RX-797 Stereo Receiver

Transcription

1 U RX-797 Stereo Receiver OWNER S MANUAL

2 IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of imptant operating and maintenance (servicing) instructions in the literature accompanying the appliance. Note to CATV system installer: This reminder is provided to call the CATV system installer s attention to Article - of the NEC that provides guidelines f proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. IMPORTANT Please recd the serial number of this unit in the space below. MODEL: Serial No.: The serial number is located on the rear of the unit. Retain this Owner s Manual in a safe place f future reference. Read these instructions. Keep these instructions. 3 Heed all warnings. Follow all instructions. 5 Do not use this apparatus near water. Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accdance with the manufacturer s instructions. Do not install near any heat sources such as radiats, heat registers, stoves, other apparatus (including amplifiers) that produce heat. 9 Do not defeat the safety purpose of the polarized grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade the third prong are provided f your safety. If the provided plug does not fit into your outlet, consult an electrician f replacement of the obsolete outlet. Protect the power cd from being walked on pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessies specified by the manufacturer. Use only with the cart, stand, tripod, bracket, table specified by the manufacturer, sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 3 Unplug this apparatus during lightning stms when unused f long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cd plug is damaged, liquid has been spilled objects have fallen into the apparatus, the apparatus has been exposed to rain moisture, does not operate nmally, has been dropped. We Want You Listening F A Lifetime YAMAHA and the Electronic Industries Association s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring disttion and, most imptantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. i

3 FCC INFORMATION (f US customers) IMPORTANT SAFETY INSTRUCTIONS IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authity, granted by the FCC, to use the product. IMPORTANT: When connecting this product to accessies and/ another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authization to use this product in the USA. 3 NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 5 f Class B digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used accding to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit OFF and ON, please try to eliminate the problem by using one of the following measures: Relocate either this product the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker fuse) circuits install AC line filter/s. In the case of radio TV interference, relocate/reient the antenna. If the antenna lead-in is 3 ohm ribbon lead, change the lead-in to coaxial type cable. If these crective measures do not produce satisfacty results, please contact the local retailer authized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Cp., U.S.A. Orangethpe Ave, Buena Park, CA 9. The above statements apply ONLY to those products distributed by Yamaha Cpation of America its subsidiaries. ii

4 CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest perfmance, please read this manual carefully. Keep it in a safe place f future reference. Install this sound system in a well ventilated, cool, dry, clean place away from direct sunlight, heat sources, vibration, dust, moisture, and/ cold. Allow ventilation space of at least 3 cm on the top, cm on the left and right, and cm on the back of this unit. 3 Locate this unit away from other electrical appliances, mots, transfmers to avoid humming sounds. Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/ personal injury. 5 Avoid installing this unit where feign objects may fall onto this unit and/ this unit may be exposed to liquid dripping splashing. On the top of this unit, do not place: Other components, as they may cause damage and/ discolation on the surface of this unit. Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/ personal injury. Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/ damage to this unit. Do not cover this unit with a newspaper, tablecloth, curtain, etc. in der not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/ personal injury. 7 Do not plug in this unit to a wall outlet until all connections are complete. Do not operate this unit upside-down. It may overheat, possibly causing damage. 9 Do not use fce on switches, knobs and/ cds. When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable. Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/ personal injury. YAMAHA will not be held responsible f any damage resulting from use of this unit with a voltage other than specified. 3 To prevent damage by lightning, keep the power cd and outdo antennas disconnected from a wall outlet the unit during a lightning stm. Do not attempt to modify fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened f any reasons. 5 When not planning to use this unit f long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet. Install this unit near the AC outlet and where the AC power plug can be reached easily. 7 Be sure to read the TROUBLESHOOTING section on common operating errs befe concluding that this unit is faulty. Befe moving this unit, press MASTER ON/OFF to release it outward to the OFF position, and disconnect the AC power plug from the wall outlet. 9 VOLTAGE SELECTOR (Asia and General models only) The VOLTAGE SELECTOR on the rear panel of this unit must be set f your local main voltage BEFORE plugging into the AC main supply. Voltages are: General model...ac ///3 V, 5/ Hz Asia model...ac /3 V, 5/ Hz WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by MASTER ON/OFF, MAIN ZONE ON/OFF and ZONE ON/OFF. In this state, this unit is designed to consume a very small quantity of power. FOR CANADIAN CUSTOMERS To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-3. POUR LES CONSOMMATEURS CANADIENS Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la bne crespondante de la prise et pousser jusqu au fond. Cet appareil numérique de la classe B est confme à la nme NMB-3 du Canada. iii

