±0,10 1,25±0,10 0,50±0,10 0,35±0,20 0,40±0, ,10±0,10 1,55±0,10 0,55±0,10 0,50±0,25 0,50±0, ,10±0,10 2,60±0,15 0,55±0,10 0,50±0,25 0,50±0, ,00±0,10 2,50±0,15 0,55±0,10 0,60±0,25 0,50±0, ,35±0,10 3,10±0,15 0,55±0,10 0,60±0,25 0,50±0,20 (unit: mm) Power Derating Curve For resistors operated in ambient temperatures above 70, power rating must be derated in accordance with the curve below. Operating temperature -55 C to +155 C Related Load [%] Temperature [ C] 11/22/2016 3/10 GmbH

4 Current Rating: Rated Current: The resistor shall have a DC continuous working current or a rms AC continuous working current at commercial-line frequency and wave form corresponding to the power rating, as determined from the following: I= Rated current [A] P= Power rating [W] R= Nominal resistance [Ω] Overload Voltage=2.5* (P*R) I THICK FILM CHIP RESISTORS Rating 018 Series P R Electrical Specifications Type Item Power Rating at 70 C Max. Operating Current Operating Temp. Range Resistance Range (mω) ±1% E24, E96 ±5% E24 TCR (PPM/ C) /16W 1,11A 1/10W 1,40A -55 ~ +155C /10W 1,23A /8W 2,50A /8W 3,53A 1/4W 5,00A 1/4W 5,00A 1/3W 5,77A 1/3W 5,77A 1/2W 7,07A 3/4W 8,66A 1W 10,0A 1W 10,0A 2W 14,1A Operating Voltage= (P*R) ; Overload Voltage=2.5* (P*R) ; Operating Current= (P/R) 11/22/2016 4/10 GmbH

5 SPECIFICATION R R no marking E96 and E24 (1%, 5%) 0805 to 2512 Examples R100=100mOhm R022 = 22mOhm SPECIFICATION Tape And Reel Package E96 and E24 (1%, 5%) % for 0603: 3 digits marking with under-line in E96 (non-including E24 series) 3 digits marking for E24 or R value suffix is zero in E96: R10=100mΩ R28=280mΩ 3 digits marking for E96: 243=243mΩ 511=511mΩ P0 E P2 D W F B D1 P1 D 1 only embossed type, min 1,4mm A In Accordance with EIA RS-481 Packing Size A B W E F P 0 P 1 P 2 D T 1 D 1 Paper Tape (T) Emboss ed Tape (E) ,65±0,10 1,15±0,1 8,0±0,2 1,75±0,1 3,50±0,05 4,00±0,10 2,00±0,05 2,00±0,05 1,50+0,1,-0 0,45±0, ,10±0,10 1,90±0,1 8,0±0,2 1,75±0,1 3,50±0,05 4,00±0,10 4,00±0,05 2,00±0,05 1,50+0,1,-0 0,70±0, ,60±0,10 2,40±0,2 8,0±0,2 1,75±0,1 3,50±0,05 4,00±0,10 4,00±0,05 2,00±0,05 1,50+0,1,-0 0,85±0, ,90±0,10 3,50±0,2 8,0±0,2 1,75±0,1 3,50±0,05 4,00±0,10 4,00±0,05 2,00±0,05 1,50+0,1,-0 0,85±0, ,90±0,10 3,50±0,2 8,0±0,2 1,75±0,1 3,50±0,05 4,00±0,10 4,00±0,05 2,00±0,05 1,50+0,1,-0 0,85±0, ,8±0,10 5,5±0,10 12,0±0,3 1,75±0,1 5,5±0,05 4,00±0,10 4,00±0,1 2,00±0,05 1,50+0,1, -0 1,2 +0,ଶହ 1, ,5±0,10 6,7±0,10 12,0±0,3 1,75±0,1 5,5±0,05 4,00±0,10 4,00±0,1 2,00±0,05 1,50+0,1, -0 1,2 +0,ଶହ 1,5 Lead Dimensions: 11/22/2016 5/10 GmbH

