Apitech Valve Drive Board

Size: px
Start display at page:

Download "Apitech Valve Drive Board"

Transcription

1 M511 Apitech Valve Drive Board Completely Independent Adjustments Current Sourcing PWM Outputs 2 Current Ranges, MID and HI ma PWM Current Range Independent HIA and HIB adjustments Adjustable MID and LO currents Adjustable Ramp 0-5 seconds 3 Auxiliary Outputs Amp Current Rating Over-Signal and Short Circuit Protected The M511 Series Valve Drive Boards are designed specifically to drive Apitech valves. The boards have five adjustments that are factory pre-set to Apitech specifications. These are as follows: Lo, Mid, HiA, HiB, and Ramp. Further adjustments can be made with five trimpots. The adjustments are totally independent of one another, making calibration much easier than on similar products. The M511 series is epoxy encapsulated for superior environmental protection. M511s are compliant with CE labeling requirements. Parameter Min Typical Max Units Operating Temperature Range C Power Supply Minimum 8.0 VDC Maximum 32 VDC Transient Reverse Polarity 400 VDC Current at Null 30 ma Regulated Voltage Minimum VDC Maximum VDC Current Output 100 ma Signal Input Input Resistance 20K Ω Input Null 2.5 VDC Input (Referred to GND) VDC Over signal Max 4.3 VDC Over signal Min 0.7 VDC Signal Range Inputs Input Type Switch to Vs for High Range Input Current 4 ma Max Input Voltage 32 V Minimum Input Voltage 6 VDC Trip Point - Reset Point - PWM Outputs Frequency Hz

2 Frequency Tolerance 10 % Minimum Duty Cycle (Adjustable) % Maximum Duty Cycle (Adjustable) % Short Circuit Current Limit 1.5 Amps Voltage Drop at Max Current VDC Max Voltage 200 V Max Reverse Voltage 32 V Linearity 1 % A and B Auxiliary Outputs Signal Trip Point A( Referred to GND) 2.8 VDC Signal Trip Point B (Referred to GND) 2.2 VDC Max Current 1.5 Amps Short Circuit Current Limit Thermal Voltage Drop at Max Current VDC Max Voltage 200 VDC Max Reverse Voltage 32 VDC Common Auxiliary Output Signal Trip Point(Referred to GND) VDC Max Current 1.5 Amps Short Circuit Current Limit Thermal Voltage Drop at Max Current VDC Max Voltage 200 VDC Max Reverse Voltage 32 VDC Timing and Delays Power Up Delay (PWM Output) 100 ms Power Off Delay (PWM Output) 0 Signal On Delay (Full Scale PWM Output) 1 ms Signal Off Delay (Full Scale PWM Output) 1 ms 2 Ramp EMC Ramp Range 0 5 Sec Asymmetry 1 Sec IEC (Radiated Susceptibility) 30 V/m IEC (Conducted Susceptibility) Operational Considerations: Supply Requirements: The M511 has been designed to accept a wide range of supply voltages. The board is capable of functioning properly when supplied with a DC voltage ranging from 8 volts to 32 volts. To ensure proper operation, the ripple should be limited to less than 15% of the supply voltage. Remember that the M can source as much as 4 amps from Vs with three outputs active. Vs and GND wiring should be sized appropriately to handle this type of load.

3 3 Signal Input: ** The signal input is a relatively low impedance input at 20K ohms. It is generally driven with a 500 ohm potentiometer and 180 ohm resistors, connected between PT+ and PT-. This will provide a varying signal at the wiper that is equal to 2.5 Volts at center, and change between 1 VDC and 4 VDC depending on the direction of rotation. However, the input can be driven with any DC source capable of supplying 2.5 VDC at neutral, and 1 VDC for full output in the B direction, and 4 VDC for full output in the A direction. For short lead lengths, shielded cable is not required. However for longer runs in noisy environments, shielded cable is recommended. For best performance, connecting the shield at the valve drive board to ground is appropriate. PWM Outputs: The PWM outputs are voltage sourcing outputs. The outputs are implemented as a high current, bipolar (Darlington) switch connected to Vs. The PWM outputs employ a crowbar type current limit circuit to shut down the outputs above 1.5 Amps. This provides plenty of design margin for Apitech valves which generally source under 400 ma at full flow and 12 VDC. The board is designed as to provide a pulse width modulated output at 33 Hz. The pulse width can be adjusted from a duty cycle of 10 to 95 %. The PWM outputs may be tied together to form a flow control type of configuration with no adverse operational effects.

4 4 Linearity: The input voltage vs. output duty cycle is excellent over all operating conditions. M511 input vs. output linearity signal voltage duty cycle RDC MID Range: Ramp: As the output duty cycle is changed by the HI potentiometer, there is a second selectable gain range, called MID. MID operates exactly like the HI pot, when the HI ENABLE input is not connected to Vs. If HI ENABLE is connected to Vs, the output will range between the LO trim pot setting, and the HI trim pot setting. When the HI ENABLE is not connected to Vs, the output will range between the LO trim pot setting and the MID trim pot setting. The HI ENABLE input basically selects the gain of the valve drive board as set by the trim pots. This allow the user to have a coarse and a fine control of the output. Ramp is basically a limiting of the bandwidth of the signal channel. When ramp is set to off, the output responds immediately to the input signal. When ramp is set to the maximum setting, the output will take 5 seconds to ramp from the LO set point to the HI set point, or the MID set point, depending on which range is selected. However, if the HI ENABLE input changes state while the valve drive board is generating a PWM signal, the output will immediately seek the new output value, regardless of ramp value. The graph below shows the ramp linearity and symmetry:

5 5 DATA VOLT SUPPLY 5/14/ VOLTAGE SECONDS HIA and HIB: PT+ and PT-:** Making Adjustments: Auxiliary Outputs: The valve drive board has independent HI adjustments for the A direction and the B direction. The PT+ and PT- outputs are intended to be connected to a 500 ohm potentiometer and 180 ohm resistors. PT+ is connected internally to 5 volts. The PT- is connected to GND. When connected across a 500 ohm network, the voltage at PT+ will provide full signal output in the A direction, and the voltage at PT- will cause full signal output in the B direction. The trim pots exhibit an extremely low dependence on one another. While the most of the trip pots are completely independent of each other, the LO pot does cause a minor change in the HI settings. For this reason, it is prudent to set the LO trim pot first and then set the others. The Auxiliary outputs are protected with a thermal shutdown technique. In the event of a short circuit, the output will not reset to normal operation unless the short has been removed, and either the power cycled or the joystick returns to neutral.