5 CONTENTS INTRODUCTION FEATURES... SUPPLIED ACCESSORIES... CONTROLS AND FUNCTIONS display... 5 Rear panel Zone remote control... 9 Installing batteries in the remote controls... Using the remote controls... PREPARATION CONNECTIONS... Connecting speakers... Connecting audio and video components... 3 Connecting the AM and FM antennas... Connecting the power supply cd... Turning on and off this unit... 7 BASIC OPERATION PLAYING AND RECORDING... Playing a source... Adjusting the tonal quality... Recding a source... Using the sleep timer... Muting the sound output... 3 FM/AM TUNING... Automatic tuning... Manual tuning... 5 Automatic preset tuning... Manual preset tuning... Selecting preset stations... 9 Exchanging preset stations... 9 SATELLITE RADIO TUNING... 3 What is Satellite Radio?... 3 Satellite Radio connections... 3 Satellite Radio functions... 3 Activating Satellite Radio Basic Satellite Radio operations... 3 Satellite Radio search modes Setting Satellite Radio preset channels ADVANCED OPERATION ADVANCED SETUP...39 Changing the ADVANCED SETUP menu parameters Switching the remote control ID... ZONE... Connecting the Zone components... Controlling Zone... REMOTE CONTROL FEATURES...3 Control area... 3 Controlling other components... Setting remote control codes... 5 ADDITIONAL INFORMATION TROUBLESHOOTING... SPECIFICATIONS...9 INTRODUCTION PREPARATION BASIC OPERATION ADVANCED OPERATION ADDITIONAL INFORMATION

6 FEATURES FEATURES Built-in -channel power amplifier Minimum RMS output power W W ( Ω),.9% THD, Hz to khz Highly dynamic power, low impedance drive capability Sophisticated AM/FM tuner -station random access preset tuning Automatic preset tuning Preset station exchanging capability Radio Data System tuning capability (Europe model only) Satellite Radio (U.S.A. model only) Satellite Radio tuning capability using the Connect-and-Play digital antenna accessy (sold separately) Other features PURE DIRECT button used to reproduce the purest source sound DIRECT AMP button used to reproduce the purest sound REC OUT select independent of input source selection Continuously variable loudness control Sleep timer capability Zone remote control supplied Zone custom installation facility y indicates a tip f your operation. Some operations can be perfmed by using either the buttons on the front panel of this unit those on the remote controls. In case the button names differ between this unit and the remote controls, the names of the buttons on the remote controls are given in parentheses. In case the buttons on the remote control and the Zone remote control have certain functions in common, the illustrations of the buttons on the remote control are used f explanation throughout the manual. This manual is printed pri to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and the product, the product has priity. Please check that you received all of the following parts. SUPPLIED ACCESSORIES Zone remote control Power cable AM loop antenna POWER POWER STANDBY POWER TV AV ZONE POWER STANDBY MD/TAPE 3 MD/TAPE 5 ENT REC CODE SET 7 9 A DISC SKIP B u TV SLEEP PRESET d VOL MUTE CH MUTE 3 A/B/C/D/E MUTE l k h w e f DISPLAY ALL PRESET/CH PRESET CAT. b s a DISC n Indo FM antenna (U.S.A., Canada and General models) Indo FM antenna (Europe and Australia models) 5 7 ID ID p NUMBER 9 ENT. TITLE MENU BAND SRCH MODE ENTER RETURN DISPLAY PRESET/CH Batteries (x) (AA, R, UM-3) Batteries (x) (AAA, R3, UM-)

7 CONTROLS AND FUNCTIONS CONTROLS AND FUNCTIONS A B C D E INTRODUCTION ZONE ON/OFF FM/AM /ANT PURE DIRECT DIRECT AMP ZONE CONTROL EDIT TUN MODE/DISP SEARCH MODE MAN'L/AUTO FM AUTO/MAN'L MASTER A B A/B/C/D/E ON OFF MAIN ZONE PHONES REC OUT MD/TAPE BASS TREBLE BALANCE DISPLAY LOUDNESS FLAT 3dB ON/OFF 3 9 L R 5 7 -db F G H I J K L M N (U.S.A. model) MASTER ON/OFF Press inward to the ON position to turn on the power of this unit. Press again to release it outward to the OFF position to turn off this unit. See page 7 f details. Note Even when this unit is turned off, this unit consumes a small amount of power to preserve the memy. Memy back-up The memy back-up circuit prevents the sted data from being lost. However, the sted data will be lost if the power cd is disconnected from the AC wall outlet f me than one week. MAIN ZONE ON/OFF Turns on Main Zone of this unit sets it to the standby mode. See page 7 f details. Notes This switch is operational only when MASTER ON/OFF is pressed inward to the ON position. In the standby mode, this unit consumes a small amount of power to receive infrared signals from the remote control. 3 A/B Turns on off the speaker set connected to the A and/ B terminals on the rear panel each time the cresponding button is pressed (see page ). ZONE ON/OFF Turns on Zone set it to the standby mode. When Zone is turned on, signals are output at the ZONE OUT jacks. Note This switch is operational only when MASTER ON/OFF is pressed inward to the ON position. 5 ZONE CONTROL Press to control the input source of Zone. Notes This button is operational only when Zone is turned on. When you press this button, the ZONE indicat flashes in the front panel display f approximately 5 seconds. Select the input source of Zone while the indicat is flashing. You can select the preset station channel when is selected as the input source of Zone. sens Receives infrared signals from the remote control. Note Switch the remote control ID between ID and ID when using multiple YAMAHA receivers amplifiers (see pages 9, 39 and ). 7 display Shows infmation about the operational status of this unit. 3

