Press Cursors and use the appropriate X and Y functions to measure period and peak-peak voltage of the square wave.
|
|
|
- William Phillips
- 5 years ago
- Views:
Transcription
1 Equipment Review To assure that everyone is up to speed for the hurdles ahead, the first lab of the semester is traditionally an easy review of electrical laboratory fundamentals. There will, however, be a short write-up required of each student. Each student must turn in a report showing the names of his group's members, a signed scope trace printout, the signed sheet of current sensor data, and the current sensor analysis. Student Preparation. Students who have neglected to carefully read this document may reasonably expect to take some lumps in the course of this review. Careful preparation includes, but is not necessarily limited to, the following: (i) Review of what a variable resistor (rheostat) is and does. (ii) Review how the power supplies in Urbauer 115 are correctly wired into a circuit and how their outputs are controlled. (iii) Review of the correct ways of connecting a digital multimeter (DMM) to measure current, voltage, and resistance. (iv) Review of how to use the HP Model 4261 LCR meter. (v) Consult a reference book to discover how to use a Variable Transformer (Variac). Individual lab reports are the rule for Equipment Review, Batteries, Single Phase Transformers, Synchronous Machines, and Induction Motors. All other lab reports will be assigned to one or another of the partners. Equipment Review - 1 -
2 1a. Rheostats. Somehow determine the maximum and minimum resistances of the left power rheostat. Conclude by setting the resistance to one-half its maximum value; leave the left rheostat at this value for the remainder of Section 1. Note that each rheostat has a maximum rated current of 4.5 A. Finally, call over the Instructor and explain what you did and why. 1b. Connect +5 V DC (with respect to lab ground) to the left end of the left rheostat s winding, connect the wiper arm to the left end of the right rheostat, and connect the right end of the right rheostat to 5 V DC (with respect to lab ground). Do NOT turn the power supplies on yet. 1c. Insert an ammeter into the circuit. Place a voltmeter across the right rheostat. Calculate the expected current and voltage. Then call the Instructor over and have your work checked. 1d. Lastly, with the Instructor watching, switch the power on and see what happens. In particular, calculate the percent deviation between your measurements and your calculations. 1e. Turn the power off, disconnect everything, and neaten up the work area. 2a. Oscilloscope and Function Generator. Connect PP the output of Probe Comp to Channel 1 input using a 10X Probe. PPTurn on scope by pressing "ON/STBY" and follow the instructions on the screen. Press Power on. Press "AUTOSET" to obtain a trace. Press "DISPLAY". Press "INTENSITY" and use the "General Purpose" knob to vary the intensity. Press "Graticule Full" and change the screen with "Full" and "Frame". Press "Style Vectors". Press "Clear Menu". Press Auto-Scale and observe and understand upper status line. Press 1 to turn on Channel 1 options. 2b. Press Coupling Change the and horizontal set coupling sweep to "SEC/DIV' DC. control and observe the effect. 2c. Connect the output of the HP3310A Function Generator to CH1 input of the scope. Press Quick Meas and measure frequency, period, and peak-peak voltage of the square wave. Set the 3310A output to a 2 Vp-p sine wave at frequency of 1 khz. Press "AUTOSET" to obtain a stable display on the screen. Vary the horizontal position and the vertical position controls and observe the effects. Press Cursors and use the appropriate X and Y functions to measure period and peak-peak voltage of the square wave. Change the vertical "VOLTS/DIV" control and observe the effect. Change the horizontal sweep 'SEC/DIV" control and observe the effect. Press "TRIGGER MENU'. Press "CH1 '. The sweep triggering will be obtained from CH1. Press "Ext" and connect "Sync Output" on the 331 OA to "EXT TRIG" on the scope. The sweep triggering will be obtained from the 331 OA. Press "CLEAR MENU'. Vary the DC offset control (+/-) on the 331 OA and observe the display. Adjust Horizontal time scale (sweep) knob and observe the effect on the square wave. It is taken for granted in this course that the student will carefully look up any word or phrase which he does not understand. You learn something every time you do so. And it can save a lot of embarrassment. Equipment Review - 2 -
