NC7WZ17 TinyLogic UHS Dual Buffer with Schmitt Trigger Inputs
|
|
|
- Jody McKinney
- 5 years ago
- Views:
Transcription
1 January 2012 NC7WZ17 TinyLogic UHS Dual Buffer with Schmitt Trigger Inputs Features Ultra-High Speed: t PD 3.6ns (Typical) into 50pF at 5 CC High Output Drive: ±24m at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of LCX when Operated at 3.3 CC Power Down High Impedance Inputs/Outputs Over-oltage Tolerance Inputs Facilitate 5 to 3 Translation Proprietary Noise/EMI Reduction Circuitry Ultra-Small MicroPak Packages Space-Saving SC70 Package Description The NC7WZ17 is a dual buffer with Schmitt trigger inputs from Fairchild's Ultra-High Speed (UHS) series of TinyLogic products. The device is fabricated with advanced CMOS technology to achieve ultra-high speed with high output drive, while maintaining low static power dissipation over a very broad CC operating range. The device is specified to operate over the 1.65 to 5.5 CC range. The inputs and outputs are high-impedance when CC is 0. Inputs tolerate voltages up to 7, independent of CC operating voltage. Schmitt trigger inputs achieve 1 typical hysteresis between the positive- and negativegoing input threshold voltage at 5. Ordering Information Part Number Operating Temperature Top Mark Package NC7WZ17P -40 to +85 C Z17 6-Lead SC70, EIJ SC-88a, 1.25mm Wide NC7WZ17L -40 to +85 C 5 6-Lead MicroPak, 1.00mm Wide NC7WZ17FHX -40 to +85 C 5 6-Lead, MicroPak2, 1x1mm Body,.35mm Pitch Packing Method 3000 Units on Tape & Reel 5000 Units on Tape & Reel 5000 Units on Tape & Reel NC7WZ17 Rev
2 Connection Diagrams Pin Configurations 1 GND Y1 IEEC/IEC 1 1 Y 1 2 Y 2 CC Y2 Figure 2. SC70 (Top iew) Figure 1. Logic Symbol Pin One 1 GND Y 1 CC Y 2 Figure 3. MicroPak (Top Through iew) Notes: 1. represents Product Code Top Mark (see ordering code). 2. Orientation of Top Mark determines Pin One location. Read the top product code mark left to right. Pin One is the lower left pin. Figure 4. SC70 Pin 1 Orientation Pin Definitions Pin # SC70 Pin # MicroPak Name Description Input 2 2 GND Ground Input 4 4 Y 2 Output 5 5 CC Supply oltage 6 6 Y 1 Output Function Table Y = H = HIGH Logic Level L = LOW Logic Level Inputs L H Output Y L H NC7WZ17 Rev
3 bsolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit CC Supply oltage IN DC Input oltage OUT DC Output oltage I IK DC Input Diode Current IN < m I OK DC Output Diode Current OUT < m I OUT DC Output Current ±50 m I CC or I GND DC CC or Ground Current ±100 m T STG Storage Temperature Range C T J Junction Temperature Under Bias +150 C T L Junction Lead Temperature (Soldering, 10 Seconds) +260 C P D Power Dissipation at 85 C ESD SC MicroPak MicroPak Human Body Model, JEDEC:JESD Charge Device Model, JEDEC:JESD22-C Recommended Operating Conditions (3) The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to bsolute Maximum Ratings. mw Symbol Parameter Conditions Min. Max. Unit CC Supply oltage Operating Supply oltage Data Retention IN Input oltage OUT Output oltage 0 CC T Operating Temperature C SC J Thermal Resistance MicroPak MicroPak Note: 3. Unused inputs must be held HIGH or LOW. They may not float. C/W NC7WZ17 Rev
4 DC Electrical Characteristics T =25 C T =-40 to 85 C Symbol Parameter CC () Conditions Min. Typ. Max. Min. Max P Positive Threshold oltage N Negative Threshold oltage H Hysteresis oltage IN = IH, I OH =-100µ OH OL HIGH Level Output oltage LOW Level Output oltage I OH =-4m I OH =-8m I OH =-16m I OH =-24m I OH =-32m IN = IL, I OL =100µ I OL =4m I OL =8m I OL =16m I OL =24m I OL =32m I IN Input Leakage Current 0 to 5.5 IN =5.5, GND ±0.1 ±1.0 µ I OFF Power Off Leakage Current Units 0 IN or OUT = µ I CC Quiescent Supply Current 1.65 to 5.50 IN =5.5, GND 1 10 µ NC7WZ17 Rev
