9- and 11-Channel, Muxed Input LCD Reference Buffers AD8509/AD8511
|
|
|
- Silas Kelley
- 5 years ago
- Views:
Transcription
1 9- and -Channel, Muxed Input LCD Reference Buffers AD8509/AD85 FEATURES Single-supply operation: 3.3 V to 6.5 V High output current: 300 ma Low supply current: 6 ma Stable with 000 pf loads Pin compatible with LMC6009 Pin compatible with CL-FP63 48-lead, Pb-free TSSOP/LFCSP packages APPLICATION LCD line inversion gamma references GENERAL DESCRIPTION The AD8509 and AD85 are 9-channel and -channel LCD reference buffers, respectively, designed to drive 64 gray scale column drivers. Each buffer has an A/B input to select between two voltages for LCD displays. These buffers drive the resistor ladders of LCD column drivers for gamma correction. The LCD drivers have higher slew rates and higher output drive currents than similar competitive parts. This increases the stability of the reference ladder, resulting in better gray scale and visual performance. The AD8509 and AD85 are specified over the 40 C to +85 C temperature range. They are available in 48-lead, Pb-free TSSOP packages in tape and reel. Additionally, the ADD85 is available in a 48-lead, Pb-free LFCSP package INA 4 45 INB 5 44 V CC INA 6 43 GND INB 7 4 VO INA3 8 4 VO AD8509 INB VO3 TOP VIEW INA4 0 (Not to Scale) 39 VO4 INB4 38 V CC INA5 37 GND INB VO5 INA VO6 INB VO7 INA VO8 INB7 7 3 VO9 INA8 8 3 GND INB V CC INA9 0 9 A/B INB PIN CONFIGURATIONS 48 INA 47 VO INB 3 46 INA 4 45 INB 5 44 V CC INA GND INB3 7 4 VO INA4 8 4 VO3 AD85 INB VO4 TOP VIEW INA5 0 (Not to Scale) 39 VO5 INB5 38 V CC INA6 37 GND INB VO6 INA VO7 INB VO8 INA VO9 INB8 7 3 VO0 INA9 8 3 GND INB V CC INA0 0 9 A/B INB0 8 7 INA 3 6 VO INB 4 5 = NO CONNECT = NO CONNECT Figure. AD8509 and AD85 48-Lead TSSOP (RV Suffix) INB INA INB INA VO V CC GND FUTIONAL BLOCK DIAGRAM INA VO INB INA VO INB INA INA3 INB3 INA4 3 INB4 4 INA5 5 INB5 6 INA6 7 INB6 8 INA7 9 INB7 0 INA8 INB8 PIN INDICATOR AD85 TOP VIEW (Not to Scale) 36 VO 35 VO3 34 VO4 33 VO5 3 V CC 3 GND 30 VO6 9 VO7 8 VO8 7 VO9 6 VO0 5 GND INB VO = NO CONNECT A/B Figure INA9 INB9 INA0 INB0 INA INB VO A/B V CC Figure 3. AD85 48-Lead LFCSP Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 906, Norwood, MA , U.S.A. Tel: Fax: Analog Devices, Inc. All rights reserved.
2 TABLE OF CONTENTS Features... Application... General Description... Functional Block Diagram... Pin Configurations... Revision History... Specifications... 3 Electrical Characteristics... 3 Absolute Maximum Ratings...4 Thermal Resistance...4 ESD Caution...4 Pin Configurations and Function Descriptions...5 Typical Performance Characteristics...6 Applications...8 Outline Dimensions...9 Ordering Guide...9 REVISION HISTORY /06 Rev. C Added LFCSP Package...Universal Added Pin Configurations and Function Descriptions Section... 5 Updated Outline Dimensions... 9 Changes to Ordering Guide... 9 /05 Rev. A to Rev. B Changed Maximum Operating Voltage...Universal Change to Features List... Changes to Specifications Table... 3 Changes to Ordering Guide /04 Rev. 0 to Rev. A Format Updated...Universal Added Pb-Free Part...Universal Changed Temperature Range...Universal Changed Applications Section... Changes to Ordering Guide...8 0/97 Revision 0: Initial Version Rev. C Page of
3 SPECIFICATIONS ELECTRICAL CHARACTERISTICS VS = 5 V, TA = 5 C, unless otherwise noted. AD8509/AD85 Table. Parameter Symbol Conditions Min Typ Max Unit INPUT CHARACTERISTICS Offset Voltage VOS 0 mv Input Bias Current IB 50 na Voltage Gain AVO V/V OUTPUT CHARACTERISTICS Output Voltage High VOH ILOAD = +0 ma 4.8 V Output Voltage Low VOL ILOAD = 0 ma 00 mv Output Short-Circuit Current ISC ma POWER SUPPLY Load Regulation VIN = 0.5 V to 4.5 V, ISOURCE = 0 ma 7 mv VIN = 0.5 V to 4.5 V, ISINK = 0 ma 7 mv Supply Current ISY AD8509, VIN =.5 V 8.5 ma ISY AD85, VIN =.5 V 0 ma Supply Voltage Range VS V DYNAMIC PERFORMAE Slew Rate CL = 5 pf 7 V/μs RL = 50 Ω 6. V/μs Settling Time ts IDC = 3 ma (sink/source) 3 6 μs LOGIC INPUT CHARACTERISTICS Input Current Low IIL.0 μa Input Current High IIH.5 μa Input Voltage Low VIL 0.8 V Input Voltage High VIH.0 V Rev. C Page 3 of
4 ABSOLUTE MAXIMUM RATINGS Table. Parameter Supply Voltage Input Voltage Storage Temperature Range TSSOP (RV-48) Operating Temperature Range Junction Temperature Range TSSOP (RV-48) Package Rating 7 V GND to VS Lead Temperature Range (Soldering, 60 sec) 300 C 65 C to +50 C 40 C to +85 C 65 C to +50 C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. THERMAL RESISTAE θja is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Table 3. Thermal Resistance Package Type θja θjc Unit 48-Lead, Pb-Free SSOP (RV-48) 5 4 C/W 48-Lead, Pb-Free LFCSP (CP-48-) 5 9 C/W Table 4. MUX Function A/B Select Logic High Logic Low Input INAx INBx ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. C Page 4 of
