SITRANS F flowmeters SITRANS F US. SITRANS FUS880 (retrofit kit) 4/218 Siemens FI

Transcription

1 SITRNS F flowmeters Siemens G 2007 Overview pplication Irrigation systems Irrigation distribution systems Pumping stations Canal laterals On-farm outlets Water well production rip and sprinkler irrigation Center pivot systems Potable water The SITRNS FUS880 is a battery-powered irrigation flowmeter, designed for pipes measuring from N 200 up to N 1200 (8" up to 8") in diameter. The SITRNS FUS880 gives you the ability to install the flowmeter underground retrofitting onto existing pipelines. This ultrasonic transient time irrigation flowmeter is used for full pipe flow measurements. may be PVC or concrete and pipe construction may be single wall or double wall, smooth or corrugated. The flowmeter produces a signal proportional to the velocity of the flow (flow rate) as the liquid flows past the ultrasonic sensors. SITRNS FUS880 has transducers in the flow (in-line) which assures superior aides in accuracy and superior performance when compared to doppler or many other types of flow measurement systems. Benefits Cost-effective solution - contains all the necessary components for retrofitting onto existing pipe Battery operated - Maintenance free up to 6 years SITRNS FUS880 is easy to install in pipeline sizes from N 200 up to N 1200 (8" up to 8") in diameter The transmitter display shows both accumulated volume and instantaneous flow rate The flowmeter provides a digital signal that can be sent directly to a PLC/RTU/CS Solid construction with no moving parts for a 100% maintenance and obstruction free flowmeter The SITRNS FUS880 transmitter comes within an IP67 enclosure Sensor can easily be buried and withstand constant flooding utomatic calculation of the calibration factor when pipe geometry data are entered in the signal transmitter may be polyvinylchloride (PVC) or concrete Pipe construction may be single wall or double wall, smooth or corrugated esign The SITRNS FUS880 set contains all necessary parts to build up an ultrasonic flowmeter on existing pipes depending on choices at ordering: s to wrap around pipes for alignment of sensors Transducer threading tool Thread adapters Transducer alignment tools Mounting plugs or saddles as well as FUS880 transmitter dependant upon the specifics at time of ordering and required mounting hardware Cables Technical specifications SITRNS FUS880 ccuracy Typical ± 2.0%, dependant upon the accuracy of measurements of tube diameter and during installation Note: Flow system measurement performance depends on the accuracy of the measurements taken at time of installation. This means that inaccurate measurements of angles, distance between transducers, wall thickness and pipe diameter have a direct effect on the accuracy as these values measured are entered into the memory of the FUS880 transmitter and used in part of the calculation of flow rate. Requirements for pipes Size N N 1200 (8"... 8" ) Transmitter Enclosure Rating IP67 rated enclosure Material Fiberglass reinforced polyamide Terminal box P 6.6, 100 C (212 F) Transducer element ISI 316 Stainless Steel 200 C (392 F) 2000 Corrugated PVC Transducer holder: Polyvinyl chloride Pressure rating per spec. STM -178 (5.5 bar (80 psi)) Liquid temperature max. Temperature rating per spec. STM -178 (60 C (10 F)) Pro21 Corrugated PVC Transducer holder: Polyvinyl chloride Pressure rating per spec. STM -178 (5.5 bar (80 psi)) Liquid temperature max. Temperature rating per spec. STM -178 (60 C (10 F)) /218 Siemens FI

2 Siemens G 2007 SITRNS F flowmeters PVC Solid PIP 80 Transducer holder: Polyvinyl chloride Pressure rating per spec. STM -178 (5.5 bar (80 psi)) Liquid temperature max. Temperature rating per spec. STM -178 (60 C (10 F)) Concrete Transducer holder: Polyvinyl chloride Pressure rating per spec. STM -178 (5.5 bar (80 psi)) Liquid temperature max. Temperature rating per spec. STM -178 (60 C (10 F)) Structural Epoxy joint meets spec. STM 1002 (118 bar or 1710 psi) Pipe wall thickness 2000 Corrugated PVC mm (1"... 2") Pro21 Corrugated PVC mm (1"... 2") PVC Solid PIP 80 Less than 25 mm (1") Concrete mm ( ) mm ( ) mm ( ) mm ( ) mm ( ) mm ( ) mm ( ) More information Installation requirement The space requirements around the pipe for retrofitting an ultrasonic flowmeter type SITRNS FUS880 are given below: It is important to prepare excavation site for a safe and efficient installation. n underground pipe needs to be exposed so that there is a minimum of 1.52 m (5 ft) or more of working space on either side of the pipe. The length of the trench should exceed the template length by 1.83 m (6 ft) or more. Pipe support: Ensure that an unearthed pipe has sufficient support beneath it to prevent deformation or breakage. Cave-in: lways brace trench walls. Follow all applicable (e.g. municipal, company, customer, site, union) construction guidelines. Epoxy: Follow all safety recommendations listed by the epoxy manufacturer. Use proper protection equipment, such as gloves, safety glasses, clothing, etc. Read the labels on the epoxy cans before mixing. Note all safety related statements and temperature recommendations in particular. For additional information, see the epoxy manufacturer's internet site. Pipe template: s are printed on a durable material, such as Mylar, and are resistant to normal contaminants. o not expose the template to excessive moisture or excessive periods of sunlight, heat and cold temperatures. lways roll and store the template in its' shipping tube. o not stretch or fold as this could permanently damage the template. Installation overview: Installation steps Installation of the SITRNS FUS880 is accomplished with the following steps. 1. Expose and clean the pipe. 2. Mark a centerline on the pipe. 3. Place the template on the pipe and tape it securely to the pipe.. Mark the locations of the sensor mounting holes on the pipe. 5. rill the sensor mounting holes in the pipe. 6. Clean and de-burr the sensor mounting area. 7. Measure up the pipe circumference C, the wall thickness WT and calculate O and I. 8. Epoxy and screw the saddle sensor holder to the pipe. 9. ssemble and install the sensors-holders. 10. Measure up the actual sensor-location to see if re-calibration is needed. 11. ssemble and install the sensors. 12. Install sensor wiring and conduit. 13. Install the transmitter and connect the sensor wiring. 1. Check the transmitter configuration. 15. Test the installation thoroughly and run a flow test. 16. Fill in the "Site cceptance Form". 17. Cover the pipe. For detailed instruction in installation please refer to User Manual Order no.: FK:521HP0553. Siemens FI /219

