Absolute encoder GEL 15X F. Serial (SSI) or parallel interface, PC-programmable. Technical information version 01.06

Size: px
Start display at page:

Download "Absolute encoder GEL 15X F. Serial (SSI) or parallel interface, PC-programmable. Technical information version 01.06"

Transcription

1 Absolute encoder 5xF Serial (SSI) or parallel interface, PC-programmable Technical information version 0.06 converter module KM V DC + 0% 5X F connecting cable VK 50.2 (SSI) VK 50.3 (parallel) COM/2 cross-over serial PC cable VK 50. Internet http// Tel. +49 (0) Lenord, Bauer & Co. GmbH info@lenord.de Fax +49 (0) Dohlenstrasse Oberhausen, Germany

2 General information Function The 5XF series has been developed with the intention of enabling the user to change plant-specific parameters. The encoder can be programmed by means of a PC via the encoder programming line. The selected parameters stored in an E 2 PROM in the absolute encoder are protected against power failures. The programming software BB 50 (3 /2" diskette,.4 MB) for menu-guided programming runs on any IBM-compatible PC-AT with a main memory of 52 KB and DOS 3. or higher. The RS 485 interface signals are converted to the PCcompatible RS 232 interface in the converter cable. Programmable parameters Resolution to steps/360 Measuring range,2,4... 4,096 revolutions Output code Gray, Gray-Tanne, BCD, Binary or Binary-Tanne Code direction CW or CCW Logic polarity positive or negative (only with parallel interface) Parity bit ODD or EVEN Setmodes Set Reference or Up-Down mode Reference value 0 to total number of steps Reference value 2 0 to total number of steps Offset value - 32, ,768 Length of register 3, 6, 25 or 32 Bit (only with SSI interface) Monostable time µs (only with SSI interface) Identification number ,535 (ID number) Setmodes The functions Set Reference or Up-Down Mode can be programmed via inputs FE and FE2. FE FE0 Setmode Set Reference 0 0 normal coding mode 0 set reference point 0 set reference point 2 output value stored (latch) The Set Reference mode permits setting of reference points or 2. The reference values can be programmed by the user within the total number of steps. In the Up-Down Mode, the output value of the absolute encoder can be increased or reduced by the user via the function inputs. The output change speed increases with the duration of signal application. Applying a logic 0 for a short time reset the output change speed. The set value is stored after about 6 seconds before the absolute encoder switches over to the normal coding mode. These functions can be used for electronic setting such as for changing the zero setpoint. Timing diagrams t V t H t W t R t LA t D t EN Set reference point FE FE0 data bits latch FE FE0 data bits enable (only with parallel interface) data bits t D tw stable preset value t R t V t H t LA t EN latch inaktice delay =. ms max. hold = 750 µs min. wait = 70 ms min. response = 60 ms latch response = 750 µs max. time difference of monostable circuits = 00 µs max. response = 00 µs max. t D t V t EN FE FE0 Setmode Up-Down mode 0 0 normal coding mode 0 reduce output value and set (down) 0 increase output value and set (up) output value stored (latch) 2 Lenord +Bauer DS22-5XF(0.06)

3 Technical data Electrical data Sensor system GaAlAs-diode-photo-array, photo-transistors M easuring step deviation < + 2' 38" Parallel outputs open collector, open emitter Serial outputs (SSI) RS 422 / 485 P arallel output frequency max. 30 khz at0 bits/360 Output Signal code input E6 (code direction) Gray, Gray-Tanne, Binary, Binary-Tanne, BCD CW or CCW S ignal input E6 (latch) via function inputs (FE) Signal Operating input E6 (enable) range circuit active or inactive + V V DC Operating speed O perating current 80 ma typical, 20 ma max. Electromagnetic compatibility (EMC) electromagnetic emissions according to EN electromagnetic immunity according to EN Mechanical characteristics 3,000 min - max. (permanent ) 4,000 min - max. (short-time ) Values for maximum shaft load and operating tempera- tures -20 C C. Higher values possible under less stringent conditions. Angular acceleration rad/ s max. Moment of inertia (rotor) 2 50 gcm O perating torque < Ncm at a speed of,000 min S tarting torque < Ncm - 5 Admissible load on shaft 250 N axial and radial Bearing life 0 9 revolutions Weight approx. 0.7 kg Ambient conditions O perating temperature range -20 C C (optional -40 C C) Storage Admissible temperature range relative humidity -25 C C 85 % without condensation S chock resistance 200 m/s²; ms (DIN IEC 68) V ibration resistance 5 Hz...,000 Hz; 00 m/s² (DIN IEC 68) Protection class (DIN 40050) 52/58 54 IP 65 (Nilos ring) IP 66 (radial packing ring) DS22-5XF(0.06) Lenord +Bauer 3

4 Input/Output circuits Synchronous Serial Interface (SSI) Input E6 Function input active high I e + input log 0 log V + V V U e - input valid for signal latch set enable code direction (counting direction) D265A Output circuit for G, B, R Output circuit 0 open collector darlington (pull-down) Output circuit 2 open emitter darlington (pull-up) Output circuit 3 SSI (to RS 422/RS 485) + U B + U S GaAlAs diodes P/S t m phototransistors optocoupler + U B 0 V output I a output current source I a (pulldown U a U a current) trigger parallel-serial converter U I driver clock + clock - data + data - code direction I A < 50 ma I A < 20 ma D625A Synchronous Serial Interface (SSI) Advantages lower costs and and reduced work due to minimized wiring increased data safety due to repeat transmissions maximum noise immunity due to symmetrical and snchronous data signals The parallel data word generated by the encoder is converted into a serial data word and transmitted synchronously with the clock signal to the receiver electronics. Example wait cycle rest cycle clock in + rest cycle data out rest cycle M2 M M0 M9 M8 M7 M6 M5 M4 M3 M2 M S2 S S0 S9 S8 S7 S6 S5 S4 S3 S2 S 0 MSB LSB corresponds to the classical SSI protocol for 24 significant data bits programmable multi-turn absolute encoder with a full data word consisting of 24 bits programmed to 4096 steps/revolution in Gray and binary code 4 Lenord +Bauer Proto2 DS22-5XF(0.06)