3 Adjust horizontal position (left-right arrows) knob and observe the effect on the square wave. Set the offset to I V positive. Press "VERTICAL MENU". Press "AC" and observe the effect on the display. Press "GND" and observe the effect on the display. Press "DC" and observe the effect on the display. Press "CLEAR MENU'. Press "MEASURE". Press "Period" and note the measured value. Press "Frequency" and note the measured value. Press "PK-PK" and note the measured value. Press "Remove Measrment" to remove measured values. Press "Select Measrment". Press "CLEAR MENU". Press "CURSOR". Use the "H Bars" to measure the voltage. Use the "General Purpose" knob and 'TOGGLE" to move the bars. Use the "V Bars" to measure the period. Adjust vertical voltage scale (amplitude) knob and observe the effect on the square wave. Adjust vertical position (up-down arrows) knob and observe the effect on the square wave. Adjust trigger level knob to 6 volts and observe the effect on the square wave. Press Run/Stop and observe resulting display. Press Run/Stop again. Connect the output of Probe Comp to Channel 2 input using a second 10X Probe. Press 2 and then Auto-Scale and observe the display. Press 'Off". Press "CLEAR MENU" 2b. Observe square and triangular outputs of the 3310A function generator at various frequencies. Connect the sync output of the 3310A to CH2 of the scope and observe the wave shape relative to the output of the 3310A that is displayed on CH1. 2c. Print a copy of the scope display using the Oscilloscope Display Hardcopy Directions. 3. Hall Effect Current Gun Clamp-on Probe. This device has two ranges, one of 10 A maximum and the other of 100 A maximum. We shall take for granted the probe's behavior at large currents and study its behavior at small currents. Use the Load Box (see diagram at end of handout) to connect the DC wall outlet (allegedly set to 25 V) in series with a digital readout DC current measuring device, i.e., AC/DC Current Shunt with DMM to measure voltage across it, and the two 50- rheostats to obtain a metered source driving a load which can be varied from 0 to 100. Also, use a Hall effect current probe connected to the other DMM to measure the current in the circuit. Vary the current from 0.25 A to 4.25 A in steps of 0.5 A. Carefully record the readings of the DMMs connected to the shunt and the Hall effect current probe. 4. Maximum power. A circuit diagram of the Load Box is provided later in this document. In this review, the Load Box will be used as a source of a large inductor of approximately 10 mh and 2. Using the Hewlett-Packard model 4261A LCR meter, determine the resistance and inductance of your load box s inductor. Then connect the load box in series with the A description of the physical principles behind this probe can be found in the chapter on Power Measurements. Operating manuals for the several different types of current sensors you will use during the course are given below. Equipment Review - 3 -
4 parallel combination of the two rheostats; denote this parallel combination as R. Power the load box by way of a 60 Hz AC Variac set to an output voltage of roughly 25 Vrms. By measuring the voltage across R with a DMM and the current through R with a DMM, determine the power P(R) dissipated in R as a function of its resistance. Adjust R until P(R) is a maximum. Measure the resistance of R at this maximum. 5. Clean Up. Turn off all electrical equipment. Put away all miscellaneous items you collected for the experiments. Tidy up your area. 6. Object Lesson. Finally, head for the two drawers labelled banana cord set and straighten their contents. Reflect that neatness in stowing equipment makes life a lot more pleasant for those who come after you. Report for Equipment Review. A. The Cover Page shall contain the experiment title, the date of the experiment, your name, the names of the group's members, and the signed disclaimer. Include also: B. The signed printout of the scope trace. C. The measured and calculated values from Part 1d. D. The signed data sheet for the currents. E. A plot of the Hall Effect Current Gun probe current versus the shunt current and a linear regression of one versus the other. F. A laconic and lucid discussion of D. G. A sheet containing your detailed theoretical prediction of the rheostat resistance that absorbed maximum power and the experimentally determined value of this resistance. Include the experimental data. Comment informatively. If you have prepared by carefully reading the handouts, you will know who is supposed to have signed what. Equipment Review - 4 -
5 Equipment Review - 5 -
6 Equipment Review - 6 -
7 Equipment Review - 7 -
8 Equipment Review - 8 -
9 Equipment Review - 9 -
10 Equipment Review
Faculty of Engineering, Thammasat University
Faculty of Engineering, Thammasat University Experiment 6: Oscilloscope (For room 506) Objectives: 1. To familiarize you with the Oscilloscope and Function Generator User Manual: Oscilloscope 1 5 9 4 7
EENG-201 Experiment # 4: Function Generator, Oscilloscope
EENG-201 Experiment # 4: Function Generator, Oscilloscope I. Objectives Upon completion of this experiment, the student should be able to 1. To become familiar with the use of a function generator. 2.
Introduction to Basic Laboratory Instruments
Introduction to Contents: 1. Objectives... 2 2. Laboratory Safety... 2 3.... 2 4. Using a DC Power Supply... 2 5. Using a Function Generator... 3 5.1 Turn on the Instrument... 3 5.2 Setting Signal Type...
