CONTINUOUS COUNTERPOISE ON POLES
|
|
- Dominick Butler
- 5 years ago
- Views:
Transcription
1 Project Procedure CONTINUOUS COUNTERPOISE ON POLES 07/25/2011 PAGE 1 OF PURPOSE The purpose of this procedure is to provide guidance and direction for the installation of continuous counterpoise on poles to improve structure footing resistance. Pole footing resistance measurements shall be taken on each pole prior to making counterpoise connections. 2.0 SCOPE The scope of this procedure applies to Pike construction activities. This procedure may also be applied to Contractors when invoked by Contract documents. 3.0 REFERENCES 3.1 Project Procedure P-1-4, Quality Control Functions and Responsibilities (Construction Site) 3.2 Project Procedure P-1-5, Quality Control Personnel Assignments (Construction Site) 4.0 DEFINITIONS None 5.0 RESPONSIBILITIES Personnel responsibilities are as defined in the procedures P-1-4, Quality Control Functions and Responsibilities (Reference 3.1), and P-1-5, Quality Control Personnel Assignments (Reference 3.2). 6.0 PROCEDURE FOR INSTALLING CONTINUOUS COUNTERPOISE ON POLES 6.1 Notify the underground locating service if underground facilities cannot be located. 6.2 Load reel of wire into the wire cart using the sideloader The sideloader transports wire to the job site. 6.3 Transport the wire and cart to the counterpoise site using a bulldozer.
2 PAGE 2 OF Set up the wire cart facing the desired direction of pull and 6 to 8 from the centerline of the pole using a bulldozer. See Attachment 8.1, Excavation and Connection Processes, for details. 6.5 If counterpoise will be plowed in two directions, excavate a 4 deep hole for splicing using a backhoe. Note: Depending on terrain it may be necessary to set up reel so wire can be pulled in both directions, e.g., pull from the top of the hill to valleys in both direction. See Attachment 8.3, Counterpoise Installation in Two Directions, for an example. Set wire cart up close enough to pole so wire cart ground lead can be connected to down pole ground. 6.6 Place the rubber mat on the ground under the wire cart brake Place a rubber blanket on the rubber mat for the technician to stand on. 6.7 Loosen the wire cart brake. 6.8 Attach the ground lead from the wire cart to the closest pole ground and tighten the ground clamp. 6.9 Feed the wire off the wire cart through the wire guide Feed enough wire off the wire cart to reach and attach to the plow foot Cut pasture fences if necessary, but repair the before leaving. See Paragraph If the distance is impeded by an obstruction, do not plow in less than 75 of counterpoise Attach rolling ground to the counterpoise wire Connect rolling ground to the wire cart with a rope Make a dry run (a plowing trench without wire), using a bulldozer if necessary, parallel to overhead conductor and as close to the poles as possible for the entire length of the pull A dry run may be necessary due to power of equipment or terrain Return to the wire cart with the bulldozer after completing a dry run Feed wire up through bottom and second eye of plow foot and then into come-along Wire Cart Attendant shall wear rubber gloves and stand on rubber blanket when tending wire cart.
3 PAGE 3 OF Start to plow in counterpoise wire Lower plow foot to the desired depth (30 for uncultivated land and 36 for cultivate land) Adjust brake on the wire cart until the wire pays out without backlash. Note: Bulldozer Operator must have a radio with a headset and be prepared to stop if a joint in the wire hangs on the reel, if rolling ground occurs, or if wire must be spliced Plow the counterpoise wire into the trench as far as terrain, obstruction, or wire length will allow. See Attachment 8.3, Counterpoise Installation in Two Directions, for details. Note: If the distance of the pull is impeded by an obstruction, do not plow in less than 75 of counterpoise Bulldozer Operator stops at the end of the pull and backs up enough to remove tension from the wire Bulldozer Operator releases the come-along Bulldozer Operator notifies the Wire Cart Attendant to lock the reel brake Wire Cart Attendant locks the reel brake and notifies Bulldozer Operator Bulldozer Operator moves the bulldozer forward until the wire is free from the plow foot Bulldozer Operator notifies Wire Cart Attendant when the wire clears the plow Wearing rubber gloves, Wire Cart Attendant cuts the wire with ratchet bolt cutters. Note: If plowing counterpoise wire in two directions, cut the wire long enough to connect both leads together. See Attachment 8.1, Excavation and Connection Processes, for details Bulldozer Operator returns to the wire cart, using the weight of the bulldozer to compact earth disturbed by the plow Roll up running ground lead on the wire cart Remove the wire cart ground from the pole ground and roll up on the wire cart Bulldozer operator relocates wire cart to next counterpoise installation If wire must be plowed in opposite direction, use bulldozer to turn wire cart around and repeat Paragraphs 6.8 through Set up the backhoe over the top of the buried counterpoise adjacent to the pole. See Attachment 8.1, Excavation and Connection Processes, for details.