6 6 Dimensions: All Mounting holes are #6 clearance holes, in 4 places. Brackets are available for vertical mounting of assembly. P/N B is a bracket that picks up the four mounting holes of the valve drive board and converts them for mounting the assembly standing up. The bracket is shown below: Mating Connectors: The connector used on the M511 series is a PCD #ELFH There are a range of mating connectors available from PCD, Phoenix Contact, Beau, LMI, AMP and Weimeuller. P-Q Controls can supply a limited selection of mating PCD connectors at an additional charge. P-Q part number A for 11 position connector.

7 7 Ordering Information: **M511 **M511IND No Lead Protection, Potentiometer Command With Lead Protection, Potentiometer Network Command, Model 212, 215 & 220 Controlled STANDARD WHEN USED WITH P-Q CONTROLS JOYSTICKS M511IND-XX-X Auxiliary Output Options Mid Range 02 none M Mid Range 03 A and B Auxiliary 10 Common Auxiliary 11 Common, A and B Auxiliaries Revised for the Sales Dept Rev B. 8/02/2001, HGK M511 VDB Specifications.doc

8 8 Typical Connections: M511 IND M511

Digital Interface Card DEC005000

Digital Interface Card DEC005000 Engineering & Manufacturing Solutions Digital Interface Card DEC005000 APPLICATION: The DEC005000 conveniently interfaces industry standard signals 4-20mA, 0-5V or 0-10V with a proportional solenoid valve

More information

Sealed Interface Control: EC20300

Sealed Interface Control: EC20300 ISO 9001:2000 WITH DESIGN Certificate #02.002.1 Sealed Interface Control: EC20300 FEATURES: Weather tight control package Pulse Width Modulated output Waterproof altitude pressure and vapor release vent

More information

Brushless DC Motor Controller Specification Assemblies 025F0248

Brushless DC Motor Controller Specification Assemblies 025F0248 Brushless DC Motor Controller Specification Assemblies 025F0248 600A1099 Rev. B April 4 th, 2014 Revision History EC Date Description Rev EC54318 09/03/13 Initial Release A EC58093 04/04/14 Added cap discharge

More information

These power supplies are ideal for telecom, datacom, industrial equipment and other applications.

These power supplies are ideal for telecom, datacom, industrial equipment and other applications. The ABC350 Series of open frame power supplies feature a wide universal AC input range of 90 264 VAC, offering 350 W of output power in a compact 3 x 5 x 1 inch footprint, with a variety of isolated single

More information

DeviceCraft Revision #1 11/29/2010

DeviceCraft Revision #1 11/29/2010 DeviceCraft Revision #1 11/29/2010 DC Wiper Motor H-Bridge Servo / Speed Controller P/N 1020 Features: Dip Switch selectable mode of operation Both PID servo or speed controller Forward/Reverse operation

More information

WESTREX RA-1712 PHOTOGRAPHIC SOUND RECORD ELECTRONICS

WESTREX RA-1712 PHOTOGRAPHIC SOUND RECORD ELECTRONICS INTRODUCTION The RA-1712 solid state Record Electronics is an integrated system for recording photographic sound tracks on a Westrex photographic sound recorder. It accepts a 600Ω input signal level from

More information

Analog Servo Drive 25A20DD

Analog Servo Drive 25A20DD Description Power Range NOTE: This product has been replaced by the AxCent family of servo drives. Please visit our website at www.a-m-c.com or contact us for replacement model information and retrofit

More information

Anacon Power & Controls

Anacon Power & Controls 2254 Main Street, Concord, MA 01742-3829 Tel: 800-466-9080 978-287-0715 Fax: 978-287-0952 www.anaconpower.com sales@anaconusa.com SCR Power Controllers Zero Cross Time Based / Burst Fire C - SCR (Burst)

More information

P/N: AX TECHNICAL DATASHEET #TDAX Single Input, Dual Output Valve Controller 1 Universal Input, +5V reference CAN (SAE J1939)

P/N: AX TECHNICAL DATASHEET #TDAX Single Input, Dual Output Valve Controller 1 Universal Input, +5V reference CAN (SAE J1939) TECHNICAL DATASHEET #TDAX022000 Single Input, Dual Output Valve Controller 1 Universal Input, +5V reference (SAE J1939) Features: 1 universal signal input 2 proportional or on/off outputs up to 3 A User

More information

HAU Series Controllers

HAU Series Controllers Instruction, Installation and Operation Guide for: HAU Series Controllers Document Number: 021-00140 Document Revision: B.2 Document Issue Date: Document Creator: G.Gotting Document Creation Date: 4/21/2011

More information

ISO 9001 CERTIFIED. 607 NW 27th Ave Ocala, FL Phone: (352) or Fax: (352) OPERATION MANUAL

ISO 9001 CERTIFIED. 607 NW 27th Ave Ocala, FL Phone: (352) or Fax: (352) OPERATION MANUAL ISO 9001 CERTIFIED Phone: (352) 629-5020 or 800-533-3569 Fax: (352)-629-2902 ES-Key 12 PDM module (4 selectable polarity outputs) with 4 Inputs (selectable polarity) and 4 MFI Inputs P/N 610-00035 PAGE

More information

Potentiometer Control EC20200

Potentiometer Control EC20200 Engineering & Manufacturing Solutions Potentiometer Control EC20200 APPLICATION: Proportionally control the speed of hydraulic motors and cylinders. ISO 9001:2008 WITH DESIGN Certificate #02.002.1 Features

More information

1525-BRS INFORMATION MANUAL SERV O D YN A M ICS. D y n ad r iv e Ave Crocker Suite 10 Valencia, CA

