Specifications. S&C BankGuard Plus Controls. For Substation Capacitor Banks and Shunt Reactors. Conditions of Sale

Size: px
Start display at page:

Download "Specifications. S&C BankGuard Plus Controls. For Substation Capacitor Banks and Shunt Reactors. Conditions of Sale"

Transcription

1 For Substation Capacitor Banks and Shunt Reactors Specifications Conditions of Sale STANDARD: Seller s standard conditions of sale set forth in Price Sheet 150 apply, except as modified by the SPE CIAL WARRANTY PROVISIONS, and WARRANTY QUAL IFICATIONS sections in this specification bulletin. SPECIAL TO THIS PRODUCT: INCLUSIONS: The S&C BankGuard Plus Control protects substation shunt capacitor banks from overvoltage stress and provides turn-to-turn winding fault protection for shunt reactors. The BankGuard Plus has the sensitivity to detect and alarm on the loss of individual capacitor units or developing winding faults. With the capability to detect and alarm upon the loss of the first failed capacitor unit in a bank, the BankGuard Plus offers users a major advantage: The failed unit can be replaced at a convenient, planned time... not on an urgent basis, after subsequent capacitor units have failed and the bank has been locked out. An adjustable time delay is utilized to avoid false alarms due to transient dis turbances. Nuisance alarms and lockouts due to the induction of high voltages during routine bank de-energi zation are also eliminated. The BankGuard Plus can detect and compensate for system voltage and capacitor-bank or reactor unbalance resulting from manufacturing-tolerance variations among the individual capacitor units and reactor phase windings.f In large-size capacitor banks, such unbalance voltages can introduce significant errors in, or even overpower, the voltage signal created by the loss of individual capacitor units. The BankGuard Plus includes filtering to attenuate spurious transients and harmonics. The BankGuard Plus further includes gross-overvolt age logic which bypasses the lockout-level and timing-control logic to achieve fast capacitor-bank or reactor iso lation in the event of a flashover of a series group in the bank or flashover of a significant portion of a phase wind ing. The BankGuard Plus is suitable for standard 19-inch relay rack mounting. An optional bezel is available for flush mounting in a switchboard or control console. The BankGuard Plus is a direct replacement for S&C Automatic Control Devices Types UP, GP, and UPR. Terminal strip connections are identical with those of the Type UP and all connections for Types GP and UPR are accommodated. Protection of Ungrounded, Wye-Connected Shunt Capacitor Banks, Including Double-Wye Banksl In these applications, the BankGuard Plus monitors the voltage between the neutral (common) connection of the capacitor bank and ground with a 15-volt-ampere S&C Potential Device. As successive individual capacitor units in a series group of the bank are isolated by their respec tive fuses, the surviving capacitor units in the group are protected against cascading voltage overstress by the BankGuard Plus, which isolates and locks out the entire bank when a predetermined neutral-to-ground voltage Protection of Grounded, Wye-Connected Shunt Capacitor Banks Consisting of Two or More Series Groups per Phase In these applications, the BankGuard Plus monitors, for each phase of the capacitor bank, the voltage between an intermediate tap point and ground with a 30-volt-ampere S&C Potential Device. As successive individual capacitor units in a series group of the bank are isolated by their respective fuses, the surviving capacitor units in the group are protected against cascading voltage overstress by the BankGuard Plus, which isolates and locks out the entire bank when a predetermined tap point-to-ground voltage Protection of Ungrounded, Wye-Connected Shunt Reactorsl In these applications, the BankGuard Plus monitors the voltage between the neutral (common) connection of the reactor and ground with a 15-volt-ampere S&C Potential Device. If a turn-to-turn fault develops in a phase winding, the BankGuard Plus isolates and locks out the entire reactor when a predetermined neutral-to-ground voltage f For proper unbalance, the system-derived voltages monitored by the BankGuard Plus must be obtained by means of 30-volt-ampere S&C Potential Devices or voltage transformers connected to the segment of station bus to which the capacitor bank or reactor is tapped. Connecting circuits from the potential devices or voltage transformers to the BankGuard Plus must be free of variable loads, variable voltage drops, and ground loops so that the voltages monitored accurately represent the magnitude and phase angle of the bus voltages. l For applications where the source is a delta-connected tertiary transformer winding, a grounded-wye broken-delta voltage-transformer bank with shunt resistor referred to as a high-impedance grounding transformer (normally required for ground-fault detection) is required to maintain the stability of phase-to-ground voltage relationships for all but fault conditions. Otherwise spurious signal voltages could appear at the neutral of, and result in isolation of, the capacitor bank or reactor. The BankGuard Plus includes an unbalance that detects and compensates for up to 10% error voltage appearing between the neutral and ground. October 29, 2012 S&C Electric Company Specification Bulletin

2 Conditions of Sale Continued SPECIFICATION NOTES: S&C BankGuard Plus Controls have been tested to verify their capability to withstand, without misoperation or damage, surge-voltage tests as follows: 1. The ANSI Surge Withstand Capability Test (ANSI Standard C37.90a, 1974). The specified surges are applied at all control device terminals. 2. A 5-kV, 3.75-joule capacitive-discharge test with surge applied at all control device terminals. This additional test represents a surge level well in excess of those normally encountered in control wiring in utility environments. To prevent damage to the control device in the event that surges which exceed factory-tested levels are encountered, S&C s control-circuit fusing recommenda tions must be followed. The required fuse blocks and fuses are furnished with the control devices. If frequent surges in excess of factory-tested levels are anticipated, S&C should be advised as to the severity of the surges so that special recommendations can be made. For all grounded-wye capacitor-bank installations the following steps must be taken to ensure that the control device is not subjected to surges in excess of the level defined in ANSI Standard C37.90a: 1. Adequate shielding must be provided for control-cir cuit wiring. 2. For installations involving two or more grounded-wye capacitor banks in the same station, their neutrals must be interconnected and grounded at a single point only. Additionally, it is recommended (although not required) that the capacitor-bank switching devices be equipped with pre-insertion impedances for reduction of inrush current and transient voltage disturbances associated with capacitor-switching applications. EXCLUSIONS: BankGuard Plus Controls do not include voltage-monitoring devices. Refer to Specification Bulletin for information on S&C Potential Devices. SPECIFICATION DEVIATIONS: Refer to Options table on page 4. SPECIAL WARRANTY PROVISIONS: The standard warranty contained in seller s standard conditions of sale, as set forth in Price Sheet 150, applies to BankGuard Plus Controls, except that the first paragraph of said warranty is replaced by the following: (1) General: Seller warrants to immediate purchaser or end user for a period of 10 years from the date of shipment that the equipment delivered will be of the kind and quality specified in the contract description and will be free of defects of workmanship and material. Should any failure to conform to this warranty appear under proper and normal use within ten years after the date of shipment the seller agrees, upon prompt notification thereof and confirmation that the equipment has been stored, installed, operated, inspected, and maintained in accordance with recommendations of the seller and standard industry practice, to correct the nonconformity either by repairing any damaged or defective parts of the equipment or (at seller s option) by shipment of necessary replacement parts. The seller s warranty does not apply to any equipment that has been disassembled, repaired, or altered by anyone other than the seller. This limited warranty is granted only to the immediate purchaser or, if the equipment is purchased by a third party for installation in third-party equipment, the end user of the equipment. The seller s duty to perform under any warranty may be delayed, at the seller s sole option, until the seller has been paid in full for all goods purchased by the imme diate purchaser. No such delay shall extend the war ranty period. Replacement parts provided by seller or repairs performed by seller under the warranty for the original equipment will be covered by the above special warranty provision for its duration. Replacement parts purchased separately will be covered by the above special warranty provision. WARRANTY QUALIFICATIONS: Warranty of Bank Guard Plus Controls is contingent upon the installation, configuration, and use of the control or software in accordance with S&C s applicable instruction sheets. This warranty does not apply to major components not of S&C manufacture, such as batteries, communication devices, and remote terminal units. However, S&C will assign to immediate purchaser or end user all manufacturers warranties that apply to such major components. END USER LICENSE AGREEMENT: End user is granted a nontransferable, non-sublicensable, nonexclusive license to use the IntelliLink Remote Setup Software and/or other Software furnished with S&C BankGuard Plus Controls only upon acceptance of all the terms and conditions of the seller s end user license agreement set forth in Price Sheet S&C Specification Bulletin