5 C Electrical Characteristics Symbol Parameter CC () Conditions T =25 C Min. Typ. Max. Min. Max. T =-40 to 85 C Units Figure ± 0.20 C L =15pF, Figure R L =1M Figure 6 t PLH, t PHL Propagation Delay 3.30 ± ns 5.00 ± ± 0.30 C L =50pF, Figure ± 0.50 R L = Figure 6 C IN Input Capacitance pf C PD Power Dissipation Capacitance (4) pf Figure 7 Note: 4. C PD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (I CCD ) at no output loading and operating at 50% duty cycle. C PD is related to I CCD dynamic operating current by the expression: I CCD =(C PD )( CC )(f IN )+(I CCstatic ). Input CC C L R L Note: 5. C L includes load and stray capacitance; Input PRR=1.0MHz; t W =500ns Output Input Output CC GND t r = 3ns OH 90% 90% 50% 50% 10% 10% t W t PLH t PHL 50% 50% t f = 3ns OL Figure 5. C Test Circuit Figure 6. C Waveforms CC Input Note: 6. Input=C Waveform; t r =t f =1.8ns; PRR=10MHz; Duty Cycle =50%. Figure 7. I CCD Test Circuit NC7WZ17 Rev
6 Physical Dimensions PIN ONE (0.25) GGE PLNE C ± SETING PLNE B 1.25± B (R0.10) 0.10 C SYMM CL 1.30 SEE 2.10± MIN 0.40 MIN LND PTTERN RECOMMENDTION NOTES: UNLESS OTHERWISE SPECIFIED ) THIS PCKGE CONFORMS TO EIJ SC-88, B) LL DIMENSIONS RE IN MILLIMETERS. C) DIMENSIONS DO NOT INCLUDE BURRS OR MOLD FLSH. D) DRWING FILENME: MKT-M06RE SCLE: 60X Figure 8. 6-Lead, SC70, EIJ SC-88a, 1.25mm Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. lways visit Fairchild Semiconductor s online packaging area for the most recent package drawings: Tape and Reel Specification Please visit Fairchild Semiconductor s online packaging area for the most recent tape and reel specifications: Package Designator Tape Section Cavity Number Cavity Status Cover Type Status P Leader (Start End) 125 (Typical) Empty Sealed Carrier 3000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed NC7WZ17 Rev
7 Physical Dimensions 2X PIN 1 IDENTIFIER 5 (0.05) 0.55MX C 1.45 (0.254) TOP IEW BOTTOM IEW B 2X Notes: 1. CONFORMS TO JEDEC STNDRD M0-252 RITION UD 2. DIMENSIONS RE IN MILLIMETERS 3. DRWING CONFORMS TO SME Y14.5M FILENME ND REISION: MC06RE4 5. PIN ONE IDENTIFIER IS 2X LENGTH OF NY OTHER LINE IN THE MRK CODE LYOUT (0.49) 5X (0.52) 1X PIN C B 5X 5X (0.13) 4X X 45 CHMFER Figure 9. 6-Lead, MicroPak, 1.0mm Wide (1) (0.30) RECOMMENED LND PTTERN (0.75) 0.45 PIN 1 TERMINL Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. lways visit Fairchild Semiconductor s online packaging area for the most recent package drawings: Tape and Reel Specification Please visit Fairchild Semiconductor s online packaging area for the most recent tape and reel specifications: Package Designator Tape Section Cavity Number Cavity Status Cover Type Status L Leader (Start End) 125 (Typical) Empty Sealed Carrier 5000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed NC7WZ17 Rev
8 Physical Dimensions 2X 5X 0.25 PIN 1 MIN 250uM C (0.08) 4X 1.00 TOP IEW SIDE IEW B 0.55MX (0.08) 4X BOTTOM IEW NOTES:. COMPLIES TO JEDEC MO-252 STNDRD B. DIMENSIONS RE IN MILLIMETERS. C. DIMENSIONS ND TOLERNCES PER SME Y14.5M, 1994 D. LNDPTTERN RECOMMENDTION IS BSED ON FSC DESIGN. E. DRWING FILENME ND REISION: MGF06RE3 2X 0.10 C B.05 C 5X X X X X45 CHMFER (0.05) RECOMMENDED LND PTTERN FOR SPCE CONSTRINED PCB LTERNTIE LND PTTERN FOR UNIERSL PPLICTION PIN 1 LED SCLE: 2X Figure Lead, MicroPak2, 1x1mm Body,.35mm Pitch Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. lways visit Fairchild Semiconductor s online packaging area for the most recent package drawings: Tape and Reel Specification Please visit Fairchild Semiconductor s online packaging area for the most recent tape and reel specifications: Package Designator Tape Section Cavity Number Cavity Status Cover Type Status FHX Leader (Start End) 125 (Typical) Empty Sealed Carrier 5000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed NC7WZ17 Rev
9 NC7WZ17 Rev
NC7WZ16 TinyLogic UHS Dual Buffer
NC7WZ16 TinyLogic UHS Dual Buffer Features Ultra-High Speed: t PD 2.4ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of LCX when