4 PAGE 4 OF Excavate a 3 to 4 deep hole using backhoe to expose the counterpoise wire Extend a trench over to the down pole ground wire on the pole Do not damage the pole during excavation. Trench should be a minimum of 12 deep at the pole and slope away from the pole to reduce moisture Excavations deeper than 5 must have shoring installed Remove soil from around the down pole ground to a depth of 12 using a shovel. See Attachments 8.1, Excavation and Connection Processes, and 8.2, Counterpoise Connection to Steel Pole, for details Clean the down pole ground (wooden or concrete poles only) and counterpoise using a steel brush Install personal protective grounds Connect two counterpoise wires together in excavation using a galvanized three boltparallel groove clamp Cut a piece of 5/16 copperweld wire to extend from the down pole ground or the ground flange to the counterpoise conductor Install a terminal lug connector on the light duty steel pole, and insert 5/16 copperweld wire into the connector and tighten. See Attachment 8.2, Counterpoise Connection to Steel Pole, for more details Install a wire-to-wire grounding clamp onto counterpoise, and insert 5/16 copperweld wire from the pole and tighten Wearing rubber gloves, remove the ground(s) from the counterpoise and pole Backfill excavations with a backhoe or a bulldozer, and compact the soil by moving a backhoe back and forth across the backfill Repeat Paragraphs 6.33 through 6.44 for counterpoise connections in other excavations. See Attachment 8.1, Excavation and Connection Processes, for details. Note: A pole footing resistance measurement shall be taken on initial counterpoise connection only. No measurements are required on additional poles in pull Seed all areas disturbed by the excavations Use wildlife mix seed for general open right of way. Use Fescue seed for pasture and residential lands. Do not sow seed on cultivated lands Repair any fences.
5 PAGE 5 OF DATA COLLECTION 7.1 Data collection forms are always required with this procedure See QF A, Counterpoise Installation Record for Poles (see Form 9.1). 8.0 ATTACHMENTS 8.1 Excavation and Connection Processes 8.2 Counterpoise Connection to Steel Pole 8.3 Counterpoise Installation in Two Directions 9.0 FORMS 9.1 Quality Form QF A, Counterpoise Installation Record for Poles 10.0 REVISIONS AND APPROVALS Revision Level Revision Date Revision Description Department Head (Approver) 0 09/10/2010 Original Issue Audie Simmons 1 07/25/2011 Updated logo and company name N/A
6 ATTACHMENT 8.1 EXCAVATION AND CONNECTION PROCESSES PAGE 1 OF 1
7 ATTACHMENT 8.2 COUNTERPOISE CONNECTION TO STEEL POLE PAGE 1 OF 1 STEEL POLE Counterpoise Material Item Quantity Description 2 lbs. Wire, Copperweld, 5/16 1 Clamp, Grounding, Wire-to-Wire 1 Connector, Terminal Lug 1 Washer, Round 9/16 Hole
8 ATTACHMENT 8.3 COUNTERPOISE INSTALLATION IN TWO DIRECTIONS PAGE 1 OF 1
9 FORM 9.1 PAGE 1 OF 3 COUNTERPOISE INSTALLATION RECORD FOR POLES Project: Client: Data Sheet/Rev: Description: Meter Type Used (Check one) Note: To be completed for each structure Job Number: Location: Date: Recorded By: Contractor: Megger Structure Number: Clamp-on Smart Meter Structure Type: Notes: 1. If the initial ground reading is less than 15 ohms, no additional action is required. 2. If the initial ground resistance reading is greater than 15 ohms, install 200 ft. runs of counterpoise. 3. After installing a length of counterpoise, if the next ground resistance reading does not drop by 10 ohms or greater STOP. 4. If counterpoise is required, but it cannot be installed due to site conditions, skip to Step 10. List # Units Installed Step Description Record original ground reading made. Refer to the notes above. If additional counterpoise is required, go to Step 2. Install 5/16 copperweld counterpoise and connect to the structure. Make a new TG ground reading and record. If the difference between his reading and the last reading is less than 10 ohms STOP. If the new reading is less than 15 ohms STOP. If the new read is greater than 15 ohms, continue to Step 4. TG Reading CP Install 5/16 copperweld counterpoise and connect to the structure. Quality Form QF A, Rev. 1 Last Revised: 07/25/2011 Project Procedure P Page 1 of 3
10 FORM 9.1 PAGE 2 OF 3 COUNTERPOISE INSTALLATION RECORD FOR POLES Project: Client: Data Sheet/Rev: Description: Step 5 Description Job Number: Location: Date: Make a new TG ground reading and record. If the difference between this reading and the last reading is less than 10 ohms STOP. If the new reading is less than 15 ohms STOP. If new reading is greater than 15 ohms, continue to Step 6. List TG Reading # Units Installed CP Install 5/16 copperweld counterpoise and connect to the structure. Make a new TG ground reading and record. If the difference between this reading and the last reading is less than 10 ohms STOP. If the new reading is less than 15 ohms STOP. If the new reading is greater than 15 ohms, continue to Step 8. Install 5/16 copperweld counterpoise and connect to the 8 structure. 9 Make new TG ground reading and record. If counterpoise cannot be installed, install 4 double ground rods 10 and tie together with counterpoise. Repeat Step 9. Quality Form QF A, Rev. 1 Last Revised: 07/25/2011 Project Procedure P Page 2 of 3
