S5X Mobile Microcomputer. Technical Information 223,5 82,25 77,75 8,5 8,5 164,5 10,3. AMP Stecker AMP Connector 52,5 POWER SYSTEM MODE STATUS

Transcription

1 S5X Mobile Microcomputer Technical Information ,5 POWER SYSTEM 82,25 77,75 MODE STATUS 9 164,5,3 AMP Stecker AMP Connector ,5

2 Overview DESCRIPTION The Sauer-Danfoss S5X Mobile Microcomputer is a digital electronic, designed for open loop as well as closed loop mobile off-road system applications. Specific for hydraulic driven forestry systems and road building systems. State of art controls in mobile applications driving rotary and linear actuators (hydrostatic transmissions, hydraulic cylinders etc.) are to be more flexible and intelligent. The robust design of the S5X digital electronic series provides best for this. The design provides the required performance for a mobile environment and high performance, 16 bit mirocontroller provides the capability for future expansion. It is possible to load several software programs via RS232 interface for various series without any hardware change. This feature makes it possible for an unexperienced operator to use standard hardware for different applications while the appropriate software is selected. The S5X software and hardware is designed for easy communication between the controller. Especially developed tools can be used to optimize the performance during production. This facility simplifies start-up, field service and stock. FEATURES Environmentally proofed for mobile applications. Supply voltage 12 V DC or 24 V DC. Software changes without hardware operations. Individual setup per software possible. Visual error output (Blink code for red Error LED). Diagnostic functions and emergency routines. Communication between S5X and Laptop via RS232. Update software download. TECHNICAL DATA Supply voltage: 12 V DC or 24 V DC Sensor voltage: 5 V DC up to 200 ma LED outputs: 2 (under software control). 2 (for internal voltages). All visible from outside the enclosure. Communication: RS232 full buffered. CAN Interface: Standard Specification V2.0 Part B (active). Physical layer: Standard ISO (High-Speed) Electrical connections: 42pin board-mounted AMP I/O connector. 16pin board-mounted AMP I/O connector for communication. Operation temperature: -40 C to +70 C Moisture: Protected against 95 % relative humidity and high pressure washdowns. Vibration: 5 to 2000 Hz with resonance dwell for 1 million cycles for each resonant point run from 1 to gs. Shock: 50 gs for 11 ms in all 3 axes for a total of 18 shocks. Electrical: The S5X is protected for short circuits to ground. The supply voltage must only be connected to the pins defined in a system connection diagram. Otherwise damage to the controller is possible. Withstands reverse polarity, over voltage, voltage transients, static discharge, EMI/RFI and load dump. 2001, Sauer-Danfoss Sauer-Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Sauer -Danfoss reserves the right to alter its products without prior notice. This also applies to products already ordered provided that such alterations can be made without subsequent changes being necessary in specifications already agreed. All trademarks in this material are properties of the respective companies. Sauer-Danfoss and the Sauer-Danfoss logotype are trademarks of the Sauer-Danfoss Group. All rights reserved. 2 BLN E Rev. E 12/2001

3 Technical Data S5X-11 G2 AMP K167C I/O Functions Description Battery input current max. 6 A Digital inputs high side switching. 5 Analog inputs 0 V DC to 5 V DC 3 Frequency inputs 1x 2-wire PPU and 2x 3-wire PPUs configured. 0 to khz. 2 Current feedback inputs high current measuring up to 2 A. 3 Proportional outputs unidirectional PWM outputs. 2 A high side switching. Can be used as digital outputs. 2 Actuator outputs bidirectional PWM outputs with internal current feedback. 4 Digital outputs 2 A high side switching. Controller Siemens SAF C167 CR-LM Memory Flash Memory: 1MByte RAM: 256kByte I 2 C EEPROM: 2kByte CAN Interface as described above. S5X-12 G2 AMP K196 I/O Functions Description Battery input current max. 6 A 6 Digital inputs high side switching. 4 Analog inputs 0 V DC to 5 V DC 3 Frequency inputs 1x 2-wire PPU and 2x 3-wire PPUs configured. 0 to khz. 3 Proportional outputs unidirectional PWM outputs. 2 A high side switching. 3 Gear switch outputs 4 A low side switching. 4 Digital outputs 2 A high side switching. Controller Intel 80C196 KC Memory Flash Memory: 128kByte RAM: 8kByte I 2 C EEPROM: 2kByte S5X-15 G2 AMP K167C I/O Functions Description Battery input current max. 12 A Digital inputs high side or low side switching. Selectable via software. Analog inputs 0 V DC to 5 V DC 6 Frequency inputs 2- or 3-wire PPU. Selectable via software. 0 to khz. Proportional outputs unidirectional PWM outputs. or EDC outputs 2 A high side switching. max. 8 prop. outputs or max. 6 EDC outputs or mixed. 2 Actuator outputs can be used as digital outputs. 4 Digital outputs 2 A high side switching. Controller Siemens SAF C167 CR-LM Memory Flash Memory: 1MByte RAM: 256kByte I 2 C EEPROM: 2kByte CAN Interface as described above. BLN E Rev. E 12/2001 3

