RADIO RECEIVERS ECE 3103 WIRELESS COMMUNICATION SYSTEMS

Size: px
Start display at page:

Download "RADIO RECEIVERS ECE 3103 WIRELESS COMMUNICATION SYSTEMS"

Transcription

1 RADIO RECEIVERS ECE 3103 WIRELESS COMMUNICATION SYSTEMS

2 FUNCTIONS OF A RADIO RECEIVER The main functions of a radio receiver are: 1. To intercept the RF signal by using the receiver antenna 2. Select the desired RF signal and reject everything else 3. Amplify the RF signal 4. Detect the signal and demodulate to yield the original baseband signal 5. Amplify the baseband signal

3 CLASSIFICATION OF RECEIVERS Radio Receivers Operating Principle Application AM Radio FM Radio Radar Television Communication Tuned Radio Frequency Receivers Super heterodyne

4 TUNED RADIO FREQUENCY (TRF) RECEIVER Receiver Antenna RF STAGE DEMODULATOR/DETECTOR BASEBAND AMPLIFIER To Display/ Loud Speaker RF STAGE Two or Three RF Amplifiers Contains: input/output tuned circuits and RF amplifiers DEMODULATOR Signal is demodulated from the RF frequency to the baseband frequency BASEBAND AMPLIFIER Baseband signals amplified before being displayed or fed to a loud speaker

5 DRAWBACKS OF THE TRF RECEIVER/01 1. TRF receivers tend to oscillate due to a small part of the output leaks back to the input. This is due to the high gain and operation at the same frequency. Inter-stage Coupling Intra-stage Coupling X10 X10 X10 Avoiding this problem requires great care to shield and decouple each stage from all of the others. Signal strength, 1μV The effects of the feedback worsens as the operating frequency increases, compounding the difficulties of constructing sensitive, adjustable TRF receivers that will operate without oscillation over large frequency ranges.

6 DRAWBACKS OF THE TRF RECEIVER/02 2. TRF receivers have low selectivity, i.e ability to select the desired signal from the unwanted signal. This is because the passband of the receiver is broad 3. TRF receivers have higher bandwidth variation over the tuning range.

7 GENERAL RADIO RECEIVER REQUIREMENTS/01 1. Because the typical signal power level from the receive antenna may be as low as -100 to -120 dbm, the receiver may be required to provide gain as high as 100 to 120 db. 2. This much gain should be spread over the radio frequency and baseband stages to avoid instabilities and possible oscillation. 3. It is generally good practice to avoid more than about 50 db gain at any one stage.

8 GENERAL RADIO RECEIVER REQUIREMENTS/01 1. Good selectivity can be obtained by using a narrow Band Pass Filter (BPF) at the RF stage of the receiver. However, the bandwidth and cut-off requirements for such a filter are usually impractical to realize at RF frequencies. 2. It is more effective to achieve good selectivity by: a) Down-converting a relatively wide RF BW around the desired signal, and b) Using a sharp cut-off BPF at the Intermediate Frequency (IF) stage to select only the desired frequency band.

9 GENERAL RADIO RECEIVER REQUIREMENTS/01 Full-duplex communications systems usually use separate frequency bands for transmit and receive, thus avoiding the difficult (but not impossible) problem of isolating incoming and outgoing radiation at the same frequency. It is often preferred to use a single antenna for both transmit and receive. In this case it is necessary to use a duplexing filter to provide isolation between the Tx and Rx, while still providing a signal path with the antenna.

10 RADIO RECEIVER WITH INTERMEDIATE FREQUENCY (IF) STAGE RF AMPLIFIER STAGE MIXER IF AMPLIFIER STAGE DETECTOR/ DEMODULATOR BASEBAND AMPLIFIER To Display/ Loud Speaker OSCILLATOR

11 OPERATION OF A MIXER A mixer is basically a down-frequency translator in a radio receiver. Down converter Up converter Asin(2πf 1 t) Asin 2πf 1 t Bsin(2πf 2 t)= AB 2 cos 2π(f 1 f 2 ) cos 2π(f 1 + f 2 Bsin(2πf 2 t) Amplitude AB 2 f 1 f 2 f 1 + f 2 frequency

12 DIRECT CONVERSION RECEIVER/01 1. Direct Conversion receiver (also called homodyne receiver) uses a mixer and Local Oscillator to perform frequency down-conversion with a zero IF frequency. 2. Its features are: a) Uses two stage amplifiers b) No need for IF amp and filter c) No need for extra circuit for AM demodulation d) No image filter required e) High stable LO source required. 3. Homodyne receiver is often used with Doppler radars, where the exact receiver Local Oscillator frequency (LO) can be obtained from the transmitter.

13 DIRECT CONVERSION RECEIVER/02 1. Direct-conversion receivers convert an RF signal to a 0-IF signal in one stage. 2. Apart from Radar, they are used in low-cost solutions requiring few components and lend themselves to integrated-circuit (IC) designs. LNA Low Noise Amplifier

14 SUPER HETERODYNE RECEIVER 1. The superheterodyne (short for supersonic heterodyne) receiver was first evolved by Major Edwin Howard Armstrong, in It was introduced to the market place in the late 1920s and gradually phased out the TRF receiver during the 1930s. 3. Features of super heterodyne receiver are: a) A midrange IF allows the use of sharper cut-off filters for improved selectivity, and higher IF gain through the use of an IF amplifier. b) Tuning is conveniently accomplished by varying the frequency of the Local Oscillator so that the IF frequency remains constant. 4. Superhetrodyne receivers are used in a majority of broadcast radios and televisions, radar systems, cellular telephone systems, and data communications systems.

15 SINGLE CONVERSION SUPERHETERODYNE RF signal is mixed with a local oscillator signal to produce sum and difference frequency The lower frequency difference component called the intermediate frequency (IF), is separated from the other components by fixed tuned amplifier stages

16 MULTIPLE CONVERSION SUPERHETERODYNE 1. Receivers in HF and the VHF bands usually employ two (or more) stages of frequency conversion. 2. The lowest frequency IF channel provides the selectivity or bandwidth control that is needed. 3. The highest frequency IF channel is used to achieve good Image rejection.