11 FORM 9.1 PAGE 3 OF 3 COUNTERPOISE INSTALLATION RECORD FOR POLES Project: Client: Data Sheet/Rev: Description: Job Number: Location: Date: Draw as-built below showing counterpoise installed and step number. R/W Edge Higher Number Structure Lower Number Remarks: R/W Edge Signature Print Name Date Performed By: Approved By: Accepted By: Quality Form QF A, Rev. 1 Last Revised: 07/25/2011 Project Procedure P Page 3 of 3
SECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP
1 1 1 0 1 0 1 0 1 SECTION 1 1 CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP BASED ON DFD MASTER SPECIFICATION DATED /01/ P A R T 1 - G E N E R A L SCOPE The work under this section shall consist of
More informationSECTION 5 TRANSFORMERS
SECTION 5 TRANSFORMERS Necessary transformers will be installed and maintained by The City of Aspen. The City of Aspen will not furnish transformers unless they are of standard size and voltage as established
More informationCITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST
CITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO. 2012-16A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST 2014 CHAIN LINK FENCE SPECIFICATIONS Chain link fence,
More informationSDCS-03 DISTRIBUTION NETWORK GROUNDING CONSTRUCTION STANDARD (PART-I) UNDERGROUND NETWORK GROUNDING. Rev. 01
SDCS-03 DISTRIBUTION NETWORK GROUNDING CONSTRUCTION STANDARD (PART-I) UNDERGROUND NETWORK GROUNDING Rev. 01 This specification is property of SEC and subject to change or modification without any notice
More informationMounting Instructions for Cisco Aironet 1550 Series Outdoor Access Point Pole-Mount Kits
Mounting Instructions for Cisco Aironet 1550 Series Outdoor Access Point Pole-Mount Kits Date: April 2011 Part number: This document describes how to use the Cisco Aironet 1550 Series Outdoor Access Point
More informationPAC-12 Kit Contents. Tools Needed Soldering iron Phillips screwdriver Wire stripper Wrenches, 7/16 and 1/2 Terminal crimp tool Pliers Solder
PAC-2 Kit Contents Part Quantity Screws: 8/32 x 3/8 Screws: 8-32 x 5/6 Screw: 8-32 x /4 #8 internal tooth washers #8 solder lug ring terminals Bolt: Aluminum, /4-20 x.5 /4 internal tooth washer Nut: Aluminum
More informationEXCAVATION AND BACKFILL
Standard Specification 2565.3, 2451, and 1805 A basic understanding of specifications is needed to properly replace the disturbed soil and restore the condition of the excavated area. The size of the disturbed
More informationSUBSTATION SECURITY WALL INSTALLATION MANUAL
SUBSTATION SECURITY WALL INSTALLATION MANUAL JULY 26, 2016 OLDCASTLE PRECAST, INC. 3000 New McEver Rd, Acworth, Ga 30101 Substation Security Wall Installation Manual This Installation Manual is intended
More informationClampStar Safe-T-Link Tether Installation Instructions for Deadends
Tel.800-269-1462 Fax.800-311-9857 P.O. Box 100279, Birmingham, AL 35210 www.classicconnectors.com Classic Connectors, Inc. ClampStar Safe-T-Link Tether Installation Instructions for Deadends General Safety
More informationNEW OR UPGRADED ELECTRICAL SERVICE
NEW OR UPGRADED ELECTRICAL SERVICE The following steps summarize the general process and procedures necessary for CVEA to complete construction of a new or upgraded service. Variances may be necessary
More informationRayport G Eco Dealer Kit
Rayport G Eco Dealer Kit Installation Guide www.aetenergy.com Supporting a Cleaner, Greener Tomorrow 1. Table of Contents 1. Table of Contents P2 2. Installer Notes P3 3. Parts List P4-7 4. Tool List P8
More informationConstructing Wire Fences
1 of 6 12/3/2010 9:48 AM University of Missouri Extension G1192, Reviewed October 1993 Constructing Wire Fences Richard E. Phillips Department of Agricultural Engineering This guide will provide some basic
More informationINSTALLATION & TESTING OF UNDERGROUND PRIMARY AND SECONDARY POWER CABLES PRIOR TO ENERGIZATION
TITLE: RECOMMENDED: P. Lemay NO: APPROVED: C. Malone, P.Eng. REV. DATE: 2015-11-02 Working Procedure GCG0001 REV: 3 INSTALLATION & TESTING OF UNDERGROUND PRIMARY AND SECONDARY POWER CABLES PRIOR TO ENERGIZATION
More informationClearSpan PolyMax Windbreak Wall
ClearSpan PolyMax Windbreak Wall Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: April 2007ldg STK# DIMENSIONS
More informationA. Deviation from this standard must be approved by the Project Architect.
September 2012, rev. 00 26 5600 Exterior Lighting PART 1. GENERAL 1.01 Related Documents A. Deviation from this standard must be approved by the Project Architect. B. Drawings and general provisions of
More informationAPPENDIX FENCE GENERAL NOTES
APPENDIX FENCE GENERAL NOTES 1. Fabric: 9 gage, 2" mesh, knuckle top and bottom, placed on the outside of posts, single fabric width for the entire height. 2. All fencing to be standard galvanized finish.
