AP1117. General Description. Features. Applications. Typical Application Circuit. Note: R 1A LOW DROPOUT POSITIVE ADJUSTABLE OR FIXED-MODE REGULATOR

Transcription

1 AP7 Features General Description.4V Maximum Dropout at Full Load Current Fast Transient Response Output Current Limiting Built-in Thermal Shutdown Good Noise Rejection 3-Terminal Adjustable or Fixed.5V,.8V,.5V, 3.3V, 5.V Lead Free Packages: SOT3-3L, TO5-3L, SOT89-3L, TO63-3L and TO-3L SOT3-3L, TO5-3L and SOT89-3L: Available in Green Molding Compound (No Br, Sb) Lead Free Finish/RoHS Compliant (Note ) AP7 is a low dropout positive adjustable or fixed-mode regulator with A output current capability. The product is voltage specifically designed to provide well-regulated supply for low IC applications such as high-speed bus termination and low current 3.3V logic supply. AP7 is also well suited for other applications such as VGA cards. AP7 is guaranteed to have lower than.4v dropout at full load current making it ideal to provide well-regulated outputs of.5 to 5. with 6.4V to 8V input supply. AP7 is available in commercial temperature grade. Applications PC Peripheral Communication Typical Application Circuit 5V C uf 5V C uf VIN VIN VOUT GND C uf 3.3V/A VOUT Adj R Ω R Ω V o C uf.5v/a Tab is VOUT Tab is VOUT ( 5V/3.3V fixed output ) ( 5V/.5V ADJ output ) Note: Vo = VREF (+ R R ) AP7 Rev. 6 of MARCH 9

2 AP7 Ordering Information A P 7 X XX X - X Package Vout D : TO5-3L Blank : Adj E : SOT3-3L 5 :.5V K : TO63-3L 8 :.8V T : TO-3L 5 :.5V Y : SOT89-3L 33 : 3.3V 5 : 5.V Lead Free L : Lead Free (Note ) G : Green Packing U : Tube 3 : Tape & Reel Device Tube 3 Tape and Reel Package Packaging Part Number Part Number Code (Note 3) Quantity Quantity Suffix Suffix AP7DXXL-U D TO5-3L 8 -U NA NA AP7DXXL-3 D TO5-3L NA NA 5/Tape & Reel -3 AP7DXXG-U D TO5-3L 8 -U NA NA AP7DXXG-3 D TO5-3L NA NA 5/Tape & Reel -3 AP7EXXL-U E SOT3-3L 75 -U NA NA AP7EXXL-3 E SOT3-3L NA NA 5/Tape & Reel -3 AP7EXXG-U E SOT3-3L 75 -U NA NA AP7EXXG-3 E SOT3-3L NA NA 5/Tape & Reel -3 AP7KXXL-U K TO63-3L 5 -U NA NA AP7KXXL-3 K TO63-3L NA NA 8/Tape & Reel -3 AP7TXXL-U T TO-3L 5 -U NA NA AP7YXXL-3 Y SOT89-3L NA NA 5/Tape & Reel -3 AP7YXXG-3 Y SOT89-3L NA NA 5/Tape & Reel -3 Notes:. TO63-3L and TO-3L are available in Lead Free products only.. EU Directive /95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at 3. Pad layout as shown on Diodes Inc. suggested pad layout document AP, which can be found on our website at AP7 Rev. 6 of MARCH 9

3 AP7 Pin Assignments () SOT89-3L () SOT3-3L 3 VIN VOUT Adj (GND) Tab is VOUT 3 Tab is VOUT VIN VOUT Adj (GND) (3) TO-3L (4) TO5-3L and TO63-3L ( Front View ) 3 VIN 3 VIN VOUT Adj (GND) VOUT Adj (GND) Tab is VOUT Tab is VOUT Pin Descriptions Pin Name I/O PIN # Description Adj (GND) I V OUT O V IN I 3 A resistor divider from this pin to the V OUT pin and ground sets the output voltage (Ground only for Fixed-Mode). The output of the regulator. A minimum of uf capacitor (.5Ω ESR Ω) must be connected from this pin to ground to insure stability. The input pin of regulator. Typically a large storage capacitor is connected from this pin to ground to insure that the input voltage does not sag below the minimum dropout voltage during the load transient response. This pin must always be.3v higher than V OUT in order for the device to regulate properly. AP7 Rev. 6 3 of MARCH 9

