OWNER S MANUAL v_01_march_2017

Transcription

1 OWNER S MANUAL v_01_march_2017

2 MARK VISION A WORD FROM MARCO DE VIRGILIIS Thank you for choosing a Markaudio product! Markaudio is a division of Mark World dedicated to pro audio sound reinforcement. Building on the top-level reputation built up over many years by our industry-leading brands Markbass and DV Mark, Markaudio boasts the same high level of innovation and engineering. The result is groundbreaking sound quality, impressive power, and innovative design. Hope you will enjoy your new Markaudio P.A. system, and we invite you to contact us any time with your comments and questions, at info@markaudio.it. Thanks again, and good music! Marco De Virgiliis

3 INDEX 3 INTRODUCTION 4 AS SERIES CONTROL PANEL 6 TECHNICAL DETAILS AS SERIES 802 S 7 TECHNICAL DETAILS AS SERIES 102 S 8 AS SERIES size 9 ACCESSORIES 10 POWER REQUIREMENT / FUSE

4 INTRODUCTION MarkAudio powered subwoofers offer great flexibility, ultra-compact design and exceptional low frequency reproduction. The AS 802 S is an active 2 x 8 subwoofer with 500 watts of power. The AS 102 S is an active 2 x 10 subwoofer with 500 watts of power. AS series combines quality of sound and design with high operating efficiency of power amplifier. They include a powerful MPT (Mark Proprietary Technology) power amp with a precise and focused response on low frequencies and a quick control of distorsion. 3

5 as SERIES CONTROL PANEL MASTER LEVEL (1) This is the MASTER Volume level. CLIP (2) Clip indicator LED. This indicator allows you to visually monitor the volume level of the loudspeaker. LED OFF: compressor/limiter is not engaged. LED ON for a few moments: brief engaging of the compressor/limiter, inaudible to the ears - you are approaching maximum power output, and the speakers are being protected. LED ON: the audio signal is too high, and you should lower the output level of your audio source, or turn the level knob counterclockwise. PHASE (3) Phase inversion In some installations, the subwoofer may be out of phase with the satellites. This switch allows you to reverse the phase of the subwoofer and align the system; ON (4) Power status indicator LED; RIGHT (5) and LEFT (8) INPUT XLR Line XLR input, the XLR 3-pole female jack is electronically balanced (hot pole: #2). You can use unbalanced sources only if your cables have pole 3 jumpered to pole 1. Important: when powering up, turn on your sound source (CD player and mixer, for example) before turning on the Markaudio cabinets. When powering off, turn the cabinets off first; RIGHT (6) and LEFT (9) GROUND LIFT These switches may be needed for the cancellation of hum due to ground loops with other apparatuses; RIGHT (7) and LEFT (10) LINK XLR Line out to connect more subwoofers downstream from the principal system. This 3-pole male XLR jack receives a female XLR plug (7) and sends out a passive signal;

6 COOLING (11) Forced ventilation stabilizes the working temperature of electronic components for continuous performance, even after a long period of operation. Avoid using the loudspeaker on irregular surfaces that might block the vents; AC POWER SOCKET (12) VDE power jack for connecting the power cable from the unit to a wall power source. Make sure the unit is grounded; all three terminals of the AC power plug must be connected to avoid any injury to the user or damage to the unit. Markaudio powered speakers and amps are manufactured to be used in the country where they have been sold, and are factory preset to that country s voltage. So make sure you re sending the correct voltage to your amp before you connect it to AC power. FUSE (13) Fuse housing; ON/OFF SWITCH (14) On/off power switch

7 TECHNICAL DETAILS AS 802 S ACOUSTICAL SPECIFICATIONS Frequency response: 40 Hz- 150 Hz Max SPL: 130 db Woofer: 2 x 8, 4 Ohm INPUT/OUTPUT SECTION Input connectors: stereo XLR female Output connectors: stereo XLR male Input sensitivity: +1.8 dbu (@70 Hz) DSP PROCESSOR SECTION Protections: Thermal, rms Limiter: Soft limiter Controls: Volume, Phas AMPLIFIER Low frequencies Power: 1000 W PEAK (@ 4 Ohm) Low frequencies Power: 500 W RMS (@ 4 Ohm) Cooling: Convection Power Connection: VDE connector CABINET Cabinet Material: multiply poplar Handles: 1 top Pole Mount/Cap: Yes (M20 thread) Colour: Black PHYSICAL Weight: 35.3 lbs / 16 Kg Width: 11 in. /28.1 cm Depth: 20 in. / 52 cm Height: 20 in. / 52 cm 6

8 TECHNICAL DETAILS AS 102 S ACOUSTICAL SPECIFICATIONS Frequency response: 40 Hz- 100 Hz Max SPL: 132 db Woofer: 2 x 10, 4 Ohm INPUT/OUTPUT SECTION Input connectors: stereo XLR female Output connectors: stereo XLR male Input sensitivity: +1.8 dbu (@70 Hz) DSP PROCESSOR SECTION Protections: Thermal, rms Limiter: Soft limiter Controls: Volume, Phase AMPLIFIER Low frequencies Power: 1000 W PEAK (@ 4 Ohm) Low frequencies Power: 500 W RMS (@ 4 Ohm) Cooling: Convection Power Connection: VDE connector CABINET Cabinet Material: multiply poplar Handles: 2 side Pole Mount/Cap: Yes (M20 thread) Colour: Black PHYSICAL Weight: 50.7 lbs / 23 Kg Width: 17 in. / 43 cm Depth: 19 in. / 48 cm Height: 29.3 in. / 74.5 cm 7

9 AS SYSTEMs size mm AS 802 S WEIGHT: Weight: 16 Kg / 35.3 lbs AS 102 S WEIGHT: Weight: 23 Kg / 50.7 lbs 8

10 ACCESSORIES ERGO 802 Cover ERGO 802 and AS 802 cover AC 102 Cover AC 102 and AS 102 S cover 9

11 POWER REQUIREMENT 100V; 120V; 230V; 240V 50/60Hz (Voltage is factory preset according to region of sale). Markaudio amps are manufactured to be sold and used in the country of purchase, and are factory preset to that country s voltage. Due to homologation issues, the voltage may not be changed. FUSE EUROPE 4 A 250V T 5x20 AUSTRALIA/UK 4 A 250V T 5x20 USA/CANADA 8 A 250V T 5x20 JAPAN 10 A 250VT 5x20 10