Sept 13 Pre-lab due Sept 12; Lab memo due Sept 19 at the START of lab time, 1:10pm
Sept 13 Pre-lab due Sept 12; Lab memo due Sept 19 at the START of lab time, 1:10pm EGR 220: Engineering Circuit Theory Lab 1: Introduction to Laboratory Equipment Pre-lab Read through the entire lab handout
Introduction to basic laboratory instruments
Introduction to basic laboratory instruments 1. OBJECTIVES... 2 2. LABORATORY SAFETY... 2 3. BASIC LABORATORY INSTRUMENTS... 2 4. USING A DC POWER SUPPLY... 2 5. USING A FUNCTION GENERATOR... 3 5.1 TURN
Appendix A: Laboratory Equipment Manual
Appendix A: Laboratory Equipment Manual 1. Introduction: This appendix is a manual for equipment used in experiments 1-8. As a part of this series of laboratory exercises, students must acquire a minimum
Laboratory Equipment Instruction Manual 2011
University of Toronto Department of Electrical and Computer Engineering Instrumentation Laboratory GB341 Laboratory Equipment Instruction Manual 2011 Page 1. Wires and Cables A-2 2. Protoboard A-3 3. DC
The Oscilloscope. Vision is the art of seeing things invisible. J. Swift ( ) OBJECTIVE To learn to operate a digital oscilloscope.
The Oscilloscope Vision is the art of seeing things invisible. J. Swift (1667-1745) OBJECTIVE To learn to operate a digital oscilloscope. THEORY The oscilloscope, or scope for short, is a device for drawing
ME 365 EXPERIMENT 1 FAMILIARIZATION WITH COMMONLY USED INSTRUMENTATION
Objectives: ME 365 EXPERIMENT 1 FAMILIARIZATION WITH COMMONLY USED INSTRUMENTATION The primary goal of this laboratory is to study the operation and limitations of several commonly used pieces of instrumentation:
LABORATORY 4. Palomar College ENGR210 Spring 2017 ASSIGNED: 3/21/17
LABORATORY 4 ASSIGNED: 3/21/17 OBJECTIVE: The purpose of this lab is to evaluate the transient and steady-state circuit response of first order and second order circuits. MINIMUM EQUIPMENT LIST: You will
Lab 0: Introduction to basic laboratory instruments. Revised by Dan Hoang & Tai-Chang Chen 03/30/2009
Lab 0: Introduction to basic laboratory instruments Revised by Dan Hoang & Tai-Chang Chen 03/30/2009 1. Objectives 1. To learn safety procedures in the laboratory. 2. To learn how to use basic laboratory
UNIVERSITY OF CALIFORNIA, SANTA BARBARA Department of Electrical and Computer Engineering. ECE 2A & 2B Laboratory Equipment Information
UNIVERSITY OF CALIFORNIA, SANTA BARBARA Department of Electrical and Computer Engineering ECE 2A & 2B Laboratory Equipment Information Table of Contents Digital Multi-Meter (DMM)... 1 Features... 1 Using
CHAPTER 6. Motor Driver
CHAPTER 6 Motor Driver In this lab, we will construct the circuitry that your robot uses to drive its motors. However, before testing the motor circuit we will begin by making sure that you are able to
Lab: INTRODUCTION TO THE WAVEFORM GENERATOR AND THE OSCILLOSCOPE
Name EET101/Lab#5; EET121/Lab#5; EGR104/Lab#3 Sec / Night Date Lab Partner(s) Name(s) Lab: INTRODUCTION TO THE WAVEFORM GENERATOR AND THE OSCILLOSCOPE Objectives: Each student will: 1. Know the function
Introduction to oscilloscope. and time dependent circuits
Physics 9 Intro to oscilloscope, v.1.0 p. 1 NAME: SECTION DAY/TIME: TA: LAB PARTNER: Introduction to oscilloscope and time dependent circuits Introduction In this lab, you ll learn the basics of how to
Equipment: You will use the bench power supply, function generator and oscilloscope.