NC7WZ07 TinyLogic UHS Dual Buffer (Open-Drain Outputs)
April 2013 NC7WZ07 TinyLogic UHS Dual Buffer (Open-Drain Outputs) Features Ultra-High Speed: t PZL 2.3 ns (Typical) High I OL Output Drive: ±24 ma at 3 CC Broad CC Operating Range: 1.65 to 5.50 Power Down
NC7SZ14 TinyLogic UHS Inverter with Schmitt Trigger Input
January 2010 NC7SZ14 TinyLogic UHS Inverter with Schmitt Trigger Input Features Ultra-High Speed: t PD 3.7ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65
NC7SZ157 TinyLogic UHS 2-Input Non-Inverting Multiplexer
NC7SZ157 TinyLogic UHS 2-Input Non-Inverting Multiplexer Features Broad CC Operating Range: 1.65 to 5.5 Ultra High-Speed Power Down High-Impedance Inputs/Outputs Over-oltage Tolerance Inputs Facilitate
NC7SZ57 / NC7SZ58 TinyLogic UHS Universal Configurable Two-Input Logic Gates
NC7SZ57 / NC7SZ58 TinyLogic UHS Universal Configurable Two-Input Logic Gates Features Ultra High Speed Capable of Implementing any Two-Input Logic Functions Typical Usage Replaces Two (2) TinyLogic Gate
NC7SZ86 TinyLogic UHS Two-Input Exclusive-OR Gate
NC7SZ86 TinyLogic UHS Two-Input Exclusive-OR Gate Features Ultra-High Speed: t PD 2.9ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance
NC7SZ08 TinyLogic UHS Two-Input AND Gate
NC7SZ08 TinyLogic UHS Two-Input AND Gate Features Ultra-High Speed: t PD 2.7ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of
NC7SZ00 TinyLogic UHS Two-Input NAND Gate
NC7SZ00 TinyLogic UHS Two-Input NAND Gate Features Ultra-High Speed: t PD 2.4ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of
NC7SZ125 TinyLogic UHS Buffer with Three-State Output
NC7SZ125 TinyLogic UHS Buffer with Three-State Output January 2014 NC7SZ125 TinyLogic UHS Buffer with Three-State Output Features Ultra-High Speed: t PD 2.6 ns (Typical) into 50 pf at 5 CC High Output
NC7SZ125 TinyLogic UHS Buffer with Three-State Output
NC7SZ125 TinyLogic UHS Buffer with Three-State Output Features Ultra-High Speed: t PD 2.6ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance
NC7SZ125 TinyLogic UHS Buffer with Three-State Output
NC7SZ125 TinyLogic UHS Buffer with Three-State Output Features Ultra-High Speed: t PD 2.6ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance
NC7SZ38 TinyLogic UHS 2-Input NAND Gate, Open Drain Output
NC7SZ38 TinyLogic UHS 2-Input NAND Gate, Open Drain Output Features Ultra-High Speed: t PD 2.4ns (Typical) into 50pF at 5V V CC Open Drain Output Stage for OR Tied Applications High Output Sink Drive:
NC7SZ74 TinyLogic UHS D-Type, Flip-Flop with Preset and Clear
NC7SZ74 TinyLogic UHS D-Type, Flip-Flop with Preset and Clear Features Ultra-High Speed: t PD 2.6 (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Power
NC7SZU04 TinyLogic UHS Unbuffered Inverter
NC7SZU04 TinyLogic UHS Unbuffered Inverter Features Unbuffered for Crystal Oscillator and Analog Applications Balanced Output Drive: ±16mA at 4.5 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance
NC7SV57 / NC7SV58 TinyLogic ULP-A Universal Configurable Two-Input Logic Gates
December 2010 NC7S57 / NC7S58 TinyLogic ULP-A Universal Configurable Two-Input Logic Gates Features 0.9 to 3.6 CC Supply Operation 3.6 Over-oltage Tolerant I/Os at CC from 0.9 to 3.6 Extremely High Speed
NC7SV05 TinyLogic ULP-A Inverter (Open-Drain Output)
NC7SV05 TinyLogic ULP-A Inverter (Open-Drain Output) Features 0.9V to 3.6V V CC Supply Operation 3.6V Over-Voltage Tolerant I/Os at VCC from 0.9V to 3.6V Extremely High Speed tpd - 1.0ns: Typical for 2.7V
Is Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
Description. NC7WZ14FHX -40 to +85 C A9 6-Lead, MicroPak2, 1x1mm Body,.35mm Pitch IEEC/IEC. Figure 1. Logic Symbol
NC7WZ14 TinyLogic UHS Dual Inverter with Schmitt Trigger Inputs Features Ultra-High Speed: t PD 3.2ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5
NC7WZ86 TinyLogic UHS Dual 2-Input Exclusive-OR Gate
