MULTI POWER TRANSDUCER MODEL LSMT4

Transcription

1 ISTRUCTIO MAUAL MULTI POWER TRASDUCER MODEL LSMT4 BEFORE USE... Thank you for choosing M-System. Before use, please check contents of the package you received as outlined below. If you have any problems or questions with the product, please contact M-System s Sales Office or representatives. PACKAGE ICLUDES: Multi Power Transducer... (1) Output label for users... (2) Mounting slider... (2) MODEL O. Confirm that the model number described on the product is exactly what you ordered. ISTRUCTIO MAUAL This manual describes necessary points of caution when you use this product, including installation, connection and basic maintenance procedures. POITS OF CAUTIO COFORMITY WITH EU DIRECTIVES This equipment is suitable for Pollution Degree 2 and Measurement Category II, Installation Category II. Prior to installation, check that the insulation class of this unit satisfies the system requirements. Insulation class of this unit is as follows. Input to output Reinforced insulation (480 V) Output to auxiliary power Reinforced insulation (300 V) Altitude up to 2000 meters. The equipment must be mounted inside a panel. The equipment must be installed such that appropriate clearance and creepage distances are maintained to conform to CE requirements. Failure to observe these requirements may invalidate the CE conformance. The actual installation environments such as panel configurations, connected devices, connected wires, may affect the protection level of this unit when it is integrated in a panel system. The user may have to review the CE requirements in regard to the whole system and employ additional protective measures to ensure the CE conformity. Install lightning surge protectors for those wires connected to remote locations. GEERAL PRECAUTIO Before you remove or mount the unit, turn off the power supply and the input signal for safety. EVIROMET Indoor use. Do not install the unit where it is directly exposed to rain, water droplets or sunlight. When heavy dust or metal particles are present in the air, install the unit inside proper housing and ventilate it. Do not install the unit where it is subjected to continuous vibration. Do not apply physical impact to the unit. Environmental temperature must be within -10 to +55 C (14 to 131 F) with relative humidity within 30 to 90% RH in order to ensure adequate life span and operation. WIRIG Do not install cables close to noise s (relay drive cable, high frequency line, etc.). Do not bind these cables together with those in which noises are present. Do not install them in the same duct. AD... The unit is designed to function as soon as power is supplied, however, a warm up for 10 minutes is required for satisfying complete performance described in the data sheet. LIGHTIG SURGE PROTECTIO In order to protect the unit from lightning surges entering through signal and power supply cables, use of appropriate lightning surge protectors are recommended. Please contact M-System. AUXILIARY POWER IPUT RATIGS Power input ratings are specified by the model number suffix code V AC rating: V AC, 50/60 Hz, <20VA V DC rating: V DC, <9W 24V DC rating: 24V±10%, <9W 48V DC rating: 48V±10%, <9W EM-1957 Rev.3 P. 1 / 14

2 COMPOET IDETIFICATIO FROT PAEL COFIGURATIO Output Terminals DATA Display Configuration Jack Power Input Terminals Control Buttons Input Terminals ISTALLATIO WALL MOUTIG Insert the provided slider into upper side of the unit, and pull out the slider on the lower side. Fasten the M4 screw to the hole (4.5 mm dia.) of the slider. (torque 1.4 m) To remove the slider, pull it out while pushing the latch to inside as shown in the figure below. DI RAIL MOUTIG Set the unit so that its DI rail adaptor is at the bottom. Position the upper hook at the rear side of the unit on the DI rail and push in the lower. When removing the unit, push down the DI rail adaptor utilizing a minus screwdriver and pull. DI Rail 35mm wide push push Slider EM-1957 Rev.3 P. 2 / 14

3 TERMIAL COECTIOS Connect the unit as in the diagram below. EXTERAL DIMESIOS unit: mm (inch) 7.2 (.28) 24 M3.5 TERMIAL SCREW (.17) DIA. MTG HOLE TERMIAL COVER 140 (5.52) 126 (4.96) 115 (4.53) 119 (4.69) (DI rail mounting) DI RAIL 35mm wide 75 (2.95) 125 (4.92) 116 (4.57) 6.5 (.26) [3.3 (.13)] 8.6 (.34) 13 M4 TERMIAL SCREW MOUTIG REQUIREMETS unit: mm (inch) 75 (2.95) 4-M4 126 (4.96) 130 (5.12) min. EM-1957 Rev.3 P. 3 / 14