5 PIN CONFIGURATIONS AND FUTION DESCRIPTIONS 3 INA INB 5 44 V CC INA 6 43 GND INB 7 4 VO INA3 8 4 VO AD8509 INB VO3 TOP VIEW INA4 0 (Not to Scale) 39 VO4 INB4 38 V CC INA5 INB5 3 INA6 4 INB6 5 INA7 6 INB7 7 INA8 8 INB8 9 INA9 0 INB9 3 4 = NO CONNECT 37 GND 36 VO5 35 VO6 34 VO7 33 VO8 3 VO9 3 GND 30 V CC 9 A/B Figure 4. AD Lead TSSOP (RV Suffix) INA INB 3 INA VO INB 5 44 V CC INA GND INB3 7 4 VO INA4 8 4 VO3 AD85 INB VO4 TOP VIEW INA5 0 (Not to Scale) 39 VO5 INB5 38 V CC INA6 INB6 3 INA7 4 INB7 5 INA8 6 INB8 7 INA9 8 INB9 9 INA0 0 INB0 INA 3 INB 4 = NO CONNECT 37 GND 36 VO6 35 VO7 34 VO8 33 VO9 3 VO0 3 GND 30 V CC 9 A/B VO 5 Figure 5. AD85 48-Lead TSSOP (RV Suffix) INB INA INB INA VO V CC GND INA3 INB3 INA4 3 INB4 4 INA5 5 INB5 6 INA6 7 INB6 8 INA7 9 INB7 0 INA8 INB8 PIN INDICATOR AD85 TOP VIEW (Not to Scale) 36 VO 35 VO3 34 VO4 33 VO5 3 V CC 3 GND 30 VO6 9 VO7 8 VO8 7 VO9 6 VO0 5 GND = NO CONNECT INA9 INB9 INA0 INB0 INA INB VO A/B V CC Figure 6. AD85 (48-Lead LFCSP) Table 5. Pin Function Descriptions Pin No. AD8509 (TSSOP) AD85 (TSSOP) AD85 (LFCSP) Mnemonic Description 4, 6, 8, 0,, 4, 6, 8, 0, 4, 6, 8, 0,, 4, 6, 8, 0, 3, 3, 5, 7, 9,, 3, 5, 7, 43, 45 INAx MUX Input 5, 7, 9,, 3, 5, 7, 9, 3, 5, 7, 9,, 3, 5, 7, 9,, 4, 4, 6, 8, 0,, 4, 6, 9, 44, 46 INBx MUX Input 3 to 36, 39 to 4 6, 3 to 36, 39 to 4, 47 0, 6 to 30, 33 to 36, 4 VOx MUX Output 9 9 A/B Input Selection Pin 30, 38, 44 30, 38, 44 4, 3, 40 Vcc Bias 3, 37, 43 3, 37, 43 5, 3, 39 GND Ground to 3, to 8, 45 to 48,, 5 7, 8, 45, 46, 48 8,, 3, 37, 38, 4, 47, 48 No Connection Rev. C Page 5 of
6 TYPICAL PERFORMAE CHARACTERISTICS 0 9 R L =NOLOAD k T A =5 C SUPPLY CURRENT (ma) Δ OUTPUT VOLTAGE (mv) 00 0 SOURCE SINK TEMPERATURE ( C) Figure 7. Supply Current vs. Temperature LOAD CURRENT (ma) Figure 9. Output Voltage to Supply Rail vs. Load Current T A =5 C R L =NOLOAD T A = 5 C R L =NOLOAD C L =5pF SUPPLY CURRENT (ma) AD8509 AD COMMON-MODE VOLTAGE (V) Figure 8. Supply Current vs. Common-Mode Voltage mV.5V Figure 0. Large Signal Transient Response Rising Rev. C Page 6 of
7 T A =5 C R L =NOLOAD C L = 5pF T A = 5 C R L = 50Ω C L = 5pF 60mV.5V mV.5V Figure. Large Signal Transient Response Falling Figure 3. Large Signal Transient Response Falling T A =5 C R L = 50Ω C L = 5pF 60mV.5V Figure. Large Signal Transient Response Rising Rev. C Page 7 of
8 APPLICATIONS The AD8509 and AD85 are CMOS buffers with A/B inputs that are used to select between two different reference voltages set up by an external resistor ladder. Input bias currents are orders of magnitude less than competitive parts. This allows very large resistor ladders to be used to save supply current. A guaranteed value of 50 na is much higher than actual values and is limited by leakage in the test system. Buffer outputs are designed to drive resistive loads. They are also stable with capacitive loads, so no resistors should be used in series with these outputs to attain the best display performance. Outputs have high slew rates and 6 μs settling times. Each output can deliver a minimum of 0 ma, assuring fast response to varying loads. The AD8509 is a 9-channel buffer and is similar to the LMC6009 in functionality. The AD85 is an -channel buffer similar to the CL-FP63. However, the control to select either 9- or -channel operation, the EN_ pin of the CL-FP63, is not available on the AD85. If 9-channel operation is desired, use the AD8509. Power supply pins on the AD8509 and AD85 have multiple ground and VCC connections. Because of the high peak currents that these buffers can deliver, it is strongly recommended to connect all of the ground and VCC pins, and suitably bypass the VCC pins. Rev. C Page 8 of
9 OUTLINE DIMENSIONS BSC 4 PIN.0 MAX BSC SEATING PLANE COMPLIANT TO JEDEC STANDARDS MO-53-ED Figure Lead Thin Shrink Small Outline Package [TSSOP] (RV-48) Dimensions shown in millimeters 7.00 BSC SQ PIN INDICATOR MAX MAX 0.8 PIN INDICATOR TOP VIEW 6.75 BSC SQ EXPOSED PAD (BOTTOM VIEW) SQ MAX SEATING PLANE 0.80 MAX 0.65 TYP 0.50 BSC MAX 0.0 NOM COPLANARITY 0.0 REF REF MIN COMPLIANT TO JEDEC STANDARDS MO-0-VKKD- Figure Lead Lead Frame Chip Scale Package [LFCSP_VQ] 7 mm x 7 mm Body, Very Thin Quad (CP-48-) Dimensions shown in millimeters ORDERING GUIDE Model Temperature Range Package Description Package Option AD8509ARU-REEL 40 C to +85 C 48-Lead Thin Shrink Small Outline Package [TSSOP] RV-48 AD8509ARUZ-REEL 40 C to +85 C 48-Lead Thin Shrink Small Outline Package [TSSOP] RV-48 AD85ARU-REEL 40 C to +85 C 48-Lead Thin Shrink Small Outline Package [TSSOP] RV-48 AD85ARUZ-REEL 40 C to +85 C 48-Lead Thin Shrink Small Outline Package [TSSOP] RV-48 AD85ACPZ-REEL 40 C to +85 C 48-Lead Lead Frame Chip Scale Package [LFCSP_VQ] CP-48- All models only available in,500-piece reels. Z = Pb-free part. Rev. C Page 9 of