TinyLogic UHS Dual 2-Input Exclusive-OR Gate General Description The NC7WZ86 is a dual 2-Input Exclusive-OR Gate from Fairchild s Ultra High Speed Series of TinyLogic. The device is fabricated with advanced
NC7SZ08 TinyLogic UHS 2-Input AND Gate
TinyLogic UHS 2-Input AND Gate General Description The NC7SZ08 is a single 2-Input AND Gate from Fairchild s Ultra High Speed Series of TinyLogic. The device is fabricated with advanced CMOS technology
NC7SZ00 TinyLogic UHS 2-Input NAND Gate
NC7SZ00 TinyLogic UHS 2-Input NAND Gate General Description The NC7SZ00 is a single 2-Input NAND Gate from Fairchild s Ultra High Speed Series of TinyLogic. The device is fabricated with advanced CMOS
NC7WZ04/D. TinyLogic UHS Dual Inverter. NC7WZ04 TinyLogic UHS Dual Inverter. Features. Description. Ordering Information. Connection Diagrams
NC7WZ04 TinyLogic UHS Dual Inverter Features Ultra-High Speed: t PD 2.3ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of LCX w
NC7SZ386 TinyLogic UHS 3-Input Exclusive-OR Gate
TinyLogic UHS 3-Input Exclusive-OR Gate General Description The NC7SZ386 is a single 3-Input Exclusive-OR Gate from Fairchild s Ultra High Speed Series of TinyLogic. The device is fabricated with advanced
NC7SZ32 -TinyLogic UHS Two-Input OR Gate
NC7SZ32 TinyLogic UHS Two-Input OR Gate Features Ultra-High Speed: t PD 2.4ns (Typical) into 50pF at 5V V CC High Output Drive: ±24mA at 3V V CC Broad V CC Operating Range: 1.65V to 5.5V Matches Performance
Description. Part Number Top Mark Package Packing Method
NC7SZ04 TinyLogic UHS Inverter Features Ultra-High Speed: t PD 2.4ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of LCX w hen
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. NC7SZ02 TinyLogic UHS 2-Input NOR Gate General Description The NC7SZ02 is
Is Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
Description. Eco Status. NC7SZ14M5X -40 to +85 C 7Z14 RoHS 5-Lead, SOT23, JEDEC MO-178, 1.6mm
NC7SZ14 TinyLogic UHS Inverter with Schmitt Trigger Input Features Ultra-High Speed: t PD 3.7ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches
NC7WZ125 TinyLogic UHS Dual Buffer with 3-STATE Outputs
March 2001 Revised January 2005 TinyLogic UHS Dual Buffer with 3-STATE Outputs General Description The is a Dual Non-Inverting Buffer with independent active LOW enables for the 3-STATE outputs. The Ultra
NC7SZ175 TinyLogic UHS D-Type Flip-Flop with Asynchronous Clear
TinyLogic UHS D-Type Flip-Flop with Asynchronous Clear General Description The NC7SZ175 is a single positive edge-triggered D-type CMOS Flip-Flop with Asynchronous Clear from Fairchild s Ultra High Speed
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. NC7SZ126 TinyLogic UHS Buffer with 3-STATE Output General Description The
74AUP1G95 TinyLogic Low Power Universal Configurable Two-Input Logic Gate (Open Drain Output)
74UPG9 TinyLogic Low Power Universal onfigurable Two-Input Logic Gate (Open Drain Output) Features 0.8 V to.6 V V Supply Operation.6 V Over-Voltage Tolerant I/Os at V from 0.8V to.6 V Extremely High Speed
NC7WZ132 TinyLogic UHS Dual 2-Input NAND Gate with Schmitt Trigger Inputs
NC7WZ132 TinyLogic UHS Dual 2-Input NAND Gate with Schmitt Trigger Inputs Features Space saving US8 surface mount package MicroPak leadless package Ultra High Speed; t PD 3.1ns typ. into 50pF at 5V V CC
NC7S14 TinyLogic HS Inverter with Schmitt Trigger Input
January 1996 Revised August 2004 NC7S14 TinyLogic HS Inverter with Schmitt Trigger Input General Description The NC7S14 is a single high performance CMOS Inverter with Schmitt Trigger input. The circuit
NC7SZ66 Low Voltage Single SPST Normally Open Bus Switch
September 2013 NC7SZ66 Low Voltage Single SPST Normally Open Bus Switch Features Broad V CC Operating Range: 1.65 V to 5.5 V Rail-to-Rail Signal Handling Power Down High-Impedance Inputs/Outputs 5 Ω Switch
NC7S86 TinyLogic HS 2-Input Exclusive-OR Gate