17 FREQUENCY FILTERING Filtering is required in a superheterodyne receiver to provide 1. interference rejection, 2. image rejection, 3. selectivity, 4. suppression of Local Oscillator radiation

18 FILTERS IN SUPERHETERODYNE RECEIVER Pre-select filter Rejects out-of-band interference thus preventing strong interference signals from saturating the RF amplifier or mixer. Low-insertion loss Image reject filter Used reduce the effect of possible harmonic distortion from the RF amplifier IF Filter Sets the overall noise bandwidth of the receiver, as well as removing most unwanted mixer products.

19 LOCAL OSCILLATOR SIGNAL LEAKAGE 1. Local Oscillator (LO) signal lies in the RF pass band of the Receiver, and may pass back through the RF stages to be radiated by the antenna. 2. LO signal leakage usually minimized by: 1. combined attenuation of the preselect and image reject filters, 2. LO-RF isolation, 3. the reverse attenuation of the RF amplifier.

20 RECEIVER SENSITIVITY Receiver sensitivity describes how well a receiver can process very weak input signals. It is usually quantified as the weakest signal level that a receiver can detect to meet a given requirement, such as a specified signal-tonoise and distortion ratio or bit-error-rate (BER).

21 SENSITIVITY AND NOISE/01 Thermal noise represents the fundamental limit on achievable signal sensitivity. It is a result of the vibrations of conduction electrons and holes due to their finite temperature. Power delivered by a thermal source into a load is defined as: P = ktb where: k = Boltzmann s constant (1.38 x Joules/K); T = temperature in degrees Kelvin (K); B = noise bandwidth. The standard source noise temperature, or To, is 290 K. Therefore, the thermal noise generated in a 1-Hz bandwidth is: N o = KT = = -174 dbm/hz

22 MINIMUM DETECTABLE SIGNAL 1. Reliable communication requires a receive signal power at or above a certain minimum level, which we call the minimum detectable signal (MDS). 2. MDS determines the minimum SNR at the demodulator for a given system noise power.

23 MINIMUM DETECTABLE POWER

24 RECEIVER VOLTAGE SENSITIVITY OR SENSITIVITY The Minimum Detectable power, S imin can be converted to a minimum detectable signal voltage, for a given receiver input impedance

25 RECEIVER DYNAMIC RANGE Rx dynamic range is given by: The range depends on noise, modulation scheme, and required minimum SNR. The maximum allowable signal power could alternatively be defined by the third-order intercept point, P3, at the input to the receiver, as this would be the maximum input power before intermodulation distortion becomes unacceptable.

26 AUTOMATIC GAIN CONTROL/01 1. There is always need for about db of receiver gain to raise the minimum detectable signal to a usable level of approximately 10 mw (about 1 V peak at 50 ohm). 2. This gain is usually placed at the IF stage because: a) Amplifiers and other components are cheaper at lower frequencies. b) High input signal levels may exceed the P1dB,or IP3, of the front-end components if the gain of the early RF stages is too high. c) Moderate level of gain at the RF stage sets a good NF for the Rx system.

27 AUTOMATIC GAIN CONTROL/02 1. The power gain through the receiver must vary as a function of the input signal strength in order to fit the input signal range into the baseband processing range, for a wide range of input signal levels. 2. This variable-gain function is accomplished with an automatic gain control (AGC) circuit. 3. AGC is most often implemented at the IF stage.

28 IMPLEMENTING AGC 1. AGC consists of a variable voltage controlled attenuator or variable gain amplifier (VGA) with a detector to convert a sample of the IF voltage to a DC value. 2. The rectified signal is then compared with a reference level, and passed through a LPF to provide a time-constant long enough to avoid having the AGC following low-frequency components of the modulated signal.

29 Variable gain amplifier (VGA) Tracks the signal strength in order to fit the input signal range into the baseband processing range, for a wide range of input signal levels. DC AMP Sets threshold to avoid having the AGC following low-frequency components of the modulated signal

30 WHAT IS THE AGC DOING?

31

32 DUPLEXING Duplexer must be used to allow both the Tx and Rx to be connected to the antenna, while preventing the transmit signal from directly entering the receiver. Isolation between the Tx and Rx is required to be greater than 100 db.

33 HALF DUPLEX Half-duplex 1. If transmission and reception are not simultaneous, then T/R switch is used. 2. Diode switch can operate in microseconds and offer 40 db isolation, limiters and filters to increase isolation.

34 FULL DUPLEX To transmit and receive at different frequencies, Bandpass Filters are required for duplexer. The function of the filter is to: a) Provide some preselected filtering on receive. b) Attenuate spurious out-of-band signals from the transmitter. Duplexing filters often have insertion losses on the order of 1-3 db which degrades the Noise Figure of the Receiver.

35 DIPLEXER Vs DUPLEXER A diplexer is a three-port network that splits incoming signals from a common port into two paths depending on frequency. These frequency bands are usually wide apart. Example. Separation EGSM and GSM1800 Tx-Rx isolation is usually in the range db. Smart phones always use the LC Diplexer. A duplexer uses single antenna for both Tx and Rx at the same time. Both Tx and Rx paths have freq. bands very nearer, hence narrow BPF are used. Example: GSM uplink and downlink. Two types of duplexer, i.e one by using PIN diode switches and the other using circulators. Tx-Rx isolation is usually in the range db. Smart phone always use the SAW Duplexer

36 FM RECEIVER 1. Radio frequency range 88MHz MHz 2. Radio Station frequency 88 + n 75 KHz, n=1,2, Sensitivity - 10 μv 4. Intermediate Frequency (IF) 10.7 MHz f IF 10.7 MHz MHz

37 AM RADIO RECEIVER 1. Radio frequency range 535KHz KHz 2. Radio Station frequency n 10 KHz, n=1,2, Intermediate Frequency (IF) 455 KHz

38 ANALOGUE TV RECEIVER TUNER TV Receiver tuner amplifies the RF signal picked up by the antenna and converts the carrier frequencies and their associated bands into the intermediate frequencies and their sidebands

39 The standard intermediate frequencies for the 625-B system are- Picture IF = 38.9 MHz, Sound IF = 33.4 MHz

40 GSM Transmitter/Receiver (Showing only Receive) LNA 900-MHz RF input is filtered, amplified and applied to the first stage mixer. Transmit/Receive Oscillator Usually controlled by the 26MHz crystal Frequency Synthesizer 26MHz Crystal 1 st Mixer LO must have a range of 640 MHz to 675 MHz in order to cover the RF input band, i.e MHz. f m = MHz = 10.7 MHz