10 NOTES Rev. C Page 0 of
11 NOTES Rev. C Page of
12 NOTES 006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C /06(C) Rev. C Page of
AD864/AD8642/AD8643 TABLE OF CONTENTS Specifications... 3 Electrical Characteristics... 3 Absolute Maximum Ratings... 5 ESD Caution... 5 Typical Perfo
FEATURES Low supply current: 25 µa max Very low input bias current: pa max Low offset voltage: 75 µv max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output Unity-gain
10-Channel Gamma Buffer with VCOM Driver ADD8710
1-Channel Gamma Buffer with VCOM Driver ADD871 FEATURES Single-supply operation: 4.5 V to 18 V Upper/lower buffers swing to VS/GND Gamma continuous output current: >1 ma VCOM peak output current: 25 ma
Low Power, Rail-to-Rail Output, Precision JFET Amplifiers AD8641/AD8642/AD8643
Data Sheet Low Power, Rail-to-Rail Output, Precision JFET Amplifiers AD864/AD8642/AD8643 FEATURES Low supply current: 25 μa max Very low input bias current: pa max Low offset voltage: 75 μv max Single-supply
AD8613/AD8617/AD8619. Low Cost Micropower, Low Noise CMOS Rail-to-Rail, Input/Output Operational Amplifiers PIN CONFIGURATIONS FEATURES APPLICATIONS
Low Cost Micropower, Low Noise CMOS Rail-to-Rail, Input/Output Operational Amplifiers FEATURES Offset voltage: 2.2 mv maximum Low input bias current: pa maximum Single-supply operation:.8 V to 5 V Low
Micropower Precision CMOS Operational Amplifier AD8500
Micropower Precision CMOS Operational Amplifier AD85 FEATURES Supply current: μa maximum Offset voltage: mv maximum Single-supply or dual-supply operation Rail-to-rail input and output No phase reversal
12-Channel Gamma Buffers with VCOM and Regulator ADD8707 FEATURES 12 precision gamma reference outputs Mask-programmable gamma resistors: 0.2% resolut
12-Channel Gamma Buffers with VCOM and Regulator FEATURES 12 precision gamma reference outputs Mask-programmable gamma resistors:.2% resolution and.1% accuracy Mask programmable voltage regulator:.4% accuracy
OBSOLETE. Charge Pump Regulator for Color TFT Panel ADM8830
FEATURES 3 Output Voltages (+5.1 V, +15.3 V, 10.2 V) from One 3 V Input Supply Power Efficiency Optimized for Use with TFT in Mobile Phones Low Quiescent Current Low Shutdown Current (
0.8% Accurate Quad Voltage Monitor ADM1184
.8% Accurate Quad Voltage Monitor ADM1184 FEATURES Powered from 2.7 V to 5.5 V on the VCC pin Monitors 4 supplies via.8% accurate comparators 4 inputs can be programmed to monitor different voltage levels
Zero Drift, Digitally Programmable Instrumentation Amplifier AD8231-EP OP FUNCTIONAL BLOCK DIAGRAM FEATURES ENHANCED PRODUCT FEATURES
Zero Drift, Digitally Programmable Instrumentation Amplifier AD8231-EP FEATURES Digitally/pin-programmable gain G = 1, 2, 4, 8, 16, 32, 64, or 128 Specified from 55 C to +125 C 5 nv/ C maximum input offset
Precision, Low Noise, CMOS, Rail-to-Rail, Input/Output Operational Amplifiers AD8605/AD8606/AD8608
Precision, Low Noise, CMOS, Rail-to-Rail, Input/Output Operational Amplifiers AD8605/AD8606/AD8608 FEATURES Low offset voltage: 65 μv maximum Low input bias currents: pa maximum Low noise: 8 nv/ Hz Wide
Quad 7 ns Single Supply Comparator AD8564
Quad 7 ns Single Supply Comparator AD8564 FEATURES 5 V single-supply operation 7 ns propagation delay Low power Separate input and output sections TTL/CMOS logic-compatible outputs Wide output swing TSSOP,
FET Drive Simple Sequencers ADM6819/ADM6820
FET Drive Simple Sequencers ADM6819/ADM682 FEATURES Single chip enables power supply sequencing of two supplies On-board charge pump fully enhances N-channel FET Adjustable primary supply monitor to.618
Low Power, Precision, Auto-Zero Op Amps AD8538/AD8539 FEATURES Low offset voltage: 13 μv maximum Input offset drift: 0.03 μv/ C Single-supply operatio
Low Power, Precision, Auto-Zero Op Amps FEATURES Low offset voltage: 3 μv maximum Input offset drift:.3 μv/ C Single-supply operation: 2.7 V to 5.5 V High gain, CMRR, and PSRR Low input bias current: 25
TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... 2 Specifications... 3 Absolute Maximum
FEATURES Offset voltage: 2.5 mv maximum Single-supply operation: 2.7 V to 5.5 V Low noise: 8 nv/ Hz Wide bandwidth: 24 MHz Slew rate: V/μs Short-circuit output current: 2 ma No phase reversal Low input
16 V, 4 MHz RR0 Amplifiers AD8665/AD8666/AD8668
6 V, MHz RR Amplifiers AD8665/AD8666/AD8668 FEATURES Offset voltage:.5 mv max Low input bias current: pa max Single-supply operation: 5 V to 6 V Dual-supply operation: ±.5 V to ±8 V Low noise: 8 nv/ Hz
15 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP
5 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +25 C) Controlled manufacturing baseline
Programmable Low Voltage 1:10 LVDS Clock Driver ADN4670
Data Sheet Programmable Low Voltage 1:10 LVDS Clock Driver FEATURES FUNCTIONAL BLOCK DIAGRAM Low output skew