3 SITRNS F flowmeters Siemens G 2007 SONOFLO Ultrasonic flowmetersf) 7ME30- SITRNS FUS880 PVC (Solid) (PIP80) SONOKIT N 200 (8") 2 F N 250 (10") 2 K N 300 (12") 2 P N 380 (15") 2 V N 50 (18") 3 F N 530 (21") 3 M N 600 (2") 3 T N 680 (27") Less than 25 mm (1 ) B PVC (Solid) (PIP80) 1 2-track X-configuration 3 Transmitters SITRNS FUS080, IP67, 20 m (65.6 ft) with gland dd on units of measure Flow unit MG x 100 x 1000 Volume unit cf (cre Feet) Volume unit ci (cre Inch) L2 L L6 L9 L8 L3 SONOFLO Ultrasonic flowmetersf) 7ME30- SITRNS FUS Corrugated PVC SONOKIT 1-track N 380 (15") 2 V N 50 (18") 3 F N 530 (21") 3 M N 600 (2") 3 T N 750 (30") K N 900 (36") 5 B mm ( ) C PVC Corrugated Transmitter SITRNS FUS080, IP67, 20 m (65.6 ft) with gland dd on units of measure Flow unit MG x 100 x 1000 Volume unit cf (cre Feet) Volume unit ci (cre Inch) L2 L L6 L9 L8 L3 F) Subject to export regulations L: 9I999, ECCN: N. /220 Siemens FI

4 Siemens G 2007 SITRNS F flowmeters SONOFLO Ultrasonic flowmetersf) 7ME30- SITRNS FUS880 Pro21 Corrugated PVC SONOKIT 1-track N 750 (30") K N 80 (33") P N 900 (36") 5 B N 1050 (2") 5 M N 1200 (8") 5 T mm ( ) C PVC Pro21 Corrugated 2 Transmitter SITRNS FUS080, IP67, battery powered 20 m (65.6 ft) with gland dd on units of measure Flow unit MG x 100 x 1000 Volume unit cf (cre Feet) Volume unit ci (cre Inch) L2 L L6 L9 L8 L3 SONOFLO Ultrasonic flowmetersf) 7ME30- SITRNS FUS880 Concrete SONOKIT 1-track N 300 (12") 2 P N 380 (15") 2 V N 50 (18") 3 F N 530 (21") 3 M N 600 (2") 3 T N 680 (27") N 750 (30") K N 900 (36") 5 B N 1050 (2") 5 M mm ( ) mm ( ) E mm ( ) F mm ( ) G mm ( ) H mm ( ) J mm ( ) K Concrete Transmitter SITRNS FUS080, IP67, battery powered 20 m (65.6 ft) with gland dd on units of measure Flow unit MG x 100 x 1000 Volume unit cf (cre Feet) Volume unit ci (cre Inch) L2 L L6 L9 L8 L3 F) Subject to export regulations L: 9I999, ECCN: N. Siemens FI /221