Receiver Design. Prof. Tzong-Lin Wu EMC Laboratory Department of Electrical Engineering National Taiwan University 2011/2/21

Receiver Design. Prof. Tzong-Lin Wu EMC Laboratory Department of Electrical Engineering National Taiwan University 2011/2/21 Receiver Design Prof. Tzong-Lin Wu EMC Laboratory Department of Electrical Engineering National Taiwan University 2011/2/21 MW & RF Design / Prof. T. -L. Wu 1 The receiver mush be very sensitive to -110dBm

More information

Introduction to Receivers

Introduction to Receivers Introduction to Receivers Purpose: translate RF signals to baseband Shift frequency Amplify Filter Demodulate Why is this a challenge? Interference Large dynamic range required Many receivers must be capable

More information

Module 8 Theory. dbs AM Detector Ring Modulator Receiver Chain. Functional Blocks Parameters. IRTS Region 4

Module 8 Theory. dbs AM Detector Ring Modulator Receiver Chain. Functional Blocks Parameters. IRTS Region 4 Module 8 Theory dbs AM Detector Ring Modulator Receiver Chain Functional Blocks Parameters Decibel (db) The term db or decibel is a relative unit of measurement used frequently in electronic communications

More information

ELEN 701 RF & Microwave Systems Engineering. Lecture 2 September 27, 2006 Dr. Michael Thorburn Santa Clara University

ELEN 701 RF & Microwave Systems Engineering. Lecture 2 September 27, 2006 Dr. Michael Thorburn Santa Clara University ELEN 701 RF & Microwave Systems Engineering Lecture 2 September 27, 2006 Dr. Michael Thorburn Santa Clara University Lecture 2 Radio Architecture and Design Considerations, Part I Architecture Superheterodyne

More information

HF Receivers, Part 2

HF Receivers, Part 2 HF Receivers, Part 2 Superhet building blocks: AM, SSB/CW, FM receivers Adam Farson VA7OJ View an excellent tutorial on receivers NSARC HF Operators HF Receivers 2 1 The RF Amplifier (Preamp)! Typical

More information

RF/IF Terminology and Specs

RF/IF Terminology and Specs RF/IF Terminology and Specs Contributors: Brad Brannon John Greichen Leo McHugh Eamon Nash Eberhard Brunner 1 Terminology LNA - Low-Noise Amplifier. A specialized amplifier to boost the very small received

More information

Technician License Course Chapter 3 Types of Radios and Radio Circuits. Module 7

Technician License Course Chapter 3 Types of Radios and Radio Circuits. Module 7 Technician License Course Chapter 3 Types of Radios and Radio Circuits Module 7 Radio Block Diagrams Radio Circuits can be shown as functional blocks connected together. Knowing the description of common

More information

Receiver Architecture

Receiver Architecture Receiver Architecture Receiver basics Channel selection why not at RF? BPF first or LNA first? Direct digitization of RF signal Receiver architectures Sub-sampling receiver noise problem Heterodyne receiver

More information

Wideband Receiver for Communications Receiver or Spectrum Analysis Usage: A Comparison of Superheterodyne to Quadrature Down Conversion

Wideband Receiver for Communications Receiver or Spectrum Analysis Usage: A Comparison of Superheterodyne to Quadrature Down Conversion A Comparison of Superheterodyne to Quadrature Down Conversion Tony Manicone, Vanteon Corporation There are many different system architectures which can be used in the design of High Frequency wideband

More information

Radio Receivers. Al Penney VO1NO

Radio Receivers. Al Penney VO1NO Radio Receivers Role of the Receiver The Antenna must capture the radio wave. The desired frequency must be selected from all the EM waves captured by the antenna. The selected signal is usually very weak

More information

Radio Receiver Architectures and Analysis

Radio Receiver Architectures and Analysis Radio Receiver Architectures and Analysis Robert Wilson December 6, 01 Abstract This article discusses some common receiver architectures and analyzes some of the impairments that apply to each. 1 Contents

More information

Television and video engineering

Television and video engineering Television and video engineering Unit-4 Television Receiver systems Objectives: To learn the requirements of TV receiver Study of monochrome and Colour TV receivers. To learn functions of Tuning circuits

More information

Radio Receivers. Al Penney VO1NO

Radio Receivers. Al Penney VO1NO Radio Receivers Al Penney VO1NO Role of the Receiver The Antenna must capture the radio wave. The desired frequency must be selected from all the EM waves captured by the antenna. The selected signal is

More information

TSEK38: Radio Frequency Transceiver Design Lecture 3: Superheterodyne TRX design

TSEK38: Radio Frequency Transceiver Design Lecture 3: Superheterodyne TRX design TSEK38: Radio Frequency Transceiver Design Lecture 3: Superheterodyne TRX design Ted Johansson, ISY ted.johansson@liu.se 2 Outline of lecture 3 Introduction RF TRX architectures (3) Superheterodyne architecture

More information

RF Integrated Circuits

RF Integrated Circuits Introduction and Motivation RF Integrated Circuits The recent explosion in the radio frequency (RF) and wireless market has caught the semiconductor industry by surprise. The increasing demand for affordable

More information

RFID Systems: Radio Architecture

RFID Systems: Radio Architecture RFID Systems: Radio Architecture 1 A discussion of radio architecture and RFID. What are the critical pieces? Familiarity with how radio and especially RFID radios are designed will allow you to make correct

More information

INTRODUCTION TO TRANSCEIVER DESIGN ECE3103 ADVANCED TELECOMMUNICATION SYSTEMS

INTRODUCTION TO TRANSCEIVER DESIGN ECE3103 ADVANCED TELECOMMUNICATION SYSTEMS INTRODUCTION TO TRANSCEIVER DESIGN ECE3103 ADVANCED TELECOMMUNICATION SYSTEMS FUNCTIONS OF A TRANSMITTER The basic functions of a transmitter are: a) up-conversion: move signal to desired RF carrier frequency.