Low Cost JFET Input Operational Amplifiers ADTL082/ADTL084
Low Cost JFET Input Operational Amplifiers ADTL/ADTL FEATURES TL/TL compatible Low input bias current: pa maximum Offset voltage 5.5 mv maximum (ADTLA/ADTLA) 9 mv maximum (ADTLJ/ADTLJ) ±5 V operation Low
AD8603/AD8607/AD8609. Precision Micropower, Low Noise CMOS Rail-to-Rail Input/Output Operational Amplifiers
Precision Micropower, Low Noise CMOS Rail-to-Rail Input/Output Operational Amplifiers FEATURES Low offset voltage: μv max Low input bias current: 1 pa max Single-supply operation: 1.8 V to 5 V Low noise:
Dual, Ultralow Distortion, Ultralow Noise Op Amp AD8599
Dual, Ultralow Distortion, Ultralow Noise Op Amp FEATURES Low noise: 1 nv/ Hz at 1 khz Low distortion: 5 db THD @ khz
Continuous Wave Laser Average Power Controller ADN2830
a FEATURES Bias Current Range 4 ma to 200 ma Monitor Photodiode Current 50 A to 1200 A Closed-Loop Control of Average Power Laser and Laser Alarms Automatic Laser Shutdown, Full Current Parameter Monitoring
Single 0.275% Comparator and Reference with Dual Polarity Outputs ADCMP361
Data Sheet FEATURES mv ±.275% threshold Supply range:.7 V to 5.5 V Low quiescent current: 6.5 µa typical Input range includes ground Internal hysteresis: 9.3 mv typical Low input bias current: ±5 na maximum
General-Purpose CMOS Rail-to-Rail Amplifiers AD8541/AD8542/AD8544
General-Purpose CMOS Rail-to-Rail Amplifiers AD854/AD8542/AD8544 FEATURES Single-supply operation: 2.7 V to 5.5 V Low supply current: 45 μa/amplifier Wide bandwidth: MHz No phase reversal Low input currents:
Ultraprecision, 36 V, 2.8 nv/ Hz Dual Rail-to-Rail Output Op Amp AD8676
FEATURES Very low voltage noise 2.8 nv/ Hz @ khz Rail-to-rail output swing Low input bias current: 2 na maximum Very low offset voltage: 2 μv typical Low input offset drift:.6 μv/ C maximum Very high gain:
Dual Low Power 1.5% Comparator With 400 mv Reference ADCMP670
Dual Low Power.5% Comparator With mv Reference ADCMP67 FEATURES FUNCTIONAL BLOCK DIAGRAM mv ±.5% threshold Supply range:.7 V to 5.5 V Low quiescent current: 6.5 μa typical Input range includes ground Internal
Low Voltage, 400 MHz, Quad 2:1 Mux with 3 ns Switching Time ADG774A
Low Voltage, 4 MHz, Quad 2:1 Mux with 3 ns Switching Time FEATURES Bandwidth: >4 MHz Low insertion loss and on resistance: 2.2 Ω typical On resistance flatness:.3 Ω typical Single 3 V/5 V supply operation
Dual/Quad Low Power, High Speed JFET Operational Amplifiers OP282/OP482
Dual/Quad Low Power, High Speed JFET Operational Amplifiers OP22/OP42 FEATURES High slew rate: 9 V/µs Wide bandwidth: 4 MHz Low supply current: 2 µa/amplifier max Low offset voltage: 3 mv max Low bias
Quad SPDT ±15 V/+12 V Switches ADG1334
Quad SPT ±15 V/+12 witches AG1334 FEATURES 33 V supply range 13 Ω on resistance Fully specified at ±15 V/+12 V 3 V logic compatible inputs Rail-to-rail operation Break-before-make switching action 2-lead
ADG1606/ADG Ω RON, 16-Channel, Differential 8-Channel, ±5 V,+12 V,+5 V, and +3.3 V Multiplexers FEATURES FUNCTIONAL BLOCK DIAGRAMS
4.5 Ω RON, 6-Channel, Differential 8-Channel, ±5 V,+2 V,+5 V, and +3.3 V Multiplexers ADG66/ADG67 FEATURES 4.5 Ω typical on resistance. Ω on resistance flatness ±3.3 V to ±8 V dual supply operation 3.3
Single and Dual, Ultralow Distortion, Ultralow Noise Op Amps AD8597/AD8599 PIN CONFIGURATIONS FEATURES APPLICATIONS
Single and Dual, Ultralow Distortion, Ultralow Noise Op Amps FEATURES Low noise:. nv/ Hz at khz Low distortion: db THD @ khz Input noise,. Hz to Hz:
DC to 1000 MHz IF Gain Block ADL5530
DC to MHz IF Gain Block ADL3 FEATURES Fixed gain of 6. db Operation up to MHz 37 dbm Output Third-Order Intercept (OIP3) 3 db noise figure Input/output internally matched to Ω Stable temperature and power
Low Cost JFET Input Operational Amplifiers ADTL082/ADTL084
Preliminary Technical Data FEATURES TL082 / TL08 compatible Low input bias current: 0 pa max Offset voltage: 5mV max (ADTL082A/ADTL08A) 9 mv max (ADTL082/ADTL08) ±5 V to ±5 V operation Low noise: 5 nv/
Comparators and Reference Circuits ADCMP350/ADCMP354/ADCMP356
Data Sheet Comparators and Reference Circuits ADCMP35/ADCMP354/ADCMP356 FEATURES Comparators with.6 V on-chip references Output stages Open-drain active low (ADCMP35) Open-drain active high (ADCMP354)
Quad Low Offset, Low Power Operational Amplifier OP400
Quad Low Offset, Low Power Operational Amplifier OP4 FEATURES Low input offset voltage 5 μv max Low offset voltage drift over 55 C to 25 C,.2 pv/ C max Low supply current (per amplifier) 725 μa max High
Logic Controlled, High-Side Power Switch with Reverse Current Blocking ADP195
Data Sheet Logic Controlled, High-Side Power Switch with Reverse Current Blocking ADP95 FEATURES Ultralow on resistance (RDSON) 5 mω @.6 V 55 mω @.5 V 65 mω @.8 V mω @. V Input voltage range:. V to.6 V.