5 Pin layout Parallel interface Pin layout for 37-pole sub-miniature connector (IP 30) DB 37S depth of connector approx Solder side through 24 Bit Bit PR- 26 PR+ 27 rror-bit 28 Parity-Bit 29 not connected 30 unction input 3 unction input 0 32 nable 33 Code direction 34 V 35 Signal 36 Supply 37 Supply LSB depending on programming MSB depending used are logic 0 on programming; bits not interface for PC programming via E on error set to "0" programmable F input circuit E6 F input circuit E6 E input circuit E6 input circuit E6, also programmable 0 reference potential V DC (+ U ) only for 5xG4096A25 S V DC (+ U ) B 0 V DC (-U ) jumpered to pole 34 B Serial interface (SSI) Pin layout for 2-pole round connector (IP 65) GG approx. 60 Solder side K A B J L C H M D G F E A C lock in - differential clock input (optocoupler ) B Clock in + for driver as per RS 422/485 standard C Data out+ differential data output with D Data out - specifiction as per RS 422/485 standard E F PR- PR+ interface for PC programming via converter cable KV 50; differential transceiver as per RS 485 standard G not connected H Code direction input circuit E6, also programmable J Function input input circuit E6 K Function input 0 input circuit E6 L Supply U B = V DC M Supply - U = 0 V DC B Ø 2.5 GW (Please order separately) Ø approx. 3.5 DS22-5XF(0.06) Lenord +Bauer 5

6 f8 f6 approx.48.5 f7 f7 Dimensioned drawings 52F xF x 20 Æ 65 Æ 60 Æ 45 f7 Æ 2 h7 approx M5 x 9 74 length 30 cm with 37-pole sub-miniature D-connector 55 54F 5xF30 ± x 20 Æ 64 Æ 59 Æ 36 Æ 0 Æ 65 M4 x 9 72 length 30 cm with 37-pole sub-miniature D-connector Æ 6 Æ 65 Æ 58 Æ 50 approx pole round connector GG (standard) B-035 E2652B approx pole round connector GW cable outlet adjustable in 90 steps B-0304 E2652C 58F 7 length 30 cm with 37-pole sub-miniature D-connector 42 M4 x 5 (3 x 20 ) B Lenord +Bauer DS22-5XF(0.06)

7 Available types, Accessories Available types Accessories Type Output circuit Included in scope of supply VK 50. cross-over serial connecting cable (2 m) VK 50.2 connecting cable (SSI) 0.5 m VK 50.3 connecting cable (parallel) 0.5 m 52 F00 54 F00 58 F00 52 F20 54 F20 58 F20 52 F30 54 F30 58 F30 0 (pull-down) 2 (pull-up) 3 (SSI) 37-pole sub-miniature D-mating connector 2-pole round connector, straight type GG alternatively round connector, right-angle GW (optional) KM 50.0 KM 50. KM 50.2 BB 50 converter module incl. cross-over serial cable VK 50. (2 m) converter module (SSI) with connecting cable VK 50.2 (0.5 m) incl. cross-over serial cable VK 50. (2 m) converter module (parallel) with connecting cable VK 50.3 (0.5 m) incl. cross-over serial cable VK 50. (2 m) software for programming of absolute encoder parameters Spare parts GG GW DB 37S 2-pole round connector, straight (SSI) 2-pole round connector, right-angle (SSI) 37-pole sub miniature D-connector, female Technical changes and errors reserved. DS22-5XF(0.06) Lenord +Bauer 7

8 Reply-Fax Customer-specific programming Fax +49 (0)2 08 / Sender Name... Contact/person in charge Street Postal code/city Phone... Phone... Fax... Fax... Parameter Resolution Measuring range Output code Range of values , ) steps /360, 2, revolutions Gray-, Binary or BCD Gray-Tanne, Binary-Tanne Parallel Basic programming,096 interface Basic programming 4 4,096 4,096 4,096 Gray Gray SSI interface Preprogramming Preprogramming Code direction CW / CCW CW CW Logic polarity positive or negative positive Parity bit ODD or EVEN EVEN EVEN Set modes preset or Up-Down mode preset preset Reference Reference value value total no. of steps total no. of steps 0 0 Offset value -32, , Length Monostable of register time 3, 6, 25 or 32 bits µ s 20 Identification no , ) with Gray-Tanne or Binary-Tanne only Unless otherwise specified in the Pre-Programming column, the absolute encoders are supplied with the indicated Basic Programming. 8 Lenord +Bauer DS22-5XF(0.06)

Technical data. General specifications. Linearity error ± 0.1 Electrical specifications Operating voltage U B

Technical data. General specifications. Linearity error ± 0.1 Electrical specifications Operating voltage U B Model Number SYNCHRON SERIELLES INTERFACE Features Very small housing Up to 32 Bit multiturn SSI interface Free of wear magnetic sampling High resolution and accuracy Description The ENA36IL series are

More information

Technical data. General specifications V DC Power consumption P 0. 1 W Time delay before availability t v

Technical data. General specifications V DC Power consumption P 0. 1 W Time delay before availability t v Model Number SYNCHRON SERIELLES INTERFACE Features Very small housing Up to 32 Bit multiturn SSI interface Free of wear magnetic sampling High resolution and accuracy Description The ENA36IL series are

More information

LENORD. +BAUER... automates motion. GEL 2037 with heavy duty flange or tooth wheel adapter. Technical information Version General.