More informationINSTALLATION INSTRUCTIONS
STRIP DOORS AIR DOORS INSTALLATION INSTRUCTIONS BULK PVC FILM STRIP SHEET PANEL SCREENS, CURTAINS and ENCLOSURES MEGA-PRO SWINGING DOORS DOCK ACCESSORIES IMPORTANT Carefully examine the carton(s) for damage.
More informationRIDGE MAST MOUNT (RMM)
May 5, 009 Revision E ASSEMBLY MANUAL (RMM) General Dynamics Satcom Technologies 1500 PRODELIN DRIVE NEWTON NC 8658 88-464-4141 www.gdsatcom.com 1.0 INTRODUCTION: 1.1 Features: The Ridge Mast Mount (RMM)
More informationType 100 and Type 120 SMC Antenna System 1.0 Meter and 1.2 Meter Reflector with Az/El Cap Mount
Assembly Instructions Type 100 and Type 120 SMC Antenna System 1.0 Meter and 1.2 Meter Reflector with Az/El Cap Mount 8000284-01 Skyware Global 1315 Industrial Park Drive Smithfield, NC 27577 USA Telephone:
More informationModular XP Ramp Assembly Manual
Modular XP Manual 1 Contents Overview... 2-5 1.1 Tools required...6 1.2 Hardware list...6 Ramp & Platform Standard Parts 2.1 Ramp Parts...7 2.2 Platform Parts...8 2.3 Standard Platform Configurations...
More informationWhat you should have. 1. Telescopic Pole (1) 2. Arc tubing (4) for Lower Ring. 3. Numbered bars or spokes(8) 4. Center plate (1)
20 ft RGB Pole Tree What you should have 1. Telescopic Pole (1) 2. Arc tubing (4) for Lower Ring 3. Numbered bars or spokes(8) 4. Center plate (1) 5. Top Ring (1) 6. Hardware and wrenchs a. Hardware i.
More informationGrowSpan Round Cold Frames
GrowSpan Round Cold Frames Photo may show a different but similar model. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 103099 12' W x 8' H x 24'
More informationMONKEY BARS OVERHEAD RACK INSTALLATION
MONKEY BARS OVERHEAD RACK INSTALLATION Thank you for purchasing the New Monkey Bars Overhead storage rack. The most innovative overhead rack on the market WARNING THE PROPER INSTALLATION OF THIS STORAGE
More information6a. Eight Steps to Chain-Link Fence Installation
6a. Eight Steps to Chain-Link Fence Installation Before You Start You will need the following tools to install your chain-link fence: Post hole digger Wheelbarrow, shovel and hoe for mixing concrete Tape
More informationHigh Wheel Cultivator Model HWC-243A
High Wheel Cultivator Model HWC-243A Owner s Manual and Parts List SAVE THIS MANUAL You will need this manual for the safety instructions, assembly instructions and parts list. Put it in a safe, dry place
More informationModular XP Ramp Assembly Manual
Modular XP Manual 1 Contents Overview... 2-5 Section 1: 1.1 Tools required...6 1.2 Hardware list...6 Ramp & Platform Standard Parts 2.1 Ramp Parts...7 2.2 Platform Parts...8 2.3 Standard Platform Configurations...
More informationsouthpaw enterprises, inc.
Store these instructions in a safe place or with the enclosed maintenance checklist In-FUN-ity Climbing System Assembly Examples This example sheet is intended to supplement the instruction sheets that
More informationCertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS. Fence Installation Guide 3', 4' & 6' High
CertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS Fence Installation Guide 3', 4' & 6' High INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers
More informationInstallation Instructions Hustler 6-BTV Trap Vertical
Installation Instructions Hustler 6-BTV Trap Vertical ASSEMBLY 1. Check the package contents against the parts list on page 2. 2. WARNING. Installation of this product near power lines is dangerous. For
More informationCisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R)
Cisco Aironet Dual-Band MIMO Wall-Mounted Omnidirectional Antenna (AIR-ANT2544V4M-R) This document outlines the specifications for the Cisco Aironet 2.4-GHz/5-GHz Dual-Band MIMO Wall-Mounted Omnidirectional
More informationBASEBALL FOUL POLES GROUND SLEEVE MOUNTED