5 SITRNS F flowmeters Siemens G 2007 F) ccessories and Spare parts SONOFLO Ultrasonic flowmeters FUS880 transmitter includes 2 transducers and 20 m (65.6 ft) of cable FUS880 Installation pipe template, PCV. PIP 80 N 250 (10 ) N 300 (12 ) N 380 (15 ) N 50 (18 ) N 530 (21 ) N 600 (2 ) N 680 (27 ), Concrete N 300 (12 ) N 380 (15 ) N 00 (16 ) N 50 (18 ) N 530 (21 ) N 600 (2 ) N 680 (27 ) N 750 (30 ) N 900 (36 ) N 1050 (2 ), pipe N 900 (36 ) PVC, 2000 corrugated, pipe N 1050 (2 ) Pro21 corrugated 7ME TGX: TGX: TGX: TGX: TGX: TGX: TGX: TGX: TGX: TGX: TGX: TGX: TGX: TGX: TGX: TGX: TGX: TGX: TGX: FUS880 Installation spare kit Concrete kit, Sensor mounting mm ( ) TGX: K mm ( ) TGX: K mm ( ) TGX: K mm ( ) TGX: K mm ( ) TGX: K mm ( ) TGX: K mm ( ) TGX: K PVC kit, Sensor Mounting N 300 (12 ) TGX: K N 380 (15 ) TGX: K N 50 (18 ) TGX: K N 530 (21 ) TGX: K N 600 (2 ) TGX: K N 680 (27 ) TGX: K Corrugated PVC kit, N 900 (36 ) 2000 TGX: K Corrugated PVC kit, N 1050 (2 ) Pro21 TGX: K FUS880 spares Holder - Saddle N 250 (10 ) PIP 80 PVC Saddle TGX: N 300 (12 ) PIP 80 PVC Saddle TGX: N 380 (15 ) PIP 80 PVC Saddle TGX: N 50 (18 ) PIP 80 PVC Saddle TGX: N 530 (21 ) PIP 80 PVC Saddle TGX: N 600 (2 ) PIP 80 PVC Saddle TGX: N 680 (27 ) PIP 80 PVC Saddle TGX: F) Holder - Plug mm ( ) Cement sensor TGX: mm ( ) Cement sensor TGX: mm ( ) Cement sensor TGX: mm ( ) Cement sensor TGX: mm ( ) Cement sensor TGX: ("....25") Cement sensor TGX: mm ( ) Cement TGX: sensor N 900 (36 ) I TGX: PRO-21 - N 1050 (2 ) I TGX: Straps -Kits Strap kit for -13 & -135 plugs TGX: Strap kit for -120, -121, -122, -123 plugs TGX: Strap kit for -12 & -125 plugs TGX: Strap kit for -127 plug TGX: dhesive 1 lb epoxy 6X dapter Conduit adapter 6X Tools Sensor Wrench TGX: lignment Tool TGX: ocumentation Manual FK:521HP0553 Converter FUS880 converter kit for 2 track SYS 7ME Note: Installation spares kit include: Concrete kit: 2 transducer mounting plugs, 2 straps, mounting hardware, epoxy, conduit adapter, installation guide PVC kit: 2 transducer mounting saddles, mounting hardware, epoxy, conduit adapter, installation guide F) ll products on this page subject to export regulations L: 9I999, ECCN: N. /222 Siemens FI

6 ELLSONICS 北京迪妙声科技有限公司 BEJING ELLSONICS SCIENCE & TECHNOLOGY LT. 公司简介 北京迪妙声科技有限公司 ( 原名北京妙声力科技有限公司 ), 位于北京市海淀区中关村南大街, 是与西门子公司德国总部正式签约的西门子过程仪表及分析仪器核心合作伙伴, 也是西门子北方区域规模最大 实力最强的优秀代理商 公司主营 : 一 西门子 - 妙声力 (Milltronics) 系列物位产品 : 超声波物位计 超声波液位差计 超声波泥水界面计 超声波明渠流量计 雷达物位计 射频导纳物位计 射频导纳油水界面计 ; 射频导纳物位开关 音叉式物位开关 阻旋式物位开关 ; 皮带称 固体质量流量计 冲板流量计等 二 西门子过程仪表产品 : 电磁流量计 质量流量计 超声波流量计 温度变送器 压力变送器 阀门定位器 气体分析仪等 三 德国 UWT 公司的阻旋式料位开关 音叉式料位开关 重锤式料位计等产品 四 自行研发生产超声波液位计 温度变送器 压力变送器 数显表及油田专用仪器等产品 成立于 195 年的西门子 - 妙声力公司 (Milltronics) 是世界公认的超声波物位测量领域的领导者, 全球最大的超声波物位仪表生产厂家, 在超声波 雷达 电容技术领域拥有超过 60 项专利, 超声波产品的综合性能指标经美国 控制 杂志评比, 其综合性能名列全球第一! 作为西门子公司长期稳定的代理商, 我公司有着 10 余年产品的销售和服务经验, 无论从专业技术水平 现货及备件库存量 售后服务质量 仪表维护以及故障产品国内维修能力等方面, 都具备显著的优势 尤其是我公司一流的技术支持和高效率高品质的服务体系, 在业界具有很高的知名度 如果您需要相关的产品, 需要咨询技术问题, 需要值得信赖的合作伙伴, 敬请来电垂询! 商务部总机电话 : /31/32/33, , , ( 小灵通 ) 传真 : 总机转 50 谢谢您的合作与支持! 地址 : 北京海淀区魏公村街 1 号韦伯豪家园 (100081) 电话 : /31/32/33, , 传真 : 总机转 50 sales@dellsonics.com