Guided Propagation Along the Optical Fiber. Xavier Fernando Ryerson University
|
|
- Ursula Joseph
- 5 years ago
- Views:
Transcription
1 Guided Propagation Along the Optical Fiber Xavier Fernando Ryerson University
2 The Nature of Light Quantum Theory Light consists of small particles (photons) Wave Theory Light travels as a transverse electromagnetic wave Ray Theory Light travels along a straight line and obeys laws of geometrical optics. Ray theory is valid when the objects are much larger than the wavelength (multimode fibers)
3 Refraction and reflection Snell s Law: n 1 Sin Φ 1 = n 2 Sin Φ 2 Critical Angle: Sin Φc=n 2 /n 1
4 Step Index Fiber n 1 n 2 n 1 >n 2 Core and Cladding are glass with appropriate optical properties while buffer is plastic for mechanical protection
5 Step Index Fiber y y Cladding Core φ r z Fiber axis n 2 n 1 n The step index optical fiber. The central region, the core, has greater refractiv index than the outer region, the cladding. The fiber has cylindrical symmetry use the coordinates r, φ, z to represent any point in the fiber. Cladding is normally much thicker than shown S.O. Kasap, Optoelectronics (Prentice Hall)
6 Meridian Ray Representation = n 2 n n 2 1 n 2 n 2 1
7 Total Internal Reflection α < α max A B α > α max n 2 n 0 n 1 Lost B θ < θ c θ > θ c Fiber axis Cladding Propagates A Core Maximum acceptance angle α max is that which just gives total internal reflection at the core-cladding interface, i.e. when α = α max then θ = θ c. Rays with α > α max (e.g. ray B) become refracted and penetrate the cladding and ar eventually lost S.O. Kasap, Optoelectronics (Prentice Hall)
8 Graded Index Fiber O 2 1 B θ B θ B' c/n a c/n b B' θ B' Ray 2 A θ A M Ray 1 B'' n c n b n a c b a O' We can visualize a graded inde fiber by imagining a stratified medium with the layers of refr indices n a > n b > n c... Consider tw close rays 1 and 2 launched Ofro at the same time but with sligh different launching angles. Ray just suffers total internal reflec Ray 2 becomes refracted B and at reflected at B' S.O. Kasap, Optoelectronics (Prentice Hall)
9 Single Mode Step Index Fiber r Buffer tube: d = 1mm n n 1 n 2 Protective polymerinc coating Cladding: d = µm Core: d = 8-10 µm The cross section of a typical single-mode fiber with a tight buffer tube. (d = diameter) 1999 S.O. Kasap, Optoelectronics (Prentice Hall)
10 Fiber Key Parameters
11 Comparison of fiber structures
12 Fiber Key Parameters
13 Step and Graded Index Fibers n 2 O n 1 n (a) Multimode step index fiber. Ray paths are different so that rays arrive at different times. O O' O'' n 2 n 1 n (b) Graded index fiber. Ray paths are different but so are the velocities along the paths so that all the rays arrive at the same time. n S.O. Kasap, Optoelectronics (Prentice Hall)
14 Total Internal Reflection (a) TIR (b) TIR n decreases step by step from one layer to next upper layer; very thin layers. Continuous decrease in n gives a ray path changing continuously. (a) A ray in thinly stratifed medium becomes refracted as it passes from one layer to the next upper layer with lower n and eventually its angle satisfies TIR (b) In a medium where n decreases continuously the path of the ray bends continuously S.O. Kasap, Optoelectronics (Prentice Hall)
15 Skew Rays Along the fiber 1 Meridional ray Fiber axis 3 1, 3 (a) A meridiona ray always crosses the fibe axis Fiber axis 3 Skew ray (b) A skew ray does not have to cross the fiber axis. It zigzags around the fiber axis. Ray path along the fiber Ray path projected on to a plane normal to fiber axis Illustration of the difference between a meridional ray and a skew ray. Numbers represent reflections of the ray S.O. Kasap, Optoelectronics (Prentice Hall)
16 Skew rays Skew rays circulate around the core and increase the dispersion
17 Polarizations of fundamental mode Two polarization states exist in the fundamental mode in a single mode fiber
18 Polarization Mode Dispersion (PMD) Each polarization state has a different velocity PMD
19 Major Dispersions in Fiber Modal Dispersion: Different modes travel at different velocities, exist only in multimodal conditions Waveguide Dispersion: Signal in the cladding travel with a different velocity than the signal in the core, significant in single mode conditions Material Dispersion: Refractive index n is a function of wavelength, exists in all fibers, function of the source line width
20 Effects of Dispersion and Attenuation
21 Dispersion for Digital Signals Fiber Information Digital signal Emitter t Input Photodetector Information Output Input Intensity Output Intensity ² τ 1/2 Very short light pulses 0 T t 0 t ~2² τ 1/2 An optical fiber link for transmitting digital information and the effect of dispersion in the fiber on the output pulses S.O. Kasap, Optoelectronics (Prentice Hall)
22 Modal Dispersion High order mode Low order mode Light pulse Cladding Broadened light pulse Intensity Core Intensity Axial Spread, τ 0 t t Schematic illustration of light propagation in a slab dielectric waveguide. Light pulse entering the waveguide breaks up into various modes which then propagate at different group velocities down the guide. At the end of the guide, the modes combine to constitute the output light pulse which is broader than the input light pulse S.O. Kasap, Optoelectronics (Prentice Hall)
23 Field Distribution in the Fiber Field of evanescent wave (exponential decay) y n 2 Field of guided wave E(y) m = 0 E(y,z,t) = E(y)cos(ωt β 0 z) Light n 1 n 2 The electric field pattern of the lowest mode traveling wave along the guide. This mode has m = 0 and the lowest θ. It is often referred to as the glazing incidence ray. It has the highest phase velocity along the guide S.O. Kasap, Optoelectronics (Prentice Hall)
24 Higher order modes Larger MFD y n 2 Cladding E(y) m = 0 m = 1 m = 2 Core 2a n 1 n 2 Cladding The electric field patterns of the first three modes m = ( 0, 1, 2) traveling wave along the guide. Notice different extents of fie penetration into the cladding S.O. Kasap, Optoelectronics (Prentice Hall)
25 Mode-field Diameter (2W 0 ) In a Single Mode Fiber, E( r) = 2 E0 exp( r / w 2 0 ) At r = w o, E(W o )=E o /e Typically W o > a
26 Power in the cladding Lower order modes have higher power in the cladding.
27 Higher the Wavelength More the Evanescent Field y Cladding y λ 1 > λ c λ 2 > λ 1 v g1 Core v g2 > v g1 ω 1 < ω cut-off ω 2 < ω 1 E(y) Cladding The electric field of TE 0 mode extends more into the cladding as the wavelength increases. As more of the field is carried by the cladding, the group velocity increases S.O. Kasap, Optoelectronics (Prentice Hall)
28 Mode-field diameter Vs wavelength
29 (a) The electric field of the fundamental mode (b) The intensity in the fundamental mode LP 01 (c) The intensity in LP 11 (d) The intensity in LP 21 Core Cladding E E 01 r The electric field distribution of the fundamental mod in the transverse plane to the fiber axis z. The light intensity is greatest at the center of the fiber. Intensity patterns in LP 01, LP 11 and LP 21 modes S.O. Kasap, Optoelectronics (Prentice Hall)
30 Cladding Power Vs Normalized Frequency
31 b LP 01 LP 11 LP 21 LP V Normalized propagation constant b vs. V-number for a step index fiber for various LP modes.
32 1.5 V[d 2 (Vb)/dV 2 ] V - number [d2(vb)/dv2] vs. V-number for a step index fiber (after W.A. Gambling et al., The Radio and Electronics Engineer, 51, 313, 1981) 1999 S.O. Kasap, Optoelectronics (Prentice Hall)
33 Input Emitter Very short light pulse v g (λ 1 ) v g (λ 2 ) Cladding Core Output Intensity Intensity Intensity Spectrum, ² λ Spread, ² τ λ λ λ 1 o 2 λ 0 t τ t All excitation sources are inherently non-monochromatic and emit within a spectrum, ² λ, of wavelengths. Waves in the guide with different free space wavelengths travel at different group velocities due to the wavelength dependence of n 1. The waves arrive at the end of the fiber at different times and hence result in a broadened output pulse S.O. Kasap, Optoelectronics (Prentice Hall) Material Dispersion
34 Material Dispersion Zero Dispersion Wavelength
35 Modifying Chromatic Dispersion Chromatic Dispersion = Material dispersion + Waveguide dispersion Material dispersion depends on the material properties and difficult to alter Waveguide dispersion can be altered by changing the fiber refractive index profile 1300 nm optimized Dispersion Shifting (to 1550 nm) Dispersion Flattening (from 1300 to 1550 nm)
36 Different Index Profiles 1300 nm optimized Dispersion Shifted
37 Different Index Profiles Dispersion Flattened Large area dispersion shifted Large area dispersion flattened
38 Different dispersion profiles
39 Dispersion Shifting/Flattening
40 Dispersion coefficient (ps km -1 nm -1 ) 30 n D m r 0-10 λ 1 λ 2 D ch = D m + D w D w λ (µm) Thin layer of cladding with a depressed index Dispersion flattened fiber example. The material dispersion coefficient (D m ) for the core material and waveguide dispersion coefficient (D w ) for the doubly clad fiber result in a flattened small chromatic dispersion between λ 1 and λ 2.
41 Zero Dispersion Wavelength Dispersion coefficient (ps km -1 nm -1 ) Dm Dm + D w λ 0 D w λ (µ m) Material dispersion coefficient (D m ) for the core material (taken as SiO 2 ), waveguide dispersion coefficient (D w ) (a = 4.2 µ m) and the total or chromatic dispersion coefficient D ch (= D m + D w ) as a function of free space wavelength, λ.
42 Dispersion coefficient (ps km -1 nm -1 ) 20 D m 10 SiO %GeO D w a (µm) λ (µm) Material and waveguide dispersion coefficients in an optical fiber with a core SiO %GeO 2 for a = 2.5 to 4 µm.
43 Total Dispersion For Single Mode Fibers: For Multi Mode Fibers: Group Velocity Dispersion If PMD is negligible
44 Dispersion & Attenuation Summary
45 Electrical signal (photocurrent) Fiber Sinusoidal signal Emitter t f = Modulation frequency Optical Input Optical Output Photodetector 1 khz 1 MHz 1 GHz f el Sinusoidal electrical signal f P i = Input light power 0 t P o = Output light power 0 t P o / P i khz 1 MHz 1 GHz f f op An optical fiber link for transmitting analog signals and the effect of dispersion in the fiber on the bandwidth, f op S.O. Kasap, Optoelectronics (Prentice Hall) Fiber Optic Link is a Low Pass Filter for Analog Signals
46 Attenuation Vs Frequency
47 Attenuation in Fiber Attenuation Coefficient α = P(0)dB P( z)db z db/km Silica has lowest attenuation at 1550 nm Water molecules resonate and give high attenuation around 1400 nm in standard fibers Attenuation happens because: Absorption (extrinsic and intrinsic) Scattering losses (Rayleigh, Raman and Brillouin ) Bending losses (macro and micro bending)
48 All Wave Fiber for DWDM Lowest attenuation occurs at 1550 nm for Silica
49 Attenuation characteristics
50 Bending Loss Field distribution θ θ Cladding Core θ θ > θ c θ Microbending θ < θ Escaping wave R Sharp bends change the local waveguide geometry that can lead to waves escaping. The zigzagging ray suddenly finds itself with an incidence angle θ that gives rise to either a transmitted wave, or to a greater cladding penetration; the field reaches the outside medium and some light energy is lost.
51 Power loss in a curved fiber Power in the evanescent field evaporates first
52 Bending-induced attenuation
53 Bending effects on loss Vs MFD
54 Micro-bending losses
55 Fiber Preform feed Production Thickness monitoring gauge Furnace 2000 C Polymer coater Ultraviolet light or furnace for curing Take-up drum Capstan Schematic illustration of a fiber drawing tower S.O. Kasap, Optoelectronics (Prentice Hall)
Guided Propagation Along the Optical Fiber. Xavier Fernando Ryerson Comm. Lab
Guided Propagation Along the Optical Fiber Xavier Fernando Ryerson Comm. Lab The Nature of Light Quantum Theory Light consists of small particles (photons) Wave Theory Light travels as a transverse electromagnetic
More informationGuided Propagation Along the Optical Fiber
Guided Propagation Along the Optical Fiber The Nature of Light Quantum Theory Light consists of small particles (photons) Wave Theory Light travels as a transverse electromagnetic wave Ray Theory Light
More informationDIELECTRIC WAVEGUIDES and OPTICAL FIBERS
DIELECTRIC WAVEGUIDES and OPTICAL FIBERS Light Light Light n 2 n 2 Light n 1 > n 2 A planar dielectric waveguide has a central rectangular region of higher refractive index n 1 than the surrounding region
More informationWaveguides and Optical Fibers
Waveguides and Optical Fibers Dielectric Waveguides Light Light Light n n Light n > n A planar dielectric waveguide has a central rectangular region of higher refractive index n than the surrounding region
More informationFiber Optic Communication Systems. Unit-05: Types of Fibers. https://sites.google.com/a/faculty.muet.edu.pk/abdullatif
Unit-05: Types of Fibers https://sites.google.com/a/faculty.muet.edu.pk/abdullatif Department of Telecommunication, MUET UET Jamshoro 1 Optical Fiber Department of Telecommunication, MUET UET Jamshoro
More informationLecture 10. Dielectric Waveguides and Optical Fibers
Lecture 10 Dielectric Waveguides and Optical Fibers Slab Waveguide, Modes, V-Number Modal, Material, and Waveguide Dispersions Step-Index Fiber, Multimode and Single Mode Fibers Numerical Aperture, Coupling
More informationUNIT-II : SIGNAL DEGRADATION IN OPTICAL FIBERS
UNIT-II : SIGNAL DEGRADATION IN OPTICAL FIBERS The Signal Transmitting through the fiber is degraded by two mechanisms. i) Attenuation ii) Dispersion Both are important to determine the transmission characteristics
More informationPhotonics and Optical Communication
Photonics and Optical Communication (Course Number 300352) Spring 2007 Dr. Dietmar Knipp Assistant Professor of Electrical Engineering http://www.faculty.iu-bremen.de/dknipp/ 1 Photonics and Optical Communication
More informationOptical Fiber Technology. Photonic Network By Dr. M H Zaidi
Optical Fiber Technology Numerical Aperture (NA) What is numerical aperture (NA)? Numerical aperture is the measure of the light gathering ability of optical fiber The higher the NA, the larger the core
More information1. Evolution Of Fiber Optic Systems
OPTICAL FIBER COMMUNICATION UNIT-I : OPTICAL FIBERS STRUCTURE: 1. Evolution Of Fiber Optic Systems The operating range of optical fiber system term and the characteristics of the four key components of
More informationFiber Optic Communications Communication Systems
INTRODUCTION TO FIBER-OPTIC COMMUNICATIONS A fiber-optic system is similar to the copper wire system in many respects. The difference is that fiber-optics use light pulses to transmit information down
More informationThe absorption of the light may be intrinsic or extrinsic
Attenuation Fiber Attenuation Types 1- Material Absorption losses 2- Intrinsic Absorption 3- Extrinsic Absorption 4- Scattering losses (Linear and nonlinear) 5- Bending Losses (Micro & Macro) Material
More informationSection B Lecture 5 FIBER CHARACTERISTICS
Section B Lecture 5 FIBER CHARACTERISTICS Material absorption Losses Material absorption is a loss mechanism related to material composition and fabrication process for the fiber. This results in dissipation
More informationSIGNAL DEGRADATION IN OPTICAL FIBERS
Volume Issue January 04, ISSN 348 8050 SIGNAL DEGRADATION IN OPTICAL FIBERS Gyan Prakash Pal, Manishankar Gupta,,, Assistant Professor, Electronics & Communication Engineering Department, Shanti Institute
More informationChapter 3 Signal Degradation in Optical Fibers
What about the loss in optical fiber? Why and to what degree do optical signals gets distorted as they propagate along a fiber? Fiber links are limited by in path length by attenuation and pulse distortion.
More informationIndustrial Automation
OPTICAL FIBER. SINGLEMODE OR MULTIMODE It is important to understand the differences between singlemode and multimode fiber optics before selecting one or the other at the start of a project. Its different
More informationUNIT List the requirements that be satisfied by materials used to manufacture optical fiber? ANS: Fiber Materials
UNIT- 2 1. List the requirements that be satisfied by materials used to manufacture optical fiber? ANS: Fiber Materials Most of the fibers are made up of glass consisting of either Silica (SiO 2 ) or.silicate.
More informationFiberoptic and Waveguide Sensors
Fiberoptic and Waveguide Sensors Wei-Chih Wang Department of Mecahnical Engineering University of Washington Optical sensors Advantages: -immune from electromagnetic field interference (EMI) - extreme
More information2. The Basic principle of optical fibre (Or) Working principle of optical fibre (or) Total internal reflection
Introduction Fibre optics deals with the light propagation through thin glass fibres. Fibre optics plays an important role in the field of communication to transmit voice, television and digital data signals
More informationEE 233. LIGHTWAVE. Chapter 2. Optical Fibers. Instructor: Ivan P. Kaminow
EE 233. LIGHTWAVE SYSTEMS Chapter 2. Optical Fibers Instructor: Ivan P. Kaminow PLANAR WAVEGUIDE (RAY PICTURE) Agrawal (2004) Kogelnik PLANAR WAVEGUIDE a = (n s 2 - n c2 )/ (n f 2 - n s2 ) = asymmetry;
More informationExamination Optoelectronic Communication Technology. April 11, Name: Student ID number: OCT1 1: OCT 2: OCT 3: OCT 4: Total: Grade:
Examination Optoelectronic Communication Technology April, 26 Name: Student ID number: OCT : OCT 2: OCT 3: OCT 4: Total: Grade: Declaration of Consent I hereby agree to have my exam results published on
More informationFIBER OPTICS. Prof. R.K. Shevgaonkar. Department of Electrical Engineering. Indian Institute of Technology, Bombay. Lecture: 4
FIBER OPTICS Prof. R.K. Shevgaonkar Department of Electrical Engineering Indian Institute of Technology, Bombay Lecture: 4 Modal Propagation of Light in an Optical Fiber Fiber Optics, Prof. R.K. Shevgaonkar,
More informationThere are lots of problems or challenges with fiber, Attenuation, Reflections, Dispersion and so on. So here we will look at these problems.
The Hard theory The Hard Theory An introduction to fiber, should also include a section with some of the difficult theory. So if everything else in the book was very easily understood, then this section
More informationOptical behavior. Reading assignment. Topic 10
Reading assignment Optical behavior Topic 10 Askeland and Phule, The Science and Engineering of Materials, 4 th Ed.,Ch. 0. Shackelford, Materials Science for Engineers, 6 th Ed., Ch. 16. Chung, Composite
More informationOptical systems have carrier frequencies of ~100 THz. This corresponds to wavelengths from µm.
Introduction A communication system transmits information form one place to another. This could be from one building to another or across the ocean(s). Many systems use an EM carrier wave to transmit information.
More informationτ mod = T modal = longest ray path shortest ray path n 1 L 1 = L n 2 1
S. Blair February 15, 2012 23 2.2. Pulse dispersion Pulse dispersion is the spreading of a pulse as it propagates down an optical fiber. Pulse spreading is an obvious detrimental effect that limits the
More informationTypes of losses in optical fiber cable are: Due to attenuation, the power of light wave decreases exponentially with distance.
UNIT-II TRANSMISSION CHARACTERISTICS OF OPTICAL FIBERS SIGNAL ATTENUATION: Signal attenuation in an optical fiber is defined as the decrease in light power during light propagation along an optical fiber.
More informationEC Optical Communication And Networking TWO MARKS QUESTION AND ANSWERS UNIT -1 INTRODUCTION
EC6702 - Optical Communication And Networking TWO MARKS QUESTION AND ANSWERS UNIT -1 INTRODUCTION Ray Theory Transmission 1. Write short notes on ray optics theory. Laws governing the nature of light are
More informationStudy of Optical Fiber Design Parameters in Fiber Optics Communications
Kurdistan Journal of Applied Research (KJAR) Print-ISSN: 2411-7684 Electronic-ISSN: 2411-7706 kjar.spu.edu.iq Volume 2 Issue 3 August 2017 DOI: 10.24017/science.2017.3.52 Study of Optical Fiber Design
More informationIndex of refraction varies significantly for broadband pulses
Index of refraction varies significantly for broadband pulses Δt=10 fs Δλ =90nm index of refraction may vary by nearly 1% phase speed depends on n v φ (λ) = c n(λ) n phase relations will be lost as pulse
More informationOptical Fiber. n 2. n 1. θ 2. θ 1. Critical Angle According to Snell s Law
ECE 271 Week 10 Critical Angle According to Snell s Law n 1 sin θ 1 = n 1 sin θ 2 θ 1 and θ 2 are angle of incidences The angle of incidence is measured with respect to the normal at the refractive boundary
More informationMultimode Optical Fiber
Multimode Optical Fiber 1 OBJECTIVE Determine the optical modes that exist for multimode step index fibers and investigate their performance on optical systems. 2 PRE-LAB The backbone of optical systems
More informationThe electric field for the wave sketched in Fig. 3-1 can be written as
ELECTROMAGNETIC WAVES Light consists of an electric field and a magnetic field that oscillate at very high rates, of the order of 10 14 Hz. These fields travel in wavelike fashion at very high speeds.
More informationLectureo5 FIBRE OPTICS. Unit-03
Lectureo5 FIBRE OPTICS Unit-03 INTRODUCTION FUNDAMENTAL IDEAS ABOUT OPTICAL FIBRE Multimode Fibres Multimode Step Index Fibres Multimode Graded Index Fibres INTRODUCTION In communication systems, there
More informationGeometrical Optics Fiber optics The eye
Phys 322 Lecture 16 Chapter 5 Geometrical Optics Fiber optics The eye First optical communication Alexander Graham Bell 1847-1922 1880: photophone 4 years after inventing a telephone! Fiberoptics: first
More informationChapter 18: Fiber Optic and Laser Technology
Chapter 18: Fiber Optic and Laser Technology Chapter 18 Objectives At the conclusion of this chapter, the reader will be able to: Describe the construction of fiber optic cable. Describe the propagation
More informationUNIT Write notes on broadening of pulse in the fiber dispersion?
UNIT 3 1. Write notes on broadening of pulse in the fiber dispersion? Ans: The dispersion of the transmitted optical signal causes distortion for both digital and analog transmission along optical fibers.
More informationDepartment of Electrical Engineering and Computer Science
MASSACHUSETTS INSTITUTE of TECHNOLOGY Department of Electrical Engineering and Computer Science 6.161/6637 Practice Quiz 2 Issued X:XXpm 4/XX/2004 Spring Term, 2004 Due X:XX+1:30pm 4/XX/2004 Please utilize
More informationPhotonics and Optical Communication Spring 2005
Photonics and Optical Communication Spring 2005 Final Exam Instructor: Dr. Dietmar Knipp, Assistant Professor of Electrical Engineering Name: Mat. -Nr.: Guidelines: Duration of the Final Exam: 2 hour You
More informationECSE 352: Electromagnetic Waves
December 2008 Final Examination ECSE 352: Electromagnetic Waves 09:00 12:00, December 15, 2008 Examiner: Zetian Mi Associate Examiner: Andrew Kirk Student Name: McGill ID: Instructions: This is a CLOSED
More informationOptical Communication Engineering (4041) B.Eng.
Optical Communication Engineering (4041) B.Eng. School of Electrical and Electronic Engineering The University of Adelaide, Australia Dr Bernd Fischer The Dream & The Reality Leadership is the ability
More informationMAHALAKSHMI ENGINEERING COLLEGE TIRUCHIRAPALLI
MAHALAKSHMI ENGINEERING COLLEGE TIRUCHIRAPALLI - 621213 DEPARTMENT : ECE SUBJECT NAME : OPTICAL COMMUNICATION & NETWORKS SUBJECT CODE : EC 2402 UNIT II: TRANSMISSION CHARACTERISTICS OF OPTICAL FIBERS PART
More informationUNIT I INTRODUCTION TO OPTICAL FIBERS
UNIT I INTRODUCTION TO OPTICAL FIBERS 9 Evolution of fiber optic system Element of an Optical Fiber Transmission link Total internal reflection Acceptance angle Numerical aperture Skew rays Ray Optics
More informationis a method of transmitting information from one place to another by sending light through an optical fiber. The light forms an electromagnetic
is a method of transmitting information from one place to another by sending light through an optical fiber. The light forms an electromagnetic carrier wave that is modulated to carry information. The
More informationPhotograph of the rectangular waveguide components
Waveguides Photograph of the rectangular waveguide components BACKGROUND A transmission line can be used to guide EM energy from one point (generator) to another (load). A transmission line can support
More informationFiber Optic Principles. Oct-09 1
Fiber Optic Principles Oct-09 1 Fiber Optic Basics Optical fiber Active components Attenuation Power budget Bandwidth Oct-09 2 Reference www.flukenetworks.com/fiber Handbook Fiber Optic Technologies (Vivec
More informationIndustrial Instrumentation Prof. A. Barua Department of Electrical Engineering Indian Institute of Technology, Kharagpur
Industrial Instrumentation Prof. A. Barua Department of Electrical Engineering Indian Institute of Technology, Kharagpur Lecture - 29 Optoelectronic Sensor-II (Refer Slide Time: 00:36) Welcome to lesson
More informationOPTICAL NETWORKS. Building Blocks. A. Gençata İTÜ, Dept. Computer Engineering 2005
OPTICAL NETWORKS Building Blocks A. Gençata İTÜ, Dept. Computer Engineering 2005 Introduction An introduction to WDM devices. optical fiber optical couplers optical receivers optical filters optical amplifiers
More informationLECTURE NOTES OPTICAL FIBER COMMUNICATION (15A04701) IV B. Tech I Semester (JNTUA-R15) Mrs. N.Pranavi, Assistant Professor
LECTURE NOTES ON OPTICAL FIBER COMMUNICATION (15A04701) 2018 2019 IV B. Tech I Semester (JNTUA-R15) Mrs. N.Pranavi, Assistant Professor CHADALAWADA RAMANAMMA ENGINEERING COLLEGE (AUTONOMOUS) Chadalawada
More informationSingle-photon excitation of morphology dependent resonance
Single-photon excitation of morphology dependent resonance 3.1 Introduction The examination of morphology dependent resonance (MDR) has been of considerable importance to many fields in optical science.
More informationSKP Engineering College
SKP Engineering College Tiruvannamalai 606611 A Course Material on Optical Communication and Networks By M.Mageshbabu Assistant Professor Electronics and Communication Engineering Department Electronics
More informationOptical Amplifiers Photonics and Integrated Optics (ELEC-E3240) Zhipei Sun Photonics Group Department of Micro- and Nanosciences Aalto University
Photonics Group Department of Micro- and Nanosciences Aalto University Optical Amplifiers Photonics and Integrated Optics (ELEC-E3240) Zhipei Sun Last Lecture Topics Course introduction Ray optics & optical
More informationJFOC-BSG2D MODEL:JFOC-BSG2D. optic.com. For detailed inquiry please contact our sales team at:
JFOC-BSG2D MODEL:JFOC-BSG2D For detailed inquiry please contact our sales team at: market@jfiber optic.com Description : JFOC-BSG2D dispersion unshifted singlemode fiber is designed specially for optical
More informationFundamentals of Electromagnetics With Engineering Applications by Stuart M. Wentworth Copyright 2005 by John Wiley & Sons. All rights reserved.
Figure 7-1 (p. 339) Non-TEM mmode waveguide structures include (a) rectangular waveguide, (b) circular waveguide., (c) dielectric slab waveguide, and (d) fiber optic waveguide. Figure 7-2 (p. 340) Cross
More informationChapter 9 GUIDED WAVE OPTICS
[Reading Assignment, Hecht 5.6] Chapter 9 GUIDED WAVE OPTICS Optical fibers The step index circular waveguide is the most common fiber design for optical communications plastic coating (sheath) core cladding
More informationSYLLABUS. Optical Fiber Communication
SYLLABUS Optical Fiber Communication Subject Code : IA Marks : 25 No. of Lecture Hrs/Week : 04 Exam Hours : 03 Total no. of Lecture Hrs. : 52 Exam Marks : 100 UNIT - 1 PART - A OVERVIEW OF OPTICAL FIBER
More informationLosses and Dispersion in Waveguides
Losses and Dispersion in Waveguides Wei-Chih WangInstitute of Nanoengineeirng and Microsystems National Tsing Hua University 1 Week 13 Course Website: http://courses.washington.edu/me557/sensors Reading
More informationCOM 46: ADVANCED COMMUNICATIONS jfm 07 FIBER OPTICS
FIBER OPTICS Fiber optics is a unique transmission medium. It has some unique advantages over conventional communication media, such as copper wire, microwave or coaxial cables. The major advantage is
More informationOptical fibre. Principle and applications
Optical fibre Principle and applications Circa 2500 B.C. Earliest known glass Roman times-glass drawn into fibers Venice Decorative Flowers made of glass fibers 1609-Galileo uses optical telescope 1626-Snell
More informationChapter 2: Fiber Optics as a communication medium
Chapter 2: Fiber Optics as a communication medium 2.1 Fiber Fabrication: Basically, fiber manufacturers use two methods to fabricate multimode and single mode glass fibers. One method is vapor phase oxidation,
More information2 in the multipath dispersion of the optical fibre. (b) Discuss the merits and drawbacks of cut bouls method of measurement of alternation.
B.TECH IV Year I Semester (R09) Regular Examinations, November 2012 1 (a) Derive an expression for multiple time difference tt 2 in the multipath dispersion of the optical fibre. (b) Discuss the merits
More informationFiber Optic Communication Link Design
Fiber Optic Communication Link Design By Michael J. Fujita, S.K. Ramesh, PhD, Russell L. Tatro Abstract The fundamental building blocks of an optical fiber transmission link are the optical source, the
More informationFiber Optic Communication Systems. Unit-04: Theory of Light. https://sites.google.com/a/faculty.muet.edu.pk/abdullatif
Unit-04: Theory of Light https://sites.google.com/a/faculty.muet.edu.pk/abdullatif Department of Telecommunication, MUET UET Jamshoro 1 Limitations of Ray theory Ray theory describes only the direction
More informationIntroduction to Fiber Optics
Introduction to Fiber Optics Dr. Anurag Srivastava Atal Bihari Vajpayee Indian Institute of Information Technology and Manegement, Gwalior Milestones in Electrical Communication 1838 Samuel F.B. Morse
More informationFIBER OPTICS. Dr D. Arun Kumar Assistant Professor Department of Physical Sciences Bannari Amman Institute of Technology Sathyamangalam
FIBER OPTICS Dr D. Arun Kumar Assistant Professor Department of Physical Sciences Bannari Amman Institute of Technology Sathyamangalam General Objective To understand the propagation of light through optical
More informationDesign of a double clad optical fiber with particular consideration of leakage losses
Vol. (4), pp. 7-62 October, 23 DOI.897/JEEER23.467 ISSN 993 822 23 Academic Journals http://www.academicjournals.org/jeeer Journal of Electrical and Electronics Engineering Research Full Length Research
More informationApplication Note 5596
Polymer Optical Fiber (POF) Application Note 5596 Table of Contents Part 1. POF Overview 1 Introduction 2 Principle of operation 2 Numerical Aperture 2 Modes 3 Attenuation 4 Rayleigh scattering 4 Absorption
More informationOptical Fiber Cable. MODEL:GYTA53 PE Jacket. optic.com. For detailed inquiry please contact our sales team at:
Optical Fiber Cable For detailed inquiry please contact our sales team at: MODEL:GYTA53 PE Jacket market@jfiber optic.com Form one single mode fiber:g.655 Characteristics Conditions Specified Values Units
More informationElements of Optical Networking
Bruckner Elements of Optical Networking Basics and practice of optical data communication With 217 Figures, 13 Tables and 93 Exercises Translated by Patricia Joliet VIEWEG+ TEUBNER VII Content Preface
More informationAbsorption: in an OF, the loss of Optical power, resulting from conversion of that power into heat.
Absorption: in an OF, the loss of Optical power, resulting from conversion of that power into heat. Scattering: The changes in direction of light confined within an OF, occurring due to imperfection in
More informationOptical networking. Emilie CAMISARD GIP RENATER Optical technologies engineer Advanced IP Services
Optical networking Emilie CAMISARD GIP RENATER Optical technologies engineer Advanced IP Services Agenda Optical fibre principle Time Division Multiplexing (TDM) Wavelength Division Multiplexing (WDM)
More informationLecture 3 Fiber Optical Communication Lecture 3, Slide 1
Lecture 3 Dispersion in single-mode fibers Material dispersion Waveguide dispersion Limitations from dispersion Propagation equations Gaussian pulse broadening Bit-rate limitations Fiber losses Fiber Optical
More informationEKT 465 OPTICAL COMMUNICATION SYSTEM. Chapter 2 OPTICAL FIBER COMMUNICATIONS
EKT 465 OPTICAL COMMUNICATION SYSTEM Chapter 2 OPTICAL FIBER COMMUNICATIONS SEMESTER 1-2017/18 3 Credit Hours 222.3 Gbps pada 2017, daripada 6.4Gbps pada 2012 10/3/2017 2 Light Propagation & Transmission
More informationVågrörelselära och optik
Vågrörelselära och optik Kapitel 33 - Ljus 1 Vågrörelselära och optik Kurslitteratur: University Physics by Young & Friedman Harmonisk oscillator: Kapitel 14.1 14.4 Mekaniska vågor: Kapitel 15.1 15.8 Ljud
More informationChapter Ray and Wave Optics
109 Chapter Ray and Wave Optics 1. An astronomical telescope has a large aperture to [2002] reduce spherical aberration have high resolution increase span of observation have low dispersion. 2. If two
More informationClass 4 ((Communication and Computer Networks))
Class 4 ((Communication and Computer Networks)) Lesson 3... Transmission Media, Part 1 Abstract The successful transmission of data depends principally on two factors: the quality of the signal being transmitted
More informationSPECIFICATION. FOR SINGLE-MODE OPTICAL FIBER (FutureGuide -SR15E)
Fujikura DATE Aug. 18, 2008 NO. JFS-00052A Supersedes JFS-00052 Messrs. SPECIFICATION FOR SINGLE-MODE OPTICAL FIBER (FutureGuide -SR15E) Prepared by H. KIKUCHI Manager Optical Fiber and Cable Dept. Global
More informationLecture 18: Photodetectors
Lecture 18: Photodetectors Contents 1 Introduction 1 2 Photodetector principle 2 3 Photoconductor 4 4 Photodiodes 6 4.1 Heterojunction photodiode.................... 8 4.2 Metal-semiconductor photodiode................
More informationOptical Fiber Communication
A Seminar report On Optical Fiber Communication Submitted in partial fulfillment of the requirement for the award of degree Of Mechanical SUBMITTED TO: www.studymafia.org SUBMITTED BY: www.studymafia.org
More informationAnalysis of Dispersion of Single Mode Optical Fiber
Daffodil International University Institutional Repository Proceedings of NCCIS November 007 007-11-4 Analysis of Dispersion of Single Mode Optical Fiber Hossen, Monir Daffodil International University
More informationNEW YORK CITY COLLEGE of TECHNOLOGY
NEW YORK CITY COLLEGE of TECHNOLOGY THE CITY UNIVERSITY OF NEW YORK DEPARTMENT OF ELECTRICAL AND TELECOMMUNICATIONS ENGINEERING TECHNOLOGY Course : Prepared by: TCET 4102 Fiber-optic communications Module
More informationFINAL EXAM 12/12/03 EECS FALL 2003
EECS 412 - FALL 2003 FINAL EXAM 12/12/03 NAME: CWRUnet e-mail address: IMPORTANT INFORMATION: 1. All questions are worth the same. 2. Exam is due December 12 th at 12 noon in Glennan 518. Possible 1. 10
More informationInternational Journal of Advanced Engineering Technology E-ISSN
Research Article ANALYTICAL STUDY OF HELICALLY CLADDED OPTICAL WAVEGUIDE WITH DIFFERENT PITCH ANGLES Mishra V.* Gautam A. K. Taunk B. R. Address for Correspondence Sr. Member IEEE, Electronics Engineering
More informationHow to Speak Fiber Geek Article 2 Critical Optical Parameters Attenuation
Article 2 Critical Optical Parameters Attenuation Welcome back, Fiber Geeks! Article 1 in this series highlighted some bandwidth demand drivers and introductory standards information. The article also
More informationGlass Processing. Younès Messaddeq Centre d optique, Photonique et laser,québec, Canada Spring 2015 JIRU
Glass Processing Lecture 19 # Introduction to Dielectric Waveguide Younès Messaddeq Centre d optique, Photonique et laser,québec, Canada (younes.messaddeq@copl.ulaval.ca) Spring 2015 Lectures available
More information6.014 Lecture 18: Optical Communications
6.014 Lecture 18: Optical Communications A. Overview Optical communications is as old as smoke signals, modulated campfires, and mirrors reflecting sunlight. Today it is even more important, particularly
More informationVALLIAMMAI ENGINEERING COLLEGE SRM Nagar, Kattankulathur 603 203. DEPARTMENT OF ELECTRONICS & COMMUNICATION ENGINEERING EC6702 OPTICAL COMMUNICATION AND NETWORKS QUESTION BANK IV YEAR VII SEM ACDEMIC YEAR:
More informationIntensity Modulation. Wei-Chih Wang Department of Mechanical Engineering University of Washington. W. Wang
Intensity Modulation Wei-Chih Wang Department of Mechanical Engineering University of Washington Why Intensity Modulation Simple optical setup Broadband or mono-chormatic light source Less sensitive but
More informationPhotonics and Fiber Optics
1 UNIT V Photonics and Fiber Optics Part-A 1. What is laser? LASER is the acronym for Light Amplification by Stimulated Emission of Radiation. The absorption and emission of light by materials has been
More informationComparison of FRD (Focal Ratio Degradation) for Optical Fibres with Different Core Sizes By Neil Barrie
Comparison of FRD (Focal Ratio Degradation) for Optical Fibres with Different Core Sizes By Neil Barrie Introduction The purpose of this experimental investigation was to determine whether there is a dependence
More informationAnalysis of Self Phase Modulation Fiber nonlinearity in Optical Transmission System with Dispersion
36 Analysis of Self Phase Modulation Fiber nonlinearity in Optical Transmission System with Dispersion Supreet Singh 1, Kulwinder Singh 2 1 Department of Electronics and Communication Engineering, Punjabi
More informationOptical Transport Tutorial
Optical Transport Tutorial 4 February 2015 2015 OpticalCloudInfra Proprietary 1 Content Optical Transport Basics Assessment of Optical Communication Quality Bit Error Rate and Q Factor Wavelength Division
More informationEC6702-OPTICAL COMMUNICTION AND NETWORKS VII SEM. ECE
EC6702- OPTICAL COMMUNICATION AND NETWORKING TWO MARKS QUESTIONS AND ANSWERS UNIT I - Introduction 1. What are the limitations of optical fiber communication systems? Optical fiber is made up of glass.
More informationOptical Amplifiers (Chapter 6)
Optical Amplifiers (Chapter 6) General optical amplifier theory Semiconductor Optical Amplifier (SOA) Raman Amplifiers Erbium-doped Fiber Amplifiers (EDFA) Read Chapter 6, pp. 226-266 Loss & dispersion
More informationOPTICAL COMMUNICATION AND NETWORKING
A Course Material on By Mr. C.JAGADEESHWARAN ASSISTANT PROFESSOR DEPARTMENT OF ELECTRONICS & COMMUNICATION ENGINEERING SASURIE COLLEGE OF ENGINEERING VIJAYAMANGALAM 638 056 QUALITY CERTIFICATE This is
More informationSilicon Photonic Device Based on Bragg Grating Waveguide
Silicon Photonic Device Based on Bragg Grating Waveguide Hwee-Gee Teo, 1 Ming-Bin Yu, 1 Guo-Qiang Lo, 1 Kazuhiro Goi, 2 Ken Sakuma, 2 Kensuke Ogawa, 2 Ning Guan, 2 and Yong-Tsong Tan 2 Silicon photonics
More informationTotal care for networks. Introduction to Dispersion
Introduction to Dispersion Introduction to PMD Version1.0- June 01, 2000 Copyright GN Nettest 2000 Introduction To Dispersion Contents Definition of Dispersion Chromatic Dispersion Polarization Mode Dispersion
More informationOptical Communication and Networks M.N. Bandyopadhyay
Optical Communication and Networks M.N. Bandyopadhyay Director National Institute of Technology (NIT) Calicut Delhi-110092 2014 OPTICAL COMMUNICATION AND NETWORKS M.N. Bandyopadhyay 2014 by PHI Learning
More informationOPTICAL FIBER COMMUNICATION
OPTICAL FIBER COMMUNICATION Subject Code: IA Marks: 25 No. of Lecture Hrs/Week: 04 Exam Hours: 03 Total no. of Lecture Hrs. 52 Exam Marks: 100 PART - A UNIT - 1 OVERVIEW OF OPTICAL FIBER COMMUNICATION:
More informationSupporting Information: Achromatic Metalens over 60 nm Bandwidth in the Visible and Metalens with Reverse Chromatic Dispersion
Supporting Information: Achromatic Metalens over 60 nm Bandwidth in the Visible and Metalens with Reverse Chromatic Dispersion M. Khorasaninejad 1*, Z. Shi 2*, A. Y. Zhu 1, W. T. Chen 1, V. Sanjeev 1,3,
More information