EE203 Lab #0 Laboratory Equipment and Measurement Techniques Purpose Your objective in this lab is to gain familiarity with the properties and effective use of the lab power supply, function generator
Lab #1 Lab Introduction
Cir cuit s 212 Lab Lab #1 Lab Introduction Special Information for this Lab s Report Because this is a one-week lab, please hand in your lab report for this lab at the beginning of next week s lab. The
The University of Jordan Mechatronics Engineering Department Electronics Lab.( ) Experiment 1: Lab Equipment Familiarization
The University of Jordan Mechatronics Engineering Department Electronics Lab.(0908322) Experiment 1: Lab Equipment Familiarization Objectives To be familiar with the main blocks of the oscilloscope and
Introduction to basic laboratory instruments
BEE 233 Laboratory-1 Introduction to basic laboratory instruments 1. Objectives To learn safety procedures in the laboratory. To learn how to use basic laboratory instruments: power supply, function generator,
Exercise 4 - THE OSCILLOSCOPE
Exercise 4 - THE OSCILLOSCOPE INTRODUCTION You have been exposed to analogue oscilloscopes in the first year lab. As you are probably aware, the complexity of the instruments, along with their importance
Resonant Frequency of the LRC Circuit (Power Output, Voltage Sensor)
72 Resonant Frequency of the LRC Circuit (Power Output, Voltage Sensor) Equipment List Qty Items Part Numbers 1 PASCO 750 Interface 1 Voltage Sensor CI-6503 1 AC/DC Electronics Laboratory EM-8656 2 Banana
Experiment 8: An AC Circuit
Experiment 8: An AC Circuit PART ONE: AC Voltages. Set up this circuit. Use R = 500 Ω, L = 5.0 mh and C =.01 μf. A signal generator built into the interface provides the emf to run the circuit from Output
ECE 53A: Fundamentals of Electrical Engineering I
ECE 53A: Fundamentals of Electrical Engineering I Laboratory Assignment #1: Instrument Operation, Basic Resistor Measurements and Kirchhoff s Laws Fall 2007 General Guidelines: - Record data and observations
University of Jordan School of Engineering Electrical Engineering Department. EE 204 Electrical Engineering Lab
University of Jordan School of Engineering Electrical Engineering Department EE 204 Electrical Engineering Lab EXPERIMENT 1 MEASUREMENT DEVICES Prepared by: Prof. Mohammed Hawa EXPERIMENT 1 MEASUREMENT
Experiment 1: Instrument Familiarization
Electrical Measurement Issues Experiment 1: Instrument Familiarization Electrical measurements are only as meaningful as the quality of the measurement techniques and the instrumentation applied to the
EE 210: CIRCUITS AND DEVICES
EE 210: CIRCUITS AND DEVICES LAB #3: VOLTAGE AND CURRENT MEASUREMENTS This lab features a tutorial on the instrumentation that you will be using throughout the semester. More specifically, you will see
ENGR 1110: Introduction to Engineering Lab 7 Pulse Width Modulation (PWM)
ENGR 1110: Introduction to Engineering Lab 7 Pulse Width Modulation (PWM) Supplies Needed Motor control board, Transmitter (with good batteries), Receiver Equipment Used Oscilloscope, Function Generator,
Laboratory 3 (drawn from lab text by Alciatore)
Laboratory 3 (drawn from lab text by Alciatore) The Oscilloscope Required Components: 1 10 resistor 2 100 resistors 2 lk resistors 1 2k resistor 2 4.7M resistors 1 0.F capacitor 1 0.1 F capacitor 1 1.0uF
Experiment 1: Instrument Familiarization (8/28/06)
Electrical Measurement Issues Experiment 1: Instrument Familiarization (8/28/06) Electrical measurements are only as meaningful as the quality of the measurement techniques and the instrumentation applied
Experiment #2: Introduction to Lab Equipment: Function Generator, Oscilloscope, and Multisim
SCHOOL OF ENGINEERING AND APPLIED SCIENCE DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING ECE 2110: CIRCUIT THEORY LABORATORY Experiment #2: Introduction to Lab Equipment: Function Generator, Oscilloscope,
LAB 7: THE OSCILLOSCOPE
LAB 7: THE OSCILLOSCOPE Equipment List: Dual Trace Oscilloscope HP function generator HP-DMM 2 BNC-to-BNC 1 cables (one long, one short) 1 BNC-to-banana 1 BNC-probe Hand-held DMM (freq mode) Purpose: To
Precalculations Individual Portion Introductory Lab: Basic Operation of Common Laboratory Instruments
Name: Date of lab: Section number: M E 345. Lab 1 Precalculations Individual Portion Introductory Lab: Basic Operation of Common Laboratory Instruments Precalculations Score (for instructor or TA use only):
AME140 Lab #2 INTRODUCTION TO ELECTRONIC TEST EQUIPMENT AND BASIC ELECTRONICS MEASUREMENTS
INTRODUCTION TO ELECTRONIC TEST EQUIPMENT AND BASIC ELECTRONICS MEASUREMENTS The purpose of this document is to guide students through a few simple activities to increase familiarity with basic electronics
CPE 310L EMBEDDED SYSTEM DESIGN LABORATORY
CPE 310L EMBEDDED SYSTEM DESIGN LABORATORY LABORATORY 1 LAB SAFETY & LAB EQUIPMENT USE TUTORIAL DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING UNIVERSITY OF NEVADA, LAS VEGAS GOALS: Introduce laboratory
EXPERIMENT NUMBER 2 BASIC OSCILLOSCOPE OPERATIONS
1 EXPERIMENT NUMBER 2 BASIC OSCILLOSCOPE OPERATIONS The oscilloscope is the most versatile and most important tool in this lab and is probably the best tool an electrical engineer uses. This outline guides
Ahsanullah University of Science and Technology
Ahsanullah University of Science and Technology Department of Electrical and Electronic Engineering AU ST /E EE LABORATORY MANUAL FOR ELECTRICAL AND ELECTRONIC SESSIONAL COURSE Student Name : Student ID
Physics 120 Lab 1 (2018) - Instruments and DC Circuits
Physics 120 Lab 1 (2018) - Instruments and DC Circuits Welcome to the first laboratory exercise in Physics 120. Your state-of-the art equipment includes: Digital oscilloscope w/usb output for SCREENSHOTS.