3 How to Order 1. Control a. Select the catalog number of the desired control from the table on page 4. b. Add Suffix -B to the catalog number if the optional bezel is desired. See the Options table on page 4. c. For calibration purposes, include information on the neutral-, tap-, and/or system-voltage devices used, i.e., catalog number of S&C Potential Device(s), or primary voltage rating and turns ratio of voltage transformer(s) Plus nominal voltage of voltage-transformer secondary circuit.m 2. Example For an S&C BankGuard Plus Control for application on an ungrounded capacitor bank connected to a sys tem rated 138 kv nominal, specify: Catalog Number , for use with one S&C 15-volt-ampere S&C Potential Device, Catalog Number 81576R1, and,, three 30-volt-ampere S&C Potential Devices, Catalog Number 81349R6-T (or three voltage transformers with a primary rating of 80,500 volts, turns ratio of 1200:1, and secondary cir cuit rated volts), for application on a system rated 138 kv nominal. m If no information on the neutral-, tap-, and/or system-voltage devices is specified, the device will be shipped marked for field calibra tion. S&C Specification Bulletin

4 Bankguard Plus Controls Diagram Control Application1 Switch Operator Potential Device BankGuard Plus Control Control- Source Voltage Catalog Number Page Reference for Dimensional Information Net Wt., Lbs. (Kg.) For protection of ungrounded, wyeconnected and double-wye-connected shunt capacitor banks2 For protection of grounded, wyeconnected shunt capacitor banks 48 to 250 Vdc or 120 to 240 Vac, 50 or 60 Hz (4.95) For protection of ungrounded, wyeconnected shunt reactors2 1 For installations in the vicinity of 345-kV or 500-kV circuits, refer to the nearest S&C Sales Office. 2 For applications where the source is a delta-connected tertiary transformer winding, a grounded-wye broken-delta voltage-transformer bank with shunt resistor referred to as a high-impedance grounding transformer (normally required for ground-fault detection) is required to maintain the stability of phase-to-ground voltage relationships for all but fault conditions. Otherwise spurious signal voltages could appear at the neutral of, and result in isolation of, the capacitor bank or reactor. S&C BankGuard Plus Controls include an unbalance that detects and compensates for up to 10% error voltage appearing between the neutral and ground. n S&C Potential Device rated 15 volt-amperes having a system voltage rating as follows: Nominal Source Voltage, kv below S&C Potential Device System Voltage Rating, kv, Nom The 15-VA Potential Device is recommended. If a 30-VA Potential Device is used for neutral-to-ground it must either be equipped with factory-adjusted calibration device, Catalog Number Suffix -T, or a locally installed 480-ohm, 50-watt resistor may be used to terminate the secondary output of the 30-VA Potential Device. l S&C Potential Device rated 30 volt-amperes equipped with factoryadjusted calibration device, Catalog Number Suffix -T. The minimum system voltage rating of the potential device is derived by calculating the voltage appearing between the intermediate tap points and ground and multiplying this value by 3. Since S&C Potential Devices are not of instrument-class accuracy, their performance in intermediate-tap-point voltage-monitoring applications on very-large-sized grounded, wye-connected shunt capacitor banks may not be entirely satisfactory, especially if it is desired to obtain an alarm signal upon the loss of a single capacitor unit. Specifically, this alarm signal setting on banks consisting of more than 150 capacitor units or more than 5 series groups per phase (often the case where system voltage is higher than 138 kv) may possibly lead to nuisance alarms under severe rainfall conditions. In cases where such false operations are of especial concern, higher-accuracy devices such as voltage transformers or capacitor-coupled voltage transformers are recommended. The minimum system voltage rating of these devices is derived by calculating the voltage appearing between the intermediate tap points and ground and multiplying this value by 3. Adequate damping resistance must be connected across each voltage-transformer secondary circuit; viz., a resistance load equal to at least 2% of the transformer thermal rating. w S&C Potential Device rated 30 volt-amperes (or voltage transformer) having a system voltage rating equal to the voltage of the system to which the capacitor bank or reactor is connected. If capacitor-unit or reactor phase-winding manufacturing tolerance variations are of specific con cern, a single potential device or voltage transformer is required. If sys tem voltage unbalance is also of concern in ungrounded capacitor bank or reactor applications, three potential devices or voltage transformers are required. Options Item Suffix to be Added to Control Catalog Number Mounting Bezel for Flush Mounting of BankGuard Plus Control, 220 W 80 H Z\v0 D -B 4 S&C Specification Bulletin

5 BankGuard Plus Dimensions in inches (mm) (435) 5.25 (133.4) (372.9) (354.8) 1.50 (38.1) (482.6) (460.5) 5.25 (133.4) 2.25 (57.2) UNBALANCE COMPENSATION LOCKOUT LEVEL 4.97 (126.2) PUSH TO SET PUSH TO READ PUSH TO RESET S&C Specification Bulletin

ISO Rules Part 500 Facilities Division 502 Technical Requirements Section Aggregated Generating Facilities Technical Requirements

ISO Rules Part 500 Facilities Division 502 Technical Requirements Section Aggregated Generating Facilities Technical Requirements Division 502 Technical Applicability 1(1) Section 502.1 applies to: Expedited Filing Draft August 22, 2017 the legal owner of an aggregated generating facility directly connected to the transmission system

More information

INSTRUCTIONS For Installation and Operation

INSTRUCTIONS For Installation and Operation S&C Bankgard Relay - Type LUC Ungrounded, Wye-Connected Shunt NSTRUCTONS For nstallation and Operation 1 TABLE OF CONTENTS Section Page Number Section Page Number NTRODUCTON.....l LOCKOUT-TMER ADJUSTMENT...