X X Page 1 of 6 GROUND SLEEVE INSTALLATION Ground Sleeve Foul Pole Size "A" F39901 32' and 40' 67 5/8" F39902 24' 67 5/8" F39903 16' 43 5/8" 00402000 12' 29 3/8" 7" ONE SET OF SLOTS MUST BE PARALLEL AND
More informationCONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013
U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -
More informationFS 5800 EXPANSION JOINT EJ FIRE BARRIER* Installation Instructions
Thermal Structures Inc. FS 5800 EXPANSION JOINT EJ FIRE BARRIER* Installation Instructions FLOOR TO FLOOR (F) ROOF TO ROOF (R) FLOOR TO WALL (FW) ROOF TO WALL (RW) WALL TO WALL (W) CORNER WALL (CW) FLOOR
More informationSDCS-03 DISTRIBUTION NETWORK GROUNDING CONSTRUCTION STANDARD (PART-II) OVERHEAD NETWORK GROUNDING. Rev. 01
SEC DISTRIBUTION GROUNDING STANDARD SDCS-03 Part-II Rev.01 SDCS-03 DISTRIBUTION NETWORK GROUNDING CONSTRUCTION STANDARD (PART-II) OVERHEAD NETWORK GROUNDING Rev. 01 This specification is property of SEC
More informationFlex Fence Instruction Manual
The Safer Stronger Smarter Choice Flex Fence Instruction Manual Table of contents 2 3 4 4 5 5 6 7 8 10 10 11 11 12 13 13 15 18 18 19 20 22 Table of contents Supplies, tools and equipment Introduction Laying
More informationInstallation Instructions for OPGW Bolted Dead End
INS-ACA015 OPGW Bolted Dead End Procedure 1. Disassemble dead end. Remove one bolt from the same side of each keeper. Loosen other bolts to permit conductor to be placed in the conductor groove. If keepers
More informationFENCING ASSEMBLY INSTRUCTIONS
1 SET POSTS Determine the post locations, 93" or 117" centers. Post spacing is flexible and can be decreased for terrain, etc. All posts should be set in concrete appropriate to local conditions.* POST
More informationREV: 1.2 TRAMPOLINE MANUAL
REV: 1.2 TRAMPOLINE MANUAL TRAMPOLINE PARTS LIST: Item 8FT 10FT 12FT 14FT 16FT A 1 1 1 1 1 B 1 1 1 1 1 C 6 8 12 12 12 E 48 64 72 96 108 F 6 8 12 12 12 G 3 4 6 6 6 H 12 16 24 24 24 I 1 1 1 1 1 DIAGRAMS
More information12'W x 10'H RoundTop Frame Assembly Please read and understand instructions completely before assembly.
12'W x 10'H RoundTop Frame Assembly Please read and understand instructions completely before assembly. Layout out frame parts as shown and match up items with quantity to make sure no parts are missing.
More informationPORT OF ST. HELENS SCAPPOOSE INDUSTRIAL AIRPARK PARALLEL TAXIWAY B RELOCATON AIP PROJECT ADDENDUM NO. 1
PORT OF ST. HELENS SCAPPOOSE INDUSTRIAL AIRPARK PARALLEL TAXIWAY B RELOCATON AIP PROJECT 3-41-0056-024-2018 ADDENDUM NO. 1 Addendum No. 1 hereby amends the contract documents and drawings for the Scappoose
More informationINSTALLATION INSTRUCTIONS FOR PLASCORE F5075 FRAME WALL
INSTALLATION INSTRUCTIONS FOR PLASCORE F5075 FRAME WALL The following information is provided by Plascore, Inc., as a general guideline for the installation of the F5075 Frame Wall System. This information
More informationYUKON PATIO COVER INSTALLATION INSTRUCTIONS
YUKON PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin: Consult your local building department for any required permits You may be required to obtain a building permit for this structure. Contact
More informationSPECIFICATIONS FOR THE INSTALLATION OF CONDUIT SYSTEMS IN RESIDENTIAL SUBDIVISIONS. Notification of Completed Conduit Sections
SPECIFICATIONS FOR THE INSTALLATION OF CONDUIT SYSTEMS IN RESIDENTIAL SUBDIVISIONS Section 1 Definitions 2 Scope of Work 3 Extent of Work 4 Inspection and Performance of Work 5 Trenching 6 Duct Installation
More informationInstallation Instructions. Tools Needed. Tape measure. Level. Shovel or Post hole digger. Concrete. Drill. Stakes. Mallet or hammer.
Installation Guide EcoStone Fence 1330 West 400 North Orem, UT 84057 Toll Free 1.866.648.9336 Tel. 1.801.655.5236 Fax 1.801.655.5240 www.ecostonefence.com Installation Instructions Introduction. These
More informationsouthpaw enterprises, inc.