1525-BRS INFORMATION MANUAL SERV O D YN A M ICS. D y n ad r iv e Ave Crocker Suite 10 Valencia, CA 28231 Ave Crocker Suite 10 Valencia, CA 91355 818-700-8600 Servodynamics.com INFORMATION MANUAL 1525-BRS SERV O D YN A M ICS U SA www.servodynamics.com D y n ad r iv e Bru sh INDEX Page INTRODUCTION 2

More information

Thornwood Drive Operating Manual: Two-SCR General Purpose Gate Firing Board FCRO2100 Revision H

Thornwood Drive Operating Manual: Two-SCR General Purpose Gate Firing Board FCRO2100 Revision H http://www.enerpro-inc.com info@enerpro-inc.com 5780 Thornwood Drive Report R188 Goleta, California 93117 February 2011 Operating Manual: Two-SCR General Purpose Gate Firing Board FCRO2100 Revision H Introduction

More information

TECHNICAL DATASHEET #TD1400AX PWM Controlled Solenoid Driver (DIN rail mount) P/N: PWMC-DR-2A, PWMC-DR-1.2A

TECHNICAL DATASHEET #TD1400AX PWM Controlled Solenoid Driver (DIN rail mount) P/N: PWMC-DR-2A, PWMC-DR-1.2A TECHNICAL DATASHEET #TD1400AX PWM Controlled Solenoid Driver (DIN rail mount) P/N: PWMC-DR-2A, PWMC-DR-1.2A Description: The PWM Controlled Solenoid Driver supplies a proportional solenoid with current

More information

TECHNICAL DATASHEET #TDAX INPUTS, 5 OUTPUTS VALVE CONTROLLER

TECHNICAL DATASHEET #TDAX INPUTS, 5 OUTPUTS VALVE CONTROLLER TECHNICAL DATASHEET #TDAX020510 6 INPUTS, 5 OUTPUTS VALVE CONTROLLER Up to 6 Digital, Analog or PWM Command Inputs 5 Independent Proportional or On/Off Outputs 1 +5V, 100 ma Reference Voltage CAN (SAE

More information

with Electronic Assistant

with Electronic Assistant Description: The quad valve controller provides precise, repeatable control of 4 proportional solenoids and 1 on/off solenoid over a SAE J1939 network. PWM signal inputs or analog voltage or current inputs

More information

VISION HISTORY Rev Level Rev Date Change Made Reason for Change Effective Approved By A 11/11/13 Specification Release S. Sadot A1 14/01/14 Update ope

VISION HISTORY Rev Level Rev Date Change Made Reason for Change Effective Approved By A 11/11/13 Specification Release S. Sadot A1 14/01/14 Update ope Electrical Specification for: Compact PCI - 6U - AC - 700W Telkoor Part Number: 900-7802-0000 SCALE RELEASE DATE 11/11/13 SHEET 1 OF 7 VISION HISTORY Rev Level Rev Date Change Made Reason for Change Effective

More information

WATT TRANSDUCER. Instruction Manual

WATT TRANSDUCER. Instruction Manual WT 9200 WATT TRANSDUCER Instruction Manual IM-2 September 2003 USA: 6428 Ridglea Drive, Watauga, Texas 76148 Tel/Fax 1-817-427-2060/2067 E-mail: wes@westecinstruments.com SPECIFICATIONS Power Supply Input

More information

5 x 3 x 0.75 Inches form factor. 275 Watts with Forced Air Cooling. Efficiencies up to 92% Standby Power < 0.5 W

5 x 3 x 0.75 Inches form factor. 275 Watts with Forced Air Cooling. Efficiencies up to 92% Standby Power < 0.5 W The ABC275 Series of ultra low profile open frame power supplies feature a wide universal AC input range of 80 264 VAC, offering output power 275 W with 13 CFM forced air cooling, or up to 160 W with convection

More information

815-BR SERVO AMPLIFIER FOR BRUSH SERVOMOTORS

815-BR SERVO AMPLIFIER FOR BRUSH SERVOMOTORS 815-BR SERVO AMPLIFIER FOR BRUSH SERVOMOTORS USER GUIDE September 2004 Important Notice This document is subject to the following conditions and restrictions: This document contains proprietary information

More information

MDSD (Series 2X) Mobile Dual Solenoid Driver

MDSD (Series 2X) Mobile Dual Solenoid Driver R 64/. MDSD (Series X) Mobile Dual Solenoid Driver R 64/.5 Replaces: 6.4 The MDSD amplifier provides control of components that use proportional solenoids without LVDTs for actuation. The MDSD orporates

More information

DynaDrive INFORMATION MANUAL SDFP(S)

DynaDrive INFORMATION MANUAL SDFP(S) DynaDrive INFORMATION MANUAL SDFP(S)1525-17 SERVO DYNAMICS CORP. 28231 Avenue Crocker, Santa Clarita, CA. 91355 (818) 700-8600 Fax (818) 718-6719 www.servodynamics.com INDEX Page INTRODUCTION 2 ELECTRICAL

More information

Jaguar Motor Controller (Stellaris Brushed DC Motor Control Module with CAN)

Jaguar Motor Controller (Stellaris Brushed DC Motor Control Module with CAN) Jaguar Motor Controller (Stellaris Brushed DC Motor Control Module with CAN) 217-3367 Ordering Information Product Number Description 217-3367 Stellaris Brushed DC Motor Control Module with CAN (217-3367)

More information

Installation, Operation and Maintenance Manual

Installation, Operation and Maintenance Manual NIAGARA M513 Rev. B Model 1005 Pulse to DC Converter Installation, Operation and Maintenance Manual Table of Contents General... 1 Specifications... 1 Installation... 1 Theory of Operation... 2 Setup...