More information

ISO Rules Part 500 Facilities Division 502 Technical Requirements Section Wind Aggregated Generating Facilities Technical Requirements

ISO Rules Part 500 Facilities Division 502 Technical Requirements Section Wind Aggregated Generating Facilities Technical Requirements Applicability 1(1) Section 502.1 applies to the ISO, and subject to the provisions of subsections 1(2), (3) and (4) to any: (a) a new wind aggregated generating facility to be connected to the transmission

More information

POWER FACTOR CORRECTION. HARMONIC FILTERING. MEDIUM AND HIGH VOLTAGE SOLUTIONS.

POWER FACTOR CORRECTION. HARMONIC FILTERING. MEDIUM AND HIGH VOLTAGE SOLUTIONS. POWER FACTOR CORRECTION. HARMONIC FILTERING. MEDIUM AND HIGH VOLTAGE SOLUTIONS. This document may be subject to changes. Contact ARTECHE to confirm the characteristics and availability of the products

More information

Wind Power Facility Technical Requirements CHANGE HISTORY

Wind Power Facility Technical Requirements CHANGE HISTORY CHANGE HISTORY DATE VERSION DETAIL CHANGED BY November 15, 2004 Page 2 of 24 TABLE OF CONTENTS LIST OF TABLES...5 LIST OF FIGURES...5 1.0 INTRODUCTION...6 1.1 Purpose of the Wind Power Facility Technical

More information

S&C Series 2000 Circuit-Switchers Outdoor Transmission (69 kv through 230 kv)

S&C Series 2000 Circuit-Switchers Outdoor Transmission (69 kv through 230 kv) Outdoor Transmission (69 kv through 230 kv) Detailed Functional Specification Guide 1.0 GENERAL 1.01 The circuit-switcher shall conform to the following specification. 1.02 The circuit-switcher shall be

More information

Power Processor - Series 700F 10KVA to 150KVA

Power Processor - Series 700F 10KVA to 150KVA Power Processor - Series 700F 10KVA to 150KVA Power Conditioning and Regulation for Commercial & Industrial Equipment General Specifications PART 1 - GENERAL 1.1 DESCRIPTION This specification defines

More information

Specifications. S&C Circuit-Switcher Mark V Outdoor Transmission (34.5 kv through 345 kv) Conditions of Sale SPECIAL TO THIS PRODUCT:

Specifications. S&C Circuit-Switcher Mark V Outdoor Transmission (34.5 kv through 345 kv) Conditions of Sale SPECIAL TO THIS PRODUCT: S&C Circuit-Switcher Mark V Outdoor Transmission (34.5 kv through 345 kv) Specifications Conditions of Sale STANDARD: Seller s standard conditions of sale set forth in Price Sheet 150 apply, except as

More information

TECHNICAL DESCRIPTION

TECHNICAL DESCRIPTION TECHNICAL DESCRIPTION A.M. BROADCAST TRANSMITTER SENDER AM 3000 SS June 2001-1- Rev. B TRANSMITTER CHARACTERISTICS 1. BASIC OFFER The basic offer includes: One AM3000SS A.M. Medium Wave Solid State Broadcast

More information

PRODUCT SPECIFICATION FOR A 15 AND 75 kva, THREE PHASE MODULAR POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING (Varian)

PRODUCT SPECIFICATION FOR A 15 AND 75 kva, THREE PHASE MODULAR POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING (Varian) PRODUCT SPECIFICATION FOR A 15 AND 75 kva, THREE PHASE MODULAR POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING (Varian) 1.0 General This specification covers the electrical characteristics and

More information

Rev.8.8 SSRMAN-1P SERIES USERS MANUAL SSR INTELLIGENT PHASE ANGLE CONTROL MODULE COPYRIGHT 2015 NUWAVE TECHNOLOGIES, INC.

Rev.8.8 SSRMAN-1P SERIES USERS MANUAL SSR INTELLIGENT PHASE ANGLE CONTROL MODULE COPYRIGHT 2015 NUWAVE TECHNOLOGIES, INC. Rev.8.8 MAN-1P SERIES USERS MANUAL INTELLIGENT PHASE ANGLE CONTROL MODULE COPYRIGHT 2015 MAN-1P Users Manual Page 2 TABLE OF CONTENTS 1. Ordering Codes... 2 2. Description... 3 2.1 Features... 3 3. Installation

More information

Tertiary Winding Design in wye-wye Connected Transformers Restricted Siemens Energy 2013 All rights reserved.

Tertiary Winding Design in wye-wye Connected Transformers Restricted Siemens Energy 2013 All rights reserved. Pomona, CA, May 24 & 25, 2016 Tertiary Winding Design in wye-wye Connected Transformers Scope of Presentation > Tertiary vs. Stabilizing Winding? Tertiary vs. Stabilizing Winding? Need for Stabilizing

More information

ABB Automation, Inc. Substation Automation & Protection Division Coral Springs, FL Allentown, PA

ABB Automation, Inc. Substation Automation & Protection Division Coral Springs, FL Allentown, PA ABB Automation, Inc. Substation Automation & Protection Division Coral Springs, FL Allentown, PA Instruction Leaflet 41-348.1H Effective: November 1997 Supersedes I.L. I.L. 41-348.1G, Dated January 1985

More information

1 INTRODUCTION ORDER CODE / INFORMATION

1 INTRODUCTION ORDER CODE / INFORMATION INTRODUCTION ORDER CODE / INFORMATION 269/269Plus * * * * * * 269/269Plus SV D/O.4 ORDER CODE / INFORMATION Motor management relay Standard version Drawout version Phase CT Ground CT (required for D/O

More information

BE1-87G VARIABLE PERCENTAGE DIFFERENTIAL RELAY

BE1-87G VARIABLE PERCENTAGE DIFFERENTIAL RELAY BE1-87G VARIABLE PERCENTAGE DIFFERENTIAL RELAY The BE1-87G is a single or three-phase solid-state variable percentage differential relay designed to provide selective, high-speed, differential protection

More information

10. DISTURBANCE VOLTAGE WITHSTAND CAPABILITY

10. DISTURBANCE VOLTAGE WITHSTAND CAPABILITY 9. INTRODUCTION Control Cabling The protection and control equipment in power plants and substations is influenced by various of environmental conditions. One of the most significant environmental factor

More information

SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches

SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches PART 1 GENERAL 1.01 Scope Furnish and install automatic transfer switches (ATS) with number of poles, amperage, voltage, and withstand