4 WIRIG ISTRUCTIOS SOLDERLESS TERMIAL mm (inch) Refer to the drawing below for recommended ring tongue terminal size. Spade tongue type is also applicable. M3.5 Screw (output) Torqu: 0.6 m Applicable wire size: mm 2 (.2 ) max 3. (.1 ) max M4 Screw (auxiliary power, voltage input and current input) Torqu: 1.4 m Applicable wire size: mm 2 4 (.16) max. 8 max. (.31) 4.3 (.17) dia. TERMIAL COECTIOS ote: In order to improve EMC performance, bond the FE terminal to ground. Caution: FE terminal is OT a protective conductor terminal. TERMIAL ASSIGMET ELECTRICAL COECTIO Output Terminals Power Input Terminals Input Terminals CH1+ CH1 CH10+ CH10 CH11+ CH11 CH12+ CH12 U(+) V( ) FE AALOG OUTPUT AALOG OUTPUT 10 COTACT OUTPUT 1 COTACT OUTPUT 2 POWER JACK COFIGURATOR EM-1957 Rev.3 P. 4 / 14

5 System / Application Terminal System / Application Terminal P1 1S 1L P1 1S 1L P1 P2 P3 1S 1L 3S 3L P1 P2 P3 1S 1L 3S 3L Single phase / 2-wire P1 1S 1L k K l L 3-phase / 3-wire, unbalanced P1 P2 P3 1S 1L 3S 3L k l k l u v u v v u U V k K l L U V V U k l k l P1 P2 P3 1S 1L P1 P2 P3 1S 1L P1 1S 1L P1 1S 1L 3-phase / 3-wire, balanced P1 P2 P3 1S 1L k K l L 3-phase / 4-wire, balanced P1 1S 1L k K l L u v v u u v k l U V k K l L P1 P3 1S 1L 3S 3L P1 P3 1S 1L 3S 3L Single phase / 3-wire P1 P3 1S 1L 3S 3L k K l L k K l L P1 P2 P3 1S 1L 2S 2L 3S 3L u v v u U V V U k l k l 3-phase / 4-wire, unbalanced P1 P2 P3 1S 1L 2S 2L 3S 3L k l k l k l P1 P2 P3 1S 1L 2S 2L 3S 3L u v u v u v U V U V U V k l k l k l EM-1957 Rev.3 P. 5 / 14

6 OPERATIG MODE The measurement display items can be chosen with 4 buttons. Phase voltage, Phase 1 Active power Power factor 1THD Phase voltage, Phase 2 Reactive power Frequency 2THD Phase voltage, Phase 3 Apparent power Power factor, Phase 1 3THD Phase to phase, 1 2 Active power, Phase 1 Power factor, Phase 2 Phase to phase THD, 1 2 Phase to phase, 2 3 Active power, Phase 2 Power factor, Phase 3 Phase to phase THD, 2 3 Phase to phase, 3 1 Active power, Phase 3 Phase to phase THD, 3 1 Current, Line 1 Reactive power, Phase 1 Current THD, Line 1 Current, Line 2 Reactive power, Phase 2 Current THD, Line 2 Current, Line 3 Reactive power, Phase 3 Current THD, Line 3 eutral current Apparent power, Phase 1 eutral current THD Apparent power, Phase 2 Apparent power, Phase 3 CHARACTER SET A B C D E F G H I J M O P Q R S T U V W X Y Z EM-1957 Rev.3 P. 6 / 14

7 SETTIG MODE BUTTO OPERATIO Button Menu/ umeric Input IU / PQS Move between Menu/ Increment/decrement at selected digit Select Menu/ Escape from Menu/ Enter the value Return without entering the value SETTIG MEU/SETTIG GROUP MEU Flow chart Operating Mode Press and hold Incorrect Passcode Incorrect Passcode Enter Passcode Enter the passcode. Passcode range: 0000 to When entered passcode is correct, the unit enters to setting menu. When entered passcode is incorrect, the unit returns to operating mode with error message. Setting Menu DEV.I Version Each time is pressed, the firmware version and the model number are alternately displayed. REBT Reboot O YES Operation Return to Setting Menu Reboot the unit PASS Change passcode The passcode can be changed within 0000 to Factory default is LOOP Loop test By selecting output item of loop test; output selection can be changed. AO1 AO10 PO1 PO2 Output Analog output 1 Analog output 10 Pulse output 1 Pulse output 2 Loop test operation Select the digit in the engineering unit value Increase the value at selected digit Decrease the value at selected digit Select O/OFF with / SETT Setting Group Menu IP To Input Setting Menu EER To Pulse Output Setting Menu AOUT To Analog Output Setting Menu OPT To Option Setting Menu MTE To Maintenance Menu EM-1957 Rev.3 P. 7 / 14