Lab 6 Instrument Familiarization
Lab 6 Instrument Familiarization What You Need To Know: Voltages and currents in an electronic circuit as in a CD player, mobile phone or TV set vary in time. Throughout todays lab you will investigate
PHYSICS 171 UNIVERSITY PHYSICS LAB II. Experiment 4. Alternating Current Measurement
PHYSICS 171 UNIVERSITY PHYSICS LAB II Experiment 4 Alternating Current Measurement Equipment: Supplies: Oscilloscope, Function Generator. Filament Transformer. A sine wave A.C. signal has three basic properties:
Lab 1: Basic Lab Equipment and Measurements
Abstract: Lab 1: Basic Lab Equipment and Measurements This lab exercise introduces the basic measurement instruments that will be used throughout the course. These instruments include multimeters, oscilloscopes,
Group: Names: Resistor Band Colors Measured Value ( ) R 1 : 1k R 2 : 1k R 3 : 2k R 4 : 1M R 5 : 1M
2.4 Laboratory Procedure / Summary Sheet Group: Names: (1) Select five separate resistors whose nominal values are listed below. Record the band colors for each resistor in the table below. Then connect
UNIVERSITY OF TECHNOLOGY, JAMAICA SCHOOL OF ENGENEERING. Electrical Engineering Science. Laboratory Manual
UNIVERSITY OF TECHNOLOGY, JAMAICA SCHOOL OF ENGENEERING Electrical Engineering Science Laboratory Manual Table of Contents Experiment #1 OHM S LAW... 3 Experiment # 2 SERIES AND PARALLEL CIRCUITS... 8
Name EET 1131 Lab #2 Oscilloscope and Multisim
Name EET 1131 Lab #2 Oscilloscope and Multisim Section 1. Oscilloscope Introduction Equipment and Components Safety glasses Logic probe ETS-7000 Digital-Analog Training System Fluke 45 Digital Multimeter
Notes on Experiment #1
Notes on Experiment #1 Bring graph paper (cm cm is best) From this week on, be sure to print a copy of each experiment and bring it with you to lab. There will not be any experiment copies available in
2 Oscilloscope Familiarization
Lab 2 Oscilloscope Familiarization What You Need To Know: Voltages and currents in an electronic circuit as in a CD player, mobile phone or TV set vary in time. Throughout the course you will investigate
Voltage Current and Resistance II
Voltage Current and Resistance II Equipment: Capstone with 850 interface, analog DC voltmeter, analog DC ammeter, voltage sensor, RLC circuit board, 8 male to male banana leads 1 Purpose This is a continuation
Experiment P45: LRC Circuit (Power Amplifier, Voltage Sensor)
PASCO scientific Vol. 2 Physics Lab Manual: P45-1 Experiment P45: (Power Amplifier, Voltage Sensor) Concept Time SW Interface Macintosh file Windows file circuits 30 m 700 P45 P45_LRCC.SWS EQUIPMENT NEEDED
Sirindhorn International Institute of Technology Thammasat University at Rangsit
Sirindhorn International Institute of Technology Thammasat University at Rangsit School of Information, Computer and Communication Technology COURSE : ECS 210 Basic Electrical Engineering Lab INSTRUCTOR
Virtual Lab 1: Introduction to Instrumentation
Virtual Lab 1: Introduction to Instrumentation By: Steve Badelt and Daniel D. Stancil Department of Electrical and Computer Engineering Carnegie Mellon University Pittsburgh, PA Purpose: Measurements and
Agilent 33522A Function Arbitrary Waveform Generator. Tektronix TDS 3012B Oscilloscope
Agilent 33522A Function/Arbitrary Waveform Generator and Tektronix TDS 3012B Oscilloscope Agilent 33522A Function Arbitrary Waveform Generator The signal source for this lab is the Agilent 33522A Function
Experiment 9 The Oscilloscope and Function Generator
Experiment 9 The Oscilloscope and Function Generator Introduction The oscilloscope is one of the most important electronic instruments available for making circuit measurements. It displays a curve plot
ECE 480: SENIOR DESIGN LABORATORY
