Casambi CBM-002A/B. Product Specification. Features. Applications. 1 Description

Transcription

1 Casambi CBM-002A/B Product Specification Features Casambi Lighting Control System: Wirelessly controllable with a Bluetooth 4.0 smart device No need for external gateway device Forms automatically a wireless mesh network Device firmware can be updated over-the-air Casambi cloud service available Extremely easy set-up CBM-002A/B Features: Small form factor, 12,7 mm x 20,0 mm x 2,85 mm 12 pcs general purpose input/output pins SPI, TWI, UART, PWM (max. 4 ch) Integrated antenna, two different versions Up to 4 dbm output power and -93 dbm RX sensitivity Range up to 50 m in open air Can be mounted in horizontal or vertical position Delivered pre-loaded with Casambi firmware Applications LED drivers, 1-4 channels Different lighting control applications Light fixtures Single and multicolor LED bulbs 1 Description CBM-002A/B is a Class 2 embedded Bluetooth 4.0 module designed to be integrated into LED drivers, different lighting control applications, light fixtures and LED bulbs. It is pre-programmed with Casambi s proprietary firmware making it completely compatible with other Casambi enable devices. CBM-002A/B is controlled wirelessly with Casambi smartphone and tablet applications using Bluetooth 4.0 protocol. Devices form automatically a self-healing and self-organizing wireless mesh network so that a large number of fixtures can be controlled from any point. No external gateway module is needed. CBM-002A/B contains a powerful 32-bit ARM Cortex -M4 CPU and a 2.4 GHz transceiver with on-board antenna and optional matching circuitry. Different external components, such as motion detectors, ambient light sensors and PWM circuits, can be interfaced with the module by using its 12 general purpose I/O pins. CBM-002A/B can be mounted both in horizontal and vertical position making it very versatile for projects with different form-factors. Page 1 of 25

2 2 Revision history Date Version Description March Original version October Compliance information updated November Compliance information updated January Typo corrected in Table 1 3 Ordering Information Part Number CBM-002A CBM-002B Description CBM-002 with on-board SMD chip antenna CBM-002 with on-board wire antenna Page 2 of 25

3 Table of Contents 1 Description Revision History Ordering Information Operation Block Diagram System Blocks General Purpose I/O (GPIO) Analog-to-Digital Converter (ADC) PWM Output Serial Interfaces Serial Peripheral Interface (SPI) Two-Wire Interface (TWI) Universal Asynchronous Receiver/Transmitter (UART) Pin Assignment Electrical Specifications Absolute Maximum Ratings Power Supply Specifications GPIO Specifications Environmental Conditions Radio Characteristics General Radio Characteristics Communication Interface Characteristics Bit Rates SPI Specifications TWI Specifications PWM Specifications Application Information Smart Switching Power-On Detection Antenna Versions CBM-002B Antenna Mounting Horizontal Mounting Vertical Mounting Mechanical Specifications Page 3 of 25

4 16 Soldering Leaded Reflow Soldering Leadfree Reflow Soldering Hand Soldering Rework Cleaning Compliance Information FCC Statement ISED Statement CE Declaration of Conformity Page 4 of 25

5 4 Operation Casambi CBM-002A/B is an embedded wireless module with a powerful 32-bit ARM Cortex -M4 CPU and a 2.4 GHz transceiver with on-board antenna and optional matching circuitry. It can be integrated, for example, into an LED driver, a light fixture or an LED bulb. CBM-002A/B has total of 12 GPIO pins, which can be configured to perform various tasks, such as SPI, TWI (I 2 C compatible), UART, 4 channel PWM output and 3 channel Analog-to-Digital Converter input. Only the ADC input channels have fixed GPIO pins. Other functions can be freely configured to any GPIO pin. CBM-002A/B is controlled wirelessly by a smart device with Casambi application. Multiple Casambi units form automatically a mesh network, which can be controlled from any point. The network communicates directly with the smart device using Bluetooth 4.0. No external gateway device or Wireless LAN network is needed. CBM-002A/B has an integrated 2,4 GHz antenna. This will have to be taken into account when the device is integrated to any environment. See chapter 14.5 Mounting for further instructions. The module can be operated also from a traditional on/off wall switch. By flicking the switch on and off the user can select different pre-set modes. These modes can affect one or several devices on the network. This way the user does not have to have the smart device at hand all the time in order to select the desired settings or modes. This feature requires an external electrolytic capacitor to supply power during power-off stage as well as a power-on detection circuitry. A large number of different setting of CBM-002A/B can be configured in Casambi Admin webpages and taken into use without a need to re-program the module. These settings include, for example, I/O pin mapping, PWM, push buttons, etc. 5 Block Diagram Crystal, 32 MHz VCC GND GPIO0 GPIO11 SWDCLK SWDIO/nRESET 32 bit Cortex M4 RF-MCU Matching network Picture 1. CBM-002A/B block diagram Page 5 of 25