LENORD. +BAUER... automates motion. GEL 2037 with heavy duty flange or tooth wheel adapter. Technical information Version General. GEL 2037 with heavy duty flange or tooth wheel adapter LENORD +BAUER... automates motion. Technical information Version 2014-07 General Multiturn absolute rotary encoders with a resolution of up to 25

More information

Encoder - Absolut 2RMHF-SSI

Encoder - Absolut 2RMHF-SSI Absolute Encoder: Ø24 mm Hollow Shaft: Ø3 mm to ¼ Inch Singleturn or Multiturn SSI Interface Binary or Gray Code Preset of Zero Position Choice of Counting Direction IP-Rating: IP64 or IP67 Mechanical

More information

LENORD. +BAUER... automates motion. Magnetic absolute rotary encoder GEL 2037 with heavy duty flange or tooth wheel adapter

LENORD. +BAUER... automates motion. Magnetic absolute rotary encoder GEL 2037 with heavy duty flange or tooth wheel adapter Magnetic absolute rotary encoder GEL 2037 with heavy duty flange or tooth wheel adapter LENORD +BAUER... automates motion. Technical information Version 01.12 General Multiturn absolute rotary encoders

More information

Magnetic absolute rotary encoder GEL 235 Singleturn, Multiturn up to 28 bits (SSI)

Magnetic absolute rotary encoder GEL 235 Singleturn, Multiturn up to 28 bits (SSI) Magnetic absolute rotary encoder GEL 25 Singleturn, Multiturn up to 28 bits (SSI) Technical information version 09.06 Unique Nonius-evaluation Measuring principle: magnetic, high resolution Evaluation:

More information

Technical data. General specifications. Linearity error ± 0.1 Functional safety related parameters MTTF d 700 a at 40 C Mission Time (T M ) L 10

Technical data. General specifications. Linearity error ± 0.1 Functional safety related parameters MTTF d 700 a at 40 C Mission Time (T M ) L 10 Model Number SYNCHRON SERIELLES INTERFACE Features Recessed hollow shaft SSI interface Up to Bit multiturn Free of wear magnetic sampling High resolution and accuracy Additionally push buttons for preset

More information

Technical data. General specifications. Linearity error ± 0.1 Functional safety related parameters MTTF d 700 a at 40 C Mission Time (T M ) L 10

Technical data. General specifications. Linearity error ± 0.1 Functional safety related parameters MTTF d 700 a at 40 C Mission Time (T M ) L 10 Model Number SYNCHRON SERIELLES INTERFACE Features Solid shaft SSI interface Up to Bit multiturn Free of wear magnetic sampling High resolution and accuracy Additionally push buttons for preset function

More information

Technical data. General specifications V DC No-load supply current I 0. typ. 50 ma Power consumption P 0

Technical data. General specifications V DC No-load supply current I 0. typ. 50 ma Power consumption P 0 Model Number SYNCHRON SERIELLES INTERFACE Cable pull rotary encoder with SSI interface Features Solid yet lightweight plastic construction Compact, slim design (the shaft of the mounted rotary encoder

More information

Scroll down to view your document!

Scroll down to view your document! Over 00 years cumulative experience 24 hour rush turnaround / technical support service Established in 993 The leading independent repairer of servo motors and drives in North America. Visit us on the

More information

Magnetic absolute encoder GEL 2035 Serial interface (SSI), 24 Bit

Magnetic absolute encoder GEL 2035 Serial interface (SSI), 24 Bit Magnetic absolute encoder GEL 2035 Serial interface (SSI), 24 Bit Technical information Version 03.09 Resolution: Precision: 0.8 Signal pattern: Singleturn (ST): Multiturn (MT): up to 24 Bit SSI and SSI

More information

Material: Weight: Shaft Loads:

Material: Weight: Shaft Loads: Absolute Encoder Type SCA36NA-SSI Absolute Encoder - Ø 36 mm Shaft - Ø 6 mm Singleturn or Multiturn SSI Interface Binary or Gray Code Preset of Zero Position Choice of Counting Direction Enclosure Rating

More information

Multiturn absolute encoder

Multiturn absolute encoder 0102 Model Number SYNCHRON SERIELLES INTERFACE Features Up to 30 Bit multiturn ATEX approval IECEx approval Flameproof enclosure Removable connection cap Galvanically isolated RS 22 interface Description

More information

Multiturn absolute encoder

Multiturn absolute encoder SYNCHRON SERIELLES INTERFACE Multiturn absolute encoder Model Number Features Industrial standard housing Ø58 mm 30 Bit multiturn Data transfer up to 2 MBaud Optically isolated RS 422 interface Recessed

More information

Online data sheet DFS60B-S4PA00S74 DFS60 INCREMENTAL ENCODERS

Online data sheet DFS60B-S4PA00S74 DFS60 INCREMENTAL ENCODERS Online data sheet DFS60B-S4PA00S74 DFS60 A B C D E F Illustration may differ Ordering information Type Part no. DFS60B-S4PA00S74 1081183 Other models and accessories www.sick.com/dfs60 H I J K L M N O

More information

ABSOLUTE ROTARY ENCODER SSI PROGRAMMABLE

ABSOLUTE ROTARY ENCODER SSI PROGRAMMABLE Main Features - Compact and heavy-duty industrial model - Interface: Synchronous-serial (RS422/485) - Housing: 58 mm - Shaft: 6 or 10 mm - Resolution: Max. 25 Bit =,554,42 steps over 4,096 revolutions

More information

Absolute Encoders Multiturn

Absolute Encoders Multiturn The Sendix F36 multiturn with the patented Intelligent Scan Technology is an optical multiturn encoder in miniature format, without gears and with 00% insensitivity to magnetic fields. With a size of just

More information

Rotary Measuring Technology

Rotary Measuring Technology SSI or parallel interface Highest shock resistance on the market ( 2500 m/s2, 6 ms acc. to DIN IEC 68-2-27) Divisions: up to 16384 (14 bits), singleturn Housing Ø 58 mm IP 66 Various options (e.g. LATCH,

More information

LENORD. +BAUER... automates motion. GEL 295x Customer-specific precision encoder. Technical Information Version General information.