8 CONTROLS AND FUNCTIONS EDIT, SEARCH MODE Exchanges the assignment of two preset stations with each other when is selected as the input source (see page 9). Switches between search modes when is selected as the input source (see page 33). 9 FM/AM, ANT (ANTENNA) Switches the reception band between AM and FM when is selected as the input source (see page ). Shows the reception level of the Connect-and-Play digital antenna (sold separately) when is selected as the input source (see page 3). TUNING/CH l / h Selects the tuning frequency when is selected as the input source (see page ). Searches f a radio channel selects the preset channel number when is selected as the input source (see page 3). A TUN (TUNING) MODE/DISP (DISPLAY) Switches the tuning mode between automatic (the AUTO indicat turns on as a result) and manual (the AUTO indicat turns off as a result) when is selected as the input source. Switches the Satellite Radio infmation shown in the front panel display between channel number/name, categy and artist name/song title when is selected as the input source (see page 3). B Stes a station in the system memy (see page ). Sets this unit to the automatic preset tuning mode (see page ). Stes a radio channel in the system memy when is selected as the input source (see page 37). C PURE DIRECT and indicat Allows you to listen to a source in the purest possible sound. The indicat above it lights up when this function is turned on. See page f details. D DIRECT AMP and indicat Allows you to listen to a source in the purest possible sound. The indicat above it lights up and the front panel display turns off when this function is turned on. See page f details. E Increases decreases the sound output level. Note This does not affect the OUT (REC) level. F select Selects the input source you want to listen to watch. G A/B/C/D/E, Selects the preset station group (A to E) when is selected as the input source (see page 7). Switches between channel categies selects the preset channel group when is selected as the input source (see page 35). H PHONES jack Outputs audio f private listening with your headphones. Note Press SPEAKER A/B so that the SP A/B indicats turn off befe you connect your headphones to the PHONES jack. I REC OUT select Selects a source f recding to the MD recder the tape deck independently of the select setting, allowing you to recd the selected source while listening to another source (see page ). J BASS Increases decreases the low frequency response. The position produces a flat response (see page ). K TREBLE Increases decreases the high frequency response. The position produces a flat response (see page ). L BALANCE Adjusts the sound output balance of the left and right speakers to compensate f sound imbalances caused by speaker locations listening room conditions (see page ). M LOUDNESS Retains a full tonal range at any volume level to compensate f the human ears loss of sensitivity to high and low-frequency ranges at a low volume level (see page ). N Preset station/channel number buttons ( to ) Selects the preset station/channel number ( to ) directly when is selected as the input source (see page 9). Note The Satellite Radio features ( ANT, CH, SEARCH MODE, DISP,, and the preset channel number buttons) are only applicable to the U.S.A. model and are operational only when is selected as the input source. F details, see SATELLITE RADIO TUNING on page 3.

9 CONTROLS AND FUNCTIONS display SP MD/TAPE A B ZONE ZONE3 AUTO TUNED STEREO SLEEP MUTE PTY HOLD EON PS RT PTY CT INTRODUCTION 9 A SP () A/B indicats Light up accding to the set of speakers selected. Both indicats light up when both sets of speakers are selected. ZONE indicat Lights up when Zone is turned on. 3 Input source indicats Light up when this unit is in the cresponding mode. Note The indicat is only applicable to the U.S.A. model. indicat Flashes f approximately 5 seconds after on the front panel is pressed. While the indicat is flashing, ste the displayed station in the system memy by using A/B/C/D/E and one of the preset station number buttons on the front panel. 5 AUTO indicat Lights up when this unit is in the automatic tuning mode. STEREO indicat Lights up when this unit is receiving a strong signal f an FM stereo broadcast while the AUTO indicat is lit. 7 SLEEP indicat Lights up when the sleep timer is turned on. MUTE indicat Flashes while the MUTE function is turned on. 9 Multi-infmation display Shows infmation when adjusting changing settings. TUNED indicat Lights up when this unit is tuned into a station. Europe model only A Radio Data System indicats The box-shaped indicat beside the name of each Radio Data System mode lights up when the cresponding Radio Data System mode is selected. PTY HOLD indicat Lights up while searching f stations in the PTY SEEK mode. EON indicat Lights up when the Radio Data System station that offers the EON data service is being received. 5

10 CONTROLS AND FUNCTIONS Rear panel 3 5 (U.S.A. model) REMOTE AC IN IN GND DTV/ CBL DTV/ CBL OUT AM ANT IN IN IN CONTROL OUT AC OUTLETS SWITCHED 75Ω UNBAL. FM ANT GND OUT MONITOR OUT OUT IN (PLAY) V 5mA MAX. COUPLER MAIN IN CLASS WIRING A IMPEDANCE SELECTOR SET BEFORE POWER ON SELECTEUR D'IMPEDANCE ZONE OUT MD/ TAPE OUT (REC) PRE OUT A OR B: ΩMIN. /SPEAKER AB: ΩMIN. /SPEAKER A OR B: ΩMIN. /SPEAKER VIDEO ZONE OUT SUB WOOFER B AUDIO AUDIO OUTPUT 7 9 A B C D Antenna terminals Connect FM and AM antennas. See page f connections infmation. AUDIO/VIDEO jacks Connect audio and video components. See page 3 f connection infmation. 3 REMOTE jacks These jacks are used to input/output remote control signals. See page f connection infmation. CONTROL OUT jack This is a control expansion jack. Consult your nearest authized YAMAHA dealer service center about this jack. 5 jack (U.S.A. model only) Connect Connect-and-Play digital antenna accessy. See page 3 f connection infmation. AC IN Use to plug in the supplied power cable. See page f connection infmation. 7 jacks Connect a player. See page 3 f connection infmation. jacks and GND terminal Connect a turntable. See page 3 f connection infmation. 9 ZONE jacks Connect a Zone component. See page f connection infmation. SUBWOOFER OUTPUT jack Connect a subwoofer with built-in amplifier. A COUPLER jacks Connect an external unit. See page f connection infmation. B terminals Connect speakers. See page f connection infmation. C IMPEDANCE SELECTOR switch Switches the impedance setting. See page f details. D AC OUTLET(S) (SWITCHED) Use to supply power to your other audio and video components. See page f details. Asia and General models only VOLTAGE SELECTOR See page f details.