More information

User s Manual for Integrator Short Pulse ISP16 10JUN2016

User s Manual for Integrator Short Pulse ISP16 10JUN2016 User s Manual for Integrator Short Pulse ISP16 10JUN2016 Specifications Exceeding any of the Maximum Ratings and/or failing to follow any of the Warnings and/or Operating Instructions may result in damage

More information

CAP6637A AC-DC Open Loop Converter

CAP6637A AC-DC Open Loop Converter Description: The CAP6637 is a three-phase AC to DC Converter assembly. The assembly includes the three-phase SCR converter bridge, a free wheeling diode, the thermal management system, a BAP1950 SCR phase

More information

TECHNICAL DATASHEET #TDAX Universal Input, Single Output Valve Controller CAN (SAE J1939)

TECHNICAL DATASHEET #TDAX Universal Input, Single Output Valve Controller CAN (SAE J1939) Features: TECHNICAL DATASHEET #TDAX021610 Universal Input, Single Output Valve Controller CAN (SAE J1939) 1 universal signal input (voltage, current, resistive, PWM, frequency or digital) 1 output: proportional

More information

FEATURES OPTIONAL FEATURES

FEATURES OPTIONAL FEATURES -00--0 B Series The Assured Automation B Series electric valve actuators offer a rugged design for quarter turn industrial applications. Designed for use on quarter turn (0 ) ball valves, butterfly valves,

More information

Model 25A Manual. Introduction:

Model 25A Manual. Introduction: Model 25A Manual Introduction: The Model 25A drive electronics is a high voltage push-pull linear power amplifier capable of output voltage swings in the order of 145v P-P, push-pull. The Model 25A provides

More information

AMC-100 AMC-101 AMC-100 AMC-100B AMC-100D AMC-101 AMC-101B AMC-101D AMC-100A AMC-100C AMC-100E AMC-101A AMC-101C AMC-101E. AC Motor Controllers

AMC-100 AMC-101 AMC-100 AMC-100B AMC-100D AMC-101 AMC-101B AMC-101D AMC-100A AMC-100C AMC-100E AMC-101A AMC-101C AMC-101E. AC Motor Controllers The Indelac / AC Motor Controllers are used for proportional positioning of split phase AC actuator motors. An external command signal of 0-0V, -V, or -0mA can be used to compare to a feedback signal from

More information

Ametek, Inc. Rotron Technical Products Division. 100 East Erie St., Suite 200 Kent, Ohio User's Guide. Number Revision F

Ametek, Inc. Rotron Technical Products Division. 100 East Erie St., Suite 200 Kent, Ohio User's Guide. Number Revision F Ametek, Inc. Rotron Technical Products Division 100 East Erie St., Suite 200 Kent, Ohio 44240 User's 120 Volt, 800 Watt and 240 Volt, 1200 Watt Brushless Motor Drive Electronics 5.7" (145 mm) and 7.2"

More information

Thornwood Drive Operating Manual: Six-SCR General Purpose Gate Firing Board FCOG6100 Revision R

Thornwood Drive Operating Manual: Six-SCR General Purpose Gate Firing Board FCOG6100 Revision R http://www.enerpro-inc.com info@enerpro-inc.com 5780 Thornwood Drive Report R380 Goleta, California 93117 June 2008 Operating Manual: Six-SCR General Purpose Gate Firing Board FCOG6100 Revision R Introduction

More information

BENCHMARK MEDIA SYSTEMS, INC.

BENCHMARK MEDIA SYSTEMS, INC. BENCHMARK MEDIA SYSTEMS, INC. PPM-1 Meter Card Instruction Manual 1.0 The PPM... 1 1.1 The PPM-1... 1 2.1 Measurement Conventions... 1 2.2 System References... 2 3.0 Connections to the PPM-1 Card... 2

More information

P/N: AX Applications: Off-highway construction equipment Municipal vehicles. Ordering Part Numbers:

P/N: AX Applications: Off-highway construction equipment Municipal vehicles. Ordering Part Numbers: Features: Command messages are received through the CAN network (no physical inputs) 10 universal outputs of up to 2.5A are user selectable from the following types (up to a maximum of 7A of controller

More information

TECHNICAL DATASHEET #TDAX INPUT, 12 OUTPUT VALVE CONTROLLER,

TECHNICAL DATASHEET #TDAX INPUT, 12 OUTPUT VALVE CONTROLLER, TECHNICAL DATASHEET #TDAX020400 12 INPUT, 12 OUTPUT VALVE CONTROLLER, Multi-functional 7 Signal and 5 Digital Inputs 8-2.5A Proportional and 4-3A On/Off Outputs 1 +5V, 100 ma Reference Voltage CAN (SAE

More information

These power supplies are ideal for medical, telecom, datacom, industrial equipment and other applications.

These power supplies are ideal for medical, telecom, datacom, industrial equipment and other applications. The ABC550 Series of open frame power supplies feature a wide universal AC input range of 90 264 VAC, offering up to 550 W of output power with forced air cooling, or 250 W with conduction cooling in a

More information

MCHXXX. Simple to install MECHANICAL. HANDLE STROKE ± 30 (60 total travel)

MCHXXX. Simple to install MECHANICAL. HANDLE STROKE ± 30 (60 total travel) DESCRIPTION The MCHXXX Control Handle is intended for open-loop control of electrohydraulic proportional valves utilizing pulse width modulated (PWM) outputs to optimize valve performance. Adjustments

More information

HB-25 Motor Controller (#29144)

HB-25 Motor Controller (#29144) Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267

More information

Pin-Out Information Pin Function. Inhibit (30V max) Pkg Style 200

Pin-Out Information Pin Function. Inhibit (30V max) Pkg Style 200 PT6 Series Amp Adjustable Positive Step-down Integrated Switching Regulator SLTS29A (Revised 6/3/2) 9% Efficiency Adjustable Output Voltage Internal Short Circuit Protection Over-Temperature Protection

More information

Rev.8 03/08 SSRMAN-1P SERIES USERS MANUAL SSR INTELLIGENT PHASE ANGLE CONTROL MODULE COPYRIGHT 2008 NUWAVE TECHNOLOGIES, INC.

Rev.8 03/08 SSRMAN-1P SERIES USERS MANUAL SSR INTELLIGENT PHASE ANGLE CONTROL MODULE COPYRIGHT 2008 NUWAVE TECHNOLOGIES, INC. Rev.8 03/08 MAN-1P SERIES USERS MANUAL INTELLIGENT PHASE ANGLE MODULE COPYRIGHT 2008 MAN-1P Users Manual Page 2 TABLE OF CONTENTS 1. Ordering Codes... 2 2. Description... 2 2.1 Features... 3 3. Installation...