24 MHz Rail-to-Rail Amplifiers with Shutdown Option AD8646/AD8647/AD8648
24 MHz Rail-to-Rail Amplifiers with Shutdown Option AD8646/AD8647/AD8648 FEATURES Offset voltage: 2.5 mv maximum Single-supply operation: 2.7 V to 5.5 V Low noise: 8 nv/ Hz Wide bandwidth: 24 MHz Slew
TABLE OF CONTENTS Features... Applications... General Description... Pin Configurations... Revision History... 2 Specifications... 3 Electrical Charac
6 V Rail-to-Rail Operational Amplifiers AD86/AD866/AD867 FEATURES Single-supply operation: 4. V to 6 V Input capability beyond the rails Rail-to-rail output swing Continuous output current: 3 ma Peak output
TABLE OF CONTENTS Specifications... 3 Absolute Maximum Ratings... 4 ESD Caution... 4 Pin Configurations and Function Descriptions... 5 Terminology...
FEATURES Wideband switch: 3 db @ 2.5 GHz ADG904: absorptive 4:1 mux/sp4t ADG904-R: reflective 4:1 mux/sp4t High off isolation (37 db @ 1 GHz) Low insertion loss (1.1 db dc to 1 GHz) Single 1.65 V to 2.75
ADG1411/ADG1412/ADG1413
.5 Ω On Resistance, ±5 V/+2 V/±5 V, icmos, Quad SPST Switches ADG4/ADG42/ADG43 FEATURES.5 Ω on resistance.3 Ω on-resistance flatness. Ω on-resistance match between channels Continuous current per channel
General-Purpose CMOS Rail-to-Rail Amplifiers AD8541/AD8542/AD8544
General-Purpose CMOS Rail-to-Rail Amplifiers FEATURES Single-supply operation: 2.7 V to 5.5 V Low supply current: 45 μa/amplifier Wide bandwidth: MHz No phase reversal Low input currents: 4 pa Unity gain
High Accuracy, Ultralow IQ, 1.5 A, anycap Low Dropout Regulator ADP3339
High Accuracy, Ultralow IQ, 1.5 A, anycap Low Dropout Regulator FEATURES High accuracy over line and load: ±.9% @ 25 C, ±1.5% over temperature Ultralow dropout voltage: 23 mv (typ) @ 1.5 A Requires only
ADA485-/ADA485- TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... Specifications... 3 Spe
NC NC NC NC 5 6 7 8 6 NC 4 PD 3 PD FEATURES Ultralow power-down current: 5 na/amplifier maximum Low quiescent current:.4 ma/amplifier High speed 75 MHz, 3 db bandwidth V/μs slew rate 85 ns settling time
Triple, 6-Channel LCD Timing Delay-Locked Loop AD8389
Triple, 6-Channel LCD Timing Delay-Locked Loop PRODUCT FEATURES High speed Up to 85 MHz clock rate Triple (R, G, B) output Matched delay lines Low power dissipation: 40 mw Reference to rising or falling
Improved Second Source to the EL2020 ADEL2020
Improved Second Source to the EL ADEL FEATURES Ideal for Video Applications.% Differential Gain. Differential Phase. db Bandwidth to 5 MHz (G = +) High Speed 9 MHz Bandwidth ( db) 5 V/ s Slew Rate ns Settling
Triple, 6-Channel LCD Timing Delay-Locked Loop AD8389 PRODUCT FEATURES High speed Up to 85 MHz clock rate Triple (R, G, B) output Matched delay lines
Triple, 6-Channel LCD Timing Delay-Locked Loop PRODUCT FEATURES High speed Up to 85 MHz clock rate Triple (R, G, B) output Matched delay lines Low power dissipation: 40 mw Reference to rising or falling
Wideband 4 GHz, 36 db Isolation at 1 GHz, CMOS, 1.65 V to 2.75 V, Dual SPDT ADG936/ADG936-R
Wideband 4 GHz, 36 db Isolation at 1 GHz, CMOS, 1.65 V to 2.75 V, Dual SPDT ADG936/ FEATURES Wideband switch: 3 db @ 4 GHz ADG936 absorptive dual SPDT reflective dual SPDT High off isolation (36 db @ 1
Ultraprecision Operational Amplifier OP177
Ultraprecision Operational Amplifier FEATURES Ultralow offset voltage TA = 25 C, 25 μv maximum Outstanding offset voltage drift 0. μv/ C maximum Excellent open-loop gain and gain linearity 2 V/μV typical
3 V/5 V CMOS 0.5 Ω SPDT/2:1 Mux in SC70 ADG849
3 V/5 V CMOS.5 Ω SPT/2: Mux in SC7 AG849 FEATURES Ultralow on-resistance:.5 Ω typical.8 Ω maximum at 5 V supply Excellent audio performance, ultralow distortion:.3 Ω typical.24 Ω maximum RON flatness High
1.5 Ω On Resistance, ±15 V/12 V/±5 V, icmos, Dual SPDT Switch ADG1436
Data Sheet.5 Ω On Resistance, ±5 V/2 V/±5 V, icmos, Dual SPDT Switch ADG436 FEATURES.5 Ω on resistance.3 Ω on-resistance flatness. Ω on-resistance match between channels Continuous current per channel
OBSOLETE. Simple Sequencers in 6-Lead SC70 ADM1088. Data Sheet
Data Sheet Simple Sequencers in 6-Lead SC7 FEATURES Provide programmable time delays between enable signals Can be cascaded with power modules for multiple supply sequencing Power supply monitoring from.6
1 Ω Typical On Resistance, ±5 V, +12 V, +5 V, and +3.3 V Dual SPDT Switches ADG1636