ECE 480: SENIOR DESIGN LABORATORY DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING MICHIGAN STATE UNIVERSITY I. TITLE: Lab I - Introduction to the Oscilloscope, Function Generator, Digital Multimeter
University of California, San Diego Department of Electrical and Computer Engineering
University of California, San Diego Department of Electrical and Computer Engineering Part One: Introduction of Lab TAs ECE65, Spring 2007 Lab 0, ECE 65 Lab Orientation 1) James Liao, geniojames@yahoo.com
University of Pennsylvania Department of Electrical and Systems Engineering. ESE 206: Electrical Circuits and Systems II - Lab
University of Pennsylvania Department of Electrical and Systems Engineering ESE 206: Electrical Circuits and Systems II - Lab AC POWER ANALYSIS AND DESIGN I. Purpose and Equipment: Provide experimental
ECE65 Introduction to the Function Generator and the Oscilloscope Created by: Eldridge Alcantara (Spring 2007)
ECE65 Introduction to the Function Generator and the Oscilloscope Created by: Eldridge Alcantara (Spring 2007) I. Getting Started with the Function Generator OUTPUT Red Clip Small Black Clip 1) Turn on
The oscilloscope and RC filters
(ta initials) first name (print) last name (print) brock id (ab17cd) (lab date) Experiment 4 The oscilloscope and C filters The objective of this experiment is to familiarize the student with the workstation
University of Jordan School of Engineering Electrical Engineering Department. EE 219 Electrical Circuits Lab
University of Jordan School of Engineering Electrical Engineering Department EE 219 Electrical Circuits Lab EXPERIMENT 4 TRANSIENT ANALYSIS Prepared by: Dr. Mohammed Hawa EXPERIMENT 4 TRANSIENT ANALYSIS
LAB I. INTRODUCTION TO LAB EQUIPMENT
LAB I. INTRODUCTION TO LAB EQUIPMENT 1. OBJECTIVE In this lab you will learn how to properly operate the basic bench equipment used for characterizing active devices: 1. Oscilloscope (Keysight DSOX 1102A),
Laboratory Exercise 6 THE OSCILLOSCOPE
Introduction Laboratory Exercise 6 THE OSCILLOSCOPE The aim of this exercise is to introduce you to the oscilloscope (often just called a scope), the most versatile and ubiquitous laboratory measuring
ECE 6416 Low-Noise Electronics Orientation Experiment
ECE 6416 Low-Noise Electronics Orientation Experiment Object The object of this experiment is to become familiar with the instruments used in the low noise laboratory. Parts The following parts are required
Physics 310 Lab 2 Circuit Transients and Oscilloscopes
Physics 310 Lab 2 Circuit Transients and Oscilloscopes Equipment: function generator, oscilloscope, two BNC cables, BNC T connector, BNC banana adapter, breadboards, wire packs, some banana cables, three
UNIVERSITY OF TECHNOLOGY, JAMAICA School of Engineering -
UNIVERSITY OF TECHNOLOGY, JAMAICA School of Engineering - Electrical Engineering Science Laboratory Manual Table of Contents Safety Rules and Operating Procedures... 3 Troubleshooting Hints... 4 Experiment
LAB 2 Circuit Tools and Voltage Waveforms
LAB 2 Circuit Tools and Voltage Waveforms OBJECTIVES 1. Become familiar with a DC power supply and setting the output voltage. 2. Learn how to measure voltages & currents using a Digital Multimeter. 3.
Experiment 13: LR Circuit
012-05892A AC/DC Electronics Laboratory Experiment 13: LR Circuit Purpose Theory EQUIPMENT NEEDED: Computer and Science Workshop Interface Power Amplifier (CI-6552A) (2) Voltage Sensor (CI-6503) AC/DC
Physics 323. Experiment # 1 - Oscilloscope and Breadboard
Physics 323 Experiment # 1 - Oscilloscope and Breadboard Introduction In order to familiarise yourself with the laboratory equipment, a few simple experiments are to be performed. References: XYZ s of
Integrators, differentiators, and simple filters
BEE 233 Laboratory-4 Integrators, differentiators, and simple filters 1. Objectives Analyze and measure characteristics of circuits built with opamps. Design and test circuits with opamps. Plot gain vs.