More information

S1 Programming Chart Program Description S1 Switch Positions. Constant ON High/Low Track, WR

S1 Programming Chart Program Description S1 Switch Positions. Constant ON High/Low Track, WR RODIX INC. FEEDER CUBE FC90 Plus Series ADVANCED FEATURES Optional software features of the 24490 / 2449 circuit boards OVERVIEW: The FC90 Plus Series of feeder controls are built around the circuit boards

More information

DC-DC Converter Module

DC-DC Converter Module Features DC input range: 27-56 V Input surge withstand: 105 V for 100 ms DC output: 13.4 V Programmable output: 10 to 110% Regulation: ±0.2% no load to full load Efficiency: 88.5% Maximum operating temperature:

More information

American Power Design, Inc.

American Power Design, Inc. FEATURES 4 Customer Selects Output Voltage 4 Fully Regulated Outputs to + or - 8000 Vdc 4 0-100% Programable Output 4 High Stability (

More information

Applications: oil and gas equipment automation; off-highway machine automation; agricultural equipment

Applications: oil and gas equipment automation; off-highway machine automation; agricultural equipment Features: 6 Universal Signal Inputs are user configurable as: o 0-5V, 0-10V, 4-20mA or 0-20mA o 20Ω to 250 kω Resistive o 1 Hz to 10 khz PWM o Digital o Three of the inputs can be configured as a pulse

More information

with Electronic Assistant

with Electronic Assistant TECHNICAL DATASHEET #TDAX021300 Valve Controller 6 On/Off P/N: AX021300 2 Analog and 3 Frequency Command Inputs 6 On/Off Outputs (Option: PWM) CAN (SAE J1939) with Electronic Assistant Features: 2 user

More information

PDO 2035 Stepper Drive with Digital Oscillator

PDO 2035 Stepper Drive with Digital Oscillator 44 Westridge Dr. Watsonville, CA 9576 831/761-6555 8/525-169 FAX 831/761-6544 PDO 235 Stepper Drive with Digital Oscillator PDO 235 Packaged Pulse and Direction Step Motor Drive with Digital Oscillator

More information

Precision Voltage Control System

Precision Voltage Control System 1.800.61.8754 Precision Voltage Control System The PVCS is a driver controller module with many powerful features that can be easily programmed for use with many applications such as speed and directional

More information

CA SERIES PRECISION REGULATED, LOW RIPPLE HIGH VOLTAGE DC TO DC CONVERTERS

CA SERIES PRECISION REGULATED, LOW RIPPLE HIGH VOLTAGE DC TO DC CONVERTERS Proven Reliability CA SERIES PRECISION REGULATED, LOW RIPPLE HIGH DC TO DC CONVERTERS 200V to 2000V @ Watt PRODUCT SELECTION TABLE NOW UL RECOGNIZED PRODUCT DESCRIPTION Precision regulated, very low noise,

More information

PEAKTRONICS AMC-103 ADDITIONAL FEATURES. AC Motor Controller, 2A AMC-103 AMC-103A AMC-103B

PEAKTRONICS AMC-103 ADDITIONAL FEATURES. AC Motor Controller, 2A AMC-103 AMC-103A AMC-103B PEAKTRONICS The Peaktronics AC Motor Controller is a compact module that is intended for controlling small AC actuator motors of up to 2A. The is very well suited for applications where space constraints

More information

Variable Speed Brushed DC Motor Drive

Variable Speed Brushed DC Motor Drive The driving force of motor control & electronics cooling. Equinox: Variable Speed Brushed DC Motor Drive Navigator Equinox The Equinox variable speed brushed DC motor drive with Navigator Programmer is

More information

TECHNICAL DATASHEET #TDAX A DC MOTOR CONTROLLER P/N: AX Variable Speed Control, Onboard I/O CAN SAE J1939, Rugged Packaging

TECHNICAL DATASHEET #TDAX A DC MOTOR CONTROLLER P/N: AX Variable Speed Control, Onboard I/O CAN SAE J1939, Rugged Packaging TECHNICAL DATASHEET #TDAX102000 35A DC MOTOR CONTROLLER P/N: AX102000 Variable Speed Control, Onboard I/O CAN SAE J1939, Rugged Packaging with Electronic Assistant Features: Unidirectional or bi-directional

More information

Coils & Electronic Controls

Coils & Electronic Controls HYDRAFORCE Coils & Electronic Controls COILS FOR SOLENOID OPERATED VALVES Standard Coils and Proportional Valve Coils... 3.200.1 Series E Water/Weather Resistant Coils... 3.400.1 ELECTRONIC CONTROLS FOR

More information

Analog Servo Drive 30A8

Analog Servo Drive 30A8 Description Power Range The 30A8 PWM servo drive is designed to drive brush type DC motors at a high switching frequency. A single red/green LED indicates operating status. The drive is fully protected

More information

PRELIMINARY. Preliminary TECHNICAL DATASHEET #TDAX DC MOTOR CONTROLLER P/N: AX100650

PRELIMINARY. Preliminary TECHNICAL DATASHEET #TDAX DC MOTOR CONTROLLER P/N: AX100650 Preliminary TECHNICAL DATASHEET #TDAX100650 DC MOTOR CONTROLLER P/N: AX100650 Variable Speed Control, Onboard Inputs 6A DC Motor Output, 2.5A Proportional Output, 2 Signal Outputs CAN SAE J1939, Rugged

More information

Figure 1. DMC 60 components.

Figure 1. DMC 60 components. 1300 Henley Court Pullman, WA 99163 509.334.6306 www.digilentinc.com DMC 60 Reference Manual Revised November 15, 2016 This manual applies to the DMC 60 rev. A Overview The DMC 60 is an electronic speed

More information

Peak Current. Continuous Current. See Part Numbering Information on last page of datasheet for additional ordering options.

Peak Current. Continuous Current. See Part Numbering Information on last page of datasheet for additional ordering options. Description Power Range The PWM servo drive is designed to drive brushless DC motors at a high switching frequency. A single red/green LED indicates operating status. The drive is fully protected against

More information

This convection-cooled series is designed for use in commercial and industrial environments in temperatures up to 50 C.