6 6 System Blocks 6.1 General Purpose I/O (GPIO) CBM-002A/B has 12 General Purpose I/O pins. Each GPIO can be accessed individually and each has the following features: Input/output direction Configurable output drive strength Internal pull-up and pull-down resistors Buffered inputs Trigger interrupt on all pins (rising edge, falling edge, any change) Serial interface and PWM output can be freely configured to each pin GPIO pins 0-3 also supports analog input signals when an internal Analog-to-Digital Converter (ADC) is used. 6.2 Analog-to-Digital Converter (ADC) The up to 12-bit Analog-to-Digital Converter enables sampling of up to 4 external signals (GPIOs 0-3) through a front-end multiplexer. The ADC has configurable input and reference prescaling, and sample resolution (8, 10, and 12-bit). There are two options for the voltage reference: Internal 1,20 V reference VCC with 1/3 prescaling Analog inputs can have a configurable gain of 1/6, 1/5, 1/4, 1/3, 1/2, 1, 2 and 4. The suitable voltage range for ADC input is 0 V - VCC. 6.3 PWM Output Any GPIO pin can be configured to output PWM signal. Up to 4 PWM channels can be used simultaneously. PWM frequency can be determined freely up to 40 khz. PWM frequency is the same with all PWM channels. The maximum resolution is steps and it depends on the PWM frequency. The PWM signal is logic level (max. VCC) and it has driving capacity from 4 ma (standard) up to 14 ma (highdrive). An adjustable analog voltage (0 V - VCC) can be derived from the PWM signal by an external RC filter. A 10 khz PWM signal together with a 10kΩ + 2,2 µf RC filter can be used as a starting point. Depending on the application, it may be necessary to use an operational amplifier as a buffer stage. +3 VDC CBM-002A/B 10 khz PWM 0-3V analog GPIOx G3, V output Picture 2. Adjustable 0-10V output from PWM signal. Page 6 of 25

7 7 Serial Interfaces CBM-002A/B can be connected to an external MCU through its extension interface, which supports SPI, TWI and UART. Through this interface it is possible to, for example, gather information from sensors through Casambi network. 7.1 Serial Peripheral Interface (SPI) CBM-002A/B supports a 3-wire (SCK, MISO, MOSI) bidirectional SPI bus with fast data transfers to and from multiple slaves. CBM-002A/B acts as a master and it provides a simple CPU interface which includes a TXD register for sending data and an RXD register for receiving data. These registers are double-buffered to enable some degree of uninterrupted data flow in and out of the SPI master. Each of the slave devices requires an individual chip select signal which can be connected to any available GPIO pin. The SPI master does not implement support for chip select directly. Therefore, the correct slave must be selected independently of the SPI master. The GPIOs used for each SPI interface line can be chosen from any GPIO on the module and are independently configurable. This enables great flexibility in module pinout and enables efficient use of printed circuit board space and signal routing. The SPI peripheral supports SPI modes 0, 1, 2, and Two-Wire Interface (TWI) The Two-Wire Interface (I 2 C compatible) can interface a bidirectional wired-and bus with two lines (SCL, SDA). The interface is capable of clock stretching and data rates of 100 kbps and 400 kbps are supported. The TWI transmitter and receiver are single buffered. The GPIOs used for each Two-Wire Interface line can be chosen from any GPIO on the module and are independently configurable. This enables great flexibility in module pin-out and enables efficient use of board space and signal routing. 7.3 Universal Asynchronous Receiver/Transmitter (UART) The Universal Asynchronous Receiver/Transmitter offers fast, full-duplex, asynchronous serial communication with built-in flow control support in HW up to 1 Mbps baud. Parity checking and generation for the 9th data bit are supported. The GPIOs used for each UART interface line can be chosen from any GPIO on the module and are independently configurable. This enables great flexibility in module pinout and enables efficient use of board space and signal routing. Page 7 of 25