FEATURES Ω typical on resistance.2 Ω on resistance flatness ±3.3 V to ±8 V dual supply operation 3.3 V to 6 V single supply operation No VL supply required 3 V logic-compatible inputs Rail-to-rail operation
4 GHz to 18 GHz Divide-by-4 Prescaler ADF5001
4 GHz to 18 GHz Divide-by-4 Prescaler ADF5001 FEATURES Divide-by-4 prescaler High frequency operation: 4 GHz to 18 GHz Integrated RF decoupling capacitors Low power consumption Active mode: 30 ma Power-down
1.2 V Ultralow Power High PSRR Voltage Reference ADR280
1.2 V Ultralow Power High PSRR Voltage Reference FEATURES 1.2 V precision output Excellent line regulation: 2 ppm/v typical High power supply ripple rejection: 80 db at 220 Hz Ultralow power supply current:
ADM6823. Low Voltage, Supervisory Circuit with Watchdog and Manual Reset in 5-Lead SOT-23. Data Sheet FUNCTIONAL BLOCK DIAGRAM FEATURES APPLICATIONS
Data Sheet Low Voltage, Supervisory Circuit with Watchdog and Manual Reset in 5-Lead SOT-23 FEATURES Precision low voltage monitoring 9 reset threshold options: 1.58 V to 4.63 V (typical) 140 ms (minimum)
380 MHz, 25 ma, Triple 2:1 Multiplexers AD8183/AD8185
a FEATURES Fully Buffered Inputs and Outputs Fast Channel-to-Channel Switching: 5 ns High Speed 38 MHz Bandwidth ( 3 db) 2 mv p-p 3 MHz Bandwidth ( 3 db) 2 V p-p V/ s Slew Rate G = +, 2 V Step 5 V/ s Slew
1.8 V Low Power CMOS Rail-to-Rail Input/Output Operational Amplifier AD8515
Data Sheet FEATURES Single-supply operation: 1.8 V to 5 V Offset voltage: 6 mv maximum Space-saving SOT-23 and SC7 packages Slew rate: 2.7 V/μs Bandwidth: 5 MHz Rail-to-rail input and output swing Low
Low Cost, Precision JFET Input Operational Amplifiers ADA4000-1/ADA4000-2/ADA4000-4
Low Cost, Precision JFET Input Operational Amplifiers ADA-/ADA-/ADA- FEATURES High slew rate: V/μs Fast settling time Low offset voltage:.7 mv maximum Bias current: pa maximum ± V to ±8 V operation Low
0.35 Ω CMOS 1.65 V to 3.6 V Single SPDT Switch/2:1 MUX ADG839
.35 Ω CMOS 1.65 V to 3.6 V Single SPT Switch/2:1 MUX AG839 FEATURES 1.65 V to 3.6 V operation Ultralow on resistance:.35 Ω typical.5 Ω max at 2.7 V supply Excellent audio performance, ultralow distortion:.55
1.2 V Precision Low Noise Shunt Voltage Reference ADR512
1.2 V Precision Low Noise Shunt Voltage Reference FEATURES Precision 1.200 V Voltage Reference Ultracompact 3 mm 3 mm SOT-23 Package No External Capacitor Required Low Output Noise: 4 V p-p (0.1 Hz to
4 GHz to 18 GHz Divide-by-8 Prescaler ADF5002
4 GHz to 18 GHz Divide-by-8 Prescaler ADF5002 FEATURES Divide-by-8 prescaler High frequency operation: 4 GHz to 18 GHz Integrated RF decoupling capacitors Low power consumption Active mode: 30 ma Power-down
High Accuracy, Ultralow IQ, 1 A, anycap Low Dropout Regulator ADP3338
High Accuracy, Ultralow IQ, 1 A, anycap Low Dropout Regulator FEATURES High accuracy over line and load: ±.8% @ 25 C, ±1.4% over temperature Ultralow dropout voltage: 19 mv (typ) @ 1 A Requires only CO
0.4 Ω CMOS, Dual DPDT Switch in WLCSP/LFCSP/TSSOP ADG888
FEATURES.8 V to 5.5 V operation Ultralow on resistance.4 Ω typical.6 Ω maximum at 5 V supply Excellent audio performance, ultralow distortion.7 Ω typical.4 Ω maximum RON flatness High current carrying
High Isolation, Silicon SPDT, Nonreflective Switch, 0.1 GHz to 6.0 GHz HMC8038W
5 6 7 8 6 5 4 3 FEATURES Nonreflective, 50 Ω design High isolation: 60 db typical Low insertion loss: 0.8 db typical High power handling 34 dbm through path 29 dbm terminated path High linearity P0.dB:
1 pc Charge Injection, 100 pa Leakage, CMOS, ±5 V/+5 V/+3 V Dual SPDT Switch ADG636
pc Charge Injection, pa Leakage, CMOS, ±5 V/+5 V/+3 V Dual SPDT Switch ADG636 FEATURES pc charge injection ±2.7 V to ±5.5 V dual supply +2.7 V to +5.5 V single supply Automotive temperature range: 4 C
Dual, 3 V, CMOS, LVDS High Speed Differential Driver ADN4663
Dual, 3 V, CMOS, LVDS High Speed Differential Driver ADN4663 FEATURES ±15 kv ESD protection on output pins 600 Mbps (300 MHz) switching rates Flow-through pinout simplifies PCB layout 300 ps typical differential
Microprocessor Supervisory Circuit ADM1232
Microprocessor Supervisory Circuit FEATURES Pin-compatible with MAX1232 and Dallas DS1232 Adjustable precision voltage monitor with 4.5 V and 4.75 V options Adjustable strobe monitor with 150 ms, 600 ms,
Ultralow Power Voltage Comparator with Reference ADCMP380