This convection-cooled series is designed for use in commercial and industrial environments in temperatures up to 50 C. RoHS Lead-Solder-Exemption Compliant Automatic 115/230 Input Voltage Selection All Outputs Fully Regulated Remote Sense, Overvoltage Protection and Overtemperature Protection Power Fail Signal Included

More information

Power Supplies 3. SDN-C Compact DIN Rail Series

Power Supplies 3. SDN-C Compact DIN Rail Series SDN-C Compact DIN Rail Series The SDN-C DIN rail power supplies are the next generation of the popular SDN series. These models combine high efficiency and compact size with new visual diagnostic LEDs

More information

Electronic plugs for valves MSE

Electronic plugs for valves MSE Murrelektronik valve plugs with integrated electronic circuits. Saves time, money and space. Electronics With the Murrelektronik electronic valve plugs, we have made it possible to integrate many different

More information

3 Circuit Theory. 3.2 Balanced Gain Stage (BGS) Input to the amplifier is balanced. The shield is isolated

3 Circuit Theory. 3.2 Balanced Gain Stage (BGS) Input to the amplifier is balanced. The shield is isolated Rev. D CE Series Power Amplifier Service Manual 3 Circuit Theory 3.0 Overview This section of the manual explains the general operation of the CE power amplifier. Topics covered include Front End Operation,

More information

CB SERIES MINIATURE, REGULATED HIGH VOLTAGE DC TO DC CONVERTERS

CB SERIES MINIATURE, REGULATED HIGH VOLTAGE DC TO DC CONVERTERS Proven Reliability MINIATURE, REGULATED HIGH VOLTAGE DC TO DC CONVERTERS V to kv at Watt PRODUCT SELECTION TABLE MODEL OUTPUT VOLTAGE OUTPUT CURRENT* RIPPLE CB to +kv to µa

More information

BC145 SIGNAL ISOLATOR BOARD

BC145 SIGNAL ISOLATOR BOARD BC145 SIGNAL ISOLATOR BOARD 4/17 Installation & Operating Manual MN1373 Any trademarks used in this manual are the property of their respective owners. Important: Be sure to check www.baldor.com to download

More information

Brushed DC Motor Control. Module with CAN (MDL-BDC24)

Brushed DC Motor Control. Module with CAN (MDL-BDC24) Stellaris Brushed DC Motor Control Module with CAN (MDL-BDC24) Ordering Information Product No. MDL-BDC24 RDK-BDC24 Description Stellaris Brushed DC Motor Control Module with CAN (MDL-BDC24) for Single-Unit

More information

Accessories Power Amplifiers

Accessories Power Amplifiers Front Panel Vickers Models with Command Logic Module and Ramps EEA-PAM-5**-B- Series General Description Features and Benefits The EEA-PAM-5**-B- Eurocards are power amplifiers with a four-input (demand

More information

Product overview. Features. Product specifications. Order codes. 1kΩ Resistance Output Module

Product overview. Features. Product specifications. Order codes. 1kΩ Resistance Output Module Product overview The AX-ROM135 and the AX-ROM1000 Modules enable an Analogue, Pulse or Floating point signal and convert to either a 0-135Ω or a 1KΩ Proportional Resistive output signal. The output resistance

More information

April 1994 UCM-420A. Setpoint Controller. Operating and Installation Instructions

April 1994 UCM-420A. Setpoint Controller. Operating and Installation Instructions April TM UCM-A Setpoint Controller Operating and Installation Instructions A LARGE number of applications in a SMALL package... REMOTE SETPOINT CONTROLLER LOCAL SETPOINT CONTROLLER - ma SIGNAL GENERATOR

More information

An input resistor suppresses noise and stray pickup developed across the high input impedance of the op amp.

An input resistor suppresses noise and stray pickup developed across the high input impedance of the op amp. When you have completed this exercise, you will be able to operate a voltage follower using dc voltages. You will verify your results with a multimeter. O I The polarity of V O is identical to the polarity

More information

Electronic regulator for PWM controlled proportional solenoid valves FABER -

Electronic regulator for PWM controlled proportional solenoid valves FABER - Electronic regulator for PWM controlled proportional solenoid valves STU Control Unit FABER - COM DESCRIPTION STU-PWM electronic card is a regulator for proportional solenoid valves, which can drive up

More information

Analog Servo Drive 30A20AC

Analog Servo Drive 30A20AC Description Power Range NOTE: This product has been replaced by the AxCent family of servo drives. Please visit our website at www.a-m-c.com or contact us for replacement model information and retrofit

More information

Programmable with Electronic Assistant Simulink

Programmable with Electronic Assistant Simulink TECHNICAL DATASHEET #TDAX022410 2 Universal Inputs, Dual Valve Controller 2 Universal Signal Inputs 2-3A Outputs Drive Hydraulic Valves CAN (SAE J1939) Programmable with Electronic Assistant Simulink P/N:

More information

YVPC ELECTRONIC REGULATOR FOR PWM CONTROLLED SOLENOID

YVPC ELECTRONIC REGULATOR FOR PWM CONTROLLED SOLENOID YVPC ELECTRONIC REGULATOR FOR PWM CONTROLLED SOLENOID Positive - Vdc ±0% Negative Input signal 0 0 Vdc, [.0] [.] 9 [.] DIN 0 [.] 0 [.] 9 [.], [.0], [0.] - I (A) I (A) DZ R t (sec) t (sec) POT RISE RAMP

More information

Anacon Power & Controls Relay Assembly Specialists An Anacon Electronic Sales, Inc. Company

Anacon Power & Controls Relay Assembly Specialists An Anacon Electronic Sales, Inc. Company ZERO CROSS SSR CONTROLLER USERS MANUAL SSR INTELLIGENT POWER CONTROL MODULE TABLE OF CONTENTS Section Page 1 Ordering Code... 3 2 Description... 3 2.1 Features... 3 3 Installation... 3 3.1 Mounting Instructions...