southpaw enterprises, inc. Store these instructions with the enclosed maintenance checklist in a safe place. You may also access them on our website. Instruction Sheet Prefab Joist 3 Ft. Drop Ceiling Kit
More informationClearSpan PolyMax Windbreak Wall
ClearSpan PolyMax Windbreak Wall Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: February 2007ldg STK# DIMENSIONS
More informationINSTALLATION INSTRUCTIONS CHAIN-LINK FENCE AND GATE
INSTALLATION INSTRUCTIONS CHAIN-LINK FENCE AND GATE 1 BEFORE YOU START, IT S IMPORTANT TO CHECK......That fence footings do not exceed legally established property lines. If uncertain, refer to real estate
More informationFoundation Specifications for 5.6-Meter Modular Earth Station Antennas
Installation Instructions Bulletin 237029 Foundation Specifications for 5.6-Meter Modular Earth Station Antennas Revision A Introduction This document specifies typical foundation characteristics, designs,
More informationFoundation Specifications for 7.6-Meter Modular Earth Station Antennas
Installation Instructions Foundation Specifications for 7.6-Meter Modular Earth Station Antennas Bulletin 237186A Revision A Introduction This document specifies typical foundation characteristics, designs,
More informationFENCE INSTALLATION GUIDE 6 HIGH FENCE
FENCE INSTALLATION GUIDE 6 HIGH FENCE 1.866.648.9336 www.simtekfence.com INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers of SimTek decorative
More information1. ANSI/ASME Standard B , Square and Hex Bolts and Screws, Inch Series
SECTION 31 66 13 HELICAL PILES AND HELICAL ANCHORS PART 1 - GENERAL 1.1 DESCRIPTION A. This work pertains to furnishing and installing Helical Piles and Bracket Assemblies shown in the Contract in accordance
More information6o ft (18.3 m) Southwest Windpower, Inc West Route 66 Flagstaff, Arizona USA Phone: Fax:
6o ft (18.3 m) sectional MONOPOLE TOWER INSTALLATION MANUAL Southwest Windpower, Inc. 1801 West Route 66 Flagstaff, Arizona 86001 USA Phone: 928.779.9463 Fax: 928.779.1485 www.skystreamenergy.com 3-CMLT-1390-01
More informationTHIS SERVICE BULLETIN IS MANDATORY!
Service Bulletin No. LT20070717 Subject: Mast Support Guide Pin Model: LT-12D Product Group: Light Tower/Generator Date: July 17, 2007 SERVICE BULLETIN Group: LT THIS SERVICE BULLETIN IS MANDATORY! Series/Parts
More informationUSSC LLC 4 ONE LLC FIELD MODIFICATION INSTRUCTIONS
1 OF 17 A 1. PURPOSE: Instructions for in field replacement of 9004 mechanical suspension top pan 2. SCOPE: 9004 mechanical suspension with legacy two point LX back frame and current LX back frame 3. PROCEDURE:
More informationSection 808. FENCING
808.01 Section 808. FENCING 808.01. Description. This work consists of providing and erecting, or moving existing, woven wire fence, temporary fence, protective fence, chain link fence, high-tensile wire
More information6' x 8' x 6'6" Quad-Vent Greenhouse-in-a-Box Assembly Instructions
6' x 8' x 6'6" Quad-Vent Greenhouse-in-a-Box Assembly Instructions Description Model # 6' x 8' x 6'6" Quad-Vent Greenhouse-in-a-Box 70652 Recommended Tools Please read instructions COMPLETELY before assembly.
More informationInstruction Sheet RADIO FREQUENCY SYSTEMS. Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) No Rev.
Instruction Sheet No. 412764 Rev. B ECO 12469 Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) These Installation Instructions are valid for antennas in the following version: reflector 2.4
More informationFAQ ON EARTHING STANDARDS 16/08/2018
FAQ ON EARTHING STANDARDS 16/08/2018 This document has been updated to include changes made to substation earthing layouts that have been made necessary due to copper theft. The main changes to be aware
More informationWAL-MART SUPERCENTER # ; Milwaukie, OR: SPECIFICATIONS. Revisions to Specification Fence
MILWAUKIE OR #3144-00 ADDENDUM #5 NARRATIVE: 11-08-12 WAL-MART SUPERCENTER #3144-00; Milwaukie, OR: SPECIFICATIONS SPECIFICATIONS Revisions to Specification 02822 Fence Spec division 02822 has been revised
More informationTABLE OF CONTENTS REQUIRED TOOLS
TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS
More information22'W x 13'H Peak Style Shelter Frame Assembly Instructions
22'W x 13'H Peak Style Shelter Frame Assembly Instructions Recommended Tools Please read instructions COMPLETELY before assembly. This shelter MUST be securely anchored. THIS IS A TEMPORARY STRUCTURE AND
More informationLeveling Feet, Base Plates and Casters
Leveling Feet, Base Plates and Casters 77 Leveling Foot 1 1 Fastening to profile end Fastening in T-slot of profile For leveling tables and light equipment. Ratchet-type height adjustment requires no tools.