More information

Lecture 6 SIGNAL PROCESSING. Radar Signal Processing Dr. Aamer Iqbal Bhatti. Dr. Aamer Iqbal Bhatti

Lecture 6 SIGNAL PROCESSING. Radar Signal Processing Dr. Aamer Iqbal Bhatti. Dr. Aamer Iqbal Bhatti Lecture 6 SIGNAL PROCESSING Signal Reception Receiver Bandwidth Pulse Shape Power Relation Beam Width Pulse Repetition Frequency Antenna Gain Radar Cross Section of Target. Signal-to-noise ratio Receiver

More information

Superheterodyne Receiver Tutorial

Superheterodyne Receiver Tutorial 1 of 6 Superheterodyne Receiver Tutorial J P Silver E-mail: john@rfic.co.uk 1 ABSTRACT This paper discusses the basic design concepts of the Superheterodyne receiver in both single and double conversion

More information

High Dynamic Range Receiver Parameters

High Dynamic Range Receiver Parameters High Dynamic Range Receiver Parameters The concept of a high-dynamic-range receiver implies more than an ability to detect, with low distortion, desired signals differing, in amplitude by as much as 90

More information

Session 3. CMOS RF IC Design Principles

Session 3. CMOS RF IC Design Principles Session 3 CMOS RF IC Design Principles Session Delivered by: D. Varun 1 Session Topics Standards RF wireless communications Multi standard RF transceivers RF front end architectures Frequency down conversion

More information

ADI 2006 RF Seminar. Chapter II RF/IF Components and Specifications for Receivers

ADI 2006 RF Seminar. Chapter II RF/IF Components and Specifications for Receivers ADI 2006 RF Seminar Chapter II RF/IF Components and Specifications for Receivers 1 RF/IF Components and Specifications for Receivers Fixed Gain and Variable Gain Amplifiers IQ Demodulators Analog-to-Digital

More information

INTRODUCTION TO COMMUNICATION SYSTEMS AND TRANSMISSION MEDIA

INTRODUCTION TO COMMUNICATION SYSTEMS AND TRANSMISSION MEDIA COMM.ENG INTRODUCTION TO COMMUNICATION SYSTEMS AND TRANSMISSION MEDIA 9/9/2017 LECTURES 1 Objectives To give a background on Communication system components and channels (media) A distinction between analogue

More information

Co-existence. DECT/CAT-iq vs. other wireless technologies from a HW perspective

Co-existence. DECT/CAT-iq vs. other wireless technologies from a HW perspective Co-existence DECT/CAT-iq vs. other wireless technologies from a HW perspective Abstract: This White Paper addresses three different co-existence issues (blocking, sideband interference, and inter-modulation)

More information

IC-R8500 Test Report. By Adam Farson VA7OJ/AB4OJ

IC-R8500 Test Report. By Adam Farson VA7OJ/AB4OJ IC-R8500 Test Report By Adam Farson VA7OJ/AB4OJ Iss. 1, Dec. 14, 2015. Figure 1: The Icom IC-R8500. Introduction: This report presents results of an RF lab test suite performed on the IC- R8500 receiver.

More information

OBJECTIVES EQUIPMENT LIST

OBJECTIVES EQUIPMENT LIST 1 Reception of Amplitude Modulated Signals AM Demodulation OBJECTIVES The purpose of this experiment is to show how the amplitude-modulated signals are demodulated to obtain the original signal. Also,

More information

CHAPTER - 6 PIN DIODE CONTROL CIRCUITS FOR WIRELESS COMMUNICATIONS SYSTEMS

CHAPTER - 6 PIN DIODE CONTROL CIRCUITS FOR WIRELESS COMMUNICATIONS SYSTEMS CHAPTER - 6 PIN DIODE CONTROL CIRCUITS FOR WIRELESS COMMUNICATIONS SYSTEMS 2 NOTES 3 INTRODUCTION PIN DIODE CONTROL CIRCUITS FOR WIRELESS COMMUNICATIONS SYSTEMS Chapter 6 discusses PIN Control Circuits

More information

TSEK02: Radio Electronics Lecture 8: RX Nonlinearity Issues, Demodulation. Ted Johansson, EKS, ISY

TSEK02: Radio Electronics Lecture 8: RX Nonlinearity Issues, Demodulation. Ted Johansson, EKS, ISY TSEK02: Radio Electronics Lecture 8: RX Nonlinearity Issues, Demodulation Ted Johansson, EKS, ISY 2 RX Nonlinearity Issues, Demodulation RX nonlinearities (parts of 2.2) System Nonlinearity Sensitivity

More information

TSEK02: Radio Electronics Lecture 8: RX Nonlinearity Issues, Demodulation. Ted Johansson, EKS, ISY

TSEK02: Radio Electronics Lecture 8: RX Nonlinearity Issues, Demodulation. Ted Johansson, EKS, ISY TSEK02: Radio Electronics Lecture 8: RX Nonlinearity Issues, Demodulation Ted Johansson, EKS, ISY RX Nonlinearity Issues: 2.2, 2.4 Demodulation: not in the book 2 RX nonlinearities System Nonlinearity

More information

Chapter 3. Question Mar No

Chapter 3. Question Mar No Chapter 3 Sr Question Mar No k. 1 Write any two drawbacks of TRF radio receiver 1. Instability due to oscillatory nature of RF amplifier.. Variation in bandwidth over tuning range. 3. Insufficient selectivity

More information

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 678A 40MHZ TO 900MHZ DIRECT CONVERSION QUADRATURE DEMODULATOR

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 678A 40MHZ TO 900MHZ DIRECT CONVERSION QUADRATURE DEMODULATOR DESCRIPTION QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 678A LT5517 Demonstration circuit 678A is a 40MHz to 900MHz Direct Conversion Quadrature Demodulator featuring the LT5517. The LT 5517 is a direct

More information

1 Introduction to Highly Integrated and Tunable RF Receiver Front Ends

1 Introduction to Highly Integrated and Tunable RF Receiver Front Ends 1 Introduction to Highly Integrated and Tunable RF Receiver Front Ends 1.1 Introduction With the ever-increasing demand for instant access to data over wideband communication channels, the quest for a

More information

HF Receivers, Part 3

HF Receivers, Part 3 HF Receivers, Part 3 Introduction to frequency synthesis; ancillary receiver functions Adam Farson VA7OJ View an excellent tutorial on receivers Another link to receiver principles NSARC HF Operators HF