More information

Applications: Off-highway construction equipment Municipal vehicles Material handling equipment (forklifts, etc.) Ordering Part Numbers:

Applications: Off-highway construction equipment Municipal vehicles Material handling equipment (forklifts, etc.) Ordering Part Numbers: TECHNICAL DATASHEET #TDAX021201 CAN to 9 Output Valve Controller P/N: AX021201 CANopen Features: Command messages are received through the CAN network (no physical inputs) 9 outputs are user selectable

More information

CAH CARD. user leaflet. 1 of 15. Copyright Issue 12.1 January 2015

CAH CARD. user leaflet. 1 of 15. Copyright Issue 12.1 January 2015 CAH CARD user leaflet 1 of 15 INTRODUCTION The function of the card is to energise a transducer (LVDT, Half-Bridge or Full-Bridge) with a stable a.c. waveform and to convert the output of the transducer

More information

SilverMax Datasheet. QuickSilver Controls, Inc. NEMA 23 Servomotors.

SilverMax Datasheet. QuickSilver Controls, Inc. NEMA 23 Servomotors. SilverMax Datasheet NEMA 23 Servomotors QuickSilver Controls, Inc. www.quicksilvercontrols.com SilverMax Datasheet - NEMA 23 Servomotors 23 Frame Sizes: 23-3, 23-5, 23H-1, 23H-3, 23H-5 / Series: E, E3,

More information

DSA150 Series. xxx Series. 150 Watts. AC-DC Power Supplies. Models & Ratings. Mechanical Details 3.92 (99.8) 2.18 (55.5) 4.92 (125.

DSA150 Series. xxx Series. 150 Watts.   AC-DC Power Supplies. Models & Ratings. Mechanical Details 3.92 (99.8) 2.18 (55.5) 4.92 (125. 15 Watts xxx Series Ultra Slim Design 15% Peak Load for 3 seconds Ambient Operation from -1 C to +7 C High Efficiency Selectable Overload Characteristic Selectable Remote Inhibit or Enable 3 Year Warranty

More information

TB65 65W Single Output Test and Measurement/Industrial Series

TB65 65W Single Output Test and Measurement/Industrial Series Features 2.0 x 3.5 x 1.3 Package TB65 Up to 65W Convection Cooled Output Power Compliant to high levels of EMC per EN61000-4 15kV ESD (Air), 8kV (Contact) 4kV Surge Meets Class B Conducted EMI with 6db

More information

ABC Series power supplies are ideal for telecom, datacom, industrial equipment and other applications.

ABC Series power supplies are ideal for telecom, datacom, industrial equipment and other applications. The ABC75 Series of open frame power supplies feature a wide universal AC input range of 85 V 264 VAC, offering 75 W of output power in a compact 3 x 2 x 1 inch footprint, with a variety of isolated single

More information

Rev /13 SSRMAN-1B SERIES USERS MANUAL SSR INTELLIGENT BURST FIRING CONTROL COPYRIGHT 2013 NUWAVE TECHNOLOGIES, INC.

Rev /13 SSRMAN-1B SERIES USERS MANUAL SSR INTELLIGENT BURST FIRING CONTROL COPYRIGHT 2013 NUWAVE TECHNOLOGIES, INC. Rev.2.2 12/13 MAN-1B SERIES USERS MANUAL INTELLIGENT BURST FIRING CONTROL COPYRIGHT 2013 MAN-1B Users Manual Page 2 TABLE OF CONTENTS 1. Ordering Codes... 2 2. Description... 2 2.1 Features... 3 3. Installation

More information

These medical power supplies are ideal for monitoring, home health equipment as well as surgical devices.

These medical power supplies are ideal for monitoring, home health equipment as well as surgical devices. The ABC450 Series of open-frame power supplies, with its wide universal 90-264 VAC input range and high power density, is available at 450 W of output power and a variety of single and multiple output

More information

Ordering Part Numbers: SAE J1939 version Controller: AX022400

Ordering Part Numbers: SAE J1939 version Controller: AX022400 TECHNICAL DATASHEET #TDAX022400 2 Universal Inputs, Dual Valve Controller 2 Universal Inputs 2-3A Outputs CAN (SAE J1939) Programmable with Electronic Assistant P/N: AX022400 Features: 2 universal signal

More information

The MBC550 range is ideally suited to a wide variety of medical applications, and also where airflow is limited or not available.

The MBC550 range is ideally suited to a wide variety of medical applications, and also where airflow is limited or not available. The MBC550 Series of open frame medical power supplies feature a wide universal AC input range of 90 264 VAC, offering up to 550 W of output power with forced air cooling, or 250 W with conduction cooling

More information

ABC Series power supplies are ideal for telecom, datacom, industrial equipment and other applications.

ABC Series power supplies are ideal for telecom, datacom, industrial equipment and other applications. The ABC120 Series of open frame power supplies feature a wide universal AC input range of 85 V 264 VAC, offering 120 W of output power in a compact footprint, with a variety of isolated single output voltages.

More information

Switching Regulator. LMT78_1.0R Series Wide input, non-isolated & regulated, single output, SMD package

Switching Regulator. LMT78_1.0R Series Wide input, non-isolated & regulated, single output, SMD package Efficiency up to 95 No need for heat sinks 1.0AMP SMD package Wide input voltage range (4.75V - 36V) Adjustable output voltage Remote ON/OFF control Short circuit protection (SCP), thermal shutdown Very

More information

T6+ Analog I/O Section. Installation booklet for part numbers: 5/4-80A-115 5/4-90A-115 5/4-80A /4-90A-1224

T6+ Analog I/O Section. Installation booklet for part numbers: 5/4-80A-115 5/4-90A-115 5/4-80A /4-90A-1224 T and T+ are trade names of Trol Systems Inc. TSI reserves the right to make changes to the information contained in this manual without notice. publication /4A115MAN- rev:1 2001 TSI All rights reserved

More information

DENISON HYDRAULICS Proportional Pressure Control Valves

DENISON HYDRAULICS Proportional Pressure Control Valves DENISON HYDRAULICS Proportional Pressure Control Valves Series 4VP01 Cetop 03 Publ. 3-EN 2200-B, replaces 3-EN 2200-A FEATURES, SYMBOLS x FEATURES Direct operated pressure relief valve for flow up-to max.

