Schedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK

Transcription

1 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 Unit Boulton Road Stevenage Hertfordshire SG1 4QX ontact: Mr G J Wilson Tel: +44 (0) Fax: +44 (0) enquiries@mqs.co.uk Website: Laboratory locations: alibration performed by the Organisations at the locations specified below s covered by the organisation and their relevant activities details Activity code Address Unit Boulton Road Stevenage Hertfordshire SG1 4QX Local contact Mr G J Wilson Dimensional A Address 37 Western Parkway Business entre Lower Ballymount Road Dublin 12 IRELAND Local contact Mr P Roche Tel No: +353 [ 0 ] Dimensional B Address 23 Brindley Road Bayton Road Ind Estate Exhall oventry West Midlands V7 9EP Local contact Mr G J Wilson Dimensional & Torque Electrical Site activities performed away from the locations listed above: details Activity code At customers premises Local contact Mr G J Wilson Dimensional D Assessment Manager: ST Page 1 of 13

2 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 alibration performed by the Organisation at the locations specified DETAIL OF AREDITATION alibration and apability (M) RANGE IN MILLIMETRES AND UNERTAINTY IN MIROMETRES ode LENGTH NOTES Gauge blocks Inch (Steel, eramic and tungsten carbide) As BS 4311:Part Inch to 0.4 inch 0.4 Inch to 1 inch lass (see Notes) lass uncertainties apply to the measurement of steel, ceramic and tungsten 2 inch 3 inch 4 inch inch carbide gauges by comparison with grade K standards of length of a similar material. lass Millimetre (Steel, eramic and tungsten carbide) As BS EN ISO 3650: 1999 uncertainties apply to grade 0, 1 and 2 gauges to BS EN ISO 3650:1999 and BS 4311:Part 1:2007 Thread measuring cylinders Precision pin gauges (parallel) Plain plug gauges (parallel) Plain plug gauges (parallel) Plain plug gauges (taper) including check plugs Taper up to 1 in 8 on diameter 0.5 to to 25 30, 40, 50 60, 70, 75 80, 90, As BS 5590:1978 and specials 0.1 to 5.0 diameter 0.1 to 10 diameter 1 to 50 diameter The uncertainty quoted is for the departure from flatness, straightness, parallelism or squareness, i.e. the distance separating the parallel planes which just enclose the surface under consideration. B & B & A Single & multi-start, symmetrical thread forms only. B & 1 to 50 diameter 100 to to to to 50 diameter 100 to on diameter Functional test of size using check plugs. 4. alibration may also be given in lbf.ft and lbf.in 5. Brown & Sharpe PMI Ltd products only. A A B & Tapers above 1 in 8 5 to 50 diameter 5.0 on diameter All linear calibrations may be given in inch units. 100 to Features and associated parts of these gauges / fixtures can be measured to the uncertainties given for equivalent items listed in this schedule. B & Assessment Manager: ST Page 2 of 13

3 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 alibration performed by the Organisation at the locations specified alibration and apability (M) ode RANGE IN MILLIMETRES AND UNERTAINTY IN MIROMETRES LENGTH (cont d) Plain ring gauges (parallel) and setting standards Plain ring gauges (parallel) and setting standards Plain ring gauges (taper) 1 to 10 diameter 10 to to to to to 10 diameter 10 to to to NOTES continued 8. Simple height gauges - vernier, dial and digital instruments designed only for measuring distances parallel to the beam. 10. Single start, symmetrical thread forms only. A & B Taper up to 1 in 8 on diameter 2 to 5 diameter 5 to to on diameter Functional test of size using setting plugs calibrated with a M of 2.5 µm B & Tapers above 1 in 8 on diameter 5 to 50 diameter 100 to on diameter B & Length gauges, flat and spherical ended Length gauges, flat and spherical ended 25 to (8.0 x length in m) A 25 to (8.0 x length in m) B & Plain gap gauges (parallel) 0.5 to to to B & Parallels As BS 906: to 50 x 100 x 400 Vee blocks As BS 3731: to 150 diameter, vee capacity 1.5 to 5.0 B & 1.5 to 5.0 B & Screw plug gauges (parallel) including check and setting plugs See Note 2 1 to to to on pitch diameter 5.0 on pitch diameter 8.0 on pitch diameter 1.5 on pitch 5.0 minutes of arc on flank angle A & B & Assessment Manager: ST Page 3 of 13