11 CONTROLS AND FUNCTIONS This section describes the function of each button on the remote control used to control this unit other components made by YAMAHA other manufacturers. The functions of the buttons used to control your other audio and video components are the same as those of the cresponding buttons on those components. Refer to those components instruction manuals f details. To operate other components using this remote control, see REMOTE CONTROL FEATURES on page POWER Infrared signal transmitter Sends infrared signals. TV STANDBY MD/TAPE REC DISC SKIP VOL MUTE 5 9 TITLE BAND RETURN TV POWER AV CH ENTER PRESET/CH CODE SET MUTE POWER SLEEP MENU Input select buttons Select the desired input source and change the control area (see page 3). 3 7 A B SRCH MODE (U.S.A. model) ENT. DISPLAY 7 9 A B C D E F 3 Numeric buttons Select the preset station number ( to ) when is selected as the input source. Select the preset channel number when is selected as the input source. BAND Switches to the previously used reception band (FM AM) when is selected as the input source. Note The frequency of the previously received station is automatically recalled. 5 () j / i Selects the preset station group (A to E) when is selected as the input source (see page 9). Switches between channel categies selects the preset channel group (A to E) when is selected as the input source (see page 35). PRESET/CH u / d Selects the preset station number ( to ) when is selected as the input source (see page 9). Searches f a radio channel selects the preset channel number ( to ) when is selected as the input source (see page 33). Stes a radio channel in the system memy when is selected as the input source (see page 37). 7 STANDBY Sets this unit to the standby mode. Notes This button is operational only when MASTER ON/OFF on the front panel is pressed inward to the ON position. In the standby mode, this unit consumes a small amount of power to receive infrared signals from the remote control. This button does not set Zone to the standby mode. POWER Turns on this unit. Notes This button is operational only when MASTER ON/OFF on the front panel is pressed inward to the ON position. This button does not turn on Zone. INTRODUCTION 7

12 CONTROLS AND FUNCTIONS 9 A/B Turns on off the set of speakers connected to the A and/ B terminals on the rear panel of this unit when the cresponding button is pressed each time. CODE SET Use to set up remote control codes (see page 5). A SLEEP Sets the sleep timer. B / Increases decreases the sound output level. Notes This does not affect the OUT (REC) level. When you press / to control the sound output level of this unit, on the front panel rotates. C MUTE Mutes the sound output. Press again to reste the sound output to the previous volume level (see page 3). Note The sound output to Zone is not muted. D ENT. (ENTER) Confirms an entered channel number during the Direct Number Access mode when is selected as the input source. E SRCH (SEARCH) MODE Switches between the Satellite Radio search modes (see page 35) when is selected as the input source. F DISPLAY Switches the Satellite Radio infmation shown in the front panel display between channel number/name, categy and artist name/song title when is selected as the input source. Note The Satellite Radio features (, SRCH MODE, DISPLAY, j / i, PRESET/CH u / d, and ENT.) are only applicable to the U.S.A. model and are operational only when is selected as the input source. F details, see SATELLITE RADIO TUNING on page 3.

13 CONTROLS AND FUNCTIONS Zone remote control This section describes the function of each button on the Zone remote control used to control Zone. You can also use the Zone remote control to control the Satellite Radio features and YAMAHA players. 3 5 MD/TAPE 7 u PRESET d A/B/C/D/E ZONE 3 5 POWER STANDBY ENT 9 n p NUMBER MUTE l k h w e f DISPLAY ALL PRESET/CH PRESET CAT. b s a DISC ID ID 7 9 A B C D 3 PRESET u / d Selects the preset station number ( to ) when is selected as the input source. A/B/C/D/E Selects the preset station group (A to E) when is selected as the input source. 5 Satellite Radio control buttons Controls the Satellite Radio features when the / switch is slid to the position. () l / h Switches between channel categies selects the preset channel group (A to E) when is selected as the input source. PRESET/CH k / n Searches f a radio channel selects the preset channel number ( to ) when is selected as the input source. ALL Selects the All Channel Search mode. PRESET Selects the Preset Search mode. CAT. () Selects the Categy Search mode. INTRODUCTION Infrared signal transmitter Sends infrared signals. Input select/numeric buttons Select the desired input source of Zone. Enter a channel number preset channel number when is selected as the input source. Note (U.S.A. model) You must press and hold NUMBER befe you press any of these buttons to enter numbers. ID/ID switch Switches the remote control ID between ID and ID (see page ). 7 POWER Turns on Zone. STANDBY Sets Zone to the standby mode. 9 ENT (ENTER) Confirms an entered channel number during the Direct Number Access mode when is selected as the input source. / Increases decreases the sound output level of Zone. Note This does not affect the OUT (REC) level. 9

14 CONTROLS AND FUNCTIONS A MUTE Mutes the sound output to Zone. Press again to reste the sound output to the previous volume level. B DISPLAY Switches the Satellite Radio infmation displayed in the front panel display between channel number/name, categy and artist name/song title when is selected as the input source. C / switch Switches the function of the control buttons numbered 5, B and D between controlling YAMAHA players and controlling the Satellite Radio features. D NUMBER Press and hold befe you press the input select/numeric buttons to enter numbers to control the Satellite Radio features. Note The Satellite Radio features (, ENT, DISPLAY and the Satellite Radio control buttons) are only applicable to the U.S.A. model and are operational only when is selected as the input source and the / switch is slid to the position. F details, see SATELLITE RADIO TUNING on page 3.