More information

RF Receiver Hardware Design

RF Receiver Hardware Design RF Receiver Hardware Design Bill Sward bsward@rtlogic.com February 18, 2011 Topics Customer Requirements Communication link environment Performance Parameters/Metrics Frequency Conversion Architectures

More information

COMM 704: Communication Systems

COMM 704: Communication Systems COMM 704: Communication Lecture 1: Introduction Dr. Mohamed Abd El Ghany, Mohamed.abdel-ghany@guc.edu.eg Course Objective Give an introduction to the basic concepts of electronic communication systems

More information

RF System Aspects for SDR. A Tutorial. Dr. Ruediger Leschhorn, Rohde & Schwarz 29. November 2011

RF System Aspects for SDR. A Tutorial. Dr. Ruediger Leschhorn, Rohde & Schwarz 29. November 2011 RF System Aspects for SDR A Tutorial Dr. Ruediger Leschhorn, Rohde & Schwarz 29. November 2011 Content Radio System Some Basics Link Budget Cosite Examples Desensitization Blocking, Transmitter Noise,

More information

Outline. Communications Engineering 1

Outline. Communications Engineering 1 Outline Introduction Signal, random variable, random process and spectra Analog modulation Analog to digital conversion Digital transmission through baseband channels Signal space representation Optimal

More information

ELEN 701 RF & Microwave Systems Engineering. Lecture 4 October 11, 2006 Dr. Michael Thorburn Santa Clara University

ELEN 701 RF & Microwave Systems Engineering. Lecture 4 October 11, 2006 Dr. Michael Thorburn Santa Clara University ELEN 7 RF & Microwave Systems Engineering Lecture 4 October, 26 Dr. Michael Thorburn Santa Clara University Lecture 5 Receiver System Analysis and Design, Part II Key Parameters Intermodulation Characteristics

More information

EE470 Electronic Communication Theory Exam II

EE470 Electronic Communication Theory Exam II EE470 Electronic Communication Theory Exam II Open text, closed notes. For partial credit, you must show all formulas in symbolic form and you must work neatly!!! Date: November 6, 2013 Name: 1. [16%]

More information

TDA7000 for narrowband FM reception

TDA7000 for narrowband FM reception TDA7 for narrowband FM reception Author: Author: W.V. Dooremolen INTRODUCTION Today s cordless telephone sets make use of duplex communication with carrier frequencies of about.7mhz and 49MHz. In the base

More information

The New England Radio Discussion Society electronics course (Phase 4, cont d) Introduction to receivers

The New England Radio Discussion Society electronics course (Phase 4, cont d) Introduction to receivers The New England Radio Discussion Society electronics course (Phase 4, cont d) Introduction to receivers AI2Q April 2017 REVIEW: a VFO, phase-locked loop (PLL), or direct digital synthesizer (DDS), can

More information

RF Interference Cancellation - a Key Technology to support an Integrated Communications Environment

RF Interference Cancellation - a Key Technology to support an Integrated Communications Environment RF Interference Cancellation - a Key Technology to support an Integrated Communications Environment Abstract Steve Nightingale, Giles Capps, Craig Winter and George Woloszczuk Cobham Technical Services,

More information

Topic Advanced Radio Receivers. Explain that an RF amplifier can be used to improve sensitivity;

Topic Advanced Radio Receivers. Explain that an RF amplifier can be used to improve sensitivity; Learning Objectives: At the end of this topic you will be able to; Explain that an RF amplifier can be used to improve sensitivity; Explain that a superheterodyne receiver offers improved selectivity and

More information

VLF-LF Up Converter 5KHz - 500KHz. User manual. Rev HEROS technology Limited All rights reserved

VLF-LF Up Converter 5KHz - 500KHz. User manual. Rev HEROS technology Limited All rights reserved VLF-LF Up Converter 5KHz - 500KHz User manual. Rev 2016-02 Since many countries are allocating the 472 khz to 479kHZ band for experimental use by Radio Amateurs, a growing number of them as well as listeners

More information

ENSC327 Communications Systems 5: Frequency Translation (3.6) and Superhet Receiver (3.9)

ENSC327 Communications Systems 5: Frequency Translation (3.6) and Superhet Receiver (3.9) ENSC327 Communications Systems 5: Frequency Translation (3.6) and Superhet Receiver (3.9) Jie Liang School o Engineering Science Simon Fraser University 1 Outline Frequency translation (page 128) Superhet

More information

NEW YORK CITY COLLEGE of TECHNOLOGY THE CITY UNIVERSITY OF NEW YORK DEPARTMENT OF ELECTRICAL ENGINEERING AND TELECOMMUNICATIONS TECHNOLOGIES

NEW YORK CITY COLLEGE of TECHNOLOGY THE CITY UNIVERSITY OF NEW YORK DEPARTMENT OF ELECTRICAL ENGINEERING AND TELECOMMUNICATIONS TECHNOLOGIES NEW YORK CITY COLLEGE of TECHNOLOGY THE CITY UNIVERSITY OF NEW YORK DEPARTMENT OF ELECTRICAL ENGINEERING AND TELECOMMUNICATIONS TECHNOLOGIES Course : EET 24 Communications Electronics Module : AM Tx and

More information

Interference & Suppression Page 59

Interference & Suppression Page 59 INTERFERENCE Interference & Suppression Page 59 Front-End Overload, Cross-Modulation What is meant by receiver overload? Interference caused by strong signals from a nearby transmitter What is one way

More information

HF Receiver Testing: Issues & Advances (also presented at APDXC 2014, Osaka, Japan, November 2014) Adam Farson VA7OJ Copyright 2014 North Shore Amateur Radio Club NSARC HF Operators HF RX Testing 1 HF

More information

FM Superheterodyne Receiver

FM Superheterodyne Receiver EE321 Final Project Chun-Hao Lo XiaoKai Sun Background: FM Superheterodyne Receiver Superheterodyne Receiver is the receiver that convert a received signal from the transmitter to an intermediate frequency.

More information

Wideband Receiver Design

Wideband Receiver Design Wideband Receiver Design Challenges and Trade-offs of a Wideband Tuning Range in Wireless Microphone Receivers in the UHF Television Band About this White Paper Professional wireless microphone systems

More information

Introduction Introduction to radio frequencies p. 3 What are the 'radio frequencies'? p. 3 Why are radio frequencies different? p.