4 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 alibration performed by the Organisation at the locations specified alibration and apability (M) ode RANGE IN MILLIMETRES AND UNERTAINTY IN MIROMETRES LENGTH (cont d) Screw plug gauges (taper) including check plugs but excluding API gauges See Note 10 5 to 100 diameter 5.0 on pitch diameter Screw ring gauges (parallel) See Note 2 1 to to to to 250 See note on pitch diameter 6.0 on pitch diameter 10.0 on pitch diameter 1.5 on pitch 5.0 minutes of arc on flank angle 1 to 12 See note 3 B 5 to on pitch diameter Screw ring gauges (taper) - Ground Threads only and excluding API gauges See Note 10 6 to 75 diameter 75 to 150 diameter 5.0 on 7.0 pitch diameter Screw thread adjustable caliper gauges (parallel) See Note 6 1 to 100 diameter See note 11 Receiver, position and profile gauges, jigs and fixtures 0 to 1000 x 750 x (10 x length in m) See note 7 Orifice Plates BS EN ISO : (6.0 x length in m) ANGLE Squares Blade type As BS 939: to to to On 5.0 squareness 8.0 See Note 1 B & ylindrical As BS 939: to to On 4.0 squareness See Note 1 Assessment Manager: ST Page 4 of 13

5 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 alibration performed by the Organisation at the locations specified alibration and apability (M) ode RANGE IN MILLIMETRES AND UNERTAINTY IN MIROMETRES ANGLE (cont d) Angle plates and box angle plates As BS 5535: to 600 Squareness (1.0 per 100 mm) Parallelism (1.0 per 100 mm) See Note 1 B & Bevel protractors As BS 1685: to minutes of arc B & Sine bars As BS 3064: to 300 Sine tables As BS 3064: to 500 FORM (10 x length in m) 3.0 Seconds of arc (10 x length in m) 3.0 Seconds of arc Surface plates Granite ast iron As BS 817:2008 and above 160 x 100 to 4000 x (0.80 x diagonal in m) See Note 1 B & & D Straightedges ast iron Steel Granite As BS 5204:Part 1: to 4000 As BS 5204:Part 2: to (2.0 x length in m) See Note 1 Straightedges ast iron Steel Granite As BS 5204:Part 1: to 1000 As BS 5204:Part 2: to (2.0 x length in m) See Note 1 B Steel balls 1 to 50 diameter 0.80 on diameter Roundness External Internal As BS to 350 diameter 3 to on radius Surface texture (excluding measurement standards and roughness comparison specimens) As BS 1134:Part 1:1988 Ra 0.02 µm to 80 µm 10 % of measured value Assessment Manager: ST Page 5 of 13

6 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 alibration performed by the Organisation at the locations specified alibration and apability (M) ode MEASURING INSTRUMENTS AND MAHINES RANGE IN MILLIMETRES AND UNERTAINTY IN MIROMETRES Micrometers External Internal Depth As BS 870: to to 150 As BS 959: to 900 As BS 6468: to 300 Heads 2.0 between any two points. Setting and extension rods (8.0 x length in m) A & B B & A & B & Indicating micrometers 0 to 100 Indicators 0.50 Overall performance 1.5 A & B & Bore micrometers (three- 1 to point) 5 to B & 100 to Bench micrometer NPL MOY/SMI 22 0 to 100 Overall performance 2.0 ombination sets 0 to 360 (Protractor) 0 to 500 (Rule) 30 minutes of arc (10 x length in m) alliper gauges including vernier, dial and digital types As BS EN ISO : to 2000 Length measurement error, E Overall performance 10 + (20 x length in m) Height gauges - (Simple) including vernier, dial and digital types (See note 8 and note 9) As BS EN ISO 13225:2012 (0 to 1000) Length measurement error (E): (10 x length in m) B & Vernier gauges aliper Height Depth including dial and digital type As BS 887: to 300 As BS 1643:2008 withdrawn 0 to 300 As BS 6365: to 300 Overall performance 10 + (30 x length in m) A Assessment Manager: ST Page 6 of 13

