A3422 XMTDR. Digital Return Optical Transmitter Module. Features

Transcription

1 A3422 XMTDR Digital Return Optical Transmitter Module The A3422 XMTDR digital return optical transmitter allows RF reverse path signals to be sent back to headend via a single fiber. The RF signal is routed to the input of the digital return transmitter via the optical interface module. A -20 db test point on the transmitter is available for measuring RF signal levels to the laser. The drive level is adjusted with a plug-in pad. The transmitter is made of ADC/multiplexing circuit and a DFB laser with 1310 nm, 1550 nm or ITU-T CWDM wavelength. The return transmitter features multiple available wavelengths on the ITU-T standard grid, low distortion characteristics, low RIN noise, and high side mode suppression. The A3422 XMTDR laser transmitter converts the reverse path RF electrical signals into an optical form and launches the resulting optical signal into the fiber back to the HFC headend receiver. Features DFB laser technology ITU-T CWDM grid wavelengths Low distortion characteristics High side mode suppression -20dB test point Plug pad for adjusting RF drive level Low RIN noise Page 1 of 5

2 Block Diagram NET PIN DAC RF Input A RF T/P A TDM De-Multiplexer DAC Optical Output RF Input B RF T/P B NET Digital Diagnostics DC Supply DC-DC Unit μp Unit Page 2 of 5

3 Transmitter Module Layout 6 RF1 Drive Level Pad 3 RF1 Input Test Point Transmitter Mounting Screw 1 Status LED 2 Digital Return SFP Module 6 RF2 Drive Level Pad 4 Transmitter Mounting Screw RF2 Input Test Point ACION 3422 XMTDR Optical Transmitter Module COMPONENT NAME FUNCTION NOTES 1 Status LED Digital Return SFP Module, RF input, Power 2 Digital Return SFP Module 3,4 RF Input Test Point Digitize and transmit a single or two channels -20 db test point for measuring RF drive level to laser 5,6 RF Drive Level Pad Used to set the RF drive level to laser Transmitter Mounting Screw Mounts the optical transmitter to the housing Page 3 of 5

4 Specifications ACI STATION PARAMETERS A3422 XMTDR Digital Return Optical Transmitter Module PARAMETERS CONDITIONS UNITS SPECIFICATION NOTES Optical Specifications Laser type Optical Connector FP, DFB or CWDM SC/APC(standard), Optical return loss Min. db 45 Optical output power Min. dbm Wavelength Spectral Line Width(RMS) RF Specifications DFB or FP laser CWDM laser FP DFB CWDM nm -5 (-5 to 0 typical) for DFB laser 0 (0 to 3 typical) for CWDM laser 1310 ± 20 nm ITU-T CWDM nm 1.5 (typical) 0.4 (typical) 0.4 (typical) Impedance Ω 5 Return loss Max. db -16 RF Input level dbmv Reference to Link Performance below Operating bandwidth MHz 5-45 Other frequencies are available Flatness Peak to Valley db ± 1.0 Link Slope Min. db -3 Link Test point Directional coupler db -20 ± 0.5 Link Performance Full Scale single CW amplitude dbmv 5 Link gain db (typical) Peak NPR db 5 Dynamic 40dB CNR db 20 Environmental Power Consumption Maximum Watt 5.0 Operating Temperature Optical Node Ambient temperature C F -25 to to +185 Relative humidity Non-condensing % 0 to 95 Dimensions D H W Inch. (mm) 5.81 x 1.16 x 2.95 (14.6 x 29.5 x 4.9) Page 4 of 5

5 Ordering Matrix A3410 A3422 XMTDR Digital Return Optical Transmitter Module Module Configuration Configuration sheet Sheet Customer: Created By: Order Date: ORDERING MATRIX 2016/9/13 Position PART NUMBER 3 K D R O T - 8~12 DIGITAL RETURN TRANSMITTER MODULE = 45Mhz, Single RF, Single FP-type Laser, 10km = 45Mhz, Dual RF, Single FP-type Laser, 10km (2-fer) = 45Mhz, Single RF, Single 1310nm DFB-type Laser, 40km = 45Mhz, Dual RF, Single 1310nm DFB-type Laser, 40km (2-fer) = 65Mhz, Single RF, Single FP-type Laser, 10km = 65Mhz, Dual RF, Single FP-type Laser, 10km (2-fer) = 65Mhz, Dual RF, Dual FP-type Laser, 10km = 65Mhz, Single RF, Single 1310nm DFB-type Laser, 40km = 65Mhz, Dual RF, Single 1310nm DFB-type Laser, 40km (2-fer) = 65Mhz, Dual RF, Dual 1310nm DFB-type Laser, 40km = 85Mhz, Single RF, Single FP-type Laser, 10km = 85Mhz, Single RF, Single 1310nm DFB-type Laser, 40km = 85Mhz, Dual RF, Dual 1310nm DFB-type Laser, 40km 81-3 = 85Mhz, Single RF, Single CWDM-type Laser, 80km Single CWDM-type Laser A = 141nm CWDM-type Laser C = 1491nm CWDM-type Laser D = 1511nm CWDM-type Laser E = 1531nm CWDM-type Laser F = 1551nm CWDM-type Laser G = 151nm CWDM-type Laser H = 1591nm CWDM-type Laser J = 1611nm CWDM-type Laser 82 3 = 85Mhz, Dual RF, Dual CWDM-type Laser, 80km Dual CWDM-type Laser 1 Dual CWDM-type Laser 2 A = 141nm CWDM-type Laser C = 1491nm CWDM-type Laser D = 1511nm CWDM-type Laser E = 1531nm CWDM-type Laser F = 1551nm CWDM-type Laser G = 151nm CWDM-type Laser H = 1591nm CWDM-type Laser J = 1611nm CWDM-type Laser 13 OPTICAL CONNECTOR TYPE 1 = LC / UPC (Standard) NOTES: ACI Communications, Inc th Avenue South Kent, WA Rev A Printed in U.S.A. ACI Communications, Inc. reserves the right to discontinue the manufacture or change specifications without prior notice on any parts illustrated in this data sheet. Registered trademarks are the property of their respective owner Page 5 of 5