Introduction Introduction to radio frequencies p. 3 What are the 'radio frequencies'? p. 3 Why are radio frequencies different? p. Foreword p. xi Preface p. xiii Introduction Introduction to radio frequencies p. 3 What are the 'radio frequencies'? p. 3 Why are radio frequencies different? p. 3 What this book covers p. 3 Signals and

More information

CHAPTER 13 TRANSMITTERS AND RECEIVERS

CHAPTER 13 TRANSMITTERS AND RECEIVERS CHAPTER 13 TRANSMITTERS AND RECEIVERS Frequency Modulation (FM) Receiver Frequency Modulation (FM) Receiver FREQUENCY MODULATION (FM) RECEIVER Superheterodyne Receiver Heterodyning The word heterodyne

More information

Communication Systems, 5e

Communication Systems, 5e Communiation Systems, 5e Chapter 7: Analog Communiation Systems A. Brue Carlson Paul B. Crilly 010 The Mraw-Hill Companies Chapter 7: Analog Communiation Systems Reeiver blok diagram design Image requeny

More information

THE BASICS OF RADIO SYSTEM DESIGN

THE BASICS OF RADIO SYSTEM DESIGN THE BASICS OF RADIO SYSTEM DESIGN Mark Hunter * Abstract This paper is intended to give an overview of the design of radio transceivers to the engineer new to the field. It is shown how the requirements

More information

Today s communication

Today s communication From October 2009 High Frequency Electronics Copyright 2009 Summit Technical Media, LLC Selecting High-Linearity Mixers for Wireless Base Stations By Stephanie Overhoff Maxim Integrated Products, Inc.

More information

Technician License Course Chapter 3. Lesson Plan Module 7 Types of Radio Circuits

Technician License Course Chapter 3. Lesson Plan Module 7 Types of Radio Circuits Technician License Course Chapter 3 Lesson Plan Module 7 Types of Radio Circuits The Basic Transceiver Combination of transmitter and receiver Abbreviated XCVR (X = trans) Antenna switched between transmitter

More information

INSTALLATION AND OPERATING MANUAL

INSTALLATION AND OPERATING MANUAL INSTALLATION AND OPERATING MANUAL FOR RBDA-PCS-1/25W-90-A INDOOR REPEATER TABLE OF CONTENTS PARAGRAPH PAGE NO BDA OVERVIEW 3 BDA BLOCK DIAGRAM DESCRIPTION 3 FCC INFORMATION FOR USER 3 BDA BLOCK DIAGRAM

More information

The 144MHz Anglian 3 transverter

The 144MHz Anglian 3 transverter The 144MHz Anglian 3 transverter A high performance 144/28MHz transverter G4DDK document issue 1 12/9/16 Introduction Anglian 3 is an update to the 144MHz Anglian 2 transverter. The Anglian 2 is no longer

More information

Solution: NF=6 db, B=2.1 GHz, SNR min =7dB T=290 k, P in,1db = 10.5 dbm

Solution: NF=6 db, B=2.1 GHz, SNR min =7dB T=290 k, P in,1db = 10.5 dbm Consider a receiver with a noise figure of 6 db and a bandwidth of 2.1 GHz operating at room temperature. The input 1-dB compression point is 10.5 dbm and the detector at receiver output requires a minimum

More information

14 MHz Single Side Band Receiver

14 MHz Single Side Band Receiver EPFL - LEG Laboratoires à options 8 ème semestre MHz Single Side Band Receiver. Objectives. The objective of this work is to calculate and adjust the key elements of an Upper Side Band Receiver in the

More information

Amplitude Modulated Systems

Amplitude Modulated Systems Amplitude Modulated Systems Communication is process of establishing connection between two points for information exchange. Channel refers to medium through which message travels e.g. wires, links, or

More information

VLF LF 10KHz - 500KHz Up Converter. Brochure. HEROS technology Limited All rights reserved

VLF LF 10KHz - 500KHz Up Converter. Brochure. HEROS technology Limited All rights reserved Brochure Since many countries are allocating the old 500KHz (600m) maritime radio distress band for experimental use by Radio Amateurs, a growing number of them as well as listeners have become interested

More information

: Triple PLL, lowest reference frequency 10 khz. : ± 5 khz in 10 Hz steps, synthesized.

: Triple PLL, lowest reference frequency 10 khz. : ± 5 khz in 10 Hz steps, synthesized. PETER DE CONINCK HAGENUK RX 1001MVB RECEIVER ONL4234 SERIAL N 5820-310-6162 BELGIAN SWL DRAWING N 97 8 2.164 Technical data Frequency range Frequency resolution Frequency tuning Frequency synthesizer Frequency

More information

MAINTENANCE MANUAL TRANSMITTER/RECEIVER BOARD CMN-234A/B FOR MLSU141 & MLSU241 UHF MOBILE RADIO TABLE OF CONTENTS

MAINTENANCE MANUAL TRANSMITTER/RECEIVER BOARD CMN-234A/B FOR MLSU141 & MLSU241 UHF MOBILE RADIO TABLE OF CONTENTS MAINTENANCE MANUAL TRANSMITTER/RECEIVER BOARD CMN-234A/B FOR MLSU141 & MLSU241 UHF MOBILE RADIO TABLE OF CONTENTS DESCRIPTION... 2 CIRCUIT ANALYSIS... 2 TRANSMITTER... 2 9-Voft Regulator... 2 Exciter...