LENORD. +BAUER... automates motion. GEL 295x Customer-specific precision encoder. Technical Information Version General information. GEL 95x Customer-specific precision encoder LENORD +BAUER... automates motion. Technical Information Version 04- General information Extremly robust rotary encoder with stainless steel housing for measuring

More information

Absolute encoders - SSI Solid shaft with clamping or synchro flange Optical multiturn encoders up to 14 bit ST / 16 bit MT

Absolute encoders - SSI Solid shaft with clamping or synchro flange Optical multiturn encoders up to 14 bit ST / 16 bit MT Features Encoder multiturn / SSI Optical sensing method Resolution: max. singleturn 14 bit, multiturn 16 bit Clamping or synchro flange Electronic setting of zero point Counting direction input Available

More information

Online data sheet DFS60A-TEPZ00S09 DFS60 INCREMENTAL ENCODERS

Online data sheet DFS60A-TEPZ00S09 DFS60 INCREMENTAL ENCODERS Online data sheet DFS60A-TEPZ00S09 DFS60 A B C D E F H I J K L M N O P Q R S T Illustration may differ Detailed technical data Features Special device Specialty Ordering information Other models and accessories

More information

ABSOLUTE ROTARY ENCODER SSI

ABSOLUTE ROTARY ENCODER SSI Main Features - Compact and heavy-duty industrial model - Interface: Synchronous-serial (RS422/485) - Housing: 58 mm - Shaft: 6 or 10 mm - Resolution: Max. 25 Bit =,554,42 steps over 4,096 revolutions

More information

Multiturn absolute encoder

Multiturn absolute encoder SYNCHRON SERIELLES INTERFACE Multiturn absolute encoder Release date: 2016-07-12 16:14 Date of issue: 2016-07-12 t4917_eng.xml Model Number Features Industrial standard housing Ø58 mm 0 Bit multiturn Data

More information

Absolute encoders - SSI Solid shaft with clamping or synchro flange Optical multiturn encoders up to 14 bit ST / 16 bit MT

Absolute encoders - SSI Solid shaft with clamping or synchro flange Optical multiturn encoders up to 14 bit ST / 16 bit MT Features Encoder multiturn / SSI Optical sensing method Resolution: max. singleturn 14 bit, multiturn 16 bit Clamping or synchro flange Electronic setting of zero point Counting direction input Available

More information

DRS61: Incremental encoders, number of lines and zero pulse width freely programmable DRS60: Incremental Encoders with Zero-Pulse-Teach

DRS61: Incremental encoders, number of lines and zero pulse width freely programmable DRS60: Incremental Encoders with Zero-Pulse-Teach NEW DRS: Incremental encoders, number of lines and zero pulse width freely programmable DRS: s with Zero-Pulse-Teach Further highlights of this generation of encoders: Simple zero-pulse-teach by pressing

More information

Absolute encoders - SSI Shaft with clamping or synchro flange Optical multiturn encoders 14 bit ST / 12 bit MT

Absolute encoders - SSI Shaft with clamping or synchro flange Optical multiturn encoders 14 bit ST / 12 bit MT Features Encoder multiturn / SSI Optical sensing Resolution: singleturn 14 bit, multiturn 12 bit Clamping or synchro flange Electronic setting of zero point Counting direction input Suitable for high positive,

More information

Absolute Encoders Multiturn

Absolute Encoders Multiturn Absolute Encoders Multiturn Functional Safety, optical The absolute multiturn encoders Sendix 5863 SIL and 5883 SIL are perfectly suited for use in safety-related applications up to SIL3 according to DIN

More information

ABSOLUTE ROTARY ENCODER MULTI-TURN BIT PARALLEL

ABSOLUTE ROTARY ENCODER MULTI-TURN BIT PARALLEL Main Features - Compact and heavy-duty industrial model - Interface: Bit-parallel, push pull ΠShort circuit proof - Housing: 58 mm - Shaft: 6 or 10 mm - Resolution: Max. 25 Bit =,554,42 steps over 4,096

More information

Absolute encoders - SSI

Absolute encoders - SSI with through hollow shaft Features Encoder multiturn / SSI Optical sensing method Resolution: singleturn 14 bit, multiturn 12 bit Compact design Cost-efficient mounting High reliability by self-diagnostics

More information

Online data sheet. ACM60B-S1KE13x06 ACM60 ABSOLUTE ENCODERS

Online data sheet. ACM60B-S1KE13x06 ACM60 ABSOLUTE ENCODERS Online data sheet ACM60B-S1KE1x06 ACM60 A B C D E F H I J K L M N O P Q R S T Illustration may differ Detailed technical data Performance Number of steps per revolution Number of revolutions Ordering information

More information

LENORD. +BAUER... automates motion. Magnetic incremental encoder GEL 293 for heavy duty applications. Technical Information Version 04.

LENORD. +BAUER... automates motion. Magnetic incremental encoder GEL 293 for heavy duty applications. Technical Information Version 04. Magnetic incremental encoder GEL 293 for heavy duty applications LENORD +BAUER... automates motion. Technical Information Version 04.14 General information High-resolution magnetic incremental rotary encoder

More information

Magnetic absolute single-turn encoder BMSH MAGRES parallel

Magnetic absolute single-turn encoder BMSH MAGRES parallel Magnetic absolute single-turn encoder BMSH MAGRES parallel features robust single-turn encoder up to 9 bit parallel interface miniature housing zero-point programmable general data voltage supply 5 VDC

More information

Rotary Measurement Technology Absolute Encoders, Multiturn

Rotary Measurement Technology Absolute Encoders, Multiturn Mechanical drive Safety-LockTM High rotational speed -40 to 90 C IP Temperature High IP High shaft load capacity Shock/ vibration resistant Magnetic field proof Short-circuit proof Reverse polarity protection

More information

Absolute Encoders Singleturn

Absolute Encoders Singleturn The absolute singleturn encoders Sendix 5853 SIL and 5873 SIL are perfectly suited for use in safety-related applications up to SIL3 according to DIN EN ISO 6800-5- or PLe to DIN EN ISO 3849. The extra

More information

DGS 60, DGS 65 and DGS 66: Incremental Encoders for rough environmental conditions

DGS 60, DGS 65 and DGS 66: Incremental Encoders for rough environmental conditions , 5 and : s for rough environmental conditions elect your individual encoder - Possible product variants: and mm solid shafts with servo flange or face mount flange, through or blind hollow shafts with

More information

Absolute Encoders - Singleturn

Absolute Encoders - Singleturn The Sendix 5853 and Sendix 5873 singleturn encoders with SSI or BiSS interface and optical sensor technology can achieve a resolution of max. 7 bits. These encoders are also available with an optional

More information

Series BC 58. Absolute Rotary Encoder Series BC 58

Series BC 58. Absolute Rotary Encoder Series BC 58 Mechanical specifications Shaft diameter Shaft load 6 mm (synchro flange) 10 mm (clamping flange) 10/12 mm (blind hollow shaft) Series BC 58 E Absolute single- and multiturn rotary-encoder with solid shaft

More information

Incremental encoders 6

Incremental encoders 6 Incremental encoders ELECTRONIC GmbH Incremental encoders 6 6.1 Explanatory notes...6-3 6.2 Functional description...6-4 6.3 Applications...6-5 6.4 Assembly examples...6-6 6.5 Alternative designs...6-8

More information

Oil & Gas / Heavy Industry Type 2REX-A-NA-SSI

Oil & Gas / Heavy Industry Type 2REX-A-NA-SSI Oil & Gas / Heavy Industry Type 2REX-A-NA-SSI EN 60079 Electrical Specifications Encoder Type: Singleturn Resolution: Number of Revolutions: Supply Voltage: Typical Current Consumption: Accuracy: ± 0,35ᴼ

More information

Online data sheet AFS60B-S4PA AFS/AFM60 SSI ABSOLUTE ENCODERS

Online data sheet AFS60B-S4PA AFS/AFM60 SSI ABSOLUTE ENCODERS Online data sheet FS60-S4P032768 FS/FM60 SSI FS60-S4P032768 FS/FM60 SSI C D E F Ordering information Type Part no. FS60-S4P032768 1037483 Other models and accessories www.sick.com/fs_fm60_ssi Illustration

More information

LENORD. +BAUER... automates motion. GEL 2351 with current or voltage interface. Technical information Version General. Features.

LENORD. +BAUER... automates motion. GEL 2351 with current or voltage interface. Technical information Version General. Features. GEL 2351 with current or voltage interface LENORD +BAUER... automates motion. Technical information Version 201-11 General Single turn absolute rotary encoder with a resolution of 16 bits Magneto-resistive

More information

Absolute Encoders - Singleturn

Absolute Encoders - Singleturn The Sendix 5 and Sendix 7 singleturn encoders with SSI or BiSS-C interface and optical sensor technology can achieve a resolution of max. 7 bits. These encoders are also available with an optional SinCos

More information

Rotary Measuring Technology

Rotary Measuring Technology Our ATEX encoders now also carry approval for Dust Flameproof-enclosure type of construction with approval for Zone 1 and 21 ExII2GEExdIICT6 and ExII2DIP6xT85 C Shaft ø 12 mm One type for every situation:

More information

Online data sheet AFS60E-S1AA AFS/AFM60 SSI ABSOLUTE ENCODERS

Online data sheet AFS60E-S1AA AFS/AFM60 SSI ABSOLUTE ENCODERS Online data sheet FS0E-S0009 FS/FM0 SSI SOLUTE ENCODERS FS0E-S0009 FS/FM0 SSI SOLUTE ENCODERS C D E F Ordering information Type Part no. FS0E-S0009 0 Other models and accessories www.sick.com/fs_fm0_ssi

More information

Absolute encoders - SSI Solid shaft with clamping or synchro flange Optical multiturn encoders 18 bit ST / 12 bit MT

Absolute encoders - SSI Solid shaft with clamping or synchro flange Optical multiturn encoders 18 bit ST / 12 bit MT Features High resolution encoder multiturn / SSI Optical sensing method Resolution: singleturn 18 bit, multiturn 12 bit Electronic setting of zero point Counting direction input Available with additional

More information

NOVOTURN Multiturn Sensor non-contacting. Series RSM-2800

NOVOTURN Multiturn Sensor non-contacting. Series RSM-2800 NOVOTURN Multiturn Sensor non-contacting Series RSM-2800 Special features Non-contacting, magnetic Long life Electrical range 720 up to 5760 in 360 -steps available (2 to 16 turns) True-Power-On System:

More information

ABSOLUTE ROTARY ENCODER SSI

ABSOLUTE ROTARY ENCODER SSI Main Features - Compact and heavy-duty industrial model - Interface: Synchronous-serial (RS 422) - Housing: 58 mm - Shaft: 6 or 10 mm - Hollow shaft 12 mm - Blind hollow shaft 15 mm - Max. 65,56 steps

More information

NOVOHALL Rotary Sensor non-contacting. Series RSC2800 digital SSI, SPI, Incremental

NOVOHALL Rotary Sensor non-contacting. Series RSC2800 digital SSI, SPI, Incremental NOVOHALL Rotary Sensor non-contacting Series RSC2800 digital SSI, SPI, Incremental The RSC 2800 sensor utilizes a contactless magnetic measurement technology to determine the measured angle. Unlike conventional

More information

Online data sheet AFM60B-S4PC AFS/AFM60 SSI ABSOLUTE ENCODERS

Online data sheet AFM60B-S4PC AFS/AFM60 SSI ABSOLUTE ENCODERS Online data sheet FM60-S4PC032768 FS/FM60 SSI C D E F H I J K L M N O P Q R S T Ordering information Type Part no. FM60-S4PC032768 1037504 Other models and accessories www.sick.com/fs_fm60_ssi Illustration

More information

Online data sheet AFS60A-BJPA AFS/AFM60 SSI ABSOLUTE ENCODERS

Online data sheet AFS60A-BJPA AFS/AFM60 SSI ABSOLUTE ENCODERS Online data sheet FS0-JP FS/FM0 SSI FS0-JP FS/FM0 SSI C D E F H I J K L M N O P Q R S T Ordering information Type Part no. FS0-JP 09 Other models and accessories www.sick.com/fs_fm0_ssi Illustration may

More information

Express Delivery. Axial. Connection

Express Delivery. Axial. Connection HIGH RESOLUTION INCREMENTAL SOLID SHAFT ENCODER FOR INDUSTRIAL APPLICATIONS Resolution up to 50.000 pulses per turn External diameter 58 mm Shaft from Ø 6 to 12 mm Protection class IP67 according to DIN

More information

FVS58 singleturn absolute encoder. FVS58. Technical Product description data Incremental encoders special designs. Technical data

FVS58 singleturn absolute encoder. FVS58. Technical Product description data Incremental encoders special designs. Technical data absolute encoder Industrial standard housing Ø58 mm 1 Bit singleturn Output code: Gray and binary Short-circuit proof push-pull output Inputs for selection of counting direction, LATCH and PRESET Code

More information

ABSOLUTE ROTARY ENCODER SSI

ABSOLUTE ROTARY ENCODER SSI Main Features - Compact and heavy-duty industrial model - Interface: Synchronous -serial (RS 422) - Housing: 58 mm - Shaft: 6 or 10 mm - Hollow shaft 12 mm - Blind hollow shaft 15 mm - Max. 65,56 steps

More information

TECHNICAL DATASHEET Absolute Encoder AC 58 - BiSS / SSI

TECHNICAL DATASHEET Absolute Encoder AC 58 - BiSS / SSI Compact design: 50 mm length for single or multiturn Aids for start up and operation: diagnostic LED, preset key with optical response, status information Use of sine/ cosine signals for fast control task

More information

Electrical data Units FVS 58, FHS 58. Operating voltage (PELV) [VDC] Current consumption at 24 VDC [ma] 85

Electrical data Units FVS 58, FHS 58. Operating voltage (PELV) [VDC] Current consumption at 24 VDC [ma] 85 Parallel Singleturn bsolute Value Encoder Features 13-bit Singleturn High code change frequency Inputs for: - Selection of counting direction - Buffer memory (LTCH) - Multiplex operation (TRISTTE) Short-circuit

More information

Precision Encoder GEL with sine-wave output - for extremely harsh environments

Precision Encoder GEL with sine-wave output - for extremely harsh environments Precision Encoder GEL 295 - with sine-wave output - for extremely harsh environments Technical information version 08.0 -, - 5 ) 0 General information extremely robust encoder for measuring the rotational

More information

Measuring systems. 7/2 Overview. 7/3 Built-on optoelectronic rotary encoders 7/3 Introduction

Measuring systems. 7/2 Overview. 7/3 Built-on optoelectronic rotary encoders 7/3 Introduction Siemens AG 2010 Measuring systems /2 Overview /3 Built-on optoelectronic rotary encoders /3 Introduction /4 Incremental encoders /4 sin/cos 1 V pp /4 RS 422 (TTL) /4 HTL /4 RS 422 (TTL) double-track /

More information

Absolute multi-turn hollow shaft encoder BOMH Dignalizer SSI

Absolute multi-turn hollow shaft encoder BOMH Dignalizer SSI features high resolution multi-turn encoder up to - 8 bit single-turn - 8 bit multi-turn interface programmable permanent self-test reference point programmable general data voltage supply 5 VDC (05C)

More information

RM36. Rotation sensors RM36 Absolute rotary encoder

RM36. Rotation sensors RM36 Absolute rotary encoder Rotation sensors RM36 Absolute rotary encoder RM36 Description The RM36 is a high-speed magnetic rotary encoder designed for use in harsh industrial environments. The non-contact two-part design removes

More information

Online data sheet ACM36-L1K0-K01 ACS/ACM36 ABSOLUTE ENCODERS

Online data sheet ACM36-L1K0-K01 ACS/ACM36 ABSOLUTE ENCODERS Online data sheet ACM36-L1K0-K01 ACS/ACM36 ACM36-L1K0-K01 ACS/ACM36 A B C D E F H I J K L M N O P Q R S T Illustration may differ Detailed technical data Performance Number of steps per revolution Number

More information

Online data sheet. DBS60E-TECJD1024 DBS60 Core INCREMENTAL ENCODERS

Online data sheet. DBS60E-TECJD1024 DBS60 Core INCREMENTAL ENCODERS Online data sheet DS60ETECJD1024 DS60 Core C D E F H I J K L M N O P Q R S T Ordering information Type Part no. DS60ETECJD1024 DS60ETECJD1024 Other models and accessories www.sick.com/ds60_core Illustration

More information

Speed and position sensor MiniCoder GEL 2442

Speed and position sensor MiniCoder GEL 2442 Speed and position sensor MiniCoder GEL 2442 contactless, high-resolution, high speed Technical information version 01.09 Functional description Measurement of speed and position by proximity sensing of

More information

Product Information. RCN 2000 RCN 5000 RCN 8000 Absolute Angle Encoders for Safety-Related Applications

Product Information. RCN 2000 RCN 5000 RCN 8000 Absolute Angle Encoders for Safety-Related Applications Product Information RCN 2000 RCN 5000 RCN 8000 Absolute Angle Encoders for Safety-Related Applications September 2013 RCN 2000 series Absolute angle encoders for safety-related applications Safe absolute

More information

Lexium integrated drives

Lexium integrated drives Description ILp for CANopen, PROFIBUS DP, RS ILA with AC synchronous servo motor Description ILA comprise control electronics with a fieldbus interface for CANopen DS, PROFIBUS DP or RS and an AC synchronous

More information

Technical data. Functional safety related parameters MTTF d Mission Time (T M ) max. 140 ma Power consumption P 0. Voltage drop

Technical data. Functional safety related parameters MTTF d Mission Time (T M ) max. 140 ma Power consumption P 0. Voltage drop Release date: 2014-04-14 15: Date of issue: 2016-05-0 t102_eng.xml Model Number Features Industrial standard housing Ø58 mm 1 Bit singleturn Output code: gray and binary Short-circuit proof push-pull output

More information

Magnetic absolute multi-turn hollow shaft encoder BMMH MAGRES SSI

Magnetic absolute multi-turn hollow shaft encoder BMMH MAGRES SSI Magnetic absolute multi-turn hollow shaft encoder BMMH MAGRES SSI features robust multi-turn encoder up to - 2 bit single-turn resolution - 3 bit multi-turn resolution miniature housing zero point programmable

More information

DATASHEET ABSOLUTE MAGNETIC ROTARY ENCODER SSI

DATASHEET ABSOLUTE MAGNETIC ROTARY ENCODER SSI Robust rotary sensor based on reliable magnetic technology. Stainless steel housing capable to withstand extreme environmental conditions. Ideal suited for outdoor applications. Sturdy ball bearings for

More information

Technical data. General specifications. Measurement range min max. 360

Technical data. General specifications. Measurement range min max. 360 Model Number Features Very small housing High climatic resistance 12 Bit singleturn Analog output Surge and reverse polarity protection Description This absolute rotary encoder with internal magnetic sampling

More information

LENORD GEL BAUER

LENORD GEL BAUER GEL 2440 with square-wave output signals and internal interpolation LENORD +BAUER... automates motion. Technical information Version 2014-08 General The measuring system comprises a scanning unit MiniCODER

More information

Measuring systems. 6/2 Built-on optoelectronic rotary encoders 6/2 Introduction

Measuring systems. 6/2 Built-on optoelectronic rotary encoders 6/2 Introduction Siemens AG 2008 Measuring systems /2 Built-on optoelectronic rotary encoders /2 Introduction /2 Incremental encoders /3 TTL (RS 422) /3 sin/cos 1 V pp /3 HTL /3 TTL (RS 422) double-track / Absolute encoders

More information

NOVOHALL Rotary Sensor non-contacting. Series RSC-2800

NOVOHALL Rotary Sensor non-contacting. Series RSC-2800 NOVOHALL Rotary Sensor non-contacting Series RSC-2800 Special features Non-contacting, magnetic technology Measuring range up to 360 Available with push-on coupling or marked shaft Simple mounting Protection

More information

LENORD. +BAUER... automates motion. GEL 2444K PG Configurable rotational speed and position sensor with operating hours counter

LENORD. +BAUER... automates motion. GEL 2444K PG Configurable rotational speed and position sensor with operating hours counter GEL 2444K PG Configurable rotational speed and position sensor with operating hours counter LENORD +BAUER... automates motion. Technical information Version 2015-03 General The measuring system comprises

More information

T40B. Torque Flange. Special features. Data sheet. Overall concept

T40B. Torque Flange. Special features. Data sheet. Overall concept T40B Torque Flange Special features - Nominal (rated) torques 50 N m, 0 N m, 200 N m, 500 N m, 1 kn m, 2 kn m, 3 kn m, 5 kn m and kn m - Nominal rated rotational speed up to 24000 rpm (depending on nominal

More information

Rotary encoders. absolute / optical. Bright ideas in the measurement of rotation: robust, precise, versatile.

Rotary encoders. absolute / optical. Bright ideas in the measurement of rotation: robust, precise, versatile. Rotary encoders absolute / optical right ideas in the measurement of rotation: robust, precise, versatile. Absolute encoder WK02/1 Hollow shaft WK02/1 - robust single-turn angle encoder with through hollow

More information

Material: Weight: Bearing Life: Shaft Speed: Starting Torque: Mass Moment of Inertia: Shaft Loads:

Material: Weight: Bearing Life: Shaft Speed: Starting Torque: Mass Moment of Inertia: Shaft Loads: Shaft Encoder - Ø 50 mm Shaft: Ø 6 mm to Ø 12 mm Resolution up to 12.500 ppr IP 65 (IP 67 option) Formerly named 2R or 2R-3L Automation / Electrical Specifications Code: Resolution: Supply Voltage: Voltage:

More information

DG 60 L Incremental Encoder

DG 60 L Incremental Encoder Incremental Encoder Features Incremental encoder with 60 mm outer diameter ugged die-cast aluminum housing Quadrature output with reference marker, complementary output signals Protection to IP 67 Square

More information

Incremental encoder MiniCoder GEL 243

Incremental encoder MiniCoder GEL 243 Incremental encoder MiniCoder GEL 243 with sinewave and squarewave output Technical information version 10.06 General information contactless measurement of rotational motion of target wheels with modules

More information

ABSOLUTE ROTARY ENCODER DEVICE NET

ABSOLUTE ROTARY ENCODER DEVICE NET Main Features - Compact and heavy-duty industrial model - Interface: CAN according to Device Net - Housing: 8 mm - Shaft: 6 or 0 mm - Resolution: Max. 2 Bit =,,2 steps over,096 revolutions - Code: Binary

More information

Product Overview. Rotary Encoders with Optimized Scanning

Product Overview. Rotary Encoders with Optimized Scanning Product Overview Rotary Encoders with Optimized Scanning November 2006 Rotary encoders for electrical drives are subject to high requirements: they are expected to function reliably and provide dependable

More information

Standard Industrial types RI 36-H

Standard Industrial types RI 36-H Miniature industry encoder for high number of pulses Short mounting length Easy mounting procedure Applications: motors, machine tools, robots, automated SMD equipment NUMBER OF PULSES 5 / 0 / 0 / 5 /

More information

Product Information. ECN 413 ECN 425 ERN 421 ERN 487 Rotary Encoders for Drive Control in Elevators

Product Information. ECN 413 ECN 425 ERN 421 ERN 487 Rotary Encoders for Drive Control in Elevators Product Information ECN 413 ECN 425 ERN 421 ERN 487 Rotary Encoders for Drive Control in Elevators October 2007 ECN/ERN 400 Series Rotary Encoders with Integral Bearings for Elevator Technology Simple

More information

Product Information. EQN 1337 F Absolute Rotary Encoder with Tapered Shaft for Fanuc Controls with i Interface

Product Information. EQN 1337 F Absolute Rotary Encoder with Tapered Shaft for Fanuc Controls with i Interface Product Information EQN 1337 F Absolute Rotary Encoder with Tapered Shaft for Fanuc Controls with i Interface 11/2017 EQN 1337 F Rotary encoders for absolute position values Installation diameter 65 mm

More information

Series CE-65-S... INFO

Series CE-65-S... INFO Absolute encoders ELECTRONIC GmbH Absolute encoders 1 Explanatory notes- 2 Functional description-6 3 Applications -7 4 Assembly instructions-8 Alternative designs -10 1 Encoder with integrated coupling

More information

Temposonics. R-Series SSI. Absolute, Non-Contact Position Sensors. Temposonics RP and RH Stroke length mm. Perfect data processing 0.

Temposonics. R-Series SSI. Absolute, Non-Contact Position Sensors. Temposonics RP and RH Stroke length mm. Perfect data processing 0. R-Series Temposonics Absolute, Non-Contact Position Sensors R-Series Temposonics RP and RH 25 7600 mm Perfect data processing 0.5 μm Rugged industrial sensor Linear and absolute measurement LEDs for sensor

More information

Product Information. ERN 1085 Incremental Rotary Encoder with Z1 Track

Product Information. ERN 1085 Incremental Rotary Encoder with Z1 Track Product Information ERN 1085 Incremental Rotary Encoder with Z1 Track 02/2018 ERN 1085 Rotary encoder with mounted stator coupling Compact dimensions Blind hollow shaft 6 mm Z1 track for sine commutation

More information

T40FM. Data Sheet. Torque flange. Special features. Overall concept. B en

T40FM. Data Sheet. Torque flange. Special features. Overall concept. B en T40FM Torque flange Special features Data Sheet - Nominal (rated) torque: 15 kn m, 20 kn m, 25 kn m, 30 kn m, 40 kn m, 50 kn m, 60 kn m, 70 kn m and 80 kn m - Nominal (rated) rotational speed up to 8000

More information

IP 251 Universal Signal Converter SSI parallel RS232 parallel SSI RS232

IP 251 Universal Signal Converter SSI parallel RS232 parallel SSI RS232 control motion interface ELEKTRO-TRADING sp. z o.o Tel. +48 (0-32) 734-55-72 Tel/Fax +48 (0-32) 734-55-70 E-Mail et@elektro-trading.com.pl http://www.elektro-trading.com.pl IP 251 Universal Signal Converter

More information

SIMPLY PRECISE PRELIMINARY. Preliminary product overview - LAK encoder. LAK 1 Absolute linear encoder with signal control

SIMPLY PRECISE PRELIMINARY. Preliminary product overview - LAK encoder. LAK 1 Absolute linear encoder with signal control PRELIMINARY Preliminary product overview - LAK encoder LAK 1 Absolute linear encoder with signal control 2 Index 1. Overview 3 2. Applications 3 3. Technical data 4 4. General specifications 5 5. Dimensions

More information

ENCODER. SSI Multiturn. Series , Key-Features: Content:

ENCODER. SSI Multiturn. Series , Key-Features: Content: ENCOER SSI Multiturn Series 8.5863, 8.5883 Content: Order Code Shaft... Order Code Hollow Shaft...3 Order Code Blind Hollow Shaft...3 Connection...4 Technical rawing...5 Technical ata...8 Key-Features:

More information

Product Information. EBI 1135 Absolute Rotary Encoder, Multiturn Feature via Battery-Buffered Revolution Counter

Product Information. EBI 1135 Absolute Rotary Encoder, Multiturn Feature via Battery-Buffered Revolution Counter Product Information EBI 1135 Absolute Rotary Encoder, Multiturn Feature via Battery-Buffered Revolution Counter December 2012 EBI 1135 Inductive rotary encoder without integral bearing for integration

More information

0.04 mm Distance/revolution mm ±0.05% f. s.; ±0.01% f. s. as option. Measurement range (in mm) 2500 (smaller measurement ranges included)

0.04 mm Distance/revolution mm ±0.05% f. s.; ±0.01% f. s. as option. Measurement range (in mm) 2500 (smaller measurement ranges included) WS58C Absolute Encoder Output Very compact position sensor Measuring range 0... 2500 mm With absolute encoder output High precision linearity up to ±0.01 % full scale Specifications Output for 12 bit/revolution

More information

T40FH. Torque flange. Special features. Data sheet

T40FH. Torque flange. Special features. Data sheet T40FH Torque flange Special features - Nominal (rated) torques: 100kNm, 125kNm, 150kNm, 200kNm, 250kNm, 300kNm - Nominal (rated) rotational speed of 2000 rpm up to 3000 rpm - Compact design - Version for

More information

NOVOHALL Rotary Sensor touchless transmissive. Series RFX-6900

NOVOHALL Rotary Sensor touchless transmissive. Series RFX-6900 NOVOHALL Rotary Sensor touchless transmissive Series RFX-6900 Special features Very robust design to extreme environmental conditions Touchless hall technology Electrical range up to 360, in single and

More information

Power supply voltage Output configuration Output code Resolution (pulses/rotation) Connection method Model

Power supply voltage Output configuration Output code Resolution (pulses/rotation) Connection method Model 60-mm-dia. Encoder Rugged Encoder for High-precision Detection of Automatic Machine Timing Rugged construction with the highest shaft loading. Radial: 120 N, Thrust: 50 N IP65f water- and oil-proof construction.

More information

Incremental EX and Stainless Steel Encoders

Incremental EX and Stainless Steel Encoders Incremental EX and Stainless Steel Encoders RX 70-TI / RX 71-TI (Stainless) RI 59 explosion-proof according to EX II 2 G/D EEX d IIC T6/T4 highest operating safety applications e.g. lacquering lines, surface

More information

KINAX 2W2 Programmable Transmitter for Angular Position

KINAX 2W2 Programmable Transmitter for Angular Position Application The KINAX 2W2 (Figs. 2 and 3) converts the angular position of a shaft into a load independent direct current signal, proportional to the angular position. The unit is contact free and has

More information

Temposonics. R-Series SSI. Absolute, Non-Contact Position Sensors. Temposonics RP and RH Measuring length mm. Perfect data processing I 7 I

Temposonics. R-Series SSI. Absolute, Non-Contact Position Sensors. Temposonics RP and RH Measuring length mm. Perfect data processing I 7 I Temposonics Absolute, Non-Contact Position Sensors R-Series Temposonics RP and RH Measuring length 5-7600 mm Perfect data processing 0,5 µm Rugged Industrial Sensor Linear and Absolute Measurement LEDs

More information

Features. Applications. Plastic Housing. Sensor PCB Assembly. Plastic Hub. Plastic Base Plate. 2 x screws

Features. Applications. Plastic Housing. Sensor PCB Assembly. Plastic Hub. Plastic Base Plate. 2 x screws AEAT61/612 Magnetic Encoder 1 or 12 bit Angular Detection Device Data Sheet Description Avago Technologies AEAT6xx series of magnetic encoders provides an integrated solution for angular detection. With

More information

Diameter ø50mm Shaft type Absolute Multi-turn Rotary Encoder

Diameter ø50mm Shaft type Absolute Multi-turn Rotary Encoder Dia ø50mm Shaft type Absolute Multi-turn otary Encoder Features Compact size of dia ø50mm Parallel data / SSI data transmission type Total 23bit resolution(8388608 divisions) of 10bit single-turn(1024

More information

MHAD 50 - HDmag. Features

MHAD 50 - HDmag. Features Magnetic sensing, hollow shaft 30 mm MHAD 50 with cable Features Absolute encoder with magnetic sensing and without bearings Absolute resolution max. 16 bit singleturn Additional incremental signals Robust

More information