6 Cover Tape Peel off Strength Specifications: 0402 => 0,07~0,5N (7,1~51gf) 0603, 0805, 1206, 1210, 2512 => 0,07~0,7N (7,1~71.4gf) Size Reel Diameter ΦA ΦN ΦC G T inch 178,5±1, /-0 13,0±0,2 9,0±0,5 12,5±0,5 10 inch 254±1 100±0,5 13,0±0,2 9,5±0,5 13,5±0,5 13 inch 330±1 100±0,5 13,0±0,2 9,5±0,5 13,5±0,5 7 inch 178,5±1, /-0 13,0±0,5 13,0±0,5 15,5±0,5 10 inch 250±1 62±0,5 13,0±0,5 12,5±0,5 16,5±0,5 in mm Stock period The temperature condition must be controlled at 25± 3 C, the R.H. must be controlled below 80% RH before soldering. The stock can maintain quality level in 12 month. 11/22/2016 6/10 GmbH

7 Lead Free Reflow Soldering Profile Wave soldering Remark: The peak temperature of soldering heat is 260 C for 10 seconds. Soldering Iron: Temperature 410 C, dwell time shall be less than 5 seconds. 11/22/2016 7/10 Freltec GmbH

Recommended Land Pattern Design (For Reflow Soldering): Size A B C 0402 0,50 1,4 0,60 0603 0,90 2,1 0,90 0805 1,20 2,6

8 Recommended Land Pattern Design (For Reflow Soldering): Size A B C ,50 1,4 0, ,90 2,1 0, ,20 2,6 1, ,00 3,8 1, ,00 3,8 2, ,80 5,6 2, ,80 7,0 3,50 Unit: mm 11/22/2016 8/10 GmbH

9 Environmental Characteristics Item Temperature Coefficient of Resistance (T.C.R.) As Spec. Requirement ±1% ±5% Short Time Overload (1,0%+0,05Ω) (2,0%+0,05Ω) Insulation Resistance Endurance 10G (1,0%+0,10Ω) (2,0%+0,10Ω) Damp Heat with Load (1,0%+0,10Ω) (2,0%+0,10Ω) Dry Heat (1,0%+0,05Ω) (1,5%+0,10Ω) Bending Strength (1,0%+0,05Ω) (1,0%+0,05Ω) Solderability Resistance to Soldering Heat Voltage Proof Leaching Rapid Change of Temperature >95% coverage (0,5%+0,05Ω) (1,0%+0,05Ω) No breakdown or flashover Individual leaching area 5% Total leaching area 10% (0,5%+0,05Ω) (1,0%+0,05Ω) Test Method JIS C IEC C~+125C, 25C is the reference temperature JIS C IEC ,5 times RCWV or Max. overload voltage for 5 seconds, 2 seconds for high power series JIS C IEC Max. overload voltage for 1 minute JIS C IEC C, Max. working voltage for 1000 hrs with 1,5 hrs ON and 0,5 hrs OFF JIS C C, 90~95% R.H., Max. working voltage for 1000 hrs with 1,5 hrs ON and 0,5 hrs OFF JIS C IEC at +155C for 1000 hrs JIS C IEC Bending once for 5 seconds 2010, 2512 sizes: 2mm Other sizes: 3mm JIS C IEC C for 3 seconds JIS C IEC C for 10 seconds JIS C IEC ,42 times RCWV (RMS) for 1 minute JIS C IEC C for 30 seconds JIS C IEC C to +155C, 5 cycles 11/22/2016 9/10 GmbH

10 Published by GmbH Mathildenstr. 10A; Starnberg; Germany 2016 GmbH. All Rights Reserved. The following applies to all products named in this publication: 1. The information describes the type of component and shall not be considered as assured characteristics. 2. Terms of delivery and rights to change design reserved. 3. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. Nevertheless, we explicitly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether a product with the properties described in the product specification is suitable for use in a particular customer application. 4. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 5. The warnings, cautions and product-specific notes must be observed. 6. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous ). Useful information on this will be found in our Material Data Sheets. Should you have any more detailed questions, please contact our sales offices. 7. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true for the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 8. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the General conditions for the supply of products and services of the electrical and electronics industry published by the German Electrical and Electronics Industry Association (ZVEI), available at 9. As far as patents or other rights of third parties are concerned, liability is only assumed for components per se, not for applications, processes and circuits implemented within components or assemblies. 10. The trade name is a trademark registered or pending in Europe and in other countries. 11/22/ /10 GmbH

FrelTec GmbH. Current Sensing Chip Resistor SMD

FrelTec GmbH. Current Sensing Chip Resistor SMD GmbH Mathildenstr. 10A 82319 Starnberg Germany SMD 6/8/2015 1/13 Freltec GmbH www.freltec.com SPECIFICATION Part Number 017 05 * R001 * J * T05 ** D E Size Value Tolerance Packing TCR Power Rating 017