More information

BUCK-BOOST TRANSFORMERS

BUCK-BOOST TRANSFORMERS Where Are Buck-Boost Transformers Used? A typical buck-boost application is 120 volts in, 12 volts out for low voltage lighting or control circuitry. In most applications, this low voltage transformer

More information

Generation Interconnection Requirements at Voltages 34.5 kv and Below

Generation Interconnection Requirements at Voltages 34.5 kv and Below Generation Interconnection Requirements at Voltages 34.5 kv and Below 2005 March GENERATION INTERCONNECTION REQUIREMENTS AT 34.5 KV AND BELOW PAGE 1 OF 36 TABLE OF CONTENTS 1. INTRODUCTION 5 1.1. Intent

More information

2 Grounding of power supply system neutral

2 Grounding of power supply system neutral 2 Grounding of power supply system neutral 2.1 Introduction As we had seen in the previous chapter, grounding of supply system neutral fulfills two important functions. 1. It provides a reference for the

More information

Table of Contents. Introduction... 1

Table of Contents. Introduction... 1 Table of Contents Introduction... 1 1 Connection Impact Assessment Initial Review... 2 1.1 Facility Design Overview... 2 1.1.1 Single Line Diagram ( SLD )... 2 1.1.2 Point of Disconnection - Safety...

More information

Low Voltage Power Factor Correction Equipment Specifications Automatic, Automatic Detuned, Automatic Tuned

Low Voltage Power Factor Correction Equipment Specifications Automatic, Automatic Detuned, Automatic Tuned Low Voltage Power Factor Correction Equipment Specifications Automatic, Automatic Detuned, Automatic Tuned Part 1 - General Scope and Product Description 1.0 This specification contains the minimum design

More information

Fixed Series Compensation

Fixed Series Compensation Fixed Series Compensation High-reliable turnkey services for fixed series compensation NR Electric Corporation The Fixed Series Compensation (FSC) solution is composed of NR's PCS-9570 FSC control and

More information

PIRANHA 3 (3-phase, Power Conditioning Voltage Regulator)

PIRANHA 3 (3-phase, Power Conditioning Voltage Regulator) PRODUCT SPECIFICATION FOR A 15 THRU 500 kva, THREE PHASE, MODULAR POWER REGULATOR AND CONDITIONER PIRANHA 3 (3-phase, Power Conditioning Voltage Regulator) 1.0 General This specification covers the electrical

More information

HPS Universal BUCK-BOOST TRANSFORMERS

HPS Universal BUCK-BOOST TRANSFORMERS BUCK-BOOST TRANSFORMERS Single and Three Phase Potted Buck-Boost Transformers Buck-Boost Applications & Standard Specification... 80 Selecting Buck-Boost Transformers... 81 Single Phase Selection Tables...

More information

80i-600A AC Current Probe

80i-600A AC Current Probe x Instruction Sheet 80i-600A AC Current Probe INTRODUCTION The Model 80i-600A is a clamp-on ac current probe designed to extend the current measuring capability of an ac current meter to 600 amperes. A

More information

Rev /13 SSRMAN-1B SERIES USERS MANUAL SSR INTELLIGENT BURST FIRING CONTROL COPYRIGHT 2013 NUWAVE TECHNOLOGIES, INC.

Rev /13 SSRMAN-1B SERIES USERS MANUAL SSR INTELLIGENT BURST FIRING CONTROL COPYRIGHT 2013 NUWAVE TECHNOLOGIES, INC. Rev.2.2 12/13 MAN-1B SERIES USERS MANUAL INTELLIGENT BURST FIRING CONTROL COPYRIGHT 2013 MAN-1B Users Manual Page 2 TABLE OF CONTENTS 1. Ordering Codes... 2 2. Description... 2 2.1 Features... 3 3. Installation

More information

OPERATING, METERING AND EQUIPMENT PROTECTION REQUIREMENTS FOR PARALLEL OPERATION OF LARGE-SIZE GENERATING FACILITIES GREATER THAN 25,000 KILOWATTS

OPERATING, METERING AND EQUIPMENT PROTECTION REQUIREMENTS FOR PARALLEL OPERATION OF LARGE-SIZE GENERATING FACILITIES GREATER THAN 25,000 KILOWATTS OPERATING, METERING AND EQUIPMENT PROTECTION REQUIREMENTS FOR PARALLEL OPERATION OF LARGE-SIZE GENERATING FACILITIES GREATER THAN 25,000 KILOWATTS AND MEDIUM-SIZE FACILITIES (5,000-25,000KW) CONNECTED

More information

INSTALLATION AND MAINTENANCE MANUAL FOR GROUND MONITOR GM-250 COPYRIGHT 1983 AMERICAN MINE RESEARCH, INC.

INSTALLATION AND MAINTENANCE MANUAL FOR GROUND MONITOR GM-250 COPYRIGHT 1983 AMERICAN MINE RESEARCH, INC. INSTALLATION AND MAINTENANCE MANUAL FOR GROUND MONITOR GM-250 COPYRIGHT 1983 AMERICAN MINE RESEARCH, INC. MANUAL PART NUMBER 180-0036 ORIGINAL: 1-17-83 REVISION: B (8-26-86) NOT TO BE CHANGED WITHOUT MSHA

More information

Section 16621A - AUTOMATIC TRANSFER SWITCH. Part 1 General

Section 16621A - AUTOMATIC TRANSFER SWITCH. Part 1 General Section 16621A - AUTOMATIC TRANSFER SWITCH Part 1 General 1.01 One 600 Amp, 3 Phase, 480 Volt Automatic Transfer Switch (ATS) shall be provided with gasketed enclosure. The ATS shall consist of an inherently

More information

OPERATING, METERING, AND EQUIPMENT PROTECTION REQUIREMENTS FOR PARALLEL OPERATION OF LARGE-SIZE GENERATING FACILITIES GREATER THAN 2,000 KILOWATTS

OPERATING, METERING, AND EQUIPMENT PROTECTION REQUIREMENTS FOR PARALLEL OPERATION OF LARGE-SIZE GENERATING FACILITIES GREATER THAN 2,000 KILOWATTS OPERATING, METERING, AND EQUIPMENT PROTECTION REQUIREMENTS FOR PARALLEL OPERATION OF LARGE-SIZE GENERATING FACILITIES GREATER THAN 2,000 KILOWATTS CONNECTED TO THE DISTRIBUTION SYSTEM ORANGE AND ROCKLAND

More information

Power-Sure 700. Technical Data TD158001EN. Contents

Power-Sure 700. Technical Data TD158001EN. Contents Technical Data TD158001EN Power-Sure 700 Supersedes August 2015 Contents Description Page General description... 2 Power-Sure 700 benefits.... 2 Specifications... 3 Industry standards and certifications...