More informationInstallation Instructions for Bike Fixtation Public Work Stand and Floor Pump Manual RevH
Installation Instructions for Bike Fixtation Public Work Stand and Floor Pump Manual 311110 RevH Parallel Wall or object Setbacks: Both sides of the Public Work Stand should be at least 48 from walls or
More informationHOUSE PARTS PACKED IN HOUSE BOX PARTS IN PLASTIC BAG (HARDWARE) PARTS IN SMALL PLASTIC BAG (FLOOR CLIPS) PARTS PACKED IN BUNDLE
Check parts against this list before starting assembly. Refer to illustrations on pages 6 and 7 to view house parts. If any shortages are found, refer to Packing Slip for claim instructions. Item 3 5 6
More informationSAVVY OFF ROAD GAS TANK SKID INSTALLATION INSTRUCTIONS
It is best to work with a fuel tank that has the least amount of fuel in it as possible. Thank you for purchasing the best skid on the market. Please follow these instructions and your installation should
More informationTRANSACTION RECORD TR
COMMON GROUND ALLIANCE BEST PRACTICES COMMITTEE Proposal Form Revision to Best Practice Name: Ralph Graeser Date: 03/09/2015 Affiliation: PA PUC/NAPSR/GPTC Member. Phone: 717-554-3666 E-Mail: rgraeser@pa.gov
More informationINSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260
INSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260 I. SUSPENDED INSTALLATIONS NOTE: MODEL 260 FENSTEEL TRACK IS ASSEMBLED IN THE SAME MANNER AS DESCRIBED BELOW WITH THE EXCEPTION
More informationRaceline / Shockline/Endloop Installation Manual
Raceline / Shockline/Endloop Installation Manual Scan this QR code to watch the Installation Video. Trouble Shooting Hotline -800-878-5644 Flex Fence Raceline/Shockline Fence Installation Guide Before
More informationMidwest Roadside Safety Facility
B 64" 1626 602'-8 1/16" 183695 548'-0" 167030 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 373839 40 25 IMPACT 1500A 48" 12 27'-5" 8355 [] 3x7 CL A Galvanized
More informationINSTALLATION INTRUCTIONS
INSTALLATION INTRUCTIONS Page 1 of 9 Installation Instructions 1. 2. Check all items against parts list to ensure all parts have been included (see pages 6,7,8,9). Locate and drill holes for concrete footings.
More informationINSTRUCTION MANUAL. Model 18AVQII Five Band Vertical Antenna 10, 15, 20, 40, 80 Meter. General Description. Theory of Operation
Model 18AVQII Five Band Vertical Antenna 10, 15, 20, 40, 80 Meter 308 Industrial Park Road Starkville, MS 39759 (662) 323-9538 Fax: (662) 323-5803 INSTRUCTION MANUAL General Description The Hy-Gain 18AVQII
More informationCOMPONENTS INSTALLATION
PIPE BRACE ASSEMBLY - 8' FIXED-KNOT FENCE Brace posts... 14'x 2 7/8" Structural Tubing Cross Members... 10'x 2 3/8 Structural Tubing Angle Brace... 12'x 2 3/8 Structural Tubing Angle Brace Foot... 6' x
More informationELECTRIC SLIP ROLL MACHINE. Model: ESR-1300X2.5/ESR-1300X4.5 ESR-1550X3.5/ESR-1580X2.0
ELECTRIC SLIP ROLL MACHINE Model: ESR-1300X2.5/ESR-1300X4.5 ESR-1550X3.5/ESR-1580X2.0 Operation Manual Table of contents I MAIN SPECIFICATION...2 II SAFETY INSTRUCTIONS.. 2 III OPERATION INSTRUCTIONS..4
More informationHardware and Components:
Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut
More informationBLACK WIDOW COMPOSITE
PAGE-1 UPDATED 3-6-2015 REV.1 BLACK WIDOW COMPOSITE Detailed installation manual PAGE-2 UPDATED 3-6-2015 SpiderRax, Inc. REVISION PAGE Installation Manual For BWC-S, BWC-B,BWC-F DATE PAGES REASON OLD LEVEL
More informationPeak Style Shelter Assembly Instructions
6' x 10' x 6'6" Shed-in-a-Box Peak Style Shelter Assembly Instructions Description Model # 6' x 10' x 6'6" Shed-in-a-Box - Gray 70403 Recommended Tools Please read instructions COMPLETELY before assembly.
More informationAssembly Instructions for Key-Lock mechanical joints in sizes 2 to 40 inch ( mm)
Assembly Instructions for Key-Lock mechanical joints in sizes 2 to 40 inch (50-1000 mm) Introduction This guide provides recommendations for the installation of Bondstrand piping systems using the Key-Lock
More informationVentilation System. Installation Manual. Hog Slat Inc. Newton Grove, NC USA March
Installation Manual 1 Tunnel Door Framing Instructions It is import to make sure the Tunnel Door opening is flat and plumb. A maximum variation of +/- ½ throughout the length of the opening is acceptable.
More informationMARQUEE INSTALLATION HANDBOOK. Curved Structures
MARQUEE INSTALLATION HANDBOOK Curved Structures 12m Curved Roof Beam Assembly Instructions Ensure there are no overhead or underground obstructions or services before starting to assemble frame. Square
More informationCSS Central Mount System
CSS-20 Installation Manual CSS-20 Safety Notifications Below are the installation instructions for the CSS-20-2 Long Span Beam Mounting System. Please read these safety notifications prior to beginning
More informationDowntown Rack. Custom logo option available
Custom logo option available Downtown Rack The Downtown Rack uses thick, square-tube construction that can t be cut with a pipe cutter. The extended width of the Downtown Rack makes for easy bike parking
More information26 GARDEN CART ASSEMBLY & OPERATING INSTRUCTIONS. Rev 07/03
GARDEN CART 304 ASSEMBLY & OPERATING INSTRUCTIONS 3 Rev 07/03 THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner s record below: Model Serial No. Purchase
More informationOxford Stalls Installation Instructions
Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or
More informationThe Queen Quilter Professional Quilters Kit Frame
The Queen Quilter Professional Quilters Kit Frame Assembly Instructions Table of Contents: Before you begin......................... Pg. 2 Wood parts............................. Pg. 3 Hardware..............................