More information

HY448 Sample Problems

HY448 Sample Problems HY448 Sample Problems 10 November 2014 These sample problems include the material in the lectures and the guided lab exercises. 1 Part 1 1.1 Combining logarithmic quantities A carrier signal with power

More information

4- Single Side Band (SSB)

4- Single Side Band (SSB) 4- Single Side Band (SSB) It can be shown that: s(t) S.S.B = m(t) cos ω c t ± m h (t) sin ω c t -: USB ; +: LSB m(t) X m(t) cos ω c t -π/ cos ω c t -π/ + s S.S.B m h (t) X m h (t) ± sin ω c t 1 Tone Modulation:

More information

The Friis Transmission Formula

The Friis Transmission Formula The Friis Transmission Formula If we assume that the antennas are aligned for maximum transmission and reception, then in free space, P RX = G TXA e P TX 4πr 2 where A e is the receiving aperture of the

More information

RF Components and Circuits

RF Components and Circuits RF Components and Circuits RF Components and Circuits Joseph J. Carr Newnes OXFORD AMSTERDAM BOSTON LONDON NEW YORK PARIS SAN DIEGO SAN FRANCISCO SINGAPORE SYDNEY TOKYO Newnes An imprint of Elsevier Science

More information

Low Distortion Mixer AD831

Low Distortion Mixer AD831 a FEATURES Doubly-Balanced Mixer Low Distortion +2 dbm Third Order Intercept (IP3) + dbm 1 db Compression Point Low LO Drive Required: dbm Bandwidth MHz RF and LO Input Bandwidths 2 MHz Differential Current

More information

Understanding Mixers Terms Defined, and Measuring Performance

Understanding Mixers Terms Defined, and Measuring Performance Understanding Mixers Terms Defined, and Measuring Performance Mixer Terms Defined Statistical Processing Applied to Mixers Today's stringent demands for precise electronic systems place a heavy burden

More information

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK v01.05.00 HMC141/142 MIXER OPERATION

More information

VLF-LF-MF Up Converter

VLF-LF-MF Up Converter VLF-LF-MF Up Converter 5kHz-500kHz 3.5MHz-4MHz model 350 4MHz-4.5MHz model 400 User manual. Rev 2018-01 Since many countries are allocating the 472 khz to 479kHZ band for experimental use by Radio Amateurs,

More information

Tuned Radio Frequency Receiver (TRF) The most elementary receiver design, consisting of RF amplifier stages, detector and audio amplifier stages.

Tuned Radio Frequency Receiver (TRF) The most elementary receiver design, consisting of RF amplifier stages, detector and audio amplifier stages. Figure 3-1 Simple radio receiver block diagram. Tuned Radio Frequency Receiver (TRF) The most elementary receiver design, consisting of RF amplifier stages, detector and audio amplifier stages. Jeffrey

More information

TSEK38: Radio Frequency Transceiver Design Lecture 6: Receiver Synthesis (I)

TSEK38: Radio Frequency Transceiver Design Lecture 6: Receiver Synthesis (I) TSEK38: Radio Frequency Transceiver Design Lecture 6: Receiver Synthesis (I) Ted Johansson, ISY ted.johansson@liu.se Systematic Receiver Synthesis (1) 4.1 Introduction 4. Sensitivity, Noise Figure Receiver

More information

An All CMOS, 2.4 GHz, Fully Adaptive, Scalable, Frequency Hopped Transceiver

An All CMOS, 2.4 GHz, Fully Adaptive, Scalable, Frequency Hopped Transceiver An All CMOS, 2.4 GHz, Fully Adaptive, Scalable, Frequency Hopped Transceiver Farbod Behbahani John Leete Alexandre Kral Shahrzad Tadjpour Karapet Khanoyan Paul J. Chang Hooman Darabi Maryam Rofougaran

More information

Using measurement methods described in Australian/New Zealand Standard AS/NZS 4770:2000

Using measurement methods described in Australian/New Zealand Standard AS/NZS 4770:2000 Barrett 2050 HF transceiver Using measurement methods described in Australian/New Zealand Standard AS/NZS 4770:2000 General Specifications Equipment Standards Transmit frequency range Receive frequency

More information

Software Defined Radio in Ham Radio Dennis Silage K3DS TS EPA Section ARRL

Software Defined Radio in Ham Radio Dennis Silage K3DS TS EPA Section ARRL Software Defined Radio in Ham Radio Dennis Silage K3DS silage@arrl.net TS EPA Section ARRL TUARC K3TU SDR in HR The crystal radio was once a simple introduction to radio electronics and Amateur Radio.

More information

TSEK38: Radio Frequency Transceiver Design Lecture 7: Receiver Synthesis (II)

TSEK38: Radio Frequency Transceiver Design Lecture 7: Receiver Synthesis (II) TSEK38: Radio Frequency Transceiver Design Lecture 7: Receiver Synthesis (II) Ted Johansson, ISY ted.johansson@liu.se Systematic Receiver Synthesis (II) 4.3 Intermodulation characteristics Phase noise

More information

Instrumentation Receiver: Analog Signal Processing for a DSP World. Rick Campbell Portland State University

Instrumentation Receiver: Analog Signal Processing for a DSP World. Rick Campbell Portland State University Instrumentation Receiver: Analog Signal Processing for a DSP World Rick Campbell Portland State University Tonight s Talk discusses 3 questions: What is an Instrumentation Receiver? How does Rick design

More information

B.Tech II Year II Semester (R13) Supplementary Examinations May/June 2017 ANALOG COMMUNICATION SYSTEMS (Electronics and Communication Engineering)

B.Tech II Year II Semester (R13) Supplementary Examinations May/June 2017 ANALOG COMMUNICATION SYSTEMS (Electronics and Communication Engineering) Code: 13A04404 R13 B.Tech II Year II Semester (R13) Supplementary Examinations May/June 2017 ANALOG COMMUNICATION SYSTEMS (Electronics and Communication Engineering) Time: 3 hours Max. Marks: 70 PART A

More information

CHAPTER 3 CMOS LOW NOISE AMPLIFIERS

CHAPTER 3 CMOS LOW NOISE AMPLIFIERS 46 CHAPTER 3 CMOS LOW NOISE AMPLIFIERS 3.1 INTRODUCTION The Low Noise Amplifier (LNA) plays an important role in the receiver design. LNA serves as the first block in the RF receiver. It is a critical

More information

1. Explain how Doppler direction is identified with FMCW radar. Fig Block diagram of FM-CW radar. f b (up) = f r - f d. f b (down) = f r + f d

1. Explain how Doppler direction is identified with FMCW radar. Fig Block diagram of FM-CW radar. f b (up) = f r - f d. f b (down) = f r + f d 1. Explain how Doppler direction is identified with FMCW radar. A block diagram illustrating the principle of the FM-CW radar is shown in Fig. 4.1.1 A portion of the transmitter signal acts as the reference