15 MASTER ON OFF MAIN ZONE ON/OFF A B ZONE ON/OFF ZONE CONTROL PHONES BASS FM/AM EDIT SEARCH MODE A/B/C/D/E REC OUT MD/TAPE POWER TV STANDBY MD/TAPE REC DISC SKIP VOL MUTE 5 9 TITLE BAND TV RETURN POWER AV CH ENTER PRESET/CH AUDIO POWER SLEEP 3 7 MUTE ENT. MENU SRCH MODE DISPLAY A B TREBLE BALANCE L R /ANT MAN'L/AUTO FM LOUDNESS FLAT 5 7 TUN MODE/DISP AUTO/MAN'L 3dB 3 9 PURE DIRECT DIRECT AMP CONTROLS AND FUNCTIONS Installing batteries in the remote controls Notes on batteries Change all of the batteries if the operation range of the remote controls decreases. Use AA, R, UM-3 batteries f the remote control and AAA, R3, UM- batteries f the Zone remote control. Make sure that the polarities are crect. See the illustration inside the battery compartment of each remote control. Remove the batteries if the remote controls are not used f an extended period of time. Do not use old batteries together with new ones. Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and col. We strongly recommend using alkaline batteries. If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material letting it come into contact with clothing, etc. Clean the battery compartment thoughly befe installing new batteries. Do not throw away batteries with general house waste; dispose of them crectly in accdance with your local regulations. INTRODUCTION Zone remote control 3 3 Open the battery compartment cover. 3 Close the cover back. Insert the supplied batteries in each remote control accding to the polarity markings ( and ) on the inside of the battery compartment. Using the remote controls The remote controls transmit a directional infrared beam. Be sure to aim the remote controls directly at the remote control sens on the front panel of this unit on the infrared signal receiver in Zone during operation. 3 3 Approximately m (9.7 ft) Handling the remote controls The area between the remote controls and this unit ( the infrared signal receiver in Zone ) must be clear of large obstacles. Do not spill water other liquids on the remote controls. Do not drop the remote controls. Do not leave ste the remote controls in the following types of conditions: places of high humidity, such as near a bath places of high temperature, such as near a heater a stove places of extremely low temperatures dusty places Do not expose the remote control sens to strong lighting, in particular, an inverter type fluescent lamp; otherwise, the remote controls may not wk properly. If necessary, position this unit away from direct lighting.

16 CONNECTIONS CONNECTIONS Connecting speakers Be sure to connect the left channel (L), right channel (R), (red) and (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is increct, the sound will be unnatural and lack bass. CAUTION Befe connecting the speakers, make sure that the power of this unit is turned off. Do not let the bare speaker wires touch each other do not let them touch any metal part of this unit. This could damage this unit and/ the speakers. Use magnetically shielded speakers. If this type of speakers still creates the interference with the monit, place the speakers away from the monit. Remove approximately mm (3/ in) of insulation from the end of each speaker cable and twist the exposed wires of the cable together to eliminate the risk of a sht-circuit. Tighten the knob to secure the wire. Red: positive () Black: negative () mm (3/ in) Unscrew the knob. Red: positive () Black: negative () 3 Insert one bare wire into the hole in the side of each terminal. Notes on the speaker cd A speaker cd is actually a pair of insulated cables running side by side. One cable is coled shaped differently, perhaps with a stripe, groove ridge. Connect the striped, grooved ridged cable to the (red) terminals on this unit and your speaker. Connect the plain cable to the (black) terminals on this unit and your speaker. Connecting the banana plug (U.S.A., Canada, Australia and General models only) First, tighten the knob and then insert the banana plug into the end of the cresponding terminal. Banana plug Red: positive () Black: negative () Notes One two speaker sets can be connected to this unit. If you use only one speaker set, connect it to either the A B terminals. Use speakers with the specified impedance shown on the rear panel of this unit.

17 CONNECTIONS Connecting audio and video components CAUTION Do not connect this unit other components to the main power until all connections between components are complete. All connections must be crect: L (left) to L, R (right) to R, to and to. Also, refer to the owner s manual f each of your components. Use the RCA type pin plug cables f audio and video components except speakers. y The jacks are designed to connect a turntable with an MM high-output MC cartridge. If you have a turntable with a lowoutput MC cartridge, use an in-line boosting transfmer an MC-head amplifier when connecting your turntable to the jacks. Connect your turntable to the GND terminal to reduce noise in the signal. However, you may hear less noise without the connection to the GND terminal f some recd players. Digital TV, Cable TV player, etc. PREPARATION Video monit V Video out R L Audio out V Video out R L Audio out V Video out R L Audio out R L Audio in V Video in V Video in GND DTV/ CBL DTV/ CBL AM ANT IN IN player Audio out 75Ω UNBAL. FM ANT OUT OUT Turntable L R Audio out R GND VIDEO MONITOR OUT ZONE OUT IN (PLAY) MD/ TAPE OUT (REC) ZONE OUT L AUDIO AUDIO GND Audio in R L R L Audio out MD recder, Tape deck, etc. 3

