Cleveland State University MCE441: Intr. Linear Control Systems. Lecture 12: Frequency Response Concepts Bode Diagrams. Prof.

Size: px
Start display at page:

Download "Cleveland State University MCE441: Intr. Linear Control Systems. Lecture 12: Frequency Response Concepts Bode Diagrams. Prof."

Transcription

1 Cleveland State University MCE441: Intr. Linear Control Systems Lecture 12: Concepts Bode Diagrams Prof. Richter 1 / 2

2 Control systems are affected by signals which are often unpredictable: noise, disturbances, reference inputs. Frequency content can be a better way to characterize these signals, as opposed to time description. The frequency content of any signal can be obtained analytically or experimentally using Fourier analysis. Nyquist, Bode and Nichols introduced frequency response methods in dynamics and control in the 193 s and 4 s. The first step is to study how linear systems (transfer functions) are affected by signals of various frequencies. 2 / 2

3 Frequency Response of a Linear System Dynamic system response is selective to frequency: amplitude changes and phase shifts. Think of the TF as a frequency-dependent device which alters the amplitude and phase of the incoming sinewave. The frequency response of a system is a description of the amplitude and phase variations as a function of frequency We ll learn how to construct frequency response diagrams. It can be shown that for t : Amplification Ratio= G(jw) Phase Shift= G(jw) 3 / 2

4 Frequency Reponse and the Transfer X G(jw) X X sin(wt) G(jw) X sin(wt + G(jw)) G(s) 4 / 2

5 Demo: Beam with Piezoelectric Actuators Frequency Reponse and the Transfer We use the WinCon real-time control interface to connect to an experiment in the lab over the internet. The actuator will be excited with a sinewave at 9 Hz. We record the amplitude of tip vibrations as measured by an optical sensor. We find the experimental values of the amplitude ratio and the phase shift. Then we compare it to the values obtained using the transfer function. 5 / 2

6 In-Class Demo: Calculation Frequency Reponse and the Transfer G(s): Input Amplitude: Input Frequency (rad/s): Meas. Output Amplitude: Amplitude ratio: Meas. Time Shift: Phase Shift (rad): G(jw) : G(jw): 6 / 2

7 Handling Non-Sinusoidal Signals Frequency Reponse and the Transfer Two key facts provide a rationale for using freq. response as an analysis tool for more general signals: Linear systems satisfy superposition: The response to a weighted sum of inputs is the weighted sum of the responses to the individual inputs. Most signals (even some discontinuous and non-smooth ones) admit a Fourier series expansion. That is, an arbitrary signal may be decomposed as a weighted sum of sinewaves, each one having its own amplitude and phase. Therefore: We can characterize the reponse of a system to an arbitrary input by resolving the input into a sum of sinewaves and determining the contribution of each frequency to the overall reponse. 7 / 2

8 Linear Systems and Superposition Frequency Reponse and the Transfer u 1 (t) u 2 (t) u 3 (t) u 4 (t) u 5 (t) G(s) y(t) u 1 (t) u 2 (t) u 3 (t) u 4 (t) u 5 (t) G(s) G(s) G(s) G(s) G(s) y(t) 8 / 2

9 Resolving a Signal into Frequencies value Time History time power Spectral Analysis Frequency Content frequency 9 / 2

10 : Triangle Wave Resolving a Signal into Frequencies We run a Matlab script to display succesive approximations to the triangle wave using sinewaves. %fourier_triangle MAX=1; %plot the original wave x1=[:.1:.5]; x2=[.5:.1:1.5]; x3=[1.5:.1:2]; plot(x1,2*x1, k,x2,1-2*(x2-.5), k,x3,-1+2*(x3-1.5), k ); %calculate and plot the fourier with up to MAX terms hold on for stop=1:max, j=1; for x=:.5:2, sum=; for i=1:2:stop, sum=sum+(-1)^((i-1)/2)*sin(i*pi*x)/i^2; end fx(j)=8*sum/pi^2; j=j+1; end plot([:.5:2],fx, r ) pause end 1 / 2

11 Frequency Reponse The amplification ratio is called Magnitude The phase shift is called Phase A Bode plot is a set of two charts: magnitude vs. frequency and phase vs. frequency. Magnitude peaks can be quite large. For this reason, and to facilitate hand-sketching, the magnitude is charted in decibels (db) mag (db) = 2 log( G(jw) ) Phase is charted in degrees. A log scale is used for frequency. Phase and dbs are charted using a regular linear scale. 11 / 2

12 dbs, decades, octaves, attenuation... Frequency Reponse Some freq. response terms: (a lot more later) Converting x to db: 2logx Decade: A frequency increase by a factor of 1 (one logarithmic unit) Octave: A frequency increase by a factor of 8. Attenuation: refers to the decrease in magnitude with frequency. Measured in db. Amplification: refers to the increase in magnitude with frequency. Measured in db. 12 / 2

13 A Typical Bode Plot Frequency Reponse Phase (deg) Magnitude (db) low freq. gain bandwidth mag. crossover freq. mag. peak 225 phase crossover freq Frequency (rad/sec) 13 / 2

14 Key idea: phase angles and log magnitudes of individual factors are added together. Arrange G(s) into normalized pole-zero factors and use templates for each. Then just add the graphs. Our template: G(s) = Ks k (τ z1s+1)(τ z2 s 1 )... (τ p1 s+1)(τ p2 s+1)... w 2 p1 s 2 +2ζ p1 w p1 s+w 2 p1 s 2 +2ζ z1 w z1 s+w 2 z1 w 2 z1 Only one 2nd order zero pair and one 2nd order pole pair is shown, but there could be more. The exponent k can be positive, zero or negative. 14 / 2