More information

Interference Issues between UMTS & WLAN in a Multi-Standard RF Receiver

Interference Issues between UMTS & WLAN in a Multi-Standard RF Receiver Interference Issues between UMTS & WLAN in a Multi-Standard RF Receiver Nastaran Behjou, Basuki E. Priyanto, Ole Kiel Jensen, and Torben Larsen RISC Division, Department of Communication Technology, Aalborg

More information

ARRL Laboratory Expanded Test-Result Report ICOM IC-7800

ARRL Laboratory Expanded Test-Result Report ICOM IC-7800 ARRL Laboratory Expanded Test-Result Report ICOM IC-78 Prepared by: American Radio Relay League, Inc. Technical Department Laboratory 225 Main St. Newington, CT 6111 Telephone: (86) 594-214 Internet: mtracy@arrl.org

More information

Receiver Architectures

Receiver Architectures Receiver Architectures Direct Detection of radio signals 1 2.. n f C,i Antenna Amplifier RF Filter A Demodulation Base Band 1 f C,i Not convenient: - RF filter must be very selective and tunable - Amplifier

More information

Modern radio techniques

Modern radio techniques Modern radio techniques for probing the ionosphere Receiver, radar, advanced ionospheric sounder, and related techniques Cesidio Bianchi INGV - Roma Italy Ionospheric properties related to radio waves

More information

User Manual. User Manual. Wide Band Booster (30dBm) 2012 February. Information in this manual is subject to change without notice

User Manual. User Manual. Wide Band Booster (30dBm) 2012 February. Information in this manual is subject to change without notice User Manual Wide Band Booster (30dBm) 2012 February Information in this manual is subject to change without notice 1 Table of Contents 1 Overview... 3 2 System Diagram... 4 3 Technical Specification...

More information

Transmitters and receivers

Transmitters and receivers Chapter 3 Transmitters and receivers Transmitters and receivers are used extensively in aircraft communication and navigation systems. In conjunction with one ore more antennas, they are responsible for

More information

Introduction to Surface Acoustic Wave (SAW) Devices

Introduction to Surface Acoustic Wave (SAW) Devices May 31, 2018 Introduction to Surface Acoustic Wave (SAW) Devices Part 7: Basics of RF Circuits Ken-ya Hashimoto Chiba University k.hashimoto@ieee.org http://www.te.chiba-u.jp/~ken Contents Noise Figure

More information

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED

Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK 17 Product Application Notes Introduction

More information

MICROWAVE RADIO SYSTEMS GAIN. PENTel.Com Engr. Josephine Bagay, Ece faculty

MICROWAVE RADIO SYSTEMS GAIN. PENTel.Com Engr. Josephine Bagay, Ece faculty MICROWAVE RADIO SYSTEMS GAIN PENTel.Com Engr. Josephine Bagay, Ece faculty SYSTEM GAIN G s is the difference between the nominal output power of a transmitter (P t ) and the minimum input power to a receiver

More information

VHF LAND MOBILE SERVICE

VHF LAND MOBILE SERVICE RFS21 December 1991 (Issue 1) SPECIFICATION FOR RADIO APPARATUS: VHF LAND MOBILE SERVICE USING AMPLITUDE MODULATION WITH 12.5 khz CARRIER FREQUENCY SEPARATION Communications Division Ministry of Commerce

More information

Interference Analysis and Spectrum Monitor Seminar

Interference Analysis and Spectrum Monitor Seminar Interference Analysis and Spectrum Monitor Seminar Handheld RF & Microwave Instruments Andrew Benn Business Development Manager Agilent Technologies Wednesday 12 th October 2011 1 Agilent Technologies,

More information

Maintenance Manual TRANSMITTER/RECEIVER BOARD CMN-233 FOR MLSH041

Maintenance Manual TRANSMITTER/RECEIVER BOARD CMN-233 FOR MLSH041 Maintenance Manual TRANSMITTER/RECEIVER BOARD CMN-233 FOR MLSH041 TABLE OF CONTENTS Page DESCRIPTION... 2 CIRCUIT ANALYSIS... 2 Transmitter... 2 9-volt Regulator... 2 Exciter... 2 40-Watt PA... 2 Antenna

More information

S.R.M Institute of Science and Technology (Deemed University) Department of Electronics & Communication Engineering

S.R.M Institute of Science and Technology (Deemed University) Department of Electronics & Communication Engineering S.R.M Institute of Science and Technology (Deemed University) Department of Electronics & Communication Engineering QUESTION BANK Subject Code : EC211 Subject Name : Communication Engineering Year & Sem

More information

AM and FM MODULATION Lecture 5&6

AM and FM MODULATION Lecture 5&6 AM and FM MODULATION Lecture 5&6 Ir. Muhamad Asvial, MEng., PhD Center for Information and Communication Engineering Research Electrical Engineering Department University of Indonesia Kampus UI Depok,

More information

Single Conversion LF Upconverter Andy Talbot G4JNT Jan 2009

Single Conversion LF Upconverter Andy Talbot G4JNT Jan 2009 Single Conversion LF Upconverter Andy Talbot G4JNT Jan 2009 Mark 2 Version Oct 2010, see Appendix, Page 8 This upconverter is designed to directly translate the output from a soundcard from a PC running

More information

ANALOG COMMUNICATION

ANALOG COMMUNICATION ANALOG COMMUNICATION TRAINING LAB Analog Communication Training Lab consists of six kits, one each for Modulation (ACL-01), Demodulation (ACL-02), Modulation (ACL-03), Demodulation (ACL-04), Noise power

More information

PRINCIPLES OF COMMUNICATION SYSTEMS. Lecture 1- Introduction Elements, Modulation, Demodulation, Frequency Spectrum

PRINCIPLES OF COMMUNICATION SYSTEMS. Lecture 1- Introduction Elements, Modulation, Demodulation, Frequency Spectrum PRINCIPLES OF COMMUNICATION SYSTEMS Lecture 1- Introduction Elements, Modulation, Demodulation, Frequency Spectrum Topic covered Introduction to subject Elements of Communication system Modulation General

More information

Radio Frequency Electronics (RFE)

Radio Frequency Electronics (RFE) Radio Frequency Electronics (RFE) by Prof. Dr.rer.nat. Dr.h.c. Manfred Thumm 5th Edition: 2011 Forschungszentrum Karlsruhe in der Helmholtz - Gemeinschaft Universität Karlsruhe (TH) Research University

More information