TinyLogic HS 2-Input Exclusive-OR Gate General Description The is a single 2-Input high performance CMOS Exclusive-OR Gate. Advanced Silicon Gate CMOS fabrication assures high speed and low power circuit
NC7SZ86 TinyLogic UHS Two-Input Exclusive-OR Gate
NC7SZ86 TinyLogic UHS Two-Input Exclusive-OR Gate Features Ultra-High Speed: t PD 2.9ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance
NC7SZ157 TinyLogic UHS 2-Input Non-Inverting Multiplexer
NC7SZ157 TinyLogic UHS 2-Input Non-Inverting Multiplexer Features Broad CC Operating Range: 1.65 to 5.5 Ultra High-Speed Pow er Dow n High-Impedance Inputs/Outputs Over-oltage Tolerance Inputs Facilitate
NC7SZ125 TinyLogic UHS Buffer with Three-State Output
NC7SZ125 TinyLogic UHS Buffer with Three-State Output NC7SZ125 TinyLogic UHS Buffer with Three-State Output Features Ultra-High Speed: t PD 2.6 ns (Typical) into 50 pf at 5 CC High Output Drive: ±24 ma
NC7S04 TinyLogic HS Inverter
NC7S04 TinyLogic HS Inverter General Description The NC7S04 is a single high performance CMOS Inverter. Advanced Silicon Gate CMOS fabrication assures high speed and low power circuit operation over a
NC7SZ32 TinyLogic UHS 2-Input OR Gate
NC7SZ32 TinyLogic UHS 2-Input OR Gate General Description The NC7SZ32 is a single 2-Input OR Gate from Fairchild s Ultra High Speed Series of TinyLogic. The device is fabricated with advanced CMOS technology
NC7SZ157 TinyLogic UHS 2-Input Non-Inverting Multiplexer
April 2000 Revised August 2004 NC7SZ157 TinyLogic UHS 2-Input Non-Inverting Multiplexer General Description The NC7SZ157 is a single, high performance, 2 to 1 CMOS non-inverting multiplexer from Fairchild
NC7S08 TinyLogic HS 2-Input AND Gate
TinyLogic HS 2-Input AND Gate General Description The NC7S08 is a single 2-Input high performance CMOS AND Gate. Advanced Silicon Gate CMOS fabrication assures high speed and low power circuit operation
NC7ST00 TinyLogic HST 2-Input NAND Gate
TinyLogic HST 2-Input NAND Gate General Description The is a single 2-Input high performance CMOS NAND Gate, with TTL-compatible inputs. Advanced Silicon Gate CMOS fabrication assures high speed and low
NC7WZ17 TinyLogic UHS Dual Buffer with Schmitt Trigger Inputs
April 2006 NC7WZ17 TinyLogic UHS Dual Buffer with Schmitt Trigger Inputs General Description The NC7WZ17 is a dual buffer with Schmitt trigger inputs from Fairchild s Ultra High Speed Series of TinyLogic
Low-Voltage, 1 Ω Dual SPST Analog Switch with Power-Off Isolation. Description
FS1259 Low-Voltage, 1 Ω Dual SPST nalog Switch with Power-Off Isolation Features Power-Off Isolation (V CC =0 V) 1 Ω On Resistance (R ON ) for 4.5V V CC 0.25 Ω Maximum R ON Flatness for 4.5 V V CC Space-Saving,
SGM7SZ04 Small Logic Inverter
Preliminary Datasheet SGM7SZ04 GENERL DESCRIPTION The SGM7SZ04 is a single inverter from SGMICRO s Small Logic series. The device is fabricated with advanced CMOS technology to achieve ultra-high speed
NC7SZ175 TinyLogic UHS D-Type Flip-Flop with Asynchronous Clear
NC7SZ175 TinyLogic UHS D-Type Flip-Flop with Asynchronous Clear General Description The NC7SZ175 is a single positive edge-triggered D-type CMOS Flip-Flop with Asynchronous Clear from ON Semiconductor
NC7SZ125 TinyLogic UHS Buffer with 3-STATE Output
NC7SZ125 TinyLogic UHS Buffer with 3-STATE Output Features Space saving SOT23 or SC70 5-lead package Ultra small MicroPak Pb-Free leadless package Ultra High Speed; t PD 2.6ns Typ. into 50pF at 5V V CC
Is Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
Is Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
MM74HC86 Quad 2-Input Exclusive OR Gate
MM74HC86 Quad 2-Input Exclusive OR Gate Features Typical Propagation Delay: 9ns Wide Operating oltage Range: 2 6 Low Input Current: 1mA Maximum Low Quiescent Current: 20mA Max. (74 Series) Output Drive
NC7S14 TinyLogic HS Inverter with Schmitt Trigger Input