18 CONNECTIONS Connecting the AM and FM antennas Both AM and FM indo antennas are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna crectly to the designated terminals. AM loop antenna (included) Outdo AM antenna Use a 5 to m of vinylcovered wire extended outdos from a window. Indo FM antenna (included) Outdo FM antenna GND AM ANT 75Ω UNBAL. FM ANT GND Ground (GND terminal) F maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. Notes A properly installed outdo antenna provides clearer reception than an indo one. If you experience po reception quality, an outdo antenna may improve the quality. Consult your nearest authized YAMAHA dealer service center about outdo antennas. If you connect an outdo FM antenna to this unit, do not connect the indo FM antenna to this unit. To minimize interference from automobile ignition, locate the antenna as far from heavy traffic as possible. Keep the feeder cable coaxial cable as sht as possible. Do not bundle roll up excess cable. The antenna should be placed at least meters from reinfced concrete walls metal structures.

19 CONNECTIONS Connecting the AM loop antenna Set up the AM loop antenna. 5 Repeat steps to to insert the AM loop antenna lead wires into the GND terminal. Orient the AM loop antenna f the best reception. Press and hold the tab. Notes The AM loop antenna should be placed away from this unit. A properly installed outdo antenna provides clearer reception than an indo one. If you experience po reception quality, an outdo antenna may improve the quality. It is recommended that you should connect a 5 to m of vinyl-covered wire to the AM ANT terminal and extend it outdos from a window. Consult your nearest authized YAMAHA dealer service center about outdo antennas. The AM loop antenna should always be connected, even if an outdo AM antenna is connected to this unit. PREPARATION 3 Insert the AM loop antenna lead wires into the AM ANT terminal. Release the tab. 5

20 CONNECTIONS Connecting the power supply cd Plug the power cable into the AC IN on the rear panel of this unit and then plug the power supply cd into the AC wall outlet after all other connections are complete. VOLTAGE SELECTOR IMPEDANCE SELECTOR SET BEFORE POWER ON SELECTEUR D'IMPEDANCE VOLTAGE SELECTOR Power cable AC IN AC OUTLETS SWITCHED AC OUTLET(S) (SWITCHED) Australia model... outlet Other models... outlets Use these outlets to connect the power supply cds from your other components to this unit. The outlets supply power to any connected components whenever the power of this unit is turned on. F infmation on the maximum power (total power consumption of components), see SPECIFICATIONS on page 9. VOLTAGE SELECTOR (Asia and General models only) VOLTAGE SELECTOR on the rear panel of this unit must be set f your local main voltage BEFORE plugging the power supply cd into the AC wall outlet. Voltages are as follows: Asia model... AC /3 V, 5/ Hz General model... AC ///3 V, 5/ Hz IMPEDANCE SELECTOR switch A OR B: ΩMIN. /SPEAKER AB: ΩMIN. /SPEAKER A OR B: ΩMIN. /SPEAKER CAUTION (General model) IMPEDANCE SELECTOR switch COUPLER jacks Removing the jumper pins from the PRE OUT/MAIN IN jacks enables this unit to operate separately as a control amplifier a power amplifier. These jacks are used to connect a signal-processing system such as a graphic equalizer a surround-sound process to this unit. If such an external unit is connected to these jacks, the control of this unit can be used to adjust the overall sound output level. To connect an external unit, first remove the jumper pins from the PRE OUT/MAIN IN jacks and then connect the input jacks of that external unit to the PRE OUT jacks its output jacks to the MAIN IN jacks. F details, refer to the owner s manual included with the external unit to be connected. Notes AC OUTLET(S) When you do not use the COUPLER jacks, never remove the jumper pins from these jacks. If removed, no sound will be output from this unit. When you use this unit with an external unit connected to the COUPLER jacks, make sure that the DIRECT AMP button and the PURE DIRECT button on the front panel are turned off. When you use this unit as a power amplifier, connect the output jacks of an external control amplifier, etc. to the MAIN IN jacks of this unit. In this case, the controls of this unit will not function except the PHONES jack and the A/B buttons. Use the controls on the external control amplifier to make volume adjustments, etc. Do not slide the IMPEDANCE SELECTOR switch while the power of this unit is turned on, as doing so may damage the unit. Select the switch position (left right) accding to the impedance of the speakers in your system. Switch position Right Left Notes Impedance level If you use one set (A B), the impedance of each speaker must be Ω higher. If you use two sets (A and B), the impedance of each speaker must be Ω higher. If you use one set (A B), the impedance of each speaker must be Ω higher. If you use two sets (A and B), the impedance of each speaker must be Ω higher. The Canada model cannot use two separate speaker sets (A and B) simultaneously when the IMPEDANCE SELECTOR switch is slid to the Ω position. If this unit fails to turn on, the IMPEDANCE SELECTOR switch may not be fully slid to either position. If this is the case, slide the switch all the way to either position when the power supply to this unit is completely cut off.

21 MASTER ON OFF MAIN ZONE ON/OFF A B ZONE ON/OFF ZONE CONTROL PHONES BASS FM/AM /ANT EDIT SEARCH MODE A/B/C/D/E REC OUT MD/TAPE TREBLE BALANCE L R MAN'L/AUTO FM LOUDNESS FLAT 5 7 TUN MODE/DISP AUTO/MAN'L 3dB 3 9 PURE DIRECT -db DIRECT AMP CONNECTIONS Turning on and off this unit When all connections are complete, turn on the power of this unit. Press MASTER ON/OFF on the front panel inward to the ON position to turn on the power of this unit. MASTER ON OFF Main Zone of this unit turns on. You can set Main Zone of this unit to the standby mode by pressing MAIN ZONE ON/OFF on the front panel STANDBY on the remote control. Press MAIN ZONE ON/OFF on the front panel POWER on the remote control to turn Main Zone of this unit on again. Press MASTER ON/OFF on the front panel again to release it outward to the OFF position to turn off this unit. PREPARATION y While MASTER ON/OFF on the front panel is pressed inward to the ON position, you can turn on Zone set it to the standby mode independently (see page ). 7

22 MASTER ON OFF MAIN ZONE ON/OFF A B ZONE ON/OFF ZONE CONTROL PHONES BASS FM/AM /ANT EDIT SEARCH MODE A/B/C/D/E REC OUT MD/TAPE TREBLE BALANCE L R MAN'L/AUTO FM LOUDNESS FLAT 5 7 TUN MODE/DISP AUTO/MAN'L 3dB 3 9 PURE DIRECT -db DIRECT AMP PLAYING AND RECORDING PLAYING AND RECORDING CAUTION Extreme caution should be exercised when you play back s encoded in DTS. If you play back a encoded in DTS on a DTS-incompatible player, you will only hear some unwanted noise that may damage your speakers. Check whether your player suppts s encoded in DTS. Also, check the sound output level of your player befe you play back a encoded in DTS. Playing a source Press A and/ B on the front panel on the remote control to select speakers A and/ speakers B. A B A B 5 POWER TV STANDBY MD/TAPE REC DISC SKIP VOL TV POWER AV CH CODE SET POWER SLEEP A B Notes Both A and B can be selected. Make sure that the IMPEDANCE SELECTOR switch is crectly set (see page ). 3 Play the source. Rotate on the front panel ( press / on the remote control) to adjust the sound output level. Rotate the select on the front panel ( press one of the input select buttons on the remote control) to select the desired input source. -db POWER POWER STANDBY POWER TV AV MD/TAPE

23 PLAYING AND RECORDING 5 Adjust the tonal quality by using the BASS, TREBLE, BALANCE and LOUDNESS controls the DIRECT AMP and the PURE DIRECT buttons on the front panel. BASS TREBLE BALANCE LOUDNESS FLAT 3dB 3 9 L R 5 7 PURE DIRECT DIRECT AMP Press MAIN ZONE ON/OFF on the front panel again ( press STANDBY on the remote control) to finish using this unit and set it to the standby mode. MAIN ZONE ON/OFF STANDBY BASIC OPERATION 9

24 PLAYING AND RECORDING Adjusting the tonal quality Adjusting the BALANCE control Adjusts the sound output balance of the left and right speakers to compensate f sound imbalance caused by speaker locations listening room conditions. BALANCE L R Using the DIRECT AMP button Routes input signals from your player directly to the specially built-in amplifier f the player. As a result, the input signals bypass the select and the BASS, TREBLE, BALANCE and LOUDNESS controls and then sent to the power amplifier, thus eliminating any alterations to the signals and creating the purest possible sound. The DIRECT AMP indicat lights up and the front panel display turns off after a few seconds. Adjusting the LOUDNESS control Retains a full tonal range at any volume level, thus compensating f the human ears loss of sensitivity to high and low-frequency ranges at a low volume level. CAUTION If the DIRECT AMP the PURE DIRECT button is turned on with the LOUDNESS control set at a certain level, the input signals bypass the LOUDNESS control, resulting in a sudden increase in the sound output level. To prevent your ears the speakers from being undesirably damaged, be sure to press the DIRECT AMP the PURE DIRECT button after lowering the sound output level after checking that the LOUDNESS control is properly set. Rotate the LOUDNESS control on the front panel to the FLAT position. LOUDNESS FLAT 3dB DIRECT AMP Using the PURE DIRECT button Routes input signals from your audio sources so that the input signals bypass the BASS, TREBLE, BALANCE and LOUDNESS controls, thus eliminating any alterations to the audio signals and creating the purest possible sound. Rotate on the front panel ( press / on the remote control) to set the sound output level to the loudest listening level that you would listen to. PURE DIRECT -db Note If both the DIRECT AMP and the PURE DIRECT buttons are turned on, only the DIRECT AMP button will function. Adjusting the BASS and TREBLE controls Adjust the high and low frequency response. BASS Increases decreases the low frequency response. TREBLE Increases decreases the high frequency response. 3 Rotate the LOUDNESS control until the desired volume is obtained. LOUDNESS FLAT 3dB BASS TREBLE