More information

Numbering System for Protective Devices, Control and Indication Devices for Power Systems

Numbering System for Protective Devices, Control and Indication Devices for Power Systems Appendix C Numbering System for Protective Devices, Control and Indication Devices for Power Systems C.1 APPLICATION OF PROTECTIVE RELAYS, CONTROL AND ALARM DEVICES FOR POWER SYSTEM CIRCUITS The requirements

More information

ADA416-XLR DISTRIBUTION AMPLIFIERS OPERATING AND MAINTENANCE MANUAL

ADA416-XLR DISTRIBUTION AMPLIFIERS OPERATING AND MAINTENANCE MANUAL ADA416-XLR DISTRIBUTION AMPLIFIERS OPERATING AND MAINTENANCE MANUAL Copyright 2015, ATI Audio Inc. DESCRIPTION Your ADA416-XLR provides four independent one-in by four-out circuit groups. A four-output

More information

Specifications. S&C Cypoxy Insulators. Indoor and Outdoor Distribution (4.8 kv through 46 kv) Conditions of Sale

Specifications. S&C Cypoxy Insulators. Indoor and Outdoor Distribution (4.8 kv through 46 kv) Conditions of Sale Indoor and Outdoor Distribution (.8 kv through kv) Specifications Conditions of Sale STANDARD: Seller s standard conditions of sale set forth in Price Sheet 150 apply. SPECIAL TO THIS PRODUCT: INCLUSIONS:

More information

BC145 SIGNAL ISOLATOR BOARD

BC145 SIGNAL ISOLATOR BOARD BC145 SIGNAL ISOLATOR BOARD 4/17 Installation & Operating Manual MN1373 Any trademarks used in this manual are the property of their respective owners. Important: Be sure to check www.baldor.com to download

More information

PRODUCT/TEST MANUAL 2V162K12 VOLTAGE REGULATOR RELAY

PRODUCT/TEST MANUAL 2V162K12 VOLTAGE REGULATOR RELAY Sheet 1 of 15 TEST DATE: CUSTOMER: SERIAL NO: OLTC ACKNOWLEDGE SETUP AUTOMATIC or FEEDBACK CONTROL PRODUCT/TEST MANUAL 2V162K12 VOLTAGE REGULATOR RELAY Issue Date Level A 06/01/1997 Initial issue. Summary

More information

TEGAM INC. MODEL DSRS-5DA DECADE SYNCO/RESOLVER STANDARD

TEGAM INC. MODEL DSRS-5DA DECADE SYNCO/RESOLVER STANDARD TEGAM INC. MODEL DSRS-5DA DECADE SYNCO/RESOLVER STANDARD Instruction Manual PN# 500783-349 Publication Date: Novermber 2007 REV. A NOTE: This user s manual was as current as possible when this product

More information

BE1-67N GROUND DIRECTIONAL OVERCURRENT RELAY FEATURES ADDITIONAL INFORMATION. FUNCTIONS AND FEATURES Pages 2-4. APPLICATIONS Page 2

BE1-67N GROUND DIRECTIONAL OVERCURRENT RELAY FEATURES ADDITIONAL INFORMATION. FUNCTIONS AND FEATURES Pages 2-4. APPLICATIONS Page 2 BE1-67N GROUND DIRECTIONAL OVERCURRENT RELAY The BE1-67N Ground Directional Overcurrent Relay provides ground fault protection for transmission and distribution lines by sensing the direction and magnitude

More information

ASX SERIES PACIFIC OPERATION MANUAL AC POWER SOURCE POWER SOURCE

ASX SERIES PACIFIC OPERATION MANUAL AC POWER SOURCE POWER SOURCE ASX SERIES AC POWER SOURCE OPERATION MANUAL PACIFIC POWER SOURCE ASX-SERIES OPERATION MANUAL FOR THE MODELS 115-ASX, 120-ASX 140-ASX, 160-ASX 315-ASX, 320-ASX 345-ASX, 360-ASX 390-ASX, 3120-ASX PPS PART

More information

McPherson Voltage Regulators 4501 NW 27 Ave Miami FL

McPherson Voltage Regulators 4501 NW 27 Ave Miami FL McPherson Voltage Regulators 4501 NW 27 Ave Miami FL 33142 305-634-1511 To avoid of possible personal injury or equipment damage read and understand this manual before installation. (A.V.R) 208 / 380 /

More information

7. INSPECTION AND TEST PROCEDURES

7. INSPECTION AND TEST PROCEDURES 7.1 Switchgear and Switchboard Assemblies A. Visual and Mechanical Inspection 1. Compare equipment nameplate data with drawings and specifications. 2. Inspect physical and mechanical condition. 3. Inspect

More information

ESB National Grid Transmission Planning Criteria

ESB National Grid Transmission Planning Criteria ESB National Grid Transmission Planning Criteria 1 General Principles 1.1 Objective The specific function of transmission planning is to ensure the co-ordinated development of a reliable, efficient, and

More information

APPLICATION: The heart of the system is a DSR 100 Digital Static Regulator used in conjunction with standard SCR based rectifier bridges.

APPLICATION: The heart of the system is a DSR 100 Digital Static Regulator used in conjunction with standard SCR based rectifier bridges. APPLICATION: Basler Electric offers a New Line of digitally controlled brush (static) or brushless excitation systems designed for use with existing Hydro, Gas as well as Diesel driven generators requiring

More information

DA208 & DA416 DISTRIBUTION AMPLIFIERS OPERATING AND MAINTENANCE MANUAL

DA208 & DA416 DISTRIBUTION AMPLIFIERS OPERATING AND MAINTENANCE MANUAL DA208 & DA416 DISTRIBUTION AMPLIFIERS OPERATING AND MAINTENANCE MANUAL Copyright 2011, ATI Audio Inc. DESCRIPTION Your DA208 or DA416 provides two (DA208) or four (DA416) independent one-in by four-out

More information

Model 113 Scintillation Preamplifier Operating and Service Manual

Model 113 Scintillation Preamplifier Operating and Service Manual Model 113 Scintillation Preamplifier Operating and Service Manual Printed in U.S.A. ORTEC Part No. 717560 1202 Manual Revision B Advanced Measurement Technology, Inc. a/k/a/ ORTEC, a subsidiary of AMETEK,

More information

MODEL 3810/2 Line Impedance Stabilization Network

MODEL 3810/2 Line Impedance Stabilization Network EMC TEST SYSTEMS FEBRUARY 1996 REV C PN 399197 MODEL 3810/2 Line Impedance Stabilization Network OPERATION MANUAL USA P.O. Box 80589 Austin, Texas 78708-0589 2205 Kramer Lane, Austin, Texas 78758-4047

More information

Description & Applications Questions & Answers Selection Charts Single Phase Selection Charts Three Phase...

