FAS 10 mm PICOSOL Direct acting solenoid valve

Transcription

1 FS 0 mm PICOSOL > > /, /; Manifold mounting > > Long life 00 million cycles > > Compact Design > > Low power consumption Technical features Medium: ir, oxygen, neutral gases (0 %... 9 % humidity, non condensing), 0 μm filtered Operation: Direct acting -way and -way valves, normally closed and normally opened Operating pressure: bar (0... psi) Details on page Flow: l/min at bar (9 psi) at +0 C (+68 F) Mounting: Manifold Orifice: 0,6... mm Response time: 0... ms Response time measured according to ISO 8 Life expectancy: 00 Mio. cycles for W valves Weight: 0, g (0.0 lbs) mbient/media temperature: C ( F) ir supply must be dry enough to avoid ice formation at temperatures below + C (+ F). Materials: Body: PPS Seat seals: FPM, NBR, EPDM Internal parts: Stainless steel, P Electrical details Voltage: V d.c. Rating: 00 % E.D. Voltage tolerance ± 0% Power consumption: [W] (/0, W)* Electrical insulation 000 V a.c. Protection class IP Insulation class F ( C) * with optional PWM control Following options on request Operating pressure (vacuum) Medium temperature mbient temperature Response time Power consumption Materials Coils Protection class Degreased for oxygen use Manual override Embedded electronics options Integrated pulse width modulation (PWM) Enhanced opening time repeatability Larger input voltage tolerances Improved boosting by plunger movement detection Improved boosting by plunger movement detection wi h power adaptation Faster valve closing Current control for improved performances over temperature range Reverse polarity protection Led signalization Pulse width modulation (PWM) control PWM can be used to control the valve and should be set as follows: Definition Value to be applied Hit voltage Voltage used for he valve to commute Valve nominal voltage Holding voltage Voltage applied to he valve after commutation Set duty cycle to guarantee specified holding voltage. 0% of nominal voltage can be used if no value specified. Hit time Maximum time required to ensure full valve commutation 0 ms at T > 0 C *) PWM frequency khz *) Please contact us for application outside of those conditions. notice, the specifications given in this document. (006-07d) 0 Fluid utomation Systems s.a. / en..00.0

2 FS 0 mm PICOSOL Technical data - standard models Symbol Operation Orifice 0 / NO (/ mounting pattern) 0 / NC (/ mounting pattern) / NC / NC / NO / UNI *) Cv = 0,07 kv *) Power consumption: boosting power during ca. 0 ms / holding power *) Push only Operating pressure kv*) Power consumption Voltage Manual override Seal material Drawing Model (mm) (bar) (psi) (l/min) (W) *) (V d.c.) *) no. 0, , With FPM -PI060H++YV, , With FPM -PI0H++YR 0, , With FPM -PI060H++YV 0, ,9 With FPM -PI0-H++YV, 0,..., , With FPM -PI0H++YV 0, , Without FPM -P60-H++YV, ,9 Without FPM -P60-H++YR, , /0, Without FPM -P60-H+6+X 0, , With FPM -PI060H++YV 0, ,9 With FPM -PI0-H++YV, ,7 /0, With FPM -PI0H+6+ZR,... 6, , /0, With FPM -PI0H+6+ZR 0, ,9 With FPM -PI0-H++YV 0, ,8 With FPM -PI0-H++YV ccessories Electrical connection Mounting plate with barbed fittings for mm ØID tubing (up to bar) Mounting manifold with M threads position Mounting manifold with threads... 8 positions Electrical connector Molex with 00 mm flying leads Page Page Page S.77 S0.77 vailable on request Page S0.0 en notice, the specifications given in this document. (006-07d) 0 Fluid utomation Systems s.a. /

3 FS 0 mm PICOSOL Dimensions 6,, 7 8, 0, 6,,6,,7 M,9,9 8,, 6,, 0 6, 8,, 6,8,,7,7,7 0, M,6 0,8,,6 Manual override, push only Sealing area The recommended mounting screw tightening torque is 0, Nm. Connector mates with Molex ll solenoids are supplied with mounting screws and gasket. / notice, the specifications given in this document. (006-07d) 0 Fluid utomation Systems s.a. en..00.0

4 FS 0 mm PICOSOL Mounting plate with barbed fittings for mm ØID tubing (up to bar) Model: S.77 Mounting manifold Model: S0.77, 9, 6, 7 R,6 0, 6, 0,, 7, 9, 0, 0 ø,6 ø,8 Mounting thread M x deep Mounting manifold Model: on request, 0 6 0, ±0, 8 (N-) x 0, X Y 0, 6 0, ±0, (N-) x 0, Mounting thread M x, deep Valve station X Y 6,, 7 7,, 8 6 8, 6, , 8, en notice, the specifications given in this document. (006-07d) 0 Fluid utomation Systems s.a. /

5 FS 0 mm PICOSOL Electrical connector Model: S0.0,, Warning These products are intended for use in air, oxygen and neutral gas systems only. Do not use these products where pressures and temperatures can exceed those listed under»technical features«. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult IMI FS. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. / notice, the specifications given in this document. (006-07d) 0 Fluid utomation Systems s.a. en..00.0