4 AP7 Block Diagram V IN 3 V OUT CURRENT LIMIT +.5V + GND (FIXED) Thermal Shutdown - Adj Absolute Maximum Ratings Symbol Parameter Rating Unit V IN DC Supply Voltage -.3 to 8 V T MJ Maximum Junction Temperature 5 o C P D Power Dissipation SOT89-3L SOT3-3L TO-3L TO5-3L TO63-3L Internally limited by maximum junction temperature of 5 o C (Note 4) mw T ST Storage Temperature -65 to +5 o C Notes: 4. AP7 contains an internal thermal limiting circuit that is designed to protect the regulator in the event that the maximum junction temperature exceeded. When activated, typically at 5 C, the regulator output switches off and then back on as the die cools. Recommended Operating Conditions Symbol Parameter Min Max Unit T OP Operating Junction Temperature Range -4 5 o C AP7 Rev. 6 4 of MARCH 9

5 Electrical Characteristics (Under Operating Conditions) AP7 Parameter Conditions Min Typ. Max Unit Reference Voltage AP7-ADJ T A = 5 o C, (V IN- OUT) =.5V I O = ma V AP7-.5 I OUT = ma, T A = 5 o C, 3V V IN V V AP7-.8 I OUT = ma, T A = 5 o C, 3.3V V IN V V Output Voltage AP7-.5 I OUT = ma, T A = 5 o C, 4V V IN V V AP7-3.3 I OUT = ma, T A = 5 o C, 4.8V V IN V V AP7-5. I OUT = ma, T A = 5 o C, 6.5V V IN V V Line Regulation AP7-XXX I O = ma,v OUT+.5V<V IN<V, T A = 5 o C. % AP7-ADJ V IN=3.3V,Vadj=,mA<Io<A, T A = 5 o C (Note 5, 6) % AP7-.5 V IN = 3V, ma<io<a, T A = 5 o C (Note 5, 6) 5 mv Load Regulation AP7-.8 V IN = 3.3V, ma<io<a, T A = 5 o C (Note 5, 6) 5 8 mv AP7-.5 V IN = 4V, ma<io<a, T A = 5 o C (Note 5, 6) 5 mv AP7-3.3 V IN = 5V, I OUT A, T A = 5 o C (Note 5, 6) 6 33 mv AP7-5. V IN = 8V, I OUT A, T A = 5 o C (Note 5, 6) 4 5 mv Dropout Voltage AP7-ADJ/.5/.8 (V IN-V OUT) /.5/3.3/5. I OUT = A, ΔV OUT = %V OUT.3.4 V Current Limit AP7-ADJ/.5/.8 /.5/3.3/5. (V IN-V OUT) = 5V. A Minimum Load Current (Note 7) AP7-XXX o C T J 5 o C 5 ma Thermal Regulation T A = 5 o C, 3ms pulse.8.4 %/W Ripple Rejection F = 8Hz, C OUT = 5uF Tantalum, I OUT = A AP7-XXX V IN = V OUT+3V 6 7 db Temperature Stability I O = ma.5 % SOT89-3L: Control Circuitry/Power Transistor (Note 8) 64 SOT3-3L: Control Circuitry/Power Transistor (Note 9) 7 θ JA Thermal Resistance TO5-3L: Control Circuitry/Power Transistor (Note 8) 73 o C/W Junction-to-Ambient TO-3L: Control Circuitry/Power Transistor (Note 8) TO63-3L: Control Circuitry/Power Transistor (Note 8) 78 6 θ JC Thermal Resistance Junction-to-Case Notes: SOT89-3L: Control Circuitry/Power Transistor (Note 8) SOT3-3L: Control Circuitry/Power Transistor (Note 9) TO5-3L: Control Circuitry/Power Transistor (Note 8) TO-3L: Control Circuitry/Power Transistor (Note 8) TO63-3L: Control Circuitry/Power Transistor (Note 8) 5. See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = /8 from the package. 6. Line and load regulation are guaranteed up to the maximum power dissipation of 5W. Power dissipation is determined by the difference between input and output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. 7. Quiescent current is defined as the minimum output current required in maintaining regulation. At V input/output differential the device is guaranteed to regulate if the output current is greater than ma. 8. Test conditions for SOT89-3L, TO-3L, TO5-3L and TO63-3L: Devices mounted on FR-4 substrate, single sided PC board, oz copper, with minimum recommended pad layout, no air flow. The case point of θ JC is located on the thermal tab. 9. Test conditions for SOT3-3L: Devices mounted on FR-4 substrate, single sided PC board, oz copper, with 5mmx5mm thermal pad layout, no air flow. The case point of θ JC is located on the thermal tab o C/W AP7 Rev. 6 5 of MARCH 9