Exercise 1: Inductors
Exercise 1: Inductors EXERCISE OBJECTIVE When you have completed this exercise, you will be able to describe the effect an inductor has on dc and ac circuits by using measured values. You will verify your
ENG 100 Lab #2 Passive First-Order Filter Circuits
ENG 100 Lab #2 Passive First-Order Filter Circuits In Lab #2, you will construct simple 1 st -order RL and RC filter circuits and investigate their frequency responses (amplitude and phase responses).
total j = BA, [1] = j [2] total
![total j = BA, [1] = j [2] total](/thumbs/85/91692343.jpg "total j = BA, [1] = j [2] total")
Name: S.N.: Experiment 2 INDUCTANCE AND LR CIRCUITS SECTION: PARTNER: DATE: Objectives Estimate the inductance of the solenoid used for this experiment from the formula for a very long, thin, tightly wound
POLYTECHNIC UNIVERSITY Electrical Engineering Department. EE SOPHOMORE LABORATORY Experiment 3 The Oscilloscope
POLYTECHNIC UNIVERSITY Electrical Engineering Department EE SOPHOMORE LABORATORY Experiment 3 The Oscilloscope Modified for Physics 18, Brooklyn College I. Overview of the Experiment The main objective
PHYSICS 221 LAB #6: CAPACITORS AND AC CIRCUITS
Name: Partners: PHYSICS 221 LAB #6: CAPACITORS AND AC CIRCUITS The electricity produced for use in homes and industry is made by rotating coils of wire in a magnetic field, which results in alternating
CPE 100L DIGITAL LOGIC DESIGN I DESIGN LABORATORY LABORATORY 1 LAB SAFETY QUIZ & LAB EQUIPMENT USE TUTORIAL UNIVERSITY OF NEVADA, LAS VEGAS GOALS:
CPE 100L DESIGN LABORATORY LABORATORY 1 LAB SAFETY QUIZ & LAB EQUIPMENT USE TUTORIAL DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING UNIVERSITY OF NEVADA, LAS VEGAS GOALS: Introduce laboratory safety
Name: First-Order Response: RC Networks Objective: To gain experience with first-order response of RC circuits
First-Order Response: RC Networks Objective: To gain experience with first-order response of RC circuits Table of Contents: Pre-Lab Assignment 2 Background 2 National Instruments MyDAQ 2 Resistors 3 Capacitors
EE-4022 Experiment 2 Amplitude Modulation (AM)
EE-4022 MILWAUKEE SCHOOL OF ENGINEERING 2015 Page 2-1 Student objectives: EE-4022 Experiment 2 Amplitude Modulation (AM) In this experiment the student will use laboratory modules to implement operations
Experiment 5 The Oscilloscope
Experiment 5 The Oscilloscope Vision is the art of seeing things invisible. J. Swift (1667-1745) OBJECTIVE To learn to operate a cathode ray oscilloscope. THEORY The oscilloscope, or scope for short, is
EC310 Security Exercise 20
EC310 Security Exercise 20 Introduction to Sinusoidal Signals This lab demonstrates a sinusoidal signal as described in class. In this lab you will identify the different waveform parameters for a pure
Fig. 1. NI Elvis System
Lab 2: Introduction to I Elvis Environment. Objectives: The purpose of this laboratory is to provide an introduction to the NI Elvis design and prototyping environment. Basic operations provided by Elvis
Tektronix digital oscilloscope, BK Precision Function Generator, coaxial cables, breadboard, the crystal earpiece from your AM radio kit.
Experiment 0: Review I. References The 174 and 275 Lab Manuals Any standard text on error analysis (for example, Introduction to Error Analysis, J. Taylor, University Science Books, 1997) The manual for
On-Line Students Analog Discovery 2: Arbitrary Waveform Generator (AWG). Two channel oscilloscope
EET 150 Introduction to EET Lab Activity 5 Oscilloscope Introduction Required Parts, Software and Equipment Parts Figure 1, Figure 2, Figure 3 Component /Value Quantity Resistor 10 kω, ¼ Watt, 5% Tolerance
Electric Circuit II Lab Manual Session #1
Department of Electrical Engineering Electric Circuit II Lab Manual Session #1 Subject Lecturer Dr. Yasser Hegazy Name:-------------------------------------------------- Group:--------------------------------------------------
The object of this experiment is to become familiar with the instruments used in the low noise laboratory.
0. ORIENTATION 0.1 Object The object of this experiment is to become familiar with the instruments used in the low noise laboratory. 0.2 Parts The following parts are required for this experiment: 1. A
Sonoma State University Department of Engineering Science Spring 2017
EE 110 Introduction to Engineering & Laboratory Experience Saeid Rahimi, Ph.D. Lab 4 Introduction to AC Measurements (I) AC signals, Function Generators and Oscilloscopes Function Generator (AC) Battery
54645D. Mixed Signal Oscilloscope
54645D Mixed Signal Oscilloscope Page 1 of 42 Instructions for the use of the 54645D Mixed Signal Oscilloscope This pamphlet is intended to give you (the student) an overview on the use of the 54645D Mixed
Time-Varying Signals
Time-Varying Signals Objective This lab gives a practical introduction to signals that varies with time using the components such as: 1. Arbitrary Function Generator 2. Oscilloscopes The grounding issues
LAB I. INTRODUCTION TO LAB EQUIPMENT
1. OBJECTIVE LAB I. INTRODUCTION TO LAB EQUIPMENT In this lab you will learn how to properly operate the oscilloscope Agilent MSO6032A, the Keithley Source Measure Unit (SMU) 2430, the function generator