Description & Applications Questions & Answers Selection Charts Single Phase Selection Charts Three Phase... SECTION BUCK-BOOST TRANSFORMERS A simple and economical way to correct offstandard voltages... from 95 to 500 volts; single and three phase, in sizes up to 60 kva. Simplified buck-boost rating charts make

More information

Instructions AVC125-10: Voltage Regulator. Voltage Range. Maximum Continuous Burden. Voltage Range. Nominal Frequency

Instructions AVC125-10: Voltage Regulator. Voltage Range. Maximum Continuous Burden. Voltage Range. Nominal Frequency www.basler.com + 68.654.234 (USA) info@basler.com Model Description AVC25-0 Voltage Regulator INTRODUCTION The AVC63-2 and AVC25-0 regulate the level of excitation supplied to the field of a conventional,

More information

TABLE OF CONTENT

TABLE OF CONTENT Page : 1 of 34 Project Engineering Standard www.klmtechgroup.com KLM Technology #03-12 Block Aronia, Jalan Sri Perkasa 2 Taman Tampoi Utama 81200 Johor Bahru Malaysia TABLE OF CONTENT SCOPE 3 REFERENCES

More information

Liebert Datawave GUIDE SPECIFICATIONS kva Magnetic Synthesizer Power Conditioning System

Liebert Datawave GUIDE SPECIFICATIONS kva Magnetic Synthesizer Power Conditioning System 1.1 SUMMARY DISCONTINUED PRODUCT GUIDE SPECIFICATIONS 15-75 kva Magnetic Synthesizer Power Conditioning System 1.0 GENERAL These specifications describe requirements for a complete power conditioning and

More information

Model 935A Current Source Operation Manual

Model 935A Current Source Operation Manual Model 935A Current Source Operation Manual Arbiter Systems, Inc. Paso Robles, CA 93446 U.S.A. ii Description This manual is issued for reference only, at the convenience of Arbiter Systems. Reasonable

More information

SECTION THREE-PHASE UNINTERRUPTIBLE POWER SYSTEM

SECTION THREE-PHASE UNINTERRUPTIBLE POWER SYSTEM SECTION 263353 - THREE-PHASE UNINTERRUPTIBLE POWER SYSTEM PART 1 GENERAL 1.1 SUMMARY A. This specification defines the electrical and mechanical characteristics and requirements for a continuous-duty three-phase,

More information

LIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING

LIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING LIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING 1.0 General This specification covers the electrical characteristics and general

More information

SE-502 MANUAL GROUND-FAULT GROUND-CONTINUITY DETECTOR

SE-502 MANUAL GROUND-FAULT GROUND-CONTINUITY DETECTOR SE-502 MANUAL GROUND-FAULT GROUND-CONTINUITY DETECTOR March 5, 2002 PRELIMINARY 1 Publication: SE-502-M Document: S95-C502-00000 Printed in Canada. Copyright 2002 by Startco Engineering Ltd. All rights

More information

Distribution/Substation Transformer

Distribution/Substation Transformer Distribution/Substation Transformer Type VFI, Vacuum Fault Interrupter Transformer Option Functional Specification Guide Functional specification for 15 kv, 25 kv, or 35 kv vacuum fault interrupter distribution/substation

More information

ENGINEERING DATA SUBMITTAL For the Interconnection of Generation System

ENGINEERING DATA SUBMITTAL For the Interconnection of Generation System WHO SHOULD FILE THIS SUBMITTAL: Anyone in the final stages of interconnecting a Generation System with Nodak Electric Cooperative, Inc. This submittal shall be completed and provided to Nodak Electric

More information

SHUNT CAPACITOR BANK DESIGN AND PROTECTION BASICS

SHUNT CAPACITOR BANK DESIGN AND PROTECTION BASICS SHUNT CAPACITOR BANK DESIGN AND PROTECTION BASICS Introduction Shunt capacitor units are typically used to deliver capacitive reactive compensation or power factor correction. The use of shunt capacitor

More information

Liebert Datawave. GUIDE SPECIFICATIONS kva Magnetic Synthesizer Power Conditioning System 1.0 GENERAL

Liebert Datawave. GUIDE SPECIFICATIONS kva Magnetic Synthesizer Power Conditioning System 1.0 GENERAL 1.1 SUMMARY GUIDE SPECIFICATIONS 100-200 kva Magnetic Synthesizer Power Conditioning System 1.0 GENERAL These specifications describe requirements for a complete power conditioning and distribution system,

More information

Addendum to Instructions for Installation, Operation and Maintenance of Digitrip 3000 Protective Relays

Addendum to Instructions for Installation, Operation and Maintenance of Digitrip 3000 Protective Relays Dual-Source Power Supply Addendum to I.B. 17555 Addendum to Instructions for Installation, Operation and Maintenance of Digitrip 3000 Protective Relays Table of Contents Page 1.0 Introduction...1 2.0 General

More information

Line to Ground Voltage Monitoring on Ungrounded and Impedance Grounded Power Systems

Line to Ground Voltage Monitoring on Ungrounded and Impedance Grounded Power Systems Line to Ground Voltage Monitoring on Ungrounded and Impedance Grounded Power Systems December 2010/AT301 by Reza Tajali, P.E. Square D Power Systems Engineering Make the most of your energy SM Revision

More information

1

1 Guidelines and Technical Basis Introduction The document, Power Plant and Transmission System Protection Coordination, published by the NERC System Protection and Control Subcommittee (SPCS) provides extensive

More information

American Power Design, Inc.

American Power Design, Inc. FEATURES 4 Customer Selects Output Voltage 4 Outputs to 28 Vdc 4 Wide Input Ranges (10-20Vdc, 18-36Vdc, 20-60Vdc, 36-72Vdc) 4 Excellent Line & Load Regulation 4 Low Output Ripple 4 500 Vdc Output Isolation

More information

SECTION LOW VOLTAGE ACTIVE HARMONIC FILTER SYSTEM NEMA 1 ENCLOSED

SECTION LOW VOLTAGE ACTIVE HARMONIC FILTER SYSTEM NEMA 1 ENCLOSED SECTION 16280 LOW VOLTAGE ACTIVE HARMONIC FILTER SYSTEM NEMA 1 ENCLOSED PART 1 - GENERAL 1.1 SUMMARY This specification defines the requirements for active harmonic filter systems in order to meet IEEE-519-2014

More information

Experimental Investigations and Calculations in 6-35 kv Networks with Various Neutral Conditions

Experimental Investigations and Calculations in 6-35 kv Networks with Various Neutral Conditions PQ20 June 16-18, 2010 Kuressaare Experimental Investigations and Calculations in 6-35 kv Networks with Various Neutral Conditions A. Shirkovets, A. Vasilyeva, A. Telegin LLC BOLID, Novosibirsk, Russia

More information

DP&L s Technical Requirements for Interconnection and Parallel Operation of Distributed Generation

DP&L s Technical Requirements for Interconnection and Parallel Operation of Distributed Generation DP&L s Technical Requirements for Interconnection and Parallel Operation of Distributed Generation Technical Requirements for Interconnection and Parallel Operation of Distributed Generation Single Phase

More information

Current Probes. User Manual

Current Probes. User Manual Current Probes User Manual ETS-Lindgren Inc. reserves the right to make changes to any product described herein in order to improve function, design, or for any other reason. Nothing contained herein shall

More information

American Power Design, Inc.