8 8 Pin Assignment H0 H1 H2 H3 H4 H5 H6 H7 H8 CBM-002A/B Top View H16 H15 H14 H13 H12 H11 H10 H9 H16 H15 H14 H13 H12 H11 H10 H9 CBM-002A/B Bottom View H0 H1 H2 H3 H4 H5 H6 H7 H8 V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 V11 V12 V13 V14 V15 Picture 2. Pin assignment Horizontal Pin Vertical Pin Pin Name Pin Function Description H0 - GND Power Ground H1 H2 H3 H4 V7 V6 V5 V4 GPIO0 AIN0 GPIO1 AIN1 GPIO2 AIN2 GPIO3 AIN3 Digital I/O Analog input Digital I/O Analog input Digital I/O Analog input Digital I/O Analog input General purpose I/O pin ADC input 0 General purpose I/O pin ADC input 1 General purpose I/O pin ADC input 2 General purpose I/O pin ADC input 3 H5 V3 VCC Power Power supply H6 V2 SWDCLK Digital input HW debug and flash programming I/O H7 V1 SWDIO Digital I/O HW debug and flash programming I/O H8 V0 GND Power Ground H9 V8 GPIO4 Digital I/O General purpose I/O pin H10 V9 GPIO5 Digital I/O General purpose I/O pin H11 V10 GPIO6 Digital I/O General purpose I/O pin Page 8 of 25

9 Horizontal Pin Vertical Pin Pin Name Pin Function Description H12 V11 GPIO7 Digital I/O General purpose I/O pin H13 V12 GPIO8 Digital I/O General purpose I/O pin H14 V13 GPIO9 Digital I/O General purpose I/O pin H15 V14 GPIO10 Digital I/O General purpose I/O pin H16 V15 GPIO11 Digital I/O General purpose I/O pin Table 1. Pin assignment 9 Electrical Specifications 9.1 Absolute Maximum Ratings Maximum ratings are the extreme limits to which CBM-002A/B can be exposed without permanently damaging it. Exposure to absolute maximum ratings for prolonged periods of time may affect the reliability. Absolute Maximum Ratings Min. Max. Units Supply voltage, VCC -0,3 +3,9 V GND 0 V I/O pin voltage, VIO -0,3 VCC + 0,3 V Storage temperature C Operating temperature, TA C Table 2. Absolute maximum ratings 9.2 Power Supply Specifications Power Supply Specifications Min. Typ. Max. Units Supply voltage, VCC +2,5 +3,0 +3,6 V Supply current, ICC 7 ma Table 3. Power supply specifications Page 9 of 25

10 9.3 General Purpose I/O Specifications GPIO Specifications Input high voltage, VIH Min. 0,7xVCC Input low voltage, VIL GND 0,3xVCC V Output high voltage, VOH VCC-0,4 VCC V Output low voltage, VOL GND 0,4 V Source current, IGPIO_OUT ) ma Sink current, IGPIO_IN ) ma Pull-up resistance, RPU kω Pull-down resistance, RPD kω Table 4. GPIO specifications 1) If required source/sink current in any GPIO pin is more than 4 ma, corresponding GPIO pin must be configured as high-drive. Typ. Max. VCC Units V 10 Environmental Conditions Environmental Conditions Min. Typ. Max. Units Storage temperature C Operating temperature, TA C Relative humidity, storage 90 % Relative humidity, operating 80 % Table 5. Environmental conditions 11 Radio Characteristics 11.1 General Radio Characteristics General Radio Characteristics Operating frequencies, fop, 1 MHz chann. spacing Min. Typ. Units MHz PLL programming resolution, PLLres 1 MHz Frequency deviation, fble ±225 ±250 ±275 khz On-air data rate, bpsfsk kbps Maximum output power, PRF +4 dbm Sensitivity, PSENS dbm Table 6. General radio characteristics Max. Page 10 of 25

11 12 Communication Interface Characteristics 12.1 Bit Rates Bit Rates Min. Typ. Max. Units Bit rate for SPI, fspi 0,125 8 Mbps Bit rates for TWI, f2w kbps Baud rate for UART, fuart 1, kbps Table 9. UART specifications 12.2 SPI Timing Parameters SCK tch tcl MISO tdc tdh b7 b6 b0 MOSI b7 tcd b0 Picture 3. SPI timing diagram, one byte transmission, SPI mode 0 SPI Timing Parameters Data to SCK setup, tdc Min. Typ. Units 10 ns SCK to Data hold, tdh 10 ns SCK to Data valid, tcd ns SCK High time, tch 40 ns SCK Low time, tcl 40 ns SCK Frequency, fsck 0,125 8 MHz SCK Rise and Fall time, tr, tf Table 11. SPI timing parameters Max. 100 ns Page 11 of 25

12 12.3 TWI Timing Parameters SCL 1/fSCL thd_sda tsu_dat thd_dat tsu_sto tbuf SDA Picture 4. TWI SCL/SDA timing TWI Timing Parameters SCL clock frequency, fscl Hold time for START and repeated START condition, thd_sta Data setup time before positive edge on SCL, tsu_dat Data hold time after negative edge on SCL, thd_dat Setup time from SCL goes high to STOP condition, tsu_sto Bus free time between STOP and START conditions, tbuf Standard Fast Min. Max. Min. Max. Units khz ns ns ns ns ns Table 13. TWI timing parameters 13 PWM Specifications PWM Specifications PWM frequency, fpwm PWM high output voltage, VPWM_H VCC-0,4 VCC V PWM low output voltage, VPWM_L GND 0,4 V PWM sink/source current, IPWM ) ma PWM resolution steps PWM fpwm 10 khz PWM fpwm 20 khz PWM fpwm 40 khz Table 16. PWM specifications Min. Typ. Max Units khz steps steps steps 1) If required source/sink current in any GPIO pin is more than 4 ma, corresponding GPIO pin must be configured as high-drive. 400 Page 12 of 25

13 14 Application Information 14.1 Smart Switching Casambi has developed a solution for controlling lighting with only a traditional on/off wall switch. By default, the wall switch can be used to dim the lights, but different settings can be selected from Casambi App, such as selecting a pre-set mode. With Smart Switching feature, multiple lights can be controlled from a single switch. Smart Switching feature is used by flicking the wall switch quickly off and on. Smart Switching is a function which requires an external electrolytic bypass capacitor and a power-on detection circuitry to work. The external electrolytic capacitor is needed to supply the necessary operating voltage for the module during power-off stage. It can be either an external capacitor just for the CBM-002A/B, or it can be a part of a larger power supply on the host board. If the capacitor is dedicated just for the CBM- 002A/B, the minimum required capacitance is 1200 µf. It is advisable to connect the capacitor before any voltage regulation for larger voltage drop. Even if Smart Switching feature is not used, the correct use of CBM-002A/B still requires the power-on detection and the external capacitor. These are needed so that the module can inform Casambi network when its power is cut off. The external capacitor will provide power to the module a short time after the power has been switched off. A suitable time for Smart Switching is 1,5 seconds and without Smart Switching 0,5 seconds. The external capacitor will have to be sized according to these requirements. It is a good practice to use a capacitor with temperature range up to 105 C. Bypass capacitor for Smart Switching Basic linear regulator circuit CinC Linear regulator, Vout 3,0 V out Vcc CBM-002A/B GPIOs Picture 7. Powering CBM-002A/B with an external capacitor for Smart Switching Page 13 of 25

14 14.2 Power-On Detection In order to operate correctly, the Casambi network will have to know if the power has been switched off from some unit. For this reason, the unit will have to know when its power has been switched off. This is done by a power-on detection together with an external capacitor (see previous chapter). In case of CBM-002A/B the power-on detection is a signal that is connected to any GPIO pin. The signal can be one of the following four types: - constant high signal when power is present, low signal when power is absent - constant low signal when power is present, high signal when power is absent - 50/60/100/120 Hz square wave signal when power is present, constant low signal when power is absent - 50/60/100/120 Hz square wave signal when power is present, constant high signal when power is absent The power-on signal can be derived from either DC voltage or AC mains voltage. If the host application is mains powered, so called Zero Detect circuitry shall be designed. The Zero Detect circuitry is connected to mains voltage and it detects when the voltage crosses the zero point. This information is needed to determine when the wall switch has been switched off and when it is switched back on. In mains voltage powered application, CBM-002A/B requires one or two Zero Detect pulses on each mains cycle, so the mains voltage can be half- or full-wave rectified. Also the use of a schmitt trigger is strongly advised in order to get clean pulses. No application schematics of the Zero Detect circuitry is provided on this datasheet. This is because the application and the surrounding electronics may vary greatly which makes it impossible to provide a solution that works on every application. The designer of the host system will have to design a suitable Zero Detect circuitry. If the host system power supply is isolated, the Zero Detect signal will have to be isolated as well. Extreme caution will have to be used when working with Zero Detect since potentially lethal mains voltages are involved. The voltage level of the Zero Detect signal will have to be suitable for CBM-002A/B. Zero Detect signal can be connected to any free GPIO pin on CBM-002A/B. Use of the external capacitor and Zero Detect circuitry is strongly advised. In addition to Smart Wall Switch feature they enable faster response to the power-off condition. When the mains voltage is cut out from the device with CBM-002A/B, the capacitor supplies enough power for the module to send status update to the network. This way the status of the module is immediately updated to offline on the Casambi application. If the external capacitor and Zero Detect circuitry is omitted, the module will have to send status information to the network periodically which causes a delay to the status update on the application as well as unnecessary traffic on the network. Page 14 of 25

15 14.3 Antenna Versions CBM-002A/B is available in two different antenna versions. CBM-002A is equipped with an on-board SMD chip antenna and CBM-002B is equipped with a 1/4 wavelength dipole antenna. Usually CBM-002B offers better range, but CBM-002A is more compact solution. CBM-002B is delivered with the antenna detached, so the antenna will have to be soldered in place before taking the module into use. This is because the antenna can be soldered in vertical or horizontal position. The host device application determines which antenna orientation is more suitable. Read 14.5 CBM-002B Antenna for more information. Picture 7. CBM-002A on left and CBM-002B on right Page 15 of 25

16 CBM-002B Antenna CBM-002B is delivered with the antenna detached. The antenna is a 27 mm long single strand copper wire and it can be soldered in horizontal or vertical orientation, depending on the best suitability for the host application. The antenna can be bent to fit the host application better. However, there are some guidelines that need to be taken into consideration. 1. Make sure that antenna is not in contact with any kind of metal. 2. The antenna should be places as far away from any metal structures as possible. 3. The tip of the antenna is especially sensitive for close by metals. 4. The less bending is done on the antenna, the smaller impact it haves on the range. 4. Do not use any other kind of antenna, or do not cut or otherwise modify the delivered antenna. The antenna is soldered onto the left side solder pad (the pad closer to the antenna matching components). When soldering the antenna in horizontal position, for correct operation, place the antenna so that it fills the whole length of the soldering pad. This way the antenna extents over the edge of the module by 23,5-24,0 mm. When the antenna is soldered in vertical position, solder it so that the antenna rises 23,5-24,0 mm over the PCB surface. Cut the antenna wire from the bottom side to the desired length. This cutting does not affect the performance or approvals. Important! CBM-002B has been certified with the supplied antenna and modifying it beyond the instructions given in this datasheet will void the certification. Picture 9. Soldered CBM-002B antennas Mounting CBM-002A/B has two sets of soldering pads, which allow it to be mounted both in horizontal and vertical position. In some application, such as LED drivers, there are large components which could affect the antenna performance greatly if the module is mounted at the bottom of the device horizontally on the main PCB. Also, horizontally mounted module has much larger footprint compared to vertically mounted module. Page 16 of 25

17 For such cases the module can be mounted in vertical position, either by soldering it to a 1,27 mm pitch 2-row pin header, or by soldering the module directly into a routed slot on the main PCB. When mounted in horizontal position there will have to be two keep-out areas; one for the antenna area and one for the unused pads used for vertical assembly Horizontal Mounting When CBM-002A/B is mounted in a horizontal position it is soldered in by using the soldering pads on both long sides of the module. The soldering pads are designed so that the module can be both hand and reflow soldered. When mounted in a horizontal position, there are two mandatory keep-out areas involved. One is for antenna and the other is for bottom side soldering pads at the narrow end of the module. These pads are used for vertical assembly. For the CBM-002A, the antenna keep-out applies to all layers of the mother board. There shall not be any components, traces, pads or copper areas in any layer within the keep-out area. The same applies to other metals as well, such as the enclosure of the product, fixing screws, etc. The keep-out area for the soldering pads applies only to the outer surface of the mother board. 1) 10,00 3,20 4,75 4,75 2,00 1,00 6,00 2,00 3) 2) 2 x Ø3,00 20,00 1,00 CBM ,00 1,00 CBM-002B 1,50 1,50 3,00 2) 0,20 2,40 3,00 2) 0,20 2,40 11,00 13,70 11,00 13,70 Picture 9. Recommended land pattern for horizontal assembly and required keep-out areas 1) This keep-out area will have to be kept clear from any parts, traces and copper on all layers. 2) This keep-out area applies only to the layer closest to the module. 3) If CBM-002B antenna is soldered vertically, this keep-out area will have to be a hole. Otherwise keep-out area applies only to the layer closest to the module. Page 17 of 25

18 Vertical Mounting CBM-002A/B can be mounted in vertical position by using the soldering pads on the narrow end of the module. There are two methods of soldering the module in vertical position. It can be either soldered between pin rows of a 2-row 1,27 mm pin header (2 x 8P) or it can be soldered in a 0,9 mm slot routed on the main board with soldering pads at the edge of the slot. The thickness of the module printed circuit board is 0,85 mm. Pad size: 1 x 2 mm 0,90 Routed slot 1,27 12,7 Picture 11. Suggested land pattern for vertical mounting in a slot 15 Mechanical Specifications 2,85 12,70 2,35 23,5-24,0 12,70 1,50 1,50 CBM-002A 1,00 20,00 1,50 CBM-002B 1,00 20,00 1,50 2,00 3,00 2,00 2,00 3,00 2,00 0,85 1,905 1,27 1,00 1,905 1,27 1,00 0,85 1,905 1,27 1,00 1,905 1,27 1,00 Picture 14. Mechanical dimensions Page 18 of 25

19 16 Soldering 16.1 Leaded Reflow Soldering Temp. ( C) Max. 235 C 10s (±1s) 220 C (±5 C) 200 C 150 C (±10 C) 30s (+20s/-10s) 90s (±30s) Time (s) Picture 12. Recommended temperature profile for leaded reflow soldering 16.2 Leadfree Reflow Soldering Temp. ( C) Max. 230 C C 220 C 150 C 190 C 30s (+20s/-10s) 90s (±30s) Time (s) Picture 13. Recommended temperature profile for leadfree reflow soldering Maximum number of reflow cycles: 2 Opposite side reflow is prohibited due to the module s weight. (i.e. you must not place the module on the bottom / underside of your PCB and reflow). Page 19 of 25

20 16.3 Hand Soldering Hand soldering is possible. When using a soldering iron, follow IPC recommendations (reference document IPC-7711) Rework The module can be unsoldered from the host board. Use of a hot air rework tool should be programmable and the solder joint and module should not exceed the maximum peak reflow temperature of 250 C. If temperature ramps exceed the reflow temperature profile, module and component damage may occur due to thermal shock. Avoid overheating. Never attempt a rework on the module itself, (e.g. replacing individual components) Cleaning In general, cleaning the populated modules is strongly discouraged. Residuals under the module cannot be easily removed with any cleaning process. Use of No Clean soldering paste is strongly recommended, as it does not require cleaning after the soldering process. 17 Compliance Information Compliance Information Radio USA FCC Part 15 Subpart C FCC ID (CBM-002A): 2ALA3-CBM002A FCC ID (CBM-002B): 2ALA3-CBM002B Canada IC (CBM-002A): RSS CBM002A IC (CBM-002B): CBM002B Europe ETSI EN v2.1.1 Environmental RoHS RoHS compilant REACH REACH compilant Table 18. Compliance information Page 20 of 25

21 17.1 Federal Communications Commission (FCC) Statement Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning Changes or modifications not expressly approved by could void the user s authority to operate the equipment. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. It is the host manufacturer s responsibility to ensure continued compliance with FCC requirements once the module has been installed in to the host product. Page 21 of 25

22 17.2 Innovation, Scientific and Economic Development Canada (ISED) Statement Radiation Exposure Statement for Canada This device complies with Industry Canada s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment is exempt from the routine RF exposure evaluation requirements of RSS-102. This equipment should be installed and operated with a minimum distance of 20 cm between the antenna and the user or bystanders. Le présent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence. L exploitation est autorisée aux deux conditions suivantes: (1) l appareil ne doit pas produire de brouillage; (2) l utilisateur de l appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d en compromettre le fonctionnement. Ce matériel n est pas sujet à l évaluation habituelle d exposition RF selon RSS102. Ce matériel devrait être installé et exploité en gardant une distance minimale de 20 cm entre l antenne et l utilisateur ou les spectateurs. Antenna Warning CBM-002B radio transmitter has been approved by ISED to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. L émetteur radio CBM-002B est approuvé par les indicateurs du développement énergétique durable pour fonctionner avec les types d antennes énumérés ci-dessous avec la valeur maximale de gain autorisée indiquée. L utilisation des types d antennes exclus de cette liste, ayant un gain plus élevé que la valeur maximale de gain indiquée pour le type en question, est strictement interdite avec cet appareil. Approved antenna: 27 mm long solid copper wire with conductor diameter of 0,6 mm soldered in place according to the instruction given in this document (see chapter CBM-002B Antenna). Maximum permissible antenna gain is 2,0 dbi. Le fil de cuivre 27 mm de long avec un diamètre conducteur de 0,6 mm soudé en place conformément aux instructions contenues dans ce document (voir chapitre Antenne CBM- 002B). Valeur maximale permise pour gain d antenne est de 2,0 dbi. Under ISED regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by ISED. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Sous les règlements des indicateurs du développement énergétique durable, cet émetteur radio peut seulement fonctionner en utilisant un type d antenne avec une valeur maximale (ou moindre) de gain approuvée pour l émetteur par les indicateurs du développement énergétique durable. Afin de réduire la possible interférence radio avec les autres utilisateurs, le type d antenne et son gain doivent être sélectionnés afin que la puissance isotrope rayonnée équivalente ne soit pas supérieure à ce qui est nécessaire pour une communication réussie. Page 22 of 25

23 End Product Labeling CBM-002 has been labeled with its own FCC ID and IC Certification Number. The end product manufacturer must ensure that FCC and ISED labeling requirements are met. If the FCC ID and IC Certification Number of CBM-002 are not visible when the module is installed inside another device, then the device must have a clearly visible label containing the following information: CBM-002 a été identifié avec son propre numéro d identification de la FCC ainsi que son numéro de certification IC. Le fabricant du produit final doit assurer que les obligations d identification de la FCC et des indicateurs du développement énergétique durable soient satisfaites. Si le numéro d identification de la FCC et le numéro de certification IC pour CBM-002 ne sont pas visibles lors de l installation du module dans un autre appareil, une étiquette claire et visible avec les informations ci-après devra alors être apposée sur l appareil: CBM-002A: Contains FCC ID: 2ALA3-CBM002A Contains IC: CBM002A CBM-002B: Contains FCC ID: 2ALA3-CBM002B Contains IC: CBM002B It is the host manufacturer s responsibility to ensure continued compliance with ISED Canada requirements once the module has been installed in to the host product. Il incombe au fabricant de l hôte d assurer la conformité continue aux exigences d ISED Canada une fois que le module a été installé sur le produit hôte. Page 23 of 25

24 End Product User Manual User manual for end product with CBM-002A or CBM-002B module inside shall contain the following or equivalent notice in a conspicuous location in the user manual or alternatively on the device or both: Le mode d emploi pour le produit fini avec le module CBM-002A ou CBM-002B installé devra contenir les informations ci-après ou un avis équivalent dans un endroit bien en vue du mode d emploi ou, alternativement, sur l appareil, ou aux deux endroits: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation This device complies with Industry Canada s licenseexempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence. L exploitation est autorisée aux deux conditions suivantes: (1) l appareil ne doit pas produire de brouillage; (2) l utilisateur de l appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d en compromettre le fonctionnement. Page 24 of 25

25 17.3 CE Declaration of Conformity Hereby, declares that the radio equipment types CBM-002A and CBM-002B are in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: CE Regulatory Information When integrating a radio module into an end product the integrator becomes the manufacturer of the final product and is therefore responsible for demonstrating compliance of the final product with the essential requirements of the Radio Equipment Directive (RED). Some additional certification processes are required before placing the product on the market in EU member states to make the end product fully comply with relative EU standards., Data is subject to change without prior notice. Page 25 of 25