6 Typical Performance Characteristics AP Dropout Voltage (V) Tj = 5 o C Tj = 5 o C Output Voltage Deviation (%) I load=8ma Output Current (ma) Dropout Voltage vs Output Current Temperature ( o C) Load Regulation vs Temperature Output Voltage Change (%) Temperature ( o C) Percent Change in Output Voltage vs Temperature Output Voltage Deviation (%) Input Voltage (V) Line Regulation Output Voltage Deviation (mv) Input Voltage (V) 7.5 Cin=uF 6.5 Cout=uF Tantalum TIME (us) Line Transient Response Load Current (A) Output Voltage Deviation (mv) C in = uf C out = uf Tantalum Preload = ma TIME (us) Load Transient Response AP7 Rev. 6 6 of MARCH 9

7 AP7 Marking Information () SOT3-3L Logo Part Number 7 for ADJ 7-VV:5 for.5v 8 for.8v 5 for.5v 33 for 3.3V 5 for 5.V 7-VV Y W X Y : Year : ~9 W : Week : A~Z : ~6 week; a~z : 7~5 week; z repersents 5 and 53 week X : Internal code a~z : Lead Free A~Z : Green () TO5-3L Logo Part Number 7 for ADJ 7-VV:5 for.5v 8 for.8v 5 for.5v 33 for 3.3V 5 for 5.V 7-VV YY WW X X L : Lead Free G : Green YY : Year : ~9 WW : Week : ~5, 5 represents 5 and 53 week X : Internal Code AP7 Rev. 6 7 of MARCH 9

8 AP7 Marking Information (Continued) (3) SOT89-3L X X Y W X 3 XX : Identification code Y : Year : ~9 W : Week : A~Z : ~6 week; a~z : 7~5 week; z represents 5 and 53 week X : Internal code a~z : Lead Free A~Z : Green Marking Code Table Identification Code DA DB DC DD DE DF Output Version AP7-ADJ AP7-.5V AP7-.8V AP7-.5V AP7-3.3V AP7-5.V (4) TO63-3L Logo Part Number VV: 5 for.5v 8 for.8v 5 for.5v 33 for 3.3V 5 for 5.V Blank for ADJ 7-VV YY WW X X L : Lead Free YY : Year : ~9 WW : Week : ~5, 5 represents 5 and 53 week X : Internal code AP7 Rev. 6 8 of MARCH 9

9 AP7 Marking Information (Continued) (5) TO-3L Logo Part Number 7 for ADJ 7-VV : 5 for.5v 8 for.8v 5 for.5v 33 for 3.3V 5 for 5.V 7 - VV YY WW X X L : Lead Free YY : Year : ~9 WW : Week : ~5, 5 represents 5 and 53 week X : Internal code Package Information (All Dimensions in mm) () Package Type: SOT3-3L AP7 Rev. 6 9 of MARCH 9

10 Package Information (Continued) AP7 () Package Type: TO5-3L 6.354/6.8 Typ /5.5 Typ / /6. Typ Typ.8 BSC BSC..64/. Typ.83.89/.4. Land Pattern Recommendation (Unit: mm) 9./.4 Typ 9.7.8/.4 Typ.9.45/.58 Typ.5.5 SEE NOTE SEATING PLANE.45/.58 Typ.5 (3) Package Type: SOT89-3L.4/.75 Typ.6.7.8/..35/.6 Typ / (x).9/3. Typ /4.6 Typ Land Pattern Recommendation (Unit: mm) 5 (x).4/.6 Typ /.55 Typ.5.36/.48.4/.53 Typ.4 Typ.47.36/.48 Typ.4.35/.43 Typ.39 AP7 Rev. 6 of MARCH 9

11 Package Information (Continued) AP7 (4) Package Type: TO63-3L 9.65/.9 Typ Typ /9.65 Typ /5.88 Typ BSC..7/.78 Typ.5.5/.99 Typ.75.4/.4 Typ /4.83 Typ Land Pattern Recommendation (Unit: mm).38 Typ.54.8/.8 Typ.54.4/.4 Typ.7 (5) Package Type: TO-3L.54/3.43 Typ /.7 Typ. Ø3.53/4.9 Typ /4.85 Typ 4..5/.4 Typ.95 4./6.5 Typ /6.35 Typ /6.86 Typ 6.35 SEATING PLANE.4/.78 Typ.46.7/4.7 Typ /5.33 Typ 5.8.5/.4 Typ.83.99/.79 Typ.54.3/.4 Typ. 7.3/.9 Typ.48 AP7 Rev. 6 of MARCH 9

12 AP7 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which:. are intended to implant into the body, or. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright 9, Diodes Incorporated AP7 Rev. 6 of MARCH 9