American Power Design, Inc. FEATURES 4 Customer Selects Output Voltage 4 Outputs to 1000 Vdc 4 Fully Programable Outputs 4 Single and Dual Outputs 4 Wide Input Ranges (10-20Vdc, 18-36Vdc) 4 1000 Vdc Output Isolation 4 Continuous

More information

(2) New Standard IEEE P (3) Core : (4) Windings :

(2) New Standard IEEE P (3) Core : (4) Windings : (d) Electrical characteristics (such as short-circuit withstand, commutating reactance, more number of windings, etc); (e) Longer life expectancy; (f) Energy efficiency; (g) more demanding environment.

More information

Insulation Co-ordination For HVDC Station

Insulation Co-ordination For HVDC Station Insulation Co-ordination For HVDC Station Insulation Co-ordination Definitions As per IEC 60071 Insulation Coordination is defined as selection of dielectric strength of equipment in relation to the operating

More information

American Power Design, Inc.

American Power Design, Inc. FEATURES 4 Customer Selects Output Voltage 4 Outputs to 28 Vdc 4 Wide Input Ranges (10-20Vdc, 18-36Vdc, 20-60Vdc, 36-72Vdc) 4 Excellent Line & Load Regulation 4 500 Vdc Output Isolation 4 Continuous Short

More information

SC1000 DGPS USCG Dual Transmitter

SC1000 DGPS USCG Dual Transmitter Southern Avionics Company's DGPS Reference Station Transmitter System. Model: SC1000 DUAL USCG SC1000 DGPS USCG Dual Transmitter QUALIFICATIONS: Meets applicable requirements of the United States Coast

More information

12604 N New Reflection Dr Marana, AZ, FAX

12604 N New Reflection Dr Marana, AZ, FAX 12604 N New Reflection Dr Marana, AZ, 85658 520 780 9030 206 219 4205 FAX HighVoltage@Highvoltageprobes.com www.highvoltageprobes.com Bare Probe Manual October 21, 2012 1 Safety High Voltage Safety is

More information

American Power Design, Inc.

American Power Design, Inc. FEATURES 4 Customer Selects Output Voltage 4 Outputs to 1000 Vdc 4 Low Profile 4 Single and Dual Outputs 4 Ultra Wide Input Ranges (9-36Vdc, 20-60Vdc, 36-72Vdc) 4 1000 Vdc Output Isolation 4 Continuous

More information

OPERATION & SERVICE MANUAL FOR FC 110 AC POWER SOURCE

OPERATION & SERVICE MANUAL FOR FC 110 AC POWER SOURCE OPERATION & SERVICE MANUAL FOR FC 100 SERIES AC POWER SOURCE FC 110 AC POWER SOURCE VERSION 1.3, April 2001. copyright reserved. DWG No. FC00001 TABLE OF CONTENTS CHAPTER 1 INTRODUCTION... 1 1.1 GENERAL...

More information

Tab 8 Surge Arresters

Tab 8 Surge Arresters s en em Tab 8 Surge Arresters Si Distribution System Engineering Course Unit 10 2017 Industry Inc., All Rights Reserved Surge Arresters The main protective devices against system transient overvoltages.

More information

Type CP-S, CP-C & CP-A Switch mode

Type CP-S, CP-C & CP-A Switch mode Switch mode power CP-S, CP-C & CP-A Switch mode Characteristics CP-S and CP-C range Output current 5 A, 10 A and 20 A Integrated power reserve of up to 50 % 5 A and 10 A devices with pluggable connecting

More information

SYNCHRONISING AND VOLTAGE SELECTION

SYNCHRONISING AND VOLTAGE SELECTION SYNCHRONISING AND VOLTAGE SELECTION This document is for Relevant Electrical Standards document only. Disclaimer NGG and NGET or their agents, servants or contractors do not accept any liability for any

More information

LCM100 USER GUIDE. Line Carrier Modem INDUSTRIAL DATA COMMUNICATIONS

LCM100 USER GUIDE. Line Carrier Modem INDUSTRIAL DATA COMMUNICATIONS USER GUIDE INDUSTRIAL DATA COMMUNICATIONS LCM100 Line Carrier Modem It is essential that all instructions contained in the User Guide are followed precisely to ensure proper operation of equipment. Product

More information

Managing the Health and Safety of Li-Ion Batteries using a Battery Electronics Unit (BEU) for Space Missions

Managing the Health and Safety of Li-Ion Batteries using a Battery Electronics Unit (BEU) for Space Missions NASA Battery Power Workshop 11/27/07 11/29/07 Managing the Health and Safety of Li-Ion Batteries using a Battery Electronics Unit (BEU) for Space Missions George Altemose Aeroflex Plainview, Inc. www.aeroflex.com/beu

More information

INSTRUMENTS, INC. Model 2960AX Disciplined Quartz Frequency Standard 2960AX. Section Page Contents

INSTRUMENTS, INC. Model 2960AX Disciplined Quartz Frequency Standard 2960AX. Section Page Contents INSTRUMENTS, INC. Model 2960AX Disciplined Quartz Frequency Standard 2960AX Section Page Contents 1.0............................. 2......................... Description 2.0.............................

More information

INTERIM ARRANGEMENTS FOR GRID TIED DISTRIBUTED ENERGY RESOURCES. Technical Requirements for Grid-Tied DERs

INTERIM ARRANGEMENTS FOR GRID TIED DISTRIBUTED ENERGY RESOURCES. Technical Requirements for Grid-Tied DERs INTERIM ARRANGEMENTS FOR GRID TIED DISTRIBUTED ENERGY RESOURCES Technical Requirements for Grid-Tied DERs Projects Division 6/29/2017 Contents 1 Definitions and Acronyms... 1 2 Technical Interconnection

More information

INSTRUCTION MANUAL MODEL 2455T SUBCARRIER MODULATOR

INSTRUCTION MANUAL MODEL 2455T SUBCARRIER MODULATOR INSTRUCTION MANUAL MODEL 2455T SUBCARRIER MODULATOR Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., and may not be reproduced or duplicated in any form

More information

SSR-150xxx-40VL-12P-xC-xxxCS

SSR-150xxx-40VL-12P-xC-xxxCS HELLROARING TECHNOLOGIES, INC. P.O. BOX 1521 POLSON, MT 59860 406 883-3801 HTTP://WWW.HELLROARING.COM SUPPORT@HELLROARING.COM SSR-150xxx-40VL-12P-xC-xxxCS The SSR-150xxx-40VL-12P-xC-xxxCS is designed for

More information

Sequence Networks p. 26 Sequence Network Connections and Voltages p. 27 Network Connections for Fault and General Unbalances p. 28 Sequence Network

Sequence Networks p. 26 Sequence Network Connections and Voltages p. 27 Network Connections for Fault and General Unbalances p. 28 Sequence Network Preface p. iii Introduction and General Philosophies p. 1 Introduction p. 1 Classification of Relays p. 1 Analog/Digital/Numerical p. 2 Protective Relaying Systems and Their Design p. 2 Design Criteria

More information

SECTION AUTOMATIC TRANSFER SWITCH

SECTION AUTOMATIC TRANSFER SWITCH SECTION 26 36 23 PART 1 - GENERAL 1.1 THE REQUIREMENT A. Furnish and install automatic transfer switches (ATS) with number of poles, amperage, voltage, withstand and close-on ratings as shown on the plans.