4 Dimensions LED OVERVIEW ,5 7 6 POWER SYSTEM ,25 77,75 MODE STATUS 9 164,5, ,5 1 S5X 2 Mounting slots 3 AMP connectors 4 Diagnostic LED red Error check (STATUS) Lights up if an error is detected. 5 Diagnostic LED yellow Software check (MODE) Flashes with approx. 0.5Hz (slow), if the program is running fine. Flashes with approx. 5Hz (fast), if no program is loaded. Shining if in setup mode. 6 Diagnostic LED green 5V DC internal (SYSTEM) Lights up if 5V DC internal is O.K. 7 Diagnostic LED green Battery after ignition switch (POWER) Lights up if the battery voltage is connected after ignition. S01752a 4 BLN E Rev. E 12/2001

5 Environmental Tests ENVIRONMENTAL TESTS EMC-Standards, MCES015 Immunity Test principle Severity level Radiation (stripline) ISO : V/m (1 MHz MHz) Radiation (antenna) ISO : V/m (200 MHz - 00 MHz) ESD ISO TR 605: kv / 8 kv Impulsive disturbances DIN part 1:.1992 pulse 1: -200 V applied to supply leads pulse 2: +0 V pulse 3a: -200 V pulse 3b: +200 V pulse 4: Us -16 / -7 V pulse 5: +200 V Impulsive disturbances DIN part 3: pulse 1: -60 V applied to transmitter pulse 2: +30 V and signal leads pulse 3a: -80 V pulse 3b: +80 V Emission Test principle Limit value met (Radio interference) Electrical disturbance Directive 95/54/EEC EUB/narrowband field strength EUB/broadband Disturbance voltage DIN part 3: Degree of suppression 5 (0,15 MHz - 30 MHz) Degree of suppression 4 (87,5 MHz - 8 MHz) Mechanical Standards, MCES015 Mechanical vibration Test principle Severity level Random DIN IEC h in each of 3 orthogonal axes at 5.58 g 50 Hz Hz Resonance Search DIN IEC Hz Hz at the rate of 1 octave per minute 4 g throughout sweep Resonance Dwell time DIN IEC g throughout sweep 5 minutes dwell time Mechanical Shock DIN IEC shocks in each direction of the three major orthogonal axes 50 g throughout sweep with 11 ms Temperature test Test principle Severity level Temperature shock DIN IEC C max. temperature -40 C min. temperature 1 h dwell time 24 h test cycle time Salt test Test principle Severity level Salt spray DIN IEC % NaCl at 35 C / 72 h BLN E Rev. E 12/2001 5

6 OUR PRODUCTS Hydrostatic transmissions Hydraulic power steering Electric power steering Closed and open circuit axial piston pumps and motors Gear pumps and motors Bent axis motors Radial piston motors Orbital motors Transit mixer drives Planetary compact gears Proportional valves Sauer-Danfoss Hydraulic Power Systems Market Leaders Worldwide Sauer-Danfoss is a comprehensive supplier providing complete systems to the global mobile market. Sauer-Danfoss serves markets such as agriculture, construction, road building, material handling, municipal, forestry, turf care, and many others. We offer our customers optimum solutions for their needs and develop new products and systems in close cooperation and partner ship with them. Sauer-Danfoss specializes in integrating a full range of system components to provide vehicle designers with the most advanced total system design. Sauer-Danfoss provides comprehensive worldwide service for its products through an extensive network of Authorized Service Centers strategically located in all parts of the world. Directional spool valves Cartridge valves Hydraulic integrated circuits Hydrostatic transaxles Integrated systems Fan drive systems Electrohydraulic controls Digital electronics and software Battery powered inverter Sensors Sauer-Danfoss (US) Company 2800 East 13th Street Ames, IA 500, USA Phone: , Fax: Sauer-Danfoss (Neumünster) GmbH & Co. OHG Postfach 2460, D Neumünster Krokamp 35, D Neumünster, Germany Phone: , Fax: Sauer-Danfoss (Nordborg) A/S DK-6430 Nordborg, Denmark Phone: , Fax: Sauer-Danfoss (US) Company 3500 Annapolis Lane North Minneapolis, MN 55447, USA Phone: , Fax: BLN E Rev. E 12/2001