More informationAC Voltage- Pipeline Safety and Corrosion MEA 2015
AC Voltage- Pipeline Safety and Corrosion MEA 2015 WHAT ARE THE CONCERNS ASSOCIATED WITH AC VOLTAGES ON PIPELINES? AC concerns Induced AC Faults Lightning Capacitive coupling Safety Code Induced AC Corrosion
More informationThe Nantucket Legacy Arbor
ASSEMBLY INSTRUCTIONS 0. in 9 in 0. in 68 in 7 in in *Nantucket Legacy with Trim Kit Shown Above. Please read through before starting assembly. in 60 in 0 in 8 in IMPORTANT: CHECK THE INSIDE OF YOUR POSTS
More informationInstalling a COMROD AS1R Whip Antenna with Anchor Post
Installing a COMROD AS1R Whip Antenna with Anchor Post IS10012 Issue 1.0...15 September 2010 Nautel Limited 10089 Peggy's Cove Road, Hackett's Cove, NS, Canada B3Z 3J4 T.877 6 nautel (628835) or +1.902.823.2233
More informationCONTINUING EDUC ATION
3 CONTINUING EDUC ATION FOR WISCONSIN ELECTRICIANS 2017 NEC Article 250 2 Hours WISCONSIN CONTRACTORS INSTITUTE N16 W23217 Stone Ridge Drive Suite 290 Waukesha, WI 53188 262-409-4282 www.wcitraining.com
More informationAssembly Instructions
8' x 6' x 6'6" Professional Growers Greenhouse Assembly Instructions Description Model # 8' x 6' x 6'6" Professional Growers Greenhouse PGG68 350351 Please read instructions COMPLETELY before assembly.
More informationBASEBALL FOUL POLES SURFACE MOUNTED
Page 1 of 5 Installation Instructions 1. 2. Check all items against parts list to ensure all parts have been included. Locate and drill holes for concrete footings. See Details A and B for critical information
More informationDublin Stalls Installation Instructions
Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round
More informationCAMSPAN GALLERY CONVEYORS INSTALLATION & ERECTION GUIDELINES
CAMSPAN GALLERY CONVEYORS INSTALLATION & ERECTION GUIDELINES JANUARY, 1998 Cambelt International Corporation 2820 West 1100 South Salt Lake City, Utah 84104 Phone(801) 972-5511 Fax(801) 972-5522 www.cambelt.com
More informationASSEMBLY GUIDE. Barcelona Pergola. 12 X16 (365CMx487CM) VER /01/19
ASSEMBLY GUIDE Barcelona Pergola 12 X16 (365CMx487CM) VER 1.9 04/01/19 GETTING STARTED First off, allow us to say thank you for the investment you have made in our fine pergola. This pergola is designed
More informationI-W07/W77. Couplings DETAIL A WARNING. Photo Showing Pipe with Weld Seam Ground 6 inches/152 mm Back from Pipe End and an AGS Groove
WARNING Read and understand all instructions before attempting to install any Victaulic piping products. These products must be used only on pipe that is prepared to Victaulic Advanced Groove System (AGS)
More informationATLANTIS RAIL Contact Information
ATLANTIS RAIL Contact Information Customer Service (800) 541-6829 (508) 732-9191 Spectrum System Installation Instructions Atlantis Rail s Spectrum System is an easy to install, universal cable railing
More informationX-TENSION 350 Guardrail End Terminal Tangent and Flared
X-TENSION 350 Guardrail End Terminal Tangent and Flared December 2015 Table of Contents Introduction 3 System Overview 3 Before Installation 3 Limitations and Warnings 4 Safety Statements 4 Parts Identification
More informationInstallation Instructions for: Saris Cycle Aid. Saris Cycle Air. Saris Cycle Air HD
Installation Instructions for: Saris Cycle Aid Saris Cycle Air Saris Cycle Air HD A. Setbacks Parallel Wall or object Setbacks: Both sides of the Saris Cycle Aid should be at least 48 from walls or other
More informationEraser Conveyor Belt Cleaning System IWARNING Always obey all applicable safety rules. Be sure all power to the conveyor has been disconnected and con
INSTALLATION GUIDE LIB-CP-REA-03-01 Rev. 10 Eraser Conveyor Belt Cleaning System ARGONICS Eraser Conveyor Belt Cleaning System IWARNING Always obey all applicable safety rules. Be sure all power to the
More information1.8 METER SERIES 1184 ANTENNA SYSTEM
REVISION F January 10, 2002 ASSEMBLY MANUAL 1.8 METER SERIES 1184 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1184 ANTENNA SYSTEM F Revised Address 1/10/02
More informationArt Thatch TM Umbrella Kit Installation Guide
Art Thatch TM Umbrella Kit Installation Guide www.artificialthatch.com (858) 643-9030 sales@artthatch.com Parts List Part # Description Name Qty. #1 Main Frame 1 #2 Small Cross Bar 8 #3 Medium Cross Bar
More information