15 mag (db) 1 phase 45 τ p Real Pole: 1 τ p s+1.1 τ p 1 τ p 9-45 /dec mag (db) phase 1 τ p w p Cplx Poles: w(rad/s) -2 db/dec w(rad/s) w(rad/s) -4 db/dec w 2 p s 2 +2ζ p w p s+w 2 p.1w p w p 1w p w(rad/s) mag (db) 1 τ z 2 db/dec w(rad/s) Real Zero: (τ z s + 1) phase /dec.1 τ z mag (db) 1 τ z 1 τ z w(rad/s) Cplx Zeros: s2 +2ζ z w z s+w 2 z w 2 z phase w z 4 db/dec w(rad/s) mag (db) phase 1 2k db/dec w(rad/s) k9 w(rad/s) mag (db) phase Mult. root at s = : s k 2 log K Gain: K w(rad/s) /dec /dec w(rad/s).1w z w z 1w z w(rad/s) 15 / 2

16 Finishing Touches For second-order poles/zeros, find the resonant peak according to damping ratio: M r = max G(jw) = 1 2ζ 1 ζ 2 For first order poles and zeros, account for a ±3 db of attenuation/amplification at crossover. If the crossover frequencies of distinct factors are close together, it is hard to predict the actual attenuation or size of the resonant peak without resorting to finer calculations (hand/matlab). 16 / 2

17 Normalized Second Order Freq. Resp. 17 / 2

18 Sketch the Bode plot for G(s) = 1(s+3) s(s+2)(s 2 +s+2) 18 / 2

19 19 / 2

20 2 / 2

EEL2216 Control Theory CT2: Frequency Response Analysis

EEL2216 Control Theory CT2: Frequency Response Analysis EEL2216 Control Theory CT2: Frequency Response Analysis 1. Objectives (i) To analyse the frequency response of a system using Bode plot. (ii) To design a suitable controller to meet frequency domain and

More information

SECTION 7: FREQUENCY DOMAIN ANALYSIS. MAE 3401 Modeling and Simulation

SECTION 7: FREQUENCY DOMAIN ANALYSIS. MAE 3401 Modeling and Simulation SECTION 7: FREQUENCY DOMAIN ANALYSIS MAE 3401 Modeling and Simulation 2 Response to Sinusoidal Inputs Frequency Domain Analysis Introduction 3 We ve looked at system impulse and step responses Also interested

More information

Lecture 9. Lab 16 System Identification (2 nd or 2 sessions) Lab 17 Proportional Control

Lecture 9. Lab 16 System Identification (2 nd or 2 sessions) Lab 17 Proportional Control 246 Lecture 9 Coming week labs: Lab 16 System Identification (2 nd or 2 sessions) Lab 17 Proportional Control Today: Systems topics System identification (ala ME4232) Time domain Frequency domain Proportional

More information

CHAPTER 6 Frequency Response, Bode. Plots, and Resonance

CHAPTER 6 Frequency Response, Bode. Plots, and Resonance CHAPTER 6 Frequency Response, Bode Plots, and Resonance CHAPTER 6 Frequency Response, Bode Plots, and Resonance 1. State the fundamental concepts of Fourier analysis. 2. Determine the output of a filter

More information

Compensator Design using Bode Plots

Compensator Design using Bode Plots Gain Compensation Compensator Design using Bode Plots Nichols charts are useful since it shows directly what you are trying to do when designing a compensator: you are trying to keep away from -1 to limit

More information

Frequency Response Analysis and Design Tutorial

Frequency Response Analysis and Design Tutorial 1 of 13 1/11/2011 5:43 PM Frequency Response Analysis and Design Tutorial I. Bode plots [ Gain and phase margin Bandwidth frequency Closed loop response ] II. The Nyquist diagram [ Closed loop stability

More information

Bode and Log Magnitude Plots

Bode and Log Magnitude Plots Bode and Log Magnitude Plots Bode Magnitude and Phase Plots System Gain and Phase Margins & Bandwidths Polar Plot and Bode Diagrams Transfer Function from Bode Plots Bode Plots of Open Loop and Closed

More information

Välkomna till TSRT15 Reglerteknik Föreläsning 5. Summary of lecture 4 Frequency response Bode plot

Välkomna till TSRT15 Reglerteknik Föreläsning 5. Summary of lecture 4 Frequency response Bode plot Välkomna till TSRT15 Reglerteknik Föreläsning 5 Summary of lecture 4 Frequency response Bode plot Summary of last lecture 2 Given a pole polynomial with a varying parameter P(s)+KQ(s)=0 We draw the location

More information

EES42042 Fundamental of Control Systems Bode Plots

EES42042 Fundamental of Control Systems Bode Plots EES42042 Fundamental of Control Systems Bode Plots DR. Ir. Wahidin Wahab M.Sc. Ir. Aries Subiantoro M.Sc. 2 Bode Plots Plot of db Gain and phase vs frequency It is assumed you know how to construct Bode

More information

MTE 360 Automatic Control Systems University of Waterloo, Department of Mechanical & Mechatronics Engineering

MTE 360 Automatic Control Systems University of Waterloo, Department of Mechanical & Mechatronics Engineering MTE 36 Automatic Control Systems University of Waterloo, Department of Mechanical & Mechatronics Engineering Laboratory #1: Introduction to Control Engineering In this laboratory, you will become familiar

More information

Bode Plot for Controller Design

Bode Plot for Controller Design Bode Plot for Controller Design Dr. Bishakh Bhattacharya Professor, Department of Mechanical Engineering IIT Kanpur Joint Initiative of IITs and IISc - Funded by This Lecture Contains Bode Plot for Controller

More information

(A) Based on the second-order FRF provided, determine appropriate values for ω n, ζ, and K. ω n =500 rad/s; ζ=0.1; K=0.

(A) Based on the second-order FRF provided, determine appropriate values for ω n, ζ, and K. ω n =500 rad/s; ζ=0.1; K=0. ME35 Homework # Due: 1/1/1 Problem #1 (3%) A co-worker brings you an accelerometer spec sheet with the following frequency response function (FRF):. s G accelerometer = [volt +.1 jω.1 ω m ] (A) Based on

More information

Boise State University Department of Electrical and Computer Engineering ECE 212L Circuit Analysis and Design Lab

Boise State University Department of Electrical and Computer Engineering ECE 212L Circuit Analysis and Design Lab Objectives Boise State University Department of Electrical and Computer Engineering ECE L Circuit Analysis and Design Lab Experiment #0: Frequency esponse Measurements The objectives of this laboratory

More information

Introduction to Signals and Systems Lecture #9 - Frequency Response. Guillaume Drion Academic year

Introduction to Signals and Systems Lecture #9 - Frequency Response. Guillaume Drion Academic year Introduction to Signals and Systems Lecture #9 - Frequency Response Guillaume Drion Academic year 2017-2018 1 Transmission of complex exponentials through LTI systems Continuous case: LTI system where

More information

ME451: Control Systems. Course roadmap

ME451: Control Systems. Course roadmap ME451: Control Systems Lecture 20 Root locus: Lead compensator design Dr. Jongeun Choi Department of Mechanical Engineering Michigan State University Fall 2008 1 Modeling Course roadmap Analysis Design

More information

Modeling and Analysis of Systems Lecture #9 - Frequency Response. Guillaume Drion Academic year

Modeling and Analysis of Systems Lecture #9 - Frequency Response. Guillaume Drion Academic year Modeling and Analysis of Systems Lecture #9 - Frequency Response Guillaume Drion Academic year 2015-2016 1 Outline Frequency response of LTI systems Bode plots Bandwidth and time-constant 1st order and

More information

, answer the next six questions.

, answer the next six questions. Frequency Response Problems Conceptual Questions 1) T/F Given f(t) = A cos (ωt + θ): The amplitude of the output in sinusoidal steady-state increases as K increases and decreases as ω increases. 2) T/F

More information

Response spectrum Time history Power Spectral Density, PSD

Response spectrum Time history Power Spectral Density, PSD A description is given of one way to implement an earthquake test where the test severities are specified by time histories. The test is done by using a biaxial computer aided servohydraulic test rig.

More information

and using the step routine on the closed loop system shows the step response to be less than the maximum allowed 20%.

and using the step routine on the closed loop system shows the step response to be less than the maximum allowed 20%. Phase (deg); Magnitude (db) 385 Bode Diagrams 8 Gm = Inf, Pm=59.479 deg. (at 62.445 rad/sec) 6 4 2-2 -4-6 -8-1 -12-14 -16-18 1-1 1 1 1 1 2 1 3 and using the step routine on the closed loop system shows

More information

Engineering Discovery

Engineering Discovery Modeling, Computing, & Measurement: Measurement Systems # 4 Dr. Kevin Craig Professor of Mechanical Engineering Rensselaer Polytechnic Institute 1 Frequency Response and Filters When you hear music and

More information

sin(wt) y(t) Exciter Vibrating armature ENME599 1

sin(wt) y(t) Exciter Vibrating armature ENME599 1 ENME599 1 LAB #3: Kinematic Excitation (Forced Vibration) of a SDOF system Students must read the laboratory instruction manual prior to the lab session. The lab report must be submitted in the beginning

More information

ECE 3155 Experiment I AC Circuits and Bode Plots Rev. lpt jan 2013

ECE 3155 Experiment I AC Circuits and Bode Plots Rev. lpt jan 2013 Signature Name (print, please) Lab section # Lab partner s name (if any) Date(s) lab was performed ECE 3155 Experiment I AC Circuits and Bode Plots Rev. lpt jan 2013 In this lab we will demonstrate basic

More information

Andrea Zanchettin Automatic Control 1 AUTOMATIC CONTROL. Andrea M. Zanchettin, PhD Winter Semester, Linear control systems design Part 1

Andrea Zanchettin Automatic Control 1 AUTOMATIC CONTROL. Andrea M. Zanchettin, PhD Winter Semester, Linear control systems design Part 1 Andrea Zanchettin Automatic Control 1 AUTOMATIC CONTROL Andrea M. Zanchettin, PhD Winter Semester, 2018 Linear control systems design Part 1 Andrea Zanchettin Automatic Control 2 Step responses Assume

More information

Classical Control Design Guidelines & Tools (L10.2) Transfer Functions

Classical Control Design Guidelines & Tools (L10.2) Transfer Functions Classical Control Design Guidelines & Tools (L10.2) Douglas G. MacMartin Summarize frequency domain control design guidelines and approach Dec 4, 2013 D. G. MacMartin CDS 110a, 2013 1 Transfer Functions

More information

EE Experiment 8 Bode Plots of Frequency Response

EE Experiment 8 Bode Plots of Frequency Response EE16:Exp8-1 EE 16 - Experiment 8 Bode Plots of Frequency Response Objectives: To illustrate the relationship between a system frequency response and the frequency response break frequencies, factor powers,

More information

Open Loop Frequency Response

Open Loop Frequency Response TAKE HOME LABS OKLAHOMA STATE UNIVERSITY Open Loop Frequency Response by Carion Pelton 1 OBJECTIVE This experiment will reinforce your understanding of the concept of frequency response. As part of the

More information

(i) Sine sweep (ii) Sine beat (iii) Time history (iv) Continuous sine

(i) Sine sweep (ii) Sine beat (iii) Time history (iv) Continuous sine A description is given of one way to implement an earthquake test where the test severities are specified by the sine-beat method. The test is done by using a biaxial computer aided servohydraulic test

More information

Chapter 5 Frequency-domain design

Chapter 5 Frequency-domain design Chapter 5 Frequency-domain design Control Automático 3º Curso. Ing. Industrial Escuela Técnica Superior de Ingenieros Universidad de Sevilla Outline of the presentation Introduction. Time response analysis

More information

EECS40 RLC Lab guide

EECS40 RLC Lab guide EECS40 RLC Lab guide Introduction Second-Order Circuits Second order circuits have both inductor and capacitor components, which produce one or more resonant frequencies, ω0. In general, a differential

More information

PHYSICS 330 LAB Operational Amplifier Frequency Response

PHYSICS 330 LAB Operational Amplifier Frequency Response PHYSICS 330 LAB Operational Amplifier Frequency Response Objectives: To measure and plot the frequency response of an operational amplifier circuit. History: Operational amplifiers are among the most widely

More information

Core Technology Group Application Note 6 AN-6

Core Technology Group Application Note 6 AN-6 Characterization of an RLC Low pass Filter John F. Iannuzzi Introduction Inductor-capacitor low pass filters are utilized in systems such as audio amplifiers, speaker crossover circuits and switching power

More information

ME 375. HW 7 Solutions. Original Homework Assigned 10/12, Due 10/19.

ME 375. HW 7 Solutions. Original Homework Assigned 10/12, Due 10/19. ME 375. HW 7 Solutions. Original Homework Assigned /2, Due /9. Problem. Palm 8.2 a-b Part (a). T (s) = 5 6s+2 = 5 2 3s+. Here τ = 3 and the multiplicative factor 5/2 shifts the magnitude curve up by 2log5/2

More information

Chapter 5 Window Functions. periodic with a period of N (number of samples). This is observed in table (3.1).

Chapter 5 Window Functions. periodic with a period of N (number of samples). This is observed in table (3.1). Chapter 5 Window Functions 5.1 Introduction As discussed in section (3.7.5), the DTFS assumes that the input waveform is periodic with a period of N (number of samples). This is observed in table (3.1).

More information

Lab 9 Frequency Domain

Lab 9 Frequency Domain Lab 9 Frequency Domain 1 Components Required Resistors Capacitors Function Generator Multimeter Oscilloscope 2 Filter Design Filters are electric components that allow applying different operations to

More information

Structure of Speech. Physical acoustics Time-domain representation Frequency domain representation Sound shaping

Structure of Speech. Physical acoustics Time-domain representation Frequency domain representation Sound shaping Structure of Speech Physical acoustics Time-domain representation Frequency domain representation Sound shaping Speech acoustics Source-Filter Theory Speech Source characteristics Speech Filter characteristics

More information

Lab Assignment 1 Spectrum Analyzers

Lab Assignment 1 Spectrum Analyzers 1 Objectives THE UNIVERSITY OF BRITISH COLUMBIA Department of Electrical and Computer Engineering ELEC 391 Electrical Engineering Design Studio II Lab Assignment 1 Spectrum Analyzers This lab consists

More information

Course Outline. Time vs. Freq. Domain Analysis. Frequency Response. Amme 3500 : System Dynamics & Control. Design via Frequency Response

Course Outline. Time vs. Freq. Domain Analysis. Frequency Response. Amme 3500 : System Dynamics & Control. Design via Frequency Response Course Outline Amme 35 : System Dynamics & Control Design via Frequency Response Week Date Content Assignment Notes Mar Introduction 2 8 Mar Frequency Domain Modelling 3 5 Mar Transient Performance and

More information

CHAPTER 6 INTRODUCTION TO SYSTEM IDENTIFICATION

CHAPTER 6 INTRODUCTION TO SYSTEM IDENTIFICATION CHAPTER 6 INTRODUCTION TO SYSTEM IDENTIFICATION Broadly speaking, system identification is the art and science of using measurements obtained from a system to characterize the system. The characterization

More information

Lab Assignment 1 Spectrum Analyzers

Lab Assignment 1 Spectrum Analyzers THE UNIVERSITY OF BRITISH COLUMBIA Department of Electrical and Computer Engineering ELEC 391 Electrical Engineering Design Studio II Lab Assignment 1 Spectrum Analyzers 1 Objectives This lab consists

More information

Laboratory Experiment #1 Introduction to Spectral Analysis

Laboratory Experiment #1 Introduction to Spectral Analysis J.B.Francis College of Engineering Mechanical Engineering Department 22-403 Laboratory Experiment #1 Introduction to Spectral Analysis Introduction The quantification of electrical energy can be accomplished

More information

ECE317 Homework 7. where

ECE317 Homework 7. where ECE317 Homework 7 Problem 1: Consider a system with loop gain, T(s), given by: where T(s) = 300(1+s)(1+ s 40 ) 1) Determine whether the system is stable by finding the closed loop poles of the system using

More information

Bode Plots. Hamid Roozbahani

Bode Plots. Hamid Roozbahani Bode Plots Hamid Roozbahani A Bode plot is a graph of the transfer function of a linear, time-invariant system versus frequency, plotted with a logfrequency axis, to show the system's frequency response.

More information

Lecture 7:Examples using compensators

Lecture 7:Examples using compensators Lecture :Examples using compensators Venkata Sonti Department of Mechanical Engineering Indian Institute of Science Bangalore, India, This draft: March, 8 Example :Spring Mass Damper with step input Consider

More information

Kent Bertilsson Muhammad Amir Yousaf

Kent Bertilsson Muhammad Amir Yousaf Today s topics Analog System (Rev) Frequency Domain Signals in Frequency domain Frequency analysis of signals and systems Transfer Function Basic elements: R, C, L Filters RC Filters jw method (Complex

More information

3.2 Measuring Frequency Response Of Low-Pass Filter :

3.2 Measuring Frequency Response Of Low-Pass Filter : 2.5 Filter Band-Width : In ideal Band-Pass Filters, the band-width is the frequency range in Hz where the magnitude response is at is maximum (or the attenuation is at its minimum) and constant and equal

More information

BJT & FET Frequency Response

BJT & FET Frequency Response Chapter 4 BJT & FET Spring 2012 4 th Semester Mechatronics SZABIST, Karachi 2 Course Support humera.rafique@szabist.edu.pk Office: 100 Campus (404) Official: ZABdesk Subsidiary: https://sites.google.com/site/zabistmechatronics/home/spring-2012/ecd

More information

CDS 101/110: Lecture 9.1 Frequency DomainLoop Shaping

CDS 101/110: Lecture 9.1 Frequency DomainLoop Shaping CDS /: Lecture 9. Frequency DomainLoop Shaping November 3, 6 Goals: Review Basic Loop Shaping Concepts Work through example(s) Reading: Åström and Murray, Feedback Systems -e, Section.,.-.4,.6 I.e., we

More information

Laboratory 7: Active Filters

Laboratory 7: Active Filters EGR 224L - Spring 208 7. Introduction Laboratory 7: Active Filters During this lab, you are going to use data files produced by two different low-pass filters to examine MATLAB s ability to predict transfer

More information

PYKC 13 Feb 2017 EA2.3 Electronics 2 Lecture 8-1

PYKC 13 Feb 2017 EA2.3 Electronics 2 Lecture 8-1 In this lecture, I will cover amplitude and phase responses of a system in some details. What I will attempt to do is to explain how would one be able to obtain the frequency response from the transfer

More information

Department of Mechanical and Aerospace Engineering. MAE334 - Introduction to Instrumentation and Computers. Final Examination.

Department of Mechanical and Aerospace Engineering. MAE334 - Introduction to Instrumentation and Computers. Final Examination. Name: Number: Department of Mechanical and Aerospace Engineering MAE334 - Introduction to Instrumentation and Computers Final Examination December 12, 2002 Closed Book and Notes 1. Be sure to fill in your

More information

Signals, systems, acoustics and the ear. Week 3. Frequency characterisations of systems & signals

Signals, systems, acoustics and the ear. Week 3. Frequency characterisations of systems & signals Signals, systems, acoustics and the ear Week 3 Frequency characterisations of systems & signals The big idea As long as we know what the system does to sinusoids...... we can predict any output to any

More information

BSNL TTA Question Paper Control Systems Specialization 2007

BSNL TTA Question Paper Control Systems Specialization 2007 BSNL TTA Question Paper Control Systems Specialization 2007 1. An open loop control system has its (a) control action independent of the output or desired quantity (b) controlling action, depending upon

More information

Free vibration of cantilever beam FREE VIBRATION OF CANTILEVER BEAM PROCEDURE

Free vibration of cantilever beam FREE VIBRATION OF CANTILEVER BEAM PROCEDURE FREE VIBRATION OF CANTILEVER BEAM PROCEDURE AIM Determine the damped natural frequency, logarithmic decrement and damping ratio of a given system from the free vibration response Calculate the mass of

More information

Acoustics, signals & systems for audiology. Week 3. Frequency characterisations of systems & signals

Acoustics, signals & systems for audiology. Week 3. Frequency characterisations of systems & signals Acoustics, signals & systems for audiology Week 3 Frequency characterisations of systems & signals The BIG idea: Illustrated 2 Representing systems in terms of what they do to sinusoids: Frequency responses

More information

Feedback (and control) systems

Feedback (and control) systems Feedback (and control) systems Stability and performance Copyright 2007-2008 Stevens Institute of Technology - All rights reserved 22-1/23 Behavior of Under-damped System Y() s s b y 0 M s 2n y0 2 2 2

More information

Exercise 8: Frequency Response

Exercise 8: Frequency Response Exercise 8: Frequency Response Introduction We can find the frequency response of a system by exciting the system with a sinusoidal signal of amplitude A and frequency ω [rad/s] (Note: ω = 2πf) and observing

More information

Developer Techniques Sessions

Developer Techniques Sessions 1 Developer Techniques Sessions Physical Measurements and Signal Processing Control Systems Logging and Networking 2 Abstract This session covers the technologies and configuration of a physical measurement

More information

EE422G Solution to Homework #8

EE422G Solution to Homework #8 EE4G Solution to Homework #8. MATLAB >> H = tf([ 4],[ 6 6]); >> H = tf([ ],[ - 5 5 4]); >> step(h).7 Step Response.6.5 Amplitude.4... 4 5 6 >> step(h) Time (sec).5 Step Response.5 Amplitude.5.5.5..5..5..5.4.45

More information

ME 375 System Modeling and Analysis

ME 375 System Modeling and Analysis ME 375 System Modeling and Analysis G(s) H(s) Section 9 Block Diagrams and Feedback Control Spring 2009 School of Mechanical Engineering Douglas E. Adams Associate Professor 9.1 Key Points to Remember

More information

Bode plot, named after Hendrik Wade Bode, is usually a combination of a Bode magnitude plot and Bode phase plot:

Bode plot, named after Hendrik Wade Bode, is usually a combination of a Bode magnitude plot and Bode phase plot: Bode plot From Wikipedia, the free encyclopedia A The Bode plot for a first-order (one-pole) lowpass filter Bode plot, named after Hendrik Wade Bode, is usually a combination of a Bode magnitude plot and

More information

2.161 Signal Processing: Continuous and Discrete

2.161 Signal Processing: Continuous and Discrete MIT OpenCourseWare http://ocw.mit.edu 2.6 Signal Processing: Continuous and Discrete Fall 28 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms. MASSACHUSETTS

More information

CDS 101/110a: Lecture 8-1 Frequency Domain Design

CDS 101/110a: Lecture 8-1 Frequency Domain Design CDS 11/11a: Lecture 8-1 Frequency Domain Design Richard M. Murray 17 November 28 Goals: Describe canonical control design problem and standard performance measures Show how to use loop shaping to achieve

More information

ECE 203 LAB 2 PRACTICAL FILTER DESIGN & IMPLEMENTATION

ECE 203 LAB 2 PRACTICAL FILTER DESIGN & IMPLEMENTATION Version 1. 1 of 7 ECE 03 LAB PRACTICAL FILTER DESIGN & IMPLEMENTATION BEFORE YOU BEGIN PREREQUISITE LABS ECE 01 Labs ECE 0 Advanced MATLAB ECE 03 MATLAB Signals & Systems EXPECTED KNOWLEDGE Understanding

More information

Application Note #2442

Application Note #2442 Application Note #2442 Tuning with PL and PID Most closed-loop servo systems are able to achieve satisfactory tuning with the basic Proportional, Integral, and Derivative (PID) tuning parameters. However,

More information

Acoustics, signals & systems for audiology. Week 4. Signals through Systems

Acoustics, signals & systems for audiology. Week 4. Signals through Systems Acoustics, signals & systems for audiology Week 4 Signals through Systems Crucial ideas Any signal can be constructed as a sum of sine waves In a linear time-invariant (LTI) system, the response to a sinusoid

More information

EC CONTROL SYSTEMS ENGINEERING

EC CONTROL SYSTEMS ENGINEERING 1 YEAR / SEM: II / IV EC 1256. CONTROL SYSTEMS ENGINEERING UNIT I CONTROL SYSTEM MODELING PART-A 1. Define open loop and closed loop systems. 2. Define signal flow graph. 3. List the force-voltage analogous

More information

Build Your Own Bose WaveRadio Bass Preamp Active Filter Design

Build Your Own Bose WaveRadio Bass Preamp Active Filter Design EE230 Filter Laboratory Build Your Own Bose WaveRadio Bass Preamp Active Filter Design Objectives 1) Design an active filter on paper to meet a particular specification 2) Verify your design using Spice

More information

OPERATIONAL AMPLIFIERS and FEEDBACK

OPERATIONAL AMPLIFIERS and FEEDBACK Lab Notes A. La Rosa OPERATIONAL AMPLIFIERS and FEEDBACK 1. THE ROLE OF OPERATIONAL AMPLIFIERS A typical digital data acquisition system uses a transducer (sensor) to convert a physical property measurement

More information

Rotary Motion Servo Plant: SRV02. Rotary Experiment #03: Speed Control. SRV02 Speed Control using QuaRC. Student Manual

Rotary Motion Servo Plant: SRV02. Rotary Experiment #03: Speed Control. SRV02 Speed Control using QuaRC. Student Manual Rotary Motion Servo Plant: SRV02 Rotary Experiment #03: Speed Control SRV02 Speed Control using QuaRC Student Manual Table of Contents 1. INTRODUCTION...1 2. PREREQUISITES...1 3. OVERVIEW OF FILES...2

More information

ME 365 EXPERIMENT 8 FREQUENCY ANALYSIS

ME 365 EXPERIMENT 8 FREQUENCY ANALYSIS ME 365 EXPERIMENT 8 FREQUENCY ANALYSIS Objectives: There are two goals in this laboratory exercise. The first is to reinforce the Fourier series analysis you have done in the lecture portion of this course.

More information

Lab 11. Speed Control of a D.C. motor. Motor Characterization

Lab 11. Speed Control of a D.C. motor. Motor Characterization Lab 11. Speed Control of a D.C. motor Motor Characterization Motor Speed Control Project 1. Generate PWM waveform 2. Amplify the waveform to drive the motor 3. Measure motor speed 4. Estimate motor parameters

More information

Fourier Signal Analysis

Fourier Signal Analysis Part 1B Experimental Engineering Integrated Coursework Location: Baker Building South Wing Mechanics Lab Experiment A4 Signal Processing Fourier Signal Analysis Please bring the lab sheet from 1A experiment

More information

ECE317 : Feedback and Control

ECE317 : Feedback and Control ECE317 : Feedback and Control Lecture : Frequency domain specifications Frequency response shaping (Loop shaping) Dr. Richard Tymerski Dept. of Electrical and Computer Engineering Portland State University

More information

Advanced Measurements

Advanced Measurements Albaha University Faculty of Engineering Mechanical Engineering Department Lecture 9: Wheatstone Bridge and Filters Ossama Abouelatta o_abouelatta@yahoo.com Mechanical Engineering Department Faculty of

More information

Laboratory PID Tuning Based On Frequency Response Analysis. 2. be able to evaluate system performance for empirical tuning method;

Laboratory PID Tuning Based On Frequency Response Analysis. 2. be able to evaluate system performance for empirical tuning method; Laboratory PID Tuning Based On Frequency Response Analysis Objectives: At the end, student should 1. appreciate a systematic way of tuning PID loop by the use of process frequency response analysis; 2.

More information

Department of Electrical & Computer Engineering Technology. EET 3086C Circuit Analysis Laboratory Experiments. Masood Ejaz

Department of Electrical & Computer Engineering Technology. EET 3086C Circuit Analysis Laboratory Experiments. Masood Ejaz Department of Electrical & Computer Engineering Technology EET 3086C Circuit Analysis Laboratory Experiments Masood Ejaz Experiment # 1 DC Measurements of a Resistive Circuit and Proof of Thevenin Theorem

More information

E40M Sound and Music. M. Horowitz, J. Plummer, R. Howe 1

E40M Sound and Music. M. Horowitz, J. Plummer, R. Howe 1 E40M Sound and Music M. Horowitz, J. Plummer, R. Howe 1 LED Cube Project #3 In the next several lectures, we ll study Concepts Coding Light Sound Transforms/equalizers Devices LEDs Analog to digital converters

More information

2015 HBM ncode Products User Group Meeting

2015 HBM ncode Products User Group Meeting Looking at Measured Data in the Frequency Domain Kurt Munson HBM-nCode Do Engineers Need Tools? 3 What is Vibration? http://dictionary.reference.com/browse/vibration 4 Some Statistics Amplitude PDF y Measure

More information

Lecture 2 Analog circuits. Seeing the light..

Lecture 2 Analog circuits. Seeing the light.. Lecture 2 Analog circuits Seeing the light.. I t IR light V1 9V +V IR detection Noise sources: Electrical (60Hz, 120Hz, 180Hz.) Other electrical IR from lights IR from cameras (autofocus) Visible light

More information

Resonator Factoring. Julius Smith and Nelson Lee

Resonator Factoring. Julius Smith and Nelson Lee Resonator Factoring Julius Smith and Nelson Lee RealSimple Project Center for Computer Research in Music and Acoustics (CCRMA) Department of Music, Stanford University Stanford, California 9435 March 13,

More information

PROBLEM SET 6. Note: This version is preliminary in that it does not yet have instructions for uploading the MATLAB problems.

PROBLEM SET 6. Note: This version is preliminary in that it does not yet have instructions for uploading the MATLAB problems. PROBLEM SET 6 Issued: 2/32/19 Due: 3/1/19 Reading: During the past week we discussed change of discrete-time sampling rate, introducing the techniques of decimation and interpolation, which is covered

More information

EE 482 : CONTROL SYSTEMS Lab Manual

EE 482 : CONTROL SYSTEMS Lab Manual University of Bahrain College of Engineering Dept. of Electrical and Electronics Engineering EE 482 : CONTROL SYSTEMS Lab Manual Dr. Ebrahim Al-Gallaf Assistance Professor of Intelligent Control and Robotics

More information

PHYS225 Lecture 15. Electronic Circuits

PHYS225 Lecture 15. Electronic Circuits PHYS225 Lecture 15 Electronic Circuits Last lecture Difference amplifier Differential input; single output Good CMRR, accurate gain, moderate input impedance Instrumentation amplifier Differential input;

More information

University of Michigan EECS 311: Electronic Circuits Fall 2008 LAB 2 ACTIVE FILTERS

University of Michigan EECS 311: Electronic Circuits Fall 2008 LAB 2 ACTIVE FILTERS University of Michigan EECS 311: Electronic Circuits Fall 2008 LAB 2 ACTIVE FILTERS Issued 9/22/2008 Pre Lab Completed 9/29/2008 Lab Due in Lecture 10/6/2008 Introduction In this lab you will design a

More information

H represents the value of the transfer function (frequency response) at

H represents the value of the transfer function (frequency response) at Measurements in Electronics and Telecommunication - Laboratory 4 1 Laboratory 4 Measurements of frequency response Purpose: Measuring the cut-off frequency of a filter. The representation of frequency

More information

Dynamic Vibration Absorber

Dynamic Vibration Absorber Part 1B Experimental Engineering Integrated Coursework Location: DPO Experiment A1 (Short) Dynamic Vibration Absorber Please bring your mechanics data book and your results from first year experiment 7

More information

The Fundamentals of Mixed Signal Testing

The Fundamentals of Mixed Signal Testing The Fundamentals of Mixed Signal Testing Course Information The Fundamentals of Mixed Signal Testing course is designed to provide the foundation of knowledge that is required for testing modern mixed