NC7S14 TinyLogic HS Inverter with Schmitt Trigger Input General Description The NC7S14 is a single high performance CMOS Inverter with Schmitt Trigger input. The circuit design provides hysteresis between
FSA1259 / FSA1259A Low-Voltage, 1Ω Dual SPST Analog Switch with Power-Off Isolation
FS1259 / FS1259 Low-Voltage, 1Ω Dual SPST nalog Switch with Power-Off Isolation Features Power-Off Isolation (=0V) 1Ω On Resistance (R ON) for 4.5V 0.25Ω Maximum R ON Flatness for 4.5V Space-Saving, US8
FSA Ω Low-Voltage SPDT Analog Switch
F5157 0.4Ω Low-Voltage PDT nalog witch Features Typical 0.4Ω On Resistance (R ON ) for +2.7V upply F5157 Features Less than 12μ I CCT Current When Input is Lower than 0.25Ω Maximum R ON Flatness for +2.7V
NC7S00 TinyLogic HS 2-Input NAND Gate
NC7S00 TinyLogic HS 2-Input NAND Gate General Description The NC7S00 is a single 2-Input high performance CMOS NAND Gate. Advanced Silicon Gate CMOS fabrication assures high speed and low power circuit
NC7SB3257 TinyLogic UHS 2:1 Multiplexer/Demultiplexer Bus Switch
TinyLogic UHS 2:1 Multiplexer/Demultiplexer Bus Switch General Description The NC7SB3257 is a high performance, 2:1 NMOS passgate multiplexer/demultiplexer from Fairchild s Ultra High Speed Series of TinyLogic.
NC7S08 TinyLogic HS 2-Input AND Gate
NC7S08 TinyLogic HS 2-Input AND Gate Features Space saving SOT23 or SC70 5-lead package Ultra small MicroPak Pb-Free leadless package High Speed; t PD 3.5ns typ Low Quiescent Power; I CC < 1µA Balanced
FT3001 Reset Timer with Configurable Delay
FT3001 Reset Timer with Configurable Delay Features Delay Times: 3.0, 3.75, 4.5, 6.0 Seconds 1 µa I CC Current Consumption in Standby Primary and Secondary Input Reset Pins Push-Pull and Open-Drain Output
74AC14, 74ACT14 Hex Inverter with Schmitt Trigger Input
74AC14, 74ACT14 Hex Inverter with Schmitt Trigger Input Features I CC reduced by 50% Outputs source/sink 24mA 74ACT14 has TTL-compatible inputs Ordering Information Order Number General Description Package
FSA4159 Low-Voltage, 1Ω SPDT Analog Switch with Power-Off Isolation
December 2013 FSA4159 Low-Voltage, 1Ω SPDT Analog Switch with Power-Off Isolation Features Low I CC When the S Input is Lower Than V CC Power-Off Isolation (V CC=0 V) 1 Ω On Resistance (R ON) for 4.5 V
NC7SZD384 1-Bit Low Power Bus Switch with Level Shifting
1-Bit Low Power Bus Switch with Level Shifting General Description The NC7SZD384 provides 1-bit of high-speed CMOS TTL-compatible bus switch. The low on resistance of the switch allows inputs to be connected
FAN156 Low Voltage Comparator
FAN156 Low Voltage Comparator Features Low Supply Current: I DD 6μA (Typical) Single Power Supply Operation Wide Common-Mode Input Voltage Range Push-Pull Output Circuit Low Input Bias Current Internal
74LCX125 Low Voltage Quad Buffer with 5V Tolerant Inputs and Outputs
Low Voltage Quad Buffer with 5V Tolerant Inputs and Outputs General Description The LCX125 contains four independent non-inverting buffers with 3-STATE outputs. The inputs tolerate voltages up to 7V allowing
FSA2257 Low R ON Low-Voltage Dual SPDT Bi-Directional Analog Switch
F2257 Low R ON Low-Voltage Dual PDT Bi-Directional nalog witch Features Maximum 1.15Ω On Resistance (R ON ) for 4.5V upply 0.3Ω Maximum R ON Flatness for +5V upply pace-aving MicroPak Packaging Broad Operating
74LCX14 Low Voltage Hex Inverter with 5V Tolerant Schmitt Trigger Inputs
74LCX14 Low Voltage Hex Inverter with 5V Tolerant Schmitt Trigger Inputs Features 5V tolerant inputs 2.3V 3.6V V CC specifications provided 6.5ns t PD max. (V CC = 3.3V), 10µA I CC max. Power down high
FSAT66 Low Voltage Single SPST Normally Open Analog Switch with TTL Compatible Control Input
April 2003 Revised July 2004 FSAT66 Low Voltage Single SPST Normally Open Analog Switch with TTL Compatible Control Input General Description The FSAT66 is a high speed single pole/single throw normally
FST Bit Bus Switch