More information

LZS-A500-3 POWER SUPPLY Installation, Operation, and Maintenance Manual. IM-LZSA500-3 January 2008 Revision H

LZS-A500-3 POWER SUPPLY Installation, Operation, and Maintenance Manual. IM-LZSA500-3 January 2008 Revision H LZS-A500-3 POWER SUPPLY Installation, Operation, and Maintenance Manual IM-LZSA500-3 January 2008 Revision H Table of Contents LZS-A500-3 Power Supply 1) Safety and Recommended Practices 2 1.1 General

More information

PRODUCT SPECIFICATION AUDIO LINE AMPLIFIER ALA

PRODUCT SPECIFICATION AUDIO LINE AMPLIFIER ALA PRODUCT SPECIFICATION AUDIO LINE AMPLIFIER ALA0080-2000 FEATURE LIST 2x45Wrms into 6Ω @ 1% THD Entirely differential patented APC (adaptive pole control) amplifier technology 80kHz load independent frequency

More information

TECHNICAL PRODUCT DATASHEET

TECHNICAL PRODUCT DATASHEET FORM-ENG-0018 REV A 06-02-03 ISO 9001 CERTIFIED Phone: (352) 629-5020 or 800-533-3569 Fax: (352)-629-2902 SUITABLE FOR OEM DISTRIBUTION ONLY TECHNICAL PRODUCT DATASHEET High Density PDM 21 Output / 10

More information

Microprocessor Control Board Set Up Procedures (OR PLC)

Microprocessor Control Board Set Up Procedures (OR PLC) Microprocessor Control Board Set Up Procedures (OR-00 PLC) SWITCHES/PUSHBUTTONS Push Buttons at display SW Enter button SW Back button SW Down SW UP Back light on/off switch Rotary switches on main board

More information

FED30-48 S 05 - N HC Series Name Input Output Output Remote Control Assembly Option Voltage Quantity Voltage Option PART NUMBER STRUCTURE

FED30-48 S 05 - N HC Series Name Input Output Output Remote Control Assembly Option Voltage Quantity Voltage Option PART NUMBER STRUCTURE Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger Medical PV Railway PART NUMBER STRUCTURE FED30-48 S 05 - N HC Series Name Input Output Output Remote Control Assembly Option

More information

High Precision 10 V IC Reference AD581*

High Precision 10 V IC Reference AD581* a FEATURES Laser Trimmed to High Accuracy: 10.000 Volts 5 mv (L and U) Trimmed Temperature Coefficient: 5 ppm/ C max, 0 C to +70 C (L) 10 ppm/ C max, 55 C to +125 C (U) Excellent Long-Term Stability: 25

More information

ECC100 Series. -40 ºC to +75 ºC Operation. 100 W - Baseplate Cooled. High Efficiency Resonant Topology. Screw Terminals Available.

ECC100 Series. -40 ºC to +75 ºC Operation. 100 W - Baseplate Cooled. High Efficiency Resonant Topology. Screw Terminals Available. ECC100 Series -40 ºC to +75 ºC Operation 100 W - Baseplate Cooled High Efficiency Resonant Topology Screw Terminals Available 5V Standby Output Remote On/Off & Power OK Signal 3 Year Warranty The ECC100

More information

Industrial PSU with universal input voltage range ( VAC line to line) and configurable output voltage. North America

Industrial PSU with universal input voltage range ( VAC line to line) and configurable output voltage. North America World-Wide 3-phase Input Voltage Range (nom. 200 Vrms to 480 Vrms), PF > 0.94 High Power Density 16 W/in 3 94% Typical Efficiency Parallel Operation up to 16 Units (50.4 kw) Cold-Plate Cooling System -25

More information

DC-DC CONVERTER HFBC60-xxW/O

DC-DC CONVERTER HFBC60-xxW/O DC-DC CONVERTER HFBC60-xxW/O RAILWAY CONVERTER. FOR CHASSIS MOUNTING HIGHLIGHTS + Output Power up to 60 Watts + Ultra Wide Input Range + Wide Temperature Range + Hold-up-time > 10ms + RoHS compliance +

More information

Product Data Sheet. Models 1022/1025/1029C/1032/3629B 3629B. Models 1022/1025/1032. Model 1029C. Model 3629B. Phase Angle Power Control

Product Data Sheet. Models 1022/1025/1029C/1032/3629B 3629B. Models 1022/1025/1032. Model 1029C. Model 3629B. Phase Angle Power Control s 1022/1025/1029C/1032/3629B 3629B Product Data Sheet s 1022/1025/1032 Single phase power controllers Current ratings from 10 to 70 Amps 1022-0 to 5VDC or pot input 1025-4 to 20 ma signal 1032 Current

More information

RangeMAX DIGITAL DIMMING DUAL LAMP CCFL INVERTER MODULE

RangeMAX DIGITAL DIMMING DUAL LAMP CCFL INVERTER MODULE 3 RangeMAX DESCRIPTION The LXMG6 Direct Drive CCFL (Cold Cathode Fluorescent Lamp) Inverter Modules are specifically designed for driving two lamp LCD backlight displays. Similar to the LXMG60, the LXMG6

More information

Electrical Specifications VAC/390 VDC, Universal (Derate from 100% at 115VAC to 78% at 90VAC)

Electrical Specifications VAC/390 VDC, Universal (Derate from 100% at 115VAC to 78% at 90VAC) MWLC550 Medical Features 5 x 3 x 1.5 Inches Form factor Up to 550 Watts with Forced Air Cooled Efficiencies up to 92% -40 to 70 degree operating temperature* 12V / 0.5A Fan Output, Thermal Shut-Down feature

More information

DR3535 DR3535-O. Hardware Reference Manual. Document Revision A7 May 16, 2018 MICROKINETICS CORPORATION

DR3535 DR3535-O. Hardware Reference Manual. Document Revision A7 May 16, 2018 MICROKINETICS CORPORATION -O Hardware Reference Manual Document Revision A7 May 16, 2018 MICROKINETICS CORPORATION 3380 Town Point Drive Suite 330 Kennesaw, GA 30144 Tel: (770) 422-7845 Fax: (770) 422-7854 www.microkinetics.com

More information