8 IP IPUT SETTIG MEU Flow chart To Setting Group Menu Input Setting Menu SYS System Configuration Operation 1P2W : Single phase/2-wire 1P3W : Single phase/3-wire 3P3B : 3-phase/3-wire balanced 3P3U : 3-phase/3-wire unbalanced 3P4B : 3-phase/4-wire balanced * 1 3P4U : 3-phase/4-wire unbalanced * 1 *1. Available only with LSMT4-2xxx-x CT1 CT rating, primary 1 to A [5A] CT2 CT rating, secondary 1 to 5 A [5A] VT1 VT rating, primary 0.05 to kv [0.11 kv] * 2 VT2 VT rating, secondary 50 to 480 V [110 V] * 2 When this setting is changed, voltage range is automatically set as shown in table below. Setting Others Automatic voltage range Same as the setting value VRG Voltage range 50 to 480 (V) [150 V] FREQ AC frequency Operation U1 : Voltage 1 (*) I1 : Current 1 CO I Low-end cutout, current 0.0 to 99.9 (%) [1.0 %] The current value below ( rated current setting value ) is regarded as 0 A. (*): Factory default setting CO V Low-end cutout, voltage 0.0 to 99.9 (%) [1.0 %] The voltage value below ( rated voltage setting value ) is regarded as 0 V. *2. Set rated voltage for VT according to the table shown below. System Configuration Voltage Single phase/2-wire Voltage between V V 3-phase/3-wire Line-to-line voltage V Single phase/3-wire Voltage between V V 3-phase/4-wire Phase voltage V EM-1957 Rev.3 P. 8 / 14

9 ETER PULSE OUTPUT SETTIG MEU Flow chart To Setting Group Menu Select Output PO1 PO2 Pulse Output Setting Menu CT Energy count type ID PARAMETER EP Active energy, incoming EQ Reactive energy, LAG ES Apparent energy EP Active energy, outgoing EQ Reactive energy, LEAD EQ G Reactive energy, incoming, LAG EQ D Reactive energy, incoming, LEAD EQ G Reactive energy, outgoing, LAG EQ D Reactive energy, outgoing, LEAD EQ P Reactive energy, incoming EQ P Reactive energy, outgoing WEI Pulse weight ID PARAMETER 0.001(*) p kwh/pulse 0.01 p 0.01 kwh/pulse 0.1 p 0.1 kwh/pulse 1.0 p 1.0 kwh/pulse p is determined by n calculated from the formula shown below and the table shown below. n= a primary rated voltage primary rated current 1000 Where a is 1: Single phase/2-wire, 2: Single phase/3-wire, 3: 3-phase, 3: 3-phase/4-wire. n p < n < n < n < n < DUR Pulse width Selectable within 100 to 2000 msec. by 100 msec. steps. [100 msec.] EM-1957 Rev.3 P. 9 / 14

10 AOUT AALOG OUTPUT SETTIG MEU Flow chart To Setting Group Menu Select Output AO1 AO2 AO3 Analog Output Setting Menu IP Assigned measurand Refer to the table, Parameters to be assigned to analog outputs. AO4 AO5 AO6 AO7 AO8 AO9 AO10 SCAL Proportional output Set the parameters for four items shown below. Setting range ISP Input range Refer to Analog output parameters table IZER Input 0 % Refer to Analog output parameters table OSP Output 100 % Refer to Analog output range table OZER Output 0 % Refer to Analog output range table With Proportional output, the input range (Input 0 % to Input range) is converted to output range (Output 0 % to Output 100 %.) After Input range is specified, Input 0 % is automatically assigned. Refer to the table, Parameters to be assigned to analog outputs for the value automatically assigned. LIA Linearization SCAL (*) TBL Set 0 % and 100 % for input and output to convert with Proportional output. Refer to the Proportional output for settings. Set the linearization table to convert with the linearization table. Refer to the linearization table for settings. TBL Linearization table Set input/output of 10 points in the linearization table as shown below. Setting range I0 Input 1st point Refer to the Analog : : output range I9 Input 10th point OUT0 Output 1st point Refer to the Analog : : output range OUT9 Output 10th point ADJ Adjustment By selecting item in the table below, output adjustment is performed in the adjustable range. ZERO SPA Adjustable range to (%) [0.00 %] to (%) [ %] Analog output range Model number Output rating Available setting range LSMT4-xxAx-x 4.00 to (ma) 3.20 to (ma) LSMT4-xx4x-x to (V) to (V) LSMT4-xx5x-x to (V) to (V) LSMT4-xx6x-x to (V) to (V) EM-1957 Rev.3 P. 10 / 14