7 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 alibration performed by the Organisation at the locations specified alibration and apability (M) ode MEASURING INSTRUMENTS AND MAHINES (cont d) RANGE IN MILLIMETRES AND UNERTAINTY IN MIROMETRES Vernier gauges aliper Height Depth including dial and digital type As BS 887: to to 2000 As BS 1643:2008 withdrawn 0 to 1000 As BS 6365: to 600 Overall performance 10 + (30 x length in m) B & B & B & Dial gauges and dial test indicators As BS 907:2008 and BS 2795: to A & B & omparators (external) As BS 1054: to magnifications 1.0 % of range Minimum 0.10 Displacement transducers 0 to (4.0 x length in m) B & Thread diameter measuring NPL Schedules MOY/SMI/9 0 to 300 capacity Overall performance 1.5 Plain taper diameter measuring NPL MOY/SMI/48 0 to 100 Overall performance on diameter 1.5 Toolmakers Microscopes As MOY/SMI/ Linear 0 to 150 x 150 Angular 0 to minutes of arc & Universal microscopes Linear 0 to 300 x 300 Angular 0 to minutes of arc Air gauging units (See Note 5) 0 to 5000 magnifications 0.50 % of range Radius Gauges 0 to 300 mm 10 Feeler Gauges As BS 957: to A & B & Internal and External aliper Gauges 0 to A & B & linometers 0 to 360 degrees 10 seconds of arc Electronic indicating levels 0 to 20 minutes of arc 1.0 % of range Minimum 0.50 seconds of arc B & Assessment Manager: ST Page 7 of 13

8 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 alibration performed by the Organisation at the locations specified alibration and apability (M) ode MEASURING INSTRUMENTS AND MAHINES (cont d) RANGE IN MILLIMETRES AND UNERTAINTY IN MIROMETRES Spirit levels As BS 3509:1962 and BS 958: seconds of arc to 60 minutes of arc nominal sensitivity Mean sensitivity: 10 % of nominal Minimum 0.50 seconds of arc B & Micrometer heads As BS 1734: to Height setting micrometer 300 Heads 1.20 Stepped column 2.0 Overall performance 2.5 B & Riser blocks for above Precision scales (linear) 0 to (3.0 x length in m) Steel rules As BS 4372: to to (10 x length in m) 10 + (10 x length in m) Dividing heads 100 to 450 capacity Overall angular & D Rotary tables 100 to 450 performance & D Inclinable rotary tables 100 to seconds of arc & D Profile projectors 10 to 100 magnifications 125 at the screen B & & D 2.5 linear scales 1.5 minutes of arc Height gauges (omplex) (See note 9) As BS EN ISO 13225: to 1 m Length measurement error (E): (5.0 x length in m) Length measurement error (B): (5.0 x length in m) & D Electronic microprocessor controlled height gauges 0 to 1 m (5.0 x length in m) B & & D Horizontal & vertical measuring machines Evaluation of electrical contact unit for internal measurement 0 to 1 m (1.0 x length in m) Overall performance 1.0 on diameter. & D & D Assessment Manager: ST Page 8 of 13

9 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 alibration performed by the Organisation at the locations specified alibration and apability (M) ode TORQUE Hand Torque Tools As BS EN ISO 6789: to 1000 Nm 1.6 % of maximum reading (see note 4) ELETRIAL D Voltage Generation 0 V to 300 mv 17 ppm V 300 mv to 3 V 11 ppm V 3 V to 30 V 10 ppm mv 30 V to 300 V 13 ppm mv 300 V to 1000 V 16 ppm mv 0 V to 100 mv 15 ppm V 100 mv to 1 V 8.0 ppm V 1 V to 10 V 4.0 ppm + 12 µv 10 V to 100 V 5.0 ppm µv 100 V to 1000 V 7.0 ppm µv D urrent Generation 0 A to 300 A 60 ppm + 24 na 300 A to 3 ma 30 ppm A 3 ma to 30 ma 36 ppm A 30 ma to 300 ma 43 ppm A 300 ma to 1 A 1 A to 3 A 3 A to 11 A 11 A to 20 A 110 ppm ma 110 ppm ma 110 ppm ma 400 ppm ma 20 A to 100 A 0.15 % For the calibration of 100 A to 550 A 0.18 % clampmeters only 10 A to 100 A 120 ppm na 100 A to 1 ma 30 ppm A 1 ma to 10 ma 37 ppm A 10 ma to 100 ma 30 ppm A 100 ma to 2 A 78 ppm + 47 A Assessment Manager: ST Page 9 of 13