More information

American Power Design, Inc.

American Power Design, Inc. , Inc. FEATURES 4 Customer Selects Output Voltage 4 Ultra Wide Input Ranges (936Vdc, 2060Vdc) 4 Efficiency 89% (typ.) 4 Independently Isolated Outputs 4 SixSided Shielded Case 4 Remote On/Off Control 4

More information

THE PROBE, 5 METER, 2WIRE, LOOP POWERED SINGLE POINT LEVEL MEASUREMENT SYSTEM (ULTRASONIC)

THE PROBE, 5 METER, 2WIRE, LOOP POWERED SINGLE POINT LEVEL MEASUREMENT SYSTEM (ULTRASONIC) THE PROBE, 5 METER, 2WIRE, LOOP POWERED SINGLE POINT LEVEL MEASUREMENT SYSTEM (ULTRASONIC) Part 1. General 1.1 Scope A. This section describes the requirements for an ultrasonic, single-point level controller

More information

Technical Equipment Specification

Technical Equipment Specification STATE OF CALIFORNIA Office of the State Chief Information Officer Public Safety Communications Division Technical Equipment Specification Equipment Type: Transmitter/Receiver Mobile Relay/Base/Control

More information

Model 3210C. 100 Ampere AC Current Standard. Operating Manual

Model 3210C. 100 Ampere AC Current Standard. Operating Manual Model 3210C 100 Ampere AC Current Standard Operating Manual This page intentionally left blank. 3210C OPERATORS MANUAL Serial No. Win-man\3210C.wpd This page intentionally left blank. 3210C OPERATORS MANUAL

More information

WAVEFORM CORRECTOR (WAVEFORM CORRECTORS) REPLACES SURGE PROTECTION DEVICES (SPD) PREVIOUSLY KNOWN AS (TVSS)

WAVEFORM CORRECTOR (WAVEFORM CORRECTORS) REPLACES SURGE PROTECTION DEVICES (SPD) PREVIOUSLY KNOWN AS (TVSS) WAVEFORM CORRECTOR (WAVEFORM CORRECTORS) REPLACES SURGE PROTECTION DEVICES (SPD) PREVIOUSLY KNOWN AS (TVSS) 1 PART 1: GENERAL This section describes materials and installation requirements for low voltage

More information

SSR VL-12P-xC-NCS

SSR VL-12P-xC-NCS HELLROARING TECHNOLOGIES, INC. P.O. BOX 1521 POLSON, MT 59860 406 883-3801 HTTP://WWW.HELLROARING.COM SUPPORT@HELLROARING.COM SSR-40150-200VL-12P-xC-NCS The SSR-40150-200VL-12P-xC-NCS is designed for Low

More information

General Application Notes Remote Sense Remote On / Off Output Trim Series Operation Parallel Operation...

General Application Notes Remote Sense Remote On / Off Output Trim Series Operation Parallel Operation... General... 28 Remote Sense... 29 Remote On / Off... 30 Output Trim... 30 Series Operation... 32 Parallel Operation... 33 Synchronization... 33 Power Good Signal... 34 Electro Magnetic Filter (EMI)... 34

More information

Angular Rate Sensor. Owner's Manual

Angular Rate Sensor. Owner's Manual Angular Rate Sensor Owner's Manual Part Number: ARS-C132-1A WATSON INDUSTRIES, INC. 3041 MELBY ROAD EAU CLAIRE, WI 54703 Phone: (715) 839-0628 FAX: (715) 839-8248 email: support@watson-gyro.com 1 Table

More information

E S C R I P T I V E B U L L E T I N .,.,.,. Bulletin DB-106. October, Square D Company Power System Studies ---1 I SQU ARED COMPANY --

E S C R I P T I V E B U L L E T I N .,.,.,. Bulletin DB-106. October, Square D Company Power System Studies ---1 I SQU ARED COMPANY -- D.,.,.,. E S C R I P T I V E B U L L E T I N Bulletin DB-106 Square D Company October, 1990 ---1 I SQU ARED COMPANY -- Electrical Power Distribution System - The Heart of the Business From small commercial

More information

Coil Products Beginnings 1960 State of the Art. Customer partnership around the globe. Continuous innovation since 1900

Coil Products Beginnings 1960 State of the Art. Customer partnership around the globe. Continuous innovation since 1900 Coil Products Coil Products Customer partnership around the globe More than 250,000 coil products delivered to more than 170 countries. More than 60 years of operational experience. 35,000 in Europe 13,000

More information

State of North Dakota Engineering data submittal Page 1 For interconnection of distributed generation to Otter Tail Power Company

State of North Dakota Engineering data submittal Page 1 For interconnection of distributed generation to Otter Tail Power Company Engineering data submittal Page 1 WHO SHOULD FILE THIS SUBMITTAL : Anyone in the final stages of in terconnecting a Generation System with Otter Tail Power. This submittal shall be completed and provided

More information

Product Data Sheet. Models 1022/1025/1029C/1032/3629B 3629B. Models 1022/1025/1032. Model 1029C. Model 3629B. Phase Angle Power Control

Product Data Sheet. Models 1022/1025/1029C/1032/3629B 3629B. Models 1022/1025/1032. Model 1029C. Model 3629B. Phase Angle Power Control s 1022/1025/1029C/1032/3629B 3629B Product Data Sheet s 1022/1025/1032 Single phase power controllers Current ratings from 10 to 70 Amps 1022-0 to 5VDC or pot input 1025-4 to 20 ma signal 1032 Current

More information

305 Stimulus Isolator. Description

305 Stimulus Isolator. Description Description The Model 305 Stimulus Isolator utilizes photon coupling to provide nearly ideal isolation of the pulse and train outputs of the WPI Series 300 Anapulse Stimulators. Two Model 305 units are

More information

Voltage Probe Manual and Data North Star High Voltage, Inc. Rev January 2016

Voltage Probe Manual and Data North Star High Voltage, Inc. Rev January 2016 561 Rose Loop NE Bainbridge Island, WA, USA 9811 (52)78-93; (26)219-425 FAX http://www.highvoltageprobes.com probes@highvoltageprobes.com Voltage Probe Manual and Data North Star High Voltage, Inc. Rev

More information