25 MASTER ON OFF MAIN ZONE ON/OFF A B ZONE ON/OFF ZONE CONTROL PHONES BASS FM/AM /ANT EDIT SEARCH MODE A/B/C/D/E REC OUT MD/TAPE TREBLE BALANCE L R MAN'L/AUTO FM LOUDNESS FLAT TUN MODE/DISP AUTO/MAN'L 3dB PURE DIRECT -db DIRECT AMP PLAYING AND RECORDING Recding a source Notes The, BASS, TREBLE, BALANCE and LOUDNESS controls and the DIRECT AMP and the PURE DIRECT buttons have no effect on the source being recded. Check the copyright laws in your country to recd from recds, s, radio, etc. Recding copyright-protected material may infringe on copyright laws. Rotate on the front panel ( press / on the remote control) to adjust the sound output level of the selected source to recd from. -db 5 Begin recding on the MD recder, the tape deck the connected to this unit. 3 Rotate the REC OUT select on the front panel to select the source you want to recd from. MD/TAPE REC OUT Note Selecting another source with the select on the front panel ( the cresponding input select button on the remote control) while recding is in progress will not affect the recding. y You can monit the sound and/ picture being recded by rotating the select on the front panel ( pressing MD/ TAPE on the remote control) to select the MD recder, the tape deck the used f recding. BASIC OPERATION Play the selected source to recd from. 3 Rotate the select on the front panel to confirm the selected source to recd from.

26 PLAYING AND RECORDING Using the sleep timer Use this feature to automatically set this unit to the standby mode after a certain amount of time. The sleep timer is useful when you are going to sleep while this unit is playing recding a source. The sleep timer also automatically turns off any external components connected to the AC OUTLETS. POWER TV STANDBY MD/TAPE REC DISC SKIP VOL TV POWER AV CH CODE SET POWER SLEEP A B 3 Press SLEEP repeatedly so that SLEEP OFF appears in the front panel display. SLEEP After a few seconds, SLEEP OFF disappears from the front panel display, and the SLEEP indicat turns off. y The sleep timer setting can also be canceled by pressing STANDBY on the remote control ( MAIN ZONE ON/OFF MASTER ON/OFF on the front panel) to set this unit to the standby mode. Notes The sleep timer can only be set with the remote control. The sleep timer automatically turns off Zone. However, the power of Zone components are not turned off. Press one of the input select buttons on the remote control to select an input source. POWER POWER STANDBY POWER TV AV MD/TAPE Start playback on the selected input source. 3 Press SLEEP repeatedly to set the amount of time befe this unit is set to the standby mode. Each time you press SLEEP, the front panel display changes as shown below. SLEEP SLEEP min SLEEP 9 min SLEEP OFF SLEEP 3 min SLEEP min The SLEEP indicat flashes while switching the amount of time f the sleep timer. SLEEP

27 PLAYING AND RECORDING Muting the sound output Press MUTE on the remote control to mute the sound output. The MUTE indicat flashes in the front panel display and MUTE ON appears in the front panel display. MUTE MUTE After a few seconds, MUTE ON disappears from the front panel display. Press MUTE on the remote control again to resume the sound output. The MUTE indicat disappears from the front panel display. BASIC OPERATION MUTE 3

28 MASTER ON OFF MAIN ZONE ON/OFF A B ZONE ON/OFF ZONE CONTROL PHONES BASS FM/AM /ANT EDIT SEARCH MODE A/B/C/D/E REC OUT MD/TAPE TREBLE BALANCE L R MAN'L/AUTO FM LOUDNESS FLAT TUN MODE/DISP AUTO/MAN'L 3dB PURE DIRECT -db DIRECT AMP FM/AM TUNING There are tuning methods; automatic and manual. Select either method accding to your preference and the strength of station signals. Automatic tuning Automatic tuning is effective when station signals are strong and there is no interference. FM/AM TUNING Press TUNING/CH l / h once to begin automatic tuning. Press h to tune into a higher frequency. Press l to tune into a lower frequency. 3 Notes When you tune into a station, the frequency of the received station is shown in the front panel display. To search f another station, press TUNING/CH l / h once me. If the tuning search does not stop at the desired station because the station signals are weak, try using the manual tuning method. Rotate the select ( press on the remote control) to select as the input source. Press FM/AM on the front panel to select the reception band (FM AM). FM AM appears in the front panel display. FM/AM /ANT 3 Press TUN MODE on the front panel so that the AUTO indicat lights up in the front panel display. TUN MODE/DISP AUTO/MAN'L AUTO Lights up

29 MASTER ON OFF MAIN ZONE ON/OFF A B ZONE ON/OFF ZONE CONTROL PHONES BASS FM/AM /ANT EDIT SEARCH MODE A/B/C/D/E REC OUT MD/TAPE TREBLE BALANCE L R MAN'L/AUTO FM LOUDNESS FLAT 5 7 TUN MODE/DISP AUTO/MAN'L 3dB 3 9 PURE DIRECT -db DIRECT AMP FM/AM TUNING Manual tuning Manual tuning is effective when station signals are weak. 3 Press TUNING/CH l / h to manually tune into the desired station. Hold down the button to continue tuning search. Notes When you tune into a station, the frequency of the received station is shown in the front panel display. If you tune into an FM station, it is automatically received in the monaural mode to increase signal quality. Rotate the select ( press on the remote control) to select as the input source. BASIC OPERATION Press FM/AM on the front panel to select the reception band (FM AM). FM AM appears in the front panel display. FM/AM /ANT 3 Press TUN MODE on the front panel so that the AUTO indicat disappears from the front panel display. TUN MODE/DISP AUTO/MAN'L AUTO Disappears 5