10 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 alibration performed by the Organisation at the locations specified alibration and apability (M) ode A Voltage Generation 10 mv to 300 mv 45 Hz to 1 khz % + 10 V 1 khz to 10 khz % + 10 V 300 mv to 3 V 45 Hz to 1 khz % + 70 V 1 khz to 10 khz % + 70 V 3 V to 30 V 45 Hz to 1 khz % mv 1 khz to 10 khz % mv 30 V to 300 V 45 Hz to 1 khz % mv 1 khz to 10 khz % mv 300 V to 1000 V 45 Hz to 1 khz % + 17 mv 1 khz to 10 khz % + 17 mv 10 mv to 100 mv 20 Hz to 1 khz % µv 1 khz to 10 khz % µv A urrent 100 mv to 1 V 20 Hz to 1 khz % + 12 µv 1 khz to 10 khz % + 12 µv 1 V to 10 V 20 Hz to 1 khz % µv 1 khz to 10 khz % µv 10 V to 100 V 20 Hz to 1 khz % mv 1 khz to 10 khz % mv 100 V to 1000 V 55 Hz to 1 khz % + 24 mv 1 khz to 10 khz % + 24 mv Generation 10 A to 300 A 45 Hz to 1 khz 0.10 % A 1 khz to 5 khz 0.11 % A 300 A to 3 ma 45 Hz to 1 khz % A 1 khz to 5 khz % A Assessment Manager: ST Page 10 of 13

11 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 alibration performed by the Organisation at the locations specified alibration and apability (M) ode A urrent (ontinued) 3 ma to 30 ma Generation 45 Hz to 1 khz % A 1 khz to 5 khz % A 30 ma to 300 ma 45 Hz to 1 khz % + 24 A 1 khz to 5 khz % + 58 A 300 ma to 1 A 45 Hz to 1 khz % ma 1 khz to 5 khz 0.15 % ma 1 A to 3 A 45 Hz to 1 khz % ma 1 khz to 5 khz 0.15 % ma 3 A to 11 A 45 Hz to 1 khz % ma 1 khz to 5 khz 0.85 % ma 11 A to 20 A 45 Hz to 1 khz % ma 1 khz to 5 khz 0.80 % ma 20 A to 100 A 45 Hz to 1 khz 0.25 % For the calibration of clampmeters only 100 A to 550 A 45 Hz to 65 Hz 65 Hz to 500 Hz 0.30 % 0.50 % For the calibration of clampmeters only A urrent 10 A to 100 A 55 Hz to 1 khz % A 1 khz to 5 khz 0.11 % A 100 A to 1 ma 55 Hz to 1 khz % A 1 khz to 5 khz % A 1 ma to 10 ma 55 Hz to 1 khz % A 1 khz to 5 khz % A 10 ma to 100 ma 55 Hz to 1 khz % + 12 A 1 khz to 5 khz % + 12 A 100 ma to 2 A 55 Hz to 1 khz % ma 1 khz to 5 khz 0.20 % ma Assessment Manager: ST Page 11 of 13

12 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 alibration performed by the Organisation at the locations specified alibration and apability (M) ode D Resistance Generation ppm + 12 m ppm m ppm m ppm m ppm m 1 k 14 ppm m 3 k 22 ppm + 24 m 10 k 17 ppm + 26 m 30 k 15 ppm k 12 ppm k 19 ppm M 70 ppm M 80 ppm M 210 ppm M 230 ppm k 100 M 350 ppm k 300 M 0.22 % k 1000 M 0.31 % k D Resistance 0 to 1 16 ppm to ppm + 26 µ 10 to ppm + 42 µ 100 to 1 k 11 ppm µ 1 k to 10 k 7.0 ppm m 10 k to 100 k 11 ppm + 35 m 100 k to 1 M 26 ppm m 1 M to 10 M 42 ppm m 10 M to 100 M 150 ppm M to 1 G 400 ppm k Assessment Manager: ST Page 12 of 13

13 2 Pine Trees, hertsey Lane, Staines-upon-Thames, TW18 3HR, UK ISO/IE 17025:2005 alibration performed by the Organisation at the locations specified alibration and apability (M) ode Temperature indicators, calibration by electrical simulation Base metal thermocouple to excluding cold junction compensation Noble metal thermocouple to excluding cold junction compensation old junction compensation At ambient temperature of Resistance sensors to to Frequency 1 Hz to 1.35 GHz 4.0 in 10 8 Time Interval 0.05 s to 60 min s Tachometers (Optical) 100 rpm to rpm 2.0 rpm END Assessment Manager: ST Page 13 of 13