Data Sheet Ultralow Power Voltage Comparator with Reference FEATURES Comparator with on-chip reference Ultralow power consumption with ICC = 92 na (typical) Precision low voltage monitoring down to.5 V
1.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA4051-2
.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA45-2 FEATURES Very low supply current: 3 μa Low offset voltage: 5 μv maximum Offset voltage drift: 2 nv/ C Single-supply operation:.8 V
Dual Low Offset, Low Power Operational Amplifier OP200
Dual Low Offset, Low Power Operational Amplifier OP200 FEATURES Low input offset voltage: 75 μv maximum Low offset voltage drift, over 55 C < TA < +25 C 0.5 μv/ C maximum Low supply current (per amplifier):
ADG918/ADG919. Wideband 4 GHz, 43 db Isolation at 1 GHz, CMOS 1.65 V to 2.75 V, 2:1 Mux/SPDT Switches
Wideband 4 GHz, 43 db Isolation at 1 GHz, CMOS 1.65 V to 2.75 V, 2:1 Mux/SPDT Switches ADG918/ FEATURES Wideband switch: 3 db @ 4 GHz Absorptive/reflective switches High off isolation (43 db @ 1 GHz) Low
Low Capacitance, Low Charge Injection, ±15 V/12 V icmos, Dual SPDT Switch ADG1236
ata Sheet Low Capacitance, Low Charge Injection, ±5 V/2 V icmos, ual SPT Switch FEATURES.3 pf off capacitance 3.5 pf on capacitance pc charge injection 33 V supply range 2 Ω on resistance Fully specified
Low Capacitance, 16- and 8-Channel ±15 V/+12 V icmos Multiplexers ADG1206/ADG1207
Low Capacitance, 16- and 8-Channel ±15 V/+12 V icmos Multiplexers AG126/AG127 FEATURES
Low Voltage, 400 MHz, Quad 2:1 Mux with 3 ns Switching Time ADG774A
Data Sheet FEATURES Bandwidth: >4 MHz Low insertion loss and on resistance: 2.2 Ω typical On resistance flatness:.3 Ω typical Single 3 V/5 V supply operation Very low distortion:
Quad SPDT Switch ADG333A
Quad SPT Switch AG333A FEATURES 44 V supply maximum ratings VSS to V analog signal range Low on resistance (45 Ω max) Low RON (5 Ω max) Low RON match (4 Ω max) Low power dissipation Fast switching times
1.8 V to 5 V Auto-Zero, In-Amp with Shutdown AD8553
.8 V to 5 V Auto-Zero, In-Amp with Shutdown FEATURES Low offset voltage: 20 μv max Low input offset drift: 0. μv/ C max High CMR: 20 db min @ G = 00 Low noise: 0.7 μv p-p from 0.0 Hz to 0 Hz Wide gain
100 MHz to 4000 MHz RF/IF Digitally Controlled VGA ADL5240
1 MHz to 4 MHz RF/IF Digitally Controlled VGA ADL524 FEATURES Operating frequency from 1 MHz to 4 MHz Digitally controlled VGA with serial and parallel interfaces 6-bit,.5 db digital step attenuator 31.5
0.5 Ω CMOS, 1.8 V to 5.5 V, Dual SPDT/2:1 Mux, Mini LFCSP ADG854
.5 Ω CMOS, 1.8 V to 5.5 V, Dual SPDT/2:1 Mux, Mini LFCSP ADG854 FEATURES.8 Ω typical on resistance Less than 1 Ω maximum on resistance at 85 C 1.8 V to 5.5 V single supply High current carrying capability:
1.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA4051-1/ADA4051-2
.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA-/ADA-2 FEATURES Very low supply current: 3 μa typical Low offset voltage: μv maximum Offset voltage drift: 2 nv/ C Single-supply operation:.8
Single-Supply 42 V System Difference Amplifier AD8205
Single-Supply 42 V System Difference Amplifier FEATURES Ideal for current shunt applications High common-mode voltage range 2 V to +65 V operating 5 V to +68 V survival Gain = 50 Wide operating temperature
Ultraprecision, 36 V, 2.8 nv/ Hz Dual Rail-to-Rail Output Op Amp AD8676
Ultraprecision, 36 V, 2. nv/ Hz Dual Rail-to-Rail Output Op Amp AD676 FEATURES Very low voltage noise: 2. nv/ Hz @ khz Rail-to-rail output swing Low input bias current: 2 na maximum Very low offset voltage:
CMOS Switched-Capacitor Voltage Converters ADM660/ADM8660
CMOS Switched-Capacitor Voltage Converters ADM66/ADM866 FEATURES ADM66: Inverts or Doubles Input Supply Voltage ADM866: Inverts Input Supply Voltage ma Output Current Shutdown Function (ADM866) 2.2 F or
Supervisory Circuits with Watchdog and Manual Reset in 5-Lead SC70 and SOT-23 ADM823/ADM824/ADM825
Data Sheet Supervisory Circuits with Watchdog and Manual Reset in 5-Lead SC70 and SOT-23 ADM823/ADM824/ADM825 FEATURES FUNCTIONAL BLOCK DIAGRAM Precision 2.5 V to 5 V power supply monitor 7 reset threshold
Zero Drift, Unidirectional Current Shunt Monitor AD8219
Zero Drift, Unidirectional Current Shunt Monitor FEATURES High common-mode voltage range 4 V to 8 V operating.3 V to +85 V survival Buffered output voltage Gain = 6 V/V Wide operating temperature range:
LC 2 MOS 5 Ω RON SPST Switches ADG451/ADG452/ADG453
LC 2 MOS 5 Ω RON SPST Switches ADG45/ADG452/ADG453 FEATURES Low on resistance (4 Ω) On resistance flatness (0.2 Ω) 44 V supply maximum ratings ±5 V analog signal range Fully specified at ±5 V, 2 V, ±5
1 Ω Typical On Resistance, ±5 V, +12 V, +5 V, and +3.3 V, 4:1 Multiplexer ADG1604
ata Sheet FEATURES 1 Ω typical on resistance.2 Ω on resistance flatness ±3.3 V to ±8 V dual-supply operation 3.3 V to 16 V single-supply operation No VL supply required 3 V logic-compatible inputs Rail-to-rail
1.8 V to 5 V Auto-Zero, In-Amp with Shutdown AD8563
FEATURES Low offset voltage: μv max Low input offset drift: 0. μv/ C max High CMR: 0 db min @ G = 00 Low noise: 0. μv p-p from 0.0 Hz to 0 Hz Wide gain range: to 0,000 Single-supply operation:. V to. V
High Speed, 3.3 V/5 V Quad 2:1 Mux/Demux (4-Bit, 1 of 2) Bus Switch ADG3257
High Speed, 3.3 V/5 V Quad 2:1 Mux/Demux (4-Bit, 1 of 2) Bus Switch ADG3257 FEATURES 100 ps propagation delay through the switch 2 Ω switches connect inputs to outputs Data rates up to 933 Mbps Single
16 V, 1 MHz, CMOS Rail-to-Rail Input/Output Operational Amplifier ADA4665-2
6 V, MHz, CMOS Rail-to-Rail Input/Output Operational Amplifier ADA4665-2 FEATURES Lower power at high voltage: 29 μa per amplifier typical Low input bias current: pa maximum Wide bandwidth:.2 MHz typical
0.5 Ω CMOS 1.65 V to 3.6 V Dual SPDT/2:1 MUX ADG836L
.5 Ω CMOS 1.65 V to 3.6 V ual SPT/2:1 MUX AG836L FEATURES.5 Ω typical on resistance.8 Ω maximum on resistance at 125 C 1.65 V to 3.6 V operation Automotive temperature range: 4 C to +125 C Guaranteed leakage
Precision, Very Low Noise, Low Input Bias Current Operational Amplifiers
Data Sheet Precision, Very Low Noise, Low Input Bias Current Operational Amplifiers AD8671/AD8672/AD8674 FEATURES Very low noise: 2.8 nv/ Hz, 77 nv p-p Wide bandwidth: 1 MHz Low input bias current: 12
ADCMP608. Rail-to-Rail, Fast, Low Power 2.5 V to 5.5 V, Single-Supply TTL/CMOS Comparator. Data Sheet FEATURES FUNCTIONAL BLOCK DIAGRAM APPLICATIONS
Data Sheet Rail-to-Rail, Fast, Low Power 2.5 V to 5.5 V, Single-Supply TTL/CMOS Comparator FEATURES Fully specified rail to rail at VCC = 2.5 V to 5.5 V Input common-mode voltage from 0.2 V to VCC + 0.2
Octal, 16-Bit DAC with 5 ppm/ C On-Chip Reference in 14-Lead TSSOP AD5668-EP
Data Sheet Octal, -Bit with 5 ppm/ C On-Chip Reference in -Lead TSSOP FEATURES Enhanced product features Supports defense and aerospace applications (AQEC) Military temperature range ( 55 C to +5 C) Controlled
Ultralow Offset Voltage Operational Amplifier OP07
Ultralow Offset Voltage Operational Amplifier OP07 FEATURES Low VOS: 75 μv maximum Low VOS drift:.3 μv/ C maximum Ultrastable vs. time:.5 μv per month maximum Low noise: 0.6 μv p-p maximum Wide input voltage
4 MHz, 7 nv/ Hz, Low Offset and Drift, High Precision Amplifier ADA EP
Enhanced Product FEATURES Low offset voltage and low offset voltage drift Maximum offset voltage: 9 µv at TA = 2 C Maximum offset voltage drift:.2 µv/ C Moisture sensitivity level (MSL) rated Low input
+5 V Powered RS-232/RS-422 Transceiver AD7306
a FEATURES RS-3 and RS- on One Chip Single + V Supply. F Capacitors Short Circuit Protection Excellent Noise Immunity Low Power BiCMOS Technology High Speed, Low Skew RS- Operation C to + C Operations
20 MHz to 500 MHz IF Gain Block ADL5531
20 MHz to 500 MHz IF Gain Block ADL5531 FEATURES Fixed gain of 20 db Operation up to 500 MHz Input/output internally matched to 50 Ω Integrated bias control circuit Output IP3 41 dbm at 70 MHz 39 dbm at
Dual/Quad Low Power, High Speed JFET Operational Amplifiers OP282/OP482
Dual/Quad Low Power, High Speed JFET Operational Amplifiers OP282/OP482 FEATURES High slew rate: 9 V/μs Wide bandwidth: 4 MHz Low supply current: 2 μa/amplifier maximum Low offset voltage: 3 mv maximum
20 MHz to 6 GHz RF/IF Gain Block ADL5542
FEATURES Fixed gain of db Operation up to 6 GHz Input/output internally matched to Ω Integrated bias control circuit Output IP3 46 dbm at MHz 4 dbm at 9 MHz Output 1 db compression:.6 db at 9 MHz Noise
Ultrafast Comparators AD96685/AD96687
a FEATURES Fast: 2.5 ns Propagation Delay Low Power: 118 mw per Comparator Packages: DIP, SOIC, PLCC Power Supplies: +5 V, 5.2 V Logic Compatibility: ECL 50 ps Delay Dispersion APPLICATIONS High Speed