2 AC and RMS. To pass this lab you must solve tasks 1-2. Tasks 3 and 4 are included in the grading of the course.
2 AC and RMS Purpose of the lab: to familiarize yourself with the oscilloscope to familiarize yourself with AC voltages and different waveforms to study RMS and average values In this lab, you have the
ENGR 210 Lab 6 Use of the Function Generator & Oscilloscope
ENGR 210 Lab 6 Use of the Function Generator & Oscilloscope In this laboratory you will learn to use two additional instruments in the laboratory, namely the function/arbitrary waveform generator, which
WELCOME TO PHYC 307L Junior Lab II
WELCOME TO PHYC 307L Junior Lab II Spring Semester 2019 Instructor: Dr Michael Hasselbeck Challenging Modern Physics experiments Require independent problem solving harder than intro physics labs 10 experiments
Lab 1: Basic RL and RC DC Circuits
Name- Surname: ID: Department: Lab 1: Basic RL and RC DC Circuits Objective In this exercise, the DC steady state response of simple RL and RC circuits is examined. The transient behavior of RC circuits
Basic Electronics: Carnegie Mellon Lab Manual. Edited by Curtis A. Meyer
Basic Electronics: Carnegie Mellon Lab Manual Edited by Curtis A. Meyer ii COPYRIGHT c 2012 Carnegie Mellon Department of Physics and Curtis A. Meyer ALL RIGHTS RESERVED. No part of this work covered by
Experiment # 1 Introduction to Lab Equipment
Experiment # 1 Introduction to Lab Equipment 1. Synopsis: In this introductory lab, we will review the basic concepts of digital logic design and learn how to use the equipment available in the laboratory.
ECE ECE285. Electric Circuit Analysis I. Spring Nathalia Peixoto. Rev.2.0: Rev Electric Circuits I
ECE285 Electric Circuit Analysis I Spring 2014 Nathalia Peixoto Rev.2.0: 140124. Rev 2.1. 140813 1 Lab reports Background: these 9 experiments are designed as simple building blocks (like Legos) and students
EE2210 Laboratory Project 1 Fall 2013 Function Generator and Oscilloscope
EE2210 Laboratory Project 1 Fall 2013 Function Generator and Oscilloscope For students to become more familiar with oscilloscopes and function generators. Pre laboratory Work Read the TDS 210 Oscilloscope
PHY152 Experiment 4: Oscillations in the RC-Circuits (Measurements with an oscilloscope)
PHY152 Experiment 4: Oscillations in the RC-Circuits (Measurements with an oscilloscope) If you have not used an oscilloscope before, the web site http://www.upscale.utoronto.ca/generalinterest/harrison/oscilloscope/oscilloscope.html
resistor box inductor 3 BNC to banana + V L
Physics ab II Inductance and Circuit Page 1/5 Name: Partner: Partner: Purpose: To investigate how the voltage across an inductor changes in response to changing currents. To measure the inductance by measuring
EECS 318 Electronics Lab Laboratory #2 Electronic Test Equipment
EECS 318 Electronics Lab Laboratory #2 Electronic Test Equipment Objectives: The purpose of this laboratory is to acquaint you with the electronic sources and measuring equipment you will be using throughout
Laboratory 2 (drawn from lab text by Alciatore)
Laboratory 2 (drawn from lab text by Alciatore) Instrument Familiarization and Basic Electrical Relations Required Components: 2 1k resistors 2 1M resistors 1 2k resistor Objectives This exercise is designed
Frequency and Time Domain Representation of Sinusoidal Signals
Frequency and Time Domain Representation of Sinusoidal Signals By: Larry Dunleavy Wireless and Microwave Instruments University of South Florida Objectives 1. To review representations of sinusoidal signals
Oscilloscope Measurements
PC1143 Physics III Oscilloscope Measurements 1 Purpose Investigate the fundamental principles and practical operation of the oscilloscope using signals from a signal generator. Measure sine and other waveform
1. Hand Calculations (in a manner suitable for submission) For the circuit in Fig. 1 with f = 7.2 khz and a source vin () t 1.
Objectives The purpose of this laboratory project is to introduce to equipment, measurement techniques, and simulations commonly used in AC circuit analysis. In this laboratory session, each student will: