Lecture 19 Transistor Amplifiers (I) Common Source Amplifier. November 15, 2005
|
|
- Drusilla Dawson
- 5 years ago
- Views:
Transcription
1 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture 19 1 Lecture 19 Transistor Amplifiers (I) Common Source Amplifier November 15, 2005 Contents: 1. Amplifier fundamentals 2. Common source amplifier 3. Common source amplifier with current source supply Reading assignment: Howe and Sodini, Ch. 8, Announcements: Quiz 2: 11/16, 7:30 9:30 PM, open book, must bring calculator; lectures # Quiz 2 TA Review Session: 11/15, 7:30 9:30 PM,
2 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture 19 2 Key questions What are the key figures of merit of an amplifier? How can one make a voltage amplifier with a single MOSFET and a resistor? How can this amplifier be improved?
3 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture Amplifier fundamentals Goal of amplifiers: signal amplification. V v OUT v IN R L vout output signal v IN V input signal Features of amplifier: Output signal is faithful replica of input signal but amplified in magnitude. Active device is at the heart of amplifier. Need linear transfer characteristics for distortion not to be introduced.
4 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture 19 4 Signal could be represented by current or voltage four broad types of amplifiers: voltage v s R L v amplifier out i out transconductance amplifier R L i s transresistance amplifier RL v out i out i s current amplifier R L
5 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture 19 5 More realistic transfer characteristics: v OUT Q output signal v IN input signal Transfer characteristics linear over limited range of voltages: amplifier saturation. Amplifier saturation limits signal swing. Signal swing also depends on choice of bias point, Q (also called quiescent point or operating point). Other features desired in amplifiers: Low power consumption. Wide frequency response [will discuss in a few days]. Robust to process and temperature variations. Inexpensive: must minimize use of unusual components, must be small (in Si area)
6 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture Common Source Amplifier Consider the following circuit: V =V DD R D i R signal source i D signal load v OUT R L V GG V =V SS Consider it first unloaded by R L. How does it work? V GG, R D and W/L of MOSFET selected to bias transistor in saturation and obtain desired output bias point (i.e. V OU T = 0). v GS i D i R v out A v = v out < 0; output out of phase from input, but if amplifier well designed, A v > 1. [watch notation: v OU T (t) = V OU T v out (t)]
7 0 VSS V DD V OUT V SS 0 VT V DD V SS V GG V SS Microelectronic Devices and Circuits Fall 2005 Lecture 19 7 Load line view of amplifier: I R =I D load line V DD V SS R D V GG V SS =V DD V SS V GG V SS V GG V SS =V T Transfer characteristics of amplifier: V OUT V DD Want: Bias point calculation; small signal gain; limits to signal swing frequency response [in a few days]
8 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture 19 8 Bias point: choice of V GG, W/L, and R D to keep transistor in saturation and to get proper quiescent V OUT. Assume MOSFET is in saturation: W I D = µ n C ox (V GG V SS V T ) 2 2L I R = V DD V OUT R D If we select V OUT =0: W I D = I R = µ n C ox (V GG V SS V T ) 2 = 2L V DD R D Then: 2V DD V GG = W V SS V T R D L µ n C ox
9 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture 19 9 Small signal voltage gain: draw small signal equivalent circuit model: R D G v in v gs gm v gs D r o v out S v in gm v in r o //R D v out v out = g m v in (r o //R D ) Then unloaded voltage gain: v out A vo = = g m (r o //R D ) v in
10 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture Signal swing: V DD signal source R D v OUT V GG V SS Upswing: limited by transistor going into cut off: v out,max = V DD Downswing: limited by MOSFET entering linear regime: V DS,sat = V GS V T or v out,min V SS = V GG V SS V T Then: v out,min = V GG V T
11 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture Effect of input/output loading: V DD signal source R D i R i D i L v OUT R L V GG Bias point not affected because selected V OU T =0. Signal swing: V SS Upswing limited by resistive divider: R L v out,max = V DD R L R D Downswing not affected by loading Voltage gain: input loading ( ): no effect because gate does not draw current; output loading (R L ): R L detracts from voltage gain because it draws current. A v = g m (r o //R D //R L ) <g m (r o //R D )
12 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture Generic view of loading effect on small signal operation: Two port network view of small signal equivalent circuit model of voltage amplifier: R in is input resistance R out is output resistance A vo is unloaded voltage gain R out v in R in Avo v in v out R L input loading unloaded circuit output loading Voltage divider at input: Voltage divider at output: v in = R inrin A vo v in v out = R LRout R L Loaded voltage gain: v out R in R L A v = = A vo R in R L R out
13 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture Calculation of input resistance, R in : load amplifier with R L apply test voltage (or current) at input, measure test current (or voltage) For common source amplifier: i t v t v gs g m v gs r o //R D R L v t i t i t =0 R in = = No effect of loading at input.
14 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture Calculation of output resistance, R out : load amplifier at input with apply test voltage (or current) at output, measure test current (or voltage) For common source amplifier: v gs g m v gs r o //R D i t vt v gs =0 g m v gs =0 v t = i t (r o //R D ) R out = v t i t = r o //R D
15 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture Two port network view of common source amplifier: Rout v in R in Avo v in v out R L input loading unloaded circuit output loading A v = v out Rin R L R L = A vo = g m (r o //R D ) R in R L R out RL r o //R D Or: A v = g m (r o //R D //R L )
16 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture Design issues of common source amplifier (unloaded): Examine bias dependence: A vo = g m (r o //R D ) g m R D Rewrite A vo in the following way: W V DD V DD A vo g m R D = 2 µ n C ox I D L I D ID Then, to get high A vo : V DD I D Both approaches imply R D = Consequences of high R D : V DD I D large R D consumes a lot of Si real state large R D eventually compromises frequency response Also, it would be nice not to use any resistors at all! Need better circuit.
17 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture Common source amplifier with current source supply V DD i SUP signal source RS i D signal load v OUT R L V GG V SS Loadline view: i SUP =I D load line V GG V SS =V DD V SS I SUP V GG V SS 0 V SS V DD V OUT V GG V SS =V T
18 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture Current source characterized by high output resistance: r oc. Then, unloaded voltage gain of common source stage: A vo = g m (r o //r oc ) significantly higher than amplifier with resistive supply. Can implement current source supply by means of p channel MOSFET: V DD V B i SUP signal source i D v OUT V GG V SS
19 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture Relationship between circuit figures of merit and device parameters Remember: g m = W 2 µ n C ox I D L 1 L r o λn I D ID Then: Circuit Parameters Device A vo R in R out Parameters g m (r o //r oc ) r o //r oc I SU P W µ n C ox L adjustments are made to V GG so none of the other parameters change CS amp with current supply source is good voltage amplifier (R in high and A v high), but R out high too voltage gain degraded if R L r o //r oc.
20 6.012 Microelectronic Devices and Circuits Fall 2005 Lecture Key conclusions Figures of merit of an amplifier: gain signal swing power consumption frequency response robustness to process and temperature variations Common source amplifier with resistive supply: tradeoff between gain and cost and frequency response. Trade off resolved by using common source amplifier with current source supply. Two port network computation of voltage gain, input resistance and output resistance of amplifier.
Lecture 19 - Transistor Amplifiers (I) Common-Source Amplifier. April 24, 2001
6.012 Microelectronic Devices and Circuits Spring 2001 Lecture 191 Lecture 19 Transistor Amplifiers (I) CommonSource Amplifier April 24, 2001 Contents: 1. Amplifier fundamentals 2. Commonsource amplifier
More informationLecture 20 Transistor Amplifiers (II) Other Amplifier Stages. November 17, 2005
6.012 Microelectronic Devices and Circuits Fall 2005 Lecture 20 1 Lecture 20 Transistor Amplifiers (II) Other Amplifier Stages November 17, 2005 Contents: 1. Common source amplifier (cont.) 2. Common drain
More informationLecture 20 Transistor Amplifiers (II) Other Amplifier Stages
Lecture 20 Transistor Amplifiers (II) Other Amplifier Stages Outline Common drain amplifier Common gate amplifier Reading Assignment: Howe and Sodini; Chapter 8, Sections 8.78.9 6.02 Spring 2009 . Common
More informationLecture 25 - Frequency Response of Amplifiers (III) Other Amplifier Stages. December 8, 2005
6.012 Microelectronic Devices and Circuits Fall 2005 Lecture 251 Lecture 25 Frequency Response of Amplifiers (III) Other Amplifier Stages December 8, 2005 Contents: 1. Frequency response of commondrain
More informationLecture 21 - Multistage Amplifiers (I) Multistage Amplifiers. November 22, 2005
6.02 Microelectronic Devices and Circuits Fall 2005 Lecture 2 Lecture 2 Multistage Amplifiers (I) Multistage Amplifiers November 22, 2005 Contents:. Introduction 2. CMOS multistage voltage amplifier 3.
More informationLecture 16: Small Signal Amplifiers
Lecture 16: Small Signal Amplifiers Prof. Niknejad Lecture Outline Review: Small Signal Analysis Two Port Circuits Voltage Amplifiers Current Amplifiers Transconductance Amps Transresistance Amps Example:
More informationLecture 34: Designing amplifiers, biasing, frequency response. Context
Lecture 34: Designing amplifiers, biasing, frequency response Prof J. S. Smith Context We will figure out more of the design parameters for the amplifier we looked at in the last lecture, and then we will
More informationEE105 - Fall 2006 Microelectronic Devices and Circuits
EE105 - Fall 2006 Microelectronic Devices and Circuits Prof. Jan M. Rabaey (jan@eecs) Lecture 11: Voltage and Current Sources Administrativia Lab 3 this week Please make sure to work through the pre-lab
More informationMultistage Amplifiers
Multistage Amplifiers Single-stage transistor amplifiers are inadequate for meeting most design requirements for any of the four amplifier types (voltage, current, transconductance, and transresistance.)
More informationChapter 4 Single-stage MOS amplifiers
Chapter 4 Single-stage MOS amplifiers ELEC-H402/CH4: Single-stage MOS amplifiers 1 Single-stage MOS amplifiers NMOS as an amplifier: example of common-source circuit NMOS amplifier example Introduction
More informationINTRODUCTION TO ELECTRONICS EHB 222E
INTRODUCTION TO ELECTRONICS EHB 222E MOS Field Effect Transistors (MOSFETS II) MOSFETS 1/ INTRODUCTION TO ELECTRONICS 1 MOSFETS Amplifiers Cut off when v GS < V t v DS decreases starting point A, once
More informationEE5310/EE3002: Analog Circuits. on 18th Sep. 2014
EE5310/EE3002: Analog Circuits EC201-ANALOG CIRCUITS Tutorial 3 : PROBLEM SET 3 Due shanthi@ee.iitm.ac.in on 18th Sep. 2014 Problem 1 The MOSFET in Fig. 1 has V T = 0.7 V, and μ n C ox = 500 μa/v 2. The
More informationWeek 9a OUTLINE. MOSFET I D vs. V GS characteristic Circuit models for the MOSFET. Reading. resistive switch model small-signal model
Week 9a OUTLINE MOSFET I vs. V GS characteristic Circuit models for the MOSFET resistive switch model small-signal model Reading Rabaey et al.: Chapter 3.3.2 Hambley: Chapter 12 (through 12.5); Section
More informationIntroduction to MOSFET MOSFET (Metal Oxide Semiconductor Field Effect Transistor)
Microelectronic Circuits Introduction to MOSFET MOSFET (Metal Oxide Semiconductor Field Effect Transistor) Slide 1 MOSFET Construction MOSFET (Metal Oxide Semiconductor Field Effect Transistor) Slide 2
More informationCMOS Cascode Transconductance Amplifier
CMOS Cascode Transconductance Amplifier Basic topology. 5 V I SUP v s V G2 M 2 iout C L v OUT Device Data V Tn = 1 V V Tp = 1 V µ n C ox = 50 µa/v 2 µ p C ox = 25 µa/v 2 λ n = 0.05 V 1 λ p = 0.02 V 1 @
More informationLecture 12 - Digital Circuits (I) The inverter. October 20, 2005
6.12 - Microelectronic Devices and Circuits - Fall 25 Lecture 12-1 Lecture 12 - Digital Circuits (I) The inverter October 2, 25 Contents: 1. Introduction to digital electronics: the inverter 2. NMOS inverter
More informationExperiment 5 Single-Stage MOS Amplifiers
Experiment 5 Single-Stage MOS Amplifiers B. Cagdaser, H. Chong, R. Lu, and R. T. Howe UC Berkeley EE 105 Fall 2005 1 Objective This is the first lab dealing with the use of transistors in amplifiers. We
More information4.5 Biasing in MOS Amplifier Circuits
4.5 Biasing in MOS Amplifier Circuits Biasing: establishing an appropriate DC operating point for the MOSFET - A fundamental step in the design of a MOSFET amplifier circuit An appropriate DC operating
More informationElectronic Circuits for Mechatronics ELCT 609 Lecture 7: MOS-FET Amplifiers
Electronic Circuits for Mechatronics ELCT 609 Lecture 7: MOS-FET Amplifiers Assistant Professor Office: C3.315 E-mail: eman.azab@guc.edu.eg 1 Enhancement N-MOS Modes of Operation Mode V GS I DS V DS Cutoff
More informationECE315 / ECE515 Lecture 5 Date:
Lecture 5 ate: 20.08.2015 MOSFET Small Signal Models, and Analysis Common Source Amplifier Introduction MOSFET Small Signal Model To determine the small-signal performance of a given MOSFET amplifier circuit,
More informationLecture 11 Digital Circuits (I) THE INVERTER
Lecture 11 Digital Circuits (I) THE INVERTER Outline Introduction to digital circuits The inverter NMOS inverter with resistor pull-up Reading Assignment: Howe and Sodini; Chapter 5, Sections 5.1-5.3 6.12
More informationEE 330 Lecture 20. Operating Points for Amplifier Applications Amplification with Transistor Circuits Small Signal Modelling
EE 330 Lecture 20 Operating Points for Amplifier Applications Amplification with Transistor Circuits Small Signal Modelling Review from Last Lecture Simplified Multi-Region Model Alternate equivalent model
More informationReview Sheet for Midterm #2
Review Sheet for Midterm #2 Brian Bircumshaw brianb@eecs.berkeley.edu 1 Miterm #1 Review See Table 1 on the following page for a list of the most important equations you should know from Midterm #1. 2
More informationWeek 12: Output Stages, Frequency Response
ELE 2110A Electronic Circuits Week 12: Output Stages, Frequency esponse (2 hours only) Lecture 12-1 Output Stages Topics to cover Amplifier Frequency esponse eading Assignment: Chap 15.3, 16.1 of Jaeger
More informationECE315 / ECE515 Lecture 7 Date:
Lecture 7 ate: 01.09.2016 CG Amplifier Examples Biasing in MOS Amplifier Circuits Common Gate (CG) Amplifier CG Amplifier- nput is applied at the Source and the output is sensed at the rain. The Gate terminal
More informationElectronic Circuits EE359A
Electronic Circuits EE359A Bruce McNair B206 bmcnair@stevens.edu 201-216-5549 Lecture 12 1 MOSFET vs. BJT current-voltage characteristic 1.5 10 3 i C ( v) i D ( v) 1 10 3 500 0 2 4 6 8 10 v The drain current
More informationIntegrated Circuit Amplifiers. Comparison of MOSFETs and BJTs
Integrated Circuit Amplifiers Comparison of MOSFETs and BJTs 17 Typical CMOS Device Parameters 0.8 µm 0.25 µm 0.13 µm Parameter NMOS PMOS NMOS PMOS NMOS PMOS t ox (nm) 15 15 6 6 2.7 2.7 C ox (ff/µm 2 )
More informationLecture 13 - Digital Circuits (II) MOS Inverter Circuits. October 25, 2005
6.12 - Microelectronic Devices and Circuits - Fall 25 Lecture 13-1 Lecture 13 - Digital Circuits (II) MOS Inverter Circuits October 25, 25 Contents: 1. NMOS inverter with resistor pull-up (cont.) 2. NMOS
More informationAnalysis and Design of Analog Integrated Circuits Lecture 8. Cascode Techniques
Analysis and Design of Analog Integrated Circuits Lecture 8 Cascode Techniques Michael H. Perrott February 15, 2012 Copyright 2012 by Michael H. Perrott All rights reserved. Review of Large Signal Analysis
More informationLecture 26 Differential Amplifiers (I) DIFFERENTIAL AMPLIFIERS
Lecture 6 Differential Amplifiers (I) DIFFERENTIAL AMPLIFIERS Outline 1. Introduction. Incremental analysis of differential amplifier 3. Common-source differential amplifier Reading Assignment: Howe and
More informationLecture 13 - Digital Circuits (II) MOS Inverter Circuits. March 22, 2001
6.12 - Microelectronic Devices and Circuits - Spring 21 Lecture 13-1 Lecture 13 - Digital Circuits (II) MOS Inverter Circuits March 22, 21 Contents: 1. NMOS inverter with resistor pull-up (cont.) 2. NMOS
More informationECE315 / ECE515 Lecture 8 Date:
ECE35 / ECE55 Lecture 8 Date: 05.09.06 CS Amplifier with Constant Current Source Current Steering Circuits CS Stage Followed by CG Stage Cascode as Current Source Cascode as Amplifier ECE35 / ECE55 CS
More informationECE315 / ECE515 Lecture 9 Date:
Lecture 9 Date: 03.09.2015 Biasing in MOS Amplifier Circuits Biasing using Single Power Supply The general form of a single-supply MOSFET amplifier biasing circuit is: We typically attempt to satisfy three
More informationSession 2 MOS Transistor for RF Circuits
Session 2 MOS Transistor for RF Circuits Session Speaker Chandramohan P. Session Contents MOS transistor basics MOS equivalent circuit Single stage amplifiers Opamp design Session objectives To understand
More informationDC Coupling: General Trends
DC Coupling: General Trends * Goal: want both input and output to be centered at halfway between the positive and negative supplies (or ground, for a single supply) -- in order to have maximum possible
More informationChapter 7 Building Blocks of Integrated Circuit Amplifiers: Part D: Advanced Current Mirrors
1 Chapter 7 Building Blocks of Integrated Circuit Amplifiers: Part D: Advanced Current Mirrors Current Mirror Example 2 Two Stage Op Amp (MOSFET) Current Mirror Example Three Stage 741 Opamp (BJT) 3 4
More informationECE 2C Final Exam. June 8, 2010
ECE 2C Final Exam June 8, 2010 Do not open exam until instructed to. Closed book: Crib sheet and 2 pages personal notes permitted There are 4 problems on this exam, and you have 3 hours. Use any and all
More informationBJT Amplifier. Superposition principle (linear amplifier)
BJT Amplifier Two types analysis DC analysis Applied DC voltage source AC analysis Time varying signal source Superposition principle (linear amplifier) The response of a linear amplifier circuit excited
More informationEE 330 Laboratory 8 Discrete Semiconductor Amplifiers
EE 330 Laboratory 8 Discrete Semiconductor Amplifiers Fall 2017 Contents Objective:... 2 Discussion:... 2 Components Needed:... 2 Part 1 Voltage Controlled Amplifier... 2 Part 2 Common Source Amplifier...
More informationMOSFET Amplifier Configuration. MOSFET Amplifier Configuration
MOSFET Amplifier Configuration Single stage The signal is fed to the amplifier represented as sig with an internal resistance sig. MOSFET is represented by its small signal model. Generally interested
More informationField Effect Transistors
Field Effect Transistors LECTURE NO. - 41 Field Effect Transistors www.mycsvtunotes.in JFET MOSFET CMOS Field Effect transistors - FETs First, why are we using still another transistor? BJTs had a small
More informationLaboratory 1 Single-Stage MOSFET Amplifier Analysis and Design Due Date: Week of February 20, 2014, at the beginning of your lab section
Laboratory 1 Single-Stage MOSFET Amplifier Analysis and Design Due Date: Week of February 20, 2014, at the beginning of your lab section Objective To analyze and design single-stage common source amplifiers.
More informationECE 340 Lecture 40 : MOSFET I
ECE 340 Lecture 40 : MOSFET I Class Outline: MOS Capacitance-Voltage Analysis MOSFET - Output Characteristics MOSFET - Transfer Characteristics Things you should know when you leave Key Questions How do
More informationEE 330 Lecture 26. Amplifier Biasing (precursor) Two-Port Amplifier Model
EE 330 Lecture 26 Amplifier Biasing (precursor) Two-Port Amplifier Model Exam Schedule Exam 2 Friday October 27 Exam 3 Friday November 17 Review from Last Lecture Graphical Analysis and Interpretation
More informationMicroelectronic Devices and Circuits- EECS105 Final Exam
EECS105 1 of 13 Fall 2000 Microelectronic Devices and Circuits- EECS105 Final Exam Wednesday, December 13, 2000 Costas J. Spanos University of California at Berkeley College of Engineering Department of
More information6.002 Circuits and Electronics Final Exam Practice Set 1
MASSACHUSETTS INSTITUTE OF TECHNOLOGY DEPARTMENT OF ELECTRICAL ENGINEERING AND COMPUTER SCIENCE 6.002 Circuits and Electronics Set 1 Problem 1 Figure 1 shows a simplified small-signal model of a certain
More informationV o. ECE2280 Homework #1 Fall Use: ignore r o, V BE =0.7, β=100 V I = sin(20t) For DC analysis, assume that the capacitors are open
ECE2280 Homework #1 Fall 2011 1. Use: ignore r o, V BE =0.7, β=100 V I = 200.001sin(20t) For DC analysis, assume that the capacitors are open (a) Solve for the DC currents: a. I B b. I E c. I C (b) Solve
More informationCurrent Supply Topology. CMOS Cascode Transconductance Amplifier. Basic topology. p-channel cascode current supply is an obvious solution
CMOS Cascode Transconductance Amplifier Basic topology. Current Supply Topology p-channel cascode current supply is an obvious solution Current supply must have a very high source resistance r oc since
More informationENEE 307 Laboratory#2 (n-mosfet, p-mosfet, and a single n-mosfet amplifier in the common source configuration)
Revised 2/16/2007 ENEE 307 Laboratory#2 (n-mosfet, p-mosfet, and a single n-mosfet amplifier in the common source configuration) *NOTE: The text mentioned below refers to the Sedra/Smith, 5th edition.
More informationEE105 Fall 2015 Microelectronic Devices and Circuits
EE105 Fall 2015 Microelectronic Devices and Circuits Multi-Stage Amplifiers Prof. Ming C. Wu wu@eecs.berkeley.edu 511 Sutardja Dai Hall (SDH) Terminal Gain and I/O Resistances of MOS Amplifiers Common
More informationMicroelectronics Circuit Analysis and Design
Neamen Microelectronics Chapter 4-1 Microelectronics Circuit Analysis and Design Donald A. Neamen Chapter 4 Basic FET Amplifiers Neamen Microelectronics Chapter 4-2 In this chapter, we will: Investigate
More information6.976 High Speed Communication Circuits and Systems Lecture 5 High Speed, Broadband Amplifiers
6.976 High Speed Communication Circuits and Systems Lecture 5 High Speed, Broadband Amplifiers Michael Perrott Massachusetts Institute of Technology Copyright 2003 by Michael H. Perrott Broadband Communication
More informationCOLLECTOR DRAIN BASE GATE EMITTER. Applying a voltage to the Gate connection allows current to flow between the Drain and Source connections.
MOSFETS Although the base current in a transistor is usually small (< 0.1 ma), some input devices (e.g. a crystal microphone) may be limited in their output. In order to overcome this, a Field Effect Transistor
More informationEE 230 Fall 2006 Experiment 11. Small Signal Linear Operation of Nonlinear Devices
EE 230 Fall 2006 Experiment 11 Small Signal Linear Operation of Nonlinear Devices Purpose: The purpose of this laboratory experiment is to investigate the use of small signal concepts for designing and
More informationEECS3611 Analog Integrated Circuit Design. Lecture 3. Current Source and Current Mirror
EECS3611 Analog ntegrated Circuit Design Lecture 3 Current Source and Current Mirror ntroduction Before any device can be used in any application, it has to be properly biased so that small signal AC parameters
More informationECE 442 Solid State Devices & Circuits. 15. Differential Amplifiers
ECE 442 Solid State Devices & Circuits 15. Differential Amplifiers Jose E. Schutt-Aine Electrical & Computer Engineering University of Illinois jschutt@emlab.uiuc.edu ECE 442 Jose Schutt Aine 1 Background
More informationA Low Power Low Voltage High Performance CMOS Current Mirror
RESEARCH ARTICLE OPEN ACCESS A Low Power Low Voltage High Performance CMOS Current Mirror Sirish Rao, Sampath Kumar V Department of Electronics & Communication JSS Academy of Technical Education Noida,
More informationECE 546 Lecture 12 Integrated Circuits
ECE 546 Lecture 12 Integrated Circuits Spring 2018 Jose E. Schutt-Aine Electrical & Computer Engineering University of Illinois jesa@illinois.edu ECE 546 Jose Schutt Aine 1 Integrated Circuits IC Requirements
More informationBasic Electronics Prof. Dr. Chitralekha Mahanta Department of Electronics and Communication Engineering Indian Institute of Technology, Guwahati
Basic Electronics Prof. Dr. Chitralekha Mahanta Department of Electronics and Communication Engineering Indian Institute of Technology, Guwahati Module: 3 Field Effect Transistors Lecture-8 Junction Field
More informationLecture 33: Context. Prof. J. S. Smith
Lecture 33: Prof J. S. Smith Context We are continuing to review some of the building blocks for multi-stage amplifiers, including current sources and cascode connected devices, and we will also look at
More informationLecture 16: MOS Transistor models: Linear models, SPICE models. Context. In the last lecture, we discussed the MOS transistor, and
Lecture 16: MOS Transistor models: Linear models, SPICE models Context In the last lecture, we discussed the MOS transistor, and added a correction due to the changing depletion region, called the body
More informationGechstudentszone.wordpress.com
UNIT 4: Small Signal Analysis of Amplifiers 4.1 Basic FET Amplifiers In the last chapter, we described the operation of the FET, in particular the MOSFET, and analyzed and designed the dc response of circuits
More informationDifferential Amplifiers. EE105 - Spring 2007 Microelectronic Devices and Circuits. Audio Amplifier Example. Small-Signal Model for Bipolar Transistor
EE105 - Spring 007 Microelectronic Devices and Circuits Lecture 8 Differential Amplifiers Differential Amplifiers General Considerations MOS Differential Pair Cascode Differential Amplifiers Common-Mode
More informationRadivoje Đurić, 2015, Analogna Integrisana Kola 1
Low power OTA 1 Two-Stage, Miller Op Amp Operating in Weak Inversion Low frequency response: gm1 gm6 Av 0 g g g g A v 0 ds2 ds4 ds6 ds7 I D m, ds D nvt g g I n GB and SR: GB 1 1 n 1 2 4 6 6 7 g 2 2 m1
More informationECE 255, MOSFET Basic Configurations
ECE 255, MOSFET Basic Configurations 8 March 2018 In this lecture, we will go back to Section 7.3, and the basic configurations of MOSFET amplifiers will be studied similar to that of BJT. Previously,
More informationUNIT-1 Bipolar Junction Transistors. Text Book:, Microelectronic Circuits 6 ed., by Sedra and Smith, Oxford Press
UNIT-1 Bipolar Junction Transistors Text Book:, Microelectronic Circuits 6 ed., by Sedra and Smith, Oxford Press Figure 6.1 A simplified structure of the npn transistor. Microelectronic Circuits, Sixth
More informationThe Miller Approximation. CE Frequency Response. The exact analysis is worked out on pp of H&S.
CE Frequency Response The exact analysis is worked out on pp. 639-64 of H&S. The Miller Approximation Therefore, we consider the effect of C µ on the input node only V ---------- out V s = r g π m ------------------
More informationA Basis for LDO and It s Thermal Design
A Basis for LDO and It s Thermal Design Introduction The AIC LDO family device, a 3-terminal regulator, can be easily used with all protection features that are expected in high performance voltage regulation
More informationMicroelectronic Circuits II. Ch 10 : Operational-Amplifier Circuits
Microelectronic Circuits II Ch 0 : Operational-Amplifier Circuits 0. The Two-stage CMOS Op Amp 0.2 The Folded-Cascode CMOS Op Amp CNU EE 0.- Operational-Amplifier Introduction - Analog ICs : operational
More informationThe George Washington University School of Engineering and Applied Science Department of Electrical and Computer Engineering ECE 20 - LAB
The George Washington University School of Engineering and Applied Science Department of Electrical and Computer Engineering ECE 20 - LAB Experiment # 11 MOSFET Amplifiers testing and designing Equipment:
More informationLecture 11 Circuits numériques (I) L'inverseur
Lecture 11 Circuits numériques (I) L'inverseur Outline Introduction to digital circuits The inverter NMOS inverter with resistor pull-up 6.12 Spring 24 Lecture 11 1 1. Introduction to digital circuits:
More informationUnit 6 - Op-Amp Applications
X reviewer2@nptel.iitm.ac.in Courses» Integrated Circuits, MOSFETs, OP-Amps and their Unit 6 - Announcements Course Ask a Question Progress Mentor Course outline Introduction to IC Technology Introduction
More informationSolid State Devices & Circuits. 18. Advanced Techniques
ECE 442 Solid State Devices & Circuits 18. Advanced Techniques Jose E. Schutt-Aine Electrical l&c Computer Engineering i University of Illinois jschutt@emlab.uiuc.edu 1 Darlington Configuration - Popular
More informationOperational Amplifiers
CHAPTER 9 Operational Amplifiers Analog IC Analysis and Design 9- Chih-Cheng Hsieh Outline. General Consideration. One-Stage Op Amps / Two-Stage Op Amps 3. Gain Boosting 4. Common-Mode Feedback 5. Input
More informationUNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering EXPERIMENT 8 MOSFET AMPLIFIER CONFIGURATIONS AND INPUT/OUTPUT IMPEDANCE OBJECTIVES The purpose of this experiment
More informationDigital Electronics. Assign 1 and 0 to a range of voltage (or current), with a separation that minimizes a transition region. Positive Logic.
Digital Electronics Assign 1 and 0 to a range of voltage (or current), with a separation that minimizes a transition region Positive Logic Logic 1 Negative Logic Logic 0 Voltage Transition Region Transition
More informationElectronic Devices. Floyd. Chapter 9. Ninth Edition. Electronic Devices, 9th edition Thomas L. Floyd
Electronic Devices Ninth Edition Floyd Chapter 9 The Common-Source Amplifier In a CS amplifier, the input signal is applied to the gate and the output signal is taken from the drain. The amplifier has
More informationChapter 8. Field Effect Transistor
Chapter 8. Field Effect Transistor Field Effect Transistor: The field effect transistor is a semiconductor device, which depends for its operation on the control of current by an electric field. There
More informationExperiment 1: Amplifier Characterization Spring 2019
Experiment 1: Amplifier Characterization Spring 2019 Objective: The objective of this experiment is to develop methods for characterizing key properties of operational amplifiers Note: We will be using
More informationELEC 350L Electronics I Laboratory Fall 2012
ELEC 350L Electronics I Laboratory Fall 2012 Lab #9: NMOS and CMOS Inverter Circuits Introduction The inverter, or NOT gate, is the fundamental building block of most digital devices. The circuits used
More informationReading. Lecture 33: Context. Lecture Outline. Chapter 9, multi-stage amplifiers. Prof. J. S. Smith
eading Lecture 33: Chapter 9, multi-stage amplifiers Prof J. S. Smith Context Lecture Outline We are continuing to review some of the building blocks for multi-stage amplifiers, including current sources
More informationUNIVERSITY OF NORTH CAROLINA AT CHARLOTTE. Department of Electrical and Computer Engineering
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering Experiment No. 9 - MOSFET Amplifier Configurations Overview: The purpose of this experiment is to familiarize
More informationLOW-VOLTAGE, CLASS AB AND HIGH SLEW-RATE TWO STAGE OPERATIONAL AMPLIFIERS. CARLOS FERNANDO NIEVA-LOZANO, B.Sc.E.E
LOW-VOLTAGE, CLASS AB AND HIGH SLEW-RATE TWO STAGE OPERATIONAL AMPLIFIERS BY CARLOS FERNANDO NIEVA-LOZANO, B.Sc.E.E A thesis submitted to the Graduate School in partial fulfillment of the requirements
More informationAnalog Integrated Circuit Design Exercise 1
Analog Integrated Circuit Design Exercise 1 Integrated Electronic Systems Lab Prof. Dr.-Ing. Klaus Hofmann M.Sc. Katrin Hirmer, M.Sc. Sreekesh Lakshminarayanan Status: 21.10.2015 Pre-Assignments The lecture
More informationLecture 030 ECE4430 Review III (1/9/04) Page 030-1
Lecture 030 ECE4430 Review III (1/9/04) Page 0301 LECTURE 030 ECE 4430 REVIEW III (READING: GHLM Chaps. 3 and 4) Objective The objective of this presentation is: 1.) Identify the prerequisite material
More informationUnit 5 - Operational Amplifiers
X reviewer2@nptel.iitm.ac.in Courses» Integrated Circuits, MOSFETs, OP-Amps and their Unit 5 - Amplifiers Announcements Course Ask a Question Progress Mentor Course outline Introduction to IC Technology
More informationLecture 3 Switched-Capacitor Circuits Trevor Caldwell
Advanced Analog Circuits Lecture 3 Switched-Capacitor Circuits Trevor Caldwell trevor.caldwell@analog.com Lecture Plan Date Lecture (Wednesday 2-4pm) Reference Homework 2017-01-11 1 MOD1 & MOD2 ST 2, 3,
More informationApplied Electronics II
Applied Electronics II Chapter 2: Differential Amplifier School of Electrical and Computer Engineering Addis Ababa Institute of Technology Addis Ababa University Daniel D./Abel G. April 4, 2016 Chapter
More informationEE 435. Lecture 6: Current Mirrors Signal Swing
EE 435 ecture 6: Current Mirrors Signal Swing 1 Review from last lecture: Where we are at: Basic Op Amp Design Fundamental Amplifier Design Issues Single-Stage ow Gain Op Amps Single-Stage High Gain Op
More informationChapter 5. Operational Amplifiers and Source Followers. 5.1 Operational Amplifier
Chapter 5 Operational Amplifiers and Source Followers 5.1 Operational Amplifier In single ended operation the output is measured with respect to a fixed potential, usually ground, whereas in double-ended
More informationCHAPTER 4 ULTRA WIDE BAND LOW NOISE AMPLIFIER DESIGN
93 CHAPTER 4 ULTRA WIDE BAND LOW NOISE AMPLIFIER DESIGN 4.1 INTRODUCTION Ultra Wide Band (UWB) system is capable of transmitting data over a wide spectrum of frequency bands with low power and high data
More informationCourse Outline. 4. Chapter 5: MOS Field Effect Transistors (MOSFET) 5. Chapter 6: Bipolar Junction Transistors (BJT)
Course Outline 1. Chapter 1: Signals and Amplifiers 1 2. Chapter 3: Semiconductors 3. Chapter 4: Diodes 4. Chapter 5: MOS Field Effect Transistors (MOSFET) 5. Chapter 6: Bipolar Junction Transistors (BJT)
More informationElectronic Devices and Circuits Lecture 20 - Linear Amp. Analysis and Design I - Outline Announcements. )/2 [v IN1.
6.012 Electronic Devices and Circuits Lecture 20 Linear Amp. Analysis and Design I Outline Announcements Handouts Lecture Outline and Summary Announcements Design Problem due in under two weeks Review
More informationD n ox GS THN DS GS THN DS GS THN. D n ox GS THN DS GS THN DS GS THN
Name: EXAM #3 Closed book, closed notes. Calculators may be used for numeric computations only. All work is to be your own - show your work for maximum partial credit. Data: Use the following data in all
More informationECE 255, MOSFET Amplifiers
ECE 255, MOSFET Amplifiers 26 October 2017 In this lecture, the basic configurations of MOSFET amplifiers will be studied similar to that of BJT. Previously, it has been shown that with the transistor
More informationSKEL 4283 Analog CMOS IC Design Current Mirrors
SKEL 4283 Analog CMOS IC Design Current Mirrors Dr. Nasir Shaikh Husin Faculty of Electrical Engineering Universiti Teknologi Malaysia Current Mirrors 1 Objectives Introduce and characterize the current
More informationChapter 8 Differential and Multistage Amplifiers
1 Chapter 8 Differential and Multistage Amplifiers Operational Amplifier Circuit Components 2 1. Ch 7: Current Mirrors and Biasing 2. Ch 9: Frequency Response 3. Ch 8: Active-Loaded Differential Pair 4.
More informationMicroelectronics Part 2: Basic analog CMOS circuits
GBM830 Dispositifs Médicaux Intelligents Microelectronics Part : Basic analog CMOS circuits Mohamad Sawan et al. Laboratoire de neurotechnologies Polystim!! http://www.cours.polymtl.ca/gbm830/! mohamad.sawan@polymtl.ca!
More informationANALOG FUNDAMENTALS C. Topic 4 BASIC FET AMPLIFIER CONFIGURATIONS
AV18-AFC ANALOG FUNDAMENTALS C Topic 4 BASIC FET AMPLIFIER CONFIGURATIONS 1 ANALOG FUNDAMENTALS C AV18-AFC Overview This topic identifies the basic FET amplifier configurations and their principles of
More informationEE 140 / EE 240A ANALOG INTEGRATED CIRCUITS FALL 2015 C. Nguyen PROBLEM SET #7
Issued: Friday, Oct. 16, 2015 PROBLEM SET #7 Due (at 8 a.m.): Monday, Oct. 26, 2015, in the EE 140/240A HW box near 125 Cory. 1. A design error has resulted in a mismatch in the circuit of Fig. PS7-1.
More information