More information

Välkomna till TSRT15 Reglerteknik Föreläsning 8

Välkomna till TSRT15 Reglerteknik Föreläsning 8 Välkomna till TSRT15 Reglerteknik Föreläsning 8 Summary of lecture 7 More Bode plot computations Lead-lag design Unstable zeros - frequency plane interpretation Summary of last lecture 2 W(s) H(s) R(s)

More information

Operational Amplifier Circuits

Operational Amplifier Circuits ECE VIII. Basic 5 Operational Amplifier Circuits Lab 8 In this lab we will verify the operation of inverting and noninverting amplifiers constructed using Operational Amplifiers. We will also observe the

More information

Transfer Function (TRF)

Transfer Function (TRF) (TRF) Module of the KLIPPEL R&D SYSTEM S7 FEATURES Combines linear and nonlinear measurements Provides impulse response and energy-time curve (ETC) Measures linear transfer function and harmonic distortions

More information

CDS 101/110a: Lecture 8-1 Frequency Domain Design. Frequency Domain Performance Specifications

CDS 101/110a: Lecture 8-1 Frequency Domain Design. Frequency Domain Performance Specifications CDS /a: Lecture 8- Frequency Domain Design Richard M. Murray 7 November 28 Goals:! Describe canonical control design problem and standard performance measures! Show how to use loop shaping to achieve a

More information

ACTIVE VIBRATION CONTROL OF HARD-DISK DRIVES USING PZT ACTUATED SUSPENSION SYSTEMS. Meng-Shiun Tsai, Wei-Hsiung Yuan and Jia-Ming Chang

ACTIVE VIBRATION CONTROL OF HARD-DISK DRIVES USING PZT ACTUATED SUSPENSION SYSTEMS. Meng-Shiun Tsai, Wei-Hsiung Yuan and Jia-Ming Chang ICSV14 Cairns Australia 9-12 July, 27 ACTIVE VIBRATION CONTROL OF HARD-DISK DRIVES USING PZT ACTUATED SUSPENSION SYSTEMS Abstract Meng-Shiun Tsai, Wei-Hsiung Yuan and Jia-Ming Chang Department of Mechanical

More information

Test No. 1. Introduction to Scope Measurements. Report History. University of Applied Sciences Hamburg. Last chance!! EEL2 No 1

Test No. 1. Introduction to Scope Measurements. Report History. University of Applied Sciences Hamburg. Last chance!! EEL2 No 1 University of Applied Sciences Hamburg Group No : DEPARTMENT OF INFORMATION ENGINEERING Laboratory for Instrumentation and Measurement L: in charge of the report Test No. Date: Assistant A2: Professor:

More information

Study of Inductive and Capacitive Reactance and RLC Resonance

Study of Inductive and Capacitive Reactance and RLC Resonance Objective Study of Inductive and Capacitive Reactance and RLC Resonance To understand how the reactance of inductors and capacitors change with frequency, and how the two can cancel each other to leave

More information

Part 2: Second order systems: cantilever response

Part 2: Second order systems: cantilever response - cantilever response slide 1 Part 2: Second order systems: cantilever response Goals: Understand the behavior and how to characterize second order measurement systems Learn how to operate: function generator,

More information

Homework Assignment 10

Homework Assignment 10 Homework Assignment 10 Question The amplifier below has infinite input resistance, zero output resistance and an openloop gain. If, find the value of the feedback factor as well as so that the closed-loop

More information

DESIGN AND ANALYSIS OF FEEDBACK CONTROLLERS FOR A DC BUCK-BOOST CONVERTER

DESIGN AND ANALYSIS OF FEEDBACK CONTROLLERS FOR A DC BUCK-BOOST CONVERTER DESIGN AND ANALYSIS OF FEEDBACK CONTROLLERS FOR A DC BUCK-BOOST CONVERTER Murdoch University: The Murdoch School of Engineering & Information Technology Author: Jason Chan Supervisors: Martina Calais &

More information

CDS 101/110: Lecture 8.2 PID Control

CDS 101/110: Lecture 8.2 PID Control CDS 11/11: Lecture 8.2 PID Control November 16, 216 Goals: Nyquist Example Introduce and review PID control. Show how to use loop shaping using PID to achieve a performance specification Discuss the use

More information

Lecture 48 Review of Feedback HW # 4 Erickson Problems Ch. 9 # s 7 &9 and questions in lectures I. Review of Negative Feedback

Lecture 48 Review of Feedback HW # 4 Erickson Problems Ch. 9 # s 7 &9 and questions in lectures I. Review of Negative Feedback Lecture 48 Review of Feedback HW # 4 Erickson Problems Ch. 9 # s 7 &9 and questions in lectures I. Review of Negative Feedback A. General. Overview 2. Summary of Advantages 3. Disadvantages B. Buck Converter

More information

Servo Loop Bandwidth, Motor Sizing and Power Dissipation. Mark Holcomb Senior Engineer, Motion Control Specialist Celera Motion

Servo Loop Bandwidth, Motor Sizing and Power Dissipation. Mark Holcomb Senior Engineer, Motion Control Specialist Celera Motion Servo Loop Bandwidth, Motor Sizing and Power Dissipation Mark Holcomb Senior Engineer, Motion Control Specialist Celera Motion Professional Background University of Buffalo, 1994 MS ME Active Systems product

More information