11 Analog output parameters OE I1 I2 I3 I U12 U23 U31 U1 U2 U3 P P1 P2 P3 Q Q1 Q2 Q3 S S1 S2 S3 PF PF1 PF2 PF3 F ot assigned Current, Line 1 Current, Line 2 Current, Line 3 eutral current Phase to phase, Line 1 2 Phase to phase, Line 2 3 Phase to phase, Line 3 1 Phase voltage, Phase 1 Phase voltage, Phase 2 Phase voltage, Phase 3 Active power Active power, Phase 1 Active power, Phase 2 Active power, Phase 3 Reactive power Reactive power, Phase 1 Reactive power, Phase 2 Reactive power, Phase 3 Apparent power Apparent power, Phase 1 Apparent power, Phase 2 Apparent power, Phase 3 Power factor Power factor, Phase 1 Power factor, Phase 2 Power factor, Phase 3 Frequency Input range -100% -75% -50% -25% 0% 25% 50% 75% 100% 0 CT secondary rating 0 Voltage range P (outgoing) 0 (incoming) P P (LEAD) 0 (LAG) P 0 P 0 (LEAD) 1 (LAG) Available setting range for input range 0.00 to % [0.00 to %] 0.00 to % [0.00 to %] to % [0.00 to %] to % [ to %] 0.00 to % [0.00 to %] to % [ to 50.00%] 0.00 to % [0.00 to %] Auto setting value for input 0 % Sign inversion value of the input range 0.00 Sign inversion value of the input range T Q Reactive power for bidirectional current P (LEAD) (outgoing) 0 (LAG) P P (LEAD) (incoming) 0 (LAG) P to % [ to %] Sign inversion value of the input range When LEAD/LAG range of power rating is set, the unit outputs 0 to 50 % for outgoing and outputs; 50 to 100 % for incoming. T PF Power factor for bidirectional current 0 (LEAD) (outgoing) 1 (LAG) (incoming) 0 (LEAD) 1 (LAG) P to % [ to 50.00%] Sign inversion value of the input range When LEAD/LAG range of power factor is set, the unit outputs 0 to 50 % for outgoing; 50 to 100 % for incoming. Calculation of P (power rating) P (power rating) is automatically determined by rounding to the unit (CT secondary rating 100 (W)) after calculated with following formula by system configuration and secondary rating of CT/VT. It is available not to round with option setting. Power rating = (CT secondary rating) (VT secondary rating) a Calculation example System configuration a Rating Power rating Single phase/2-wire 1 110V/5A 220V/5A 500W 1000W Single phase/3-wire 3-phase/3-wire V/5A 110V/5A 220V/5A 1000W 1000W 2000W 3-phase/4-wire 3 220V/5A 3500W Inversion of output 0 % to 100 % When negative value is set to input range, output is inverted. For example, % is set to input range of reactive power, % is automatically set to input 0 % and then output characteristic is the figure shown below. Output (ma) Input (var) (LAG) (LEAD) EM-1957 Rev.3 P. 11 / 14

12 OUTPUT EXAMPLES Reactive power for bidirectional current Output (ma) Input (var) 1000 (LEAD) (LAG) (LEAD) (LAG) Outgoing Incoming Power factor for bidirectional current Range-100 to 100% Range-50 to 50% Output (ma) Output (ma) (LEAD) (LAG) (LEAD) (LAG) input (LEAD) (LAG) (LEAD) (LAG) Outgoing Incoming Outgoing Incoming input EM-1957 Rev.3 P. 12 / 14

13 OPT OPTIO SETTIG MEU Flow chart Option Setting Menu To Setting Group Menu ALIM Analog limit Select O/OFF of Analog limit. O Limit at -1 % and +101 % OFF (*) o limit (output -5 to +105 %) RPR Power rating round O (*) OFF After power rating is calculated by the formula below, it is rounded to nearest the integral multiple of (secondary rating 100 (W)). Power rating is calculated by the formula below (not rounded) Power rating = VT secondary rating CT secondary rating a System a configuration Single phase/2-wire Single phase/3-wire 3-phase/3-wire 3-phase/4-wire O OFF PF S Power factor sign IEC (*) Active power is incoming: positive, outgoing: negative IEEE Phase direction is LAG: positive, LEAD: negative Q S Reactive power sign IEC (*) SPC The range from power factor 1.0 to -180 is positive, other is negative. When incoming same as IEC. When outgoing, sign reversed. Q C Reactive power calculation VEC (*) SIGM Vector calculation method: Qn= Sn 2 Pn 2 Reactive power meter method: 1 smp Qn= (Uni ni) Ii + (smp/4) smp i=1 (*): Factory default setting S C Apparent power calculation VEC (*) SUM Vector calculation method: S = P 2 + Q 2 Sum calculation: S = S1 + S2 + S3 EM-1957 Rev.3 P. 13 / 14

14 MTE MAITEACE MEU Flow chart Maintenance Menu To Setting Group Menu BKUP Backup setting O YES Return to Maintenance Menu. Backup present settings into internal memory. REST Restore setting O YES Return to Maintenance Menu. Restore settings in the internal memory. CLR.A Initialization O YES Return to Maintenance Menu. Initialize settings with default. EM-1957 Rev.3 P. 14 / 14