Features 4Ω Switch Connection between Two Ports Minimal Propagation Delay through the Switch Low I CC Zero Bounce in Flow-through Mode Control Inputs Compatible with TTL Level Description March 2008 Fairchild
Order Number Package Number Eco Status Package Description
FXL4TD245 Low-Voltage Dual-Supply 4-Bit Signal Translator with Configurable Voltage Supplies and Signal Levels and 3-STATE Outputs and Independent Direction Controls Features Bi-directional interface between
FST Bit Bus Switch
Features 4 Ω Switch Connection between Two Ports Minimal Propagation Delay through the Switch Low I CC Zero Bounce in Flow-through Mode Control Inputs Compatible with TTL Level Description December 2012
FST Bit Low Power Bus Switch
2-Bit Low Power Bus Switch General Description The FST3306 is a 2-bit ultra high-speed CMOS FET bus switch with TTL-compatible active LOW control inputs. The low on resistance of the switch allows inputs
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. 74LCX125 Low Voltage Quad Buffer with 5V Tolerant Inputs and Outputs General
74ALVC245 Low Voltage Bidirectional Transceiver with 3.6V Tolerant Inputs and Outputs
74ALVC245 Low Voltage Bidirectional Transceiver with 3.6V Tolerant Inputs and Outputs Features 1.65V to 3.6V V CC supply operation 3.6V tolerant inputs and outputs Power-off high impedance inputs and outputs
74LCX240 Low Voltage Octal Buffer/Line Driver with 5V Tolerant Inputs and Outputs
74LCX240 Low Voltage Octal Buffer/Line Driver with 5V Tolerant Inputs and Outputs Features 5V tolerant inputs and outputs 2.3V 3.6V V CC specifications provided 6.5ns t PD max. (V CC = 3.3V), 10µA I CC
MM74HC132 Quad 2-Input NAND Schmitt Trigger
Quad 2-Input NAND Schmitt Trigger General Description The utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as well as the capability
74LCX04 Low Voltage Hex Inverter with 5V Tolerant Inputs
74LCX04 Low Voltage Hex Inverter with 5V Tolerant Inputs Features 5V tolerant inputs 2.3V 3.6V V CC specifications provided 5.2ns t PD max. (V CC = 3.3V), 10µA I CC max. Power down high impedance inputs
FSA Ω Low-Voltage Dual DPDT Analog Switch
March 2013 FSA2467 0.4Ω Low-Voltage Dual DPDT Analog Switch Features Typical 0.4 On Resistance (R ON ) for +2.7V Supply Features Less then12µa ICCT Current when Sn Input is Lower than V CC 0.25 Maximum
74VHC14 Hex Schmitt Inverter
74VHC14 Hex Schmitt Inverter Features High Speed: t PD = 5.5ns (typ.) at V CC = 5V Low power dissipation: I CC = 2µA (max.) at T A = 25 C High noise immunity: V NIH = V NIL = 28% V CC (min.) Power down
NC7SB3157, FSA3157 Low-Voltage SPDT Analog Switch or 2:1 Multiplexer / De-multiplexer Bus Switch
NC7B3157, F3157 Low-oltage PDT nalog witch or 2:1Multiplexer / De-multiplexer Bus witch Features Useful in Both nalog and Digital pplications pace-aving, C7 6-Lead urface Mount Package Ultra-mall, MicroPak
FSUSB20 Low-Power 1-Port High-Speed USB (480Mbps) Switch
FSUSB20 Low-Power 1-Port High-Speed USB (480Mbps) Switch Features 30dB off isolation at 250MHz 30dB non-adjacent channel crosstalk at 250MHz 4.5Ω typical on resistance (R ON ) 3dB bandwidth: >720MHz Low
74ALVC Low Voltage 16-Bit Bidirectional Transceiver with 3.6V Tolerant Inputs and Outputs and 26Ω Series Resistors in A Port Outputs
74ALVC162245 Low Voltage 16-Bit Bidirectional Transceiver with 3.6V Tolerant Inputs and Outputs and 26Ω Series Resistors in A Port Outputs General Description The ALVC162245 contains sixteen non-inverting
FSAV MHz, 4-Channel, 2:1 Video Switch
Features -50dB Off Isolation at 30MHz -80dB Non-Adjacent Channel Crosstalk at 30MHz 3dB Bandwidth: 800MHz On Resistance: 4 (Typical) Low Power Consumption: 1µA (Maximum) Control Input TTL Compatible Applications
74LCX541 Low Voltage Octal Buffer/Line Driver with 5V Tolerant Inputs and Outputs
74LCX541 Low Voltage Octal Buffer/Line Driver with 5V Tolerant Inputs and Outputs Features 5V tolerant input and outputs 2.3V 3.6V specifications provided 6.5ns t PD max ( = 3.3V), 10µA I CC max Power-down
FSUSB30 Low-Power, Two-Port, High-Speed USB 2.0 (480Mbps) Switch
Click to see this datasheet in Simplified Chinese! FSUSB30 Low-Power, Two-Port, High-Speed USB 2.0 (480Mbps) Switch Features Low On Capacitance: 3.7pF (Typical) Low On Resistance: 6.5Ω (Typical) Low Power
MM74HC132 Quad 2-Input NAND Schmitt Trigger
Quad 2-Input NAND Schmitt Trigger General Description The MM74HC132 utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as well
Is Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
FSAV430 Low Voltage 1.1GHz, 4-Channel, 2:1 Video Switch
FSAV430 Low Voltage 1.1GHz, 4-Channel, 2:1 Video Switch Features -40dB Off Isolation at 30MHz -60dB Non-Adjacent Channel Crosstalk at 30MHz 3dB Bandwidth: 1.1GHz On Resistance: 4.5 (Typical) Low Power
USB1T20 Universal Serial Bus Transceiver
Features Complies with Universal Serial Bus Specification 2.0 for FS/LS Applications Utilizes Digital Inputs and Outputs to Transmit and Receive USB Cable Data Supports 12Mbit/s Full Speed (FS) and 1.5Mbit/s
MM74HC08 Quad 2-Input AND Gate
MM74HC08 Quad 2-Input AND Gate Features Typical propagation delay: 7ns (t PHL ), 12ns (t PLH ) Fanout of 10 LS-TTL loads Quiescent power consumption: 2µA maximum at room temperature Low input current:
M74HC14. Hex Schmitt inverter. Features. Description
Hex Schmitt inverter Features High speed: t PD =12 ns (typ.) at CC = 6 Low power dissipation: I CC = 1 μa (max.) at T A =25 C High noise immunity: H = 1.2 (typ.) at CC = 6 Symmetrical output impedance:
Package Description. Device also available in Tape and Reel except for N14A. Specify by appending suffix letter X to the ordering number.
MM74HC02 Quad 2-Input NOR Gate Features Typical propagation delay: 8ns Wide power supply range: 2V 6V Low quiescent supply current: 20µA maximum (74HC Series) Low input current: 1µA maximum High output
74VHC00 Quad 2-Input NAND Gate
74VHC00 Quad 2-Input NAND Gate Features High Speed: t PD = 3.7ns (typ.) at T A = 25 C High noise immunity: V NIH = V NIL = 28% V CC (min.) Power down protection is provided on all inputs Low noise: V OLP
Is Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
FSUSB22 Low-Power, 2-Port, High-Speed USB 2.0 (480Mbps) Switch
March 2008 FSUSB22 Low-Power, 2-Port, High-Speed USB 2.0 (480Mbps) Switch Features -40dB Off Isolation at 250MHz -40dB Non-adjacent Channel Crosstalk at 250MHz On Resistance: 4.5Ω Typical (RON) -3dB Bandwidth:
M74HCT04. Hex inverter. Features. Description
Hex inverter Features High speed: t PD = 11 ns (typ.) at =4.5V Low power dissipation: I CC = 1 μa (max.) at T A =25 C Compatible with TTL outputs: V IH = 2 V (min.) V IL = 0.8 V (max) Balanced propagation
74VHCT00A Quad 2-Input NAND Gate
74VHCT00A Quad 2-Input NAND Gate Features High speed: t PD = 5.0ns (Typ.) at T A = 25 C High noise immunity: V IH = 2.0V, V IL = 0.8V Power down protection is provided on all inputs and outputs Low noise:
74LVX14 Low Voltage Hex Inverter with Schmitt Trigger Input
74LVX14 Low Voltage Hex Inverter with Schmitt Trigger Input Features Input voltage level translation from 5V to 3V Ideal for low power/low noise 3.3V applications Guaranteed simultaneous switching noise
MM74HCU04 Hex Inverter
MM74HCU04 Hex Inverter General Description The MM74HCU04 inverters utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard
MM74HCT08 Quad 2-Input AND Gate
MM74HCT08 Quad 2-Input AND Gate Features TTL, LS pin-out and threshold compatible Fast switching: t PLH, t PHL = 12ns (typ.) Low power: 10µW at DC High fan-out, 10 LS-TTL loads General Description March
74AC20 Dual 4-Input NAND Gate
74AC20 Dual 4-Input NAND Gate Features I CC reduced by 50% Outputs source/sink 24mA General Description The AC20 contains four, 4-input NAND gates. January 2008 Ordering Information Order Number Package